Академический Документы
Профессиональный Документы
Культура Документы
CHAPTER 1
*Frame arms of 135F (57C) sprinklers of some manufacturers are painted black.
Sprinklers of very extra high and ultra high ratings are primarily used for internal protection of chambers such as ovens and dryers having working temperatures above 300F (149C). When the sprinklers are normally heated to the working temperature of the oven or dryer, under accidental fire conditions they will operate fast enough for safe protection. However, when the sprinklers are initially at the same temperature as a cold oven or dryer, operation may be so severely retarded that the oven or dryer is virtually without internal sprinkler protection. Specially coated or plated sprinklers are available for use where corrosion resistance is desired and decorative coated sprinklers are available for areas where improved appearance is desired. For corrosion resistance, wax is satisfactory except in extreme atmospheres. Wax has too low a melting point for high-degree heads, whereas a bituminous coating affords some protection. A lead coating protects against certain mild corrosive atmospheres. Wax-over-lead provides good sprinkler protection. Corrosion resistant sprinklers such as those manufactured from stainless steel or other corrosion resistant materials currently afford the best available protection. Common decorative finishes are bright brass, chrome, paint, or polyester coating. These finishes are for decorative purposes only and are not FM Approved for corrosion resistance. Only sprinklers supplied by the listed manufacturers are FM Approved. Any change in the device after it leaves the manufacturer voids the Approval. Coated, plated and painted sprinklers rated above 165F (74C) have the standard temperature color code either on the frame arms or on the compression screws, except in the case of bulb type decorative coated sprinklers in which the bulb fluid color indicates the temperature rating per the following table:
Temperature Rating F (C) 135 (57) 155 (68) 175 (79) 200 (93) 250, 286 (121, 141) 325, 360 (162, 182) 400650 (204343) Bulb Color Code Orange Red Yellow Green Blue Mauve Black
When selecting a specific type of sprinkler, refer to the FM Global Property Loss Prevention Data Sheets to ensure that the sprinkler selected is capable of providing adequate fire protection for the intended occupancy. In addition, working plans of proposed layouts, showing all details with respect to location of sprinklers and piping, description
1-2
of the occupancy and details of construction, should be sent to your insurance company for review before the materials are fabricated. The plans will be accepted or changes will be recommended to assure that the work will be done according to the best practice and to avoid the possibility of later requests for changes. Unless otherwise noted, automatic sprinkler system components, which are subjected to system water pressure, have a rated working pressure of 175 psi (1205 kPa). In this section, FM Approved sprinklers are listed in a tabular format. Because this format limits the space in which the information can be provided, the following conventions are used: The sprinkler nominal discharge coefficient (K-factor) is expressed in US customary units of gal/min/(psi). Sprinkler response categories are abbreviated as follows:
SR QR FR Quick Response Suppression Mode Fast Response Standard Response
Heat responsive elements are identified as either Fusible or, in the case of bulb type elements, with the nominal bulb diameter in millimeters (e.g., 2.5 mm, 3 mm, etc.) Nominal thread sizes are expressed using American National Standard Taper Pipe Threads (NPT). Sprinklers intended for sale outside the United States shall have threads which are in compliance with other national or international standards as permitted at the sole discretion of FM Approvals. Sprinkler finishes are identified as follows:
Finish Brass Chrome Black Plated Bright Brass Lead Wax Wax Over Lead Polyester Painted Unfinished, Plain Brass or Bronze Chrome Plated Black Plated Bright Brass Plated Lead Coated (for extra corrosion protection in some atmospheres) Wax Coated (for extra corrosion protection in some atmospheres) Wax Over Lead Coated (for extra corrosion protection in some atmospheres) Polyester Coated (any color) Painted (any color) Description
Sprinkler nominal temperature ratings are expressed in degrees Fahrenheit (F) followed by the equivalent in degrees Celsius (C). Company names are abbreviated in the individual listings.
Company Anber Globe Angus CPF GW Globe Grinnell Kidde Nanjing Minimax Paradise Reliable Rolland Senju Spraying Sys Tyco Tyco Mfg Ltd Victaulic Viking Viking SA Manufacturers Name and Address Anber Globe SA, Av de Las Flores 13, Parque Ind El Molino, 28970 Humanes de Madrid, Madrid Spain Angus Fire Sprinklers, Thame Park Rd, Oxfordshire 0X9 3RT, United Kingdom CPF Industriale SpA, Via E Fermi, 98-25064 Gussago Brescia, Italy GW Sprinkler A/S, Kastanievej 15 DK-5620 Glamsbjerg Denmark Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658 Grinnell Corp, 3 Tyco Park, Exeter NH 03833 Kidde Fire Fighting, 2 Executive Way, Ranson WV 25438 Nanjing Fire Protection Technology Co Ltd, 12 Shiyang Rd, Baxia District, Nanjing, China Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany Paradise Industry Co, Ltd, 65-2 Chooneui-Dong, Woonmi-Ku, Bucheon-City, Kyunggi-Do Korea (420-120) Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313 Rolland Arroseurs Sprinklers, Ste Rolland/Usine, 73410 Mognard, France Senju Sprinkler Co Ltd, 23 Senju-Hashido-Cho Adachi-Ku Tokyo Japan 120 Spraying Systems Co, North Ave at Schmale Rd, Box 7900, Wheaton IL 60189 Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446 Tyco Fire Products Manufacturing Ltd, Stockport Trading Estate, Yew St Stockport, Cheshire SK4 2JW, United Kingdom Victaulic Company, Box 31, Easton PA 18044 The Viking Corp, 210 N Industrial Park Rd, Hastings MI 49058 Viking SA, Zone Industrielle Haneboesch, L-4562, Differdange/Niedercorn, Luxembourg
FM Approvals
1-3
Control Mode Sprinklers Open Sprinklers, Control Mode (Specific Application) Window and Cornice
Window and cornice sprinklers are open sprinklers designed to protect windows and combustible cornices against outside exposing fires. Window and cornice sprinklers have no automatic operating element and are available in various nominal orifice sizes. Their operation depends usually on the opening of a control valve by hand, although they are sometimes automatically controlled with a thermostatically operated deluge valve.
Open Sprinklers, Control Mode (Specific Application) Window and Cornice (Class 2014)
Company Grinnell Grinnell Grinnell Reliable Reliable Reliable Reliable Reliable Reliable Reliable Reliable Spraying Sys Spraying Sys Spraying Sys Spraying Sys Viking Viking Viking Viking Model Issue A Issue A Issue A R0413 R0414 R0415 R0418 R0416 R0411 R0428 R0426 FM-12K60 FM-12K80 FM-34K120 FM-34K210 VK790 VK791 VK792 VK793 Orifice Size
14 516 38 14 516 38 12 58 34 12 58
NPT
1 2 1 2 1 2 1 2 1 2 1 2 1 2 3 4 3 4 1 2 3 4 1 2 1 2 3 4 3 4 1 2 1 2 1 2 1 2
Type Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Cornice Sprinkler Cornice Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler Window Sprinkler
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
FM Approvals
1-4
Finishes Brass, Chrome, Wax, Lead, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass, Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Wax, Wax Over Lead Brass, Chrome, Wax Brass Brass, Chrome, Wax
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 165, 212F (57, 74, 100C) 165, 212F (74, 100C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 155, 200F (68, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 165, 220F (74, 104C) 135, 155, 175, 200F (57, 68, 79, 93C)
Finishes Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Brass, Chrome
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Finishes Brass, Chrome, Wax, Lead, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass, Lead Wax, Wax Over Lead Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 165, 212F (57, 74, 100C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200F (57, 68, 79, 93C)
FM Approvals
1-5
Response SR SR SR
Element 5 mm Fusible 5 mm
NPT (in.)
1 2 1 2 1 2
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 165, 220F (74, 104C) 135, 155, 175, 200F (57, 68, 79, 93C)
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Finishes Brass Brass Brass Brass Brass, Chrome Brass, Chrome Brass 165F (74C) 165F (74C) 165F (74C) 165F (74C)
135, 155, 175, 200, 212F (57, 68, 79, 93, 100C) with E-1 Recessed Escutcheon 135, 155, 175, 200, 212F (57, 68, 79, 93, 100C) with E-2 Threaded Recessed Escutcheon 155, 175, 200F (68, 79, 93C)
FM Approvals
1-6
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome Brass, Chrome, Polyester Brass, Chrome, Polyester Wax, Lead, Wax Over Lead Brass, Bright Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome Chrome Brass, Chrome, Black Plated, Bright Brass Wax, Lead, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass Brass, Chrome Brass Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Wax, Lead, Wax Over Lead
Temp Ratings, F (C) 135, 155, 175, 200, 286 (57, 68, 79, 93, 141 ) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (68, 79, 93C) 135, 155, 175, 200F (57 , 68, 79, 93C) 155, 200F (68, 93C) 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 162, 205, 282F (72, 96, 139C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 165, 212, 280F (74, 100, 138C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C)
FM Approvals
1-7
Response SR SR SR SR
Element 5 mm Fusible 5 mm 5 mm
NPT (in.)
1 2 1 2 1 2 1 2
Finishes Brass, Chrome, Wax, Polyester Brass, Polyester Brass, Chrome, Wax, Polyester Brass, Chrome, Wax
Temp Ratings, F (C) 135, 155, 175, 200, 212, 286, 360, 500F (57, 68, 79, 93, 100, 141, 182, 260C) 165, 220, 286F (74, 104, 141C) 135, 155, 175, 200, 212, 286, 360, 500F (57, 68, 79, 93, 100, 141, 182, 260C) 135, 155, 175, 200, 212, 286, 360, 500F (57, 68, 79, 93, 100, 141, 182, 260C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Plated Brass, Chrome Chrome Brass, Chrome, Bright Brass Brass, Chrome Brass, Chrome, Bright Brass, Polyester Brass, Chrome Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Wax, Lead, Wax Over Lead Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57,68,79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 200F (57, 68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F, (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 155, 200F (68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 205F, (74, 96C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
FM Approvals
1-8
Finishes Brass, Chrome Brass, Chrome, Polyester Brass, Chrome Brass, Chrome, Polyester Brass, Chrome, Polyester Wax, Lead, Wax Over Lead Brass, Bright Brass, Chrome, Lead Wax, Wax Over Lead Chrome Brass, Chrome, Black Plated, Bright Brass Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass Brass, Bright Brass, Chrome, Black Plated, Polyester Brass, Chrome Brass Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead
Temp Ratings, F (C) 135, 155, 175, 200, 286 (57, 68, 79, 93, 141) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (68, 79, 93C) 155, 200F (68, 93C) 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 162, 205, 282F (72, 96, 139C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 165, 212, 280F (74, 100, 138C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C)
FM Approvals
1-9
Response SR SR SR SR
Element 5 mm 5 mm Fusible 5 mm
NPT (in.)
1 2 1 2 1 2 1 2
Finishes Wax, Wax Over Lead Brass, Chrome, Polyester, Wax Brass, Polyester Brass, Chrome, Polyester, Wax
Temp Ratings, F (C) 155, 200F (68, 93C) 135, 155, 175, 200, 212, 286, 360, 500F (57, 68, 79, 93, 100, 141, 182, 260C) 165, 220, 286F (74, 104, 141C) 135, 155, 175, 200, 212, 286, 360, 500F (57, 68, 79, 93, 100, 141, 182, 260C)
Finishes Brass, Chrome Brass, Chrome, Polyester Brass, Chrome Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass Chrome Chrome Brass, Chrome, Bright Brass Brass, Bright Brass, Chrome, Black Plated, Polyester Brass, Chrome Chrome Brass, Chrome, Bright Brass, Polyester Brass Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Wax, Wax Over Lead Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155, 200F (57, 68, 93C) 135, 155, 200F (57, 68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 155F (68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 205F (74, 96C)
FM Approvals
1-10
Company Viking SA
Model VK302
K 5.6
Type Pendent
Response QR
Element 3 mm
NPT (in.)
1 2
Temp Ratings, F (C) 135, 155, 175, 200, 286F, (57, 68, 79, 93, 141C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Brass, Bright Brass, Chrome, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Wax, Lead, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass, Lead Wax, Wax Over Lead Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass, Lead Brass, Chrome, Black Plated, Bright Brass Lead, Wax, Wax Over Lead Lead, Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass Brass, Chrome, Polyester Wax Brass, Chrome 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212F (74, 100C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 135, 165, 212, 286F (57, 74, 100, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93C) 135, 155, 200F (57, 68, 93C) 165, 212, 280F (74, 100, 138C)
FM Approvals
1-11
Company Tyco Tyco Tyco Tyco Tyco Mfg Ltd Tyco Mfg Ltd Victaulic Victaulic Viking Viking Viking Viking Viking SA Viking SA
Model TY3351 TY3351 TY3451 TY3451 TY3304 TY3451 V2709 V2709 VK104 VK106 VK112 VK114 VK104 VK106
K 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6
Type Horizontal Sidewall Horizontal Sidewall Vertical Sidewall Vertical Sidewall Horizontal Sidewall Vertical Sidewall Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Vertical Sidewall Horizontal Sidewall Vertical Sidewall Horizontal Sidewall Vertical Sidewall
Response SR SR SR SR SR SR SR SR SR SR SR SR SR SR
NPT (in.)
