Академический Документы
Профессиональный Документы
Культура Документы
10)
* For LD5100 5th firmware (Image Control-ver51, Print Control-ver51, Operation-ver50, Finisher-ver15) Nov.7, '05
DIPSW No Bit Functions 0 1 Default values
BT MG PAS MGUS Taiwan
DIPSW1 0 - - - 1 1 1 1 1
1 - - - 0 0 0 0 0
2 Print stop method after toner supply or *1 *1 1 1 1 1 1
3 waste toner full display *1 *1 0 0 0 0 0
4 Prohibition of printing when the PM count Not prohibited Prohibited 0 0 0 0 0
is reached
5 Print number setting until printing is *2 *2 0 0 0 0 0
6 prohibited after PM is displayed *2 *2 0 0 0 0 0
7 *2 *2 0 1 1 1 1
HEX 85 85 85 85
DIPSW2 0 Hard disk connection Disconnected Connected 0 0 0 0 0
1 - - - 0 0 0 0 0
2 Switchover of the paper exit speed For machines with For machines with 1 1 1 1 1
(countermeasure against uneven wax) countermeasures countermeasures
against uneven wax against uneven wax
not provided provided
3 Switchover of the paper exit full detection For machines with For machines with 1 1 1 1 1
sensor logic countermeasures countermeasures
against uneven wax against uneven wax
not provided provided
4 'Control of the LCT paper feed assist fan' *3 *3 0 0 0 0 0
5 is moved to key operator mode *3 *3 0 0 0 0 0
6 Switchover of the rotational speed of the *4 *4 1 1 1 1 1
7 polygon motor *4 *4 0 0 0 0 0
HEX 4C 4C 4C 4C
DIPSW3 0 Countermeasures for J32-03 on 11x17 Countermeasures Former control 0 0 0 0 0
paper (more than 320mm) control
HEX 01 01 01 01
DIPSW23 0 - - - 0 0 0 0 0
1 Output when EKC (ECM) user ID is Enabled (counted as Disabled (registered 0 0 0 0 0
unmatched (IP) the other user) in JOB list)
7 - - - 0 0 0 0 0
HEX 20 20 20 20
DIPSW24 0 Color space change, Wide to narrow Disabled Enabled 0 0 0 0 0
1 Vs/Vp switch control *21 Disabled *21 Enabled 0 0 0 0 0
2 Image stabilization control timing *22 *22 0 0 0 0 0
3 *22 *22 1 1 1 1 1
4 Image stabilizing control execution timing *33 *33 0 0 0 0 0
5 By standby time *33 *33 0 1 1 1 1
6 Image stabilizing control execution timing *34 *34 0 0 0 0 0
7 By output sheets *34 *34 0 1 1 1 1
HEX A8 A8 A8 A8
DIPSW25 0 - - - 0 0 0 0 0
1 - - - 0 0 0 0 0
2 - - - 0 0 0 0 0
3 Color registration correction control *23 *23 0 0 0 0 0
4 *23 *23 0 1 1 1 1
5 Color registration fine correction Yes No 0 0 0 0 0
6 - - - 0 0 0 0 0
7 De-humid heater ON OFF 0 0 0 0 0
HEX 10 10 10 10
DIPSW26 0 - - - 0 0 0 0 0
1 - - - 0 0 0 0 0
2 - - - 0 0 0 0 0
3 - - - 0 0 0 0 0
4 - - - 0 0 0 0 0
5 - - - 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 00 00 00 00
DIPSW27 0 - - - 0 0 0 0 0
1 - - - 0 0 0 0 0
2 - - - 0 0 0 0 0
3 - - - 0 0 0 0 0
4 - - - 0 0 0 0 0
5 - - - 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 00 00 00 00
DIPSW28 0 - - - 0 0 0 0 0
1 - - - 0 0 0 0 0
2 Toner refresh mode (at job end) *24 Disabled *24 Enabled 0 1 0 1 0
3 Toner refresh mode (periodical) *24 Disabled *24 Enabled 0 0 0 0 0
4 Printer gamma offset adjustment *25 Only high light *25 Whole area 0 0 0 0 0
5 PK punch mode restriction Enabled Disabled 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 04 00 04 00
DIPSW29 0 Specification of the number of executions *24 *24 0 1 1 1 1
1 of the toner refresh mode 0 0 0 0 0
2 Change of the 1st transfer current for a Not included Included 0 1 1 1 1
countermeasure against white spots
3 Include of proof copy to the set copy Not included Included 1 0 0 0 0
4 - - - 0 0 0 0 0
5 For manufacturing - - 0 0 0 0 0
6 'FNS countermeasures against uneven *32 *32 0 0 0 0 0
wax' is moved to key operator mode
LD5100 software DIPSW list (for PR5100 ver2.10)
* For LD5100 5th firmware (Image Control-ver51, Print Control-ver51, Operation-ver50, Finisher-ver15) Nov.7, '05
