Академический Документы
Профессиональный Документы
Культура Документы
Commercial’s new P20 gear pumps and motors offer big performance
in a small package for hoist and wrecker body trucks. A P20 with 1/2"
gears measures just under 6" from mounting flange to port end and
weighs less than 25 lbs.
The cast iron P20 produces up to 2.96 cir at 3000 psi; output of up to
3.94 cir is available at 2500 psi. Maximum speed is 2400 rpm. Both
pump motor units are bi-rotational. Request Catalog H-109.
P20
Ideal for dump body and trailer operation, these units are rated at
2500 psi, 2400 rpm. C101’s are available in two popular sizes which
produce 38 or 48 gpm at 1800 rpm. An integral relief valve protects
the cylinder and the pump in 2-line and 3-line hook-ups. Can be
operated by cable or remote air shift. Single drive shaft models for
direct mounting are designated C102.
C101 Pump/Valve
1
VA/VG 20,35 and VG80 Directional Control Valves
10 to 120 gpm • Pressure to 3500 psi
You can combine series, parallel or tandem work sections in one bank. Mid-
bank inlets add versatility, reduce internal pressure drop and offer two-speed
control. VA20 models are rated to 40 gpm - VA35 models to 70 gpm, both at
2500 psi.
These same designs are also made of compacted graphite and designated
VG20 and VG35. A larger model, the VG80 (120 gpm) rounds out this line of
valves which are rated for 3500 psi.
VG80 Valve Bank with All models are available with manual operation or a wide selection of
Hydraulic Remote Operators pneumatic, hydraulic and electro-hydraulic operators and the controllers to
operate them.
4
Series “A”
JIC/NFPA interchangeable. Air cylinder. 250 PSI air
service.
Series “L”
JIC/NFPA interchangeable. Light duty hydraulic
cylinder. 1,000 PSI hydraulic service.
Series “H”
JIC/NFPA interchangeable. Heavy duty hydraulic
cylinder. 3,000 PSI hydraulic service.
Series “ESP”
Electronic stroke position. Heavy duty hydraulic
A&L Series cylinder. 3,000 PSI hydraulic service.
Series “HE”
Our standard “H” Series cylinder with ESP
capability. Dimensionally identical to NFPA tie-rod
hydraulic non-feedback cylinders. Remote
electronics available.
Series “W”
Welded hydraulic cylinder. 3,000 PSI hydraulic
service.
Series “MM”
Mill & mine heavy duty air cylinder. 250 PSI air
service.
Series “VA”
Valve actuator. Light duty air cylinder. 150 PSI air
service.
Series “SS”
Stainless steel round cylinder. Small bore air
Atlas Series SS cylinder. 250 PSI air service.
Series “2LA”
NFPA interchangeable. Light duty air cylinder. 150
PSI air service.
Accumulators
Piston and bladder-type accumulators. Up to 5,000
PSI hydraulic service.
H Series Atlas Custom Cylinders
Up to 48" bore. As long as 40' stroke. As high as
10,000 PSI hydraulic service. 3,000 PSI pneumatic
service. Velocities up to 100" per second.