12 12 12 12 12 12 12 12 12 12 12 12 12 12
Temp Ratings, F (C) 135, 155, 175, 200, 286F, 360F (57, 68, 79, 93, 141, 182C ) 135, 155, 200F (57, 68, 93C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, Polyester 141, 182C) Wax Brass, Chrome, Polyester 135, 155, 200F (57, 68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93C)
Brass, Chrome, Bright Brass, 135, 155, 200, 286F (57, 68, 93, 141C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester, Lead Wax, Wax Over Lead Brass, Chrome Brass, Chrome Brass Brass, Chrome Brass, Chrome Brass, Chrome 155, 200F (68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 220, 286F (74, 104, 141C) 165, 220, 286F (74, 104, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93C) Polyester Brass, Chrome 165, 212F (74, 100C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester
FM Approvals
1-12
Company Tyco Mfg Ltd Tyco Mfg Ltd Tyco Mfg Ltd Victaulic Viking Viking Viking Viking SA Viking SA
Model TY3305 TY3331 TY3431 V2710 VK304 VK305 VK306 VK304 VK306
Type Horizontal Sidewall Horizontal Sidewall Vertical Sidewall Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Vertical Sidewall Horizontal Sidewall Vertical Sidewall
Response QR QR QR QR QR QR QR QR QR
Element 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm
NPT (in.)
12 12 12 12 12 12 12 12 12
Finishes
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester, Lead Brass, Chrome Brass Brass, Chrome Brass, Chrome Brass, Chrome 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy 316L (UNS-NO8367) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C)
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C)
FM Approvals
1-13
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy 316L (UNS-NO8367) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C)
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome Brass Brass, Chrome, Bright Brass Brass Brass 155F (68C) 155F (68C)
135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 165, 212F (57, 74, 100C) 135, 165, 212F (57, 74, 100C)
FM Approvals
1-14
Company Reliable Reliable Reliable Reliable Reliable Reliable Senju Tyco Tyco Tyco Tyco Tyco Tyco Tyco Mfg Ltd Tyco Mfg Ltd Victaulic Victaulic Viking Viking Viking Viking Viking Viking SA
Model R1715 R2215 R2218 R5415 R5418 RA1314 SS2531 TY3204 TY3211 TY3251 TY3504 TY3505 TY3551 TY3204 TY3251 V2707 V3802 VK102 VK102 VK302 VK400 VK404 VK102
K 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6
Type Recessed Pendent Concealed Pendent Adj. Concealed Pendent Concealed Pendent Adj. Concealed Pendent Recessed Pendent Flush Pendent Recessed Pendent Recessed Pendent Recessed Pendent Adj. Concealed Pendent Adj. Concealed Pendent Adj. Concealed Pendent Recessed Pendent Recessed Pendent Recessed Pendent Concealed Pendent Recessed Pendent Concealed Pendent Concealed Pendent Flush Pendent Concealed Pendent Recessed Pendent
Response SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR
NPT (in.)
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
Finishes Brass, Chrome, Black Plated, Bright Brass Brass Brass Brass Brass Brass, Bright Brass, Chrome, Black Plated, Polyester Chrome, Painted Brass, Chrome, Bright Brass Brass, Chrome Brass, Chrome, Bright Brass Brass Brass Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass, Polyester Brass Brass, Chrome, Polyester Brass Brass Brass, Chrome, Polyester Brass Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 165F (74C) 165F (74C) 165F (74C) 165F (74C) 135, 155, 175, 200F (57, 68, 79, 93C) 162F , 205F (72, 96C) 135, 155, 175, 200F (57, 68, 79, 93C) * 165, 212F (74, 100C) 135, 155, 175, 200F (57, 68, 79, 93C) * 155, 200F (68, 93C) 155, 200F (68, 93C) 155, 200F (68, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) * 135, 155, 175, 200F (57, 68, 79, 93C) * 135, 155, 175, 200F (57, 68, 79, 93C) 155, 175, 200F (68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) with Viking E-1 or E-2 Recessed Escutcheon 155, 175, 200F (68, 79, 93C) with Viking E-1 or E-2 Recessed Escutcheon 155, 175, 200F (68, 79, 93C) with Viking E-1 or E-2 Recessed Escutcheon 165, 220F (74, 104C) 165F (74C) 135, 155, 175, 200, (57, 68, 79, 93) with Viking E-1, or E-2 Recessed Escutcheon
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass Brass, Bright Brass, Chrome, Black Plated, Polyester 155F (68C) 155F (68C)
135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
FM Approvals
1-15
Company Tyco Tyco Tyco Mfg Ltd Tyco Victaulic Viking Viking Viking SA
Type Recessed Pendent Recessed Pendent Recessed Pendent Recessed Pendent Recessed Pendent Recessed Pendent Flush Pendent Recessed Pendent
Response QR QR QR QR QR QR QR QR
Element 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm Fusible 3 mm
NPT (in.)
12 12 12 12 12 12 12 12
Finishes Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) with Viking E-1 or E-2 Recessed Escutcheon 165F (74C) 135, 155, 175, 200F (57, 68, 79, 93C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass, Polyester
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
K5.6 Sidewall Flush, Recessed and Concealed, Quick Response (Class 2020)
Company Tyco Tyco Tyco Mfg Ltd Tyco Mfg Ltd Victaulic Model TY3305 TY3331 TY3305 TY3331 V2710 K 5.6 5.6 5.6 5.6 5.6 Type Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Horizontal Sidewall Response QR QR QR QR QR Element 3 mm 3 mm 3 mm 3 mm 3 mm NPT (in.)
12 12 12 12 12
Finishes Brass, Chrome, Bright Polyester Brass, Chrome, Bright Polyester Brass, Chrome, Bright Polyester Brass, Chrome, Bright Polyester Brass, Chrome, Bright Polyester, Lead
Temp Ratings, F (C) Brass, Brass, Brass, Brass, Brass, 135, 155, 175, 200 F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200 F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
K5.6 Dry
Control mode dry automatic sprinklers are similar to other control mode sprinklers except that the sprinkler body is permanently secured to an extension nipple which includes a valve at the inlet end to prevent water from entering the nipple until the sprinkler operates. The sprinkler is threaded into a pipe fitting above the ceiling or enclosure at the valve end, thus replacing a drop nipple. The purpose of these devices is (1) to eliminate possible freezing due to the collection of condensation in the drop nipple (2) to eliminate the need to remove standard pendent sprinklers installed in a dry-pipe system in order to drain the system after flooding, and (3) to provide protection for unheated areas such as store windows or food freezers using a wet system in which the sprinkler pipes are located in a heated area. Unless otherwise noted, FM Approved dry sprinklers are limited to a maximum nominal length of 48 in. (1.2 m).
FM Approvals
1-16
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
FM Approvals
1-17
Company Victaulic
Model V3606
K 5.6
Response QR
Element 3 mm
NPT (in.) 1
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
FM Approvals
1-18
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
K5.6 Dry Flush, Recessed and Concealed, Quick Response (Class 2020)
Company Globe Globe Tyco Victaulic Victaulic Model GL5635* GL5641* TY3235 V3606 V3610 K 5.6 5.6 5.6 5.6 5.6 Type Dry Recessed Pendent Dry Recessed Horizontal Sidewall Dry Recessed Pendent Dry Recessed Pendent Dry Recessed Horizontal Sidewall Response QR QR QR QR QR Element 3 mm 3 mm 3 mm 3 mm 3 mm NPT (in.) 1 1 1 1 1 Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome Brass, NICOTEF Coated Brass, NICOTEF Coated Temp Ratings, F (C) 155, 200F (68, 93C) 155, 200F (68, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 200F (57, 68, 93C) 135, 155, 200F (57, 68, 93C)
* Approval of these dry sprinklers is limited to a maximum nominal length of 36 in. (0.91 m).
FM Approvals
1-19
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212, 280F (74, 100, 138C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141,182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 220, 286F (74, 104, 141C)
Type Rack Storage Upright Rack Storage Upright Rack Storage Upright Rack Storage Upright Rack Storage Upright Rack Storage Upright Rack Storage Upright
Response QR QR QR QR QR QR QR
Element 3 mm 3 mm Fusible 3 mm 3 mm 3 mm 3 mm
NPT (in.)
12 12 12 12 12 12 12
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Model S S GL5672
Type Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent
Response SR SR SR
Element 5 mm 5 mm 5 mm
NPT (in.)
12 12 12
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C)
FM Approvals
1-20
Type Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent Rack Storage Pendent
Response SR SR SR SR SR SR SR SR
NPT (in.)
12 12 12 12 12 12 12 12
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 165, 212, 286F (57, 74, 100, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C )
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, Polyester 93, 141, 182, 260C) Brass, Chrome, Bright Brass, 135, 155,175, 200, 286, 360, 500F (57, 68, 79, Polyester 93, 141, 182, 260C) Brass Brass Brass 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 220, 286F (74, 104, 141C)
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester Brass 165, 212F, (74, 100C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) Polyester Brass Brass Brass 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
FM Approvals
1-21
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester 175F (79C) 175F (79C)
Extended Coverage Light Hazard (ECLH) K5.6 Pendent, Quick Response (Class 2020)
Company Tyco Viking Viking SA Model TY3232 VK600 VK600 K 5.6 5.6 5.6 Type Pendent Pendent Pendent Response QR QR QR Element 3 mm 3 mm 3 mm NPT (in.)
12 12 12
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 155F (68C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester 175F (79C) 175F (79C)
Extended Coverage Light Hazard (ECLH) K5.6 Sidewall, Quick Response (Class 2020)
Company Reliable Tyco Tyco Tyco Tyco Mfg Ltd Model R4865 TY3302 TY3322 TY3332 TY3332 K 5.6 5.6 5.6 5.6 5.6 Type Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Response QR QR QR QR QR Element 3 mm 3 mm Fusible 3 mm 3 mm NPT (in.)
12 12 12 12 12
Finishes
Brass, Chrome, Bright Brass, 135, 155, 175F (57, 68, 79C) Black Plated, Polyester Brass, Chrome, Bright Brass, 155F (68C) Polyester Brass, Chrome Brass, Chrome, Polyester Brass, Chrome, Polyester 165F (74C) 135, 155F (57, 68C) 135, 155F (57, 68C)
K5.6 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent or Sidewall)
Control mode, Extended Coverage-Light Hazard (ECLH) flush, recessed and concealed sprinklers are ECLH sprinklers intended for use with a concealed piping system. Flush pendent types are constructed with an operating element which extends a short distance below the ceiling. Upon actuation, the sprinkler deflector drops below the ceiling level to provide a proper water distribution. Recessed pendent types consist of a sprinkler installed in a decorative recessed cup which reduces the protrusion of the sprinkler from the ceiling. Concealed pendent types incorporate a cover plate which is heat activated and can be manually removed to prevent over-painting of the cover plate. Sidewall flush, recessed and concealed sprinklers are similar to pendent flush recessed and concealed sprinklers except that they are designed to be installed in a wall near the junction of the ceiling and wall. They are equipped with a special deflector which discharges most of the water in a forward direction. All of these sprinkler types are intended for use in light hazard occupancies where attractive apearance under a ceiling is desired.
FM Approvals
1-22
The FM Global Property Loss Prevention Data Sheets should be closely followed when designing and installing automatic fire protection systems utilizing these sprinklers. Quick response ECLH flush recessed and concealed sprinklers are FM Approved for use in Wet Systems and Pre-action Systems qualifying as Wet Systems only.
Extended Coverage Light Hazard (ECLH) Flush, Recessed and Concealed (Class 2022)
Company Tyco Tyco Mfg Ltd Viking Model TY3332 TY3332 VK600 K 5.6 5.6 5.6 Type Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Pendent Response SR SR SR Element 3 mm 3 mm 3 mm NPT (in.)
1 2 1 2 1 2
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 175F (79C) 175F (79C) 175F (79C)
Extended Coverage Light Hazard (ECLH) Flush, Recessed and Concealed, Quick Response (Class 2020)
Company Reliable Tyco Tyco Tyco Tyco Mfg Ltd Viking Model R4865 TY3232 TY3302 TY3332 TY3332 VK600 K 5.6 5.6 5.6 5.6 5.6 5.6 Type Recessed Horizontal Sidewall Recessed Pendent Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Pendent Response QR QR QR QR QR QR Element 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm NPT (in.)
1 2
Finishes Brass, Chrome, Bright Brass, Black Plated, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 135F (57C) 155F (68C) 155F (68C)
1 2 1 2 1 2 1 2 1 2
135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155F (57, 68C)
Finishes Wax Wax Wax Wax Wax, Wax Over Lead 286F (141C) 286F (141C) 286F (141C) 286F (141C) 286F (141C)
FM Approvals
1-23
Finishes Wax Wax Wax Wax Wax, Wax Over Lead 286F (141C) 286F (141C) 286F (141C) 286F (141C) 286F (141C)
Finishes Brass Brass Wax, Wax Over Lead 286F (141C) 286F (141C) 286F (141C)
Finishes Brass
Finishes Brass
FM Approvals
1-24
NPT (in.)
