Академический Документы
Профессиональный Документы
Культура Документы
STRUCTURAL BRACKETS
CATALOGUE
STANDARDS
Applicable Timber Standards are NZS 3603 and NZS 3604:2011.
GALVANISING
All components are hot dip galvanised to AS/NZS 4680 to 600g/m2. (Excludes Bonza Borer).
DESIGN LOADINGS
These can be derived from the characteristic strength of bolts in timber, using the relevant design code.
Recommended loadings for pole to brace cleats B128, B145 & B155 only are shown here.
SPECIAL PRODUCTS
OWMAC also manufactures custom-made products to suit specific requirements. A lead time, by discussion,
B
is required to allow for manufacture.
AVAILABILITY
The BOWMAC product range is available from leading Builders Supply Merchants throughout New Zealand.
END USE
The purchaser is responsible for checking the suitability of any component for its intended use.
30 x 10 30 x 10
216 216
198
198 200t 216
216
25
25 xx 10
10 25 x 10 30
30 xx 10
10
B132
B132 B133 B134 B134 *B135
*B135
(Nails
(Nails Included
Included Only)
Only) (Nails Included Only) (Nails Included Only)
(Nails Included Only) (Nails
(Nails &
& Bolt
Bolt Included)
Included)
92 50
75 5
92 23
5 92 75
187 50
23 92 75 92 75 5
118 23 23 98
50 5 5 23
98 98
30 x 10
72 72 150
216
5 5 250
100 100
75 75 50
4.5
100
75
100
*B138 B12 B12 B14 B16
(Bolts Included) (Nails Included Only)(Nails Included Only)(Nails Included Only) (Bolts Not Included)
*Similar also available in
stainless steel 304-2B
Refer to brochure
50
92 50
92 75 4.5 5
5
23 23
118
23 137
130
50 92 75
23 72 70
5 5
72
*B25 137 75
(Nail, Bolt & 2 Dyna
Bolts Included)
297
210
5 *B28
(Bolts & 2 Dyna
75 Bolts Included)
B195
100
80
B18 23 6
(Bolts Included) 40
50 72
23
5 180 M10 Bolt
72
138
BOLT & NAIL SIZES 130 100 x 100
6 80 Timber
40 6 80
FIXING NOTE 5
80
92
All bolt holes accommodate M12 Bolts 80
unless noted. Nail holes to accommodate
40mm x 3.15Ø F. Head square twisted. 265
shank nails. Hot dip galvanised. 210
. 296
4.5
275 250
75
23 50 345
315
Typical
250
*B45
*B38 *B75
80
250 *B35
75 6
5
23 50
5 23
23
72
72 50
275
452
315
275
345 *B79
75
72
23
*B48 *B78 *B85
4.5
*Similar also available in
5 stainless steel 304-2B
Refer to brochure
50
75
23 BOLT & NAIL SIZES
40
All bolt holes to accommodate M12 Bolts
5 unless noted. Nail holes to accommodate
200 40mm x 3.15Ø F. Head square twisted
shank nails. Hot dip galvanised.
272 23 23
6 B84
72 72
*B88 315 75
50
*Similar also available in 23
B86 stainless steel 304-2B 80 80
5 218
Refer to brochure
295
B352
ANGLE BRACKETS (No Gusset) 23
23 B353
5
5
63 B350
70 50
Holes 23
6mm Ø 63 50 3
Holes 23
124 50
B553 6mm Ø Holes 70
249 3
176 6mm Ø 72
3
B554 23
B555 142
97 B351
25 BOLTS NOT 23
72
INCLUDED
65 145
23
25 64 50
197 80
65 220
50 23
23 23 25 3
B354
5 5 75
*B50 72 50
72 72 23 72
23
23 145
80 *B51
80 98 181 140
220 23 50
72
295 181
65 50 B58 3
B54 *B55
220 80 98
72 5 98 181
23
140 181
50 25
70 50 5 *Similar also available in
23 5 25 23
B53 5 stainless steel 304-2B
5 5
70 50 5 Refer to brochure
B52
Holes
5 6mm Ø
BOLTS NOT
ANGLE BRACKETS (With Gusset) INCLUDED
5 5 B567
23 23
181 302
50
25
400 359
5 5
23
300 25
5 Holes
50
6mm Ø
98 *B163 Holes
*Similar also available 6mm Ø
181 in stainless steel 304-2B 249
B564 B565
154 Refer to brochure
B68
176
154
23
400
181
75 B165
145 197
50
ANGLES
75 50 75 50
BOLTS NOT INCLUDED
75 50
75 50
30 50
50 75 50
24
140 23 50
80 24 23
23
24 30 M16
240 140
140 24
240 Bolts
5 24 23 290 23
*B175 190 130 190
5
5
*B177
*B177
BOLT SIZES 5
5
All bolt holes to accommodate M12 Bolts
*Similar also available in
unless noted... *B176 B178
stainless steel 304-2B
Refer to brochure
Z & L BEAM SUPPORTS
*Similar also available in
100 100 50 100
stainless steel 304-2B
50
Refer to brochure 5
52 50 50
100
50
18 18 18
18 18
277 277
186 18
18 18 186
50
55
62 75
5 57
75
B98
5 5 75
75
*B108
*B109 B99 BOLTS NOT INCLUDED
135
Nail
Nail hole
hole for
for
temporary
temporary fixing
fixing Square Washers 50 x 50 x 5 B128 Bracket each side
to
to pole.
pole . 20mm Ø Stud Bolts
Not supplied Joint Characteristic 37kN
18.5kN per bracket.
75 Joint Characteristic 74kN
DUAL B128 18.5kN per bracket. SINGLE B128
80 18.5kN/Bracket
50
POLE CONSTRUCTION DETAILS
(BOLTS & WASHERS NOT INCLUDED)
FENCE STAY BRACKET BONZA
BORER
MODEL SIZE
BB150 150mm Dia.
BB200 200mm Dia.
BB250 250mm Dia.
BSB2 (ROUND)