Академический Документы
Профессиональный Документы
Культура Документы
VD6-XXXXXE3 Series
Typical Features
◆Wide input voltage range ( 2:1), Output power 6W
Test Condition: Unless otherwise specified, data in the datasheet should be tested under the conditions of inputting nominal voltage,
pure resistance rated load and Ta=25℃.
Input Specifications
Stand-by Power Consumption 0.6W (max)
Input Filter π filter
Output Specifications
Output Voltage Accuracy Vo Main circuit≤±2.0% (max); Auxiliary circuit≤±3.0%(max)
Line Regulation Nominal Load, full voltage range Vo ≤±0.5%
Load Regulation 10% ~ 100% nominal load Vo ≤±1%
Ripple & Noise Nominal Load, Nominal Voltage ≤100mVp-p (20MHz bandwidth)
Output Over Voltage Protection 110%~140%Vo
Output Short circuit Protection Continuous, Self-recovery
Dynamic Response 25% nominal load step change △Vo/△t ≤±5.0%/500μs
Output Voltage Adjustment Not available
Startup Delay Time Typical 200ms
General Specifications
Switching Frequency Typical 300KHz
Operating Temperature Refer to temperature derating curve -40℃ ~ +85℃
Storage Temperature -55℃ ~ +125℃
Max Case Temperature Within the scope of work curve +105℃
Relative Humidity non-condensing 5%~95%
Case Material Black Aluminum case
Isolation Voltage Input to Output 1500Vdc ≤ 0.5mA / 1min
5
Meantime Between Failure MIL-HDBK-217F@25℃ 2X10 Hrs
Weight Average
工作温度与输出负载曲线图(常温 25℃)
50
45
40
Output Power Percentage(%)
Operating Temperature(%)
35
30
25
20
15
工作
温度10
5 VD6-24S05E3
0
0 10 20 30 40 50 60 70 80 90 100
Output
输出负载(℃)Load Temperature℃
Stand-by Consumption(W)
80 80
0.21
70 70
0.18
Efficiency(%)
Efficiency(%)
60 60
) 0.15
50 50
VD6-12S05E3 0.12
效率40 效 待机
40 VD6-12S12E3
(% 30 率 功耗 0.09
VD6-12S05E3 VD6-12S15E3
) 30 (W
0.06 VD6-12S05E3
20 VD6-12S12E3 20 VD6-12S12E3
VD6-12S15E3 0.03 VD6-12S15E3
10 10
0 0 0
9 10 11 12 13 14 15 16 17 18 0 5 10 20 30 40 50 60 70 80 90 100
9 10 11 12 13 14 15 16 17 18
输入电压(V) 输出负载(%)
输入电压(V)
输入电压与效率曲线图 输出负载与效率曲线图(标称输入)
Input Voltage and Efficiency Curve Output Load and Efficiency Curve(Nominal Input) 待机功耗与输入电压曲线图
Stand-by Consumption and Input Voltage Curve
100 100 0.3
90 90 0.27
80 80 0.24
Stand-by Consumption(W)
70
70 0.21
60
Efficiency(%)
) 60
Efficiency(%)
0.18
50
50 0.15
效
40 效 40 VD6-24S05E3 0.12
率 30 VD6-24S12E3
率 30 VD6-24S05E3 VD6-24S15E3
待机
0.09
功耗
20 VD6-24S12E3 20 0.06 VD6-24S05E3
10 VD6-24S12E3
10 VD6-24S15E3 0.03
0 VD6-24S15E3
0 0
0 5 10 20 30 40 50 60 70 80 90 100
18 20 22 24 26 28 30 32 34 36 输出负载(%) 18 20 22 24 26 28 30 32 34 36
输入电压(V) 输入电压(V)
Input Voltage(V) Output Load(%) Input Voltage(V)
60
Efficiency(%)
70 0.42
50 60 0.36
机功耗(W)
40 50 0.3
效
率 40 0.24
30 效
VD6-48S05E3
率 VD6-48S05E3
VD6-48S12E3 30 VD6-48S05E3 待 0.18
20 VD6-48S12E3 VD6-48S12E3
VD6-48S15E3 20 0.12 VD6-48S15E3
10 VD6-48S15E3
10 0.06
0
0 0
36 40 44 48 52 56 60 64 68 72 75 0 5 10 20 30 40 50 60 70 80 90 100 36 40 44 48 52 56 60 64 68 72 75
Input输入电压(V)
Voltage(V) 输入电压(V)
输出负载(%)
Output Load(%) Input Voltage(V)
Output Rise time waveform(Nominal input full Load) Output drop time waveform(Nominal input full Load)
EMC Characteristics
CE CISPR22/EN55022 CLASSA(bare board)/CLASSB (external circuit needed)
EMI
RE CISPR22/EN55022 CLASSA(bare board)/CLASSB (external circuit needed)
ESD IEC/EN61000-4-2 Contact ±4KV
RS IEC/EN61000-4-3 10V/m
EFT IEC/EN61000-4-4 ±2KV (external circuit needed)
EMS Surge IEC/EN61000-4-5 ±2KV (external circuit needed)
CS IEC/EN61000-4-6 3Vr.m.s
Voltage dips, short interruptions and
IEC/EN61000-4-29 0%-70%
voltage variations immunity
VD6-24S12E3 conducted emission positive of power supply test result VD6-24S12E3 conducted emission negative of power supply test result
MOV TVS
C0 C1
EUT LOAD
Recommended Circuit for Single Output Product Recommended Circuit for Dual Output Product
Packing Dimension
2, 3 22, 23 14 16 9 11
Single Output(S)
-Vin +Vin +Vo GND NP NC
Positive Negative 2, 3 22, 23 14 16 9 11
Dual Output (D) -Vin +Vin +Vo 0V 0V -Vo
* Note: If the definition of pin is not in accordance with the model selection manual, please refer to the label on actual item.
Dimension
Application Recommendation:
1.The recommended minimum load is 5%-10%, output ripple might rise under no load, other performances are not affected basically;
2. The recommended unbalance degree of the dual output module load is≤±5%;
3. The Max capacitive load offered was tested under pure resistance and full load condition;
4. Our company can provide overall solution for power supply, or custom made product;
5. Due to space limitation, please contact our sales team for more information.