3 4
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester, Brass, Chrome, Polyester Wax, Lead, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass Brass, Chrome, Black Plated, Bright Brass Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Polyester Brass, Chrome Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (68, 79, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (68, 79, 93C) 135, 165, 212, 286F (57, 74, 100, 141C) 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 212, 280, 360F (74, 100, 138, 182C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 165, 212, 280F (74, 100, 138C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C)
and 34 and 34
3 4 3 4 1 2 1 2 3 4 3 4 1 2 3 4 3 4 3 4 3 4
and 34
3 4 3 4 3 4 3 4 1 2 1 2 1 2 3 4 1 2 3 4
FM Approvals
1-25
Response SR SR SR SR SR SR
Element 5 mm 5 mm 5 mm Fusible 5 mm 5 mm
NPT (in.)
3 4 1 2 1 2
Finishes Wax, Lead, Wax Over Lead Brass, Chrome, Polyester Wax Brass, Polyester Brass, Chrome Wax
Temp Ratings, F (C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200F (57, 68, 79, 93C) 165, 220, 286F (74, 104, 141C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200F (57, 68, 79, 93C)
and 34 and 34
3 4
1 2 1 2
and 34 and 34
NPT (in.)
3 4
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass, Polyester
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
and 34 and 34
1 2 3 4 1 2 3 4 3 4
and
3 4 3 4 3 4 3 4 3 4
34
Brass, Chrome Brass, Chrome Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Brass, Chrome, Polyester
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
FM Approvals
1-26
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
NPT (in.)
3 4
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Wax, Lead, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Black Plated, Bright Brass
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (57, 68, 79C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 175, 200F (57, 68, 79C) 135, 165, 212, 286F (57, 74, 100, 141C)
and 34 and 34
1 2 3 4 3 4 1 2 1 2 3 4 3 4 1 2
FM Approvals
1-27
Company Reliable Reliable Reliable Reliable Rolland Tyco Tyco Tyco Tyco Tyco Tyco Tyco Tyco Mfg Ltd Tyco Mfg Ltd Victaulic Victaulic Viking Viking Viking Viking SA Viking SA
Model R1017 R1017 R1017 R1712 N TY4211 TY4211 TY4251 TY4251 TY4911 TY4911 TY4951 TY4251 TY4951 V3405 V3405 VK202 VK202 VK206 VK202 VK202
K 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
Type Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent
Response SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR SR
NPT (in.)
3 4 3 4 3 4 3 4 1 2
Finishes Brass, Chrome, Black Plated, Bright Brass Lead Wax, Wax Over Lead Brass, Chrome, Black Plated Brass, Chrome Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Wax Brass, Chrome Wax, Lead Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Wax, Wax Over Lead Brass, Chrome Wax Brass Brass, Chrome Wax
Temp Ratings, F (C) 135, 165, 212, 286F (57, 74, 100, 141C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 212, 280F (74, 100, 138C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 200F (57, 68, 93C) 165, 212, 280, 360F (74, 100, 138, 182C) 165, 212F (74, 100C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 155, 200F (68, 93C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200F (57, 68, 79, 93C) 165, 220, 286F (74, 104, 141C) 135, 155, 175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200F (57, 68, 79, 93C)
and 34
3 4 3 4 3 4 3 4 1 2 1 2 1 2 3 4 1 2 3 4 3 4
1 2 1 2
and 34 and 34
3 4
1 2 1 2
and 34 and 34
NPT (in.)
3 4
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175F (57, 68, 79C)
and 34
FM Approvals
1-28
Company GW Globe Globe Kidde Kidde Reliable Rolland Tyco Tyco Tyco Mfg Ltd Victaulic Viking
Model S GL8101 GL8106 AS8051 AS8053 R3612 N TY4221 TY4231 TY4231 V3406 VK352
K 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
Type Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent Pendent
Response QR QR QR QR QR QR QR QR QR QR QR QR
Element 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm Fusible 3 mm 3 mm 3 mm 3 mm
NPT (in.)
1 2
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome, Bright Brass Brass, Chrome Brass, Chrome Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Bright Brass, Polyester, Lead Brass, Chrome
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
and 34
1 2 3 4 1 2 3 4 3 4
1 2
and 34
3 4 3 4 3 4 3 4 3 4
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C)
and
34
and 34
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C)
and
34
and 34
FM Approvals
1-29
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C)
and
34
and 34
Finishes AISI 316 (UNS S31254) Stainless Steel Alloy AISI 316 (UNS S31254) Stainless Steel Alloy
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C)
and 34 and 34
NPT (in.)
12 34 34 34 12 34
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Black Plated, Bright Brass Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200F (57, 68, 79, 93C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200F (57, 68, 79, 93C) Polyester Brass, Chrome 135, 155, 175, 200F (57, 68, 79, 93C)
and 34
FM Approvals
1-30
K 8.0 8.0
Response SR SR
Element 5 mm 3 mm
NPT (in.)
34 34
Temp Ratings, F (C) 155, 175, 200F (68, 79, 93C) 155, 175, 200F (68, 79, 93C)
K8.0 Dry, Flush, Recessed and Concealed (Pendent or Sidewall) K8.0 Dry Flush, Recessed and Concealed (Class 2015)
Company Victaulic Model V3607* K 8.0 Type Dry Recessed Pendent Response SR Element 5 mm NPT (in.) 1 Finishes Brass, NICOTEF Coated Temp Ratings, F (C) 135, 155, 200F (57, 68, 93C)
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Bright Brass
Temp Ratings, F (C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
Brass, Chrome, Bright Brass, 135, 155, 175, 200F (57, 68, 79, 93C) Polyester Brass, Chrome, Bright Brass, 135, 155, 175, 200F (57, 68, 79, 93C) Polyester Brass, Chrome Brass, Chrome 135, 155, 175, 200F (57, 68, 79, 93C) 135, 155, 175, 200F (57, 68, 79, 93C)
34 34
K8.0 Dry Flush, Recessed and Concealed, Quick Response (Class 2020)
Company Victaulic Model V3608* K 8.0 Type Dry Recessed Pendent Response QR Element 3 mm NPT (in.) 1 Finishes Brass, NICOTEF Coated Temp Ratings, F (C) 135, 155, 200F (57, 68, 93C)
*Approval of these dry sprinklers is limited to a maximum nominal length of 30 in. (0.76 m).
FM Approvals
1-31
Finishes Brass Brass Brass Brass Brass Brass Brass Brass Brass Brass
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 165, 212, 286F (57, 74, 100, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 212, 280F (74, 100, 138C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 220, 286F (74, 104, 141C)
Finishes Brass Brass Brass Brass Brass Brass Brass Brass Brass Brass
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
FM Approvals
1-32
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass Brass Brass Brass Brass Brass Brass, Chrome, Polyester Brass Brass Brass
Temp Ratings, F (C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 212, 280F (74, 100, 138C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 165, 212, 286F (57, 74, 100, 141C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155,175, 200, 286, 360, 500F (57, 68, 79, 93, 141, 182, 260C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 135, 155, 175, 200, 286, 360F (57, 68, 79, 93, 141, 182C) 165, 220, 286F (74, 104, 141C)
and 34 and 34
34 12 34 34 34 34 34 34 34 34
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass Brass Brass Brass Brass Brass, Chrome, Polyester Brass Brass Brass
Temp Ratings, F (C) 135, 155, 175F (57, 68, 79C) 135, 155, 175F (57, 68, 79C) 135, 155, 175, 200, 286F (57,68,79,93, 141C) 135, 155, 175, 200, 286F (57,68,79,93, 141C) 135, 155F (57, 68C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
and 34 and 34
12 34 34 34 34 34 34 34 34
FM Approvals
1-33
Finishes Wax Wax Wax Wax, Wax Over Lead 286F (141C) 280F (138C) 286F (141C) 286F (141C)
Finishes Wax Wax Wax Wax Wax Wax, Wax Over Lead 286F (141C) 286F (141C) 280F (138C) 286F (141C) 286F (141C) 286F (141C)
Temp Ratings, F (C) 400, 500F (204, 260C) 400, 500F (204, 260C)
FM Approvals
1-34
coefficient of 5.6 gal/min/(psi) have a maximum spacing (width by length) of 16 ft by 20 ft (4.9 m by 6.1 m). Horizontal sidewall ECLH sprinklers with a nominal discharge coefficient of 8.0 gal/min/(psi) have a maximum spacing (width by length) of 16 ft by 24 ft (4.9 m by 7.3 m). The FM Global Property Loss Prevention Data Sheets should be closely followed when designing and installing automatic fire protection systems utilizing these sprinklers. FM Approved ECLH sprinklers are limited to a maximum temperature rating of 175F (79C).
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester 175F (79C) 175F (79C)
K8.0 Extended Coverage Light Hazard (ECLH), Pendent, Quick Response (Class 2020)
Company Reliable Tyco Viking Viking SA Model R4842 TY4232 VK602 VK602 K 8.0 8.0 8.0 8.0 Type Pendent Pendent Pendent Pendent Response QR QR QR QR Element 3 mm 3 mm 3 mm 3 mm NPT (in.)
34 34 34 34
Brass, Chrome, Bright Brass, 135, 155F (57, 68C) Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 135, 155F (57, 68C) 135, 155F (57, 68C)
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 175F (79C) 175F (79C) 135F (57C)
K8.0 Extended Coverage Light Hazard (ECLH), Sidewall, Quick Response (Class 2020)
Company Reliable Tyco Tyco Model R4862 TY4322 TY4332 K 8.0 8.0 8.0 Type Horizontal Sidewall Horizontal Sidewall Horizontal Sidewall Response QR QR QR Element 3 mm Fusible 3 mm NPT (in.)
34 34 34
Finishes
Brass, Chrome, Bright Brass, 135, 155, 175F (57, 68, 79C) Black Plated, Polyester Brass, Chrome Brass, Chrome, Polyester 165F (74C) 135, 155F (57, 68C)
FM Approvals
1-35
Response QR QR QR QR
Element 3 mm 3 mm 3 mm 3mm
NPT (in.)
34 34 34 34
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155F (57, 68C) 135, 155, 175 F (57, 68, 79C)
K8.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent or Sidewall)
Control mode, Extended Coverage-Light Hazard (ECLH) flush, recessed and concealed sprinklers are ECLH sprinklers intended for use with a concealed piping system. Flush pendent types are constructed with an operating element which extends a short distance below the ceiling. Upon actuation, the sprinkler deflector drops below the ceiling level to provide a proper water distribution. Recessed pendent types consist of a sprinkler installed in a decorative recessed cup which reduces the protrusion of the sprinkler from the ceiling. Concealed pendent types incorporate a cover plate which is heat activated and can be manually removed to prevent over-painting of the cover plate. Sidewall flush, recessed and concealed sprinklers are similar to pendent flush recessed and concealed sprinklers except that they are designed to be installed in a wall near the junction of the ceiling and wall. They are equipped with a special deflector which discharges most of the water in a forward direction. All of these sprinkler types are intended for use in light hazard occupancies where attractive appearance under a ceiling is desired. The FM Global Property Loss Prevention Data Sheets should be closely followed when designing and installing automatic fire protection systems utilizing these sprinklers. Quick response ECLH flush recessed and concealed sprinklers are FM Approved for use in Wet Systems and Pre-action Systems qualifying as Wet Systems only.
K8.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Class 2022)
Company Tyco Tyco Mfg Ltd Victaulic Viking Viking Model TY4332 TY4332 V3416 VK602 VK606 K 8.0 8.0 8.0 8.0 8.0 Type Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Horizontal Sidewall Recessed Pendent Recessed Horizontal Sidewall Response SR SR SR SR SR Element 3 mm 3 mm 3 mm 3 mm 3 mm NPT (in.)
34 34 34 34 34
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 175F (79C) 175F (79C) 155F (68C) 175F (79C) 175F (79C) with Viking E-1 or E-2 recessed escutcheon
K8.0 Extended Coverage Light Hazard (ECLH), Flush Recessed and Concealed, Quick Response (Class 2020)
Company Reliable Reliable Tyco Tyco Tyco Mfg Ltd Model R4842 R4862 TY4232 TY4332 TY4332 K 8.0 8.0 8.0 8.0 8.0 Type Recessed Pendent Recessed Horizontal Sidewall Recessed Pendent Recessed Horizontal Sidewall Recessed Horizontal Sidewall Response QR QR QR QR QR Element 3 mm 3 mm 3 mm 3 mm 3 mm NPT (in.)
34 34 34 34 34
Finishes
Brass, Chrome, Bright Brass, 135, 155F (57, 68C) Black Plated, Polyester Brass, Chrome, Bright Brass, 135, 155F (57, 68C) Black Plated, Polyester Brass, Chrome, Bright Brass, 135F (57C) Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester 135, 155F (57, 68C) 135, 155F (57, 68C)
FM Approvals
1-36
Type Recessed Horizontal Sidewall Recessed Pendent Recessed Horizontal Sidewall Recessed Horizontal Sidewall
Response QR QR QR QR
Element 3 mm 3 mm 3 mm 3mm
NPT (in.)