5
HIGH POWER HYDROSTATIC DRIVE PRODUCTS SERIES 90
Pump
Technical Data Frame Size
Dimension 042 055 075 100 130 180 250*
Displacement cm3 42 55 75 100 130 180 250
in3 2.56 3.35 4.57 6.10 7.93 10.98 15.25
Input Speed - Rated min-1 (rpm) 4200 3900 3600 3300 3100 2600 2300
Input Speed - Maximum min-1 (rpm) 4600 4250 3950 3650 3400 2850 2500
Mounting Flange - SAE – B C C C D E E
• A Complete Family of Control Systems permits You to Tailor the Operator / Machine Interface to Your
• Customer’s Requirements
• Speed Sensor
• Full Power Auxiliary Pads
• Manual Displacement Control (MDC)
• Hydraulic Displacement Control (HDC)
• Electrical Displacement Control (EDC)
• Automotive Control (“Automotic-Drive”)
• 3-Position (F-N-R) Electrical Control Option
• Maximum Pressure (7000 psi)
Motor
Technical Data Frame Size
Dimension 042 055 075 100 130
Displacement cm3 42 55 75 100 130
in3 2.56 3.35 4.57 6.10 7.93
Output Rated Max. Disp. min.-1 (rpm) 4200 3900 3600 3300 3100
Speed Min. Disp. min.-1 (rpm) – 4600 4250 – –
Maximum Max. Disp. min.-1 (rpm) 4600 4250 3950 3650 3400
Min. Disp. min.-1 (rpm) – 5100 4700 – –
Mounting Flange - SAE – – C C C D
Theoretical Torque Nm/bar .67 .88 1.19 1.59 2.07
(MV at Maximum Displacment) lbf•in/1000 psi 380 530 730 970 1260
6
Bent Axis Variable Motor Series 20 Axial 2 Piston Variable Axial Piston fixed Motors
Series 51 Pumps
Motor
SERIES 51 SPECIFICATIONS
Technical Data Frame Size
Dimension 080 110 160 250
Displacement Maximum cm3 80 110 160 250
in3 4.92 6.71 9.82 15.26
Minimum cm3 16.1 22.0 32.2 50.0
in3 0.98 1.34 1.96 3.05
Output Rated Max. Disp. min.-1 (rpm) 3100 2800 2500 2200
Speed Min. Disp. min.-1 (rpm) 5000 4500 4000 3400
Maximum Max. Disp. min.-1 (rpm) 4000 3600 3200 2700
Min. Disp. min.-1 (rpm) 6250 5600 5000 4250
Mounting Flange - SAE _ C D D E
Theoretical Torque Nm/bar 1.28 1.75 2.56 3.98
(MV at Maximum Displacment) lbf•in/1000 psi 784 1067 1563 2428
Pump
SERIES 20 SPECIFICATIONS
Technical Data Frame Size
Dimension 24 25 26 27
Displacement cm3 119 166 227 334
in3 7.24 10.12 13.87 20.36
Input Speed - Rated min (rpm)
-1
2700 2400 2100 1900
Mounting Flange - SAE – D E E F
Motor Theoretical Torque Nm/bar 1.89 2.64 3.62 5.31
lbf•1000 psi 1152 1614 2208 3240
7
Pump
Technical Data Frame Size
Dimension 28 41
Displacement cm3 28 41
in3 1.71 2.50
Input Speed Rated min (rpm)
-1
3400 3400
Input Speed Maximum min-1 (rpm) 3900 3900
Length mm 199.5 225.5
• The Most Technically Advanced Intermediate Power Hydrostatic • Electrical Displacement Control (EDC)
Pumps in the Industry • 3-Position (F-N-R) Electrical Control Option
• Modular Design, with Standard Porting and Standard Mounting, • Speed Sensor
Provides the Optimum Product Configuration for Your
Application without Expensive Custom Components • Loop Flushing Circuit
• Full Power Auxiliary Pads • Suction and Pressure Filtration
• Non-Feedback Proportional Hydraulic Control (NFPH) • Maximum Pressures (5000 psi)
* Frame size 46 fixed motors have a rated and maximum speed of 3600 min-1 (rpm).
• Standard Porting and Standard Mounting • Manual Displacement Control (MDC)
• Integrated Tandem Pump Configurations Available • Hydraulic Displacement Control (HDC)
• 15 cc, 25 cc, and 35 cc with Direct Displacement Control • Electrical Displacement Control (EDC)
(DDC) • Series 40 Motor Loop Flushing
• 46 cc Pumps are Available • Maximum Pressures to (5000 psi)
Variable Pump Fan Drive System Model 310-0750 Transaxial Model 210-2510L Reduction
Drive
Variable Pump/Fixed Motor
Transmission
Single Loop Micro Controller MC Series Stackable Valves SNP2 Gear Pumps
8
“PV” Axial Piston - Variable Volume Pump “WorldCup” Axial Piston - Variable Volume Pump
Series 6, 10, 15, 20, 29 Series P6W, P7W, P8W
“GoldCup” Axial Piston - Variable Volume Pump “P16” Axial Piston - Variable Volume Pump
Series 6, 7, 11, 14, 24, 30 Series 16/260
9
“T6 Series” Vane Pumps with R5 “Tandem Pumps” Mobile “T6EDC”
Flange Valves Application
For Mobile application pumps. Add letter “M” to Series Identifier. (Sample: T6CM, T6DM, etc.)
*Combination with any SAE “A”, “B” or “C” mounting i.e. PV Piston Pump, Single or Double Vane Pump.
