Академический Документы
Профессиональный Документы
Культура Документы
G: Accessories
Filtration - Inlet Filter (Single Connection) G1
Filtration - Inline Filter (Dual Connection) G2
Filtration - Filter Silencers (Single Connection) G3
Filtration - Filter Element G4
Filtration - Moisture Separator G5
Measurement - Air Flow Meter G7
Measurement - Digital Flowmeter G9
Noise Reduction - Sound Attenuating Enclosure G10
Noise Reduction - Inlet/Outlet Muffler (Single Connection) G11
Noise Reduction - Inline Muffler (Dual Connection) G12
Protection - Relief Valve - Mechanical G13
Protection - Pressure Regulating Diaphram Valve G14
Protection - Gauges G15
System - Variable Frequency Drive G16
System - Air Knives G17
System - 5 Way, 3 Port, 2 Position Diverter Valve G19
System - Air Flow Switch G21
Pressure & Vacuum Arrangements G22
H: Motor Blower Options
I: Application Engineering Basics
Your own imagination and knowledge are probably the best source of in-plant and on-site applications for ROTRON regenerative blowers. This guide will help to
pinpoint and stimulate your consideration of the many alternative sources we provide to replace costly and maintenance intensive suction and pressure units
and systems. The nine major application groups are listed and a cross reference of the most common applications by industry will help you identify both
identical and similar applications in your industrial operations.
Mining
PARP Respiration
Textile
Garment Flotation Tables
Blower Textile
Garment Cutting Tables
Yarn Guiding and Tensioning
Carboard Case Erector Yarn Aspiration
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 A1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Nine Major Blower Application Areas
Manufacturing
Blower
Natural Gas Combustion Air Boost
Natural Gas Minispiral
Furnace Natural Gas Boost
Natural Gas Boost Air & Gas Sampling Oil Demisting
Gas
Combustion
Chamber
Blower
Combustion Air Boost
Blower Blower
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 A2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Nine Major Blower Application Areas
Packaging
Bag Filling
Air Knife
Aqueous Precision Cleaning Manufacturing
Hoist
Automotive Parts Drying Conveyor Belt Blow-Off
Air Knife Semiconductor Board Drying Electroplating Fume Guiding
Electroplating Parts Drying
Blower Food Processing Electroplating Solution Blow-Back
Batter Blow-Off Flat or Irregular Metal Parts Drying
Bottle & Can Drying Wire Drying
Label Drying
Salt, Spice, & Flour Blow-Off
Blower Plating Tank
Blower
General Parts Blow-Off & Drying Solution Blow-Back
Water
Water Pollution Control
UV Tube Agitation
Watewater Filter Backwash
Blower
Wastewater Treatment Tank Aeration
Bin Pad & Fluidized Bed Aeration Boat & Dock Deicing
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 A3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Product Dimensional Listing
Blowers Shipping Wt (LBS) Carton Length (In) Width (In) Height (In)
DR/EN
068 16/- 12 12 12
083 18/- 12 12 12
101 30/47 16 15 14
202 30/- 16 15 14
303 42/52 16 15 14
353 54/- 21 16 16
404 64/81 21 16 16
454 60/84 21 16 16
505 82/92 21 16 16
513 76/99 24 12 22
523 112/126 24 16 22
555 96/- 21 16 16
633 241/288 25 18 20
656 110/117 24 16 22
6 148/167 25 18 20
S7 206/- 25 18 20
757 131/158 25 18 20
808 285/287 34 23 26
833 269/297 44 29 37
858 280/338 34 23 26
S9 / P9 400/- 34 23 26
909 373/524 34 23 26
979 345/533 34 23 26
1233 400/- 34 23 26
14 620/737 43 28 33
S13 / P13 687/- 43 28 33
S15 / P15 909/- 43 28 43
Minispirals (SE2;12) 2/- 8 8 6
Nautilairs (NC33) 18/- 16 15 14
Spiral (SL2;4;5) 42/- 16 15 14
Note: Model weight will vary by HP and voltage. Refer to individual specification sheets to verify.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 B1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Industrial / Chemical Processing Blowers
AMETEK Dynamic Fluid Solutions’ ROTRON brand has long been a world leader in regenerative
blower technologies, bringing regenerative advantages to a new level, providing quiet,
maintenance-free, oil-free operation.
8.5
6.0 DIA.
216
152
99
3.9
6.71
174
0.97
25
0.29
3.71
8
94
T
OU
IN
3.02 1.00 2.3
58 1.00 O.D.
76 22
(2) PLACES
6.16 5.53
IN .35 DIA.
MM 155 9 140.5
(2) MTG. HOLES
6.41
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 162
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
DR068DJ9Y
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C1
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 068
.125 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• CE compliant - Declaration of Conformity on file
• Maximum flow: 13 SCFM
• Maximum pressure: 13.5 IWG
• Maximum vacuum: 13.5 IWG
• Standard motor: 1/8 HP, TEFC
• Cast aluminum blower housing, impeller & cover; slip-on steel flanges
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
• Various horsepowers for application-specific needs
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Cast iron (threaded) or face flanges for application-specific needs
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
• Switches - air flow, pressure, vacuum, or temperature
• External mufflers for additional silencing
• Air knives (used on blow-off applications)
• Variable frequency drive package
12 29.9 12 29.9
mbar
mbar
9 22.4 9 22.4
6 14.9 6 14.9
3 7.5 3 7.5
0 0 0 0
0 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 0 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C2
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 083
.125 HP Regenerative Blower
8.49 6.85
200.4 215.6 174
(2 PLACES)
DR083DC9Y - 036862
7.89
31.8
1.25
113.8
4.48
0.37
9.4
35.3
1.39
T
IN
OU
3.28 1.20 2.95
.397 DIA.
83.3 30.5 10.1 74.9
7.02 (2 MTG. HOLES) 6.50
IN
MM 178.3 165.1
7.36
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 186.9
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
DR083DC9Y
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested
and certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage
fluctuation. Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C3
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 083
.125 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Cast iron (threaded) or face flanges for application-specific needs
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
12 30 12 30
8 20 8 20
4 10 4 10
0 2 8 0 2 8
0 4 6 10 12 14 16 18 20 22 0 4 6 10 12 14 16 18 20 22
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C4
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 101 & CP 101
.33 HP Regenerative Blower
11.5 7.740
292 199
1.
ROTATION
DIRECTION
5.19
8.24
211
131
1.06
27
0.44
11
.41 3.12
3.7 10 79
1-11 1/2 6.5
94 2 MTG HOLES
FEMALE THREAD 165
IN BOTH PORTS 7.41
9.31
MM 188
236
NOTES
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested
and certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage
fluctuation. Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C5
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 101 & CP 101
.33 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
DR101 DR101
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0 0
0 3 6 9 12 15 18 21 24 27 30 33 0 3 6 9 12 15 18 21 24 27 30 33
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C6
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 202 & CP 202
.33 HP Regenerative Blower
11.78
9.63
299
245
STANDARD
.88 ROTATION
22
114
4.5
2.83
72
10.00
5.18
131
254
1.53
5.03
39
127
0.44
2.52 3.27 .398 DIA. (4X) 3.94
10 100
64 83
8.12 1 1/4-11 1/2 NPSC
206.2 STRAIGHT THREAD
11.30 (2X) CAST IRON FLANGES
286 8.91
226.3
IN
MM
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C7
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 202 & CP 202
.33 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
• Cast iron (threaded) or face flanges for application-specific needs
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0 0
0 5 10 15 20 25 30 35 40 45 50 55 0 5 10 15 20 25 30 35 40 45 50 55
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C8
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 303 & CP 303
0.5 HP Regenerative Blower
L 9.61
2 ROTATION DIRECTION
244.6
114.3
4.5
2.83
72
132.1
10.0
254
5.19
127
5.0
11.2
0.44
1.44
36.6
2.45 3.27 3.94
.398 DIA.
64 83.1 10.1 100.1
IN (4) MTG. HOLES
11.3 8.13
MM
287 206.5
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C9
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 303 & CP 303
0.5 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
40 100 40 100
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0
0 5 10 15 20 25 30 35 40 45 50 55 0 5 10 15 20 25 30 35 40 45 50 55
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 10
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 353 & CP 353
.75 HP Regenerative Blower
L 11.5
292
5.55
141
ROTATION DIRECTION
1
5.13
130
3.56
90
12.22
311
1.75
6.22
Ø6.13
44
158
156
0.41
OUT
10
IN
.47 DIA.
12
(4) MTG HOLES 5.12
3.15 3.75 130
79 95
IN 8.93
12.75 226.8
MM
324
10.18
NOTES 1 1/2 - 11 1/2 NPSC THREAD
BOTH PORTS 258 MODEL L (IN/MM)
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR353BR9M 13.97/355
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR353BR72M 12.5/317
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 11
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 353 & CP 353
.75 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 12
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 404 & CP 404
1.0 HP Regenerative Blower
L 11.5
1
292.1
5.04
4.12
12.18
309.4
182.4
7.18
6.28
160
0.41
8.9
42.4
1.67
3.05 3.75 5.12
.47 DIA.
79.2 95.3 11.9 130
(4) MTG. HOLES 8.93
12.63
IN 320.8 226.8
MM
10.3
1 1/2 - 11 1/2 NPSC
NOTES FEMALE THREAD 261.6
1 TERMINAL BOX CONNECTOR HOLE .88 (22.4) DIA. KNOCK-OUT BOTH PORTS MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR404AL58M 14.41/366.0
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR404AL72M 14.18/360.2
DR404AL86M 13.38/339.9
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 13
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 404 & CP 404
1.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
Legend Legend
50 Pressure: 125 50 Pressure: 125
Suction: Suction:
DR404 100 DR404 100
40 40
Inches of Water
Inches of Water
75 75
mbar
mbar
30 30
20 50 20 50
10 25 10 25
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 14
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 454 & CP 454
1.5 HP Regenerative Blower
L
4.31 12.5
1 ROTATION DIRECTION
110 318
120.7
4.75
5.24
133
4.36
111
13.5
343
4.18
106
IN OUT
175
6.9
0.42
11
2.0
51
3.25 4.75
1.78 120
83 45 .59 DIA.
15 10.30
4.5 (6) MTG HOLES
114.3 261.6
IN
MM 12.56 11.4
1 1/2 - 11 1/2 NPSC
319 FEMALE THREAD 290
NOTES BOTH PORTS
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR454R58M 14.47/367
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR454R72M 13.31/338
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 15
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 454 & CP 454
1.5 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
112 112
mbar
mbar
45 45
30 75 30 75
15 37 15 37
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 16
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 505 & CP 505
2.0 / 3.0 HP Regenerative Blower
L 13.59 DIA.
1 345.2
ROTATION DIRECTION
IA.
8D
7.1 182.4
B
366.5
14.43
.37 REF.
184.2
48.5
9.4
1.91
7.25
IN OUT
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 17
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 505 & CP 505
2.0 / 3.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
DR505AS72M DR505AS72M
Inches of Water
DR505K58M DR505K58M
mbar
mbar
45 DR505AS58M 112 45 DR505AS58M 112
30 75 30 75
15 37 15 37
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 18
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 513 & CP 513
1.5 HP Regenerative Blower
13.88 14.21
1
352.6 360
ROTATION
5.07
4.13
129
106
7.18
182
16.06
408
224
IN OUT
8.8
0.5
13
2.4
61
3.72 5.50 4.8
IN .59 DIA.
93 139.7 15 122
MM
13.69 (4) MTG HOLES 11.4
346 289.6
NOTES
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA. 1 1/2 - 11 1/2 NPSC 12.8
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. FEMALE THREAD 325
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. BOTH PORTS
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 19
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 513 & CP 513
1.5 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 20
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 523 & CP 523
3.0HP High Pressure Regenerative Blower
L SEE NOTE 1
14.21
13.63 358.1
346.2
ROTATION DIRECTION
5.23
133
4.19
4.25
108
108
16.12
409.5
6.95
220.7
8.69
IN OUT
0.5
13
56.4
2.22
4.75
120.6
4.7 5.50
.59 DIA. 11.42
119.4 139.7 15.0 1 1/2 - 11 1/2 NPSC 290.1
14.16 (4) MTG. HOLES FEMALE THREAD 12.8
BOTH PORTS
359.7 325.1
IN
MM 14.4
365.8
NOTES
1 TERMINAL BOX CONNECTOR HOLE .88 (22.4) DIA. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR523K72 15.91/404.1
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR523K58 19.31/490.5
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 21
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 523 & CP 523
3.0HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
90 225 90 225
60 150 60 150
30 75 30 75
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 22
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 555 & CP 555
3.0 / 4.0 HP Regenerative Blower
L 14.93
15.06
MODEL L (IN/MM)
NOTES
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA. DR555CK72 17.44/443
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR555K72 16.12/409
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR555K58 17.38/441
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 23
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 555 & CP 555
3.0 / 4.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR555K72 DR555K72
Inches of Water
DR555K58 DR555K58
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 24
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 6 & CP 6
3.0 / 5.0 HP Regenerative Blower
4.86 L
MUFFLER
123.4
4 4.0
.95 3.3 8
.
84 101.6
24.1
2 - 11 1/2 NPSC
FEMALE THREAD
BOTH PORTS
ROTATION DIRECTION
141.7
OU IN
5.58
T
215.9
8.50
419
16.5
16.34
415
215.9
8.50
1
102
4.0
6.98 7.0 2.00 3.20
177 178 50.8 101.6
IN
MM 14.63 8.00
.562 DIA.
(4) MTG. HOLES 203.2
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.06 (26.9) DIA. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR6D89 18.00/457.2
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
DR6K72 18.00/457.2
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 25
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 6 & CP 6
3.0 / 5.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• 52248 1 pc.
•
MOTOR OPTIONS
• International voltage & frequency (Hz)
designs
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Blower Performance at Standard Conditions
60 Hz 50 Hz
Air Flow Rate - m3/hour Air Flow Rate - m3/hour
0 34 68 102 136 170 204 238 272 306 340 374 0 34 68 102 136 170 204 238 272 306 340 374
120 300 120 300
Legend Legend
100 Pressure: 250 100 Pressure: 250
Suction: Suction:
DR6D89 DR6D89
80 200 80 200
Inches of Water
DR6K72 DR6K72
Inches of Water
DR6D5 DR6D5
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 26
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 633 & CP 633
5.0 / 7.5 HP High Pressure Regenerative Blower
4.88 13.16
124.0 334.3 16.68
1.03
26.2 423.7
DIRECTION
OF
ROTATION
18.94
481.1
10.50
266.7
10.59
269.0
3.22
81.8
IN OUT
.5.1
.20
6.22
.98 (2X) 158.0
6.10
24.9 154.9 2" NPSC
11.811 2.66 17.244
IN 438.0 FEMALE THREAD
300.0 67.6 18.41 BOTH PORTS
MM 18.06
467.6
458.7
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. INCLUDES INLET FILTER
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 27
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 633 & CP 633
5.0 / 7.5 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 275 IWG
• Maximum vacuum: 190 IWG
• Standard motor: 7.5 HP, TEFC
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR633D89M DR633D89M
Inches of Water
mbar
mbar
150 375 150 375
50 125 50 125
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 28
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 656 & CP 656
3.0 / 3.5 HP Regenerative Blower
15.42
L
390.5
STD. DIRECTION
OF ROTATION
1
Ø7.19
182.6
5.56
141
4.56
116
15.17
382.5
7.46
190
2" NPSC
STRAIGHT THDS
0.59 4.92 BOTH PORTS
17.3
0.64
57.2
2.25
4.14 5.51 15 125
(4X) MTG
105.2 140 HOLES 11.420
289.6
15.12 12.81
IN 384 325.4
MM
NOTES
MODEL L (IN/MM)
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR656CK72X 17.50/444.5
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR656K72X 16.00/406.4
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for
Class F rated motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient
temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 29
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 656 & CP 656
3.0 / 3.5 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 110 IWG
• Maximum vacuum: 89 IWG
• Standard motor: 4.0 HP, TEFC
•
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
DR656K58X DR656K58X
Inches of Water
DR656K72X DR656K72X
mbar
mbar
60 DR656CK72X 150 60 DR656CK72X 150
DR656CK5X DR656CK5X
40 100 40 100
20 50 20 50
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 30
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 757 & CP 757
4.0 / 5.0 HP Regenerative Blower
16.75
L 426
ROTATION
DIRECTION
5.04
128
17.44
443
6.57
167
2 1/2" NPSC
9.23
234
FEMALE THREADS
BOTH PORTS
5.75
2.77
70
15.3 146
21
.84
389 10.31
5.60 2.81 262
0.63 142.2 12.73
71 323.3 16.3
16 2.0
50 414
7.02
178
MODEL L (IN/MM)
2.0
50
IN
5.71
145
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 31
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 757 & CP 757
4.0 / 5.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 83 IWG
• Maximum vacuum: 75 IWG
• Standard motor: 4.0 HP, TEFC
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Legend Legend
75 Pressure: 187 75 Pressure: 187
Suction: Suction:
60 DR757D89X 149 60 DR757D89X 149
Inches of Water
Inches of Water
DR757CK72X DR757CK72X
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 30 60 90 120 150 180 210 240 270 300 330 0 30 60 90 120 150 180 210 240 270 300 330
50 50
0 0
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 32
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S7
7.5 HP High Pressure Regenerative Blower
2 - 11 1/2 NPT
FEMALE THREAD
BOTH PORTS
16.38
416.1
6.44
163.6
5.88
149.4
3.22
23.03 81.8
585 2 - 11 1/2 NPT
A FEMALE THREAD
BOTH PORTS
147.8
IN
5.58
OU
T
16.44
417.6
209.6
8.25
101.6
4.00
NOTE 1
A 4.94
IN 125.5
MM 8.03 7.00 2.00 8.00
.563 DIA.
