Вы находитесь на странице: 1из 6

The circuit uses a diac for the alternate switching of LED.

The diac is usually used in pulse generator


circuits to trigger SCR and Triac. If a low voltage passes through a diac, it simply behaves like an open
circuit and only very low current passes through it. But if the voltage increases to the breakdown threshold
of the diac, it will pass heavy current. Usually 35 volt DC is required to attain the threshold level of diac.
Unlike SCR, diac conduct in both the directions. In the circuit, a commonly available DB3 diac is used.
Diode D1 rectifies AC and generates a high volt DC. Resistor R1 safely controls the DC to operate diac and
LED.

Normally LED will be OFF. When the capacitor charges fully, diac gets the threshold voltage and fires. This
provides current to LED and it lights. Resistor R2 makes the LED current to a safer value of 30 mA. When
the diac conducts, C1 discharges and again the breakdown voltage of diac decreases and LED turns off.
Thus the charging/discharging cycles of C1 makes the LED flashing. The value of C1 determines the flash
rate. Higher values give slow flash rate and vice versa. If the threshold level of diac is not obtained using the
given value of R1, reduce it to 10K, but its wattage should be increased to 5 watts.

Caution: The circuit is directly connected to high volt AC and there is no galvanic isolation. Take utmost
care while handling the circuit. Enclose it in a shock proof case. Do not touch any points when it is
connected to Mains.

Diac controlled Flasher Circuit


Automotive Brake Lights Flasher Project

This project is a flasher circuit able to turn on and off a bulb instead of a LED. It is based on the 555 timer
IC is connected for astable multivibrator operation. It will create a flashing condition on the brake lights
while the brake is pressed.
12V LED Flasher
This circuit is designed to flash an LED at a constant rate
and could be used to give the appearance of an active alarm system
in a car.

Parts list
• C1 220uF capacitor
• LED
• IC LM3909 Flasher
• R1 3.9K 1/2 watt resistor
• R2 1.0K 1/4 watt resistor

Flasher Elektronik
Diposting oleh Nurwanto Sujarwo Jam 14:48 . 29 Januari 2010
Udah tiga hari ini flasher motor lagi ngadat.pengennya sekalian dandanin biar tambah oke. Tadinya mau di
kasih lampu sein yang pake Lampu LED (Light Emiting Diode), tapi mesti ganti flasher elektronik dulu
[flasher orisinil masih mekanik, pake relay magnet]

Muncul ide… daripada beli. Mending bikin ajah…

Browsing internet sejam-an cari rangkaia flasher elektronik yang pas. Dapet deh 1 rangkaian buat gantiin
Flasher mekanik, rangkaian elektronik murah n meriah…coz gampang dapetin komponennya di toko2
elektronik… skema lihat diatas…
Ini bahan2 nya :
- IC timer NE555 : 1 buah (jangan lupa juga soket IC 8 kaki yak??)
- Resistor : 68K Ohm, 39K Ohm n 100 ohm masing2 1 buah
- Capasitor : 10uF/ 35V (orang sering bilang Elko) 2 buah, 100uF/ 35V. 1 buah n capasitor keramik 1nF, 1
buah
- Transistor PNP tipe TIP32, 1 buah
- Diode IN4148, 1 buah
- PCB (printed circuit board) berlubang secukupnya
- Kabel secukupnya
catatan : ini cuma buat VEGA R T105SE(5ER9), kalu buat yang laen. mesti liat skema Lampu Sein nya
dulu… barangkali beda..

Вам также может понравиться