DIPSW No Bit Functions 0 1 Default values
BT MG PAS MGUS Taiwan
7 - - - 0 0 0 0 0
HEX 05 05 05 05
DIPSW30 0 - - - 0 0 0 0 0
1 Restriction of the display of the 36 mode Restricted Not restricted 0 1 1 1 1
data collection
2 - - - 0 0 0 0 0
3 - - - 1 1 1 1 1
4 - - - 0 0 0 0 0
5 - - - 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 0A 0A 0A 0A
DIPSW31 0 - - - 1 1 1 1 1
1 - - - 0 0 0 0 0
2 - - - 0 0 0 0 0
3 - - - 0 0 0 0 0
4 - - - 0 0 0 0 0
5 - - - 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 01 01 01 01
DIPSW32 0 - - - 0 0 0 0 0
1 Auto reset function of the special paper Enabled Disabled 0 1 1 1 1
setting on the by-pass tray
2 - - - 0 0 0 0 0
3 ADU reverse motor operation *35 Rubber roller *35 Spike roller 1 0 0 0 0
4 - - - 0 0 0 0 0
5 - - - 0 0 0 0 0
6 - - - 0 0 0 0 0
7 - - - 0 0 0 0 0
HEX 02 02 02 02
* 2 Print number setting until printing is prohibited after PM is * 8 Size detection switchover 4
displayed
Mode 1-7 1-6 1-5 Mode 13-4 13-3
1000 prints 0 0 0 A5R 0 0
2000 prints 0 0 1 B6R 0 1
3000 prints 0 1 0 5.5×8.5R 1 0
4000 prints 1 1 0 − 1 1
5000 prints 1 0 0
1000 prints 1 0 1 * 9 F4 size setting
1000 prints 0 1 1 Mode 13-6 13-5
1000 prints 1 1 1 8×13 0 0
8.25×13 0 1
* 3 Control of the LT paper feed assist fa Move to key operator mode 8.125×13.25 1 0
Mode 2-5 2-4 8.5×13 1 1
ON for coated paper only 0 0
ON for all types of paper 0 1 *10 FNS alarm stop method
ON for all types of paper 1 0 This setting is used to determine when to stop if a FNS
OFF at all times 1 1 full alarm is detected.
Funsctions detected are;
Lower limit of the FNS tray, the number of the FNS trays,
FNS booklet tray, PK punch scraps, TU scraps and TU
* 4 Switchover of the rotational speed of the polygon motor stacker
Mode 2-7 2-6 Mode 15-4 15-3
Stops immediately after
1/1 speed 0 0 0 0
detection
Stops at a break between copy
1/1 speed 0 1 0 1
set after detection
2/3 speed 1 0 Does not stop while in printing 1 0
1/2 speed 1 1 Does not stop while in printing 1 1
*13 Fixing temperature selection *19 Main scan correction of the color registration auto correction
Temperature up: Decrease an insufficient fixing or fixing (periodical correction)
winding jam The color registration corrections, in the main scanning
Temperature down: Decrease paper exit curling or waving direction that are periodically performed can be omitted.
Mode 19-3 19-2 19-1 This is used temporarily when there is a registration
Upper roller, lower roller: -30C 0 0 0 error along the main scan as a result of a trouble
Upper roller, lower roller: -20C 0 0 1 around the transfer belt unit, or when separating
Upper roller, lower roller: -10C 0 1 0 faulty points.
Standard 0 1 1 Mode 23-4
Upper roller: standard, 1 0 0 Enabled 0
Lower roller: +10C Disabled 1
Standard 1 0 1
Standard 1 1 0 *20 IP gamma correction
Standard 1 1 1 In order to separate defective items when there is poor
images sent from IP, the gamma correction can be omitted.
*14 Default resolution of the IP scanner The gamma correction table is stored in the printer
Mode 19-7 19-6 controller.
400dpi 0 0
600dpi 0 1 Note:
200dpi 1 0 * When installing the printer controller, be sure that the setting
300dpi 1 1 is made to '1'.
Mode 23-5
*15 Image scanning area with shift function Enabled 0
Normal: Compare the original size and the transfer paper Disabled 1
size and the smaller one is to be the image area.
Original priority: *21 Vs/Vp switch control
Original size is to be the image area. This Vs/Vp switch control is used when there is an image
erasure around a solid image in the half-tone section in
early stage after the change of developer.
Mode 20-1 Mode 24-1
Normal 0 Disabled 0
Original priority 1 Enabled 1