Академический Документы
Профессиональный Документы
Культура Документы
Perform general cleaning works for all areas surrounding the building,
including green area behind the main building and any waste material left
1.3 L.S. 1.00 $ -
behind from previous contractor, and to properly dispose of all waste to an
approved dump site.
Total of Bill No. 1 $ -
Block Works: All works of this bill shall be of Concrete blocks Grade 35 of high
quality standards and as per specifications.
Block works shall be measured in meter square. The net measurement of the
complete elevations, excluding all openings and voids more than 0.1 M. S. in
area.
No allowance for thickness used other than those shown in the drawings.
Spply and install high quality italian or spanish granite for WC sinks 3cm thick.
Price to include steel frame 4*4 cm. price also include open for sink as per
3.4 M.S. 13.00 $ -
details and drawings. The area measured for top granite only. Color shall be
selected by Engineer.
Supply and install ceramic wall tile 60x20x0.6cm at PIEFZA Kitchen and
Cafeteria; price to include fixing wall tiles with adhesive, pointing with similar
3.5 M.S. 6.80 $ -
to selected color of tile and cleaning on site. Color shall be selected by
Engineer.
Parquet Flooring: Supply & Install Parquet laminate floor: 8mm white oak
parquet laminate (Italian of German source or equivalent) to be applied to
the areas specified in the floor planned attached with an estimated area of
divided as for the first floor and for the second floor. The Finishing works
(including under Parquet pad and side panel) with all necessary accessories
3.6 M.S. 350.00 $ -
should obtain the Supervising Engineer’s approval prior to the
commencement of the work. A sample of the material is to be supplied by the
contractor to be approved prior to the commencement any purchases or
construction work in relation to this item.
Supply and install 2.00mm anti- microbial and anti-fungal epoxy floor with
pantone 11-0105-TPX covering the floors of both labs. The material used is to
have a compressive strength over 50 N/mm² and a bond strength over 1.5
N/mm²; price shall include, supply and install a 45 degree cement angle ()تفنينة
3.7 M.S. 151.00 $ -
surrounding the lab. The cement angle is to be covered with an anti-microbial
and anti-fungal epoxy material with pantone 11-0105-TPX, with felxural
strength of 40N/mm² and tensile strength of 20N/mm².
Supply and install Kitchen wall and base cabinets for ground floor PIEFZA
Office as shown on drawings Sheet no. KTC01. Price to include wooden works,
4.2 L.S. 1.00 $ -
ironmongery as per details and drawings. All accessories are of high quality,
including self closing drawer closers.
Supply and install Kitchen cabinet for Second floor Cafeteria as shown on
drawings. Price to include wooden works, ironmongery as per details and
4.3 L.S. 1.00 $ -
drawings. All accessories are of high quality, including self closing drawer
closers.
Total of Bill No. 4 $ -
Supply, install and fix Aluminum sheet cladding from (Alcobond- natural
brush 400 or approved equivalent) with 4mm panel thickness composing of 2
layers of 0.5mm aluminum skin thickness and an insulation layer for
withstanding extreme high temperatures; coating shall be PVDF for external,
Internal and canopy including all necessary fixings for main supports
5.3 40x40x2mm galvanized steel tubes and galvanized screws, fittings, sealant, M.S. 200.00 $ -
thermal isolation and accessories needed for completing thr works in
accordance to specifications and Engineer's approval. Price shall include
submission of detailed shop drawing and color sample selection for approval
by Engineer.
Supply and install fiber glass board for all shafts at the roof top, price to
include steel frame 3x3 cm tube for beams and columns connected to each
other with special welding with three coats of painting (hammer paint), fiber
5.7 glass board 10mm fixed to the steel tube with special bolts and all necessary L.S. 4.00 $ -
works to do the job in the best way. Contractor is required to submit material
submittal along with shop drawing for review and approval.
Supply and install gypsum boards 12mm for internal beams above
doors/walls SD2, DW5, SD4, SD5, SD6, SD8, SD9, SD10, SD11 and SW1 with
depth ranging between 120cm to 140cm depending on door/wall height;
price include fixation to the wall by a 5x7x0.1cm steel tubes and ceiling by a
6.2-b galvanized steel tubes 5*7*0.1cm at 1.0 meter intervals for beams to columns L.M. 55.00 $ -
supporting the gypsum boards, price include all accessories and bolts and
according to drawings. Price to also include painting 2 coats of complete
putty and 2 coats of mat emlusion paint from APC Paints or equivalent with
color# IT94-1.