NOTES 204 177.8 50.8 14.3 203.2
1 TERMINAL BOX CONNECTOR HOLE 1.06 (26.9) DIA. (4) MTG. HOLES 11.50
11.00
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 292.1
279.4
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. SECTION VIEW A-A
DRS7X72 DRS7X86
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 33
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S7
7.5 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
100 249 100 249
50 124 50 124
25 62 25 62
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 34
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 808 & CP 808
5.0 / 7.5 HP Regenerative Blower
L
18.73
475.7
536.4
21.12
11.75
298
1 IN OUT
91.2
3.59
3.5
22.9
0.9
8.75 7.38
187.5 .562 DIA. 88.9
222 8.5 14.3 7.0
216 (8) MTG. HOLES
22.38 177.8
568.5 1.91 14.76
48.5 374.9
15.75
IN 400.1
MM
2 1/2 - 8 NPSC 17.43
FEMALE THREAD 442.7
NOTES BOTH PORTS
MODEL L (IN/MM)
1 TERMINAL BOX CONNECTOR HOLE 1.06 (26.9) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR808AY72MX 22.23/564.6
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR808D89MX 19.31/490.5
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 35
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 808 & CP 808
5.0 / 7.5 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 120 IWG
• Maximum vacuum: 95 IWG
• Standard motor: 7.5 HP, TEFC
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR808D89MX DR808D89MX
Inches of Water
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 36
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 833 & CP 833
7.5 / 10.0 HP Regenerative Blower
5.24 13.98
.84 133.1 355.1 19.13
21.3 485.9
DIRECTION
OF
ROTATION
19.38
492.3
ROTATION
10.50 DIA
266.7
10.44
265.2
81.8
3.22
IN OUT
5.1
.20
6.22
.98 (2X) 158.0 6.10
24.9 11.811 8.71 17.638 154.9 2" - 11 1/2 NPSC
448.01 18.81 FEMALE THREAD
300.0 221.2 BOTH PORTS
24.0 477.8
609.6
(4X)
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. FILTER 515255 INCLUDED
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 37
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 833 & CP 833
7.5 / 10.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 258 IWG
• Maximum vacuum: 174 IWG
• Standard motor: 10 HP, TEFC
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR833AY72M DR833AY72M
Inches of Water
mbar
mbar
150 375 150 375
50 125 50 125
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 38
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 858 & CP 858
7.5 / 10.0 HP Regenerative Blower
L 18.60
472.4
22.34 7.09
567.4
180.3
6.81 13.53 2.00 3.55
1.19 2 1/2 - 8 NPSC
175.3 343.7 50.8 90.2 FEMALE THREAD
BOTH PORTS
4.00
101.6
ROTATION DIRECTION
11.68
296.7
OUT IN
211.1
8.31
21.81
553.9
10.18
259.1
10.13
257.3
NOTE 1
1.75
10.00 9.50 44.5 6.4 1.97
IN 256.3 241.3 162.6 50
MM
13.00 .75 X 2.00 SLOT 8.49
330.2 19.05 X 50.8 215.6
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.06 (26.9) DIA. (4) PLACES 9.99
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. MODEL L (IN/MM)
252.5 DR858AY72W 23.06/585.7
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR858BB72W 23.19/589
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 39
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 858 & CP 858
7.5 / 10.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR858BB72W DR858BB72W
Inches of Water
mbar
mbar
75 187. 75 187.
50 124 50 124
25 62 25 62
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 40
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P9
15.0 / 20.0 HP Regenerative Blower
7.09
180.1
3.55
L 90.2
4.00 DIA. SLIP-ON
2
101.6 A
ROTATION DIRECTION
207.3
8.16
21.81 REF.
18.00 DIA.
554
457.2
10.00
254
2 1/2 - 8 NPSC A
FEMALE THREAD 7.56
BOTH PORTS 10.88 9.25 192
1
276.4 234.9
10.00
12.00 .56 DIA. 254
304.8 14.2
IN (4) PLACES SECTION VIEW A-A
MM
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.37 (34.8) DIA.
2 PRESSURE OUTLET CONNECTION. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DRP9BM72C 31.75/806.5
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DRP9BL72C 33.44/849.4
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 41
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P9
15.0 / 20.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
part #515185
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DRP9BL72C DRP9BL72C
Inches of Water
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 80 160 240 320 400 480 560 640 720 800 880 0 80 160 240 320 400 480 560 640 720 800 880
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 42
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S9
15.0 / 20.0 HP High Pressure Regenerative Blower
457.2
18.0
7.09
180.1
2 1/2 - 8 NPSC
FEMALE THREAD 3.55
BOTH PORTS 90.2
L
A
ROTATION DIRECTION
207.3
8.16
21.81
554
XXXXXXX XXXXXXX XXXXXXX
254
10.0
NOTE 1
A
IN 5.00
MM 10.50 9.25 7.56 127
223 234.9 190.5
12.00 10.00
NOTES 254 MODEL L (IN/MM)
.60 X 1.35 SLOT(4) (DRS9BM72)
1 TERMINAL BOX CONNECTOR HOLE 1.37 (34.8) DIA. 304.8 .56 (14.2) DIA. (DRS9BL72) SECTION VIEW A-A DRS9BM72 31.75/806.5
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DRS9BL72 33.44/849.4
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 43
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S9
15.0 / 20.0 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
part #515185
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DRS9BM72C DRS9BM72C
Inches of Water
mbar
mbar
105 263 105 263
70 175 70 175
35 88 35 88
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 44
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 909 & CP 909
10.0 / 15.0 HP Regenerative Blower
IN
MM
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.25 (31.8) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 45
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 909 & CP 909
10.0 / 15.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards when properly piped and
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
DR909BB72W DR909BB72W
Inches of Water
mbar
mbar
90 225 90 225
60 150 60 150
30 75 30 75
0 0 0 0
0 60 120 180 240 300 360 420 480 540 600 660 0 60 120 180 240 300 360 420 480 540 600 660
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 46
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 979 & CP 979
15.0 / 20.0 HP Regenerative Blower
19.3
9.8 490.2
248.9
ROTATION
DIRECTION
OUT IN
4" NPSC
PORTS
518.2
20.4
16.88
428.8
1.
B
11.25 9.5 C
285.8 241.3 13.0 2 D
IN 330.2
MM L E
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.09 DIA. (DR979BE72W) MODEL L (IN/MM) B (IN/MM) C (IN/MM) D (IN/MM) E (IN/MM)
1.375 DIA. (DR979BH72W). DR979BH72W 29.0/736.6 12.25/311.2 11.50/292.1 13.19/335 8.09/205.5
2 .75 (19.1) X 2.00 (50.8) 4X MOUNTING SLOTS.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. DR979BE72W 25.38/644.6 10.25/260.4 8.38/212.9 9.88/250.9 6.88/174.8
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR979BE86W 25.81/655.6 10.25/260.4 8.38/212.9 9.88/250.9 6.88/174.8
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 47
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 979 & CP 979
15.0 / 20.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• CE compliant - Declaration of Conformity on file
• Maximum flow: 1100 SCFM
• Maximum pressure: 80 IWG
• Maximum vacuum: 87 IWG
• Standard motor: 15 HP, TEFC
• Cast aluminum blower housing, impeller & cover; cast iron flanges
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet & outlet internal muffling
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
• Chemical duty, high efficiency, inverter duty or industry-specific designs
• Vairous horsepowers for application-specific needs
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
• Slip-on or face flanges for application-specific needs
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
• Switches - air flow, pressure, vacuum, or temperature
• External mufflers for additional silencing
• Air knives (used on blow-off applications)
• Variable frequency drive package
DR979BH72W
Inches of Water
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 0 100 200 300 400 500 600 700 800 900 1000 1100
Temp Rise °C
Temp Rise °C
50 50
0 0
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 48
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 1233 & CP 1233
20.0 HP High Pressure Regenerative Blower
IN
MM
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1.38 (35) DIA.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD
DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 49
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 1233 & CP 1233
20.0 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Inlet Filter part# 522948
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
150 374 150 374
50 125 50 125
0 0 0 0
0 30 60 90 120 150 180 210 240 270 300 330 0 30 60 90 120 150 180 210 240 270 300 330
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 50
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P13
20.0 / 30.0 HP Regenerative Blower
ROTATION 6” - 8 NPSC FEMALE 17.78
DIRECTION 9.48 1.53/38.86 DEEP 451.71
240.79 FLEX TUBING (2X)
8.47 10.46
215.14 265.7
H
20.50
4.30
109.22 C
4.00
101.60
G
4.72
E 4” - 8 NPT (2X)
119.95
FEMALE THREAD 5.73
9.44 9.50 12.52 145.54
239.76 12.21 241.30 317.88
13.05
310.13 14.54
11.30 331.34
369.32
287.02 .75 X 2.00 SLOT
19.1 X 50.8 (4X) 35.57
903.48
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 51
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P13
20.0 / 30.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
(part# 511569)
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Inches of Water
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Motor Winding
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 52
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S13
20.0 / 30.0 HP High Pressure Regenerative Blower
3
OUT
NOTES
1 TERMINAL BOX CONNECTOR HOLE 2.50 (63.5) DIA.
2 4”-8 NPSC FEMALE THREAD, BOTH PORTS
20.49
520.4
3 LABEL INDICATES ROTATION DIRECTION AND
“IN & OUT” PORT LOCATIONS.
5 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
6 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
IN
IN 2
MM 35.57
903.5
12.33
313.2
BOTH
PORTS
215.1
8.47
25.04
636
19.79
502.7
11.28
286.5
1
109.2
4.3
1.08
27.4
4.72 10.77 4.24
107.7 SLOTS
119.9 273.6
9.44 13.63 9.50 .75x2.00
239.8 346.2 241.3 (19x50.8)
(4) PLACES
11.30 14.54
287.0 369.3
SECTION VIEW A-A
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 53
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S13
20.0 / 30.0 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
(part# 511569)
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Inches of Water
mbar
mbar
105 261 105 261
70 174 70 174
35 87 35 87
0 0 0 0
0 80 160 240 320 400 480 560 640 720 800 880 0 80 160 240 320 400 480 560 640 720 800 880
Motor Winding
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 54
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 14 & CP 14
20.0 / 25.0 / 30.0HP Regenerative Blower
29.25 17.57
743.0 446.3
7.5 9.72
190.5 247.7
SEE NOTE 1 SEE NOTE 4"-8 NPSC
1 OUT IN
FEMALE THREAD
BOTH PORTS
(CAST IRON)
ROTATION
DIRECTION
701.0
27.6
23.46
595.9
15.31 DIA
12.88
327.2
388.9
23.32 DIA
D 592.3
9.65
3.00 245.1
76.2 13.11
11.00 333
279.4 SLOTS
.75 x 2.00 11.57
IN 17.00 (19.1 x 50.8) 293.9
MM 431.8 4X PLACES
NOTES L
1 LIFTING SLOT: 1.00 X 1.70 (25.4 X 43.2)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. MODEL L (IN/MM) D (IN/MM)
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. DR14DW72MW 31.55/801.4 1.98/50.3
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 55
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR 14 & CP 14
20.0 / 25.0 / 30.0HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Inches of Water
DR14BH72MW DR14BH72MW
mbar
mbar
90 225 90 225
60 150 60 150
30 75 30 75
0 0 0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 0 100 200 300 400 500 600 700 800 900 1000 1100
Motor Winding
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 56
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P15
40.0 / 60.0 HP Regenerative Blower
24.04 REF
610.6
12.38
314.5
IA.
39.82 1D ) 9.69
2.81.4 ACES
1011.4 7 PL 246.1
A (2
2
OUT IN
290.1
11.42
OUT IN
23.30 DIA.
750.1
29.53
32.01 REF.
752.9
29.64
591.8
813.1
307.8
12.12
149.4
5.88
14.14
359.2
1
3
A
10.34
IN 14.29 11.25 3.00 262.6
MM 363 285.8 76.2
12.50
11.29 17.25 317.5
NOTES .75 X 2.00 SLOT
286.8 438.2 19 50.8
1 TERMINAL BOX CONNECTOR HOLE 2.50 (63.5) DIA. 15.62
(4) PLACES 396.7
2 4-8 NPSC FEMALE THREAD, BOTH PORTS
3 PRESSURE CONNECTION 6-8 NPSC FEMALE THREAD. SECTION VIEW A-A
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 57
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR P15
40.0 / 60.0 HP Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
•
•
(part# 516264)
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Inches of Water
mbar
mbar
75 187 75 187
50 124 50 124
25 62 25 62
0 0 0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Motor Winding
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 58
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S15
40.0 HP High Pressure Regenerative Blower
5 IN
IN
OUT
594.4
23.4
13.1
332.7
9.72
2 OUT
246.9
39.2
12.9 995.7 4
BOTH 327.7 A
PORTS
269.2
10.6
726.4
28.6
IN
MM 1
355.6
14.0
NOTES
1 TERMINAL BOX CONNECTOR HOLE .88 (22) DIA. 3
2 4-8 NPSC FEMALE THREAD, BOTH PORTS.
13.4 A
3 FOUR MOUNTING SLOTS .75 (19) X 2.00 (50.8). 12.50
152.4
6.00
4 TWO LIFTING SLOTS 1.00 (25.4) X 1.70 (43.2). 340.4 10.4 11.18 317.5
5 LABEL INDICATES ROTATION DIRECTION AND 264.2 284.0 10.8
274.3 15.6
“IN & OUT” PORT LOCATIONS. 17.25 11.6
6 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 438.2 294.6 396.2
7 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. SECTION VIEW A-A
DRS15BQ72 DRS15BQ86
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 59
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Industrial / Chemical Processing Blowers
DR S15
40.0 HP High Pressure Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings
• Quiet operation within OSHA standards when properly piped or muffled -
1 inlet muffler included (part# 516264)
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
Legend
200 Pressure: 500
Suction:
160 DRS15 400
Inches of Water
mbar
120 300
80 200
40 100
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100
50
0
Temperature curves are based on standard model
100
Temp Rise °C
Blower Air
50
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS C 60
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Environmental / Chemical Processing Blowers
Our environmental EN blowers are designed the same as the DR blowers, except added features
include:
vacuum impregnated
Teflon® lip seal in a stainless steel case standard for leakage containment to 25 cc/min or less
Explosion-proof motors standard and available in a variety of world voltages
All metal-to-metal surfaces are sealed with RTV sealant
Various UL explosion-proof listings. Consult factory.
Environmental (EN) regenerative blowers are also available in our Chemical Processing (CP)
configuration:
4.13
104.9
ROTATION
DIRECTION
1
6.13
155.7
7.74
14.01
355.9
195.6
12.51
317.8
244.6
9.63
140.5
5.53
1.00
25.4
0.40
10.2
IN OUT
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 101 & CP 101
.5 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
15 37.3 15 37.3
10 24.9 10 24.9
5 12.5 5 12.5
0 0 0 0
0 3 6 9 12 15 18 21 24 27 30 33 0 3 6 9 12 15 18 21 24 27 30 33
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.comcom ____
Environmental / Chemical Processing Blowers
EN 303 & CP 303
.5 HP Sealed Regenerative w/Explosion-Proof motor
1
12.04 9.61
305.8 244.1
177.3
6.98
146.1
5.75
274.8
10.82
147.1
5.79
34.8
1.37
0.48
12.2
T
OU
IN
3.38 3.27 1.97
.397 DIA.
85.9 83.1 10 50
(4) MTG HOLES 3.94
IN 10.90
MM 100.1
276.9 4.06
NOTES 103.1
1 1/4" - 11 1/2 NPSC
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD> FEMALE THREAD 8.91
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. BOTH PORTS
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 226.3
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 303 & CP 303
.5 HP Sealed Regenerative w/Explosion-Proof motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0
0 5 10 15 20 25 30 35 40 45 50 55 0 5 10 15 20 25 30 35 40 45 50 55
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D4
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 404 & CP 404
1.0 HP Sealed Regenerative w/Explosion-Proof Motor
6.66
169.2
4.92
ROTATION DIRECTION
L 125
11
29 .5 D
2.1 IA
12.23
182.4
311.2
7.18
159.5
6.28
0.44
11.2
3.04 3.75 5.12
.47 DIA.
