Академический Документы
Профессиональный Документы
Культура Документы
INSTRUCTION MANUAL
Part 3
296-12-18 638/002
Betriebsanleitung engl. 06.09
List of Contents Part 3
Chapt. Contents Page
p-310-ed-3-en 07-08-28
11. Survey and List of Parameters
The parameter survey is designed as an aid for finding parameters quickly. It is a summary of references
for the parameter list. Listed behind each reference are all parameters which exert an influence on the
function described by the reference.
Suppose that the inverse rotation function is to be enabled. The parameter list shows this function under
parameter number 618.
Parameters having "either/or" validity (software switches) can merely be set to value Ι or ΙΙ. In the case
of such parameters, column 4 is empty.
Parameter numbers in acute brackets; e.g. <105>, mean the value (content) set for the parameter
in question.
Example:
107 Speed for front backtack when <106> = I
I limited by <105>
II limited by <607>
Explanation:
Parameter 107 is valid only the the value (content) of parameter <106> = I.
If parameter 107 is set to I (<107> = I), then the speed for the front backtack is limited by parameter 105,
e.g. <105> = 1500. If parameter 107 is set to II (<107> = II), then the speed for the front backtack is limited
by the value of parameter 607, e.g. <607> = 4000.
Photocell LS 111/112/199
615
X5 X4 X4
SM1 / A2 1 2 M1
SM1 / A1 2 A SM
37 19
SM1 / B2 3 1 2
B 1
SM1 / B1 4
5
6
20 1 +24V 7
E11 8
OTE 0V 9
X5 [A3]
1
+5V 2
3
0V 4
5
6
7
OTE 8
E5 9
10
E6 11 S6
12
13
14
+15V 15
+24V 16
17
18
0V 19
20 500 mA
21 500 mA
A16 22 500 mA
OTE 23 500 mA
24 500 mA
25 500 mA
+24V 26
A3 27 4A Y3
A8 28 4A Y8
29 500 mA
A6 30 4A Y6
A9 31 500 mA Y9
A2 32 4A Y2
+24V 33
A5 34 8A Y5
A4 35 8A Y4
A7 36 4A Y7
A1 37 4A Y1
Y1 Stützrolle /
I max Supporting roller
4A Q
Y2 Kantenschneider /
I max edge trimmer
4A Q
Y3 Ausblasen /
blowing out
I max
4AQ
Y5 Andruckrolle /
I max pressing roller
8AQ
Y8 Saugen - Motorlauf /
I max vacuming - motor runs
4A Q
Y9 Anschlag /
I max lineal
500 mA
Q Die Summe der Lastströme aller gleichzeitig eingeschalteten Stellglieder (Magnete, Magnetventile)
darf den Wert von 4A nicht überschreiten (siehe hierzu Kapitel 2. Technische Daten).
Q The total of load currents of all servos activated simultaneously (solenoids, solenoid valves)
is not allowed to exceed 4 amps (see also section 2. Technical Specifications).
Q Le total des courants de charge de tous les vérins (aimants, électro-vannes) activés simultanément
ne doit pas dépasser 4 A (voir aussi le chapitre 2. "caractéristiques techniques").
Q A soma das correntes sob carga de todos os actuadores ligados ao mesmo tempo (ímans,
solenóides) não pode ultrapassar o valor de 4A (ver também capítulo 2. Dados Técnicos).
Q La suma de las corrientes bajo carga de todos los elementos de todos los componentes de regulación
conectados simultáneamente (imanes, válvula magnética) no podrá sobrepasar el valor de 4A (véase
también el capítulo 2. de datos técnicos).
PFAFF Industriesysteme
und Maschinen AG
Hans-Geiger-Str. 12 - IG Nord
D-67661 Kaiserslautern