Total of Bill No. 6 $ -
Door DW1:
Supply & Fix A 1.10m x 2.22m x 5.00cm solid core wood door. The frame of
the door is a 5.00cm galvanized steel frame with the core of the door being a
4.00cm MDF. The MDF boards are covered with 5mm white oak veneers from
all side. The handles of the door are 90cm in height and 0.19 radius made of
7.1-a stainless steel. All steel work to have a RGB 22 18 19 colour. Please refer to No. 23.00 $ -
the door schedule attached for full dimensions and specifications. Samples of
the wood and steel materials are to be supplied by the contractor to be
approved prior to the commencement any purchases or construction work in
relation to this item. A Shop drawing demonstrating the Door’s connection
with other structural components should be submitted to the Supervising
Engineer for prior approval
Door DW2:
Supply & Fix W2: A 1.70m x 2.22m x 5.00cm solid core wood door consisting
of two parts, each being a 0.8m x 2.22m x 5.00cm . The frame of the door is a
5.00cm galvanized steel frame with the core of the door being a 4.00cm MDF.
The MDF boards are covered with 5mm white oak veneers from all side. The
Door will have 8 openings, 4 on each side, consisting of 5mm clear glass
7.1-b No. 7.00 $ -
surrounded by 0.5cm galvanized steel. The handles of the door are 90cm in
height and 0.19 radius made of stainless steel. All steel work to have a RGB 22
18 19 colour. Please refer to the door schedule attached for full dimensions
and specifications. Samples of the wood and steel materials are to be
supplied by the contractor to be approved prior to the commencement any
purchases or construction work in relation to this item. A Shop drawing
demonstrating the Door’s connection with other structural components
should be submitted to the Supervising Engineer for prior approval
Door DW3:
Supply & Fix W2: A 1.00m x 2.00m x 5.00cm solid core wood door. The frame
of the door is a 5.00cm galvanized steel frame with the core of the door being
a 4.00cm MDF. The MDF boards are covered with 5mm white oak veneers
from all side. The Door will have 4 openings consisting of 5mm clear glass
7.1-c surrounded by 0.5cm galvanized steel. The handles of the door are 90cm in No. 3.00 $ -
height and 0.19 radius made of stainless steel. All steel work to have a RGB 22
18 19 colour. Please refer to the door schedule attached for full dimensions
and specifications. Samples of the wood and steel materials are to be
supplied by the contractor to be approved prior to the commencement any
purchases or construction work in relation to this item. A Shop drawing
demonstrating the Door’s connection with other structural components
should be submitted to the Supervising Engineer for prior approval
Door DW4:
Supply & Fix W2: A 1.10m x 2.20m x 5.00cm solid core wood door. The frame
of the door is a 5.00cm galvanized steel frame with the core of the door being
a 4.00cm MDF. The MDF boards are covered with 5mm white oak veneers
from all side. The Door will have 4 openings consisting of 5mm clear glass
7.1-d surrounded by 0.5cm galvanized steel. The handles of the door are 90cm in No. 1.00 $ -
height and 0.19 radius made of stainless steel. All steel work to have a RGB 22
18 19 colour. Please refer to the door schedule attached for full dimensions
and specifications. Samples of the wood and steel materials are to be
supplied by the contractor to be approved prior to the commencement any
purchases or construction work in relation to this item. A Shop drawing
demonstrating the Door’s connection with other structural components
should be submitted to the Supervising Engineer for prior approval
Door SD3
Supply & Install A 1.00mx 2.20m x 1.20cm monotholic temprered glass door.
The handle of the door is 90cm in height and 0.19 radius made of stainless
steel. The door has 3 40.00cm x 1.00m Vinyl Oracle strips with thickness of
0.06mm with color RGB 93, 188, 210. Please refer to the door schedule
7.2-c No. 2.00 $ -
attached for full dimensions and specifications. Sample of the material are to
be supplied by the contractor to be approved prior to the commencement
any purchases or construction work in relation to this item. All glass door
accessories shall be Italian made and of high quality or equivalent.
Door SD4:
Supply & Install A 1.95mx 2.20m x 1.20cm monotholic temprered glass door.