76.2 95.3 11.9 130
IN (4) MTG. HOLES
11.63 8.93
MM 1 1/2 - 11 1/2 NPSC
295.4 FEMALE THREAD 226.8
BOTH PORTS
NOTES 10.13
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT. 257.3
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. MODEL L (IN/MM)
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. EN404AR58ML 16.41/416.8
EN404AR72ML 15.50/393.7
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 404 & CP 404
1.0 HP Sealed Regenerative w/Explosion-Proof Motor *ATEX model certified
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 454 & CP 454
1.5 HP Sealed Regenerative w/Explosion-Proof Motor
18.70 12.5
ROTATION DIRECTION
475.0 317.5
120.7
4.75
13.53
343.7
177.3
IN OUT
6.98
48.8
1.92
10.7
0.42
3.27 1.78
83.1 45.2 .59 DIA. 1
4.50 15
114.3 (6) MTG. HOLES
4.75
120.6
13.10
332.7
1 1/2 - 11 1/2 NPSC 5.38
FEMALE THREAD 136.7
IN BOTH PORTS
10.30
MM
261.6
NOTES
11.4 REF.
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 289.6
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D7
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 454 & CP 454
1.5 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
60 149 60 149
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D8
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 505 & CP 505
2.0 / 2.5 HP Sealed Regenerative w/Explosion-Proof Motor
IN
MM
NOTES
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D9
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 505 & CP 505
2.0 / 2.5 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
EN505AX58ML EN505AX58ML
Inches of Water
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 10
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 513 & CP 513
1.5 HP Sealed Regenerative w/Explosion-Proof Motor
15.70 14.21
398.8 360.9 ROTATION DIRECTION
4.42
112.3 6.69
170
181.9
15.92
404.4
223.5
IN OUT
8.8
2.24
56.9
12.7
0.5
3.72 5.50 4.75
.59 DIA. 120.6
94.5 139.7 15
(4) MTG. HOLES
13.64
5.53
346.5 140
IN 1 1/2 - 11 1/2 NPSC 12.8
13.87
MM FEMALE THREAD
352.3 325.1
BOTH PORTS
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 11
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 513 & CP 513
1.5 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 12
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 523 & CP 523
3.0 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
19.19 14.21
487.4 360.9 SEE NOTE
6.56
1 ROTATION DIRECTION
166.6
146.1
5.75
7.16
408.7
16.01
14.38
365.3
IN OUT
223.8
8.69
2.22
60.5
0.50
12.7
4.75
5.56 5.50
.59 DIA. 120.6
141.2 139.7 15
(4) MTG. HOLES 5.71
15.68
145
398.3
IN 11.42
MM 290.1
1 1/2 - 11 1/2 NPSC
FEMALE THREAD 12.8
NOTES BOTH PORTS
325.1
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 13
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 523 & CP 523
3.0 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
90 225 90 225
60 150 60 150
30 75 30 75
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 14
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 6 & CP 6
5.0 HP Sealed Regenerative w/Explosion-Proof Motor
16.38
416.1
L 7.75
196.9 2 - 11 1/2 NPSC
6.37 FEMALE THREAD
4.19 BOTH PORTS
161.8
106.4 0.95
24.6
OU
141.7
IN
5.58
T
16.222
423.9
16.69
215.9
8.50
209.6
8.25
101.6
4.00
7.18 7.00 5.98
2.00
IN 182.4 177.8 50.8 NOTE 1 151.9
MM 8.00
16.18
.562 DIA. 203.2
411.0 14.3
NOTES (4) MTG. HOLES 11.50
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD
292.1
POSITIONED AT 12 O’CLOCK. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. EN6F72L 20.5/520.7
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
EN6F5L 20.84/529.2
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 15
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 6 & CP 6
5.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
• Muffler included (part# 522948)
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
EN6F5L EN6F5L
Inches of Water
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 16
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN / CP 633
7.5 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
1.03 A
C
26.2
DIRECTION
OF
ROTATION
ROTATION
11.71
297.4
10.59
269.0
3.22
81.8
IN OUT
5.1
.20
6.22
.98 (2X) 158.0 6.10
24.9 2.66 154.9 2" - 11 1/2 NPSC
11.811 D FEMALE THREAD
300.0 67.6 18.41 BOTH PORTS
18.06 467.6
458.7
IN
MM .512
MTG. HOLE
13.0 DETAIL
15.0
.591
(4X)
NOTES MODEL A B C D
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD. EN633 18.1 18.94 16.7 17.3
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. EN833 18.2 19.59 18.0 17.6
Part/Model Number
EN633BA72LM CP633FY72LR
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 17
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN / CP 633
7.5 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 200/195 IWG
• Maximum vacuum: 155/155 IWG
• Standard motor: 7.5 HP, explosion-proof
• Cast aluminum blower housing, impeller , cover & manifold; cast iron
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
625
250
500
Inches of Water
200
mbar
375
150
250
100
125
50
0
20 40 60 80 100 120 140 160 180 200 220
50
0
Temperature curves are based on standard model
100
Temp Rise °C
Blower Air
50
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
0
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
0
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 18
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 656 & CP 656
3.0 HP Sealed Regenerative w/Explosion-Proof Motor
19.37 15.42
STD. DIRECTION
492.0 OF ROTATION 391.7 7.19
182.6
176.8
6.96
136.7
5.38
15.17
1
382.5
189.5
7.46
2" NPSC
STRAIGHT THDS
BOTH PORTS
2.31
4.92
58.7
0.59
0.64
17.3
4.14 5.51 15 125
105.2 140 (4X) MTG 11.420
IN HOLES
290.1
MM
15.12 12.81
382.5 325.4
NOTES
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 19
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 656 & CP 656
3.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 75 IWG
• Maximum vacuum: 73 IWG
• Standard motor: 3.0 HP, explosion-proof
• Cast aluminum blower housing, impeller , cover & manifold; cast iron
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
EN656M5XL EN656M5XL
Inches of Water
mbar
mbar
45 112 45 112
30 75 30 75
15 37 15 37
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 20
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 757 Single-Phase and CP Options
Sealed Regenerative Blower w/Explosion-proof Motor
23.35
10.33
593.1
15.36 262.4
5.73
2.61
66.3
390.1
145.5
ROTATION
OUT IN DIRECTION
233.2
9.18
1
166.9
2 1/2" NPSC
6.57
427.2
16.82
493.5
19.43
FEMALE THREADS
BOTH PORTS
258.6
10.18
437.9
17.24
9.50 8.50
1.75
44.5 241.3 215.9
IN .75 X 2.00 SLOT 10.00
MM 6.04 13.00 19/50.8 254
153.4 330.2 (4) PLACES 16.64
422.7
NOTES
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
EN757FL5MWL CP757FX5MWLR
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 21
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 757 Single-Phase and CP Options
Sealed Regenerative Blower w/Explosion-proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
60 150
40 100
20 50
0 0
0 40 80 120 160 200 240 260 300 340 380 420
120
Air Flow Rate - SCFM
100
Motor Winding
Temp Rise °C
50
0
Temperature curves are based on standard model
100
Temp Rise °C
Blower Air
50
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 22
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 757 & CP 757
3.0 / 5.0 HP Sealed Regenerative w/Explosion-Proof Motor
16.75
L 425.5
ROTATION
DIRECTION
IN
NAMEPLATE
7.18
MOTOR MODEL:
17.44
182
PART NO.
443
166.9
6.57
2 1/2" NPSC
234.4
FEMALE THREADS
9.23
BOTH PORTS
IN 5.73 OUT
2.61
66.3
146.1
0.88
15.36 10.37
388.6 263.4
5.60 2.84 15.35
0.63 142.2
16 1.99 16.09 389.9
50.5 408.7
181.6
7.15
50.8
2.0
IN
5.59
142
MM R0.31
7.9
CL OF BLOWER
NOTES
1 TERMINAL BOX CONNECTOR HOLE .75 NPT. MODEL L (IN/MM)
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. EN757M72XL 19.72/500.9
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. EN757F72XL 21.00/533.4
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 23
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 757 & CP 757
3.0 / 5.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
EN757M72XL EN757M72XL
Inches of Water
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 30 60 90 120 150 180 210 240 270 300 330 0 30 60 90 120 150 180 210 240 270 300 330
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 24
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 808 Single-Phase and CP Options
Sealed Regenerative Blower w/Explosion-proof Motor
23.35
10.33
593.1
15.36 262.4
5.73
2.61
66.3
390.1
145.5
ROTATION
OUT IN DIRECTION
233.2
9.18
1
166.9
2 1/2" NPSC
6.57
427.2
16.82
493.5
19.43
FEMALE THREADS
BOTH PORTS
258.6
10.18
437.9
17.24
9.50 8.50
1.75
44.5 241.3 215.9
IN .75 X 2.00 SLOT 10.00
MM 6.04 13.00 19/50.8 254
153.4 330.2 (4) PLACES 16.64
422.7
NOTES
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 25
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 808 Single-Phase and CP Options
Sealed Regenerative Blower w/Explosion-proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
60 150
40 100
20 50
0 0
0 40 80 120 160 200 240 260 300 340 380 420
50
0
Temperature curves are based on standard model
100
Temp Rise °C
Blower Air
50
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 26
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 808 & CP 808 Three-Phase
Sealed Regenerative Blower w/Explosion-proof Motor
23.56
598.4 18.5
470
ROTATION
DIRECTION
282.7
11.13
480.3
18.91
21.12
NOTE 1
537
6.75
171.5
298.7
11.74
IN OUT
22.4
0.88
3.58
90.9
8.75 7.38 3.55
.562 DIA.
222.3 187.5 14.3 90.2
(8) MTG. HOLES 7.09
8.60 8.50
217.4 215.9 1.25 180.1
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 27
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 808 & CP 808 Three-Phase
Sealed Regenerative Blower w/Explosion-proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 28
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN / CP 833
7.5 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
1.03 A
C
26.2
DIRECTION
OF
ROTATION
ROTATION
11.71
297.4
10.59
269.0
3.22
81.8
IN OUT
5.1
.20
6.22
.98 (2X) 158.0 6.10
24.9 2.66 154.9 2" - 11 1/2 NPSC
11.811 D FEMALE THREAD
300.0 67.6 18.41 BOTH PORTS
18.06 467.6
458.7
IN
MM .512
MTG. HOLE
13.0 DETAIL
15.0
.591
(4X)
NOTES MODEL A B C D
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT FEMALE THREAD. EN633 18.1 18.94 16.7 17.3
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. EN833 18.2 19.59 18.0 17.6
Part/Model Number
EN833BA72LM CP833FY72LRM
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 29
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN / CP 833
7.5 HP High Pressure Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 200/195 IWG
• Maximum vacuum: 155/155 IWG
• Standard motor: 7.5 HP, explosion-proof
• Cast aluminum blower housing, impeller , cover & manifold; cast iron
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
250 625
200 500
150
mbar
Inches of
375
Water
100 250
50 125
0 0
0 20 40 60 80 100 120 140 160 180 200 220
50
0
Temperature curves are based on standard model
100
Temp Rise °C
Blower Air
50
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 30
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 858 & CP 858
7.5 / 10.0 HP Sealed Regenerative w/Explosion-Proof Motor
18.60
L 472.4 2 1/2" NPSC
23.34 15.48 FEMALE THREAD
393.2 BOTH PORTS
592.8
6.92 13.53 7.09
1.91 180.1
175.8 343.7
48.5
ROTATION DIRECTION
OUT IN
8.17
207.5
622.3
24.5
21.81
554.0
481.3
18.95
10.50
266.7
NOTE 1
6.75
13.00 171.4
IN
MM 330.2 1.75 8.21
10.75 9.50 44.5 208.5
273.1 241.3 9.46
NOTES
240.3 MODEL L (IN/MM)
1 TERMINAL BOX CONNECTOR HOLE 3/4” NPT.
10.96 EN858BA72WL 23.65/600.7
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 278.4 EN858BD72WL 26.00/660.4
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 31
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 858 & CP 858
7.5 / 10.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 120 IWG
• Maximum vacuum: 95 IWG
• Standard motor: 10 HP, explosion-proof
• Cast aluminum blower housing, impeller , cover & manifold; cast iron
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
EN858BA72WL
Inches of Water
EN858BA72WL
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 32
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 909 & CP 909
10.0 / 15.0 HP Sealed Regenerative w/Explosion-Proof Motor
L
24.73
628.1
7.23 15.99 8.34
1.37
185.7 403.1 34.8 211.8
4 - 8 NPSC
FEMALE THREAD
BOTH PORTS
IN OUT
ROTATION DIRECTION
231.9
9.13
657.9
25.9
20.25
514.4
EN909BG72WL - 038629
266.7
10.5
3.88
111
8.46
11.6 9.50 3.00 SEE NOTE
IN 1 214.9
352.0 241.3 64.3
MM 8.5
9.06 15.50 .75 X 2.00 SLOT 215.9
275.8 369.8 (4) PLACES
10.75
NOTES MODEL L(IN/MM)
1 TERMINAL BOX CONNECTOR HOLE 1 1/4” NPT FEMALE THREAD. 273.1
EN909BG72WL 30.17/766.3
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. EN909DB72WL 23.66/601.0
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
D 33
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 909 & CP 909
10.0 / 15.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
EN909BD72WL EN909BD72WL
Inches of Water
mbar
mbar
75 187 75 187
50 124 50 124
25 62 25 62
0 0 0 0
0 60 120 180 240 300 360 420 480 540 600 660 0 60 120 180 240 300 360 420 480 540 600 660
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 34
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 979 & CP 979
20.0 HP Sealed Regenerative w/Explosion-Proof Motor
19.25
1.50 DIA. (38.1) 489.0 9.75
LIFTING LUG 247.7
OUT IN
4" NPSC
PORTS
ROTATION
DIRECTION
25.32
643.1
21.77
553.0
311.2
12.25
1.
10.37
263.4 5.69
2.47
62.7
0.76
19.3
48.5 50.8
289.1
8.75
222.3 11.11
IN 282.2
9.00
MM
228.6 13.06
31.25
NOTES 793.8 331.7
1 TERMINAL BOX CONNECTOR HOLE 1 1/4” NPT FEMALE THREAD.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 35
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 979 & CP 979
20.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
mbar
mbar
60 150 60 150
40 100 40 100
20 50 20 50
0 0 0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 0 100 200 300 400 500 600 700 800 900 1000 1100
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 36
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 14 & CP 14
20.0 / 30.0 HP Sealed Regenerative w/Explosion-Proof Motor
17.57
30.14 446.19
765.56 9.64
8.61 244.86
218.69 4-8 NPSC
OUT IN
FEMALE THREAD
BOTH PORTS
(CAST IRON)
ROTATION
DIRECTION
786.38
617.22
30.96
24.3
327.15
12.88
15.32
29.74
389.13
1.17
23.32
592.39
3.00 9.65
76.12 245.03
11.00 14.32
IN 10.25 279.40 363.73
16.99
MM 260.32 431.64 SLOTS
.75 x 2.00 12.76
L (19.1 x 50.8) 324.10 MODEL LENGTH (IN/MM)
NOTES
1 TERMINAL BOX CONNECTOR HOLE 1 1/4” NPT FEMALE THREAD. 4X PLACES EN14BK72MWL 32.12/815.9
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. EN14DX72MWL 31.185/792.1
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and
certified to operate on both: 208-230/415-460 VAC-3 ph-60 Hz and 190-208/380-415 VAC-3 ph-50 Hz. Our dual voltage 1 phase motors are factory tested and
certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage fluctuation.
Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 37
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Environmental / Chemical Processing Blowers
EN 14 & CP 14
20.0 / 30.0 HP Sealed Regenerative w/Explosion-Proof Motor
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
•
• Maximum pressure: 144 IWG
• Maximum vacuum: 115 IWG
• Standard motor: 30 HP, explosion-proof
• Cast aluminum blower housing, impeller , cover & manifold; cast iron
• UL & CSA approved motor with permanently sealed ball bearings for
explosive gas atmospheres Class I Group D minimum
• Sealed blower assembly
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
• Variable frequency drive package
Inches of Water
mbar
mbar
90 225 90 225
60 150 60 150
30 75 30 75
0 0 0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 0 100 200 300 400 500 600 700 800 900 1000 1100
Motor Winding
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 D 38
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motor-less) Blowers
AMETEK Technical & Industrial Products’ ROTRON brand has long been a world leader in regen-
erative blower technologies, bringing regenerative advantages to a new level, providing quiet,
maintenance-free, oil-free operation.
