Академический Документы
Профессиональный Документы
Культура Документы
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Inputs
POWER OUTPUT AND TOTAL HARMONIC Input jacks INPUT: input pin jack
DISTORTION: SPEAKER IN: input terminals
Output jacks SPEAKER OUT: output terminals
With 6 ohm loads, from 28 – 200 Hz; rated 100 watts,
minimum RMS power, with no more than 0.8 % total General
harmonic distortion from 250 milliwatts to rated Power requirements Taiwan models: 110 V AC, 50 Hz
output. USA and Canada models: 120 V AC, 60 Hz
Other models: 230 V AC, 50/60 Hz
System Power consumption 100 W
Type Active Subwoofer (magnetically shielded design) Dimensions Approx. 290 × 355 × 387 mm
Speaker unit Woofer: 20 cm dia. (8 in.), cone type (11 3/8 × 14 × 15 1/4 in.) (w/h/d)
RMS output 100 W (6 Ohms, 40 Hz, 10% THD) Mass 11.5 kg (25 lb 6 oz)
Frequency range 28 Hz – 200 Hz Supplied accessories Foot pads (4)
High frequency cut-off frequency Audio connecting cord (1 phono – 1 phono),
50 Hz – 200 Hz 2 m (6 ft 6 1/2 in.) (1)
Phase selector NORMAL, REVERSE Speaker cords, 2.5 m (8 ft 2 1/2 in.) (2)
ACTIVE SUBWOOFER
9-877-696-01 Sony Corporation
2004C04-1 Home Audio Company
© 2004.03 Published by Sony Engineering Corporation
1
SA-WM250
To Exposed Metal
Parts on Set
AC
• UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
0.15 µF 1.5 k Ω voltmeter
(0.75 V)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
2
SA-WM250
SECTION 1 SECTION 2
GENERAL This section is extracted DIAGRAMS
from instruction manual.
LOCATION OF CONTROL 2-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
R R
L L
IN OUT
SPEAKER
L L
For schematic diagrams. For printed wiring boards.
IN OUT
SPEAKER
SPEAKER IN R R R R Note: Note:
IN OUT
SPEAKER
Front Speaker (R) Front Speaker (L)
Front Speaker (R) Front Speaker (L)
IN OUT
SPEAKER
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
This subwoofer This subwoofer
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • : Pattern from the side which enables seeing.
• All resistors are in Ω and 1/4 W or less unless otherwise • Abbreviation
D E F G specified. CND : Canadian model.
1 2
Amplifier
This subwoofer POWER indicator
• f : internal component. MY : Malaysia model.
120Hz 150Hz
• C : panel designation.
MONO OUT
SP : Singapore model.
PHASE
INPUT NORMAL 2 1
REVERSE PHASE 200Hz
100Hz
CUT OFF FREQ
200Hz 3 50Hz
75Hz
4
Foot pads
Note: Note:
POWER 50Hz
L L
MIN
R R
cal for safety. Ne les remplacer que par une
IN OUT
Replace only with part piéce por tant le numéro
LEVEL number specified. spécifié.
• A : B+ Line.
• B : B– Line.
Connecting to an amplifier with a • Voltages are dc with respect to ground under no-signal
Precautions Hooking Up the System special jack for a subwoofer Adjusting the Sound (F) (detuned) conditions.
If your amplifier has a special jack for a subwoofer (such
On safety Overview as MONO OUT jack, MIX OUT jack, SUBWOOFER jack You can adjust the sound of the subwoofer to suit the
sound of your front speakers. Reinforcing the bass sound
no mark : Power on
Use the INPUT jacks or the SPEAKER IN terminals of the or SUPER WOOFER jack), connect the INPUT jack of the
• Before operating the subwoofer, be sure that the
operating voltage of your subwoofer is identical with
subwoofer when you connect the amplifier. subwoofer to one of those jacks. gives you a greater sense of atmosphere. • Voltages are taken with a VOM (Input impedance 10 MΩ).