34 34 34 34
Finishes Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135F (57C) 135, 155F (57, 68C) 135, 155F (57, 68C) with Viking E-1 or E-2 recessed escutcheon 135, 155, 175 F (57, 68, 79C)
Finishes Brass
Finishes Brass, Chrome Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead
Temp Ratings, F (C) 165, 212, 286F (74, 100, 141C) 155, 200, 286F (68, 93, 141C) 155, 200F (68, 93C) 155, 200, 286F (68, 93, 141C) 155, 200F (68, 93C)
and
34 34 12 12
3 4
FM Approvals
1-37
Response SR SR SR SR SR SR SR
NPT (in.)
12 12 34 34 34 34 34
Finishes Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Lead Wax, Wax Over Lead Brass, Chrome, Polyester, Lead Wax, Wax Over Lead Brass, Chrome
Temp Ratings, F (C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 165, 212, 286F (74, 100, 141C) 165, 212F (74, 100C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 155, 200F (68, 93C) 155, 175, 200, 286F (68, 79, 93, 141C)
Temp Ratings, F (C) 155, 200, 286F (68, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Finishes Brass, Chrome Brass, Chrome, Lead Wax, Wax Over Lead Brass, Lead Wax, Wax Over Lead
Temp Ratings, F (C) 165, 212, 286F (74, 100, 141C) 155, 200, 286F (68, 93, 141C) 155, 200F (68, 93C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 155, 200F (68, 93C)
Temp Ratings, F (C) 155, 200, 286F (68, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
FM Approvals
1-38
Temp Ratings, F (C) 155, 175, 200, 286F (68, 79, 93, 141C)
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
FM Approvals
1-39
K11.2 Extended Coverage Light Hazard (ECLH) Pendent, Quick Response (Class 2020)
Company Tyco Victaulic Viking Model TY5237 V3412 VK608 K 11.2 11.2 11.2 Type Pendent Pendent Pendent Response QR QR QR Element 3 mm 3 mm 3 mm NPT (in.)
34 34 34
Finishes Brass, Chrome, Polyester, Lead Brass, Chrome, Bright Brass, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155F (57, 68C) 135, 155F. (57, 68C) 135, 155, 175F (57, 68, 79C)
K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent)
Control mode, Extended Coverage-Light Hazard (ECLH) flush, recessed and concealed sprinklers are ECLH sprinklers intended for use with a concealed piping system. Flush pendent types are constructed with an operating element which extends a short distance below the ceiling. Upon actuation, the sprinkler deflector drops below the ceiling level to provide a proper water distribution. Recessed pendent types consist of a sprinkler installed in a decorative recessed cup which reduces the protrusion of the sprinkler from the ceiling. Concealed pendent types incorporate a cover plate which is heat activated and can be manually removed to prevent over-painting of the cover plate. All of these sprinkler types are intended for use in light hazard occupancies where attractive appearance under a ceiling is desired. The FM Global Property Loss Prevention Data Sheets should be closely followed when designing and installing automatic fire protection systems utilizing these sprinklers. Quick response ECLH flush recessed and concealed sprinklers are FM Approved for use in Wet Systems and Pre-action Systems qualifying as Wet Systems only.
K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed Types (Class 2022)
Company Victaulic Model V3411 K 11.2 Type Recessed Pendent Response SR Element 5 mm NPT (in.)
3 4
K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed Types, Quick Response (Class 2020)
Company Tyco Victaulic Viking Model TY5237 V3412 VK608 K 11.2 11.2 11.2 Type Recessed Pendent Recessed Pendent Recessed Pendent Response QR QR QR Element 3 mm 3 mm 3 mm NPT (in.)
3 4 3 4 3 4
Finishes Brass, Chrome, Polyester, Lead Brass, Chrome, Polyester Brass, Chrome, Polyester
Temp Ratings, F (C) 135, 155F (57, 68C) 135F (57C) 135, 155F (57, 68C)
FM Approvals
1-40
Finishes Wax, Wax Over Lead Wax, Wax Over Lead Wax, Wax Over Lead 286F (141C) 286F (141C) 286F (141C)
Finishes Brass
FM Approvals
1-41
Temp Ratings, F (C) 135, 155, 175, 200, 286F (57, 68, 79, 93, 141C)
Temp Ratings, F (C) 135 , 155 , 175 , 200 , 286F (57, 68, 79, 93, 141C) 155, 175, 200, 286F (68, 79, 93, 141C)
K14.0 Extended Coverage Light Hazard (ECLH), Pendent, Quick Response (Class 2020)
Company Tyco Mfg Ltd Victaulic Model TY6237 V3414 K 14.0 14.0 Type Pendent Pendent Response QR QR Element 3 mm 3 mm NPT (in.)
3 4 3 4
Temp Ratings, F (C) 135, 155F, (57, 68C) 135, 155F (57, 68C)
FM Approvals
1-42
K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent)
Control mode, Extended Coverage-Light Hazard (ECLH) flush, recessed and concealed sprinklers are ECLH sprinklers intended for use with a concealed piping system. Flush pendent types are constructed with an operating element which extends a short distance below the ceiling. Upon actuation, the sprinkler deflector drops below the ceiling level to provide a proper water distribution. Recessed pendent types consist of a sprinkler installed in a decorative recessed cup which reduces the protrusion of the sprinkler from the ceiling. Concealed pendent types incorporate a cover plate which is heat activated and can be manually removed to prevent over-painting of the cover plate. All of these sprinkler types are intended for use in light hazard occupancies where attractive appearance under a ceiling is desired.
K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Class 2015)
Company Victaulic Model V3413 K 14.0 Type Recessed Pendent Response SR Element 5 mm NPT (in.)
3 4
K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed, Quick Response (Class 2020)
Company Tyco Mfg Ltd Victaulic Model TY6237 V3414 K 14.0 14.0 Type Recessed Pendent Recessed Pendent Response QR QR Element 3 mm 3 mm NPT (in.)
3 4 3 4
Finishes Brass
FM Approvals
1-43
Finishes Brass
Temp Ratings, F (C) 155, 175, 200, 286F (68, 79, 93, 141C)
FM Approvals
1-44
Automatic Sprinklers, Control Mode (Specific Application), Cooling Tower (Class 2019)
Company Grinnell Grinnell Kidde Model Issue C, Type I Issue C, Type II 38E Nominal 716, 12 in. orifice dia. Orifice Size Type Cooling Tower Nozzle Cooling Tower Nozzle Cooling Tower Nozzle Notes For use in towers with diffusion decks. For use in towers without diffusion decks.
FM Approvals
1-45
Finishes Brass, Chrome, Polyester Brass, Chrome, Brass, Chrome, Painted Brass, Chrome, Painted Brass, Chrome, Painted Polyester White White White
Temp Ratings, F (C) 155, 175F (68, 79C) 155, 175F (68, 79C) 155, 175F (68, 79C) 155, 175F (68, 79C) 165F (74C)
FM Approvals
1-46
Finishes Brass
Temp Ratings, F (C) 155, 200F (68, 93C) 155, 200F (68, 93C) 165, 212F (74, 100C) 165, 214F (74, 101C) 165, 205F (74, 96C)
Finishes Brass
Temp Ratings, F (C) 165, 214F (74, 101C) 165, 205F, (74, 96C)
FM Approvals
1-47
FM Approvals
1-48
Sprinkler Guards/Shields
Sprinkler guards are designed to protect automatic sprinklers from mechanical damage in the event of a minor impact. They can be used on upright or pendent automatic sprinklers. Specific guards listed below for use with Early Suppression Fast Response (ESFR) automatic sprinklers are only intended for use under conveyors, mezzanines or other similar obstructions and are specifically not for use at ceiling level. Sprinkler shields are mounted directly to the sprinkler casting or may accompany the sprinkler guard to protect the thermal sensitive element from retarded operation due to water discharge from nearby sprinklers at higher elevations.
FM Approvals
1-49
Sprinklers FM Approved with VK005, VK108, VK204, VK300, VK350 VK007, VK206, VK302, VK352
FM Approvals
1-50
SIGHT DRAINS
Sight drains may be used in sprinkler systems where the drain discharge outlet is not readily visible. When they are used, the discharge should conform to FM Global Property Loss Prevention Data Sheets and any local health or water department regulations. They are not to be used upstream of a valve or fitting which can trap pressure between the sight drain and the drain line. Unless otherwise noted in the listing, these sight drains have 175 psi (1205 kPa) rated working pressure.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
1, 114, 112, 2 in. NPS 250 psi (1725 kPa) rated working pressure.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Grinnell or TFP Fig. SF1. 1, 2 in. NPS.
SI-1.0 SI-1.5 SI-2.0 SI-2.5 SI-3.0 SI-3.5 SI-4.0 SI-4.5 SI-5.0 SI-5.5 SI-6.0
3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
1 (0.3) 1.5 (0.46) 2 (0.61) 2.5 (0.76) 3 (0.91) 3.5 (1.1) 4 (1.2) 4.5 (1.4) 5 (1.5) 5.5 (1.7) 6 (1.8)
8.6 (2.6) 9.4 (2.8) 10.2 (3.1) 11.0 (3.3) 11.8 (3.6) 12.0 (3.7) 12.2 (3.7) 12.4 (3.8) 12.6 (3.8) 12.8 (3.8) 12.9 (3.9)
Approval is limited to the vertical down position and with two cables attached to the springs. Approval is limited to the horizontal position and with one cable attached to the spring. The maximum rated working pressure is 175 psi (1205 kPa). These models were tested with a automatic sprinkler with a Nominal Discharge Coefficient of 8.0 gal/min/(psi). The minimum water pressure required to move the piston to the fully extended position is 25 psi (170 kPa). The following automatic sprinklers are FM Approved for use in the models listed above:
SIN Nominal K-Factor Bulb Type Sprinkler Manufacturer
GL8164 VK350
Model
8.0 8.0
NPT in.
3 4 3 4 3 4 3 4 3 4 3 4 3 4
1 (0.3) 1.5 (0.46) 2 (0.61) 2.5 (0.76) 3 (0.91) 3.5 (1.1) 4 (1.2)
9.2 (2.8) 10.1 (3.1) 11.1 (3.4) 12.1 (3.7) 13.1 (3.9) 13.2 (4.0) 13.4 (4.1)
FM Approvals
1-51
Model
NPT in.
3 4 3 4 3 4 3 4
Approval is limited to the vertical down position and with two cables attached to the springs. Approval is limited to the horizontal position and with one cable attached to the spring. The maximum rated working pressure is 175 psi (1205 kPa). These models were tested with an automatic sprinkler with a Nominal Discharge Coefficient of 11.2 gal/min/(psi). The minimum water pressure required to move the piston to the fully extended position is 25 psi (170 kPa). The following automatic sprinklers are FM Approved for use in the models listed above:
SIN Nominal K-Factor Bulb Type Sprinkler Manufacturer
VK530
11.2
Job G5, 5 mm
Model
NPT in.
SI-B-1.0 SI-B-1.5 SI-B-2.0 SI-B-2.5 SI-B-3.0 SI-B-3.5 SI-B-4.0 SI-B-4.5 SI-B-5.0 SI-B-5.5 SI-B-6.0
3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
1 (0.3) 1.5 (0.5) 2 (0.6) 2.5 (0.8) 3 (0.9) 3.5 (1.1) 4 (1.2) 4.5 (1.4) 5 (1.5) 5.5 (1.7) 6 (1.8)
3.7 (1.1) 3.7 (1.1) 3.7 (1.1) 3.7 (1.1) 3.7 (1.1) 4.15 (1.3) 4.6 (1.4) 5.05 (1.5) 5.5 (1.7) 5.95 (1.8) 6.4 (1.9)
Approval is limited to the vertical down position only and with two cables attached to the springs. The maximum rated working pressure is 175 psi (1205 kPa). These models were tested with an automatic sprinkler with a Nominal Discharge Coefficient of 8.0 gal/min/(psi). The minimum water pressure required to move the piston to the fully extended position is 25 psi (170 kPa). The following automatic sprinklers are FM Approved for use in the models listed above:
SIN Nominal K-Factor Bulb Type Sprinkler Manufacturer
GL8164 VK350
Model
8.0 8.0
NPT in.