Note: T6 Mobile Vane Pumps are designed for applications requiring Low priming speeds to 400 RPM; Cold
start conditions of High viscosity to approximately 10,000 SUS and bidirectional cartridge assemblies.
10
Hybrid Pump Fixed and variable M4DC Double Motor
Hydraulic Pumps
(axial piston variable volume pump + constant flow vane pump one suction port)
11
Directional Valves 01, 02, 03, 06, 10 sizes “Modular Valves”
Modular Valves
Max Flow Max. Pressure Cracking Pressure
Series Size Model gpm l/M psi bar psi bar
SRV 01, 02 Relief 5000 345 – –
SRD 01, 02 Counter Balance 5000 345 – –
SRS 01, 02 Sequence 5000 345 – –
SRR 01, 02 Reducing 10 38 5000 345 – –
SCP 01, 02 Dual Pilot Oper. Check 20 76 5000 345 25 1.7
SCV 01, 02 Check 5000 345 43 29
SFT 01, 02 Meter In/Out Flow Regulator 5000 345 – –
12
“Proportional Directional Control Valve” “Proportional Pressure Control Valve”
Proportional Valves
Subplate/ISO 4401- Max. Flow Max. Pressure
Series Size Connection gpm I/M psi bar
Directional
4DP01 01 AB-03-4-A 8 30 5000 345
4DP02 02 05 16 60 4500 310
3DP03 03 95 360 5075 350
3DP06 06 185 700 5075 350
Pressure, Flow
SE0.3 1/4 1/2 NPTF, Manifold 1.5 5.7 5000 345
VP01 01 Sandwich Pilot Flow 5000 345
R1EP01 01 AB-03-4-A 2.6 10.0 5000 345
R4VP 03, 06, 10 Tee/Subplate 1/2, 1 1/2 NPTF 150 568 5000 345
F5C 06, 08, 10 3/4, 1 1/4 SAE Fig. 96 308 3000 207
R5P 06, 08, 10 SAE Fig. 160 600 3000 207
R5A 06, 08, 10 SAE Fig. 100 380 3000 207
13
MG Series
Provides an economical motor for light to medium duty applications such as
Grain Augers, Spreaders and Car Wash Brushes.
The MG motor comes with Industry Standard Porting ie NPT or SAE, and
optional 4 bolt, 2 bolt standard mounting, keyed, splined shaft are also
available.
MF Series
The MF Series Torqmotor™ provides reliable, efficient performance and long-
term economy in a broad range of applications, such as conveyors, irrigation
equipment, scissor lifts and walk behind mower. This hydraulic motor is ideal for
moderate torque applications where dependability is a must.
ME Series
The ME Series Torqmotor™ is the premier motor in its class, providing high
torque and maximum endurance under strenous conditions. The ME Series
Torqmotor™ is a time-proven top performer in applications such as wheel drives
for skid steer loaders, commercial mowers, airport ground support equipment
and municipal sweepers. Phase shift orbit valving, an industry first, minimizes
cross port leakage keeping volumetric efficiency high and output speeds
constant as pressure varies.
14
FILTRATION
High and Medium Pressure Filters
• Available with electrical and visual indicators. Pressures to 5000 PSI • Flows to 120 GPM
ACCESSORIES
• Flow Control Valves • Check Valves • Needle Valves • Ball Valves • Accumulators • Pressure Gauges • Bell
Housings and Couplings • Pressure Switches • Suction and Return Flanges • Filler Breathers • Manifolds • Oil Level
Gauges • Level Switches
FILTRATION
Suction and Return Line Filters
• From strainers to tank mounted suction filters • Return line filters in various styles to meet all applications
GEAR PUMPS
• Available in SAE A-B-C Sizes • Flows to 90 GPM • Pressures to 3500 PSI • Both Single and Double Modular
Pumps
15
FILTERING, CLEANING, SEPARATING, FILLING
16
CARTRIDGE VALVES
Check, Pilot-to-Open
Flow Model
18 lpm/5 gpm PC08-30
22 lpm/6 gpm PC10-30 Relief, Differential Area Poppet
30 lpm/8 gpm PC10-32 USASI/ISO:
Flow Model
45 lpm/12 gpm †PCV10
95 lpm/25 gpm †PCV12 30 lpm/8 gpm RV08-22
151 lpm/40 gpm †PCV16 114 lpm/30 gpm RV10-22
75 lpm/20 gpm *RV50-22
†In-line plumbed valves only
USASI: ISO: *50 size rated for 345 bar/5000 psi
17
We have all of your manual - Hydraulic and
Pneumatic clamping needs with our De-Sta-Co
line of clamping products.
