Академический Документы
Профессиональный Документы
Культура Документы
%/-*0/%-&*
.(12%&&!)*3/"*
Description Storage
75FP system is used where The materials should be stored in clean
minimal and aesthetically pleasing and dry place. The material should be
sightline is required. It consists of protected until the final inspection by the
Aluminum frame, support slide and architect and the contractor.
elastomeric seal with appropriate anchors
and fasteners.
Features Installation
1. Suitable for most floor finishes Expansion joint system shall be installed
2. Pedestrian loads only. in accordance with manufacturer’s
3. Available in wide range to installation procedure. Prior to installation
accommodate thickness of the expansion joint site shall be inspected.
floor.
4. Seals can be installed towards the The site must be kept clean and the joints
end and are also replaceable. should be uniform before the installation.
5. Seals are available in many colors. All the anchors and fasteners should be
6. Installation is very easy. placed with the appropriate material.
Material Warranty
Aluminum confirms to ASTM B221 Kantaflex-Balco (USA) warrants the
for extrusion alloy 6063 T5/T6. material to be free of defects in material
for a period of 5 years. Materials must be
Expansion/Contraction : +/- 25% Movement installed as per the approved installation
instructions.
Finish Kantaflex-Balco shall not be liable for any
injury, loss or damage arising out of the
All exposed aluminum is mill finish. use of the product.
Description Storage
Moisture barrier system is used to prevent The materials should be stored in clean
water penetration from the expansion and dry place. The material should be
joints. The water collected in the moisture protected until the final inspection by the
barrier will evaporate from the joints. It is architect and the contractor.
applied using epoxy on top and bottom of
the edges.
Installation
Warranty
Material Kantaflex warrants the material to be free
Fibre Reinforced PVC Sheet: of defects in material for a period of five
Thickness - 0.41 mm years. Materials must be installed as per
Mass per area - 482.00 g/sq.m the approved installation instructions.
Ultimate water pressure - 90 psi Kantaflex-Balco shall not be liable for any
injury, loss or damage arising out of the
Finish use of the product.
Matt finish.
ALUMINIUM FRAME
[50mm] (MILL FINISH)
[100mm]
8X80mm
SLEEVE ANCHOR
[50mm] @ 20" (508mm) C.C.
38mm
RCC RCC
MOISTURE
BARRIER
[25mm]
75FP-1-(1X2)
[FLOOR TO FLOOR EXPANSION JOINT - PEDESTRIAN]
INSTALLATION PROCEDURE:
Ensure the joint opening is formed to a uniform width for the entire length of the joint.
Access to the bonding surface of the interface wall must be free and clear of debris. Any
obstructions must be accounted for in the installation process.
INSTALLATION INSTRUCTIONS
FOR
7500 SERIES
EXPANSION JOINT COVERS
IMPORTANT
READ THE FOLLOWING BEFORE INSTALLING
Read the following installation instructions carefully, and be sure
you understand them completely before you begin any work.
Please note that these installation instructions are for stan-
dard installations and are not intended to replace any spe-
cific details or shop drawings that differ from those depicted.
These installation instructions are for use in the instal- Blockouts are required for this installation. They can be
lation of 7500 Series Expansion Joint Cover Systems formed at the time of the initial concrete pour or at instal-
(Figure 1). lation time.
75FP
Interior Floor to Floor System
75FVP
Interior Wall to Floor System
75FVPE
Interior Wall to Floor System
75FVP-E
Interior New to Existing Floor System
NOTE Warning
A tooled edge on the corners of the concrete is CUTTING THE SEAL INTO SMALL
recommended. The radiused edge reduces the ef- LENGTHS CAN CAUSE LEAKS AND
fects of impact loading from vehicles and lessens WEAKEN THE SEAL.
the chance of edge erosion, cracking or spalling.
7500 Series Installation (except 75FVP and
7. Clean the interface walls of the concrete using a 75FVP-E)
50/50 mixture of water and Isopropyl alcohol to re-
move oil, grease, dirt, debris and other contaminants. 1. Place base members on a flat working surface
Ensure the water/alcohol is completely dried from the about the width of the face seal apart with the
cleaned surface prior to installation of the seal. channels facing each other.
NOTE
If fire barrier is provided with the system, install
it at this time. Refer to the installation instruc-
tions for the fire barrier type provided.
NOTE
If water barrier is provided with the system,
install it at this time. Refer to the installation BASE MEMBERS
instructions for the water barrier type provided.
Figure 3—Base Members and Plate
Assembly
BASE MEMBER PREP
3. Using a wood block and mallet, lightly tap the face
1. Mark the locations for the anchor holes on all of seal tabs into the channels of the base members
the base members and drill the anchor holes. (Figure 4).
NOTE
Standard anchor spacing is 20” o.c. with an
anchor hole a maximum of 3” from each end of
the base member section.
SYSTEM INSTALLATION
SEAL AND BASE MEMBER
INSTALLATION
All elastomeric seals should be installed in as long lengths Figure 4—Seal Installation Method
as possible.
4 XXXX0000 Rev. 00/00/14
INSTALLATION INSTRUCTIONS FOR 7500
SERIES EXPANSION JOINT COVERS
NOTE 4. Place the wall base member into its installed po-
Lubricating the face seal’s arrows with soapy sition. Insure the anchor holes of the member and
water or liquid soap can make installation of the substrate align with each other.
face seal easier. 5. Attach the wall base member to the substrate with
the anchors supplied by the manufacturer.