Our industrial (_RD) Remote Drive Blowers are motorless models built with DR/EN/CP/SL blower
features and include:
A ROTATION
AIR IN E
AIR OUT
D G
NOTES
1 CONTACT FACTORY FOR PULLEY OPTIONS.
2 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Specification IN/MM
50 125 50 125
14,000 RPM 14,000 RPM
Inches of Water
Inches of Water
40 100 40 100
12,000 RPM 12,000 RPM
mbar
mbar
30 75 30 75
10,000 RPM 10,000 RPM
20 50 20 50
10 25 10 25
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
.4 .4
10,000 RPM 10,000 RPM
0 0
Do not exceed maximum speed shown on each graph. Do not exceed maximum speed shown on each graph.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
SL2RD
B
Q
K 4 MTG HOLES
J E L
G
ROTATION
N IN OUT
P
S FLAT
D
4 MTG HOLES H 1/4-20 UNC - 2B X 44
(SAME AS OPPOSITE SIDE) 4 HOLES EQ SPACED ON 4.43 DIA
A
NOTES R
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Specification IN/MM
25˚C
00
Inches of Water
Inches of Water
80 200 80 100
C
T1
0˚
RA
˚C
10
˚C
75
50
AT
AI
mbar
mbar
60 ˚C 60 150 60 75
25
R
00 600
AI
55 RP 550 0R
50 00 M 0R PM
450 00 RP 500 PM
40
40 R M 100 40 450 0R 50
0R
3500
RPM 00 RPM PM PM 400
0
0R
PM
PM
3000 35 R P
20 2500
RPM
50 20 3000 00 RPM M 25
RPM 2500 R RPM
PM
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
1.5 1.5
Input
Input
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 404RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
80 200 80 200
50˚C 55
55
65
00
mbar
mbar
00
RP
65
25˚C
RP
M
RP
00
M
RP
M
40 100 40 45 100
00
M
45
35 RP
250 00
00
25
35
175 M
20 00 50 20 175 0R RP 50
00
0R
RP
RP 0R P
PM PM M M
RP
M
M
M
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
4.0 4.0
2.0 2.0
Input
Input
0.8 0.8
6500
0.4 0.4 6500
3500 4500 5500 4500 5500
0.1 2500 0.1 2500 3500
1750 1750
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 505RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
75˚C
65
00
mbar
mbar
00
90 224 90 224
RP
RP
M
50˚C
M
30 175 00 RP 75 30 1750 0R 35 M 75
00
RP RPM PM 00 45
0R M 00
RP 25˚C
RP
PM M RP
25˚C M M
M
0 0 0 0
0 25 50 75 100 125 150 175 200 225 250 275 0 25 50 75 100 125 150 175 200 225 250 275
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E4
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 513RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
90 224 90 224
25˚C
25˚C
60 150 60 150
60
45
600
35
45
35
550
00
00
55
00
00
00
25
0R
25
0R
30 75 30 00 R 75
00
RP
RP
RP
RP
PM
00
RP
RP
PM
M
PM
M
M
R
M
M
PM
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Input
Input
4 4
6000 6000
5500
5500 4500
0 4500 0 3500
2500 3500 2500
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 523RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
120 298 120 298
250
0R 35
60
PM 00 45
55
00
80 199 80 RP 00 199
00
25˚C 250 M RP
RP
0R M
RP
PM
M
60
55
45
M
35
175
RP
RP
R
0R 1750
RP
PM
PM RPM
M
M
M
0 0 0 0
0 15 30 45 60 75 90 105 120 135 150 165 0 15 30 45 60 75 90 105 120 135 150 165
Input
Input
8 8 6000
6000
5500
0 5500 4500
2500 3500 4500 0 2500 3500
1750 1750
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 6RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
AIR AT 100˚C
Inches of Water
mbar
90 224 90 224
45
00 50˚C
55
R
00
60 PM 150 60 35 45 55 150
RP
00 00 00
250 RP RP RP
M
25 35 0R M M M
30 75 30 PM 75
175 00R 00 25˚C 25˚C
0R PM RP
PM M 1750
0 0 0 RPM 0
0 30 60 90 120 150 180 210 240 270 300 330 0 30 60 90 120 150 180 210 240 270 300 330
Input
Input
10 10
5500 5500
3500 4500 3500 4500
0 0
1750 2500 1750 2500
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E7
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 656RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
90 224 90 224
25˚C
60
PM
55
55
45
35
RP
45
35 00
00
25
0R
00
00
0 00
00
RP
M
30 0 75 30 75
R
RP
RP
M
PM
RP
PM
PM
17
RP
M
50 M
M
1750
M
RPM RPM
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Input
Input
15 15
6000 6000
4500 5500 4500 5500
0 2500 3500 0 2500 3500
1750 1750
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
E8
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 757RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
90 224 90 224
55
00
25 50˚C 45
45
35
00 25 35 00 00
RP
00
00
30 RP 75 30 00 00 RP RP 75
RP RP
M
R
RP
M M M
PM
M M
M
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Input
Input
20 20
5500
4500 5500
0 3500 4500 0
2500 2500 3500
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258
Customer Service Fax: +1 215.256.1338
E9
www.ametekdfs.com
Remote Drive (Motorless) Blowers
DR/EN/CP 858RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
40
90 224 90 224
00
50˚C
RP
35
25˚C 150 00 40
M
60 60 RP 0 150
M 0R
35 PM
25 00 250
30 175 00 75 30 0 RP 75
0R RP R 1750 M
PM M PM RPM 25˚C
0 0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 0 40 80 120 160 200 240 280 320 360 400 440
Input
Input
10 10
4000
4000
0 0
1750 2500 3500 1750 2500 3500
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E 10
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 909RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
75˚C
Inches of Water
Inches of Water
mbar
90 224 90 224
50˚C
50˚C
60 150 60 150
45
35 00
45
35
25 00 RP
00
00
30 00 75 30 250 RP M 75
175 1750 M
RP
RP 0R
RP
0R RPM PM
PM M
M
0 0 0 0
0 80 160 240 320 400 480 560 640 720 800 880 0 80 160 240 320 400 480 560 640 720 800 880
Input
Input
20 20
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E 11
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 979RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
90 224 90 224
50˚C
60 150 60 150
35 37 37
1750 R 250 00 00 00
30 PM RP 75 30 250 350 RP 75
0 RP RP 1750 R 0 RP 0R M
M M M PM M PM
0 0 0 0
0 120 240 360 480 600 720 840 960 1080 1200 1320 0 120 240 360 480 600 720 840 960 1080 1200 1320
Input
Input
20 20
3700 3700
3500
0 0 2500 3500
1750 2500 1750
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E 12
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Remote Drive (Motorless) Blowers
DR/EN/CP 1233RD
N +/- .25
ROTATION
2.36
59.9
M +/- .25
B
(2X) T (4X) R
Specification
mbar
150 298 120 298
75˚C
50˚C
100 50˚C 199 80 199
28
40
45
35
50
43
40 00
00
00
00
00
35 RP
RP
50 100 40 28 00 RP 100
R
50 M
RP
RP
M
RP
PM
RP M
M
M M
M
0 0 0 0
80 120 160 200 240 280 320 360 400 440 480 520 0 40 80 120 160 200 240 280 320 360 400 440
Input
Input
15 15
4300 4500
4000 4000
5 3500 5 3500
2850 2850
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS E 13
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Remote Drive (Motorless) Blowers
DR/EN/CP 14RD
B B
A A M NPSC L
N ROTATION
OUT IN
E KEY D E KEY P
D
F F
C C
G G Q
Specification IN/MM
mbar
90 224 90 224
37
60 150 60 37 150
00
00
35
35
RP
25
RP
250 00
00
17 M
00
50 175 0R RP
M
30 75 30 0R 75
RP
PM M
R
RP PM
PM
M
M
0 0 0 0
0 80 160 240 320 400 480 560 640 720 800 880 0 80 160 240 320 400 480 560 640 720 800 880
Input
Input
30 30
3700 3700
3500 2500 3500
0 2500 0 1750
1750
Do not exceed maximum speed shown on each graph or 100°C. Do not exceed maximum speed shown on each graph or 100°C.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 E 14
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Regenerative Blowers
Specialty blowers for Commercial Spa, High Temperature, Natural Gas, and Gasoline Vapor
Recovery applications.
Our instrument grade and variable flow SE (MinispiralTM Regenerative) blowers include:
AC and DC versions available for world voltages and maximum flow variability
Glass filled molded phenolic impeller; aluminum and phenolic case
30,000 hour bearing life
Small size and lightweight construction
Quiet to NC-47 office equipment standards
.25 REF.
56.9
14.22
19.05
6.35
.56
OUT
4.16 REF.
105.66
39.12
1.54
2
53.34
2.10
IN
.67
.09 TYP.
11.18
0.32 .53
17.02
2.29
8.13 13.46
1.75 2.03
1.13 .68 MAX. 44.45 51.56
IN 28.7 17.27
MM 3.50
1.80 REF. 88.9 .212 DIA.
45.72 5.38
NOTES 4.06 (2) MTG. HOLES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 103.12
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
1 Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated motors
or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or
ambient temperatures above 40°C.
2 Maximum blower amps corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or
ambient temperature reaches the maximum operating temperature.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral
Insrument Grade Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
OPTIONS
• Sealed units
• International voltage and frequency (Hz)
50 60
NC
3 FEET (0.91 METERS) FROM NOISE SOURCE
50
EQUIVALENT SOUND PRESSURE LEVEL –
db (re 0.0002 microbar)
40 50
40
30 40
30
20 30
63 125 250 500 1000 2000 4000 8000
OCTAVE BAND CENTERFREQUENCY Hz
Legend Legend
Pressure: Pressure:
Suction: Suction:
3.0 Minispiral 7.5 3.0 Minispiral 7.5
Inches of Water
Inches of Water
mbar
mbar
0 0 0 0
0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral MDC
Variable Flow Regenerative Blower
4.11 DIA.
104.4
2 leads. 20 ga. 1.65
TFE covered. 41.91
UL style 1180
(12" long, stripped 50")
DIA.
.75 O.D. TYP.
Ø2.24
.25 REF.
56.9
14.22
19.05
6.35
OUT
.56
4.16 REF.
105.66
39.12
1.54
2
53.34
IN
2.10
.44 REF. TYP.
1.75 2.03
1.13 .68 MAX. 44.45 51.56
28.7 17.27 3.50
IN 1.80 REF. 88.9 .212 DIA.
MM 45.72 5.38
4.06 (2) MTG. HOLES
103.12
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
SE12V21 SE24V21
WARNING– ON MDCMODEL:EXCEEDING
1.0 AMPMAY DAMAGECIRCUIT
BOARD.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral MDC
Variable Flow Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
& impeller
• Shaded pole motor with ball bearings
OPTIONS
• Sealed blowers for contamination control
• Electronic speed control
50 60
NC
3 FEET (0.91 METERS) FROM NOISE SOURCE
50
db (re 0.0002 microbar)
Watts)
40 50
40
-12
db (re 10
30 40
30
20 30
63 125 250 500 1000 2000 4000 8000
OCTAVE BAND CENTERFREQUENCY Hz
11.0 11.0
10.0 Legend 10.0 Legend
Pressure: Pressure:
9.0 Suction: 9.0 Suction:
Minispiral MDC Minispiral MDC
8.0 8.0
Inches of Water
Inches of Water
7.0 7.0
32 V-MDC
mbar
mbar
6.0 6.0
15 V-MDC 26 V-MDC
5.0 5.0
24 V-MDC
4.0 12 V-MDC 4.0
3.0 3.0
2.0 9 V-MDC 2.0
1.0 1.0
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
Air Flow Rate - SCFM Air Flow Rate - SCFM
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F4
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral 12/24V HDC
Variable Flow Regenerative Blower
0.25
6.4
0.63
16.0
2.17
55.2
46.5
Ø 1.83
2.26
57.4
53.6
2.11
47.2
1.86
106.9
4.21
0.57 OD
1.14
29.0 0.67
14.5
0.54 17.0
0.92 13.7 1.65
0.57
14.5
0.75 OD
23.4 41.9
1.99 3.50
0.83
19.1
88.9
0.44
11.2
Part/Model Number
SE12RE21 SE24RE21
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral 12/24V HDC
Variable Flow Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
• 12 VDC operation: 7.5-15 VDC
• 24 VDC operation: 15-32 VDC
& impeller
• Brushless DC motor with integrated control electronics
• Stainless steel ball bearings permanently lubricated for B10 bearing life:
20,000 - 30,000 hours
• Weight: 1.9 lbs (0.86 kg)
• Envelope size: 4.18 x 1.83 inches (106.2 x 46.5 mm)
OPTIONS
• Sealed blowers for contamination control
• Electronic speed control
• Low voltage option
• International voltage and frequency (Hz)
50 60
NC
3 FEET (0.91 METERS) FROM NOISE SOURCE
50
EQUIVALENT SOUND PRESSURE LEVEL
db (re 0.0002 microbar)
40 50
SOUND POWER LEVEL
40
30 40
30
20 30
63 125 250 500 1000 2000 4000 8000
OCTAVE BAND CENTERFREQUENCY Hz
20 Legend 50
Pressure:
18 Suction: 45
Minispiral HDC
16 40
14 35
Inches of Water
15 V-HDC
mbar
12 30
12
10 V- 25
HD
C
8 20
9V
-HD
6 7.5 C 15
V-H
DC
4 LOW 10
VOLTAGE
2 OPERATION 5
0 1 2 3 4 5 6 7 8 9
Air Flow Rate - SCFM
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral 12V HDC Extra Flow / Extra Wide Fat Boy
Variable Flow Regenerative Blower
4.16 REF.
0.25
106.9
6.4
0.63
16.0
2.17
55.2
Ø 1.750
44.4
2.24
56.9
47.0
1.85
2.10
53.3
1.06
0.56 ID
26.9 0.67
14.2
0.53 17.0
0.92 13.5 1.65
0.56
14.2
19.1 TYP.
0.75 OD
Part/Model Number
SE12RE21A
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F7
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Minispiral 12V HDC Extra Flow / Extra Wide Fat Boy
Variable Flow Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
OPTIONS
• Sealed blowers for contamination control
• Electronic speed control
• Low voltage option
• Speed sensing output (FPS)
3 FEET (0.91 METERS) FROM NOISE SOURCE
50 60
NC
EQUIVALENT SOUND PRESSURE LEVEL
50
db (re 0.0002 microbar)
40 50
40
30 40
30
20 30
63 125 250 500 1000 2000 4000 8000
OCTAVE BAND CENTER FREQUENCY Hz
12
14 V- 35
HD
mbar
C
12 30
10 25
8 7.5
V-H 20
DC
6 15
4 10
LOW
2 VOLTAGE 5
OPERATION
0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F8
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Simplex SL2
Insrument Grade Regenerative Blower
.56 2.92
14.2 74.2
1/2" CONDUIT HOLE (1) EACH END
41.2
1.62
253.2
2.89
73.4
9.97
104.7
4.12
1.75 O.D.
44.5
3.31
84.1
126.2
4.98
OUT IN
1.60 I.D.
40.6
2.63 1.00
66.6 25.4
.25 -20 UNC -2B X .31 DEEP
(4 MOUNTING HOLES EACH END)
IN 3.00 TYP. 1.20 1.75
MM 76.2 30.5 44.5
NOTES 2.29
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING. 58.2
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F9
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Simplex SL2
Insrument Grade Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
OPTIONS
• International voltage & frequency (Hz)
• Hermetically sealed
• UL & CSA approved motor
• Remote drive (motorless) model
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
24 60 24 60
mbar
mbar
18 45 18 45
12 30 12 30
6 15 6 15
0 0 0 0
0 6 12 18 24 30 36 42 48 54 60 66 0 6 12 18 24 30 36 42 48 54 60 66
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 10
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Duplex SL4
Insrument Grade Regenerative Blower
6.56 MAX. 9.24
166.6 234.7
7.21 5.76
183.1 146.3
6.00 4.56 MAX.
152.4 115.8
CAPACITORS ON SINGLE
PHASE MODELS ONLY
1/2” CONDUIT HOLE
(1) EACH END
1.75 O.D.
1.60 I.D.
44.5
40.6
13.03 MAX.
331
OUT
1.62
41.2
104.7
9.89 DIA.
4.12
251.2
253.2
9.97
2.62
66.6
IN
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
SL4P2 SL4P52
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 11
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Duplex SL4
Insrument Grade Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
OPTIONS
• International voltage & frequency (Hz)
• Hermetically sealed
• UL & CSA approved motor
• Remote drive (motorless) model
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
40 100 40 100
mbar
mbar
30 75 30 75
20 50 20 50
10 25 10 25
0 0 0 0
0 8 16 24 32 40 48 56 64 72 80 88 0 8 16 24 32 40 48 56 64 72 80 88
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 12
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Duplex SL5
Insrument Grade Regenerative Blower
9.24
234.7
CAPACITORS ON SINGLE
PHASE MODELS ONLY
1/2" CONDUIT HOLE
(1) EACH END
1.75 O.D.
1.60 I.D.
40.6
44.5
13.03 MAX.
IN
104.7
1.62
41.2
9.89 DIA.
4.12
331
253.2
9.97
2.62
66.6
251.2
OUT
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
SL5P2 SL5P52
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 13
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
SPIRAL Duplex SL5
Insrument Grade Regenerative Blower
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
OPTIONS
• International voltage & frequency (Hz)
• Hermetically sealed
• UL & CSA approved motor
• Remote drive (motorless) model
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
•
24 60 24 60
mbar
mbar
18 45 18 45
12 30 12 30
6 15 6 15
0 0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 14
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Nautilair
A .495 (12.57)
K
B NC33A NC33AE9 NC33AG58
G (STD) (TEFC) (XP)
C V 11.55 11.55 11.55
X Z (4X) MTG HOLES A
(293.2) (293.2) (293.2)
KNOCKOUT FOR 0.28 DIA
6.07 6.07 6.07
AIRFLOW SWITCH B
(154.2) (154.2) (154.2)
5.38 (136.65)
(BOTH SIDES) J
U
0.495 0.495 0.495
D (REF)
N
M
O
(12.6) (12.6) (12.6)
11.3 (286.96)
L
Y
W 6.04 6.04 6.04
P
D
(153.4) (153.4) (153.4)
E
Ø5.19 (131.83)
F
(131.8) (131.8) (131.8)
4.25 4.25 4.25
1.75 (44.45) R S G
Ø.40 (108) (108) (108)
3.5 (88.90) 2.50 (63.50)
HOLE (4X) 0.25 0.25 0.25
AA H
(6.4) (6.4) (6.4)
T
TEFC MODEL J
1.75
(44.5)
1.75
(44.5)
1.75
(44.5)
5.10 5.10 5.10
K
(129.5) (129.5) (129.5)
3.13 3.13 3.13
L
(79.5) (79.5) (79.5)
4.75 4.75 4.75
A .495 (12.57) M
K (120.7) (120.7) (120.7)
B G 5.59 5.59 5.59
N
C V (142) (142) (142)
X Z (4X) MTG HOLES 5.90 5.90 5.90
H (TYP.) O
KNOCKOUT FOR 0.28 DIA (149.9) (149.9) (149.9)
AIRFLOW SWITCH 6.0 6.0 6.0
(BOTH SIDES) P
(152.4) (152.4) (152.4)
3.49 (88.75)
U
1.97 3.52 4.20
M
N
O
D
L R
Y (50) (89.4) (106.7)
1.23 (31.35)
W
2.78 2.78 2.78
E
S
(70.6) (70.6) (70.6)
F P (DIA. INLET)
Ø7.69 (195.28) 7.26 13.35 13.94
T
(184.4) (339.1) (354.1)
2.38 2.38 2.38
U
(60.5) (60.5) (60.5)
1.50 (38.10)
1.75 (44.45) 2.13 2.13 2.13
R S V
HOLES FOR ELECTRICAL CONNECTIONS (54.1) (54.1) (54.1)
3.50 (88.90) 2.53 (64.31)
2.96 2.96 2.96
1/4-20 UNC-2B X .50 DP. T W
(75.2) (75.2) (75.2)
(4) MTG HOLES EQUALLY
SPACED ON A 3.625 DIA. B.C. 0.84 0.84 0.84
X
(21.3) (21.3) (21.3)
1/4-20 UNC-2B X .50 DP.
