Академический Документы
Профессиональный Документы
Культура Документы
Asian DP2-20 DP2-60 DP2-80 DP2-21 DP2-41 DP2-61 DP2-22 DP2-42 DP2-62
the hexagon-socket-head plug supplied as accessory.
North American (Note) DP2-20F(-P) DP2-40N DP2-60N DP2-21F(-P) DP2-41N DP2-61N DP2-22F(-P) DP2-42N DP2-62N
Item European DP2-40E DP2-60E DP2-41E DP2-61E DP2-42E DP2-62E 䢇 Piping
• When connecting a 12mm spanner
Type of pressure Gauge pressure
hexagon-socket-head plug
Rated pressure range 0 toⳮ101.3kPa 0 to 100.0kPa 0 to 1.000MPa or coupling to the pressure
Set pressure range 5.1 toⳮ101.3kPa ⳮ5.0 to 100.0kPa ⳮ0.050 to 1.000MPa port, hold the hexagonal
part of the pressure port
Pressure withstandability 490kPa 1.47MPa
with a 12mm spanner and
Applicable fluid Non-corrosive gas make sure that the
Selectable units kgf/cm2, bar, psi, mmHg, inHg kgf/cm2, bar, psi tightening torque is 9.8N䡠m
or less. Also, in order to prevent any leakage, wind a sealing
Supply voltage 12 to 24V DC Ⳮ 10
ⳮ15 % Ripple P-P 10% or less
tape on the coupling when connecting.
Current consumption 50mA or less However, sealing tape is not required for North American type
<Asian, North American (Standard NPN output • Flat • IP67 types)> <North American (Standard PNP output type), European> using NPTF 1/8 coupling. (Sealing tape is required if NPT1/8
NPN open-collector transistor PNP open-collector transistor coupling is used.)
Comparative outputs
Comparative Output 1 • Maximum sink current: 100mA • Maximum source current: 100mA
(Comparative Output 2 ) • Applied voltage: 30V DC or less (between comparative output and 0V) • Applied voltage: 30V DC or less (between comparative output and ⳭV) Flat type, Light weight type
• Residual voltage: 1V or less (at 100mA sink current) • Residual voltage: 2V or less (at 100mA source current)
0.4V or less (at 16mA sink current) 䢇 Setting of pressure lead direction
• The pressure lead direction can be changed by dismantling
Equipped with 4 types of modes: hysteresis mode, window comparator mode, dual output mode, automatic sensitivity the pressure port attachment and changing the mounting
Output modes
setting mode (selectable by key operation) direction. The tightening torque of the hexagon-socket-head
Hysteresis 1 digit (However, variable in hysteresis mode and 2 digits when using psi unit) bolt (length 9mm or less) should be 0.29N䡠m or less.
Repeatability WithinⳲ0.2% F.S.Ⳳ1 digit Pressure port attachment
Response time 2.5ms or less Hexagon-socket-
head bolts
Short-circuit protection Incorporated
Main body
Output voltage (V)
Guide holes
–10
1.3k
Pa
5 ( ) vacuum side in case of vacuum pressure
OU
type sensor.
T1
OU
T2
Note: The analog voltage output is not incorporated with a short-circuit the upper limit of dis- Comparative
type
protection circuit. Do not directly connect a power supply or a playable pressure range. Output 1 OFF Hysteresis: 1 digit
2 digits when
capacitive load. When using the analog voltage output, take ON (
using psi unit )
pressure
0
Vacuum
care to connect external equipment of proper input impedance. Applied pressure exceeds Comparative
0
Also, when a cable extension is used, voltage drop due to cable the lower limit of display- Output 2 OFF
type
Symbols …D: Reverse supply polarity protection diode the lower limit of display- (Positive pressure type)
type
ZD1, ZD2, ZD3: Surge absorption zener diode able pressure range. High vacuum
Tr1, Tr2: NPN output transistor (Vacuum pressure type)
pressure
0
Vacuum
06H0133
Downloaded from www.Manualslib.com manuals search engine
11 SETTING 3 Setting of pressure values
䢇 If key-protect has been set, make sure to release key- For the case when output mode is set to either the hysteresis mode For the case when the output mode is set to automatic
protect before operating the keys. (Please refer to 15 KEY- ( ), window comparator mode ( ) or dual output mode ( ). sensitivity setting mode ( )
PROTECT FUNCTION for the procedure.)
䢇 The conditions which are set are stored in an EEPROM. 䢇 [Set Value 1 (P1)] and [Set Value 2 (P2)] of the comparative 䢇 Comparative outputs’ [Set Value 1 (P1)], [Set Value 2 (P2)]
Kindly note that the EEPROM has a life span and its outputs are set. and [Set Value 3 (P3)] are set.
guaranteed life is 100,000 write operation cycles.
