0 оценок0% нашли этот документ полезным (0 голосов)
445 просмотров2 страницы
Detects the presence of the radio link by detecting SACCH frames every 480 ms. Used for re-transmission on the data link. Used to limit the amount of time a user has to answer a call.
Detects the presence of the radio link by detecting SACCH frames every 480 ms. Used for re-transmission on the data link. Used to limit the amount of time a user has to answer a call.
Авторское право:
Attribution Non-Commercial (BY-NC)
Доступные форматы
Скачайте в формате DOCX, PDF, TXT или читайте онлайн в Scribd
Detects the presence of the radio link by detecting SACCH frames every 480 ms. Used for re-transmission on the data link. Used to limit the amount of time a user has to answer a call.
Авторское право:
Attribution Non-Commercial (BY-NC)
Доступные форматы
Скачайте в формате DOCX, PDF, TXT или читайте онлайн в Scribd
4 SACCH multiframes. That is T100 RADIO- Detects the presence of the radio link by detecting SACCH 1.92 seconds if the LINK-TIMEOUTÊ frames every 480 ms.Ê SACCH is completely absent.Ê T200 Data link Used for re-transmission on the data link. The value varies 155 ms for FACCHÊ timerÊ depending on the message type.Ê T301 Alerting Timer used to limit the amount of time a user has to answer a 20 secondsÊ (ringing) timerÊ call.Ê T303 Mobility Time the network waits after sending a CM SERVICE Management REQUEST until receiving a response. This occurs before 10 secondsÊ connection timerÊ initiating call clearing procedures towards the MS.Ê T305 Release Time the network waits after transmitting a DISCONNECT 10 secondsÊ timerÊ message until receiving a RELEASE message. Ê T306 In-band Time the network waits after transmitting a DISCONNECT tones release message while in-band tones/announcements are provided, 10 secondsÊ timerÊ until receiving a RELEASE message.Ê Time the network waits after sending a RELEASE message T308 Release until receiving a RELEASE COMPLETE message. This occurs 10 secondsÊ timerÊ before re-transmitting the RELEASE or releasing the Mobility Management connection.Ê Time the network waits after receiving a CALL CONFIRMED T310 Call message until receiving a ALERTING, CONNECT, or 10 secondsÊ proceeding timerÊ DISCONNECT message before initiating clearing procedures towards the MS.Ê Time the network waits after transmitting a CONNECT T313 Connect message until receiving the CONNECT ACKNOWLEDGE 10 secondsÊ acknowledge timerÊ message before performing clearing procedures with the MS.Ê Time the network waits after sending a MODIFY message T323 Modify during call mode changes, until receiving a MODIFY 10 secondsÊ complete timerÊ COMPLETE or MODIFY REJECT message before initiating call clearing procedures.Ê Time the network waits after sending the IMMEDIATE T3101 Immediate ASSIGNMENT or IMMEDIATE ASSIGNMENT EXTENDED 1 secondÊ assignment timerÊ message until the main signalling link is established before releasing the newly allocated channels.Ê Time the network waits after transmitting a HANDOVER COMMAND message until receiving HANDOVER COMPLETE or HANDOVER FAILURE or the MS re-establishes the call T3103 Handover before the old channels are released. If the timer expires and 2 secondsÊ timerÊ the network has not received a correctly decoded L2 (format A or B) or TCH frame, then the newly allocated channels are released.Ê Time the network waits after sending the PHYSICAL T3105 Physical INFORMATION message until receiving a correctly decoded L2 information 50 msÊ (format A or B) or TCH frame. This occur before re-transmitting repetition timerÊ the PHYSICAL INFORMATION message or releasing the newly Timer NameÊ 9escriptionÊ ValueÊ allocated channels.Ê Time the network waits after transmitting an ASSIGNMENT T3107 Channel COMMAND message until receiving the ASSESSMENT 3 secondsÊ assignment timerÊ FAILURE message or the MS re-establishes the call before releasing the old and the new channels.Ê T3109 Signaling Time the network waits after sending the CHANNEL RELEASE disconnection 5 secondsÊ message before disconnecting the signalling link.Ê timerÊ T3111 Channel deactivation after Time the network waits after disconnecting the signalling link 500 msÊ disconnection before deactivating the channel.Ê timerÊ Time the network waits after transmitting the PAGING REQUEST message until receiving the PAGING RESPONSE T3113 Paging message. This occurs before re-transmitting the PAGING 5 secondsÊ timerÊ REQUEST (if the maximum number of re-transmissions have not been exceeded).Ê The location update timer is set to zero, periodic location T3212 Location update by the MS are disabled. If the MS camps to the BCH zero = infinite timeÊ update timerÊ and decodes a new MCC or MNC from the one it last camped on, it should perform a location update.Ê Time the network waits after sending the TMSI T3250 TMSI REALLOCATION COMMAND until receiving TMSI 5 secondsÊ reallocation timerÊ REALLOCATION COMPLETE. This occurs before aborting the procedure and releasing the Radio Resource connection.Ê Time the network waits after an AUTHENTICATION REQUEST T3260 until receiving AUTHENTICATION RESPONSE. This occurs Authentication 5 secondsÊ before aborting the procedure and releasing the Radio response timer Ê Resource connection.Ê Ê