Академический Документы
Профессиональный Документы
Культура Документы
Safety Instructions / Safety Parts / Service Adjustments / Service Mode General Instructions / Service Mode Cont’d / Test Signal Selection
Adjustment of Video Chroma System / CRT Diagram / Text Diagram / AV Diagram / Main Diagram / Main Diagram Cont’d
TOSHIBA 2152 DB 2
4. Rotate R350 to show the belt of vertical picture control. shown.
Service Mode Cont’d retrace. See next figure. 2. Set the TV in service mode, and get the inside
OTHER SERVICE FUNCTION 5.Adjust - / + button to increase the data W/B adjusting signal with VIDEO button. (SELF CHECK)
value of BRTC, and set it just before the 3. Select RCUT, GCUT and BCUT with CHAN- (1) 23904981
The following key entry during display of difference between the belt of vertical retrace NEL ▲, ▼ buttons, to set individual values to (2) POWER : 00
adjustment menu provides special functions. and the border of black portion of inside 32, and to set GDRV and BDRV to 20 with (3) BUS LINE : OK
pattern is visible. After that, return vertical VOLUME - / + buttons. (4) Bus CONT : OK
height and contrast. (5) BLOCK : UV V1 V2
4. Press button on the remote control and
QV01
rotate Screen VR to get one slight horizontal
line on screen.
1) Part number of microcomputer (QA01)
Note:Every pressing of button provides
2) Operation number of protecting circuit ----“00”
Horizontal line picture and Normal picture
is normal. When indication is other than “00”,
alternately.
overcurrent apts to flow, and circuit parts may
5. Press button to release horizontal line possibly be damaged.
picture, and select the two other colours 3) BUS LINE CHECK ---- “OK” is normal.
which did not light in the above step with “SDA1-GND” means that SDA line is shorted
CHANNEL ▲,▼ buttons. Then tap VOLUME to ground.
- / + buttons so that three colours slightly “SCL1-GND” means that SCL line is shorted
light in the same level. to ground.
ITEMS:
HORIZONTAL POSITION ADJUSTMENT “SCL1-SDA1” means that SDA line is shorted
To correct white balance in light area, select to SCL line.
(HPOS) GDRV and BDRV with CHANNEL ▲,▼ buttons 4) BUS CONT----“OK” is normal.
to adjust. When indication shows “Q OOO NG”, the
VERTICAL POSITION ADJUSTMENT (VPOS)
device with the number may possibly be
To correct white balance in dark area, perform damaged.
ADJUSTMENT PROCEDURE: fine adjustment of RCUT, GCUT and BCUT.
1. Set the TV in service mode, and get black or 5) BLOCK
white cross-bar signal with VIDEO button on UV : TV reception mode
Light area check (to show white)
remote hand unit. V1: VIDEO 1 input mode ( 1)
2. Select either HPOS (Horizontal picture V2 :VIDEO 2 input mode ( 2)
phase) or VPOS (Vertical picture phase) with
CHANNEL ▲, ▼ buttons, and adjust horizon- Indicated color of mode now selected: Green
TEST SIGNAL SELECTION tal or vertical picture position in the center of and Red
Using method Indicated color of other modes: White
Signals screen with VOLUME - / + buttons. Dark area check (to show black)
Every pressing of ➜ button changes the test White balance adjustment Green: Normal
H signal (Left, right, white)
patterns on screen as described below in White part. Red: The microcomputer operates to provide
H signal (Left, right, black) SELF DIAGNOSTIC FUNCTION
SERVICE MODE. White balance adjustment/check in light area. judgement of no video signal. The red color is
1) Press “9” button on Remote Control during still indicated though the signal is input, failure
Black part. Picture display of adjustment menu. The diagnosis
Signal off ➜ NTSC signals (14 patterns) White balance adjustment/check in dark area. may exist in input signal line including QV01.
will begin to check if interface among IC’s are QV01: In case of indication green --- Normal
Making. approx. 1Vp-p signal in QA01. executed properly.
➜
➜
Safety Instructions / Safety Parts / Service Adjustments / Service Mode General Instructions / Service Mode Cont’d / Test Signal Selection
Adjustment of Video Chroma System / CRT Diagram / Text Diagram / AV Diagram / Main Diagram / Main Diagram Cont’d
TOSHIBA 2152 DB 3
ADJUSTMENT OF VIDEO-CHROMA SYSTEM
(Factory Adjustment)
Item Name Setting(User control) Input signal Measurement point Adjustment procedure Adjustment standard
Slave SUB Contrast: MAX Sub-bright Screen 1. This adjustment must be done 5 ± 1.5
address 36 BRIGHT Bright: CENTER signal adjustment after [BRTC], screen VR and white balance adjustments
signal.
Slave SUB Contrast: MAX Sub-bright IC501 1. Select slave address 39 1.4V(p-p)
[COLP] PAL Color: CENTER (PAL) (B-OUT) 2. When [COLP] is selected, Y-signal is muted
bar output.
Screen VR Screen GDRV 20 Hexa-decimal 3. Determine the position of the screen VR here.
CRT Diagram
BDRV 20 Hexa-decimal 4. Adjust RCUT, GCUT and BCUT, brighten other lines
pressing -I- - button on the remote (Adjust DATA so that the line becomes almost white.)
control in service mode. 5. Press -I-- button on the remote control to escape from the
31[GCUT] G cut-off Bright : CENTER adjustment after adjustment of the above- (103cd/m3)
voltmeter.
3.Adjust DC voltage.
Slave Chroma Contrast: MAX PAL Pin 23 of 1.Select slave address F1 TRP Chroma level:
address trap f0 Bright : MIN colour bar IC501 2. Adjust chroma trap so that MIN
Safety Instructions / Safety Parts / Service Adjustments / Service Mode General Instructions / Service Mode Cont’d / Test Signal Selection
Adjustment of Video Chroma System / CRT Diagram / Text Diagram / AV Diagram / Main Diagram / Main Diagram Cont’d
TOSHIBA 2152 DB 4
AV Diagram
Safety Instructions / Safety Parts / Service Adjustments / Service Mode General Instructions / Service Mode Cont’d / Test Signal Selection
Adjustment of Video Chroma System / CRT Diagram / Text Diagram / AV Diagram / Main Diagram / Main Diagram Cont’d
TOSHIBA 2152 DB 5
Main Diagram
TOSHIBA 2152 DB 6
Main Diagram Cont’d