• If your amplifier has one of the following types of
that of your local power supply.
output jacks, connect the INPUT jack and the
Hookups (D)
1 Adjust the cut-off frequency. Voltage variations may be noted due to normal produc-
• Unplug the subwoofer from the wall outlet if it is not to amplifier's jack using the supplied audio connecting Connect the MONO OUT jack of your amplifier to the
be used for an extended period of time. To disconnect cord. INPUT jack of the subwoofer with the supplied audio Turn the CUT OFF FREQ control, depending tion tolerances.
the cord, pull the cord by grasping the plug. Never connecting cord. on the reproduction frequencies of your front
pull the cord itself.
— MONO OUT jack
speakers. • Signal path.
— MIX OUT jack Note
• Should any liquid or solid object fall into the
subwoofer, unplug the subwoofer and have the — SUBWOOFER output jack(s) If the output level of your amplifier is not large enough,
Refer to the following when adjusting. F : AUDIO
the sound may not be loud enough. In this case, connect 1 Typical very small sized speakers: 5 – 7 cm
subwoofer checked by qualified personnel before
operating it any further.
— SUPER WOOFER output jack(s)
the speaker terminals of the amplifier directly to the dia. • Abbreviation
• AC power cord must be changed only at the qualified • If your amplifier does not have the above mentioned SPEAKER IN terminals of the subwoofer. 2 Typical small sized speakers: 8 –15 cm dia. CND : Canadian model.
service shop. output jacks, connect the speaker terminals of the 3 Typical medium sized speakers: 16 –24 cm
When turning on or off an amplifier or other
amplifier to the SPEAKER IN terminals instead. (A) Connecting the AC power cord dia. MY : Malaysia model.
• Connect the AC power cord from the subwoofer and
equipment
Before you get started from your amplifier to a wall outlet. 4 Typical large sized speakers: more than 25 SP : Singapore model.
Lower the volume of the amplifier to minimum. • Make sure that power to the subwoofer is turned off cm dia.
• Turn off the power of the amplifier and the subwoofer
before making any connection. before you plug in or unplug any power cord. To make the most of the low level converter
TW : Taiwan model.
To avoid damaging the subwoofer
• Use the audio connecting cords that are supplied to function of Dolby digital, turn the CUT OFF
• Be careful in setting the volume control of the amplifier FREQ as high as possible when playing back
the respective equipment. If there are not enough
to avoid an excessive input power.
• Do not attempt to open the enclosure or remold
audio connecting cords to make the necessary Listening to the Sound (E) the Dolby digital.
connections, you need to purchase some optional
speaker units and networks.
audio connecting cords. 2 Adjust the volume level of the subwoofer.
• Be sure to make connections firmly to avoid noise.
In case color irregularity is observed on the
• Connect the AC power cord from the subwoofer to
1 Turn on the amplifier and select the program Turn the LEVEL control so that you can hear
nearby TV screen the bass sound a little more than before. To
source.
With the magnetically shielded type of the speaker a wall outlet.
• You cannot connect the CENTER output jack for use
increase the volume, turn the LEVEL control 2-2. CIRCUIT BOARDS LOCATION
system, the speakers can be installed near a TV set. clockwise. To reduce the volume, turn the
However, color irregularity may still be observed on the with Dolby Pro Logic function to the subwoofer. 2 Press POWER.
LEVEL control counterclockwise.
TV screen depending on the type of your TV set. Bass sound is not output with some Dolby Pro Logic
The subwoofer turns on and the POWER
modes.
If color irregularity is observed... indicator lights up in green. 3 Play your favorite song and movie.
t Turn off the TV set once, then turn it on after 15 to Male vocal tunes and voice containing bass
INPUT CONTROL board
Connecting to an amplifier with a 3 Play the program source.
30 minutes. sounds are most suitable for adjustment.
single set of speaker terminals (B) Turn the volume for front speakers to the
If color irregularity is observed again... If your amplifier is equipped with a single set of speaker Adjust the VOLUME so that sound from the
front speakers is not distorted. same level as usual.
t Place the speakers further apart from the TV set. terminals, connect the subwoofer to the amplifier, and
then connect the front speakers to the subwoofer. If it is distorted, the sound from the
When howling occurs subwoofer will also be distorted. 4 Select the phase polarity.
Relocate the speaker or turn down the volume of the Hookups
Use the PHASE selector to select the phase
amplifier.
polarity.
On installation 1 Connect the subwoofer to the amplifier.
