Вы находитесь на странице: 1из 2

541EE (EU) July 1999

EPICON MARINE FINISH


EPICON MARINE FINISH is an abrasion resistant, high gloss finish with excellent durability and adhesion properties.

TECHNICAL DATA
Type Recommended use Surface Preparation Epoxy/polyamide finish coat. Finish coat for EPICON MARINE system for the external hull and decks of steel ships, bridges and other steel structures. All surface contamination such as dirt, grease, oil, etc. must be removed. May also be used over a wide range of existing coatings.

Physical Data

(mix)

Colour Flash point Volume solids VOC (as supplied) Mixing ratio Thinner Application Data

: : : :

as specified 41 C 58% 470 g/l

Application Details

Film Thickness Spreading Rate (Theoretical) Preferable preceding coats Preferable subsequent coats Packing

: base : hardener = 78 : 22 ( by volume) : EPICON Thinner : Airless spray, brush, roller Add the hardener to the base whilst mixing. Stir well before use. Minimum temperature : 5 C Maximum humidity : 85%RH For airless spray: Tip No. : Graco 619, 719 Paint output pressure : 150 - 180 Kgf/cm Viscosity : 60 sec. (Ford Cup No. 4) Thinning : 0 - 5% (by volume) : Wet : 52 - 86 microns Dry : 30 - 50 microns : 19,2 m/l (at DFT 30 microns)

EPICON MARINE UNDERCOAT, UMEGUARD SERIES, other Epoxy primers, etc. --Two pack product.

Mediator Co. Ltd. - 43 Marasesti Blvd, 75114, Bucharest 4, Tel/Fax: 40.1.336.54.45 / 336.03.95 / 337.34.72

Page 1 of 2

541EE (EU) July 1999

Coating data Temperature Drying time (at DFT 50) Overcoating intervals (at DFT 50) Pot life 24 hrs 24 hrs 18 hrs 12 hrs surface dry hard dry minimum 5 C 3,5 hrs 34 hrs 20 hrs 10 C 2,5 hrs 24 hrs 14 hrs 20 C 1,5 hrs 14 hrs 8 hrs 30 C 1 hr 10 hrs 6 hrs

Health and Safety

Risk phrases Safety phrases Contains

: 10, 20/21/22, 38 : 26, 51 23, 38 : Xylene

or or or

10, 40/20/21/22, 33, 61 26, 20/21, 23, 38 Xylene, Leadchromate (depending on colour)

The Personal Protection advice for this product is listed under P.P.A. No. 3/5. Additional information can be obtained from the product Health and Safety Data Sheet which is available on request. The minimum safety precautions in dealing with this paint are: a. Observe the precautionary notices displayed on the container. b. Provide adequate ventilation. c. Avoid skin contact and inhalation of spray mist. d. If the product comes into contact with the skin, wash thoroughly with luke warm water and soap. If the eyes are contaminated, rinse with water and seek medical advice immediately. e. Since the product contains flammable materials, keep away from sparks and open flames. No smoking should be permitted in the area. Definitions Tolerances Spreading Rate Volume Solids The numerical information quoted in this Technical Data Sheet is subject to normal manufacturing tolerances. The spreading rate may vary with application conditions, the geometrical complexity of the structure, the weather conditions, etc. The volume solids figure given in this Technical Data Sheet is the percentage of dry film obtained from a given wet film thickness under specified application rate and conditions measured by the Chugoku Standard Method corresponding to ASTM method D2697. The intervals given assume preparation consistent with good painting practice. Theoretical quantity of volatile organic compounds in g/l.

Overcoating Intervals VOC Safety information

When Health, Safety or Environmental information is required a Health and Safety Data Sheet can be obtained from Chugoku Paints B.V.

Disclaimer

Data,specifications,directions and recommendations given in this data sheet represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy,completeness or appropriateness under the actual conditions of any intended use is not guaranteed and must be determined by user. The products are delivered and any technical assistance is given subject to our GENERAL CONDITIONS OF SALE,DELIVERY AND SERVICE and,unless otherwise expressly agreed in writing,manufacturer and seller assume no liability in excess of that stated therein for results obtained,injury,direct or consequential damage incurred from the use as recommended above or otherwise. Product data are subject to change without notice and automatically void two years from issue.

Mediator Co. Ltd. - 43 Marasesti Blvd, 75114, Bucharest 4, Tel/Fax: 40.1.336.54.45 / 336.03.95 / 337.34.72

Page 2 of 2

Вам также может понравиться