(4) MTG HOLES 4.0 4.0 4.0
Y
(101.6) (101.6) (101.6)
2.5 2.5 2.5
IN STANDARD MODEL Z
(63.5) (63.5) (63.5)
MM
7.13
AA --- ---
(181.1)
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 15
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
Nautilair
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
80 90
3 FEET (0.91 METERS) FROM NOISE SOURCE
EQUIVALENT SOUND PRESSURE LEVEL –
70 80
db (re 0.0002 microbar)
SOUND POWERLEVEL –
db (re 10 -12Watts)
60 70
NC33
50 60
40 50
20 75 150 300 600 1200 2400 4,800
75 150 300 600 1200 2400 4800 10,000
OCTAVE BAND CENTERFREQUENCY Hz
4 10.0 4 10.0
mbar
2 5.0 2 5.0
1 2.5 1 2.5
0 0 0 0
0 50 100 150 200 250 300 350 400 450 500 550 0 50 100 150 200 250 300 350 400 450 500 550
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 16
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
DR 404/454/505/513/656
Spa Blowers
F L
GND LUG 1.021
25.9
165.1
6.50
G
IN E
IN T-BOX
0.42
MM
10.7
D 1/2-14 NPSM
NOTES THREAD
1 DRAWING NOT TO SCALE, CONTACT FACTORY "P" DIA
FOR SCALE CAD DRAWING. A I H
2-" NPSC (4) MTG
2 CONTACT FACTORY FOR BLOWER MODEL B
THREAD HOLES
LENGTHS NOT SHOWN.
C J
MODEL A (IN/MM) B (IN/MM) C (IN/MM) D (IN/MM) E (IN/MM) F (IN/MM) G (IN/MM) H (IN/MM) I (IN/MM) J (IN/MM) K (IN/MM) L (IN/MM)
DR404AQ58M 4.75/120.7 8.93/226.8 10.12/257 192/48.8 6.28/159.5 11.5/292.1 12.16/308.9 3.0/76.2 3.75/95.3 12.88/372.2 .59/15 12.91/327.9
DR454V58 4.75/120.7 10.30/261.6 11.38/289.1 1.92/48.8 6.98/177.3 12.55/318.8 13.52/343.4 3.25/82.6 4.50/114.3 10.81/274.6 .59/15 14.45/367
DR505AW58M 4.75/120.7 10.30/261.6 11.70/297.2 1.87/47.5 7.26/184.4 13.53/343.7 14.38/365.3 3.56/92.7 4.50/114.3 14.38/365.3 .59/15 15.0/381
DR513V58 4.75/120.7 11.42/290.1 13.0/330.2 2.23/56.6 8.69/220.7 14.21/360.9 15.8/401.3 3.72/94.5 5.50/139.7 13.74/349 .59/15 14.58/370.3
DR656K58X 4.92/125 11.42/290.1 12.8/325.1 2.25/57.2 7.46/189.5 15.42/391.7 15.17/385.3 4.14/105.2 5.5/139.7 15.12/384.1 .59/15 15.51/393.9
Part/Model Number
Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested
and certified to operate on both: 104-115/208-230 VAC-1 ph-60 Hz and 100-110/200-220 VAC-1 ph-50 Hz. All voltages above can handle a ±10% voltage
fluctuation. Special wound motors can be ordered for voltages outside our certified range.
Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated
motors or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature). Performance
curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 40°C.
Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or ambient
temperature reaches the maximum operating temperature.
Notes
- The blower should not be stopped/started more than four times an
hour. - Use of relief valve 515092 is required for all blowers.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 17
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
DR 404/454/505/513/656
Spa Blowers
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
(threaded)
• UL & CSA approved motor with permanently sealed ball bearings and
Class B rated thermal protection
•
• Quiet operation within OSHA standards
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
• Remote drive (motorless) models
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
• Variable frequency drive package
80 200 80 200
DR454 DR454
DR505 DR505
mbar
mbar
60 DR513 150 60 DR513 150
DR656 DR656
40 100 40 100
20 50 20 50
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 0 20 40 60 80 100 120 140 160 180 200 220
Temp Rise °C
Temp Rise °C
100 100
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
200 200
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
100 100
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 18
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
DR 10RDNT/SS10RDNT/HS 10RDNT
Remote Drive (Motorless) Blowers
Part/Model Number
1 DR10RDNT not recommended for use with explosive gas due to material of construction.
2 Maximum operating temperature: Blower outlet air temperature should not exceed 260°C (air temperature rise plus inlet temperature).
Contact factory for use above 260°C blower outlet air temperature.
3 AMETEK will not be liable for blowers operated beyond factory specific RPM.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 19
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
DR 10RDNT/SS10RDNT/HS 10RDNT
Remote Drive (Motorless) Blowers
FEATURES
• Manufactured in the USA - ISO 9001 and NAFTA compliant
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
PACKAGE/MOTOR OPTIONS
• International voltage & frequency (Hz)
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
mbar
mbar
90 50 ºC
225 90 75 º C 225
30 75 30 2500 RPM 75
1750 RPM
1750 RPM
0 0 0 0
0 75 150 225 300 375 450 525 600 675 750 825 0 75 150 225 300 375 450 525 600 675 750 825
Input
Input
20 3500 20
3500
2500 2500
1750 1750
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 20
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
MD 101 Magnetic-Drive
Regenerative Blower
ROTATION
3.00
76.2
Ø 9.84
249.9
2.62
66.5
1.69
42.9
1.88 Ø .28 MOUNTING HOLE
47.8 7.1
6.00 3.50
152.4 88.9
TEFC MOTOR
15.00 MD101CB4 MODEL SHOWN
381
4.12
104.7 INLET
OUTLET
1-11 1/2 NPT
2X
LEADS FAR SIDE .75-14 NPT
Ø 9.84
3.00
249.9
76.2
ROTATION
66.5
2.62
1.69
42.9
1.88 XP MOTOR
47.8 MD101CC4 MODEL SHOWN Ø .28 MOUNTING HOLE
IN 6.00 8.25
209.6 7.1
MM 152.4
3.50
16.6 88.9
NOTES 421.6
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
Part/Model Number
MD101CB4 MD101CC4
1 Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated motors
or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or
ambient temperatures above 40°C.
Rev. 2/04
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 21
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
MD 101 Magnetic-Drive
Regenerative Blower
FEATURES
• Hermetically designed seal-less blower
• Continuous operation
• Manufactured in the USA
BLOWER OPTIONS
• Corrosion resistant surface treatments & sealing options
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
•
25 62 25 62
20 50 20 50
Inches of Water
Inches of Water
AIR
AIR SG = 1.0
mbar
mbar
15 SG = 1.0 37 15 37
10 25 10 25
NATURAL GAS NATURAL GAS
SG = 0.56 SG = 0.56
5 12 5 12
0 0 0 0
0 3 6 9 12 15 18 21 24 27 30 33 0 3 6 9 12 15 18 21 24 27 30 33
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 22
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
GVR313
Regenerative Blower
10.50
266.7 14.19
360.4
95.3
3.75
ROTATION
11.38 (TYP.)
289.1
2.2
IN OUT
55.9
.34
.88 8.6
IN
124.5
4.9
22.4
MM
165.1
6.5
NOTES
1 DRAWING NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWING.
2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.
BOTTOM VIEW
3 GVR313AK4H MODELS SHOWN
Part/Model Number
1 115 voltage, 1 phase motors are standard. 230 volt motors available. As an option, a transformer could be used.
2 Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 140°C for Class F rated motors
or 120°C for Class B rated motors. Blower outlet air temperature should not exceed 140°C (air temperature rise plus inlet temperature).
Performance curve maximum pressure and suction points are based on a 40°C inlet and ambient temperature. Consult factory for inlet or
ambient temperatures above 40°C.
3 Maximum blower amps corresponds to the performance point at which the motor or blower temperature rise with a 40°C inlet and/or
ambient temperature reaches the maximum operating temperature.
Rev. 2/04
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 23
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Specific Blowers
GVR313
Regenerative Blower
FEATURES
• Manufactured in the USA
MOTOR OPTIONS
• International voltage & frequency (Hz)
BLOWER OPTIONS
ACCESSORIES
• Flowmeters reading in SCFM
• Filters & moisture separators
• Pressure gauges, vacuum gauges, & relief valves
50 125 50 125
40 100 40 100
Inches of Water
Inches of Water
GVR313
mbar
mbar
30 75 30 75
GVR313
20 50 20 50
10 25 10 25
0 0 0 0
0 5 10 15 20 25 30 35 40 45 50 55 0 5 10 15 20 25 30 35 40 45 50 55
Temp Rise °C
Temp Rise °C
50 50
0 0
Temperature curves are based on standard model Temperature curves are based on standard model
100 100
Temp Rise °C
Temp Rise °C
Blower Air
Blower Air
50 50
0 0
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 F 24
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
AMETEK Dynamic Fluid Solutions' ROTRON brand has long been a world leader in regen-
erative blower technologies, bringing regenerative advantages to a new level, providing quiet,
maintenance-free, oil-free operation.
Filtration Accessories
Measurement Accessories
Noise Reduction Accessories
Valves and Gauges
VFD Drives
Air Knives
SPECIFICATIONS:
HOUSING – Steel
C Ø
A Ø
MEDIA – Polyester
EFFICIENCY – 97-98% (8 to 10 micron particle size)
FILTER ELEMENT – Replaceable (see filter
elements) NOTE: “Z” MEDIA (1 to 3 micron particle
size) available
Part/Model Number
Specification Units 477411 516466 515122 515123 515124 515125 515145 515151 516511
Filter Element - A B C, D E E F G H H
Ref Blower Model - 271078 515132 515132 515133 515134 515134 515134 515135 516515
Outlet Connection - 2.00 SO 1.00 NPT 1.50 NPT 2.00 NPT 2.00 NPT 2.50 NPT 3.00 NPT 4.00 NPT 6.00 NPT
Inches 4.56 6.00 6.00 7.75 10.00 10.00 10.00 10.00 16.00
Dimension A
mm 115.8 152.4 152.4 196.9 254 254 254 254 406.4
Inches 6.12 6.50 6.50 7.25 12.25 12.50 13.00 14.00 15.00
Dimension B
mm 155.4 165.1 165.1 184.2 311.2 317.5 330.2 355.6 381
Inches 2.00 1.00 1.5 2.00 2.00 2.50 3.00 4.00 6.00
Dimension C
mm 50.8 25.4 38.1 50.8 50.8 63.5 76.2 101.6 152.4
Z Media Filter PN - 517865 517866 517867 517868 517869 517870 517871 517872
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
1258 Customer Service Fax: +1 215.256.1338
G1
www.ametekdfs.com ____
Accessories
Filtration - Inline Filter (Dual Connection)
MEDIA – Polyester
EFFICIENCY – 97-98% (8 to 10 micron particle size)
FILTER ELEMENT – Replaceable (see filter
elements) NOTE: “Z” MEDIA (1 to 3 micron particle
size)
* available
Feature 1/4" threaded tap for gauge connection on inlet and outlet D DIA.
Part/Model Number
Specification Units 271200 516461 515254 515255 515256 516463* 516465* 517611*
Filter Element - 271078 516434 516434 516435 516435 515135 515135 516515
Ref Blower Model - A B C, D E F G H H
Inlet Connection - 1.75 SO 1.00 NPSC-F 1.50 NPSC-F 2.00 NPSC-F 2.50 NPSC-F 3.00 NPT-M 4.00 NPT-M 6.00 NPT-M
Outlet Connection - 2.00 SO 1.00 NPSC-F 1.50 NPSC-F 2.00 NPSC-F 2.50 NPSC-F 3.00 NPT-M 4.00 NPT-M 6.00 NPT-M
Inches 5.25 7.25 7.00 8.00 8.00 14.00 14.00 18.00
Dimension A
mm 133.4 184.2 177.8 203.2 203.2 355.6 355.6 457.2
Inches 8.31 6.50 6.50 10.25 10.25 26.50 27.00 28.00
Dimension B
mm 211.1 165.1 165.1 260.4 260.4 673.1 685.8 711.2
Inches 2.00 1.00 1.50 2.00 2.50 3.00 4.00 6.00
Dimension C
mm 50.8 25.4 38.1 50.8 63.5 76.2 101.6 152.4
Inches 1.75 1.00 1.50 2.00 2.50 3.00 4.00 6.00
Dimension D
mm 44.5 25.4 38.1 50.8 63.5 76.2 101.6 152.4
Z Media Filter PN - 517886 517887 517888 517889 517890 517891 517892
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Filtration - Filter Silencers (Single Connection)
SPECIFICATIONS:
HOUSING – Steel
MEDIA – Polyester
A Ø
C Ø
EFFICIENCY – 97-98% (8 to 10 micron size)
FILTER ELEMENT – Replaceable (see filter elements)
Part/Model Number
Specification Units 516487 516489 516491 516493 516495 516497 516499 516513
Filter Element - B C, D E E F G H H
Ref Blower Model - 515132 515132 515133 515134 515134 515134 515135 516515
Outlet Connection - 1.00 NPT 1.50 NPT 2.00 NPT 2.00 NPT 2.50 NPT 3.00 NPT 4.00 NPT 6.00 NPT
Inches 6.00 6.00 10.00 10.00 10.00 10.00 12.33 16.00
Dimension A
mm 152.4 152.4 254 254 254 254 313 406.4
Inches 6.50 6.50 7.25 12.25 12.50 12.50 13.87 15.00
Dimension B
mm 165.1 165.1 184.2 311.2 317.5 317.5 352 381
Z Media Filter PN - 517878 517879 517880 517881 517882 517883 517884 517885
Inches 1.00 1.50 2.00 2.00 2.50 3.00 4.00 6.00
Dimension C
mm 13154101.2 13154126.6 13154152 13154177.4 13154202.8 13154228.2 13154253.6 13154279
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
1258 Customer Service Fax: +1 215.256.1338
G3
www.ametekdfs.com ____
Accessories
Filtration - Filter Element
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
1258 Customer Service Fax: +1 215.256.1338
G4
www.ametekdfs.com ____
Accessories
Filtration - Moisture Separator
applications.
H H
VACUUM GAUGE
(OPTIONAL) VACUUM GAUGE
(OPTIONAL)
VACUUM RELIEF
VALVE VACUUM RELIEF VACUUM GAUGE
G (OPTIONAL)
S E P A R AT OR
VALVE G
OUTLET
MOISTURE SEPARATOR
F
E
F
URE TM
CYCLONIC
ACTION
B
WATER LEVEL T OR
B
CAUTION:
E
E
F
J
FREEZING MAY CAUSE DAMAGE.
CAPACITY
MOISTURE SEPARATORS USED IN
TEMPERATURES BELOW 32øF (0øC)
MUST BE PROPERLY WINTERIZED.
B
INFO PACKET
3/4" 3/4"
J
NPT
J
NPT
D
D
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Filtration - Moisture Separator
5
Pressure Drop (IWG)
4
50BS
0PS
0BS
BS
MS200PS
BS
500
00
MS30
60
MS3
3
S1
MS
MS
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
Flow Rate (SCFM)
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Measurement - Air Flow Meter
FEATURES BENEFITS
• Direct reading in SCFM
• Low pressure drop (2-4" typical) across • OPTIMIZE SYSTEM EFFICIENCY
the flow meter Measuring the correct air ˜ow can
• Non-clogging, low impedance air stream assist you in ÿne-tuning to your
• Light weight aluminum system’s optimal efficiency.
• No moving parts
• Large easy-to-read dial • BALANCE MULTI-PIPING SYSTEMS
• Accurate within 2% at standard conditions When evacuating CFM from more than one
• Good repeatability pipe, di˝erent run lengths or end system
• Available in 2", 3" and 4" sizes impedance can cause one pipe to handle
• Factory conÿgured for quick installation more CFM than the other. With an accurate
• .048" Allen key supplied for gauge adjustment CFM reading, piping can be balanced by
bleeding air in/out or by creating an extra
OPTIONS impedance.
• Corrosion-resistant version with Chem-Tough • DETECT CHANNELING OR PLUGGING
™ or in stainless steel For systems in which channeling or
• FDA-approved Food Tough™ surface conversion plugging can occur, a change in the CFM
measured can help indicate the unseen
changes in your system.
Part/Model Number
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G7
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Measurement - Air Flow Meter
3.75 PR E
S S URE 30
P. S.
A X I.
M G.
ØF
2.87
1.75
DIA. 210 280
140
070
S S URE
PRE 30
P. S.
A X I.
350
M G.
