Академический Документы
Профессиональный Документы
Культура Документы
LUXCHEM
Unsaturated Polyester Resins Licensed byJapan Camposite Ca., Ltd
Technical Information
8201PT
DgSCRTPTION
Polymal 8201PT is general purpose thixotropic, pre-accelerated, non waxed type unsaturated polyester
resin of orthophthalic widely used for hand lay-up, spray and filament winding moldings. It exhibits
sxcellent resistance to heat, cheryical and water, as well as good affrnity for glass fibers. Thus providing
FRP moldings with higlr strength.
APPLICATION
Suitable for making a variety of glass flber reinforced plastic such as water and storage tanks.
SPfiCIFICATION
Typical Properties Of Liquid Polymal 820lPT :
RECOMMENDED STORAGE
Typical storage life at temperature below 25fit is 3 months. To ensure maxirnum stability
and maintain
o-Ftimum resin properties, avoid exposure to heat sources such as direct sunlight
and steam pipss. The resin
should be stored in closed container below ?soc and properly sealed to avoid moisfile pick-up and
monomer 1oss. It is skongly recommended to mix thcrcughty before use.
Disclaimer:
The information contained in this data sheet is brxed on laboratory data and field
experience .which are
believed to be accurate and reliable to the best of our knowledge. We do not guarantee
its applicability to
the user's process or assume any liability for occurrences ariiing out of its use.
our recommendations
should not be taken as inducements to infringe ary patent or viJate any law,
safety code or insurance
regulations."
CEXryFTC$TW *FENELYS$
B*lrc t &fr7t7*
8O5PT-SG
I'ESCRIPTION
rltrmat 805PT-SG is general purpose thixotropic, pre-accelerated, non-waxed
rype unsalurated polyester resin
rype widely used for hand lay-on and spray moldings. It exhibirs good
_i.f:3.pt"}talic tack free properry upoa
cuflfig.
AP?LICATION
It is used for makirrg a variety of glass fiber reinforced plastic product
especially application with multi- layers
lamination that requires long fabrication time srch as boats. silo, yachts,
etc.
SPECIFICATION
Typical Properties Ofliquid polvmal g05pT-SG :
Appearance : Pink Note
Viscosity.l) , mpa.s : 400 - 500 " Brookelield:t. VT,#3,60rpm@25t
Thixotmpic Index 2.0 - 2.5
Specific Gravity 1.1 - 1.13
Acid Value (mgKOHlg) 18*22 "2) JIS 690 r
Volatile Content(%) 37 *42 (*fetpo: 1.0%, Temp:250C )
Curing Properties*2) :
GelTime, min :10 - 15
RECOMMENDED STOR"AGE
Typical storage life at temperature belorv 250C is 3 months. To ensure maximum
stability and maiatain
o-ptiTlT resin properties, avoid exposure to keat sources such as direct sunlight
and steam pipes. The resin
should be stored in closed container belol 250C and properly sealed
to avoid moisture pick-up and
monomer 1oss. It is highly recommended io srir the resin prioi to use
.
Distlaimer Clause
trkrffrc{w oFetail*xs
P,tWcrUg, _
eBec
_fm ," R!*dt
Pink
j$ 41A
"dr!?s.Ir{flrt€r
vic6csi$ uF*.s(zfc) 4go
ftixo*opicr*ex - ef
olrtrypopldrri: (Baw*MaE t%25 t[4gzP)
Goltinne [#lr l&.5
Tin*to1rc*kedrenn lt*u ?s.0
lta
.r.dr rf,coE{**rgEs{ftd&aau* ib sfu'Etcr kagdl.td
ltudal,7.rxr#,rw *.drr5/riy
L,wl-a0r$06{?
ffi
"ffW PT. MAKMUR TANTAwIJAvA
cHEtuucAr- INDU$TRrH$
SPEC_.IEIEATTON-
PRODUCT TYPE E.GLASS
CHEMICALCOMPOSITION ALIIMINABOROSILICATE
CAS NO. 65997-t7-3
APjPIJ-C,ATIqN
FANTALOJV E GLASS WOVEN ROVI}IGS CAN BE
USED IN HAND LAY-UP, MOLD PRESS, PROCESS.
POP{JLAR PRODUCTS MADE USTNG FAh]TALON WOVEN
ROVINGS INCLUDE BOATS, PANELS.
AUTOMOBILE PARTS. STORAGE TANKS, ETC. WE STRONGLY SUGGEST LAYERING
COMBINATIONS WITH FANTATEX CHOPPED STRAI{D
MAT F'OR BEST POSSIBLE RESIJLT.
CERTIFICATE OF ANALYSIS
IEST/ANAI.r{ED EY AM
.
SPECIFICATIONS
(ClEt a,b,dESpecification D6500 10o Observer)
HOTES:
* lot number listed is the parent number of this praduct, there is nothe
The
difference of
the quality cmong that lot numbers.
xE rlrrs dacument has been produced electronically and is vqlid without a
signature