Академический Документы
Профессиональный Документы
Культура Документы
2005-2006 Infill/Maxan/StreetDeck all rights reserved. Written by Adam Stolarz and Chuck Holbrook
TOOLS NEEDED
Some may be optional, depending on your vehicle. Flat-head screwdriver Phillips-head screwdriver Electrical tape Panel tool / Retaining clip remover Wire Cutters Wire Strippers
may not match the colors on your vehicles harness, you should be sure of the wires function before connecting them together.) You can use
either crimp connectors or soldering to connect the bare wires of the harnesses together. Crimp connectors are faster and easier than soldering, but not as professional. If you do solder your connections, be sure to use heat shrink tubing around the connections as electrical tape can dry out and fall off with extended use in a harsh vehicle environment. In addition to the speaker and power connections found in all car stereo harnesses, your cars stereo harness may or may not have a wire for illumination (ILL), for the parking brake (HAND BRAKE), or for a power antenna (ANTENNA+). In such a case, you can leave the illumination wire disconnected and adjust the brightness of the Infill T3 manually by pressing and holding the Mode button on the T3 display for a second. If you dont have a power antenna wire in your stereo harness, it probably means you dont have a power antenna and you can leave the wire disconnected as it will not be needed. You will need to find and connect the HAND BRAKE wire to your parking brake circuits ground wire. This wire will allow you to use the T3s more advanced functions that are only available when parked. If you are installing the Infill T3 into a car with an after market amplifier, you should not connect the speaker connectors on the Infill harness, but rather leave them disconnected and connect the front, rear, and optionally center and sub RCA connectors on the bottom Infill unit directly to your amp.
INSTALLATION
After you have prepared the wiring harness for the Infill T3, you should now wire up all the accessories you are installing for your Infill T3. Unscrew and remove the plastic panel covering the pillars on either side of the windshield.
If installing the optional TV antenna, run the wires for it to the top corners of the windshield now. Attach each of the large central pieces to a corner, with the smaller arms stretching perpendicular to each other.
Run any additional wires to where they need to go: Video feed (Yellow RCA labeled BACK) to an optional rear-view camera, run under the carpet or through the pillar, tucked into the plastic rim around the top of the door, etc. Optional USB extensions to dashboard. GPS to top of dash or inside glove compartment. If using an amplifier, extend wires from the T3 to your amp.
Depending on what kind of car you are installing the Infill T3 in, you may need to remove mounting brackets from your old stereo and use them on the T3 or more then likely you will need a double DIN mounting kit that will include a trim ring and possibly a metal sleeve or other type of fastener to hold the head unit in place. Once the T3 is ready to be installed, hold it near the double DIN opening and connect all wires to the back of the unit, then slide the T3 into the dash opening, but dont fasten anything done yet.
After connecting everything to the T3, while it is still accessible, start your car, make sure the Infill starts up, and test that it is working. Make sure you can start StreetDeck, play a mp3 file or other audio source, test the radio, go into navigation and make sure you receive a GPS signal (you may have to pull your car outside the garage if you cant get a signal), if you installed the diversity antenna, you should test the TV, Test that the remote control works, the arrow buttons should change the focus of the selected button in StreetDeck. If you connected the ILL wire on the harness, turn on your headlights and make sure the display dims. Close StreetDeck and go to Windows, go to Start | Control Panel, choose Network Connections | Wireless Network Connection choose View Wireless Networks and see if you can connect to your home wireless network if setup. Make sure when you turn off your car the Infill turns off with it. Once you are sure there are no problems with your Infill T3, finish securing it and put back any trim panels or other pieces you needed to remove to install it.
WIRE GUIDE
The following pages will help you identify each of the wires on the back of the Infill T3 and what it should be plugged into.
Power adapter wires: Red: Connect to red 5 volt accessory wire. This wire will tell the T3 when the car is on so that it will turn on or wake up from sleep. Yellow: Connect to yellow +12 volt always on wire. This wire will provide most of the T3s power. Black: Connect to black ground wire, or the metal frame of the car.
Large black proprietary cable: Connects to the matching cable on the other unit. NOTE: This connection should be reinforced by wrapping the ends of the two connectors with electrical tape. If it becomes disconnected, it will render the T3 nonfunctional.
Yellow TV OUT: Connect to Yellow TV IN on bottom unit. Red FRONT RIGHT: Connect to red FRONT RIGHT on bottom unit.* White FRONT LEFT: Connect to white FRONT LEFT on bottom unit.* Red REAR RIGHT: Connect to red REAL RIGHT [sic] on bottom unit.* White REAR LEFT: Connect to white REAL LEFT [sic] on bottom unit.* Red LINE OUT RIGHT: Connect to red LINE IN RIGHT on bottom unit. White LINE OUT LEFT: Connect to white LINE IN LEFT on bottom unit. Radio jack: Connect to radio antenna. NOTE: Some car models may need an adapter to work with the T3 antenna connector. These can be found at http://www.crutchfield.com/.
Power port: Connect to matching plug from power adapter. The additional wires from the power plug will be enumerated shortly. *If youre using an amplifier, leave these wires disconnected.
Yellow TV IN: Connect to Yellow TV OUT on top unit. Red FRONT RIGHT: Connect to red FRONT RIGHT on top unit.* White FRONT LEFT: Connect to white FRONT LEFT on top unit.* Red REAL RIGHT [sic]: Connect to red REAR RIGHT on top unit.* White REAL LEFT [sic]: Connect to white REAR LEFT on top unit.* Red LINE IN RIGHT: Connect to red LINE OUT RIGHT on top unit. White LINE IN LEFT: Connect to white LINE OUT LEFT on top unit. Yellow BACK: Connect to rear view camera, for video feed. Yellow VIDEO IN: Connect to an auxiliary video source, such as a videogame console. Red AUX RIGHT: Right audio input used with the auxiliary video source. White AUX LEFT: Left audio input used with the auxiliary video source. Orange WOOFER: In a 5.1 audio setup, this connects to a subwoofer.* Blue CENTER: In a 5.1 audio setup, this connects to a central speaker.* *If youre using an amplifier, do not connect these to the top unit. These wires will instead hook up to the amplifier. The WOOFER and CENTER wires are hooked up to the appropriate channels on the amp.
Black USB x2: Connect to optional USB accessories. (Bluetooth, external hard drive, etc.) Also included are two USB extenders to let the USB slots reach to your dashboard.
Power port: connect to matching plug from power adapter. The additional wires from the power plug will be enumerated shortly.
From the botton (CPU) unit: Blue AMP ON: Connect to an external amplifier (if applicable). This wire will power your amp on when appropriate. Orange ILL: Connect to the matching illumination wire from your cars harness. This wire will tell the Infill when your headlights are on and will automatically dim the screen. White BACK: Connect to your reverse light in the rear. This wire will tell the T3 when you are backing up, making it show the rear-view camera (if one is set up) Green HAND BREAK [sic]: Connect to the parking brake. This wire allows StreetDeck to know when it is safe to use certain features. Failure to connect this wire properly will make your T3 illegal to use while driving in many states.