Notes
• Do not install the subwoofer near heat sources such as Connect the SPEAKER IN terminals of the • Never set the amplifier’s tone control (BASS, TREBLE, 5 Repeat steps 1 to 4 to adjust for your MAIN board
radiators or air ducts, or in a place subject to direct subwoofer to the amplifier’s speaker etc.) or the equalizer output to a high level or input preference.
sunlight, excessive dust, mechanical vibration or shock. terminals with the speaker cords. Be sure to sinewaves of 20 Hz to 50 Hz recorded on a Once you have adjusted the subwoofer to the
• Good ventilation is essential to prevent internal heat connect both L and R channels. commercially-available test disc or special sound (bass settings you want, use the VOLUME control CONTROL board
build-up in the subwoofer. Place the subwoofer in a sound of electronic musical instrument, pop noise of on the amplifier to adjust the volume of the
location with adequate air circulation. Do not place the
subwoofer on a soft surface.
2 Connect the front speakers to the subwoofer. analog disc turntable, sound with abnormally subwoofer with that of the other speakers.
enhanced bass, etc.) in a high level to this unit. These You don’t need to adjust the subwoofer
• Use caution when placing the speaker on a specially Connect the speakers to the SPEAKER OUT actions may cause damage to the speakers.
terminals of the subwoofer. settings when you change the volume level
treated (waxed, oiled, polished, etc.) floor, as staining When a special disc containing abnormally enhanced
or discoloration may result.
of the amplifier.
bass is played, noise may be output in addition to the
original sound. In such a case, reduce the sound level.
On cleaning the cabinet
Clean the cabinet with a soft cloth lightly moistened with Connecting to an amplifier with • The subwoofer output signal (DOLBY digital signal)
of the digital surround processor sold singularly is set
POWER TRANS board
water. Do not use any type of abrasive pad, scouring double (A+B) sets of speaker Notes
10 dB higher by Dolby laboratories Licensing
powder or solvent such as alcohol or benzine. terminals (C) Corporation. In the case of using normally, adjust the • If the sound distorts when you turn on the bass
If your amplifier has double (A+B) sets of speaker subwoofer level. reinforcement from your amplifier (such as, DBFB,
If you have any questions or problems concerning your terminals, connect both the subwoofer and the front GROOVE, the graphic equalizer, etc.), turn off the bass
subwoofer that is not covered in this manual, please speakers to the amplifier. reinforcement and adjust the sound.
consult your nearest Sony dealer. • Do not turn the volume of the subwoofer to maximum.
Hookups Doing so may weaken the bass sound. Moreover,
extraneous noise may be heard.
1 Connect the front speakers to the amplifier. • Selecting NORMAL or REVERSE with the PHASE
selector reverses the polarity and may provide better
Installation Connect the speakers to your amplifier’s bass reproduction in certain listening environments
SPEAKER A terminals. (depending on the type of front speakers, the position
Since the human ear cannot detect the direction and
of the subwoofer and the adjustment of the cut-off
position where the bass sound being reproduced by a
frequency). It may also change the expanse and
subwoofer (below 200 Hz) comes from, you can install 2 Connect the subwoofer to the amplifier.
tightness of sound, and effect the feeling of the sound
the subwoofer wherever you like in your room. To
Connect the SPEAKER IN terminals of the field. Select the setting that provides the sound you
obtain a better bass reproduction, we recommend you
subwoofer to the amplifier’s SPEAKER B prefer when listening in your normal listening position.
to install the subwoofer on a solid floor where the
resonance is unlikely to occur. terminals using the supplied speaker cords.
Setting the speaker (G)
To prevent speaker vibration or movement while
Notes listening, attach the supplied foot pads to the speaker.
When using the double (A+B) sets of speakers, make
• Always install the subwoofer vertically, keeping a few sure that you select the “A+B” position with your
centimeters away from the wall. amplifier.
• Do not place an object on the subwoofer or sit on it.
• If the subwoofer is installed in the center of a room, the Note
bass could be extremely weakened. This is due to the When you are using SPEAKER A terminal (front
influence of the standing wave of the room. If this speaker) only or when the power of the amplifier is
happens, move the subwoofer away from the center of turned off, turn down the volume or turn off the power SWITCH board
a room or eliminate the cause of the standing wave, by of the subwoofer. Otherwise, hum noise may be heard.
installing a bookshelf on the wall, etc.
