Академический Документы
Профессиональный Документы
Культура Документы
Project 1 provides knowledge regarding the implementation and development methods of a project based on hardware or software or a combination of tools and
COURSE SYNOPSIS software. This course provides exposure to the selection and early planning of a project, techniques to develop project, application of computer aided design as
well as methods of preparing and presenting project.
COURSE CONTENT
Course Learning
Week Topic Sub-Topic Outcomes Assessment
(CLO)
1.1 Select project to undertake.
Logbook,
1.0 PROJECT SELECTION, PLANNING AND 1.2 Produce initial project proposal
1 CLO1, CLO2, CLO4 Involvement,Initial
PROPOSAL PREPARATION 1.3 Plan project Proposal, Final Proposal
1.4 Prepare final project proposal paper
2.0 APPLICATION OF COMPUTER AIDED DESIGN
2.1 Apply Computer Aided Design skills to produce circuit schematic, circuit
2-4 (CAD) IN CIRCUIT SIMULATION AND PCB LAYOUT CLO3, CLO4 Logbook, Involvement
simulation and PCB design layout for a mini hardware project.
DESIGN
3.1 Understand soldering tools and techniques.
3.2 Understand photolithography equipment and technique.
3.0 PROCEDURES TO CONSTRUCT PROJECT 3.3 Understand etching tools and techniques.
5-11 CLO3,CLO4 Logbook, Involvement
HARDWARE 3.4 Understand component testing tools and techniques.
3.5 Understand on board testing tools and techniques of project.
3.6 Apply the knowledge on hardware project construction and testing to a mini project.
4.1 Do hardware based project Logbook, Involvement,
12-16 4.0 EARLY PREPARATION OF THE PROJECT 4.2 Do software based project CLO2,CLO3,CLO4 Final Proposal,
4.3 Do hardware and software interface project Presentation
Assessment REFERENCES
TYPE OF ASSESSMENT
The course assessment is carried out in two sections:
Continuous Assessment - (CA) 100%
Final Examination -(FE) 0%
a) Attendance 1 5%
b) Involvement 1 5%
c) Initial Proposal 1 10%
d) Logbook 1 40%
e) Presentation 1 20%
f) Final Proposal 1 20%
Total 100%
SENARAI PENSYARAH KURSUS
TEORI/AMALI/ JAM
BIL KOD KURSUS
Tutorial KREDIT
PROGRAMME = DEE
1 DET1013 ELECTRICAL TECHNOLOGY 2/2/0 3
2 DET1022 ELECTRICAL WIRING 0/3/0 2
3 DEE1012 MEASUREMENT 1/2/0 2
4 DET2033 ELECTRICAL CIRCUIT 2/2/0 3
5 DEE2023 SEMICONDUCTOR DEVICES 2/2/0 3
6 DEE2034 DIGITAL ELECTRONICS 3/2/0 4
7 DEC2012 FUNDAMENTAL PROGRAMMING 1/2/0 2
8 DEE3061 COMPUTER AIDED DESIGN 0/2/0 1
9 DEE3043 ELECTRONICS CIRCUITS 2/2/0 3
10 DEE3071 ELECTRONIC COMPUTER AIDED DESIGN 0/2/0 1
11 DEP3273 COMMUNICATION SYSTEM FUNDAMENTAL 2/2/0 3
12 DEE3052 ELECTRONIC EQUIPMENT REPAIR 1/3/0 2
13 DET3053 POWER SYSTEM 2/2/0 3
14 DEC3023 COMPUTER NETWORKING FUNDAMENTAL 2/2/0 3
15 DEC5052 EMBEDDED SYSTEM APPLICATION 1/2/0 2
16 DEJ5153 PROGRAMMABLE LOGIC CONTROLLER AND AUTOMATION
2/2/0 3
17 DEE5081 PROJECT 1 0/2/0 1
18 DEE6132 CMOS VLSI LAYOUT DESIGN 1/2/0 2
19 DET3043 ELECTRICAL MACHINE 2/2/0 3
20 DET5073 POWER ELECTRONICS 2/2/0 3
21 DEC5082 INTERACTIVE MULTIMEDIA APPLICATION 1/2/0 2
KURSUS
NAMA PENSYARAH
Maziah binti Mohamad 1
Wan Ayub Bin Wan Ahmad 2
Azman bin Hussin 3