Академический Документы
Профессиональный Документы
Культура Документы
BXD Series
The BXD (Broadband X-Pol Dual-Band) is a slant +/-45 panel antenna operating within the 806-900 MHz & 1850-1990 MHz dualband frequency range. BXDs are a design combination of our BXA-800 and BXA-1850 slant +/-45 panels. Antennas feature fixed electrical downtilt and null fill. Optional diplexers and diplexer packages (CIJI kits) are available for use with BXD antennas.
Design and Construction of the BXD Panel: BXD antennas are manufactured with our exclusive 3T Technology, featuring single-piece, water-cut brass feedline assemblies for consistent performance; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipation to minimize plate warping and bending. Model Number Guide: BXD- 63 4 4 63 8 2 CF E-DIN
Connector Type NE is an elongated N connector E-DIN is an elongated DIN connector CF refers to a Center-Fed connector BF refers to a Bottom-Fed connector Electrical Downtilt (Side 2: 1850-1990 MHz) Number of Dipole Pairs (Side 2: 1850-1990 MHz) Horizontal Beamwidth (Side 2: 1850-1990 MHz) Electrical Downtilt (Side 1: 806-900 or 806-960 MHz) Number of Dipole Pairs (Side 1: 806-900 or 806-960 MHz) Horizontal Beamwidth (Side 1: 806-900 or 806-960 MHz)
Models Currently Available: Model Number BXD-40404080CF _ BXD-63206340CF _ BXD-63406380CF _ BXD-63606380CF _ BXD-90409080CF _ BXD-908090120CF _ Frequency Range (MHz) 806-900 MHz* 1850-1990 MHz 806-900 MHz* 1850-1990 MHz 806-900 MHz* 1850-1990 MHz 806-900 MHz* 1850-1990 MHz 806-900 MHz* 1850-1990 MHz 806-900 MHz* 1850-1990 MHz H-Plane 40 40 63 63 63 63 63 63 90 90 90 90 E-Plane 15 7 30 14 15 7 11 7 15 7 7 5 Gain 14.5 dBd 19.5 dBi 10 dBd 15.5 dbi 13 dBd 18 dBi 14.5 dBd 18 dBi 11 dBd 16.5 dBi 14 dBd 18 dBi Fixed Electrical Downtilt Options 0 0 0 0 0, 4 0, 2, 4 0 0 0, 2, 4 0, 2, 4 0 0 Length x Width x Depth (in inches) 48.0 x 36.0 x 10.0 23.8 x 16.7 x 4.9 47.4 x 16.8 x 3.5 71.1 x 16.8 x 4.2 47.2 x 16.5 x 7.5 94.7 x 16.7 x 5.9
*This model is also available up to 960 MHz. Consult your sales representative for details. When ordering replace __ with the connector type (NE or E-DIN).
Mechanical specifications
Length Width Depth
4)
BXD-40404080CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
Rated Wind Velocity (Safety factor 2.0) >221 km/hr >137 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1580 N 355.3 lbs Side 447 N 100.5 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
40
Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
150
Cellular Side
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 604 mm 424 125 165 5.6 mm mm mm kg m2 23.8 in 16.7 4.9 6.5 12.3 in in in lbs ft2
BXD-63206340CF __
When ordering replace ___ with connector type.
Radiation
-11 0 -12 0 -130 -140 -15 0 -16 0 -10 0
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30
4)
0.256 0.077 m2
-17 0 180 170 160 150 140 4 0 130 120 110 100 9 0 8 0 70 6 0 50
Rated Wind Velocity (Safety factor 2.0) >614 km/hr >381 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 363 N 81.6 lbs Side 111 N 24.9 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 180 170 160 150 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0 30 35 30 25 20 15 10 5 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 1 0 20
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
806-900 MHz* 63 30 10 dBd / 12 dBi 0 1850-1990 MHz 63 14 13.5 dBd / 15.5 dBi 0
-16 0 -17 0 180 170 160 150 140
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 4 0 130 120 110 100 9 0 8 0 70 6 0 50
PCS Side
50 <-25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 180 170 160 150 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0 30 35 30 25 20 15 10 5 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 1 0 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1204 mm 427 89 129 7.7 mm mm mm kg m2 47.4 in 16.8 3.5 5.1 17.0 in in in lbs ft2
BXD-63406380CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
4)
0.51 0.11 m2
-170 180 170 160 150 140 40 130 50 120 110 100 90 80 70 60
Rated Wind Velocity (Safety factor 2.0) >590 km/hr >367 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 731 N Side 177 N 164 lbs 40 lbs
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5-15% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1204 mm 427 89 129 7.7 mm mm mm kg m2 47.4 in 16.8 3.5 5.1 17.0 in in in lbs ft2
BXD-63406382CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
4)
0.51 0.11 m2
-170 180 170 160 150 140 40 130 50 120 110 100 90 80 70 60
Rated Wind Velocity (Safety factor 2.0) >590 km/hr >367 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 731 N Side 177 N 164 lbs 40 lbs
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5-15% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1204 mm 427 89 129 7.7 mm mm mm kg m2 47.4 in 16.8 3.5 5.1 17.0 in in in lbs ft2
BXD-63446384CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
4)
0.51 0.11 m2
-170 180 170 160 150 140 40 130 50 120 110 100 90 80 70 60
Rated Wind Velocity (Safety factor 2.0) >590 km/hr >367 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 731 N Side 177 N 164 lbs 40 lbs
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5-15% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket
4)
BXD-63606380CF __
When ordering replace ___ with connector type.
