Академический Документы
Профессиональный Документы
Культура Документы
This reproduction made under license agreement by Information Handling Services Inc. No
further reproduction or transmission is permitted, nor may this material be made part of a
network-accessible system, without permission of the copyright owner.
These materials have been prepared by the American Bearing Manufacturers Association.
However, the information contained in these materials has not been independently verified by
the American Bearing Manufacturers Association or Information Handling Services Inc.
Neither orgnaization warrants or assumes any liability for the accuracy or completeness of
these materials.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Rolling bearings -
--`,,```,,,,````-`-`,,`,,`,`,,`---
Thrust bearings -
Tolerances
O
B Secretariat
American Bearing Manufacturers Association
The American National Standards Institute does not develop standards and
will in no circumstances give an interpretation of any American National
Standard. Moreover, no person shall have the right or authority to issue
an interpretation of an American National Standard in the name of the
American National Standards Institute. Requests for interpretations should
be addressed to the secretariat or sponsor whose name appears on the
title page of this standard.
CAUTION NOTICE: This American National Standard may be revised or
withdrawn at any time. The procedures of the American National
Standards Institute require that action be taken periodically to reaffm,
revise, or withdraw thls standard. Purchasers of American National
Standardsmayreceivecurrentinformation on all standards by calling or ;
writing the American
National
Standards
Institute. ?
Published by
--`,,```,,,,````-`-`,,`,,`,`,,`---
Secretariat
American Bearing Man- Association
--`,,```,,,,````-`-`,,`,,`,`,,`---
This second edition.cancels and replaces the frrst edition (IS0 199:1979) which has
been technically revised.
This standard was processed and approved for submittal to ANSI by Accredited
Standards Committee B3 on Ball and Roller Bearings. Committee approval of this
standard does notnecessarilyimplythatallcommittee members voted forits
approval.
Suggestions for the improvement of this standard gained through experience with ''
its use will be welcomed. These
should be sent to: American Bearing
Manufacturers Association Secretariat,ANSI ASC B3, 1200 1% Street, N W , Suite 300,
Washington DC 20036-2422.
1 Scope
This International Standard specifies tolerances for boundary dimensions (except chamfer dimensions) and for
running accuracy of thrust rolling bearings with flat back faces specifiedIS0in104.
This International Standard does not apply to certain thrust bearings, e.g. needle roller bearings, or for particular
fields of application, e.g. special precision bearings.
in IS0 582.
Chamfer dimension limits are given
2 Normativereferences
Thefollowingstandardscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthis
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision,andparties to agreementsbasedonthisInternationalStandardareencouragedtoinvestigatethe
possibility of applying the most recent editions ofthe standards indicated below. Members ofIEC and IS0 maintain
registers of currently valid International Standards.
3 Definitions
--`,,```,,,,````-`-`,,`,,`,`,,`--- 1
Copyright American Bearing Manufacturers Association
Provided by IHS under license with ABMA
No reproduction or networking permitted without license from IHS Not for Resale
-~ ~-
~- ~ ~~~~ ~~ ~ ~ ~
~~~ ~ ~~~~ ~ ~ ~ ~ ~~ ~
D 087307300037b7 bb3 M
4 Symbols
The symbols (except those for tolerances) and the values given in the tables denote nominal dimensions unless
specified otherwise.
NOTE - Applies only to ball thrust bearings and cylindrical roller thrust bearings with 90" contact angle.
NOTE - Applies only to ball thrust bearings and cylindrical rollerthrust bearings with 90" contact angle.
5 Tolerances
2
Copyright American Bearing Manufacturers Association
Provided by IHS under license with ABMA
No reproduction or networking permitted without license from IHS Not for Resale
5.1 Normal tolerance class
See tables 1 and 2.
Table 1 - Shaft washer and bearing height
Tolerance values in micrometres
500
630
800
630
800
1 000
O
O
O 45
-100
-50
-75
75
38
55
35
40
+60
+70
+80
-600
-750
-1 O00
-- I - -
1 o00 1 250 O -125 95 50 + 100 -1 400
O 60
-1 60 120 +120 -1 600 -
-- I -
1 250 1 600
1 600 2 O00 O -200 150 75 +140 -1 900 -
2 O00 2 500 O -250 190 90 + 160 -2 300 I -
UOTE - For double-clirection bearingsthe values apply only up to and includingd2 = 190 mm.
D
mm
> Q high low max. max.