SI-B-1.0 SI-B-1.5 SI-B-2.0 SI-B-2.5 SI-B-3.0 SI-B-3.5 SI-B-4.0 SI-B-4.5 SI-B-5.0 SI-B-5.5 SI-B-6.0
3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
1 (0.3) 1.5 (0.5) 2 (0.6) 2.5 (0.8) 3 (0.9) 3.5 (1.1) 4 (1.2) 4.5 (1.4) 5 (1.5) 5.5 (1.7) 6 (1.8)
3.3 (1.0) 3.6 (1.1) 3.8 (1.2) 4.1 (1.3) 4.3 (1.4) 4.9 (1.5) 5.4 (1.6) 6.0 (1.8) 6.5 (2.0) 7.1 (2.2) 7.6 (2.3)
FM Approvals
1-52
Approval is limited to the vertical down position only and with two cables attached to the springs. The maximum rated working pressure is 175 psi (1205 kPa). These models were tested with an automatic sprinkler with a Nominal Discharge Coefficient of 11.2 gal/min/(psi). The minimum water pressure required to move the piston to the fully extended position is 25 psi (170 kPa). The following automatic sprinklers are FM Approved for use in the models listed above:
SIN Nominal K-Factor Bulb Type Sprinkler Manufacturer
VK530
11.2
Job G5, 5 mm
1 2 1 2 1 2 1 2
1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by AA Precision Metal Ltd.
Clean-Flex Model Welded Clean-Flex Model Welded Clean-Flex Model Welded Clean-Flex Model Welded
1 2 1 2 1 2 1 2
Clean-Flex Model Welded. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanrooms. Approval is limited for use in cleanroom ceilings manufactured by CLEANPAK International Inc. When properly installed, the collar on the outlet pipe butts up against hold-down bracket on upper surface of ceiling and the sprinkler head frame extends below the ceiling.
Model NPT in. Hose Assembly length ft (m) Equivalent Length of 1 in. Schedule 40 Pipe, ft (m)
1 2 1 2 1 2 1 2
15.4 (4.7) 15.4 (4.7) 15.4 (4.7) 15.4 (4.7) 21.4 (6.5) 21.4 (6.5) 21.4 (6.5) 21.4 (6.5)
1 2 1 2 1 2 1 2
Cleanpak Model WF WCO: 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanrooms. The WCO Series is constructed of extruded seamless vacuum-formed white tube of open-pitch convoluted PTFE, protected by stainless steel braid. Available with and without armor covering. Approval is limited for use in cleanroom ceilings manufactured by CLEANPAK International Inc. WF = Weld Free N = No Armor covering A = Armor covering 50 = Live length in inches between collars. 72 = Live length in inches between collars. C304L/C316L = Stainless Steel alloy for the couplers on the ends of the hose.
FM Approvals
1-53
Flexible sprinkler hose with threaded end fittings are for use in commercial suspended ceilings. The flexible hoses are to be installed according to the manufacturers directives. Unless indicated, the hoses have a rated working pressure of 175 psi (1205 kPa).
Dektronic Enterprise Co Ltd, 8F, No. 155, Sec. 1, Jung Shan Road, Yung He City, Taipei, Hsien Taiwan ROC 83113
NPT in.
1 2
Model
1 2
1 2
1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by United Information Systems Co., Ltd. (T Grid Model TG001 and Cross Joint Model CJ001).
NPT in.
1 2
Model
DK-FLH1001-CTC
4.2 (1.3)
11.5 (3.5)
1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Cherng-Gang Technology Construct Co., Ltd.
NPT in.
1 2
Model
DK-FLH1001-F
4.2 (1.3)
11.5 (3.5)
1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Fuji Electric Co., Ltd.
Model
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
1.6 (0.5) 9.5 (2.9) 13.6 (4.1) 19.2 (5.9) 25.4 (7.7)
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanrooms. Approval is limited for use in cleanrooms manufactured by Shin Sung Engineering Co., Ltd.
Model
CRCS0036
3 (0.9)
15.1 (4.6)
Model CRCS0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model CG6200 manufactured by Channel Systems Inc.
NPT in.
1 2
Model
CRCS0072
6 (1.8)
27.5 (8.4)
Model CRCS0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model CG6200 manufactured by Channel Systems Inc.
FM Approvals
1-54
Model
NPT in.
1 2
CRC 0036
3 (0.9)
15.1 (4.6)
Model CRC 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Clestra Cleanrooms Inc., now owned and manufactured by Gordon Inc.
NPT in.
1 2
Model
CRC 0072
6 (1.8)
27.5 (8.4)
Model CRC 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Clestra Cleanrooms Inc., now owned and manufactured by Gordon Inc.
NPT in.
1 2
Model
CRCAPL-0036
3 (0.9)
15.1 (4.6)
Model CRAPL-0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid manufactured by Kikukawa.
NPT in.
1 2
Model
CRCAPL-0072
6 (1.8)
27.5 (8.5)
Model CRAPL-0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid manufactured by Kikukawa.
NPT in.
1 2
Model
CRCS0036
3 (0.9)
15.1 (4.6)
Model CRCS0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model CG6200 manufactured by Channel Systems Inc.
NPT in.
1 2
Model
CRCS0072
6 (1.8)
27.5 (8.4)
Model CRCS0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model CG6200 manufactured by Channel Systems Inc.
NPT in.
1 2
Model
CRD 0036
3 (0.9)
15.1 (4.6)
Model CRD 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Daw Technologies, Inc.
NPT in.
1 2
Model
CRD 0072
6 (1.8)
28.4 (8.4)
Model CRD 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Daw Technologies, Inc.
FM Approvals
1-55
Model
NPT in.
1 2
CRD 1036
3 (0.9)
15.1 (4.6)
Model CRD 1036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Daw Technologies, Inc.
NPT in.
1 2
Model
CRSBB 0036
3 (0.9)
15.1 (4.6)
Model CRFH-0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid Model No. UG-1, UG-1 Gel, UG-Lite and UG-Lite-Gel manufactured by F. H. Chase Inc..
NPT in.
1 2
Model
CRSBB 0072
6 (1.8)
27.5 (8.4)
Model CRFH 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid Model No. UG-1, UG-1 Gel, UG-Lite and UG-Lite-Gel manufactured by F. H. Chase Inc..
NPT in.
1 2
Model
CRD 1072
6 (1.8)
27.5 (8.4)
Model CRD 1072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Daw Technologies, Inc.
NPT in.
1 2
Model
CRGDS0036
3 (0.9)
15.1 (4.6)
Model CRGDS0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model DS/20 manufactured by Gordon Inc.
NPT in.
1 2
Model
CRGDS0072
6 (1.8)
27.5 (8.4)
Model CRGDS0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model DS/20 manufactured by Gordon Inc.
NPT in.
1 2
Model
CRF20036
3 (0.9)
15.1 (4.6)
Model CRF20036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model F2000D manufactured by Facilities Incorporated.
NPT in.
1 2
Model
CRF20072
6 (1.8)
27.5 (8.4)
Model CRF20072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model F2000D manufactured by Facilities Incorporated.
FM Approvals
1-56
Model
NPT in.
1 2
CRF40036
3 (0.9)
15.1 (4.6)
Model CRF40036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model F4000D manufactured by Facilities Incorporated.
NPT in.
1 2
Model
CRF40072
6 (1.8)
27.5 (8.4)
Model CRF40072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling Model F4000D manufactured by Facilities Incorporated.
NPT in.
1 2
Model
CRG 0036
3 (0.9)
15.1 (4.6)
Model CRG 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Gordon Inc.
NPT in.
1 2
Model
CRG 0072
6 (1.8)
27.5 (8.4)
Model CRG 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Gordon Inc.
NPT in.
1 2
Model
CRGV0036
3 (0.9)
15.1 (4.6)
Model CRGV0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Galvani SRL.
NPT in.
1 2
Model
CRGV0072
6 (1.8)
27.5 (8.4)
Model CRGV0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Galvani SRL.
NPT in.
1 2
Model
CRH 0036
3 (0.9)
15.1 (4.6)
Model CRH 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
CRH 0072
6 (1.8)
28.4 (8.4)
Model CRH 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
FM Approvals
1-57
Model
NPT in.
1 2
CRS 0036
3 (0.9)
15.1 (4.6)
Model CRS 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering.
NPT in.
1 2
Model
CRS 0040
3.3 (1.0)
15.3 (4.7)
Model CRS 0040. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering.
NPT in.
1 2
Model
CRS 0060
5 (1.52)
24 (7.3)
Model CRS 0060. 1 in. nominal dia. flexible sprinkler metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering.
NPT in.
1 2
Model
CRS 0072
6 (1.8)
27.5 (8.4)
Model CRS 0072. 1 in. nominal dia. flexible sprinkler metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering.
NPT in.
1 2
Model
CRSBB 0036
3 (0.9)
15.1 (4.6)
Model CRSBB-0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid Model No. 2035 manufactured by SBB Inc.
NPT in.
1 2
Model
CRSBB 0072
6 (1.8)
27.5 (8.4)
Model CRSBB 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid Model No. 2035 manufactured by SBB Inc.
NPT in.
1 2
Model
CRW 0036
3 (0.9)
15.1 (4.6)
Model CRW 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by M+W Zander (formerly Meissner & Wurst).
NPT in.
1 2
Model
CRW 0072
6 (1.8)
28.4 (8.4)
Model CRW 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by M+W Zander (formerly Meissner & Wurst).
FM Approvals
1-58
Model
NPT in.
1 2
CRYCF 0036
3 (0.9)
15.1 (4.6)
Model CRYCF 0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Yung Cheng Feng.
NPT in.
1 2
Model
CRYCF 0072
6 (1.8)
27.5 (8.4)
Model CRYCF 0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Yung Cheng Feng.
NPT in.
1 2
Model
CRH0036-PTFE
3 (0.9)
10.4 (3.4)
Model CRH0036-PTFE. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly utilizes a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
CRH0072-PTFE
6 (1.8)
15.1 (4.6)
Model CRH0072-PTFE. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly utilizes a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
CRH0036-PTFE-A
3 (0.9)
10.4 (3.4)
Model CRH0036-PTFE-A. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
CRH0072-PTFE-A
6 (1.8)
15.1 (4.6)
Model CRH0072-PTFE-A. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
CRW0036-PTFE-A
3 (0.9)
10.4 (3.4)
Model CRW0036-PTFE-A. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceiling grid manufactured by M&W.
NPT in.
1 2
Model
CRW0072-PTFE-A
6 (1.8)
15.1 (4.6)
FM Approvals
1-59
Model CRW0072-PTFE-A. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. Approval is limited for use in cleanroom ceiling grid manufactured by M&W.
NPT in.
1 2
Model
CRGLRP-0036
3 (0.9)
15.1 (4.6)
Model CRGLRP-0036. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid P/N LRPSCSTROUGH manufactured by Gordon.
NPT in.
1 2
Model
CRGLRP-0072
6 (1.8)
27.5 (8.5)
Model CRGLRP-0072. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceiling grid P/N LRPSCSTROUGH manufactured by Gordon.
Model
GRA0141
6 (1.8)
23.5 (7.2)
Model GRA0141 DROP NIPPLE ASSEMBLY. 1 in. nominal dia flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
Model
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
1.6 (0.5) 9.5 (2.9) 13.6 (4.1) 19.2 (5.9) 25.4 (7.7)
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanrooms. Approval is limited for use in cleanrooms manufactured by Shin Sung Engineering Co., Ltd.
Panew Company Limited, 8F-5, No. 2 Jianba Road, Chung Ho, Taipei Hsien, Taiwan ROC
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9700 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by AA Precision Metal Ltd.
FM Approvals
1-60
Model
NPT in.
1 2
1 2
1 2
1 2
Model P-9710 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Topline Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9720 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Fuji Electric Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9730 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Yung Cheng Feng Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9740 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by United Information Systems Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
FM Approvals
1-61
Model P-9750 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Topwell Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9760 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by M+W Zander Facility Engineering GmbH.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9770 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Tenryo Technology and Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9790 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Tien Hann Engineering Co., Ltd.
Paradise Industry Co Ltd, 65-2 Chooneui-Dong, Woonmi-Ku, Bucheon-City Kyunggi-Do, Korea (420-120)
NPT in.
1 2
Model
4.5 (1.4) 6.1 (1.8) 7.2 (2.2) 4.5 (1.4) 6.1 (1.8) 3.3 (1.0) 8.5 (2.6) 3.3 (1.0) 8.5 (2.6)
14.4 (4.4) 16.7 (5.1) 23.3 (7.1) 14.4 (4.4) 16.7 (5.1) 13.1 (4.2) 28.2 (8.6) 13.7 (4.2) 36.8 (11.2)
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
FM Approvals
1-62
Model
NPT in.
1 2
3.3 (1.0) 8.5 (2.6) 3.3 (1.0) 8.5 (2.6) 3.3 (1.0) 8.5 (2.6)
13.7 (4.2) 36.8 (11.2) 13.7 (4.2) 31.1 (9.5) 13.7 (4.2) 36.8 (11.2)
1 2
1 2
1 2
1 2
1 2
Models: SFT-1000 and SFT-1500-1. 1 in. nominal dia. flexible metal sprinkler hose with fittings for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is in the range of 4.5 ft (1400 mm) through 6.1 ft (1800 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co., Ltd. and Songhwa Engineering. Model SFT-1500. 1 in. nominal dia. flexible metal sprinkler hose with fittings for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co., Ltd. and Songhwa Engineering. Models: SFT-D, SFT-E, SFT-F, SFT-L and SFT-M. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is in the range of 3.3 ft (1000 mm) through 8.5 ft (2600 mm). Approval is limited for use in cleanroom ceilings manufactured by Hankook E&C, LG Engineering and Construct Corp., Shin Sung Engineering Co., Ltd. and Songhwa Engineering.
