Академический Документы
Профессиональный Документы
Культура Документы
Including GST
* At 2000 rpm
MOUNTING KITS
Including all hardware, bolts, belts & nuts to fit compressor to vehicle
Cat NISSAN Compressor needed Price
no.
A1 Nissan GQ 4.2L Diesel with air con. EA80, EA90 or EA100 $295
A13 Nissan GU 4.2L Diesel with air con. EA80 or EA90 $340
A14 Nissan GQ 4.2L Petrol with air con. EA80 or EA90 $350
A15 Nissan GU 4.8 Petrol with air con. EA80 or EA90 $405
C20 Nissan GU 3L Diesel & 3L Diesel EA55 $465
Navara
3
MOUNTING KITS cont.
Including all hardware, bolts, belts & nuts to fit compressor to vehicle
Cat no. TOYOTA Price
B3.0 Toyota Hilux 3L Diesel Intercooled 2005 Model with air con. $360
This kit requires an EA70 Compressor
B3.1 Toyota Hilux 3L Diesel Intercooled 2007/09 Model with air con. $360
This kit requires an EA70 Compressor
B4 Toyota Prado Diesel - Hilux Diesel non-intercooled with air con. 3L $360
This kit requires an EA70 Compressor
A5 Toyota 80/100 Series Petrol 4.5 o/cam. With air con. $315
Will take EA80, EA90 or EA100 Compressor
B17 Toyota New heavy duty low mounting kit for all 1HZ 4.2L Diesels air con. $395
This kit requires an EA70 Compressor
C22 Toyota 79 Series Turbo 4.2 Diesel $425
This kit requires an EA55 Compressor
B19 Toyota 100 Series 4.2L Factory Turbo with air con. $425
This kit requires an EA70 Compressor
C23 Toyota 80 Series 4.2 Factory Turbo Diesel $425
This kit requires an EA55 Compressor
A24 Toyota 80 Series Early model 2H Diesel with air con. POA
4
Universal Mounting Kits
A20 & A21
A20 for EA80, EA90 & EA100
A21 for EA70
Kit Includes
6 Bolts
6 Nuts
12 Washers
A22 & A23
A22 for EA80, EA90 & EA100
A23 for EA70
Kit Includes
5 Bolts
5 Nuts
10 Washers
5
PRICE LIST
Including GST
N.B. Other receivers (tanks) are available. Sizes and prices on request.
6
Brass ¼”BSP non return valve $65
102 (fits between compressor & receiver)
¼” Inlet - ¼” Outlet
¼” Inlet - ½” Outlet
102A
7
109A Brass Hose Barb $4
10mm hose ¼”BSP
8
116 Tyre Inflator Pistol grip with gauge $30
9
124 Brass ¼”BSP Locknut $2
10
KAREELA ENGINEERING
1. Mount compressor to line up with fan belt or air conditioner belt and fit
appropriate length vee belt. Or alternatively position so as to line up with spare vee on
main crank shaft pulley or separate spare vee on air conditioner pulley and fit separate
vee belt. See catalogue for mounting kits. If mounting kit is used, position and
alignment will be taken care of.
2. With compressor mounted and belt fitted drill 13 mm hole in underside of vehicle
air filter and fit hose connection using a locknut. Cut sufficient 8mm hose to connect
to “suc” side of compressor.
3. Mount air manifold on vehicle fire wall or other appropriate position. Run 6mm
Hi Temp Hose from “dis” side of compressor to air receiver. Unlike other
compressors with a much smaller output the output of this compressor must be run
through at least 2m of 6mm Hi Temp Hose. Run 8mm hose from receiver to manifold.
Note: Hi Temp Hose is to be kept clear of other engine fittings due to the heat of this
tube.
4. Fit quick release outlet to air manifold to accept air hose fitting.
5. Electrical connection must be made from an IGN fuse on fuse board to on/off
switch and via pressure switch to compressor clutch using 1.5mm cable.
Kareela Engineering will not be held responsible for any damage caused to your
vehicle while installing your Endless Air compressor
Endless Air - Kareela Engineering
2 Tamar Crt, Mentone, Victoria 3195, Australia
Ph: 9584 4785 / Mob: 0418 175 656 / Fax: 9584 5837
ORDER FORM
Name Date
Town Postcode
VEHICLE DETAILS
Make Mod. Year Air Conditioner Fitted
YES / NO