140
210 280
B
070 350
3.75
3.5
REGENERATIVE BLOWER GROUP
MINIHELIC II
MINIHELIC II
FLOW DIRECTION C
2.0
5.56
TYPICAL GAUGE FACE
MOISTURE SEPARATOR
E R U T S IO M
SYSTEM PIPING
MT
RO TA R A P ES
BLOWER
S SU
E R E 30
X PR .
P S. .
M A I G.
210 280
140
070 350
AMETEK
ROTRON T.I.P.
TECHNICAL & INDUSTRIAL PRODUCTS
MINIHELIC II
SCFM 1
√( ) (
IN OUT
SCFM 2 =
14.7
Pf 2
x
530
Tf 2 + 460 )
Pf 2 = Absolute Pressure in ROTRON’S ˜ flow meter is a venturi style design.
PSIA Tf2 = Temperature in °F After air enters the inlet, the pressure is
measured in the P1 tap. The second tap, P2,
measures the pressure at the throat. The
differential between P1 and P2 registers across
• Use on inlet to limit need to correct for high a special calibrated CFM gauge to provide
pressure or elevated outlet temperature accurate readings. The throat is then expanded
back to the original size to keep pressure loss to
• Standard model limits = 140°F and 30 PSIG under
2-4 IWG.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G8
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Measurement - Digital Flowmeter
Remote air flow rate monitoring and system automation control can now be achieved through the use of 4-20 mA output signals.
Our 4-20 mA analog outputs are proportional to system flow rates and can be used with PLC controlled operations to monitor
system performance. Those same outputs provide digital displays for direct readings in SCFM when paired with our LCD Digital
Readout option. Combined with our Variable Frequency Drives, you can now achieve a completely automated system capable of
adjusting blower performance to meet changing system demands. Maintaining your system at peak performance gives your
company the competitive edge needed in today’s marketplace.
Ø.16 (2X)
DIFFERENTIAL PRESSURE TRANSMITTER MOUNT HOLES
1.00
2.75
3.16
3.50
Suitable for remote mounting up to 10' form flow
LOW
Note 2: Use 5/16" OD stiff wall tubing-connect "Lo" on flowmeter to "Lo" on 4-20 mA
enclosure, "Hi" on flowmeter to "Hi" on 4-20 mA enclosure. Tubing must be equal in
length. (Maximum length is 1o feet)
LCD DISPLAY
FM20L030Q FM20L045Q FM20L065Q FM20L125Q FM20L175Q FM20L225Q FM30L250Q FM30L350Q FM30L475Q FM40L450Q FM40L600Q FM40L850Q
550860 550861 550862 550863 550864 550865 550866 550867 550868 550869 550870 550871
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G9
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Noise Reduction - Sound Attenuating Enclosure
15.00
46.00
50.00
Part/Model Number
SAE30W72F SAE36W72F
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 10
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Noise Reduction - Inlet/Outlet Muffler (Single Connection)
SPECIFICATIONS:
HOUSING – Steel
MEDIA – Acoustical Material
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 11
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Noise Reduction - Inline Muffler (Dual Connection)
or outlet of blower.
Part/Model Number
Specification Units 550888 522948 529900 551377 515185 511569 515210 551565 516264
Ref Blower Model - D E E E F G G G H
Inlet Connection - 1.5 NPT-M 2.0 NPT-M 2.0 NPSC-F 2.0 NPT-M 2.5 NPT-M 3.0 NPT-M 4.0 NPT-M 4.0 NPT-M 4.0 NPT-M
Outlet Connection - 2.0 NPT-F 2.0 NPSC-F 2.0 NPSC-F 2.0 NPT-M 2.5 NPT-F 3.0 NPT-F 4.0 NPT-F 4.0 NPT-M 4.0 NPT-F
Inches 4.00 4.00 4.38 4.00 6.12 7.00 10.00 10.00 8.00
Dimension A
mm 101.6 101.6 111.3 101.6 155.4 177.8 254 254 203.2
Inches 7.75 15.75 15.75 15.75 15.00 18.00 24.00 24.00 22.00
Dimension B
mm 196.9 400.1 400.1 400.1 381 457.2 609.6 609.6 558.8
Inches 15.5 18.45 18.45 18.15 19.00 22.25 30.00 30.00 27.75
Dimension C
mm 393.7 468.6 468.6 461 482.6 565.2 762 762 704.9
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 12
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Protection - Relief Valve - Mechanical
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts
typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual
performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the
right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products
Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS G 13
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 ____
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com
Accessories
Protection - Pressure Regulating Diaphram Valve
Fig. 1 Fig. 2
C
C
The PRD Valve is installed to prevent excessive SEE
NOTE
system pressure or vacuum that could result from DIFFERENTIAL
line restrictions. Valves should be installed at the ADJUSTMENT
SCREW
blower outlet (downstream) in pressure systems
and at blower inlet (upstream) in vacuum systems. D
GAUGE
These valves are suitable for air, natural gas, D
B PORT
propane, and other non-corrosive service.
GAUGE B
PORT
Note: PRD valves are not factory preset, but are
easily field adjustable.
A
SPECIFICATIONS: PRESSURE RELIEF: B is the system port and A is the vent or atmospheric port.
A
VALVE BODY – Aluminum (1"), Cast VACUUM RELIEF: A is the system port and B is the vent or atmospheric port. For vacuum
Iron (2") VALVE SPRING – Steel mode, customer must remove snap ring and screen.
DIAPHRAGM – Nitrile NOTE: Replace cap after adjusting setting. Valve will not operate with cap removed.
Differential adjustment screw is under the cap.
Part/Model Number
Specification Units 515092 529612 529857 529858 551130 515093 529859 550246 550247
in. H2O 27-125 110-415 277-554 7-18 14-62 48-194 110-277 97-197 97-194
Range
mbar 67.3-311.4 274-1033.8 690-1380 17.4-44.8 34.9-154.4 119.6-483.3 274-690 241.6-490.7 241.6-483.3
Description - Fig 1. Fig 1. Fig. 1 Fig. 2 Fig. 2 Fig. 2 Fig. 2 Pressure Vacuum
Ref Blower Model - B, C, D, E B, C, D, E B, C, D, E F, G F, G F, G F, G H H
Inlet Connection - 1 1 1 2 2 2 2 2.5 2.5
Outlet Connection - 1 1 1 2 2 2 2 2.5 2.5
Inches 1.00 1.00 1.00 2.00 2.00 2.00 2.00 2.50 2.50
Dimension A
mm 25.4 25.4 25.4 50.8 50.8 50.8 50.8 63.5 63.5
Inches 1.00 1.00 1.00 2.00 2.00 2.00 2.00 2.50 2.50
Dimension B
mm 25.4 25.4 25.4 50.8 50.8 50.8 50.8 63.5 63.5
Inches 4.12 4.12 4.12 7.12 7.12 7.12 7.12 6.19 6.19
Dimension C
mm 104.6 104.6 104.6 180.8 180.8 180.8 180.8 157.2 157.2
Inches 8.70 8.70 8.70 9.00 9.00 9.00 9.00 7.65 7.65
Dimension D
mm 221 221 221 228.6 228.6 228.6 228.6 194.3 194.3
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 14
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Protection - Gauges
rugged.
100
60
3
12
2 PRESSURE 4
0
40
SPECIFICATIONS:
140
1 5
20
16
0 6
0
0
P S I
ER
in Black Enamel LENS – Glass
I NC
HE S OF WAT
DIAPHRAGM – ACCURACY– 1%
Bronze LENS – Clear WEIGHT – 1/4 lb.
Plastic ACCURACY– CONNECTION – 1/2"
2%WEIGHT – 1/2 lb. NPT FACE – 3" Dial
CONNECTION – 1/4"
NPT FACE – 2 1/2" dia.
3.38 ±.12
100 120
2.50 ±.06
80
200 .25 ±.03
14
250
0
Ø 3.18 ±.12
150 300
60
160
100 350
40
180
50 °F 400
20
0
10 20
1/2 NPT CONNECTION
°C
Temperature
Part/Model Number
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 15
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
System - Variable Frequency Drive
A Variable FrequencyDrive (VFD)is an adjustable speedAC motor control designed to speed the
blower RPMup or down. Our VFDsare designed to minimize losses and deliver increased
efficiency, low maintenance, and the long life expected from the ROTRON product line.
FEATURES
•
ncy by controlling motor RPMs
• Accepts 3Ø or 1Ø inputs to drive 3Ø motor blower
assemblie
• Accepts
s 4-20 mA, 0-5 VDC or 0-10 VDC inputs for
system automation control and intregation
• Provides dynamic breaking capabilities
• Replaces motor starter function
• Digital readout in either Hz or RPMs
• Keypadenclosure(NEMA4X-Indoor) vsn be
mounted up to 100' from controller with cable
assembly option
SYSTEM REQUIREMENTS
• In cases where the distance between the controller
and motor exceed 50', the use of a line reactor on
load side is needed.
• XP motors must be UL listteedd for use with a
Variable Frequency Drive.
VARIABLE FREQUENCY DRIVE SELECTION
Thereare some common guidelines in sizing a VFDfor use on a AMETEKROTRONblowers such as the allowable
speed(table 1) for a given motor type. To determine the required RPM to achieve a desired flow and pressure
form a specific bloewr, turn to the blower performance at variable speeds in section E of this catalog. The
required RPM must fall within the allowable rate of the motor being used.
Table 1
Motor Allowable Turndown Allowable Speedup
Standard 3600 RPMto 1800 RPM —
3600 RPMto 900 RPM —
Inverter Motor 3600 RPMto 360 RPM* 3600 RPMto 7200 RPM
* Turndown of 10:1 is not typically done with regenerativeblower designs.
For all applications above 3600 RPM, contact your Field Sales Engineer for proper horsepower sizing.
Specification
L L
3.15 3.15
TYP. TYP.
.25-20 UNC X .75 LG
Part/Model Number
AK06S060 AK12S060 AK18S060 AK24S060 AK30S060 AK36S060 AK42S060 AK48S060 AK54S060 AK60S060
Specification Units 523489 552955 522949 553000 522950 523492 523493 523494 523495 523496
Inches 9.30 15.30 21.30 27.30 33.30 42.30 48.30 54.30 60.30 66.30
Length (L)
mm 236.2 388.6 541 693.4 845.8 1074.4 1226.8 1379.2 1531.6 1684
Inches 6 12 18 24 30 36 42 48 54 60
Slot Length
mm 152.4 304.8 457.2 609.6 762 914.4 1066.8 1219.2 1371.6 1524
Inches 4.00 10.00 16.00 22.00 28.00 17.00 20.00 23.00 26.00 29.00
Dimension S
mm 101.6 254 406.4 558.8 711.2 431.8 508 584.2 660.4 736.6
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 17
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
System - Air Knives
Air Velocity
30,000 FPM
DR656
25,000 FPM
DRP13
20,000 FPM
DR14
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800
SCFM
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 18
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
System - 5 Way, 3 Port, 2 Position Diverter Valve
SPECIFICATIONS:
• Aluminum body and spool assembly
• 303 stainless steel shaft
• 115 V-60 Hz solenoid valve air
OPTIONS
• Corrosion resistant surface treatments
• International voltage and frequency (Hz)
• Application specific designs
DR 505 BLOWER WITH DIVERTER VALVE
These unique solenoid actuated diverter valves The principle behind ROTRON’s diverter valve system is a
automatically change air piping from pressure to simple one: Some applications such as vacuum part pick-up, air
suction; greatly enhancing blower versatility and tables, and pneumatic tube systems require both vacuum and
productivity. This valve is effective in blower pressure in their equipment’s operation, but not simultaneously.
applications that require frequent switching from They eliminate the need for two sep-arate blowers, and
pressure to suction and vice-versa. They are cost elaborate valving system, or cycling/reversing a spinning
effective as applications normally requiring two blower impeller. ROTRON’s diverter valve changes the air
blowers and/or intricate piping systems may be passageways. By utilizing the side vent ports for incoming or
accomplished with one blower. outgoing air, the equipment/piping side of the valve changes
Diverter valves may be purchased as blower/valve from vacuum to pressure and back again by a signal sent to the
assemblies, or as separate stand-alone valve solenoid coil.
assemblies for use in other switched air applications.
Part/Model Number
Blower
BLOWER SIDE Blower
D C
IN OUT IN OUT
E WORKING
G PART
A
SOLENOID SOLENOID
F SUCTION PRESSURE
B
"PRESSURE" AIR PATH "SUCTION" AIR PATH
EQUIPMENT/PIPING SIDE ISO VALVE DRAWING DE-ENERGIZED POSITION ENERGIZED POSITION
Consult factory for proper selection and application.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 19
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
System - 5 Way, 3 Port, 2 Position Diverter Valve
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 20
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Accessories
Pressure & Vacuum Arrangements
Pressure or vacuum guages should be located in the delivery Failure to observe these precautions can result in false
line, oriented as shown. Assure that the guage is approxi- readings of guages and failure of the relief mechanism to
mately three pipe diameters from the blower delivery flange protect the blower from overload.
and that the relief valve is located at the same spacing from
the guage. 90° elbows should be located at least five pipe In order to avoid overheating or distortion of PVC pipe,
diameters from the blower delivery flange. Elbows, taps, tees, the first five to eight feet from the blower delivery flange
valves, or other restrictions to air flow should not be located on pressure systems should be metal.
between the blower delivery flange and accessories described
above.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 G 22
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
ROTRON strives to provide the most complete variety of desired Chemical Processing (CP) features are added to TEFC, XP or HiE
options on our products including on our motors. By using designs for corrosive gas service, Marine Duty service and
motor vendors of high quality and versatility, we can provide sanitary (food/pharmaceutical) service.
motor features from multiple released designs to meet your
needs (i.e., a Chem Processing Inverter Duty Explosion-proof • 303 stainless steel shaft
motor with space heaters and drains wound for 380 V-50 Hz
service). • Cast iron and steel frame epoxy painted or zinc plated
ROTRON motors are engineered for us to integrally mount with • Stainless steel nameplate
our blower and maximize blower performance. Our vendors are
qualified by ROTRON (per motor part number) to ensure the • Non-hygroscopic insulation; double dipped and baked stator
blowers’ mechanical and electrical needs merge with your
required features. The basic motor requirements on our • Epoxy coating on rotor
DR/EN/CP/HiE products include:
• Gaskets and joint sealers on all metal-to-metal surfaces
• NEMA approved
• Oversized conduit box
• CE conformity (non-XP models)
High Efficiency (HiE) features are added to TEFC, ODP, XP or CP
• UL & CSA approved with symbol and file on nameplate motors for maximum motor efficiency and life. ROTRON HiE
motors carry extra phase-to-phase protection for use with
• C-face mount inverters between a 1750-3500 RPM range.
• Permanently sealed bearings Inverter Duty features are added to TEFC, ODP, XP or CP for use
with Inverters/Variable Speed Drive Controllers. A wide range
• Shaft end play, run out and perpendicularity requirements of RPM can be handled and should be specified at time of
above NEMA standards quote. For best compatibility, an inverter should be matched to
the motor manufacturers design.
• Dual voltage and dual frequency (some models not feasible)
to maximize use worldwide Project Specific Motor Variations
• Single Shafted Totally Enclosed Fan Cooled (TEFC) and There are no limits to the options you can select or request for
Explosion-proof (XP) models your product. Routine motor options include:
• Double Shafted Open Drip Proof (ODP) models with dual • International voltage & frequency (Hz)
internal fans for circulation
• Different shaft material
• Class I Group D minimum on explosion-proof motors; many
are Class I Group D, Class II F & G • Oversized and/or Nema 4 intent T-box
• Regreasable bearings
• Tropicalized windings
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
The containment option utilizes a series of O-rings to control gas leakage in Spiral blower models. The O-rings are placed at critical
locations on the blower’s housing and covers to contain gas leakage.
On DR, EN and CP 101 units, a magnet drive option has been an alternative for complete gas containment.
O-rings are used throughout the product, and magnets attached to the motor shaft spin magnets inside the blower without shaft
penetration. Estimated leakage rate = 0.001 cc/mi
Nitrogen Purge / Blanket Option
The nitrogen purge option is a carrier designed to accept a nitrogen line which will purge the space outside the shaft hole. Purges can
be designed to bleed the nitrogen into the process called a blanket, or the carrier can have a second tap to carry away the leaking
contaminants.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
To stand up in corrosive and hazardous environments, chemical Chem-Tough™ employs the advantages of anodizing, hardcoat
processing blowers have to be tough. That’s why Ametek plating, low-friction polymers and dry lubricants to become an
ROTRON routinely applies Chem-Tough™, ROTRON’S own integral part of the blower’s molecular structure.
engineered and proprietary process, whenever it builds
blowers for handling chemical (vapor) streams. Chem-Tough™ Specifically, Chem-Tough™ first converts the aluminum surface
combines the advantages of aluminum oxide ceramic and to aluminum oxide, forming a new ceramic-like surface. The
selected fluorocarbons to give ROTRON blowers unheard-of water in the ceramic is replaced with Teflon®, adding a multi-
levels of chemical resistance, hardness, abrasion resistance, functional dimension to the surface; in the process, the
permanent lubricity and more. aluminum crystals expand and form anchor crystals that
remain hygroscopic for a short time. Then, under controlled
Chem-Tough™ Brings You the Rotron Advantage conditions, particles of the specified polymer are infused to
interlock with these anchor crystals. The new surface extends .5
Through this unique proprietary process, Chem-Tough™ gives mil above and below the original aluminum surface – and
ROTRON blowers these advantages: forms a permanent molecular bond with the metal.