Seung Jin Industry Co Ltd, 612, 5 Bar Shi-Wha Industrial Complex, 685-11 Sunggog-Dong, Ansan-Si Kyunggi-Do, 429-450 Korea
NPT in.
1 2
Model
1 2
3 4
3 4
CR: Cleanroom
XX: 12 for 12 in. reducer and 34 for 34 in. reducer. YY: Length of Hose assembly. (08 is a 0.8 m (2.6 ft) long hose assembly and 26 is a 2.6 m (8.5 ft) long hose assembly. 08 through 26 for 12 in. reducer, and 10 through 25 for 34 in. reducer. ZZZZ: Year and month manufactured.
Approval of this 1 in. nominal dia. flexible metal hose is limited for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in a cleanroom ceiling Model S-139 manufactured by Shin Sung Engineering Co., Ltd.
NPT in.
1 2
Model
SJ-CR-01 SJ-CR-01
3 4
Model SJ-CR-01. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval of 3.3 ft (1.0 m). Approval is limited for use in cleanroom ceiling Model S-139 manufactured by Shinsung Engineering Co., Ltd.
NPT in.
1 2
Model
SJ-CR-02 SJ-CR-02
6 (1.8) 6 (1.8)
3 4
FM Approvals
1-63
Model SJ-CR-02. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval of 6 ft (1.8 m). Approval is limited for use in cleanroom ceiling Model S-139 manufactured by Shinsung Engineering Co., Ltd.
NPT in.
1 2
Model
SJ-CR-03 SJ-CR-03
3 4
Model SJ-CR-03. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval of 8.3 ft (2.5 m). Approval is limited for use in cleanroom ceiling Model S-139 manufactured by Shinsung Engineering Co., Ltd.
NPT in.
1 2
Model
SJ-CR-08 SJ-CR-25
1 2
Model SJ-CR-08 through SJ-CR-25. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in a cleanroom ceiling Model S-139 manufactured by Shin Sung Engineering Co., Ltd. Approval of these models is in the range as stated above. 08 to 25 is the range of length, 0.8 m to 2.5 m (2.6 ft to 8.2 ft).
Shanghai Genius Technical Corp Ltd, No. 7166 Zhong Chun Road, Qibao Town, Minhang District, Shanghai, P.R. China 201101
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9700. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by AA Precision Metal Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9710. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Topline Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9720. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Fuji Electric Co., Ltd.
FM Approvals
1-64
Model
NPT in.
1 2
1 2
1 2
1 2
Model P-9730. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Yung Cheng Feng Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9740. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by United Information Systems Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9750. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Topwell Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9760. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by M+W Zander Facility Engineering GmbH.
NPT in.
1 2
Model
1 2
1 2
1 2
FM Approvals
1-65
Model P-9770. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Tenryo Technology and Engineering Co., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9790. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in cleanroom ceilings manufactured by Tien Hann Engineering Co., Ltd.
Super Flex Enterprises Co Ltd, No. 16, Lane 561, Sec 2, Kouji Rd, Taoyuan City, Taoyuan, Taiwan ROC
NPT in.
1 2
Model
SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L SP-L
1.9 (0.60) 2.1 (0.64) 2.6 (0.80) 3.1 (0.96) 3.3 (1.0) 3.5 (1.0) 3.8 (1.2) 3.9 (1.2) 4.4 (1.3) 5.2 (1.6) 6.9 (2.1) 7.8 (2.4) 8.4 (2.6)
12.5 (3.8) 12.7 (3.9) 13.1 (4.0) 15.8 (4.8) 16.4 (5.0) 17.4 (5.3) 19.0 (5.8) 19.7 (6.0) 21.9 (6.7) 28.8 (8.8) 17.8 (5.4) 18.2 (5.5) 18.5 (5.6)
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
Model SP-L. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in the following cleanroom ceilings: AA Precision Metal Ltd. ACC Tech Materials Co., Ltd. Fuji Electric Systems L&K Engineering Co., Ltd Long Long Clean Room Technology Co., Ltd. M+W Zander North Enging Corp.-Howell Tenryo Technology & Engineering Co., Ltd. Topline System Engineering Co., Ltd. Tien Hann Engineering Co., Ltd. Topwell Engineering Co., Ltd. United Information Systems Co., Ltd. Yung Cheng Feng Engineering Co., Ltd
NPT in.
1 2
Model
SP-L-1
1.9 (0.60)
12.5 (3.8)
FM Approvals
1-66
Model
NPT in.
1 2
SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1 SP-L-1
2.1 (0.64) 2.6 (0.80) 3.1 (0.96) 3.3 (1.0) 3.5 (1.0) 3.8 (1.2) 3.9 (1.2) 4.4 (1.3) 5.2 (1.6) 6.9 (2.1) 7.8 (2.4) 8.4 (2.6)
12.7 (3.9) 13.1 (4.0) 15.8 (4.8) 16.4 (5.0) 17.4 (5.3) 19.0 (5.8) 19.7 (6.0) 21.9 (6.7) 28.8 (8.8) 17.8 (5.4) 18.2 (5.5) 18.5 (5.6)
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
Model SP-L-1. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is limited for use in the following cleanroom ceilings: AA Precision Metal Ltd. ACC Tech Materials Co., Ltd. Fuji Electric Systems L&K Engineering Co., Ltd Long Long Clean Room Technology Co., Ltd. M+W Zander North Enging Corp.-Howell Tenryo Technology & Engineering Co., Ltd. Topline System Engineering Co., Ltd. Tien Hann Engineering Co., Ltd. Topwell Engineering Co., Ltd. United Information Systems Co., Ltd. Yung Cheng Feng Engineering Co., Ltd
Model
SF56016TFWC000
5 (1.5)
22.4 (6.8)
Model SF56016TFWC000. 1 in. nominal dia. flexible sprinkler hose for connection to automatic sprinklers in cleanrooms. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. (polytetrafluoroethylene) PTFE convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
NPT in.
1 2
Model
SF56016TFWC001
6 (1.8)
29.9 (9.1)
Model SF56016TFWC001. 1 in. nominal dia. flexible sprinkler hose for connection to automatic sprinklers in cleanrooms. This hose assembly has an armor protective covering over a stainless steel braid over a nominal 1 in. I.D. (polytetrafluoroethylene) PTFE convoluted hose. Approval is limited for use in cleanroom ceilings manufactured by HUNTAIR.
FM Approvals
1-67
Model
T1S025
3.3 (1.0)
14.2 (4.2)
Model T1S025. 1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in cleanroom ceilings. This hose assembly has a stainless steel braid over a nominal 1 in. I.D. (polytetrafluoroethylene) PTFE hose. Approval is limited for use in cleanroom ceilings manufactured by M+W Zander Type 55/70-T/E Profile.
Model
HYDRA HYDRA
1 2
HYDRA Hose. 1 in. (25 mm) nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Approval is in the range of 3.3 ft to 7.7 ft (1000 mm to 2000 mm). Approval is limited for use in cleanroom ceilings manufactured by the following companies:
Company M & W Zander Facility Eng. GmbH M & W Zander Facility Eng. GmbH Daldrop & Dr. Ing Huber GmbH + Co. Grid Style M & W Profile Type Grid 55/60-FL/E M & W Profile Type Grid 55/70-T/E 40N
Yong Won E.N.C. Ltd, 116-1 Sedgu-Ri, Kwangjeuk-Myun, Yangju-Gun Keungki-Do, Korea
NPT in.
1 2
Model
YB25-I YB25-I
1 2
Model YB25-I. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB25-I is a one piece style. The reducer and nipple are welded to the flexible hose.
NPT in.
1 2
Model
YB25-II YB25-II
1 2
Model YB25-II. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB25-II is a three piece style. The reducer and nipple are connected to the flexible hose using as a nut.
NPT in.
1 2
Model
YB25-III YB25-III
1 2
Model YB25-III. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB25-III is a two piece style. The reducer is welded to the flexible hose and nipple is connected to the flexible hose using a nut.
FM Approvals
1-68
Model
NPT in.
1 2
YB28-IA YB28-IA
1 2
Model YB28-lA. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB28-IA is a one piece style. The reducer and nipple are welded to the flexible hose.
NPT in.
1 2
Model
YB28-I YB28-I
1 2
Model YB28-l. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB28-I is a one piece style. The reducer and nipple are welded to the flexible hose.
NPT in.
1 2
Model
YB28-II YB28-II
1 2
Model YB28-II. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB28-II is a three piece style. The reducer and nipple are connected to the flexible hose using as a nut.
NPT in.
1 2
Model
YB28-III YB28-III
1 2
Model YB28-III. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in cleanroom ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). Approval is limited for use in cleanroom ceilings manufactured by Shin Sung Engineering Co. Ltd. The Model YB28-III is a two piece style. The reducer is welded to the flexible hose and nipple is connected to the flexible hose using a nut.
Model
1 2
1 2
The 1 in. nominal diameter flexible sprinkler hose Model IL001 is Approved for providing a connection to automatic sprinkler protection to the interior of Fiberglass Reinforced Plastic (FRP) ducts and is not FM Approved for use in other applications. Approval is limited to using GS27 resin as the bonding agent between the bottom mounting block and the FRP duct.
FM Approvals
1-69
Model
NPT in.
1 2
1 2
1 2
The 1 in. nominal diameter flexible sprinkler hose Model IL001 is Approved for providing a connection to automatic sprinkler protection to the interior of steel ducts and is not FM Approved for use in other applications. Approval is limited to using GS27 resin as the bonding agent between the bottom mounting block and the steel duct.
NPT in.
1 2
Model
1 2
1 2
The 1 in. nominal diameter flexible sprinkler hose Model IL001 is Approved for providing a connection to automatic sprinkler protection to the interior of polypropylene plastic ducts and is not FM Approved for use in other applications. Approval is limited to using GS27 resin as the bonding agent between the bottom mounting block and the polypropylene plastic duct.
Model
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
8.7 (2.6) 16.7 (5.1) 22.5 (6.9) 28.3 (8.6) 34.5 (10.5)
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in ducts. Approval is limited for use in circular flange metal ducts.
EFDS-01A EFDS-02A EFDS-03A EFDS-04A EFDS-05A
1 2
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
8.7 (2.6) 16.7 (5.1) 22.5 (6.9) 28.3 (8.6) 34.5 (10.5)
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in ducts. Approval is limited for use in square flange metal ducts.
Model
1024 1036
2 (0.6) 3 (.9)
11 (3.6) 19 (5.8)
1 2
FM Approvals
1-70
Model
NPT in.
1 2
1048
4 (1.2)
21 (6.4)
Approval of the Model 1000 series is limited to use in providing sprinkler protection to the interior of Fiberglass Reinforced Plastic (FRP) ducts and is not FM Approved for use in ducts of other materials or for other applications. Approval is limited to using Derakane 510 resin as the bonding agent between the bottom mounting block and the FRP duct.
NPT in.
1 2
Model
1 2
1 2
Approval of the Model 1100 series is limited to use in providing sprinkler protection to the interior of metal ducts and is not FM Approved for use in ducts of other materials or for other applications.
NPT in.
1 2
Model
1 2
1 2
Approval of the Model 1200 series is limited to use in providing sprinkler protection to the interior of polypropylene plastic ducts and is not FM Approved for use in ducts of other materials or for other applications.
NPT in.
1 2
Model
1 2
1 2
Approval of the Model 1300 series is limited to use in providing sprinkler protection to the interior of polyvinyl chloride (PVC) plastic ducts and is not FM Approved for use in ducts of other materials or for other applications.
Model
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
8.7 (2.6) 16.7 (5.1) 22.5 (6.9) 28.3 (8.6) 34.5 (10.5)
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in ducts. Approval is limited for use in circular flange metal ducts.
KFB-SPDS-01A
1 2
2.5 (750)
8.7 (2.6)
FM Approvals
1-71
Model
NPT in.
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in ducts. Approval is limited for use in square flange metal ducts.
Panew Company Limited, 8F-5, No. 2 Jianba Road, Chung Ho, Taipei Hsien, Taiwan ROC
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9900 Approval is limited to use in providing sprinkler protection to the interior of Fiberglass Reinforced Plastic (FRP) ducts, Polypropylene plastic ducts and metal ducts and is not FM Approved for use in ducts of other materials or for other applications.
Paradise Industry Co Ltd, 65-2 Chooneui-Dong, Woonmi-Ku, Bucheon-City Kyunggi-Do, Korea (420-120)
NPT in.
1 2
Model
1 2
1 2
1 2
1 in. nominal dia. flexible sprinkler hose with fittings for providing a connection to automatic sprinklers in ducts. Approval is in the range of 3.3 ft (1000 mm) to 8.5 ft (2600 mm).
Seung Jin Industry Co Ltd, 612, 5 Bar Shi-Wha Industrial Complex, 685-11 Sunggog-Dong, Ansan-Si Kyunggi-Do, 429-450 Korea
NPT in.