3 3
SA-WM250
2-3. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 3 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
(Page 6) (Page 6) (Page 5) (Page 5)
RV801
R501
C801
B
C210
C601
D602
CN402 R404 JW132
C501
Q503
Q504
JW112
G2
Q501
C502
JW122
CN301
R211
D501
C411 C402 R217 CNP801
R403
C503
JW131
C401 R317 R508
C410
C211
R312
JW130
D403
R502
R503
D401 JW121
Q502
D402
D304
R505
C409
C203
C318
C204
R210
C
JW123
JW103
R601 JW120
JW124 R208
C205 C206
RY301 C209
JW125
JW104
JW101
R216
JW404
R311
JW119
D JW135 R207
R504
JW118
JW117
R215
C317
C316
R205
R301
JW108
C310
JW107
JW106
JW105
JW127
JW110
JW109
C404
C314
C403
E JW111
JW114
JW129
R310
R314 C309
JW102
C308
R302
C304
C305 C306 R308
C301
C303
JW115
R304
JW116
C307
JW301
JW126
C302
R507
R401 R305
R306
R309
F
R402
R313
R315
C312 C313
JW501
R303 C311 R307
D502
C405 C406
IC301
R506
Q505
D302
D301 JW128
• Semiconductor
Location
Ref. No. Location
D205 D-8
D206 D-8
D301 F-4
D302 F-4
D304 C-6
D401 C-3
D402 C-4
D403 C-4
D501 B-5
D502 F-4
D602 B-8
IC202 D-9
IC203 D-10
IC301 F-7
Q501 B-6
Q502 C-6
Q503 B-7
Q504 B-7
Q505 F-4
4 4
SA-WM250
2-4. PRINTED WIRING BOARD — INPUT CONTROL SECTION — • Refer to page 3 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
(Page 4) (Page 4)
B C703 R701
JW702 R203
JW209
R703 CN101
JW207 R204
R702 CN701
JW210
D203
D201
C705 IC201
JW208
JW204
D204
C
D202
JW205
C702
R202
R201
JW206
RV701
IC701 R705
C704
R704 C701
JW701
R109
R103
C706
D R102 R104
R108
J101 C201 R107
R706
R707
R106
R708
R105
R101
R110
C101
S701 TM101
• Semiconductor
Location
Ref. No. Location
D201 C-12
D202 C-12
D203 C-11
D204 C-12
IC201 C-10
IC701 C-2
5 5
SA-WM250
2-5. PRINTED WIRING BOARDS — POWER SECTION — • Refer to page 3 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
(Page 4)
B CNP401
(Page 4)
CN901
FH951
G
C2 JW1
CN3
C901
CN2
H
FH901
JW2
6 6
SA-WM250
2-6. SCHEMATIC DIAGRAM — MAIN SECTION — • Refer to page 8 for IC Block Diagram.
TM101 R102
D202
D201
R101 R104
S701
IC201(2/2)
R103 RV701
IC701(2/2)
R105
R204 R208
D203
D204
R106
R701 IC701(1/2)
IC201(1/2) R702
R108 C203 C204 C704 R708
C701
C706
R207
R107
C702
D205
R201 R202 C205 C316
R210
R205
J101
D206
C201 R211 C206 C317
C101 R110
IC203(1/2)
C801
CNP111 CNP801
R216 RV801
R215
C210 IC203(2/2)
C209
IC301
R217 C211
R301 IC B/D
R506
Q505
C312
R308
R306 C313
C302 C308 G2
R507 R303 R304
R309
R302
D301
D302
JW501
R305
C309
C314 R311
D901
C304 C306 C305 RY301
C310 CN301
CN901 CN204 D304
R314
R310
C601 D602 R601 SP901
R317
D401
R401
C405 C403 TW
C401
F901
T1 JW1 CN2 CN3
Q502 R503 R502 C402
C406 C404
R504 C901 S901
Q504 CN402 CNP401
C411
G1
R402
D501
Q503
C502
R505 R501 R500
Q501 CN1
JW403 D402 R403
C407 C409 C412 C2
C501
C503
C408 C410
D403 R404
JW404
7 7
SA-WM250
1 2 3 4 5 6 7 8 9 10 11 12 13
8 8
SA-WM250
SECTION 3
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark 0 or dotted line with mark
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) 0 are critical for safety.
they are seldom required for routine service. R R Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories are given in the last of this
• -XX and -X mean standardized parts, so parts list. Les composants identifiés par une
they may have some difference from the • Abbreviation marque 0 sont critiques pour
original one. CND : Canadian model la sécurité.