CLAMP
18
PNEUMATIC
PRODUCTS
19
PNEUMATIC
PRODUCTS
2/2 Valves
Valve Model Numbers
Port Normally Normally Average CV
Size Closed Open N.C. NO.O.
1/4 2771B2001 2772B2001 2.3 2.3
3/8 2771B3001 2772B3001 3.8 3.3
1/2 2771B4011 2772B4011 4.0 3.5
Normally Closed 1/2 2771B4001 2772B4001 7.7 6.5
3/4 2771B5001 2772B5001 9.0 7.3
1 2771B6011 2772B6011 9.0 7.9
1 2771B6001 2772B6001 24 21
1-1/4 2771B7001 2772B7001 29 20
Normally Open
1-1/2 2771B8011 2772B8011 29 21
1-1/2 2771B8001 2772B8001 49 49
2 2771B9001 2772B9001 57 57
2-1/2 2771B9011 2772B9011 64 72
3/2 Valves
Valve Model Numbers
Port Sizes Normally Normally Average CV
In-Out Exh. Closed Open N.C. N.O.
1/4 1/2 2773B2001 2774B2001 2.8 2.5
3/8 1/2 2773B3001 2774B3001 4.0 3.0
1/2 1/2 2773B4011 2772B4011 3.8 3.0
Normally Closed 1/2 1 2773B4001 2774B4001 7.8 7.2
3/4 1 2773B5001 2774B5001 9.4 7.2
1 1 2773B6011 2774B6011 10 7.2
1 1-1/2 2773B6001 2774B6001 29 21
Normally Open 1-1/4 1-1/2 2773B7001 2774B7001 31 22
1-1/2 1-1/2 2773B8011 2774B8011 31 21
1-1/2 2-1/2 2773B8001 2774B8001 69 58
2 2-1/2 2773B9001 2774B9001 70 60
2-1/2 2-1/2 2773B9011 2774B9011 71 55
4/2 Valves
Port Sizes Valve Model
In-Out Exhaust Numbers Average CV
1/4 1/2 2776B2001 2.5
3/8 1/2 2776B3001 3.6
1/2 1/2 2776B4011 3.7
1/2 1 2776B4001 6.9
3/4 1 277B5001 8.2
1 1 2776B6011 8.9
1 1-1/2 2776B6001 23
1-1/4 1-1/2 2776B7001 24
1-1/2 1-1/2 2776B8011 25
20
PNEUMATIC
PRODUCTS
3/2 3/2
Pedal Treadle
4/2 4/2
21
“AC” Hydraulic Power Units
Specifications
Series/Description Motor Reservoir Flow Maximum
Model No. HP RPM Voltage (gallons) GPM Pressure
M401/Manual – Single Action
M401-251-05D01C 1.5 3600 110/220 2.00 1.12 2300
M404/No Valve
M404-204-05D01D 1.0 1800 110/220 2.00 0.76 2200
M404-251-03D01C 1.5 3600 110/220 1.00 1.12 2300
M404/Vertical - No Valve
M404-303-03H01D 2.0 3600 575 5.00 1.52 2200
M404-353-03H01E 3.0 3600 575 5.00 2.00 2500
M406/D01 - Sub-Plate for One
M406/D01 - SWH-G02C6A120 (Northman)
M046-251-03D01C 1.5 3600 110/220 1.00 1.12 2300
M406/D01 - Sub-Plate for One
M406/D01 - SWH-G02C6A120 (Northman)
M046-301-03H01D 2.0 3600 110/220 5.00 1.52 2200
M410/Manual - 4 Way - 3 Positions
M410-204-03D01D 1.0 1800 110/220 1.00 0.76 2200
M419/Single Action/Solenoid
M419-251-05D01F 1.5 3600 110/220 2.00 1.10 1500
•
More Models Available.