1 2
Model
1 2
3 4
3 4
DU: Duct XX: Product length. 08 through 26 (08 is a 0.8 m (2.6 ft) long hose assembly and 26 is a 2.6 m (8.5 ft) long hose assembly. YYYY: Year and month manufactured.
Approval of these 1 in. nominal dia. flexible metal sprinkler hose model is limited to use in providing sprinkler protection to the interior of Fiberglass Reinforced Plastic (FRP) ducts and is not Approved for use in ducts of other materials or for other applications.
FM Approvals
1-72
Shanghai Genius Technical Corp Ltd, No. 7166 Zhong Chun Road, Qibao Town, Minhang District, Shanghai, P.R. China 201101
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9900. Approval is limited to use in providing sprinkler protection to the interior of Fiberglass Reinforced Plastic (FRP) ducts, Polypropylene plastic ducts and metal ducts and is not FM Approved for use in ducts of other materials or for other applications.
Yong Won E.N.C. Ltd, 116-1 Sedgu-Ri, Kwangjeuk-Myun, Yangju-Gun Keungki-Do, Korea
NPT in.
1 2
Model
3.5 (1.07) 8.4 (2.57) 3.5 (1.07) 8.4 (2.57) 3.5 (1.07) 8.4 (2.57) 3.5 (1.07) 8.4 (2.57)
5.5 (1.6) 15.2 (4.6) 5.7 (1.7) 17.0 (5.2) 5.5 (1.6) 15.2 (4.6) 5.7 (1.7) 17.0 (5.2)
1 2
3 4
3 4
1 2
1 2
3 4
3 4
Model YB28-D-BP 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in ducts. Available in a range from (3.5 to 8.4 feet) 1075 mm to 2575 mm. Approval is limited to interior sprinkler protection of Polypropylene Plastic ducts of 10 to 60 in. (25.4 to 152.4 cm) diameter and is not Approved for use in ducts of other materials or for other applications. The Model YB28-D-BP is a one piece hose with nuts on each end. A threaded nipple is connected to the nut at the inlet of the hose. Approval is limited to interior sprinkler protection of Fiberglass Reinforced Plastic (FRP) ducts of 10 to 60 in. (25.4 to 152.4 cm) diameter and is not Approved for use in ducts of other materials or for other applications. Approval is limited to using FRP bond made by Korea Chemical Company as the bonding agent between the bottom mounting block and the FRP duct.
Model
1 2
1 2
1 2
FM Approvals
1-73
Model
NPT in.
1 2
1 2
1 2
1 2
18.9 (5.7) 26.5 (8.1) 31.9 (9.7) 44.3 (13.5) 55.5 (16.9) 61.5 (18.7) 59.9 (18.3)
1 2
1 2
1 2
1 2
1 2
1 2
3 4
18.2 (5.5) 26.0 (7.9) 31.6 (9.6) 40.3 (12.3) 54.1 (16.5) 60.1 (18.3) 59.5 (18.1)
3 4
3 4
3 4
3 4
3 4
3 4
3 4
18.2 (5.5) 26.0 (7.9) 31.6 (9.6) 40.3 (12.3) 54.1 (16.5) 60.1 (18.3) 59.5 (18.1)
3 4
3 4
3 4
3 4
3 4
3 4
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by AF-USA LLC. The code of information for these model designations is as follows:
Marking Description
AF B W
Manufacturers initials Braid Welded: These model hoses have a weld on the outlet end, securing the outlet reducer to the hose. A slip nut connects the flexible hose to the inlet nipple.
FM Approvals
1-74
Marking
Description
Flexible Hose Lengths: 24 31 36 48 60 72 84 H T 24 in. 31 in. 36 in. 48 in. 60 in. 72 in. 84 in.
1 2 3 4
Dong-A Flexible Metal Tubes Co Ltd, 5th Floor, Yuchang B/D, #108-6, Yangjae Dong, Seocho-Gu, Seoul, Korea (137-130)
NPT in.
1 2
Model
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
1 2
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
1 2
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
3 4
20.7 (6.3) 32.1 (9.8) 48.4 (14.7) 56.6 (17.2) 77.1 (23.5)
3 4
3 4
3 4
3 4
FM Approvals
1-75
Model
NPT in.
3 4
20.7 (6.3) 32.1 (9.8) 48.4 (14.7) 56.6 (17.2) 77.1 (23.5)
3 4
3 4
3 4
3 4
3 4
20.7 (6.3) 32.1 (9.8) 48.4 (14.7) 56.6 (17.2) 77.1 (23.5)
3 4
3 4
3 4
3 4
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by Dong-A Flexible Metal Tubes Co., Ltd. The code of information for these model designations is as follows:
Marking Description
Manufacturers initials The hose is threaded to a nipple on the inlet end and threaded to a reducer at the outlet. The hose is threaded to a nipple on the inlet end and the reducer is brazed to the flexible hose at the outlet The hose is brazed to a nipple on the inlet end and brazed to a reducer at the outlet Flexible Hose Lengths: 01 = 780 mm 02 = 1,220 mm 03 = 1,540 mm 04 = 1,880 mm 05 = 2,500 mm
12 34
Model
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
8.7 (2.6) 16.7 (5.1) 22.5 (6.9) 28.3 (8.6) 34.5 (10.5)
1 2
1 2
1 2
1 2
EFB331
3 4
2.5 (750)
7.2 (2.2)
FM Approvals
1-76
Model
NPT in.
3 4
3 4
3 4
3 4
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by Easyflex Inc.
Model
3.5 (1.1) 4.8 (1.5) 6.8 (2.1) 8.5 (2.6) 8.9 (2.7)
1 2
1 2
1 2
1 2
This is a standard flexible hose with a pressure rating of 175 psi (1205 kPa). Approval on these models of flexible metal sprinkler hose is limited for use in commercial suspended ceilings (T-Bar Grid) and Sheetrock suspended ceilings, with a ceiling bracket system manufactured by FlexHead Industries Inc. The FlexHead brackets are identified as follows: Part Numbers: SP-24-BKT (1) SP-24-BKT (2) MP-24-BKT MP-24-BKT-2 SP-06TZ-BKT AD-16-BKT-2 AD-24-BKT-2 UH-2
SP = Single Port MP = Multiport TZ = Tech Zone AD = Adjustable UH = Universal Hub (1) = 1 Piece (2) = 2 Piece 06 = Length in inches of bracket 16 = Length in inches of bracket 24 = Length in inches of bracket BKT = Bracket
The FlexHead Clamp Model UH-2 with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod is for attachment to support these hose models. The Model UH-2 FlexHead clamp is manufactured by FlexHead Industries Inc.
NPT in.
1 2
Model
1 2
1 2
1 2
1 2
FM Approvals
1-77
The H indicates a high pressure of 300 psi (2070 kPa). Approval of this flexible metal sprinkler hose is limited for use in commercial suspended ceilings, (T-Bar Grid) and Sheetrock suspended ceilings with a ceiling bracket system manufactured by FlexHead Industries Inc. The FlexHead brackets are identified as follows: Part Numbers: SP-24-BKT (1) SP-24-BKT (2) MP-24-BKT MP-24-BKT-2 SP-06TZ-BKT AD-16-BKT-2 AD-24-BKT-2 UH-2
SP = Single Port MP = Multiport TZ = Tech Zone AD = Adjustable UH = Universal Hub (1) = 1 Piece (2) = 2 Piece 06 = Length in inches of bracket 16 = Length in inches of bracket 24 = Length in inches of bracket BKT = Bracket
The FlexHead Clamp Model UH-2 with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod is for attachment to support these hose models. The Model UH-2 FlexHead clamp is manufactured by FlexHead Industries Inc.
NPT in.
1 2
Model
2.9 (0.9) 4.4 (1.3) 6.7 (2.0) 10.4 (3.4) 11.4 (3.5)
1 2
1 2
1 2
1 2
The M indicates a mechanical flare type connection with a pressure rating of 300 psi (2070 kPa). Approval of this flexible metal sprinkler hose is limited for use in commercial suspended ceilings, with a ceiling bracket system manufactured by FlexHead Industries Inc. The FlexHead brackets are identified as follows: Part Numbers: SP-24-BKT (1) SP-24-BKT (2) MP-24-BKT MP-24-BKT-2 SP-06TZ-BKT AD-16-BKT-2 AD-24-BKT-2 UH-2
SP = Single Port MP = Multiport TZ = Tech Zone AD = Adjustable UH = Universal Hub (1) = 1 Piece (2) = 2 Piece 06 = Length in inches of bracket 16 = Length in inches of bracket 24 = Length in inches of bracket BKT = Bracket
The FlexHead Clamp Model UH-2 with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod is for attachment to support these hose models. The Model UH-2 FlexHead clamp is manufactured by FlexHead Industries Inc.
NPT in.
1 2
Model
5.5 (1.7) 6.8 (2.1) 8.8 (2.7) 10.5 (3.2) 10.9 (3.3)
1 2
1 2
1 2
1 2
The E indicates an elbow welded on the end of the hose. Approval of these models of flexible metal sprinkler hose incorporate a stainless steel elbow welded on the outlet end of the hose and are limited for use in commercial suspended ceilings (T-Bar Grid) and Sheetrock suspended ceilings, with a ceiling bracket system manufactured by FlexHead Industries Inc. The FlexHead brackets are identified as follows:
FM Approvals
1-78
Part Numbers: SP-24-BKT (1) SP-24-BKT (2) MP-24-BKT MP-24-BKT-2 SP-06TZ-BKT AD-16-BKT-2 AD-24-BKT-2 UH-2
SP = Single Port MP = Multiport TZ = Tech Zone AD = Adjustable UH = Universal Hub (1) = 1 Piece (2) = 2 Piece 06 = Length in inches of bracket 16 = Length in inches of bracket 24 = Length in inches of bracket BKT = Bracket
The FlexHead Clamp Model UH-2 with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod is for attachment to support these hose models. The Model UH-2 FlexHead clamp is manufactured by FlexHead Industries Inc.
NPT in.
1 2
Model
5.5 (1.7) 6.8 (2.1) 8.8 (2.7) 10.5 (3.2) 10.9 (3.3)
1 2
1 2
1 2
1 2
3 4
7.8 (2.4) 8.1 (2.5) 17.9 (5.4) 19.9 (6.1) 24.3 (7.4)
3 4
3 4
3 4
3 4
The E-LP indicates a low profile elbow unit welded on the end of the hose. Approval of these models of flexible metal sprinkler hose incorporates a stainless steel elbow welded on the outlet end of the hose and with unistrut channel and pipe clamp is limited to securing these models to the building structure. These models are for use in commercial suspended ceilings (T-Bar Grid) and Sheetrock suspended ceilings with very limited room between floors.
NPT in.
1 2
Model
2036-E-PTFE
3 (0.9)
10.4 (3.4)
Model 2036-E-PTFE. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings (T-Bar Grid) and Sheetrock suspended ceilings. This assembly utilizes a stainless steel braid over a nominal 1 in. I.D. PTFE (polytetrafluoroethylene) convoluted hose. The E indicates an elbow attached on the end of the hose. This hose model is for use with the Model UH-2 (Universal Hub) FlexHead clamp with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod.
NPT in.
3 4
Model
7.8 (2.4) 8.1 (2.5) 17.9 (5.4) 19.9 (6.1) 24.3 (7.4)
3 4
3 4
3 4
3 4
FM Approvals
1-79
This is a standard hose with a pressure rating of 175 psi (1205 kPa). The 75 indicates a 34 inch NPT outlet. Approval on these models of flexible metal sprinkler hose is limited for use in commercial suspended ceilings (T-Bar Grid) and Sheetrock suspended ceilings, with a ceiling bracket system manufactured by FlexHead Industries Inc. The FlexHead brackets are identified as follows: Part Numbers: SP-24-BKT (1) SP-24-BKT (2) MP-24-BKT MP-24-BKT-2 SP-06TZ-BKT AD-16-BKT-2 AD-24-BKT-2 UH-2
SP = Single Port MP = Multiport TZ = Tech Zone AD = Adjustable UH = Universal Hub (1) = 1 Piece (2) = 2 Piece 06 = Length in inches of bracket 16 = Length in inches of bracket 24 = Length in inches of bracket BKT = Bracket
The FlexHead Clamp Model UH-2 with a maximum 2 ft (610 mm) 38 in. nominal size threaded rod is for attachment to support these hose models. The Model UH-2 FlexHead clamp is manufactured by FlexHead Industries Inc.