• The setting of Set Value 2 (P2) with respect to Set Value 1 • The setting of Set Value 2 (P2) with respect to Set Value 1
Setting procedure (P1) can only be towards the high pressure side in case of (P1) can only be towards the high pressure side in case of
the positive pressure type sensor and only towards the high the positive pressure type sensor and only towards the high
1 2 3
Zero-point Initial Pressure Measurement vacuum side in case of the vacuum pressure type sensor. vacuum side in case of the vacuum pressure type sensor.
adjustment setting value setting • Set Value 1 (P1) and Set Value 2 (P2) can be made common • Set Value 3 (P3) is automatically set to the mid-value of Set
for all the output modes. However, when a changeover is Value 1 (P1) and Set Value 2 (P2). However, if Set Value 1
Adjust Set [Display], Enter Commence
zero-point [Output mode], Set Value 1 (P1) measurement made to the automatic sensitivity setting mode, since Set (P1) is set to a value on the vacuum pressure side for a
and [Unit] Set Value 2 (P2) on completion Value 3 (P3) has not been set, make sure to carry out the positive pressure type sensor or to the positive pressure side
Set Value 3 (P3) of setting pressure value settings for the automatic sensitivity mode. for a vacuum pressure type sensor, Set Value 3 (P3) is
automatically set to the mid-value of ‘zero’(atmospheric
1 Zero-point adjustment pressure) and Set Value 2 (P2). Further, if both, Set Value 1
Set to Set Value 1 (P1) set mode
(P1) and Set Value 2 (P2) are set to a value on the vacuum
䢇 The displayed pressure when the pressure port is left open is DP2-20 –101.3kPa
• In the sensing mode, press MODE key. pressure side for a positive pressure type sensor or to the
adjusted to zero. • and Set Value 1 (P1) which is being positive pressure side for a vacuum pressure type sensor, Set
Set to sensing mode set are displayed alternately. Value 3 (P3) is automatically set to ‘zero’(atmospheric
• The figure on the left shows the display of
OUT1 OUT2
pressure).
• The sensor will automatically enter the
MODE
a vacuum pressure type sensor when the • The automatically set Set Value 3 (P3) can be changed manually.
0-ADJ
DP2-20 –101.3kPa
sensing mode when power is supplied. pressure unit has been set to ‘kPa’. • Since display of error messages is not possible during
• The figure on the left shows the display pressure value setting in the automatic sensitivity setting
OUT1 OUT2
Displayed
MODE when the pressure unit and display are set mode, make sure that the sensor is used within the rated
0-ADJ
alternately
to ‘kPa’ and ‘digital display’, respectively. pressure range.
DP2-20 –101.3kPa
Perform zero-point adjustment OUT1 OUT2 Set to Set Value 1 (P1) set mode
MODE
DP2-20 –101.3kPa
• In the sensing mode, press MODE key.
pressure (i.e., no applied pressure condi- • and Set Value 1 (P1) which is being
tion), and press, simultaneously, the incre- set are displayed alternately.
OUT1 OUT2
Enter Set Value 1 (P1) OUT1 OUT2
released, zero-point adjustment is • In case of the positive pressure type pressure unit has been set to ‘kPa’.
completed and the sensor returns to the sensor, if key is pressed once the set Displayed
sensing mode.
OUT1 OUT2
MODE
value changes towards the high pressure alternately
DP2-20 –101.3kPa • If pressure has been applied during zero-
0-ADJ
side by 1 digit and if key is pressed DP2-20 –101.3kPa
point adjustment, is displayed when once the set value changes towards the
the keys are pressed. Bring the applied low pressure side by 1 digit.
OUT1 OUT2 Displayed OUT1 OUT2
pressure to atmospheric pressure (i.e., no In case of the vacuum pressure type MODE
MODE
alternately
0-ADJ
applied pressure condition) and carry out sensor, if key is pressed once the set 0-ADJ
DP2-20 –101.3kPa
the zero-point adjustment once again. value changes towards the high vacuum
side by 1 digit and if key is pressed
2 Initial setting
OUT1 OUT2
once the set value changes towards the Enter Set Value 1 (P1)
MODE
0-ADJ low vacuum side by 1 digit.
䢇 Pressure [Unit], [Display] and [Output mode] of the • If key or key is pressed con- DP2-20 –101.3kPa
• Within the required permissible pressure
comparative outputs are set. tinuously, the set value changes quickly. range, having created a pressure state
which is nearest to the atmospheric
Set to initial setting mode • If the set pressure range is exceeded, OUT1 OUT2
pressure, press key.
either (upper limit exceeded) or MODE
DP2-20 –101.3kPa • In the sensing mode, press MODE key while (lower limit exceeded) is displayed.
0-ADJ
DP2-20 –101.3kPa
• The setting of Set Value 1 (P1) can be
• The settable digit changes when key repeated several times in the Set Value 1
OUT1 OUT2
is pressed. Displayed (P1) set mode.
