Академический Документы
Профессиональный Документы
Культура Документы
Applications
· Active SCSI terminations · Motherboard clock supplies
· Post regulator for switching power supplies · Battery chargers
· Low voltage microcontrollers
General Description
The HT1117 devices are a series of three-terminal high fixed output voltage type with a range of 1.8V to 5.0V. In-
current low voltage regulators. They can deliver an out- ternal current limit and thermal protection circuits pro-
put current of 1A and can accept input voltages up to vide protection against overload conditions that could
12V. The devices are available in both adjustable and create excessive junction temperatures.
Selection Table
Part No. Output Voltage Package Marking
HT1117-ADJ Adjust
HT1117-18 1.8V HT1117-ADJ
HT1117-18
HT1117-25 2.5V HT1117-25
SOT-223
HT1117-28 2.85V HT1117-28
HT1117-33
HT1117-33 3.3V HT1117-50
HT1117-50 5.0V
Note: For lead free devices, a ²#² mark is suffixed at the end of the date code.
Block Diagram
V IN
C u rre n t
L im itin g
A m p lifie r
T h e rm a l
P r o te c tio n V O U T
E rro r
A m p . B a n d g a p
A D J
R e fe re n c e
G N D
Pin Assignment
S O T -2 2 3
H T 1 1 1 7 -X X
1 2 3
G N D / V O U T V IN
A D J
G N D / V O U T V IN
A D J
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed
in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
²*² Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Ratings in-
dicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits.
The guaranteed specifications apply only for the test conditions listed.
Thermal Information
Symbol Parameter Package Max. Unit
Thermal Resistance
qJA SOT-223 134 °C/W
(Junction to Ambient)
PD Power Dissipation SOT-223 0.75 W
Electrical Characteristics TJ=25°C, VIN=VOUT+1.5V, IO=10mA, unless otherwise specified (see note 1)
Note: 1. Specifications are production tested at room temperature, Ta. Specifications within the -40°C to 85°C
operating temperature range are assured by design, characterization and correlation with Statistical Quality
Controls (SQC).
2. Load regulation is measured at a constant junction temperature, using pulse testing with a low ON time and
is guaranteed up to the maximum power dissipation. Power dissipation is determined by the input/output
differential voltage and the output current. Guaranteed maximum power dissipation will not be available over
the full input/output range. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - Ta) / qJA.
3. Dropout voltage is defined as the input voltage minus the output voltage that produces a 2% change in the
output voltage from the value at VIN = VOUT+1.5V with a fixed load.
4. Current limit is measured by pulsing for a short time.
Application Circuits
Basic Circuits
· Variable voltage type
V IN V IN V O U T V O U T
H T 1 1 1 7 -A D J
C 1 R 1 C 2
V R E F
1 0 m F A D J 1 2 5 W 1 0 m F
IA D J
R 2
1 k W
C o m m o n C o m m o n
S in g le p o in t G N D
R2
VOUT = VREF ( 1 + ) + IADJ R2
R1
Note: C1 is required if the needed if the device is located far from filter capacitors, the recommended value is 10mF.
C2 is required for stability, the recommended value is 10mF.
R1 is required for regulation, the recommended value is 125W.
V IN V IN H T 1 1 1 7 V O U T V O U T
S e r ie s
G N D
C 1 C 2
1 0 m F 1 0 m F
C o m m o n C o m m o n
S in g le p o in t G N D
Note: C1 is required if the needed if the device is located far from filter capacitors, the recommended value is 10mF.
C2 is required for stability, the recommended value is 10mF.
2 .7 5 £ V IN £ 1 2 V V IN V O U T V O U T
H T 1 1 1 7 -A D J
C 1 R 1 C 2
V R E F
1 0 m F A D J 1 2 5 W 1 0 m F
IA D J
R 2
1 k W
C o m m o n C o m m o n
S in g le p o in t G N D
V IN V IN V O U T V O U T
H T 1 1 1 7 -A D J
R 1
A D J 1 2 5 W
C 1 C 2
1 0 m F 1 0 m F
R 2 R 3 R 4 R 5 R n
C o m m o n C o m m o n
S in g le p o in t
In p u ts
G N D
N o te : R 2 c a n s e t th e m a x im u m v o lta g e .
T r1 IC 1
V IN V IN H T 1 1 1 7 V O U T V O U T
S e r ie s
R 1 IR E G IO
C 1 G N D C 2
1 0 m F 1 0 m F
C o m m o n C o m m o n
S in g le p o in t G N D
V B E 1
R 1 = ,
IC 1
IR E G -
(1 + b )
IO = IC 1 + IR E G
V IN V IN V O U T V O U T
H T 1 1 1 7
S e r ie s
C 1 C 2 V X X
1 0 m F G N D 1 0 m F R 1
IS S
D 1
C o m m o n S in g le p o in t G N D C o m m o n
IC 1
V IN V IN V O U T
H T 1 1 1 7
S e r ie s V O U T 1
C 3
IC 2 G N D V X X 1
1 0 m F
V IN H T 1 1 1 7 V O U T
S e r ie s
V O U T 2
C 1 G N D C 2 V
1 0 m F 1 0 m F R 1 X X 2
C o m m o n S in g le p o in t G N D C o m m o n
VOUT2 = VXX2
V IN V IN V O U T V O U T
H T 1 1 1 7
S e r ie s
C 1 C 2
1 0 m F G N D R A
1 0 m F
S in g le p o in t G N D
R B
-V IN V O
RB
-VO = VOUT x
RA
Package Information
3-pin SOT-223 Outline Dimensions
s e a tin g p la n e
g a u g e p la n e
D q
E 1 E
e A 1
A 2
e 1 A
Dimensions in mm
Symbol
Min. Nom. Max.
A ¾ ¾ 1.8
A1 0.02 ¾ 0.10
A2 1.50 ¾ 1.70
b 0.66 ¾ 0.84
C 0.23 ¾ 0.35
D 6.30 ¾ 6.70
E 6.70 ¾ 7.30
E1 3.30 ¾ 3.70
e ¾ 2.3 ¾
e1 ¾ 4.6 ¾
L 0.75 ¾ ¾
q 0° ¾ 10°
D
T 2
A B C
T 1
SOT-223
Symbol Description Dimensions in mm
A Reel Outer Diameter 330±1
B Reel Inner Diameter 62±1.5
C Spindle Hole Diameter 12.75±0.15
D Key Slit Width 2+0.6
T1 Space Between Flange 12.4+0.2
T2 Reel Thickness 16.4-0.4
P 0 P 1
D t
F
W
B 0
C
D 1 P
K 0
A 0
SOT-223
Symbol Description Dimensions in mm
W Carrier Tape Width 12±0.3
P Cavity Pitch 8±0.1
E Perforation Position 1.75±0.1
F Cavity to Perforation (Width Direction) 5.5±0.05
D Perforation Diameter 1.5+0.1
D1 Cavity Hole Diameter 1.5+0.1
P0 Perforation Pitch 4±0.1
P1 Cavity to Perforation (Length Direction) 2±0.05
A0 Cavity Length 6.9±0.1
B0 Cavity Width 7.5±0.1
K0 Cavity Depth 2.1±0.1
t Carrier Tape Thickness 0.3±0.05
C Cover Tape Width 9.3