The handle of the door is 90cm in height and 0.19 radius made of stainless
steel The door has 3 40.00cm x 1.95m Vinyl Oracle strips with thickness of
0.06mm with color RGB 93, 188, 210. Please refer to the door schedule
7.2-d No. 1.00 $ -
attached for full dimensions and specifications. Sample of the material are to
be supplied by the contractor to be approved prior to the commencement
any purchases or construction work in relation to this item. All glass door
accessories shall be Italian made and of high quality or equivalent.
Door SD6:
Supply & Install A 6.47mx 2.00m x 1.2cm monotholic temprered glass door
and two sidelites. The door is a 1.00m x 2.00m x 1.20cm monotholic
temprered glass door. The handle of the door is 90cm in height and 0.19
radius made of stainless steel. The first sidelite is a 1.20m x 2.00m x 1.20cm
monotholic temprered glass. The second sidelite is a 4.27 x 2.00m x 2.50cm
monotholic temprered glass. The door and sidelites have 3 40.00cm x 6.47m
7.2-f No. 1.00 $ -
Vinyl Oracle strips with thickness of 0.06mm with color RGB 93, 188, 210.
Please refer to the door schedule attached for full dimensions and
specifications. Sample of the material are to be supplied by the contractor to
be approved prior to the commencement any purchases or construction work
in relation to this item. All glass door accessories shall be Italian made and of
high quality or equivalent.
Door SD8:
Supply & Install A 10.13m x 2.20m x 1.20cm monotholic temprered glass door
and sidelites. The door is a 1.00m x 2.00m x 1.20cm monotholic temprered
glass. The handle of the door is 90cm in height and 0.19 radius made of
stainless steel. The first sidelite is a 0.30m x 3.60m x 1.20cm monotholic
temprered glass. The second sidelite is a 4.43m x 3.60m x 1.20cm monotholic
temprered glass. The door and sidelites have 3 40.00cm x 5.73m Vinyl Oracle
7.2-g No. 1.00 $ -
stripa with thickness of 0.06mm with color RGB 93, 188, 210. Please refer to
the door schedule attached for full dimensions and specifications. Sample of
the material are to be supplied by the contractor to be approved prior to the
commencement any purchases or construction work in relation to this item.
All glass door accessories shall be Italian made and of high quality or
equivalent.
Door SD9:
Supply & Install A 4.66m x 2.20m x 1.20 cm monotholic temprered glass door
and sidelites. The door is a 1.00m x 2.00m x 5.00cm monotholic temprered
glass door. The handle of the door are 90cm in height and 0.19 radius made
of stainless steel. The first sidelite is a 0.25m x 3.60m x 1.20cm monotholic
temprered glass. The second sidelite is a 3.41 x 3.60m x 1.20cm monotholic
temprered glass. The door and sidelites have 3 40.00cm x 4.66m Vinyl Oracle
7.2-h No. 1.00 $ -
strips with thickness of 0.06mm with color RGB 93, 188, 210. Please refer to
the door schedule attached for full dimensions and specifications. Sample of
the material are to be supplied by the contractor to be approved prior to the
commencement any purchases or construction work in relation to this item.
All glass door accessories shall be Italian made and of high quality or
equivalent.
Door SD10:
Supply & Install A 5.73m x 2.20m x 1.20 cmmonotholic temprered glass door
and sidelites. The door is a 1.00m x 2.00m x 2.50cm monotholic temprered
glass door. The handle of the door are 90cm in height and 0.19 radius made
of stainless steel. The first sidelite is a 0.86m x 3.60m x 1.20cm monotholic
temprered glass. The second sidelite is a 4.43 x 3.60m x 1.20cm monotholic
temprered glass. The door and sidelites have 3 40.00cm x 5.73m Vinyl Oracle
7.2-i No. 1.00 $ -
strips with thickness of 0.06mm with color RGB 93, 188, 210. Please refer to
the door schedule attached for full dimensions and specifications. Sample of
the materials are to be supplied by the contractor to be approved prior to the
commencement any purchases or construction work in relation to this item.
All glass door accessories shall be Italian made and of high quality or
equivalent.
Wall SW1:
Supply & Install A 3.95m x 2.20m x 1.20cm monotholic temprered glass wall.
Please refer to the door schedule attached for full dimensions and
specifications. The wall has 3 40.00cm x 3.95m Vinyl Oracle strips with
7.2-k thickness of 0.06mm with color RGB 93, 188, 210. Sample of the materials No. 1.00 $ -
are to be supplied by the contractor to be approved prior to the
commencement any purchases or construction work in relation to this item.
