Академический Документы
Профессиональный Документы
Культура Документы
Chassis : KS3A
Model: CI593CN8XXEU CX683CN8XXEC
CW6844N8XXEF CZ6844N8XXEC
CZ6844N8XXEH
2. Reference Information
3. Specifications
5. Troubleshooting
8. Block Diagrams
9. Wiring Diagram
1. Usually, a color TV-VCR needs only slight 5. Avoid overload. Excessive signal from a
touch-up adjustment upon installation. Check sweep generator might overload the front-end
the basic characteristics such as height, of the TV. When inserting signal markers, do
horizontal and vertical sync and focus. not allow the marker generator to distort test
results.
2. Observe the picture for good black and white
details. There should be objectionable color 6. Connect the TV only to an AC power source
shading; if color shading is present, with voltage and frequency as specified on the
demagnetize, perform purity and convergence backcover nameplate.
adjustments described below.
7. Do not attempt to connect or disconnect any
3. Use the specified test equipment or its wires while the TV is turned on. Make sure
equivalent. that the power cord is disconnected before
replacing any parts.
4. Correct impedance matching is essential.
8. To protect against shock hazard, use an
isolation transformer.
SCREEN
3. Select “G2-Adjust”.
IBRM = 245
WDRV = 55
CDL = 255
COL = 200
5. Turn the SCREEN VR until “MRCR G B” and “MRWDG” are green and those value are about 100.
(The incorrect SCREEN Voltage may result that “MRCR G B” and “MRWDG” should be red)
8. Use the Channel Up/Down (▲/▼) buttons to move the cursor on the adjustment modes.
1. To enter the “Service Mode”, Press the remote-control keys in this sequence :
2. After the Service Mode is entered, the initial screen is as shown in the figure below.
3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters.
Note :
2
- When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values
should be controlled.
- After the Service adjustment is completed, Do not select “Reset” in the service mode menu.
(After above procedure is done, power is on initially and the “Plug and Play” will be operated.)
Fixed Value
1 V Shift 6 V Amp
2 V Slope 7 V SC
3 H EW 8 H Trapizium
4 H Parabola 9 H Symmetry
5 H Corner 10 H Shift
Fixed Value
1.8mA
1.6mA
MAX
BCL GAIN
BCL THESHOLD
WDRGB
50 IRE
0 Li
0 100 200 300 400 500 600 700 800 900 1023
7 X-Ray Off
8 TTX To P Off Depending on the Model
9 Tilt Control On
10 Auto FM On
11 Txt Language West Select OSD/TTX Language
Europe
4-9 MICOM
4-9-1 Pin Layout
10 GND
36 GND Analog B+
43 GND
45 I/O PX.Y In
When The Caption Function Adopted, Used.
46 I/O PX.Y Out
47 N.C.
Not Used (Programmed Gound Level)
48 N.C.
TP10
TP08 TP02
TP09 TP03
TP09
TP01
TP06
TP10 TP04
TP03
TP05
TP08
TP05
TP04
TP02
TP06
TP07
: Power Line
: Signal Line
10-2 MAIN 2
TP11
TP12
TP13
TP12
TP13
TP14
TP11
TP25
TP15
TP14
TP25
: Power Line
TP15 : Signal Line
10-3 MAIN3
TP22 TP16
TP23
TP23 TP17
TP24 TP18
TP17
TP16
TP18
TP22
TP19
TP21
TP24
TP19 TP20
TP20
TP21
: Power Line
: Signal Line
10-4 MAIN 4
TP32 TP26
TP33 TP27
TP26
TP33 TP35
TP34 TP28
TP27
TP35 TP29
TP28 TP34
TP32
TP31
TP30
TP29
TP31
TP30
: Power Line
: Signal Line
: Power Line
Si l Li
CRT SIDE AV
: Power Line
: Signal Line