22
“DC” Hydraulic Power Units
Specifications
Series/Description Reservoir Flow
Model No. (gallons) (GPM) Voltage
M301/Manual – Single Action
M301-016-03B01E 0.50 1.00 12
M301-016-03D01E 1.00 1.00 12
M301-009-03D01E 1.00 1.00 24
M301-016-03G01E 3.00 1.00 12
M303/Single Action - ‘Remote Control’
M303-016-03B01E 0.50 1.00 12
M303-016-03D01E 1.00 1.00 12
M303-018-03G01G 3.00 1.50 12
M303-018-03G01E 3.00 1.00 12
M304/No Valve
M304-016-03D01E 1.00 1.00 12
M308/Two 4-Way Manual Valve
M308-016-01E01E 0.50 1.00 12
M310/4-Way Manual Valve
M310-016-03D01E 1.00 1.00 12
M313/Single Action - Longitudinal Handle
M313-018-03G01G 3.00 1.5 12
M500/Single and Double Action - Manual Valve
M500-016-03B03E 0.33 1.00 12
M616/Sub-Plate for One
M616/SHW-G02C6D12 Valve (Northman)
M616-018-07C01E 0.50 1.00 12
M629/Sub-Plate for Two
M616/SHW-G023C6D12 Valve (Northman)
M629-016-01C01E 1.00 1.00 12
M642/Double Action - ‘Remote Control’
M642-016-01C01E 1.00 1.00 12
M683/Solenoid - Single and Double
M616/Action - ‘Remote Control’
M683-016-06C01F 0.33 1.10 12
•
Other Models Available.
23
K SERIES (BULLETIN 3.00)
Compact, high performance Shell and Tube Heat Exchangers. Unique extended surface
design reduces overall size and water flow requirements. Rugged construction allows
for operating pressures to 500 psi. Optional SAE straight thread shell ports available.
24
INVENTORY
Midwest Hydraulics understands that in today’s tough
economic climate; equipment down-time means lost
income. Equipment waiting for parts to be “flown in
from the factory” is not generating income for our
customers. Midwest Hydraulics has made the
commitment to stock the parts to get our customers
back to work.
SERVICES
➤ ESTIMATES
To assist you in your decision whether to repair a component or to replace it. Midwest offers FREE estimates
on all hydraulic components brought into our shop. You know what your cost will be up front!
➤ REPAIRS
Midwest Hydraulics has complete hydraulic component repair facilities for all brands of PUMPS, MOTORS,
CONTROL VALVES and CYLINDERS.
➤ COMPONENT INTERCHANGE
It can be a difficult and lengthy procedure to obtain O.E.M. replacement parts, especially for older equipment.
Midwest’s trained staff can assist you in crossing the component over to one of the major lines we represent.
This cross-over can often be accomplished “off the shelf”.
➤ TROUBLESHOOTING
Hydraulic and pneumatic circuit problems can be difficult to trace and repair. Midwest’s technicians can
troubleshoot your system on-site and often offer some possible solutions to your problem over the telephone.
25
WINNIPEG THUNDER BAY
WINNIPEG
THUNDER BAY
TEST BENCH
All repaired components are fully tested on one of our test benches to ensure that they
will perform to the required specifications. We also perform on-site pressure and flow
testing with our new state of the art electronic testing kit, that can be downloaded to a PC.
CUSTOM DESIGN
Midwest Hydraulics’ staff can assist you in the design of a power & motion package for
new installations or for modifications to existing hydraulic and pneumatic systems. Once
a system is designed, Midwest Hydraulics can assemble and supply a complete cost-
effective package.
HYDRAULIC CYLINDER
DISASSEMBLY TABLE
FOR CYLINDER REPAIRING
ACTUAL MOTOR RPM = THEO RPM x VOL. EFF. TORQUE = PSI x DISP (IN3)
(IN LBS.) 6.28
28
NOTES
NOTES
NOTES
MIDWEST HYDRAULICS INC.
HYDRAULIC & PNEUMATIC SALES & SERVICE
Midwest Hydraulics is a privately owned and operated
Manitoba company which has earned its position as the
leading supplier of FLUID POWER products and service
throughout Manitoba and Northwestern Ontario.
Since its formation in 1975, Midwest Hydraulics’ customer
base has grown to include Mining, Logging, Pulp & Paper,
Agriculture, Manufacturing and Transportation.
With its ever increasing customer base, Midwest
Hydraulics still retains the small company image and
personal level of service that was responsible for its past
success; service that their customers have come to
expect and rely upon.