Академический Документы
Профессиональный Документы
Культура Документы
Technical features
Medium: kv factor: Life expectancy: Materials:
Air, oxygen, neutral gases 0,15 ... 3 (Cv: 0.01 ... 0.2) ≥100 million cycles Body: PPS, PA
(10 % to 95 % humidity, non Mounting: (except Hit & Hold valves) Seat seals: NBR, FPM
condensing), 40 μm filtered Manifold Weight: Internal parts: Stainless steel,
Operation: Orifice: 30 g (0.07 lbs) PAA
Direct acting 2-way and 3-way 2/2 way valves Ambient/media temperature:
valves, normally closed and 0,5 .... 3,6 mm (0.02 ... 0.14”) -10 ... +50 °C (+14 ... +122°F)
normally opened 3/2 way valves Air supply must be dry enough
Operating pressure: 0,5 .... 1,5 mm (0.02 ... 0.06”) to avoid ice formation at
see table below page 2 Response time: temperatures below +2 °C (+35°F).
Flow: 10 ... 15 ms
6 … 120 l/min at 2 bar (29 psi) Response time measured
at +20 °C (+68°F) according to ISO 12238
Our policy is one of continued research and development. We therefore reserve the right to amend, without 01/16
notice, the specifications given in this document. (2007 - 5019e) © 2015 Fluid Automation Systems s.a. en 5.2.040.01
FAS 15 mm MICROSOL
Direct acting solenoid valve
1 1
1,2 0 ... 10 0 ... 145 0,75 24 2 NBR 1 01-221P202-H0+631A1+AYZ
11 11 2 0 ... 6 0 ... 145 1,4 24 2 NBR 1 01-221P204-H0+631A1+AYZ
1212 2 10
2 21010 12
12 22 10
10 3/2 NC 0,8 0 ... 8 0 ... 116 0,28 24 1 NBR 3 01-311P101-H0+13111+AYV
12 2 10
1,1 0 ... 10 0 ... 145 0,42 24 2 NBR 3 01-311P1011H0+63111+AYZ
1 13 11 3 1,5 0 ... 6 0 ... 87 0,55 24 2 NBR 3 01-311P1015H0+63111+AYZ
1 1
2 2 10
2 12 2 10
2
3/2 NO ECI *4) 0,8 0 ... 10 0 ... 145 0,28 24 2 NBR 3 01-321P101-H0+631A1+AYZ
12 10
2 10 12
12 10
2 10
1,1 0 ... 6 0 ... 87 0,42 24 2 NBR 3 01-321P1011H0+631A1+AYZ
1 3
1 3
1
1 3
11
3 1,5 0 ... 3 0 ... 102 0,55 24 2 NBR 3 01-321P1015H0+631A1+AYZ
2 2 10 12 2 10 3/2 UNI 0,7 0 ... 6 0 ... 87 0,24 24 2 NBR 3 01-331P1070H0+63111+AYZ
2 2 10 12 2 10
1 0 ... 3,5 0 ... 50 0,36 24 2 NBR 3 01-331P1010H0+63111+AYZ
1 3 1 3 1,5 0 ... 2 0 ... 29 0,55 24 2 NBR 3 01-331P1015H0+63111+AYZ
1 3 1 3
2 2 *1) Cv - 12
2 10
10 Value in 22[gal/min]
10 = kv x 0.07; kv for 3/2 Uni valves represents flow value between ports 2 & 3; kv for 3/2 NC & 3/2 ECI valves represents flow value between ports 1 & 2
10
*2) Valve equipped with ‚Hit & Hold‘ power saving electronic
1
1 3 *3) Valve models
3 1 available
1 3
3
with different nominal voltages
*4) ECI - Push type version
2 2 10 12 2 10
1 3
Accessories
1 3
Electrical connection
Mounting plate with M5 thread — Mounting plate with G1/8 thread — M5 ported mounting plate - Electrical connector MPM 9,4 mm
1 position for 2 ways valve up to 1 position for 2 ways 3,6 mm orifice 2 ... 8 positions industry standard (C192) to mate
2 mm orifice and 3 ways valve AMP spade 2,8 x 0,5 mm
A
M3
8,2
2 14,2
9,7
3,8 17,2
A
15,2
2
2,2
20,7 7,4
3 3,8
1 Sealing area 1
2 The recommended mounting screw tightening torque is 0,6 ± 0,1 Nm.
3 1
Value in ( ) for ECI version
Our policy is one of continued research and development. We therefore reserve the right to amend, without
en 5.2.040.02 notice, the specifications given in this document. (2007 - 5019e) © 2015 Fluid Automation Systems s.a. 01/16
FAS 15 mm MICROSOL
Direct acting solenoid valve
M3
6,9
A
2 14,2 9,7
3,8 17,2
A
4
15,2
20,7 7,4
3,3 3,3
1
3 3 ways standard
9,4
3
M3 x 3
A
M3
8,2
2 14,2
9,7
3,8 17,2
A
1
15,2
3
20,7 7,4
3 3,8 3,8
1,9
1 Sealing area
2 The recommended mounting screw tightening torque is 0,6 ± 0,1 Nm.
3 Value in ( ) for ECI version
4 ‘O’ Rings Ø 4 x 1
All solenoids are supplied with mounting screws and gasket or ‘O’ Rings.
Our policy is one of continued research and development. We therefore reserve the right to amend, without
01/16 notice, the specifications given in this document. (2007 - 5019e) © 2015 Fluid Automation Systems s.a. en 5.2.040.03
FAS 15 mm MICROSOL
Direct acting solenoid valve
8,2 2,8
G1/8
9,7
9,7
15
15
M3 M3 6
M5
12,5
15,2
9,7
8
4,5 M3
15 25
Electrical connector
Model: N050.1456
15,5 +0,1
3,5 25 9,4+- 0,1
1 23,5 3
15,5 +0,1
4,7
M3
15
24,5
35
3
Pg7 ø15
Warning
These products are intended for use in air, oxygen and neutral gas The system designer is warned to consider the failure modes of all
systems only. Do not use these products where pressures and component parts used in fluid power systems and to provide adequate
temperatures can exceed those listed under »Technical features«. safeguards to prevent personal injury or damage to equipment in the
event of such failure.
Before using these products with fluids other than those specified,
for non-industrial applications, life-support systems, or other System designers must provide a warning to end users in the system
applications not within published specifications, consult instructional manual if protection against a failure mode cannot be
IMI Precision Engineering, Fluid Automation Systems s.a. adequately provided.
Our policy is one of continued research and development. We therefore reserve the right to amend, without
en 5.2.040.04 notice, the specifications given in this document. (2007 - 5019e) © 2015 Fluid Automation Systems s.a. 01/16
Diese Produkte sind ausschließlich mit Druckluft-, Sauerstoff- und neu- Systemauslegern wird dringend empfohlen, die Störungsarten aller
trale Gassysteme zu verwenden. Sie sind dort einzusetzen, wo die unter in Pneumatiksystemen verwendeten Komponententeile zu berück-