MY : Malaysia model Ne les remplacer que par une piéce
SP : Singapore model portant le numéro spécifié.
TW : Taiwan model
supplied with
not supplied 8 RV701 7
(INPUT CONTROL board) #1
7
not supplied
(POWER TRANS board)
supplied with
RV801
not supplied
8 #1
#2
A 8
#2 F901
T901
not supplied
6 (CONTROL board)
#3
5 A
not supplied #2
8
4 #3
#2
not supplied
(MAIN board)
not supplied
SP901
2 not supplied
3
2 1
not supplied
(SWITCH board)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 A-4713-812-A SPEAKER CABINET ASSY (BLACK)...(BLACK) 8 4-235-677-01 SCREW (4X20) (TYPE1), +BVTP
1 A-4715-636-A SPEAKER CABINET ASSY (WOOD)...(WOOD) 0 F901 1-532-463-51 FUSE (T1AL/250V) (AEP,UK,SP,MY)
2 4-229-774-01 SCREW, TAPPING, HEXAGON SOCKET 0 F901 1-533-450-12 FUSE, GLASS TUBE (DIA.5) (2.5A/125V)
3 4-253-174-01 GRILLE FRAME (US,CND,TW)
4 3-905-609-31 SCREW (TRANSISTOR) SP901 1-825-004-13 SPEAKER (20cm) (WOOFER)
0 T901 1-439-624-11 TRANSFORMER, POWER (AEP,UK,SP,MY)
* 5 3-703-244-00 BUSHING (2104), CORD
06 1-769-744-11 CORD, POWER (AEP,UK,SP,MY) 0 T901 1-439-625-11 TRANSFORMER, POWER (US,CND,TW)
06 1-783-820-11 CORD, POWER (US,CND) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
06 1-827-597-41 CORD, POWER (TW) #2 7-685-880-09 SCREW +BVTT 4X6 (S)
7 4-999-482-81 KNOB (VOL) #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
9
SA-WM250
SECTION 4
CONTROL ELECTRICAL PARTS LIST
INPUT CONTROL MAIN
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. Les composants identifiés par une
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. marque 0 sont critiques pour
All resistors are in ohms. • CAPACITORS la sécurité.
METAL:Metal-film resistor. uF : µF Ne les remplacer que par une piéce
METAL OXIDE: Metal oxide-film resistor. • COILS portant le numéro spécifié.
F:nonflammable uH : µH
• Abbreviation
When indicating parts by reference CND : Canadian model TW : Taiwan model
number, please include the board. MY : Malaysia model
SP : Singapore model
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CONTROL BOARD < RESISTOR >
***************
R101 1-260-107-11 CARBON 4.7K 5% 1/2W
< CAPACITOR > R102 1-247-879-11 CARBON 100K 5% 1/4W
R103 1-247-879-11 CARBON 100K 5% 1/4W
C801 1-126-964-11 ELECT 10uF 20% 50V R104 1-247-847-11 CARBON 4.7K 5% 1/4W
R105 1-247-847-11 CARBON 4.7K 5% 1/4W
< CONNECTOR >
R106 1-247-847-11 CARBON 4.7K 5% 1/4W
CNP801 1-691-765-11 PLUG (MICRO CONNECTOR) 3P R107 1-260-107-11 CARBON 4.7K 5% 1/2W
R108 1-247-879-11 CARBON 100K 5% 1/4W
< VARIABLE RESISTOR > R109 1-247-879-11 CARBON 100K 5% 1/4W
R110 1-247-879-11 CARBON 100K 5% 1/4W
