Академический Документы
Профессиональный Документы
Культура Документы
MULTI
DESIGN
SOLUTIONS
MONO
MULTI
DESIGN
SOLUTIONS
Ballast Pan
Trinamount III of Trina Solar offers the fastest and least expensive way to mount PV arrays on flat roofs. With a series of drop-in and quarter turn connections, Trinamount III greatly accelerates the process of commercial rooftop installation. Trinamount III eliminates the need for mounting rails, requires very few parts, and simultaneously accomplishes structural and grounding connections. With far less complexity than conventional systems, Trinamount III delivers both labor and logistics savings for commercial PV projects.
TSM-PC05/PA05.10
Trina module
Trinamount system
Low parts and SKU count in comparison to conventional mounting solutions Superior aesthetic solution for residential rooftops
www.trinasolar.com
MONO
MULTI
DESIGN
SOLUTIONS
MONO
MULTI
DESIGN
SOLUTIONS
Basic Hardware
1000W/m2
Row Connector
800W/m2 600W/m2
6.00 5.00 4. 3.
00 00
400W/m2 200W/m2
41.3mm 1.63in
80.3mm 3.16in
914.4mm 36.00in
30.00
40.00
The row connector provides a point of attachment for the Front and Rear Legs and creates a rigid connection beween rows. The profile of the Row Connector accepts standard strut nuts for attaching standard strut or brackets for applications that require bracing for seismic and high wind applications.
up to 14.7% up to 240W
Ballast Pan
25
8.32in 211.3mm 3.11in 79mm
35.64in 905.2mm
Recyclable packaging
The Ballast Pan installs, by hand, over the Row Connector and receives ballast blocks to add ballast weight to the system.
Back View
A-A
in progress Front & Rear Legs TSM-230 PC05/PA05.10 230 0/+3 29.8 7.72 37.0 8.26 14.1 TSM-235 PC05/PA05.10 235 0/+3 30.1 7.81 37.1 8.31 14.4 TSM-240 PC05/PA05.10 240 0/+3 30.4 7.89 37.2 8.37 14.7
The Leg Set consists of a Front Leg and a Rear Leg which snap, by hand, into the Row Connectors. The Legs create an 11 degree array tilt angle.
5.64in 143.2mm 5.64in 143.2mm FRONT LEG 12.32in 312.9mm 12.32in 312.9mm FRONT LEG
Electrical Data @ STC Peak Power Watts-PMAX (WP) Power Output Tolerance-PMAX (%) Maximum Power Voltage-VMAX (V) Maximum Power Current-IMPP (A) Open Circuit Voltage-VOC (V) Short Circuit Current-ISC (A) Module Efficiency m (%)
TONGUE SIDE
KEY SIDE
REAR LEG
REAR LEG
Values at Standard Test Conditions STC (Air Mass AM1.5, Irradiance 1000W/m, Cell Temperature 25C)
Mechanical Data Solar cells Cells orientation Module dimension Weight Glass Frame J-Box Cables/Connector Multicrystalline 156 x 156mm (6 inches) 60 cells (6x10) 1650 x 992 x 40mm (64.95 x 39.05 x 1.57inches) 19.5kg (43.0lb) High transperancy solar glass 3.2mm (0.13inches) Anodized aluminium alloy IP 65 rated Photovoltaic Technology cable 4.0mm (0.006inches), 1000mm (39.4inches), MC4 Warranty -40~+85C 1000/600VDC 15A 5 years workmanship warranty 10 years warranty, 90% power output 25 years warranty, 80% power output
Temperature Ratings Nominal Operating Cell Temperature (NOCT) Temperature Coefficient of PMPP Temperature Coefficient of VOC Temperature Coefficient of ISC 46C (2C) - 0.45%/C - 0.35%/C 0.05%/C
Accessories
Wind Diuser
Diuser Support
Ground Bolt
Maximum Ratings Operational Temperature Maximum System Voltage Max Series Fuse Rating
Packaging Configuration Modules per box Modules per 40" container 25 pcs 650pcs
The Spoiler is installed on the back side of each row and reduces uplift forces due to wind by redirecting air over and around the array, balancing air pressures across the upper and lower sides of the array. The Spoiler Support provides additional rigidity along the upper edge of the module row and supports the ends of the Spoilers. Attaches to Groove. One Ground Bolt per every 72 modules max (see Installation Manual for instructions).
www.trinasolar.com