• Outstanding Chemical Resistance The result: a plastic/ceramic surface that’s harder than steel, is
Time after time, Chem-Tough™ finishing shows extremely high continuously lubricating, and resists damage from chemicals
resistance to most common chemicals, as well as dramatically like no other. The kind of protection you need for your
improved corrosion resistance over regular hard anodizing. chemical processing blowers.
Chem-Tough™ allows aluminum to achieve equivalent
corrosion resistance as teflon®. 90-day immersion in acid or
alkaline solution (pH 4.0-8.5) has no effect; neither does
prolonged exposure to salt water. Far exceeds military
specification requirements for salt spray.
• Increased Hardness
With an equivalent hardness of Rc 40-60, Chem-Tough™ is
approximately file-hard – the hardness of nitrated steel.
Because the Chem-Tough™ surface becomes an integral part
of the metal, it simply cannot peel or chip – neither can it be
scratched, flaked or nicked under ordinary conditions.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
Chem-Tough (Teflon®)
Chem-Tough (Teflon®)
A – No effect – acceptable
Carbon Steel
Carbon Steel
D – Severe effect – not recommended
Hastelloy C
Hastelloy C
Aluminum
Aluminum
Cast Iron
Cast Iron
* – Not tested
Chemical Chemical
Acetaldehyde B * C A A A A * A Barium Carbonate B B B A B A A A A
Acetate Solv. B B A A A B A B * Barium Chloride D D C A C A A A A
Acetic Acid B D C A * B A B A Barium Hydroxide D C C A B C A A B
Acetic Anhydride B B D A B A A B A Barium Sulfate D C C A B A A A A
Acetone A A A A A A A B A Barium Sulfide D C C A B A A * *
Acetylene A A A * A A A A * Benzaldehyde B B A A A A A * A
Acrylonitrile B C * * A A C * B Benzene B B C A B A A A B
Alcohols Benzoic Acid B D * A B A A A A
Amyl C C C A A A A * A Benzol B * * A * A A * A
BENZYL B * * * * A A * A Borax (Sodium Borate) C A C A * A A A A
Butyl B C C A A A A * A Boric Acid B D * A B A A A A
Diacetone A * A * * A A * A Bromine (Wet) D D D A D D D D A
Ethyl B A A * * A A A A Butadiene A C C A A A A * *
Hexyl A * A * * A A * A Butane A C C A A A A * *
Isobutyl B * A * * A A * A Butanol A * * A * A A * A
Isopropyl B C A * * A A * A Butylene A A A A A * A * *
Methyl B A A A * A A A A Butyl Acetate A * A A * * C * A
Octyl A * A * * A A * A Butyric Acid B D * A B B A A A
Propyl A * A A * A A * A Calcium Bisulfate D D * A C D A * *
Aluminum Chloride 20% B D A * * D C D A Calcium Bisulfide C * * A * * B * A
Aluminum Chloride D D B A C D C * A Calcium Bisulfite C * * A * D A * A
Aluminum Hydroxide A D A A * A A A * Calcium Carbonate C D * A B A A A A
Alum Potassium Calcium Chloride C C * A C A D C A
Sulfate (Alum), 10% A D A A * A * * B Calcium Hydroxide C * * A B A A * A
Alum Potassium Calcium Hypochlorite C D * A D A C C B
Sulfate (Alum), 100% B * A A * D A B B Calcium Sulfate B * * A B A A A B
Aluminum Sulfate A D A A * C C A A Carbon Bisulfide A B * * B A A A *
Amines A A B A A A A * A Carbon Dioxide (Wet) C C * A * A A * A
Ammonia 10% * * * A * * A * A Carbon Disulfide C B C A * B A * *
Ammonia, Anhydrous B D B A A B A A A Carbon Monoxide A * * * * A A * *
Ammonia, Liquids D A A A * A A A B Carbon Tetrachloride C C D A B C B A A
Ammonia, Nitrate C * A * * A A A * Carbonated Water A D * * B A A A *
Ammonium Bifluoride D * * * * C A * B Carbonic Acid A D * A B A B A A
Ammonium Carbonate C C B A B A A A B Chloracetic Acid C D * A D D D D A
Ammonium Chloride C D D A C A C A A Chlorinated Glue D D * * * A A * *
Ammonium Hydroxide C A C A A A A A A Chlorine, Anhydrous Liquid D C * A * D D D A
Ammonium Nitrate B A D A A A A A A Chlorine (Dry) D A * A B A A * A
Ammonium Persulfate C D A A * A A A A Chlorine Water D D * A D * D * B
Ammonium Phosphate, Dibasic B * D A B A A A A Chlorobenzene (Mono) B B C A A A A * A
Ammonium Phosphate, Monobasic B * A A * A A A A Chloroform D D C A A A A A A
Ammonium Phosphate, Tribasic B C D A B A A A A Chlorosulfonic Acid D * D A D D * D B
Ammonium Sulfate B C C A C A B A A Chlorox (Bleach) C D C A * A A * A
Amyl-Acetate B * C A B A A C A Chromic Acid 5% C D * * * A A B A
Amyl Alcohol B * A A * A A * A Chromic Acid 50% C D * A C B B * A
Amyl Chloride D * A A * C B * A Citric Acid C D * A * A A A A
Aniline C * C A B A A A B Citric Oils C * * * * A A * *
Anti-Freeze A B C A * A A * A Copper Chloride D D * A C D D B A
Antimony Trichloride D * * A * D D * A Copper Cyanide D D * A * A A A A
Aromatic Hydrocarbons A A A * * * A * * Copper Floborate D D * A * D D * B
Arsenic Acid D D D A B A A * * Copper Nitrate D * * A B A A B A
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H4
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
Chem-Tough (Teflon®)
Chem-Tough (Teflon®)
A – No effect – acceptable
Carbon Steel
Carbon Steel
D – Severe effect – not recommended
Hastelloy C
Hastelloy C
Aluminum
Aluminum
Cast Iron
Cast Iron
* – Not tested
Chemical Chemical
Copper Sulfate (5% Solution) D D * A * A A A A Hydrofluoric Acid 100% D D D A D D D * B
C re s ols B * * * * A A * * Hydrofluosilicic Acid (20%) D D * A * D D * B
C re s ylic A c id C * * A B A A * B Hydrofluosilicic Acid C * * A * D D * C
C yc lohe x a ne A * A * * A * * * Hydrogen Gas A B B A A A A * *
D e te rge nts A * A * * A A * * Hydrogen Peroxide 10% A D * A * C C * A
D ie s e l F ue l A A A * A A A * * Hydrogen Peroxide A D D A * A B A A
D ie thyla mine A * * A A A * * * Hydrogen Sulfide,
D ye s B * * * * A A * * Aqueous Solution C D * A * A A C A
Epsom Salts (Magnesium Sulfate) A * * * B A A A B Hydrogen Sulfide (Dry) D B B A A C A * A
E tha ne A * * * A A * * * Hydroxyacetic Acid (70%) D * * * * * * * *
E ther A * B * A A A A B Ink C D D * A A A * *
E thyl A c e ta te B * C A * A A * B Iodine D D * A * D D D B
E thyl C hloride B C D A * A A A B Iodoform A C B A B D A * *
Ethylene Chloride C C C A * A A * B Isotane A * * * * * * * *
Ethylene Dichloride D * C A * A A * B Isopropyl Acetate C * * * * * B * *
Ethylene Glycol A B C A * A A * A Isopropyl Ether A * A A A * A * *
Ethylene Oxide A * * A * * A * * Jet Fuel (JP3, JP4, JP5) A A A A A A A * *
F a tty A c ids B D * A * A A * A Kerosene A A B A A A A A A
F e rric C hloride D D * A * D D D B Ketones B A A A A A A * A
Fer ric Nit rate D * * A * A A A A Lacquers A C C * A A A * *
F e rric S ulfa te D D * A * A C A A Lactic Acid C D D A A A B C A
Ferrous Chloride D D * A * D D * B Lead Acetate D * D A B A A * A
Ferrous Sulfate D D D A B A C * B Lubricants A * * A * A A * A
F luorine D D D C D D D * A Magnesium Chloride D D C A B B B A A
F luos ilic ic A c id D D * A * * B * B Magnesium Hydroxide D B B A A A A * A
F orma lde hyde A D A A A A A * B Magnesium Sulfate B C B A B B A * B
F ormic A c id D D D A C A B B A Maleic Acid B * B A C A A A A
F re on 11 B C B A A * A * * Malic Acid C * D A B A A * A
Freon 12 (Wet) B * * A * * D * * Mercuric Chloride (Dilute Solution) D D D A D D D D B
F re on 2 2 B * * * * * A * * Mercuric Cyanide D * D A A A A * *
F re on 11 3 B * * * * * A * * Mercury C A A A A A A A A
F r e o n T. F . B * * * * * A * * Methane A A A A A A A A A
F ue l O ils A C B A A A A * A Methyl Acetate A * B A A * A * A
F ura n R e s in A A A A * A A * * Methyl Acetone A A A A A * A * *
F urfura l A * A A A A A * B Methyl Alcohol 10% C * B A A * A * A
G a llic A c id A D D A B A A * A Methyl Butyl Ketone A * * * * * A * *
G a s oline A A A A A A A A A Methyl Cellosolve A * * * * * * * *
G lyc e rine A B B A A A A A A Methyl Chloride D * * A * C A * A
H e pta ne A * B A A * A * A Methyl Ethyl Ketone A * * A * A A * A
H e x a ne A * B A A A A * A Methylamine A B B * A * A * *
Hydraulic Oils (Petroleum) A A A A A A A * * Methylene Chloride A * B A A A A * A
Hydraulic Oils (Synthetic) A A * * * A A * * Naptha A B B A A A A A A
Hydrobromic Acid D D D A D D D D A Napthalene B B A A B A B * A
Hydrochloric Acid (Dry Gas) D * D A D C A * A Nickel Chloride D D * A * A B * A
Hydrochloric Acid (20%) D D * A * D D D B Nickel Sulfate D D D A B A B * B
Hydrochloric Acid (37%) D D * A * D D D B Nitric Acid (10% Solution) D D D A A A A A A
Hydrochloric Acid 100% D D * A * D D * C Nitric Acid (20% Solution) D D * A * A A A A
Hydrocyanic Acid A * C A A A A C A Nitric Acid (50% Solution) D D * A * A A A A
Hydrofluoric Acid (20%) D D * A * D D D B Nitric Acid
Hydrofluoric Acid (75%) D D * A * C D * C (Concentrated Solution) B D * A * D B A B
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Motor Blower Options
Chem-Tough (Teflon®)
Chem-Tough (Teflon®)
A – No effect – acceptable
Carbon Steel
Carbon Steel
D – Severe effect – not recommended
Hastelloy C
Hastelloy C
Aluminum
Aluminum
Cast Iron
Cast Iron
* – Not tested
Chemical Chemical
Nitrobenzene C B B A B A B * B Sodium Hydrosulfite A * * A * * * * A
Oleum B * B A B * A * * Sodium Hydroxide (20%) D A * A * A A A A
Oxalic Acid (cold) C D D A C A B A B Sodium Hydroxide (50% Solution) D B * A * A B * A
Pentane A B B A A C C * B Sodium Hydroxide (80% Solution) D C * A * A D * B
Perchloroethylene A B B A B A A * * Sodium Hypochlorite (to 20%) D C * A * A D * B
Petrolatum B C C A A * A * * Sodium Hypochlorite D D D A D * A * A
Phenol 10% A B D A B A A * B Sodium Hyposulfate D * * A * A A * *
Phenol (Carbolic Acid) B D D A B A A A A Sodium Metaphosphate A B B A A * A * *
Phosphoric Acid Sodium Metasilicate B C C A A * A * *
(to 40% Solution) D D * A * B A A A Sodium Nitrate A A B A B A A A B
Phosphoric Acid Sodium Perborate B B B A B * C * *
(40%-100% Solution) D D * A * C B B A Sodium Peroxide C D C A B A A * B
Phosphoric Acid (Crude) D D D A * D C C A Sodium Polyphosphate
Phosphoric Anhydride (Molten) D * * A * A A * * (Mono, Di, Tribasic) D * * A * A A * A
Photographic (Developer) C D * * * C A C A Sodium Silicate C * B A B A B A B
Phthalic Anhydride B C C A B A B * A Sodium Sulfate B A B A B A A C B
Picric Acid C D D A B A A * A Sodium Sulfide D A B A B A B * B
Potash C B * * * A * A A Sodium Sulfite C A * A * C C * A
Potasium Bicarbonate C D * A * A * B B Sodium Thiosulphate (“Hypo”) B C B A A A A * *
Potassium Bromide C D D A A A * B B Stannic Chloride D D D A D D D * B
Potassium Carbonate C B B A B A * A A Stannous Chloride D D D A D D C * A
Potassium Chlorate B B B A B A A A B Stearic Acid B C C A B A A A A
Potassium Chloride B B B A C A A B A Stoddard Solvent A B B A A A A A A
Potassium Chromate A A * * * * B B B Styrene A * A A A A A * *
Potassium Cyanide Solutions D B B A B A B A A Sulfate Liquors B * * * * C C * A
Potassium Dichromate A B C A B A A A B Sulfur Chloride D * * A * D D D *
Potassium Ferrocyanide C * C A B A * A B Sulfur Dioxide A * * A * A A C B
Potassium Hydroxide (50%) D C A A A B B B A Sulfur Dioxide (Dry) A A B A A A A * A
Potassium Nitrate B * B A B A B A B Sulfur Trioxide (Dry) A B B A A A C * *
Potassium Permanganate B B B A B A B B B Sulfuric Acid (to 10%) C D * A * D C C A
Potassium Sulfate A B B A B A B B A Sulfuric Acid (10%-75%) D D * A * D D D B
Potassium Sulfide B B B A A A * A B Sulfurous Acid C D D A C C B C B
Propane (Liquified) A * B A A A * A * Tannic Acid C C C A B A A A B
Propylene Glycol A B B A B B * A * Tanning Liquors C * * A * A A * A
Pyridine B B A A * C * B * Tartaric Acid C D D A B A B B B
Pyrogallic Acid B B B A B A A A A Tetrahydrofuran D D A A * A A * *
Silver Bromide D * * * * C C B * Toluene, Toluol A A A A A A A * A
Silver Nitrate D D D A B A B A A Trichlorethane C C * A * C A * A
Sodium Acetate B C C A B A A B A Trichlorethylene B C B A B A A * A
Sodium Aluminate C * C A B * * A B Water, Acid, Mine C C * * * A A * *
Sodium Bicarbonate A C C A B A A A * Water, Distilled, Lab Grade 7 B D * A * A A * *
Sodium Bisulfate D D D A A A * A B Water, Fresh A B D A A A A * *
Sodium Bisulfite A D * A * A * A B Water, Salt B D * * * A A * *
Sodium Borate C C C A B A * A A Weed Killers C * * * * A A * *
Sodium Carbonate C B B A B A B B A Whiskey and Wines D D D A A A A A *
Sodium Chlorate B * C A B A * A B Xylene A A B A A A A * A
Sodium Chloride C B C A B A C B A Zinc Chloride D D D A D A B B B
Sodium Chromate D B B A A A A * B Zinc Hydrosulphite D D * * * * A * *
Sodium Cyanide D B B A B A * A * Zinc Sulfate D C D A B A A A B
Sodium Fluoride C D D A B C * C A
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 H6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
Throughout our catalog, you will find terminology used for air moving selection and product sizing. Below are a few of the key terms:
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I1
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I2
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I3
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
Specific Gravity and Density of Various Gases at 60°F (1 ATM) Temperature Conversion Chart
Gas or Vapor Chemical Specific Gravity Density *In the center column, find the temperature to be converted.
Formula (lbs./cu ft.) The equivalent temperature is in the left column, if converting
Acetylene C2H2 0.899 .0686 to Celsius, and in the right column, if converting to Fahrenheit.
