~ ANDREWS FASTENERS LIMITED - TECHNICAL GUIDE, é
NON PRE LOAD FASTENERS.
BS 4395 (HSFG) has been replaced by BSEN 14399,referred to as PRELOAD. | BSEN 15048 ixreplacing previous general grade fastener standards. SB refers
MARKINGS ——-HRS.8= Similar 10 HSEG Paw LOAD CSK, Arms | Thichnew
HR 10.9=Similarto HSFG Part2 Storted Boks ieas)| mes
ssasspart | nsen oe 150 [DIN| 150]
ONEUISEG) | L399 HRA a Te} To
inate 2s) 1a]
Tak 3e_[ism)215|
200K a [2z0)234)
BikS Msepse-[ $5 [3901510]
week MIN, PLATING THICKNES
Css BRIGHT ZINC PLATED Cr3-SUM
GALVANIZING- 40M,
eee SHERARDIZED- 30 UM CLASS 1 OR IS UM CLASS?
: ‘At ‘Trade Mark| SQ SQ Bolts, Fullnuts, Washers
rotrusions || Dia. | bond (form A-G), Plate Washers and 2
eiceaestenees | [ry Win Coneecan te
weseeepned [pane rae
Smicitewees” REE ES Dia [SQSQ Wel Thread Leng]
ort 893) Soe we it e132
arama wd I radenary RET Hau) 130-273
ae Tormsure redone |r sis
Patned ron Pete eee Mio) 1301405
Sof si i 0-138
‘igrRucTions Fon nsTALLING DIRECT TENSION
WipieaToRS Rice FoRUSEWweNPRECoAS" | NONUTORBOLTFACE WASHERS
(are) Pasrenens REQUIRED WITIHTURNASURE DTI
USEA0.40 MM FELER GAUGE
IFTHE DTUISAT THE OPPOSITE
END TO THE ROTATED PART.
OTHERWISE 40.25 MM FEE
GAUGE MUSTRE USED.
“TALLOW MUST BE USED ON PLATED PARTS (buy fallow at y:n.monument-tools.com)
CONTACT W CHRISTIE TO HIRE/PURCHASE WRENCHES WWW.WCHRISTIE.COM,
TELEPHONE 0113 2469992 EMAIL SALES@ANDREWSFASTENERS.CO.UK_ WensiTé WWW.ANDREWSFASTENERS.CO.UKINSTRUCTIONS FOR INSTALLING DIRECT TENSION
INDICTORS (DTW/CLI) FOR USE WITH PRELOAD
(HSFG) FASTENERS
LZ
Dis shouldbe assembled under he head whenever possibeasit ensures
{hat he Gol hes not been trapped by
‘movement ofthe tee! les nator
tightening. With ashort-sltted or
fvetstzed hale unde ether the bolt
head or nit aod ahardenediat washer. fy
{Fora long tetedhate, an external cover
plate ofsuticent size to completely cover
the sil shouldbe provided ata minimum
of amminick) (Figure 1).
METHOD ALTERNATE METHOD)
using hese installation procedures, for HRB 8/Part 1 bolts, the DTIS
should be compressed 10 gap of less than 0.26mm in all ofthe entry
‘paces. Figures 2a and 3a), Witha shrtslotted or oversizedhnole under
ther the bolt heador nu, adda hardenediat washer (Foralongsctted
hole, an external cove late of sucen size to completely cover te set
shouldbe provided at minimum ot mmthick) (Figures 2 2e, 30 and),
[Note:The nw Tumasure DT donot neednutfac or Blt face weshers. Te
‘extra washers were or DTla with the older design “atraight-sided
protrusions (ee depictedin Figure and), With the old design Tle extra
‘washers haveto be used between the nut anaTI to achieve consatent
bly loade. However, nul-tace and bol-tace washers are currently
required by BS 7644 but NOT by BS EN 14599 PT9 this standardhas
teplacedBs 7644)
Imptrec¢mmansnbene paes
‘Tumasure Trade merk
GRADE AND SIZE
Esch DTlis marked with a series of numbers, "W-H8 or M89" signitos
the DT stor use with BS EN 14909 Part SHR B/S 4995 Parts HEFG
bots “H1G0r 109" isforBS EN 14389 Part SHR 109 BS 4a95Pan2
HSFG bolts
LOT NUMBER
For purposes of absolute raceabilty TurnaSure OT requires each DTIto
bbe markedwitha let number. The fot number il take
thetorm al aleter followed by either one of more
rumbars Figure 4illustrates the new andimproved
Hae @ OTldesign q
CIRCUMFERENTIAL NOTCHES
The redesigned DTis have cieumierential
Ingentations spaced equally
troundtne outside orcurterence,
otrespondingt andin alignment with
teach feelr gauge entry space.