0-ADJ
MODE
alternately
DP2-20 –101.3kPa
0-ADJ
MODE
OUT1 OUT2
• and Set Value 2 (P2) which is being
Enter Set Value 2 (P2) MODE set are displayed alternately.
0-ADJ
DP2-20 –101.3kPa
• Using key and key, enter in a
Change with key. manner similar to that for entering Set
Value 1 (P1). Displayed
3rd digit 2nd digit 1st digit OUT1 OUT2
MODE
: kPa or : Hysteresis : Digital alternately 0-ADJ
alternately.
06H0145
• If the set pressure range is exceeded,
Set to sensing mode OUT1 OUT2
either (upper limit exceeded) or
MODE
Set to sensing mode (lower limit exceeded) are displayed
DP2-20 –101.3kPa • Press MODE key. 0-ADJ
are not erased even if the power supply is (P2) set mode.
switched off. stored in an EEPROM, they are not
• The figure on the left shows the display erased even if the power supply is
when the unit and display are set to ‘kPa’ switched off.
and ‘digital display’, respectively.
Downloaded from www.Manualslib.com manuals search engine
13 CONVERSION OF PRESSURE UNITS
䢇 In the DP2 series, the conversion to different units is automatically done on changing the setting of the pressure unit. However,
this conversion can also be obtained by multiplying the values by the coefficients given in the following table.
Set to Set Value 3 (P3) set mode
Conversion procedure
DP2-20 –101.3kPa • In the Set Value 2 (P2) set mode, press
MODEkey. • For example, if 2kPa is to be expressed in kgf/cm2, since 1kPa=1.01972⳯10ⳮ2kgf/cm2, 2kPa becomes 2⳯1.01972⳯10ⳮ2 c 0.020kgf/cm2
OUT1 OUT2 • and the automatically set Set Value Conversion table for pressure units
0-ADJ
MODE
3 (P3) are displayed alternately.
• In case mmHg
Set Value 1 (P1) = ⳮ50.0kPa kPa MPa kgf/cm2 bar psi inHg atm
(Torr)
Displayed Set Value 2 (P2) = ⳮ100.0kPa
alternately then
ⳮ50.0Ⳮ(ⳮ100.0) 1kPa 1 1⳯10ⳮ3 1.01972⳯10ⳮ2 1⳯10ⳮ2 1.45038⳯10ⳮ1 7.50062 0.2953 9.86923⳯10ⳮ3
DP2-20 –101.3kPa Set Value 3 (P3) = = ⳮ75.0kPa
2
Digits smaller than the displayed digits
OUT1 OUT2
(
are discarded. ) 1MPa 1⳯103 1 1.01972⳯10 1⳯10 1.45038⳯102 7.50062⳯103 0.2953⳯103 9.86923
MODE
0-ADJ
value changes towards the high pressure 䢇 These functions are convenient for finding the pressure OUT1 OUT2
it immediately when is displayed.
MODE
0-ADJ
side by 1 digit and if key is pressed variation range or for determining the reference for pressure
0-ADJ
MODE • Key-protect is set and the sensor returns
once, the set value changes towards the settings. to the sensing mode.
Displayed low pressure side by 1 digit.
In case of a vacuum pressure type • Please note that the peak value and the bottom value data
alternately
is erased when it is no longer displayed.
sensor, if key is pressed once the set • Since the key-protect information is stored in an EEPROM,
DP2-20 –101.3kPa
value changes towards the high vacuum • The response time of the comparative outputs becomes
it is not erased even if the power supply is switched off.
slower during the peak hold and bottom hold display.
side by 1 digit and if key is pressed • Please take care to remember if the key-protect function
once the set value changes towards the
OUT1 OUT2
until is displayed. (4 sec. approx.) continuously for about 3 sec. and release
(lower limit exceeded) is displayed. When the finger is released after is OUT1 OUT2
it immediately when is displayed.
OUT1 OUT2
MODE
displayed, the peak value and are 0-ADJ
MODE
• Key-protect is released and the sensor
0-ADJ
displayed alternately. returns to the sensing mode.
Set to sensing mode
• If the applied pressure exceeds the
DP2-20 –101.3kPa • Press MODE key.
Displayed displayable pressure range, error
• The sensor returns to the sensing mode message ( or ) and are • When the keys are to be operated, make sure that key-
alternately
OUT1 OUT2 after Set Value 1 (P1), Set Value 2 (P2) displayed alternately. In this case, bring protect is released.
MODE and Set Value 3 (P3) have been set. DP2-20 –101.3kPa
back the applied pressure to within the
• Since the values which have been set are
0-ADJ
MODE
0-ADJ
MODE
Overseas Sales Dept.
• Please note that if any key, except key, is pressed in any MODE 0-ADJ
Phone: ⴐ81-(0)568-33-7861
setting mode, the set conditions shall get changed. FAX: ⴐ81-(0)568-33-8591
Downloaded from www.Manualslib.com manuals search engine PRINTED IN JAPAN