Air - 1.00 .0763
Ammonia NH3 0.587 .0454 °C Temp °F °C Temp °F °C Temp °F °C Temp °F
Argon A 1.377 .1053 -78.9 -110 -166 1.7 35 95.0 27.2 81 177.8 182 360 680
-73.3 -100 -148 2.2 36 96.8 27.8 82 179.6 188 370 698
Benzene C6H6 2.70 .205 -67.8 -90 -130 2.8 37 98.6 28.3 83 181.4 193 380 716
Carbon Dioxide CO2 1.539 .1166 -62.2 -80 -112 3.3 38 100.4 28.9 84 183.2 199 390 734
-56.7 -70 -94 3.9 39 102.2 29.4 85 185.0 204 400 752
Chlorine CI2 2.448 .0738 -51.1 -60 -76 4.4 40 104.0 30.0 86 186.8 210 410 770
Ethane C2H6 1.038 .0799 -45.6 -50 -58 5.0 41 105.8 30.6 87 188.6 216 420 788
Ethylene C2H4 0.969 .0739 -40.0 -40 -40 5.6 42 107.6 31.1 88 190.4 221 430 806
-34.4 -30 -22 6.1 43 109.4 31.7 89 192.2 227 440 824
Helium He 0.138 .01054 -28.9 -20 -4 6.7 44 111.2 32.2 90 194.0 232 450 842
Hydrogen H2 0.0695 .00531 -23.3 -10 14 7.2 45 113.0 32.8 91 195.8 238 460 860
-17.8 0 32 7.8 46 114.8 33.3 92 197.6 243 470 878
Hydrogen Sulfide H2S 1.19 .0897 -17.2 1 33.8 8.3 47 116.6 33.9 93 199.4 249 480 896
Methane CH4 0.555 .0424 -16.7 2 35.6 8.9 48 118.4 34.4 94 201.2 254 490 914
-16.1 3 37.4 9.4 49 120.2 35.0 95 203.0 260 500 932
Methyl Chloride CH3CI 1.785 .1356 -15.6 4 39.2 10.0 50 122.0 35.6 96 204.8 266 510 950
Nitrogen N2 0.967 .0738 -15.0 5 41.0 10.6 51 123.8 36.1 97 206.6 271 520 968
Oxygen O2 1.105 .0843 -14.4 6 42.8 11.1 52 125.6 36.7 98 208.4 277 530 986
-13.9 7 44.6 11.7 53 127.4 37.2 99 210.2 282 540 1004
Propane C3H8 1.55 .1180 -13.3 8 46.4 12.2 54 129.2 37.8 100 212.0 288 550 1022
Sulfer Oxide SO2 2.26 .1720 -12.8 9 48.2 12.8 55 131.0 43 110 230 293 560 1040
-12.2 10 50.0 13.3 56 132.8 49 120 248 299 570 1058
Water Vapor H2O 0.622 .0373 -11.7 11 51.8 13.9 57 134.6 54 130 266 304 580 1076
-11.1 12 53.6 14.4 58 136.4 60 140 284 310 590 1094
Explosive Atmosphere Classification -10.6 13 55.4 15.0 59 138.2 66 150 302 316 600 1112
-10.0 14 57.2 15.6 60 140.0 71 160 320 321 610 1130
-9.4 15 59.0 16.1 61 141.8 77 170 338 327 620 1148
North American European -8.9 16 60.8 16.7 62 143.6 82 180 356 332 630 1166
-8.3 17 62.6 17.2 63 145.4 88 190 374 338 640 1184
Class I Zone 1 -7.8 18 64.4 17.8 64 147.2 93 200 392 343 650 1202
-7.2 19 66.2 18.3 65 149.0 99 210 410 349 660 1220
Group A Group II C Acetylene -6.7 20 68.0 18.9 66 150.8 100 212 413 354 670 1238
Group B Group II C Hydrogen or equivalent hazard -6.1 21 69.8 19.4 67 152.6 104 220 428 360 680 1256
Group C Group II B Ethyle ether vapors, ethylene or -5.6 22 71.6 20.0 68 154.4 110 230 446 366 690 1274
-5.0 23 73.4 20.6 69 156.2 116 240 464 371 700 1292
cyclopropane -4.4 24 75.2 21.1 70 158.0 121 250 482 377 710 1310
Group D Group II A Gasoline, hexane, naptha, benzene, -3.9 25 77.0 21.7 71 159.8 127 260 500 382 720 1328
butane, alcohol, acetone, benzol, -3.3 26 78.8 22.2 72 161.6 132 270 518 388 730 1346
lacquer vapors or natural gas -2.8 27 80.6 22.8 73 163.4 138 280 536 393 740 1364
-2.2 28 82.4 23.3 74 165.2 143 290 554 399 750 1382
-1.7 29 84.2 23.9 75 167.0 149 300 572 404 760 1400
-1.1 30 86.0 24.4 76 168.8 154 310 590 410 770 1418
Class II -0.6 31 87.8 25.0 77 170.6 160 320 608 416 780 1436
Group E — Metal dust 0 32 89.6 25.6 78 172.4 166 330 626 421 790 1454
0.6 33 91.4 26.1 79 174.2 171 340 644 427 800 1472
Group F — Carbon black, coal or coke dust 1.1 34 93.2 26.7 80 176.0 177 350 662 432 810 1490
Group G — Flour, starch or grain
°F = 9/5C + 32 ABSOLUTE RANKIN (R) R = °F + 460
°C = 5/9 (F - 32) ABSOLUTE KELVIN (K) K = °C + 273
NEMA Classifications
NEMA Type 1 – General Purpose – Indoor Type 6 – Submersible, Watertight, Dusttight and
Type 2 – Dripproof – Indoor Sleet Resistant – Indoor and Outdoor
Type 3 – Dusttight, Raintight and Sleet (Ice) Type 7 – Class I, Group A, B, C or D Hazardous
Resistant – Outdoor Locations; Air Break Equipment – Indoor
3R – Rainproof and Sleet (Ice) Resistant Type 8 – Class I, Group A, B, C or D Hazardous
– Outdoor Locations; Oil-immersed Equipment – Indoor
3S – Dusttight, Raintight and Sleet (Ice) Type 9 – Class II, Group E, F or G Hazardous
Proof – Outdoor Locations; Air-break Equipment – Indoor
Type 4 – W atertight and Dusttight – Indoor Type 10 – Bureau of Mines
4X – W atertight, Dusttight and Corrosion Type 11 – Corrosion Resistant and Dripproof;
Resistant – Outdoor Oil-immersed – Indoor
Type 5 – Superseded by Type 12 for Control Type 12 – Industrial Use, Dusttight and Driptight
Apparatus – Indoor
Type 13 – Oiltight and Dusttight – Indoor
Ref: NEMA Standards Publication, Pub. No. 1CS–1970
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I4
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
In the following formulae these symbols are used: “Standard Air” – Air at 68°F (absolute temperature 528°) and
29.92” Hg. (barometric pressure at sea level). The density of
P – Pressure in pounds per square inch (PSI) or inches of such air is 0.075 lbs./cu. ft. and the specific volume is 13.29 cu.
mercury column (inches Hg) ft./lb. The specific gravity is 1.0.
CFM – Volume in cubic feet per minute
RPM – Speed in revolutions per minute The outlet pressure of a blower depends on the condition of
D – Density in pounds per cubic foot (lbs./cu. ft.) the air or gas at the inlet. The inlet condition is influenced by:
H – Height of air or gas column (ft.) a – Specific gravity (The ratio of density of the gas to density of
SG – Specific Gravity (ratio of density of gas to the density standard air)
of air) b – Altitude (location of blower)
c – Temperature of inlet air
Basic Fan Laws Chart
VA R I A B L E V O L U ME P R E S S UR E H O R S E P OW E R
WHEN SPEED CHANGES Varies DIRECT with Speed Ratio Varies with SQUARE of Speed Ratio Varies with CUBE of Speed Ratio
CFM 2 = CFM 1
RPM 2
RPM 1
( ) P2 = P 1
RPM 2 2
RPM 1
( ) HP 2 = HP 1 (
RPM 2 3
RPM 1
)
WHEN DENSITY CHANGES Does Not Change Varies DIRECT with Density Ratio Varies DIRECT with Density Ratio
P2 = P 1 D2
D1
( ) HP 2 = HP 1 D2
D1
( )
Volume
The Volume changes in direct ratio to the speed. V 1 = Original Volume (1000 CFM)
Example – A blower is operating at 3500 RPM and delivering V 2 = New Volume
1000 cfm. If the speed is reduced to 3000 RPM, what is the new RPM 1 = Original Speed (3500 RPM)
RPM 2 = New Speed (3000 RPM)
volume?
V2 = V 1 ( RPM
RPM
) 2
1
1
= 1000 x ( 3500
3000
) 1
= 1000 x .857 = 857 CFM
Pressure
Pressure (barometric) varies in direct proportion to Let: V 1 = Volume of standard air (1000 CFM)
altitude. V 2 = Volume of thinner air
Example – A blower is to operate at an elevation of 6000 feet Hg 1 = Barometric pressure sea level (29.92)
and is to deliver 3 PSI pressure. What pressure (standard air) Hg 2 = Barometric pressure 6000’ (23.98)
blower is required?
Hg 1 29.92
29.92 V2 = V 1 x = 1000 x = 1248 CFM
Pressure = 3 x = 3.75 or 3 3/4 lb. Hg 2 23.98
23.98
If it is desired to determine what pressure a 3 lb. (standard air) The pressure changes as the square of the speed ratio.
blower will deliver at 6000 feet –
Example – A blower is operating at a speed of 3500 RPM and
23.98 delivering air at 5.0 pounds pressure. If the speed is reduced to
Pressure = 3 x = 2.4 or about 2 1/2 lb. 3000 RPM, what is the new pressure?
29.92
When a blower is to operate at a high altitude it is frequently P 1 = Original Pressure (5 lbs.)
specified that the blower be capable of handling a given vol- P 2 = New Pressure
ume of “standard air”. It is then necessary to determine the RPM 1 = Original Speed (3500 RPM)
equivalent volume of air at the higher altitude. RPM 2 = New Speed (3000 RPM)
Example – A blower is to operate 6000 feet altitude and is to
handle 1000 CFM of standard air. What is the CFM of air the
blower must handle at 6000 feet altitude?
P2 = P 1 ( RPM
RPM
) 1
2
2
= 5x ( 3500
3000
) 2
= 5 x .735 = 3.68 pounds
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I5
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
Pressure (Cont’d)
The Air Density varies in inverse proportion to the Pressure varies in direct proportion to the density.
absolute temperature. Example – A 3 lb. (standard air) blower is to be used to handle
Example – A blower is to handle 200°F air at 3 PSI pressure. gas having a specific gravity of 0.5. What pressure does the
What pressure (standard air) blower is required? blower create when handling the gas?
Let: P 1 = Pressure hot air (3 PSI) Let: Pa = Air pressure (3 lb.)
P 2 = Pressure standard air Pg = Gas pressure
AT 1 = Absolute temperature hot air (200+460=660°F) SG = Specific gravity of gas (0.5)
AT 2 = Absolute temperature standard air (68+460=528°F)
Pg = Pa x SG = 3 x .5 = 1.5 lb.
AT 1
P2 = P 1 x = 3 x 660 = 3.75 or 3 3/4 lb.
AT 2 528
If we are required to handle a gas having a specific gravity of 0.5
at 1.5 lb. pressure, we can determine the standard air pressure
A blower is capable of delivering 3 PSI pressure with standard blower as follows:
air. What pressure will it develop handling 200°F inlet air?
AT 2 Pg 1.5
P1 = P 2 x = 3 x 528 = 2.4 or about 2 1/2 lb. Let: Pa = = = 3 lb.
AT 1 660 SG .5
Horsepower
The horsepower changes as the cube of the speed Horsepower vs. Specific Gravity & Ratio of density.
ratio. The horsepower varies in direct proportion to the specific gravity
Example – A blower is operating at a speed of 3500 RPM and (ratio of density of gas to density of air).
requiring 50 horsepower. If the speed is reduced to 3000 RPM, Example – A standard air blower requires a 10 HP motor. What
what is the new required horsepower? horsepower is required when this blower is to handle a gas
whose specific gravity is 0.5?
HP 1 = Original Horsepower (50)
HP 2 = New Horsepower HP = 10 x 0.5 = 5 horsepower
RPM 1 = Original Speed (3500 RPM)
RPM 2 = New Speed (3000 RPM) It is possible that several of the above modifications may be
required on one installation. Therefore, it may be necessary to
HP 2 = HP 1 x ( RPM
RPM
) = 50 x ( 3500
2
1
3
) 3
3000 = 50 x .630 = 31.5 horsepower use various combinations of these formulae.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I6
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
Orifice Flow
( )
V 2 100
V = CK √ P Q = AV VP =
K
Where:
80
V = V elocity in feet per minute (fpm)
C = Orifice Coefficient
K = Constant = 14,786 when P is expressed
Inches of Water
Pressure Drop
60
in In. Hg
21,094 when P is expressed
in PSIG
4,005 when P is expressed 40
in In. of Water
(Above constants are based on an air density
of 0.075 lbs/ft 3) 20
P = Pressure differential across the orifice
Q = Flow rate in cubic feet per minute (CFM)
A = T otal orifice area expressed in square feet 0 100 200 300 400 500
VP = Velocity pressure (units are those of pressure)
Flow Rate SCFM
200
Coefficient C for Orifices Under
Vacuum or Pressure Flow 180
160
140
Inches of Water
Pressure Drop
120
100
c-.98 c-.92 c-.82 c-.80 80
60
40
20
135
Area of Orifices
Orifice Diameter in Inches 120
Diameter 105
Inches of Water
Pressure Drop
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I7
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
To calculate friction loss in fittings use chart below. This chart will yield equivalent
lengths (in feet) of tubing. Use this length with graph above to find friction loss in
inches of water column.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I8
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
Noise Facts
• OSHA (Occupational Safety & Health Administration) regulates and monitors in-plant noise.
• Allowable noise is a function of dBA level at certain distance over an exposure time.
• OSHA regulations state 90 dBA for an 8 hour work period using slow responic setting on meter.
• Adding a second noise producer of equal dBA will add 3 dBA to the first dBA reading.
• Sound pressure level (SPL) decreases with distance (d)
(SPL) 2 = (SPL) 1 - 20LOG ( d1
d2
)
Therefore, each doubling of distance results in 6 dBA reduction.
10 12
120 Ft.
watts per sq. cm.)
Noisy Street
Police Whistle at 15 Ft. Auto at 60
N O I S E
MPH
NOISY
Relative Intensities (Intensity Above Threshold = 10
108 80
Very Noisy Restaurant. Auto at 40
MPH Average Stenographic Room
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
1258 Customer Service Fax: +1 215.256.1338
I9
www.ametekdfs.com ____
Application Engineering Basics
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
www.ametekdfs.com ____
Application Engineering Basics
This chart explains the nomenclature behind the catalogued blower model names. This tool can be used to explain
to customers what the letters and numbers mean, and will also allow you to become familiar with our model names.
This information should not affect the way orders are placed; please continue to use the model names shown in
the catalog and price pages. Any special request should be noted on the order.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I 11
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I 12
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
Application Engineering Basics
To obtain Application Engineering assistance or a quotation for your specific need, please photocopy this
form, fill out as much as possible, and fax it back to Rotron. We look forward to working with you.
SCFM ° (F / C)
FLOW INLET TEMPERATURE
PSI (A / G) ° (F / C)
INLET PRESSURE AREA AMBIENT TEMPERATURE
PSI (A / G) (Ft / M)
OUTLET PRESSURE SITE ALTITUDE
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763
1258 Customer Service Fax: +1 215.256.1338
I 13
www.ametekdfs.com ____
Application Engineering Basics
Warranty Statement
1. AMETEK ROTRON DR, EN, and HiE regenerative direct drive AMETEK ROTRON will not knowingly specify, design or build any
blowers are guaranteed for one full year from the date of regenerative blower for installation in a hazardous, explosive
installation (limited to 18 months from the date of shipment.) to location without proper NEMA motor enclosure. AMETEK
the original purchaser only. Should blower fail, we will evaluate ROTRON does not recognize sealed blowers as a substitue for
the failure. If failure is determined to be workmanship or explosion-proof motors. Sealed units with standard TEFC
material defect related, motors should never be utilized where local, state, and/or
federal codes specify the use of explosion-proof equipment.
2. Standard Products - AMETEK ROTRON moisture separators,
remote drives, packaged units, CP blowers, Nasty GasTM models AMETEK ROTRON has a complete line of regenerative blowers
and special built (EO) products are guaranteed for one full year with explosion-proof motors, Division 1 & 2, Class I, Group D;
from the date of shipment for workmanship and material defect Class II, Groups F & G requirements are met with these standard
to the original purchaser only. Should the blower fail, we will explosion-proof blowers.
evaluate the failure. If failure is determined to be workmanship
or material defect related, we will at our option repair or replace AMETEK ROTRON will not knowingly specify, design or build any
the blower. regenerative blower for installation in a hazardous, corrosive
environment without the proper surface treatment and sealing
3. Parts Policy - AMETEK ROTRON spare parts and accessories options.
are guaranteed for three months from the date of shipment for
workmanship and material defect to the original purchaser only. AMETEK ROTRON has a complete line of Chemical Processing
If failure is determined to be workmanship or material defect and Nasty GasTM regenerative blowers with Chem-ToughTM,
related we will at our option repair or replace the part. stainless steel parts, and seals.
4. Non-Standard Products - Orders for specially-built products AMETEK ROTRON offers general application guidance, however,
will be concidered as non-cancellable. Any requested changed suitability of the particular blower selection is ultimately the
by customer after order acceptance will result in additional responsibility of the purchaser, not the manufacturer of the
charges. blower.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled
laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application.
AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product
designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department.
AMETEK DYNAMIC FLUID SOLUTIONS
75 North Street, Saugerties, NY 12477
USA: +1 215-256-6601 - Europe: +49 7703 930909 - Asia: +86 21 5763 1258 I 14
Customer Service Fax: +1 215.256.1338
www.ametekdfs.com ____
AMETEK, Inc.
AMETEK is a leading global manufacturer of electronic instruments and electromechanical devices with
annualized sales of more than $2.5 billion. AMETEK has nearly 11,000 colleagues working at more than 80
manufacturing facilities and more than 60 sales and service centers in the United States and over 30 other
countries around the world.
AMETEK supports its customers globally from its manufacturing facilities in Minnesota, New York, North
Carolina, Ohio, Pennsylvania, Italy and China. Our brushless DC motors, blowers, controllers, pumps, and fans are
ideally suited for a wide range of applications, including medical instruments, robotics, pumps, compressors, offi ce
equipment, fans, machine tools, tape drives, or any other precise rotary motion/air delivery applications.
Technical & Industrial Products’ product line of regenerative blowers for pressure and vacuum applications
services the process, industrial, environmental, waste, and wastewater industrial industry. Typical applications
areas include solution agitation and aeration, pneumatic conveying, part hold-down and pick up, part blow off, gas
and fume extraction, and process gas handling.
AMETEK Technical & Industrial Products supplies the solution for unique performance, mounting,
environmental and agency requirements.