Академический Документы
Профессиональный Документы
Культура Документы
production-technology.org/tubing-specifications/
Tubing is a relatively small-diameter pipe that is run into a well to serve as a conduit for
the passage of oil and gas to the field surface facilities for processing. Tubing must be
adequately strong to resist loads and deformations associated with production and
workovers. Further, tubing must be sized to support the expected rates of production of
oil and gas.
Tubing Specifications:
Tubing is specified by grade, outer diameter, weight, and connection. API tubing grades
correspond to casing grades with the exception that P grade tubing has a tensile strength
of 105,000 psi and is referred to as P105.
Tubing comes with non-upset (NUE) and external upset (EUE) ends. EUE tubing is more
common, because of the benefit that cutting threads into the tubing ends does not reduce
the body strength.
NB: for ESP applications, if power cable clearance between the tubing and casing becomes
an issue, NUE tubing should be considered.
Internal diameter (ID): is a result of the OD and the wall thickness, and it is used to
calculate pressure losses and velocities.
The drift diameter: is the diameter of a 42” long mandrel that passes through tubing
joint. It is a foremost parameter as it gives the maximum OD of any equipment to run
through the tubing string.
Maximum outside diameter: it depends on the nominal diameter and the connection
type. It is critical as it determines the strings size that we can run in a given casing.
Nominal size: is the outside diameter of the pipe body. The most used sizes are: 2-⅜”,
2-⅞”, 3-½” and 4-½”.
The tubing joint length: is the length of tubing joint including the coupling and
excluding the pin thread. It is classified into two length range: range I: from 20 ft to 24 ft
(6.1 to 7.32 m) long, or range II: from 28 ft to 32 ft (8.53 to 9.75 m) long. The length range
must be chosen with care. It must be compatible with the hoisting and storage capacity of
the mast of the rig used when running in hole the equipment during completion as well as
later on during workover operations.
Nominal weight: is the average linear weight of the tubing, connection included. It is
expressed in lb/ft. It determines the tubing wall thickness. The most common nominal
weights are:
Steel grade: there are mainly two different types of steel used to manufacture tubing:
API standard steels and grades for tubing: J55, C75, L80, N80, C90 and P105. The
letter is a characteristic of the chemical composition and sometimes the thermal
treatment. The number following the letter is the minimum body yield stress in
1000 psi and it is the minimum body yield stress guaranteed by the manufacturer.b
When carbon dioxide and/or hydrogen sulfide are part of the produced fluids, it could
necessary to use stainless steel, alloys, and special pipe. For example:
Connection, threads:
by means of integral joint, the most common type of connection on small diameter
pipe:
by using a coupling (the most common connection), a collar
with internal threads used to join two sections of threaded
pipe.
NB: In addition to providing the seal for the connection, grease is used
to lubricate the threads and protect them from corrosion.
Premium connections:
For premium connections, the seal is made by a metal to metal shoulder (e.g. VAM joint
and Hydril joint), and sometimes by an elastomer or Teflon joint. Premium connections
are preferred for gas wells, high-pressure wells, as well as for wells producing corrosive
effluents.
Mechanical characteristics of tubing pipe:
The pipe run into the well is subjected to variable pressures and temperatures in addition
to its own weight, and these will create variations in stress. The main mechanical
characteristics of tubing pipe are:
Tensile strength: the greatest longitudinal stress that a metal can bear without
tearing apart.
Collapse pressure: expressed in psi or MPa, it is the minimum differential
pressure applied from outside, that the tubing withstand without permanent
deformation.
Burst pressure or internal yield pressure: is the internal differential
pressure that will cause a tubing to fail.
Special tubing:
Special tubings (e.g. fiberglass tubings and internally coated tubings) are used to meet the
particular corrosion resistance requirements due to the presence of hydrogen sulfide or
carbon dioxide and water.
Reference
Casing Specifications
Updated list of API and ISO Standards for Tubulars