All glass door accessories shall be Italian made and of high quality or
equivalent.
7.3 Steel Doors
Supply and Fix Prefabricated Fire Rated Steel Doors as per drawings,
specification and instructions of supervisor engineer. Price to include frame,
fixing completely by casting concrete, ironmongery, cylinders, cylindrical
locks handles (Approved by Palestine Standards Institution). 6 mm. glazing,
7.3-a No. 2.00 $ -
gaskets, The doors shall be oven Painted. Steel Door Type DS1. (100 * 210)
cm. All accessories shall be European source of high quality. Galvanized steel
base layer and frame shall be hammer finish.
Supply and Fix Prefabricated Fire Rated Steel Emergency Doors Double Leaf as
per drawings, specification and instructions of supervisor engineer. Price to
include emergency push bar, door closer, frame, fixing completely by casting
concrete, ironmongery, cylinders, cylindrical locks handles (Approved by
7.3-b Palestine Standards Institution). 6 mm. glazing, gaskets, The doors shall be No. 4.00 $ -
oven painted. Steel Door Type DS2. (140 * 210) cm. All accessories shall be
European source of high quality. Galvanized steel base layer and frame shall
be hammer finish.
WC5:
Manufacture and supply a 2.40m x 2.54m Roller Cotton Thermal Shades. The
color of the shades is Pantone 11-0602 TCX and an R-Value between R-4 and
9.1-e R-5 with velco strip closures. Openness Factor is Approx. 5%, the composition No. 1.00 $ -
is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV Bloackage is Approx.
%95, Color Fastness is Class 4.5, and Fire Resistance NFPA701 (USA).
WC6:
Manufacture and supply a 90.00cm x 2.54m Roller Cotton Thermal Shades.
The color of the shades is Pantone 11-0602 TCX and an R-Value between R-4
9.1-f and R-5 with velco strip closures. Openness Factor is Approx. 5%, the No. 1.00 $ -
composition is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV
Bloackage is Approx. %95, Color Fastness is Class 4.5, and Fire Resistance
NFPA701 (USA).
WC7:
Manufacture and supply four 2.00m x 3.60m Roller Cotton Thermal Shades.
The color of the shades is Pantone 11-0602 TCX and an R-Value between R-4
9.1-g and R-5 with velco strip closures. Openness Factor is Approx. 5%, the No. 4.00 $ -
composition is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV
Bloackage is Approx. %95, Color Fastness is Class 4.5, and Fire Resistance
NFPA701 (USA).
WC8:
Manufacture and supply a 3.00m x 2.54m Roller Cotton Thermal Shades. The
color of the shades is Pantone 11-0602 TCX and an R-Value between R-4 and
9.1-h R-5 with velco strip closures. Openness Factor is Approx. 5%, the composition No. 1.00 $ -
is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV Bloackage is Approx.
%95, Color Fastness is Class 4.5, and Fire Resistance NFPA701 (USA).
WC9:
Manufacture and supply two 1.80m x 3.6m Roller Cotton Thermal Shades.
The color of the shades is Pantone 11-0602 TCX and an R-Value between R-4
9.1-i and R-5 with velco strip closures. Openness Factor is Approx. 5%, the No. 2.00 $ -
composition is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV
Bloackage is Approx. %95, Color Fastness is Class 4.5, and Fire Resistance
NFPA701 (USA).
WC11:
Manufacture and supply a 1.31m x 2.54m Roller Cotton Thermal Shades. The
color of the shades is Pantone 11-0602 TCX and an R-Value between R-4 and
9.1-k R-5 with velco strip closures. Openness Factor is Approx. 5%, the composition No. 1.00 $ -
is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV Bloackage is Approx.
%95, Color Fastness is Class 4.5, and Fire Resistance NFPA701 (USA).
WC12:
Manufacture and supply ten 1.00m x 2.54m Roller Cotton Thermal Shades.
The color of the shades is Pantone 11-0602 TCX and an R-Value between R-4
9.1-l and R-5 with velco strip closures. Openness Factor is Approx. 5%, the No. 10.00 $ -
composition is 30% Polyester and 70% PVC, Thickness is 0.64±%5, UV
Bloackage is Approx. %95, Color Fastness is Class 4.5, and Fire Resistance
NFPA701 (USA).
Total of Bill No. 9 $ -
Contractor: -------------------------------------------------------------
Date: --------------------------------------------------------------