10 18 O -1 1 8
18 30 O -13 10
30 50 O -16 12
--`,,```,,,,````-`-`,,`,,`,`,,`---
50 80 O -19 14
80 120 O -22 17
120 180 O -25 19
180 250 O -30 23
250 315 O -35 26
315 400 O -40 30 Identical to Si of
shaft washerof
400 500 O -45 34 same bearing
500 630 O -50 38
630 800 O -75 55
800 lo00 O -100 75
1 O00 1 250 O -125 95
1 250 1600 O -160 120
1 600 2000 O -200 150
2wo 2500 O -250 190
2 500 2850 O -300 225
NOTE -
For double-direction bearings
the values apply
only
up to and includins
D = 360 mm.
r
Tolerance values in micrometres
--`,,```,,,,````-`-`,,`,,`,`,,`---
1 600 2 O00 o -200 150 45 +140 -1 900 - -
2 O00 2 500 O -250 190 50 +160 -2 300 - -
I NOTE - For double-direction bearingsthe values apply Only up to and includingd g = 190 mm.
>
d and d2
mm
S
r high low max. mm. high O
lW
r high
- 18 O -8 6 3 +20 -250 +150
18 30 O -10 8 3 +20 -250 +150
30 50 O -12 9 3 +20 -250 +150
50 80 O -15 11 4 +20 -300 + 150
80 120 O -20 15 4 +25 -300 +200
120 180 O -25 19 5 +25 -400 +200
180 250 O -30 23 5 +30 -400 + 250
250 315 O -35 26 7 +40 -400 -
315 400 O -40 30 7 +40 -500 -
400 500 O -45 34 9 +50 -500 -
500 630 O -50 38 li +60 -600 -
630 800 O -75 55 13 +70 -750 -
-
800
1 o00
1 250
1 O00
1 250
1 600
O
O
O
-1 O0
-1 25
-1 60
75
95
120
1 25
+80
+loo
+120
-1 O00
-1 400
-1 600
-
-
1 600 2 O00 O -200 150 30 +140 -1 900 -
2 O00 2 500 O -250 190 40 + 160 -2 300 -
--`,,```,,,,````-`-`,,`,,`,`,,`---
NOTE - For double-direction bearingsme values apply only up to and including dZ = 190 mm.
>
D
mm
z
r high low
r VDP
ma. max.
10 18 O -1 1 8
18 30 O -13 10
30 50 O -16 12
50 80 O -1 9 14
80 120 O -22 17
120 180 O -25 19
180 250 O -30 23
250 315 O -35 26
31 5 400 O -40 30 Identical to Si of
shaft washer of
400 500 O -45 34 same bearing
500 630 O -50 38
630 800 O -75 55
800 lo00 O -1 O0 75
1 O00 1 250 O -1 25 95
1 250 1600 O -1 60 120
1 600 2000 O -200 1 50
2 000 2500 O -250 190
2 500 2 850 O -300 225
NOTE- For double-direction
bearings
the
values
apply
only
up
to and includin!
D = 360 mm.
5
Copyright American Bearing Manufacturers Association
Provided by IHS under license with ABMA
No reproduction or networking permitted without license from IHS Not for Resale
5.4 Tolerance class 4
See tables 7 and 8.
Table 7 -Shaft washer and bearing 'height Tolerance values in micrometres
__
>
d and
mm
d
T high low max.
,
mm. high low high low
- 18 O -7 5 2 +20 -250 +150 -400
18 30 O -8 6 2 +20 -250 +150 -400
30 50 O -10 8 2 +20 -250 +150 -400
50 80 O -12 9 3 +20 -300 +150 -500
80 120 O 3 -15 11 +25 -300 +200 -500
120 180 O -18 14 4 +25 -400 +200 -600
180 250 O -22 17 4 +30 -400 +250 -600
250 315 O -25 19 5 +40 -400 - -
315 400 O -30 23 5 . +40 -500 - -
400 500 O -35 26 6 +50 -500 -
500 630 O -40 30 7 +60 -600 - -
630 800 O -50 40 8 +70 -750 - -
lOTE - For double-direction bearings the values apply only up to and including d2 = 190 mm.
--`,,```,,,,````-`-`,,`,,`,`,,`---
630 800 O -45 34
800 1 O00 O -60 45
UOTE- For double-direction
bearings
me
values apply only up to and including
D ==mm.
6
Copyright American Bearing Manufacturers Association
Provided by IHS under license with ABMA
No reproduction or networking permitted without license from IHS Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ICs 21.100.20
Descriptors: bearings.rollingbearings, thrust bearings, form specifications, dimensions, overall dimensions,dimensionaltolerances.
Price based on6 pages