Академический Документы
Профессиональный Документы
Культура Документы
Version : R6.1
www.Prepking.com
www.Prepking.com
1. A company has deployed a NetApp dual controller FAS3100 series with iSCSI. Currently, there are five Windows servers and three Novell NetWare servers connected to the IP SAN. The customer wants to connect an HP-UX server to the IP SAN. Which cfmode allows all operating systems to co-exist in the IP SAN? A. single_image B. standby C. cfmode not applicable D. dual_fabric Answer: C
A Solaris 10 host with VERITAS Storage Foundation 4.1 is FCP attached to a FAS3140 high availability storage system running single image cfmode. Using the diagram shown, which ports will be considered active by VERITAS DMP using the NetApp ASL to a LUN on controller 1 mapped to host 1? A. Port 0b on controller 1 only
www.Prepking.com
B. Port 0d on controller 1 only C. Port 0b and 0d on controller 1 only D. Ports 0b and 0d on both controller 1 and controller 2 Answer: C
3. For which four operations would you use igroup throttles on a NetApp storage solution? (Choose four.) A. to assign a specific percentage of the queue resources on each physical port to the igroup B. to manage pathing to the LUNs C. to reserve a minimum percentage of queue resources for a specific igroup D. to limit the number of concurrent I/O requests an initiator can send to the storage system E. to restrict an igroup to a maximum percentage of use F. to manage space reclamation Answer: ACDE
4. Which command do you use to see the rate of change between two successive Snapshot copies in a flexible volume in Data ONTAP? A. snap diff B. snap calculate C. snap delta D. snap space Answer: C
5. Which utility on Windows 2003 and Windows 2008 can be used to collect information about firmware and driver versions for an Emulex LP1xxxx/LPe1xxx HBA? A. EMutil B. SANutil C. fcp config D. SANsurfer E. HBAnywhere Answer: E
www.Prepking.com
6. Which utility on Solaris 10 can be used to collect information about firmware and driver versions for an Emulex LP1xxxx/LPe1xxxx HBA? A. EMutil B. SANutil C. hbainfo D. SANsurfer E. HBAnywhere Answer: E
7. Which utility on Solaris 10 can be used to collect information about firmware and driver versions for a Qlogic QLAxxx/QLExxxx HBA? A. EMutil B. SANutil C. cfgadmin D. SANsurfer E. HBAnywhere Answer: D
8. An organization currently has a NetApp Fibre Channel block-based solution. With limited budget and resources, they want to create a new disaster recovery site that utilizes a NetApp solution. What would the optimal solution include? A. SnapMover and Fibre Channel at the disaster recovery site for all hosts B. SnapMirror and iSCSI at the disaster recovery site for all hosts C. Fibre Channel at both locations using ftp to replicate storage D. MetroCluster and NAS Answer: B
9. A company has a Fibre Channel environment and wants to connect a new host in a remote data center using 50/125um OM2 multi-mode fiber cable and needs to support 2 Gb speeds.
www.Prepking.com
What is the maximum distance of the cable run supported in this situation? A. 50/125um OM2 multi-mode fiber cable supports up to 500 meters at 2 Gb. B. 50/125um OM2 multi-mode fiber cable supports up to 10000 meters at 2 Gb. C. 50/125um OM2 multi-mode fiber cable supports up to 150 meters at 2 Gb. D. 50/125um OM2 multi-mode fiber cable supports up to 300 meters at 2 Gb. Answer: D
Given the information provided in the diagram, what is the appropriate FC topology? A. point-to-point B. switched fabric C. arbitrated loop D. ring Answer: B
11. Which FC SAN topology provides the best performance and scalability? A. cascade B. core-edge
www.Prepking.com
Based on the diagram shown, what is the appropriate FC switch topology? A. full mesh B. core-edge C. full cascade D. partial mesh Answer: B
Based on the diagram shown, what is the appropriate FC switch topology? A. core-edge B. full mesh C. partial mesh D. partial cascade
www.Prepking.com
Answer: C
14. A 200-GB LUN is created in an empty 500-GB volume with the volume guarantee option set to Volume. LUN reservation is enabled and the fractional reserve is set to 100. Directly after LUN creation, what is the maximum free space available in the volume? A. 200 GB B. 300 GB C. 400 GB D. 500 GB Answer: B
15. A 100-GB thinly provisioned LUN is allocated to a Windows host. 100 GB of data is written into the LUN. The current capacity utilization on the disk array as well as the host is 100%. 50 GB of data is deleted from the LUN. Space reclaimer has NOT been run. What is the current capacity utilization on the disk array was well as the host? A. 50% on the host, 100% on the disk array B. 100% on the host, 50% on the disk array C. 50% on the host, 50% on the disk array D. 100% on the host, 100% on the disk array Answer: A
16. A customer has a four-node SUN cluster configuration. Each node has two, dual-ported HBAs. What is the minimum number of igroups that need to be created to map a LUN to the cluster? A. 1 B. 2 C. 4 D. 8 Answer: A
17. Zoning by World Wide Port Name (WWPN) is deployed and a host HBA is replaced.
www.Prepking.com
Which zone change needs to be made? A. No changes are necessary. B. The zone configuration should be changed to include the port to which the HBA is connected. C. The zone configuration should be changed to include the WWPN of the new HBA; the old WWPN will be automatically dropped. D. The zone configuration should be changed to include the WWPN of the new HBA and to remove the WWPN of the old HBA. Answer: D
18. Which two privileges must the SnapDrive service account have? (Choose two.) A. backup privileges on the storage system B. backup privileges on the host C. administrator privileges on the storage system D. administrator privileges on the host Answer: CD
19. Which cfmodes does the FAS2020a support? A. dual_fabric only B. single_image C. partner D. standby Answer: B
20. What is the minimum version of Data ONTAP required to use single-image cfmode? A. 6.5.X B. 7.0.5 C. 7.1.0 D. 7.2.0 Answer: C
www.Prepking.com
21. A company has a FAS3170 system and they need twelve, 4-Gb target ports. What can they do to achieve this? A. add dual port 4-Gb target HBAs into each controller and configure onboard ports for disk access B. add quad port 4-Gb target HBAs into each controller and continue to use onboard ports for targets C. add quad port 4-Gb target HBAs into each controller and configure onboard ports for disk access D. add quad port 4-Gb initiator HBAs into each controller and configure onboard ports for target access Answer: C
You see the following error on the storage controller's console or messages file. What is the most likely cause for this error? A. portal group misconfiguration B. iSCSI CHAP misconfiguration C. iSNS misconfiguration D. IPsec misconfiguration Answer: B
23. Which native GUI switch tool is used to manage Brocade switches and directors? A. SAN Manager B. Enterprise Fabric Services C. Device Manager D. Web Tools Answer: D
24. Which command will display which Brocade switches are connected into a fabric? A. fabricshow B. switchshow C. show fabric
www.Prepking.com
100% Pass Guaranteed or Full Refund Word to Word Real Exam Questions from Real Test Buy full version of exam from this link below http://www.prepking.com/NS0-501.htm