RV801 1-227-511-11 RES, VAR, CARBON 20K (LEVEL)
************************************************************* R201 1-247-847-11 CARBON 4.7K 5% 1/4W
R202 1-247-831-11 CARBON 1K 5% 1/4W
INPUT CONTROL BOARD R203 1-247-847-11 CARBON 4.7K 5% 1/4W
******************** R204 1-247-847-11 CARBON 4.7K 5% 1/4W
R701 1-247-847-11 CARBON 4.7K 5% 1/4W
< CAPACITOR >
R702 1-249-429-11 CARBON 10K 5% 1/4W
C101 1-128-813-11 CERAMIC 220PF 5% 50V R703 1-249-428-11 CARBON 8.2K 5% 1/4W
C201 1-126-964-11 ELECT 10uF 20% 50V R704 1-249-428-11 CARBON 8.2K 5% 1/4W
C701 1-126-947-11 ELECT 47uF 20% 35V R705 1-247-879-11 CARBON 100K 5% 1/4W
C702 1-126-947-11 ELECT 47uF 20% 35V R706 1-247-847-11 CARBON 4.7K 5% 1/4W
C703 1-126-963-11 ELECT 4.7uF 20% 50V
R707 1-249-429-11 CARBON 10K 5% 1/4W
C704 1-131-702-11 FILM 0.68uF 5% 50V R708 1-249-429-11 CARBON 10K 5% 1/4W
C705 1-136-157-00 FILM 0.022uF 5% 50V
C706 1-126-965-11 ELECT 22uF 20% 50V < VARIABLE RESISTOR >
< CONNECTOR > RV701 1-227-365-11 RES, VAR, CARBON 20KX2 (CUT OFF FREQ)
10
SA-WM250
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C210 1-126-964-11 ELECT 10uF 20% 50V < GROUND TERMINAL >
C211 1-128-813-11 CERAMIC 220PF 5% 50V
C301 1-128-813-11 CERAMIC 220PF 5% 50V G1 1-537-738-21 TERMINAL, GROUND
C302 1-126-964-11 ELECT 10uF 20% 50V G2 1-537-738-21 TERMINAL, GROUND
C303 1-104-658-11 ELECT 100uF 20% 10V
< IC >
C304 1-126-968-11 ELECT 100uF 20% 50V
C305 1-126-968-11 ELECT 100uF 20% 50V IC202 8-759-636-74 IC M5218AP-22
C306 1-126-964-11 ELECT 10uF 20% 50V IC203 8-759-636-74 IC M5218AP-22
C307 1-126-967-11 ELECT 47uF 20% 50V IC301 6-600-091-01 IC STK404-130S
C308 1-126-964-11 ELECT 10uF 20% 50V
< TRANSISTOR >
C309 1-136-165-00 FILM 0.1uF 5% 50V
C310 1-136-165-00 FILM 0.1uF 5% 50V Q501 8-729-119-78 TRANSISTOR 2SC2785-HFE
C311 1-162-199-31 CERAMIC 10PF 5% 50V Q502 8-729-178-42 TRANSISTOR 2SC2784-F
C312 1-128-813-11 CERAMIC 220PF 5% 50V Q503 8-729-119-78 TRANSISTOR 2SC2785-HFE
C313 1-128-813-11 CERAMIC 220PF 5% 50V Q504 8-729-029-86 TRANSISTOR DTC124ESA
Q505 8-729-119-78 TRANSISTOR 2SC2785-HFE
C314 1-128-813-11 CERAMIC 220PF 5% 50V
C316 1-128-813-11 CERAMIC 220PF 5% 50V < RESISTOR >
C317 1-128-813-11 CERAMIC 220PF 5% 50V
C318 1-128-813-11 CERAMIC 220PF 5% 50V R207 1-249-429-11 CARBON 10K 5% 1/4W
C401 1-136-165-00 FILM 0.1uF 5% 50V R208 1-249-426-11 CARBON 5.6K 5% 1/4W
R210 1-247-871-11 CARBON 47K 5% 1/4W
C402 1-136-165-00 FILM 0.1uF 5% 50V R211 1-247-863-11 CARBON 22K 5% 1/4W
C403 1-104-482-11 ELECT 4700uF 20% 63V R215 1-249-429-11 CARBON 10K 5% 1/4W
C404 1-104-482-11 ELECT 4700uF 20% 63V