WARNING 6. Repeat steps 1 through 5 until all wall base mem-
DO NOT USE OILS OR OIL BASED LUBRI- bers have been installed for the length of the joint.
CANTS ON THE FACE SEAL ARROWS. Ensure wall base members are butted up against
each other.
CAUTION 7. Using a wood block and mallet, lightly tap the face
Ensure the face seal tab is completely engaged seal tab into the channel along the installed wall base
into the channel. members the entire length of the joint (Figure 5).
FINISH WORK
1. Place masking tape over the top of the joint cover
system to protect it during grouting of the blockout.
2. Ensure the blockout is dammed well so that grout
will not leak out onto lower levels.
3. Prepare grout in accordance with the grout manu-
facturer’s instructions.
4. Install grout continuously between the base mem-
bers and blockout (Figure 7).
Issued to:
STANDARD INFRATECH INDIA (P) LTD Order No : SIIPL/MULUGU/110/2019-2020
Project: HORTICULTURE UNIT Date : 22.04.2019
MEDAK, TELANGANA. Quantity : 163.06 Meters
This is to certify that the expansion joint of Model No: 75FP-1 Floor to Floor is tested in accordance with ASTM
E 1399 – 97 (reapproved 2009) for cyclic movement and measuring the minimum and maximum joint widths
of architectural joint systems.
Authorized signatory
DATE: 27.05.2019
Authorized signatory
Date:
S.No.
CLIENT NAME :
PROJECT :
NAME OF WORK :
LOCATION :
DATE OF START :
DATE OF COMPLETION :
QUANTITY :
Check List
Yes No
Removal of existing treatment & cleaning of surface :
ffi
Bssufft#Htrsf$rofiss
FRSBS$C
SffinftlonofrW{$n$onr
A"Shlsutiun. Assfl*Selurs*ubmission
Inr*qulred
8. filoOfipu|ton
wilhsqrnmsrrtt.
$. Hutiessfl{oelFcfen
Attention
: Mr.M.F.Sait,
Proiect
Manager
Project: MetroRailproject- phase1
Chennal
Elevated
Stations- Koyambedu, CMBT,Arumbakkam, vadapalani(including
viaduct)
andAshokNagar/KK Nagar-EAS04
Sub : CompanyProfileof KantaFlexIndiaPvt.Ltd.,for thesupplyof Elastomeric
Bearing
RefNo.: CCCL-282-C2E-1101136 Dated:30August20t1
CCCI-282-C2E-1101007Dated:09August2011
OurReference:GCC-28i1-C2E-1115269 Dated:t2Auguet2011
DearSir,
Withreference
to theConkactor
letterno.CCCL-282-C2E-1101136
dated30August
2011regarding
theabove
subject.
Weacknowledge
receipt profile
ofcompany of M/s.Kanta
Flexlndiafot. Ltd,,forthesupply
of Elastomeric
Bearing
forEAS-04 package.
Contract
TheEmployer'sRepresentative
hereby accords
Notice
of NoObjection
to theuseof M/s.Kanta
FlexIndlaM. Ltd.,
forthesupply
of Elastomeric
Bearing package
forConhact EAS-04
of ChennaiMetroRailProject,
inaccordance
with
Volume 3,Section
D,Subsection
14,
Kindly
ensure pertaining
thatthenorots to thesampling
andtesting
isadhered
to at regular
Intervals.
Yours
faithfully,
ForEgisRailg\ Mauneell
AECOM,
YEC,EgisInd$ A\ARSYL(Consortium)
&=-M
r l r
{- pierrepreumofrt
Employe/sRepresentative
Encl.: Nil.
- CMRL
CcTo : GM(EC) - forInformation
please.
Email:embve.qc@.eq$ll.conl
(or)seneral.consulta$-t0embye.com
116J-r''0'i"4'-
|
t",f t$f lr rcu lvrttu u ncttr Lrr I urriu
4
DocuMENT (DSR) $ 'i'r'"r*
suumidslor.1'nrPoRT -
$TATU$$HEET
ORIGINATSR
ffi EtrrtgYE ffi cmnl
ORIGTNAT
N" of Conlract: UAA04 DSRCodeGCC-448-C2U-1 115667-A
Refurence0f LetterlTransmittal
MTC-220-C2U-1
100510 Civil- Undergrou*&
Discipline:
Receptiondateof LetterlTransmittal
2?-47-2411 Agsessor:VBS / DFU /f;st
Discipline
Cocrdinator:
RBB
Preparedby TeamLeader:ALM T+1
ProposalofPVCWaterStopper- Kantaflex
List of documentssubmitted
N" Document reference Notificatiqn
Revision Date
A B c
Vendor Frofileof Kantaflex(lndia)Pvt. Ltd - Doc No. MTC*
I
22A-C2U-1100510
22-07-2411 X
6
T
d
g
10
11
12
13
14
15
16
Ns*ifinp,$rqn DSCIUMEhiT
RHETruAL
fdHTns'l"tlN!,,l6LLt
t{S CHf Nl'lAl
Definition
of notification: SocNo:
. , D I
q{}r
-""-:p
is required
A completeresubmission
A. Objection.
fll / n
i ? At,$tr0il It
withcomm€nts.
B. No Objection A!- j
y[,.*.c* *p1g-llPr,t"** -*
QpjQ** * f !.tb** p4irr *_ |
C. Noticeof No Ob.iection {{e*unts.**- ijrr:r."
?r&e0fticn. I
ttvlE
,'
As notedin theCommentsheetattached.
Many 0RUH«