Академический Документы
Профессиональный Документы
Культура Документы
F r e e
Record of Revision
Version Data Page. Old Description New Description Remark
1.0 2007/03/07 First release N/A N/A
1.1 2007/04/09 6 IDD=1.08A(typ),1.2A(max) IDD=1.35A(typ),1.5A(max)
6 Pc=13W(typ),15.84W(max) Pc=16.2W(typ),19.8W(max)
* General Information
Items Specification Unit Note
Active Screen Size 46 inches Diagonal
Display Area 1018.08(H) x 572.67(V) mm
Outline Dimension 1083.0(H) x 627.0(V) x 50.6(D) mm With Balance Board
Driver Element a-Si TFT active matrix
Display Colors 16.7M Colors
Color Gamut 72 % NTSC
Number of Pixels 1920 x 1080 Pixel
Pixel Arrangement RGB vertical stripe
Display Mode Normally Black
Surface Treatment AG, 3H
Note 3: Sine wave, 11ms, direction: ±x, ±y, ±z (one time each direction)
Note 4: Wave form: random, vibration level: 1.5G RMS, Bandwidth: 10--300Hz
Duration: X, Y, Z 30min (one time each direction)
The performance of the Lamp in LCD panel, for example life time or brightness, is extremely influenced
by the characteristics of the balance board and I/P board. All the parameters should be carefully
designed as not to produce too much leakage current from high-voltage output. While design or order
balance board, please make sure unwanted lighting caused by the mismatch of the lamp and balance
board (no lighting, flicker, etc) never occurs. After confirmation, the LCD Panel should be operated in
the same condition as installed in your instrument.
Note:
1. VDD=12.0V, fV=60Hz, fCLK=81.5Mhz, 25°C, VDD duration time=400µs, test pattern: white pattern
2. The backlight power consumption shown above is tested by lamp current IL=6.0mA.
3. The life is determined as the time at which luminance of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25±2°C.
4. VCIM=1.25V
VTH
VCIM
VTL
0V
Vdd
0.9 Vdd
0.1 Vdd
GND
400ms
Clock
RIN0+
R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
RIN0-
RIN1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
RIN1-
RIN2+ B3 B2 DE NA NA B5 B4 B4 B2 DE
RIN2-
RIN3+
R7 R6 NA B7 B6 G7 G6 R7 R6 NA
RIN3-
Clock
RIN0+
R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
RIN0-
RIN1+ G4 G3 B3 B2 G7
G6 G6 G5 G4 G3 B3
RIN1-
RIN2+ B5 B4 DE NA NA B7 B6 B5 B4 DE
RIN2-
RIN3+
R1 R0 NA B1 B0 G1 G0 R1 R0 NA
RIN3-
T460HW02 V1
RGB 768 1 2 3 4 768
Invalid Data Invalid Data
Data Line Line Line Line Line Line
CLK
Tclk
Tdisp(h)
Values
Parameter Unit
Min. Typ. Max.
t1 400 -- 2000 µs
t2 20 -- 50 ms
t3 700 or (200)* -- -- ms
t4 200 -- -- ms
t5 50 -- -- ms
t6 0.47 -- 30 ms
t7 1000 -- -- ms
* If t3=200ms, input black signal till 700ms from system is necessary. In case of t3<200ms, the
abnormal display will be happened. But it will not damage timing controller.
Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal.
Caution: The above on/off sequence should be applied to avoid abnormal function in the display. In
case of handling, make sure to turn off the power when you plug the cable into the input connector or
pull the cable out of the connector.
CN127 CN226
CN125
Master
Slave
I/P Board
CN128 CN227
Specification
Specification
Item Symbol Description Unit Note
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 1500 2000 -- 1
2
Surface Luminance (White) LWH 450 550 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.3 3
Response Time (Average) Tγ -- 8 -- ms 4, 5 (Gray to Gray)
Rise Time Tr -- 15 -- ms
Decay Time Tf -- 5 -- ms
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.290
GY 0.600
Typ.-0.03 Typ.+0.03
Blue BX 0.150
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle (Contrast Ratio>10)
2. Surface Luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all
pixels displaying white. For more information see Fig. 4-2. When lamp current IL=6.0mA, LWH=Lon5, where
Lon5 is the luminance with all pixels displaying white at center 5 location.
V/2 1 2 3
4 5 6 V
7 8 9
V/6
H/6 H/2
3. The variation in surface luminance, δWHITE(9P) is defined under brightness of IL=6.0mA as:
δWHITE(9P) = Maximum(Lon1, Lon2,…,Lon9)/Minimum(Lon1, Lon2,…Lon9)
4. Response time is the time required for the display to transition from white(L255) to black(L0) (Decay
Time, Tf=TrD), and from black(L0) to white(L255) (Rise Time, Tr=TrR). For additional information see Fig.
4-3.
TrD TrR
L0,15,L31,….L255 L0,15,L31,….L255
100%
90%Luminance
10%
L0,15,L31,….L255
0%
Time
TrD TrR
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for
the horizontal (or x-axis) and the vertical (or y-axis) with respect to the z-axis which is normal to the LCD
surface. For more information see Fig. 4-5.
6-2. EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC), 1998
Module
1pcs Module/ESD Bag
Cushion set
Cushion top
6pcs Modules
Cushion down
"H" Tape
6pcs / 1 carton
8-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they be
stored in the container in which they were shipped.