Академический Документы
Профессиональный Документы
Культура Документы
INTENDED USES To provide a temporary barrier against corrosion during manufacture, transit and erection of steel
structures which will be subjected to heat such as pipework, boilers, flues, chimneys, pipelines etc.
The decompostion characteristics of this product allow its use in the burner section of power
stations.
Drying Time
Overcoating Interval with
recommended topcoats
Temperature Touch Dry Hard Dry Minimum Maximum
Protective Coatings
Page 1 of 4
Issue Date:30/07/2015
Ref:2499
Intertherm® 79
Temporary Protective Primer
SURFACE All surfaces to be coated should be clean, dry and free from salt contamination. Prior to paint
PREPARATION application, all surfaces should be assessed and treated in accordance with ISO 8504:2000.
Intertherm 79 can be applied over smooth solvent cleaned substrates as well as abrasive blast
cleaned surfaces. Application over blast cleaned substrates gives improved anti-corrosive
performance.
APPLICATION Mixing This material is a one component coating and should always be mixed
thoroughly with a power agitator before application.
Work Stoppages Thoroughly flush all equipment with International GTA007. All unused
material should be stored in tightly closed containers. Partially filled
containers may show surface skinning and/or a viscosity increase of the
material after storage. Material should be filtered prior to use.
Clean Up Clean all equipment immediately after use with International GTA007. It is
good working practice to periodically flush out spray equipment during the
course of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays.
Page 2 of 4
Intertherm® 79
Temporary Protective Primer
PRODUCT Intertherm 79 has been specially designed to act as temporary anti-corrosion protection for steel
CHARACTERISTICS structures during manufacture, fabrication and erection. It is particularly useful where steelwork will
be subjected to elevated temperatures once placed in service. On heating the coating will degrade
to yield an inert residue on the surface and release minimal amounts of organic condensation
products into the atmosphere, thereby allowing the use of Intertherm 79 in flues, ducts and
chimneys etc., with no effect on filtration systems.
Maximum film build in one coat is best attained by airless spray. When applying by methods other
than airless spray, the required film build is unlikely to be achieved. Application by air spray may
require a multiple cross spray pattern to attain maximum film build. Low or high temperatures may
require specific application techniques to achieve maximum film build.
Surface temperature must always be a minimum of 3°C (5°F) above dew point.
This product is not intended for use in aggressive, corrosive environments, or on heavily pitted or
contaminated steel.
Note: VOC values are typical and are provided for guidance purpose only. These may be subject to
variation depending on factors such as differences in colour and normal manufacturing tolerances.
SYSTEMS In most circumstances this product is applied direct to steel and is not overcoated.
COMPATIBILITY
Page 3 of 4
Intertherm® 79
Temporary Protective Primer
D ADDITIONAL Further information regarding industry standards, terms and abbreviations used in this data sheet
INFORMATION can be found in the following documents available at www.international-pc.com:
et
ail
T • Definitions & Abbreviations
o
p • Surface Preparation
• Paint Application
SAFETY This product is intended for use only by professional applicators in industrial situations in
PRECAUTIONS accordance with the advice given on this sheet, the Material Safety Data Sheet and the
container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS)
which International Protective Coatings has provided to its customers.
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and
fumes will be emitted which will require the use of appropriate personal protective equipment and
adequate local exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult International Protective Coatings
for further advice.
Rect Top
PACK SIZE Unit Size
Vol Pack
20 litre 20 litre 20 litre
This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this document. Should there be any
discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the version on the website will take precedence.
All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies.
www.international-pc.com
Page 4 of 4