71.1 in 16.8 in 4.2 in 5.8 in 28.0 lbs 8.3 2.1 ft2 ft2
Radiation
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40
Rated Wind Velocity (Safety factor 2.0) >463 km/hr >288 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1094 N 245.9 lbs Side 334 N 75.2 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
50
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
806-900 MHz* 63 11 14.5 dBd / 16.5 dBi 0 1850-1990 MHz 63 7 16 dBd / 18 dBi 0
-160 -170 180 170 160 150 140
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5-15% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1200 mm 420 190 230 7.9 mm mm mm kg m2 47.2 in 16.5 7.5 9.1 17.5 in in in lbs ft2
BXD-90409080CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
4)
0.51 0.23 m2
-170 180 170 160 150 140 40 130 50 120 110 100 90 80 70 60
Rated Wind Velocity (Safety factor 2.0) >454 km/hr >282 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 715 N Side 350 N 161 lbs 79 lbs
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
806-900 MHz* 90 15 11 dBd / 13 dBi 0 1850-1990 MHz 90 7 14.5 dBd / 16.5 dBi 0
-160 -170 180 170 160 150 140
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1200 mm 420 190 230 7.9 mm mm mm kg m2 47.2 in 16.5 7.5 9.1 17.5 in in in lbs ft2
BXD-90429082CF __
When ordering replace ___ with connector type.
Radiation
-110 -120 -130 -140 -150 -160 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30
4)
0.51 0.23 m2
-170 180 170 160 150 140 40 130 50 120 110 100 90 80 70 60
Rated Wind Velocity (Safety factor 2.0) >454 km/hr >282 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 715 N Side 350 N 161 lbs 79 lbs
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
806-900 MHz* 90 15 11 dBd / 13 dBi 2 1850-1990 MHz 90 7 14.5 dBd / 16.5 dBi 2
-160 -170 180 170 160 150 140
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -140 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 40 130 120 110 100 90 80 70 60 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket Weight Wind Area Fore/Aft Side 1200 mm 420 190 230 7.9 mm mm mm kg m2 47.2 in 16.5 7.5 9.1 17.5 in in in lbs ft2
BXD-90449084CF __
When ordering replace ___ with connector type.
Radiation
-11 0 -12 0 -130 -140 -15 0 -16 0 -10 0
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30
4)
0.51 0.23 m2
-17 0 180 170 160 150 140 4 0 130 50 120 110 100 9 0 8 0 70 6 0
Rated Wind Velocity (Safety factor 2.0) >454 km/hr >282 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 715 N Side 350 N 161 lbs 79 lbs
Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 180 35 30 25 20 15 10 5 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
806-900 MHz* 90 15 11 dBd / 13 dBi 4 1850-1990 MHz 90 7 14.5 dBd / 16.5 dBi 4
-16 0 -17 0 180 170 160 150 140
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 4 0 130 120 110 100 9 0 8 0 70 6 0 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 180 170 160 150 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0 30 35 30 25 20 15 10 5 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 1 0 20
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Mechanical specifications
Length Width Depth Depth with z-bracket
4)
BXD-908090120CF __
When ordering replace ___ with connector type.
94.7 in 16.7 in 5.9 in 7.5 in 37.0 lbs 11.0 3.9 ft2 ft2
Radiation
-110 -120 -130 -14 0 -150 -16 0 -170 180 170 160 150 140 -100
pattern1)
-90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 40
Rated Wind Velocity (Safety factor 2.0) >294 km/hr >183 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1491 N 335.2 lbs Side 631 N 141.8 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.
50
Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 180 170 160 150 140 130 120 110 100 90 80 70 6 0 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 2 0
Electrical specifications
Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Frequency Range 1) Half Power Angle H-Plane E-Plane 1) Gain 1) Electrical Downtilt Impedance Isolation 3) Connectors
Cellular Side
Vertical
Radiation pattern1)
PCS - 1850-1990 MHz
-110 -120 -130 -14 0 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 40 130 120 110 100 90 80 70 6 0 50
PCS Side
50 -25 dB NE or EDIN 4 ports / center 1) 1.4:1 VSWR Polarization Slant +/- 45 2) Power Rating - Cellular 500 W Power-Rating - PCS 250 W 1) Null Fill 5-15% Lightning Protection Direct Ground
*Also available up to 960 MHz. Consult your sales director for more information. Patented Dipole Design: U.S. Patent No. 6,608,600 B2
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 180 170 160 150 140 130 120 110 100 90 80 70 6 0 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 2 0
Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connectors only.
Vertical
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com
Bracket Type
Standard BXD Mounting Bracket Kit for: BXD-40404080CF BXD-63206340CF BXD-63406380CF BXD-63606380CF BXD-90409080CF BXD-908090120CF
36210002
Top View
Side View
36114003
Standard BXD *Downtilt Bracket Kit for: BXD-63206340CF BXD-63406380CF BXD-63606380CF BXD-90409080CF BXD-908090120CF
36114003
RWA ANTENNA
Top View
Side View
*Both the downtilt bracket kit and the standard mounting bracket kit must be ordered for mechanical downtilt applications.
Mounting Bracket Kits are sold separately and not included in the price of antennas.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com
RWA ANTENNA