C405 1-126-968-11 ELECT 100uF 20% 50V R217 1-247-879-11 CARBON 100K 5% 1/4W
C406 1-126-968-11 ELECT 100uF 20% 50V R301 1-247-847-11 CARBON 4.7K 5% 1/4W
R302 1-247-871-11 CARBON 47K 5% 1/4W
C407 1-126-971-11 ELECT 470uF 20% 50V R303 1-249-413-11 CARBON 470 5% 1/4W
C408 1-126-971-11 ELECT 470uF 20% 50V 0 R304 1-215-886-11 METAL OXIDE 100 5% 2W F
C409 1-136-165-00 FILM 0.1uF 5% 50V
C410 1-136-165-00 FILM 0.1uF 5% 50V R305 1-247-871-11 CARBON 47K 5% 1/4W
C411 1-128-813-11 CERAMIC 220PF 5% 50V R306 1-247-847-11 CARBON 4.7K 5% 1/4W
R307 1-247-847-11 CARBON 4.7K 5% 1/4W
C412 1-128-813-11 CERAMIC 220PF 5% 50V 0 R308 1-234-182-11 ENCAPSULATED COMPONENT 0.22X2 5W
C501 1-126-964-11 ELECT 10uF 20% 50V R309 1-249-409-11 CARBON 220 5% 1/4W
C502 1-126-949-11 ELECT 220uF 20% 35V
C503 1-126-923-11 ELECT 220uF 20% 10V R310 1-249-393-11 CARBON 10 5% 1/4W
C601 1-126-964-11 ELECT 10uF 20% 50V R311 1-215-868-00 METAL OXIDE 680 5% 1W
R312 1-247-863-11 CARBON 22K 5% 1/4W
< CONNECTOR > R313 1-249-429-11 CARBON 10K 5% 1/4W
0 R314 1-217-637-00 FUSIBLE 1 5% 1/4W F
CN201 1-784-931-11 PIN, CONNECTOR 5P
CN202 1-779-179-11 CONNECTOR (B5B-XH-A) 5P R315 1-247-871-11 CARBON 47K 5% 1/4W
* CN204 1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P R317 1-249-393-11 CARBON 10 5% 1/4W
CN301 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P 0 R401 1-215-891-11 METAL OXIDE 680 5% 2W F
CN402 1-785-104-11 PIN, CONNECTOR (3.96mm PITCH) 6P 0 R402 1-215-891-11 METAL OXIDE 680 5% 2W F
0 R403 1-219-153-11 FUSIBLE 10 5% 1/4W F
CNP111 1-691-765-11 PLUG (MICRO CONNECTOR) 3P
0 R404 1-219-153-11 FUSIBLE 10 5% 1/4W F
< DIODE > R500 1-249-421-11 CARBON 2.2K 5% 1/4W
R501 1-249-429-11 CARBON 10K 5% 1/4W
D205 8-719-110-31 DIODE RD12ESB2 R502 1-247-871-11 CARBON 47K 5% 1/4W
D206 8-719-110-31 DIODE RD12ESB2 R503 1-247-879-11 CARBON 100K 5% 1/4W
D301 8-719-991-33 DIODE 1SS133T-77
D302 8-719-991-33 DIODE 1SS133T-77 R504 1-247-879-11 CARBON 100K 5% 1/4W
D304 8-719-991-33 DIODE 1SS133T-77 R505 1-247-863-11 CARBON 22K 5% 1/4W
R506 1-247-863-11 CARBON 22K 5% 1/4W
D401 8-719-302-38 DIODE RBV-602-01 R507 1-247-847-11 CARBON 4.7K 5% 1/4W
D402 6-500-522-11 DIODE 10EDB40-TA2B5 R508 1-247-831-11 CARBON 1K 5% 1/4W
D403 6-500-522-11 DIODE 10EDB40-TA2B5
D501 8-719-991-33 DIODE 1SS133T-77 0 R601 1-215-920-11 METAL OXIDE 3.3K 5% 3W F
D502 8-719-991-33 DIODE 1SS133T-77
< RELAY >
D602 8-719-991-33 DIODE 1SS133T-77
RY301 1-515-920-11 RELAY (24V)
*************************************************************
MISCELLANEOUS
***************
MEMO
13
SA-WM250
REVISION HISTORY
14