Академический Документы
Профессиональный Документы
Культура Документы
Caution: Do not connect the USB cable until after FortiExplorer has been installed. For more information about using Web Config and the CLI, see the Install Guide. FortiWifi 60C LINK/ACT
SPEED
PWR STATUS HA SDHC 1 2 3 4 5 EXPRESS CARD DMZ RJ-45 10/100 Base-T Ethernet Optional connection to a DMZ
HA Green The unit being used in an HA cluster. network or to other
Power FortiGate units for high avail-
HA Express Card Green SDHC card is inserted and detected.
LED Status LED Interface ability (HA).
Status LEDs slot SDHC
SDHC CARD LED Data is reading from or writing to the SDHC
Flashing Green Console RJ-45 9600 Bps RS-232 Optional connection to the
slot on left card. 8/N/1 management computer. Pro-
side of unit vides access to the command
Green Port is online (link).
LINK/ line interface (CLI).
Antenna mount RJ-45 Serial Antenna mount Flashing Port is receiving or sending data (activity).
ACT
Connection Green USB USB A USB Optional connection for the
Ports 1 to 5 USB key, modem, or backup
CONSOLE Green Connected at 1000 Mbps.
operation.
Speed Amber Connected at 100 Mbps.
USB Man- USB B Client port for management/
Off Connected at 10 Mpbs. agement configuration by FortiExplorer.
DC+12V USB MGMT USB DMZ WAN2 WAN1 5 4 3 2 1
Green Port is online (link). Express- Express- The Universal ExpressCard
USB LINK/ Card slot Card/34 slot adds wireless communica-
Power DMZ WAN2 WAN1 Flashing Port is receiving or sending data (activity).
Connection ACT tions. Not supplied.
Internal Interfaces WAN1, WAN2, Green
1 to 5 and DMZ SDHC 4GB, Class 6 or SDHC card slot for storage or
Ground Amber Connected at 100 Mbps.
Speed CARD 8GB, higher required applications. To utilize
Off Connected at 10 Mpbs. 16GB, all features, a minimum size of
Flashing Green Wireless port is active. or 32GB 16GB is required. Maximum
WiFi SDHC size 32GB. One 4GB card
Off Wireless port is not active. installed.
Connecting
FortiGate-30B
SDHC Cards
WiFi INTERNAL WAN1 WAN2 DMZ
FortiWifi 60C LINK/ACT
SPEED
AC Power Cable
PWR STATUS HA SDHC 1 2 3 4 5 EXPRESS CARD
Attach the antennae to the back of the FortiWifi unit. Refer to the wall mount template to
Trademarks
REGISTER
SDHC attach your unit to a wall. The FortiWifi-60C unit comes with a 4GB SDHC installed. Follow the steps below to install
CARD
Connect the following to the FortiWifi unit. Ensure the FortiWifi unit is placed on a stable new SDHC card in the unit. Ensure to format the SDHC card after installation into the unit.
Straight-through
Ethernet cable
4GB SDHC card USB A to USB B
Cable
surface. To install a new SDHC card in the unit:
installed
• Insert a network cable to WAN1. Insert the other end to the router connected to the 1. Power down the unit by unplugging the AC power cable from the outlet to insert
Factory Defaults •
Internet, or to the modem.
Connect a network cable to an internal interface. 2.
or remove the SDHC card. The SDHC card is NOT hot swappable.
The SDHC slot is located on left side of unit. To open, remove the two screws from
• Insert the other end to a computer or switch. the SDHC CARD panel.
Administrator user name admin 3. To remove a SDHC card, press the card in and it will eject itself from the slot.
• Connect the AC Power Cable to the Power Supply.
Administrator password (none) 4. Insert the SDHC card (32GB maximum capacity, Class 6 or higher) into the SDHC
• Connect the Power Cord to a surge protected power bar or power supply.
NAT/Route mode CARD slot.
Internal interface 192.168.1.99 ExpressCard 5. Replace the SDHC CARD panel and tighten screws.
WAN1 192.168.100.99 Insert the ExpressCard (not supplied) into the ExpressCard 3G slot. 6. Plug the AC cable back into the outlet and login to the web-based manager.
WAN2 192.168.101.99 7. In the CLI console, type exec formatlogdisk to format the SDHC card.
To reset the FortiGate unit to the factory defaults, press the Reset button or type in the
CLI command:
execute factoryreset
It may take 4-5 minutes to reboot the unit.