Model
2.0 (610) 2.6 (790) 3.0 (915) 4.0 (1220) 5.0 (1525) 5.6 (1700) 6.0 (1830) 7.2 (2200) 8.5 (2600) 2.0 (610) 2.6 (790) 3.0 (915) 4.0 (1220) 5.0 (1525) 5.6 (1700) 6.0 (1830) 7.2 (2200) 8.5 (2600)
6.8 (2.1) 8.7 (2.6) 11.5 (3.5) 16.7 (5.1) 20.6 (6.3) 22.5 (6.9) 24.0 (7.3) 28.3 (8.6) 34.5 (10.5) 4.7 (1.4) 7.2 (2.2) 10.6 (3.2) 12.7 (3.9) 17.0 (5.2) 18.8 (5.7) 19.8 (6.0) 22.9 (6.9) 33.4 (10.2)
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
3 4
3 4
3 4
3 4
3 4
3 4
3 4
3 4
3 4
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with the following bracket systems manufactured by Kofulso Co., Ltd. GSB with SSB. TBS with SSB. TBS with SBB. TBL with SSB. TBL with SBB. Stock Bar and clamp assembly in a T-Bar ceiling grid. SHB System and a GSB Bracket assembly in a T-Bar ceiling grid.
FM Approvals
1-80
The description of the bracket systems are as follows: GSB: Grid Snap Bracket - Length of GSB: 24 in. (610 mm) SSB: Snap Clamp Center Bracket SBB: Bolt Clamp Center Bracket TBS: T-Bar Bracket Short TBL: T-Bar Bracket Long Length of Stock Bar: 25 in. (635 mm) SHB: Center Bracket Hook Clamp
NPT in.
1 2
Model
2.0 (610) 2.6 (790) 3.0 (915) 4.0 (1220) 5.0 (1525) 5.6 (1700) 6.0 (1830) 7.2 (2200) 8.5 (2600)
18.0 (5.5) 20.6 (6.3) 22.3 (6.8) 26.7 (8.1) 20.6 (6.3) 32.9 (10.0) 26.3 (8.0) 33.6 (10.2) 41.0 (12.5)
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
2.0 (610) 2.6 (790) 3.0 (915) 4.0 (1220) 5.0 (1525) 5.6 (1700) 6.0 (1830) 7.2 (2200) 8.5 (2600)
16.2 (4.9) 19.4 (5.9) 21.6 (6.6) 27.1 (8.3) 22.5 (6.8) 33.8 (10.3) 26.1 (7.9) 33.3 (10.1) 41.7 (12.7)
GSB with SSB. TBS with SSB. TBS with SBB. TBL with SSB. TBL with SBB. Stock Bar and clamp assembly in a T-Bar ceiling grid. SHB System and a GSB Bracket assembly in a T-Bar ceiling grid.
The description of the bracket systems are as follows: GSB: Grid Snap Bracket Length of GSB: 24 in. (610 mm) SSB: Snap Clamp Center Bracket SBB: Bolt Clamp Center Bracket TBS: T-Bar Bracket Short TBL: T-Bar Bracket Long Length of Stock Bar: 25 in. (635 mm) SHB: Center Bracket Hook Clamp
FM Approvals
1-81
KFBL224
KF: Kofulso (Manufacturers initials) B: Braided hose L: Elbow 2: 12 in. NPT 24: Flexible Hose Length in inches
KFB3102
KF: Kofulso (Manufacturers initials) B: Braided hose 3: 34 in. NPT 102: Flexible hose length in inches
Model
NPT in.
1 2
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
8.7 (2.6) 16.7 (5.1) 22.5 (6.9) 28.3 (8.6) 34.5 (10.5)
1 2
1 2
1 2
1 2
3 4
2.5 (750) 3.9 (1200) 5.6 (1700) 7.2 (2200) 8.5 (2600)
7.2 (2.2) 12.7 (3.9) 18.8 (5.7) 22.9 (6.9) 33.4 (10.2)
3 4
3 4
3 4
3 4
Model
Description
KFB-SP-01A or KFB-SP-01AB
B: Braided hose SP: Flexible 01 in. = 02 in. = 03 in. = 04 in. = 05 in. = Hose Lengths: 2.5 ft (750 mm) 3.9 ft (1200 mm) 5.6 ft (1700 mm) 7.2 ft (2200 mm) 8.5 ft (2600 mm)
Panew Company Limited, 8F-5, No. 2 Jianba Road, Chung Ho, Taipei Hsien, Taiwan ROC
NPT in.
1 2
Model
1 2
1 2
FM Approvals
1-82
Model
NPT in.
1 2
P-9100
7 (2.13)
20.4 (6.2)
Model P-9100. 1 in. nominal dia. Two piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter is threaded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Panew Company Limited.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9120. 1 in. nominal dia. One piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and nipple is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Panew Company Limited.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9200. 1 in. nominal dia. One piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and nipple is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Panew Company Limited.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9210. 1 in. nominal dia. One piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and coupling/threaded fitting is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Panew Company Limited.
NPT in.
1 2
Model
1 2
1 2
1 2
FM Approvals
1-83
Model P-9211. 1 in. nominal dia. One piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and coupling/threaded fitting is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Panew Company Limited.
Paradise Industry Co Ltd, 65-2 Chooneui-Dong, Woonmi-Ku, Bucheon-City Kyunggi-Do, Korea (420-120)
Model SFT-A. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is in the range of 3.3 ft (1000 mm) to 8.4 ft (2550 mm), and is limited for use in commercial suspended ceilings. Model SFT-C. 1 in. nominal dia. flexible sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is in the range of 3.3 ft (1000 mm) to 8.1 ft (2470 mm), and is limited for use in commercial suspended ceilings.
NPT in.
1 2
Model
1 2
1 2
1 2
Approval is limited for use in commercial suspended ceilings, with a ceiling bracket system manufactured by Paradise Industry Co., Ltd.
Rapidrop Limited, Rutland Business Park, Newark Road, Peterborough PE1 5WA, United Kingdom
NPT in.
1 2
Model
Rapidrop -SPB-01A-NPT Rapidrop -SPB-02A-NPT Rapidrop -SPB-03A-NPT Rapidrop -SPB-04A-NPT Rapidrop -SPB-05A-NPT
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
Rapidrop -SPNB-01A-NPT Rapidrop -SPNB-02A-NPT Rapidrop -SPNB-03A-NPT Rapidrop -SPNB-04A-NPT Rapidrop -SPNB-05A-NPT
1 2
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
Rapidrop -SPWB-01A-NPT Rapidrop -SPWB-02A-NPT Rapidrop -SPWB-03A-NPT Rapidrop -SPWB-04A-NPT Rapidrop -SPWB-05A-NPT
1 2
14.6 (4.5) 28.0 (8.5) 50.2 (15.3) 53.5 (16.3) 67.1 (20.4)
1 2
1 2
1 2
1 2
3 4
3 4
3 4
FM Approvals
1-84
Model
NPT in.
3 4
3 4
Rapidrop -SPNB-01B-NPT Rapidrop -SPNB-02B-NPT Rapidrop -SPNB-03B-NPT Rapidrop -SPNB-04B-NPT Rapidrop -SPNB-05B-NPT
3 4
20.7 (6.3) 32.1 (9.8) 48.4 (14.7) 56.6 (17.2) 77.1 (23.5)
3 4
3 4
3 4
3 4
Rapidrop -SPWB-01B-NPT Rapidrop -SPWB-02B-NPT Rapidrop -SPWB-03B-NPT Rapidrop -SPWB-04B-NPT Rapidrop -SPWB-05B-NPT
3 4
20.7 (6.3) 32.1 (9.8) 48.4 (14.7) 56.6 (17.2) 77.1 (23.5)
3 4
3 4
3 4
3 4
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by Rapidrop Limited. The code of information for these model designations is as follows: Marking Rapidrop SPB SPNB SPWB 01 02 03 04 05 A B Description Company Name & Trademark The hose is threaded to a nipple on the inlet end and threaded to a reducer at the outlet. The hose is threaded to a nipple on the inlet end and the reducer is brazed to the flexible hose at the outlet The hose is brazed to a nipple on the inlet end and brazed to a reducer at the outlet Flexible Hose Lengths: 01 = 780 mm 02 = 1,220 mm 03 = 1,540 mm 04 = 1,880 mm 05 = 2,500 mm
1 2 3 4
Seung Jin Industry Co Ltd, 612, 5 Bar Shi-Wha Industrial Complex, 685-11 Sunggog-Dong, Ansan-Si Kyunggi-Do, 429-450 Korea
NPT in.
1 2
Model
2.6 (0.8) 8.5 (2.6) 2.6 (0.8) 8.5 (2.6) 2.6 (0.8) 8.5 (2.6)
8.3 (2.6) 31.8 (9.7) 7.6 (2.3) 31.4 (9.6) 8.3 (2.6) 31.8 (9.7)
1 2
3 4
3 4
1 2
1 2
FM Approvals
1-85
Model
NPT in.
3 4
CCXX-YYYY CCXX-YYYY
3 4
CC: Commercial Ceiling BU: Bushing Type XX: Product length. 08 through 26 (08 is a 0.8 m (2.6 ft) long hose assembly and 26 is a 2.6 m (8.5 ft) long hose assembly. YYYY: Year and month manufactured.
Approval of these 1 in. nominal dia. flexible metal sprinkler hose models is limited to use in providing sprinkler protection to commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Seung Jin Industry Co., Ltd.
Shanghai Genius Technical Corp Ltd, No. 7166 Zhong Chun Road, Qibao Town, Minhang District, Shanghai, P.R. China 201101
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9100. 1 in. nominal dia. two piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter is threaded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Shanghai Genius Technical Corp., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9120. 1 in. nominal dia. one piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and nipple is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Shanghai Genius Technical Corp., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9200. 1 in. nominal dia. one piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and nipple is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Shanghai Genius Technical Corp., Ltd.
NPT in.
1 2
Model
P-9210
2 (0.6)
6.5 (1.9)
FM Approvals
1-86
Model
NPT in.
1 2
1 2
1 2
Model P-9210. 1 in. nominal dia. one piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and coupling/threaded fitting is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Shanghai Genius Technical Corp., Ltd.
NPT in.
1 2
Model
1 2
1 2
1 2
Model P-9211. 1 in. nominal dia. one piece style flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. The sprinkler adapter and coupling/threaded fitting is welded to the flexible hose. Approval is limited for use in commercial suspended ceilings with a ceiling sprinkler system manufactured by Shanghai Genius Technical Corp., Ltd.
Super Flex Enterprises Co Ltd, No. 16, Lane 561, Sec. 2, Kouji Rd., Taoyuan City, Taoyuan, Taiwan, R.O.C.
NPT in.
1 2
Model
1.9 (0.6) 2.9 (0.9) 3.9 (1.2) 4.9 (1.5) 5.9 (1.8)
4.4 (1.4) 5.9 (1.9) 8.2 (2.6) 10.1 (3.2) 12.1 (3.7)
1 2
1 2
1 2
1 2
The model SP-A has a pressure rating of 230 psi (1585 kPa). 1 in. nominal diameter flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by Super Flex Enterprises Co., Ltd.
Virotec Rohrtechnik GmbH & Co KG, Meininger Weg 8, D-36132 Eiterfeld Germany
Model Designation NPT in.
1 2
VX-W-27-21-R-10 VX-W-27-21-NPT-10 VX-W-27-21-R-15 VX-W-27-21-NPT-15 VX-W-27-21-R-20 VX-W-27-21-NPT-20 VX-W-27-21-R-25 VX-W-27-21-NPT-25 VX-W-34-21-R-10 VX-W-34-21-NPT-10 VX-W-34-21-R-15 VX-W-34-21-NPT-15 VX-W-34-21-R-20 VX-W-34-21-NPT-20
3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0)
6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 15.2 (4.6) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0)
1 2
1 2
1 2
1 2
1 2
1 2
FM Approvals
1-87
Model Designation
NPT in.
1 2
VX-W-34-21-R-25 VX-W-34-21-NPT-25 VX-W-34-27-R-10 VX-W-34-27-NPT-10 VX-W-34-27-R-15 VX-W-34-27-NPT-15 VX-W-34-27-R-20 VX-W-34-27-NPT-20 VX-W-34-27-R-25 VX-W-34-27-NPT-25 VX-SW-27-21-R-10 VX-SW-27-21-NPT-10 VX-SW-27-21-R-15 VX-SW-27-21-NPT-15 VX-SW-27-21-R-20 VX-SW-27-21-NPT-20 VX-SW-27-21-R-25 VX-SW-27-21-NPT-25 VX-SW-27-21-90-R-10 VX-SW-27-21-90-NPT-10 VX-SW-27-21-90-R-15 VX-SW-27-21-90-NPT-15 VX-SW-27-21-90-R-20 VX-SW-27-21-90-NPT-20 VX-SW-27-21-90-R-25 VX-SW-27-21-90-NPT-25 VX-SW-27-27-R-10 VX-SW-27-27-NPT-10 VX-SW-27-27-R-15 VX-SW-27-27-NPT-15 VX-SW-27-27-R-20 VX-SW-27-27-NPT-20 VX-SW-27-27-R-25 VX-SW-27-27-NPT-25 VX-SW-27-27i-R-10 VX-SW-27-27i-NPT-10 VX-SW-27-27i-R-15 VX-SW-27-27i-NPT-15 VX-SW-27-27i-R-20 VX-SW-27-27i-NPT-20 VX-SW-27-27i-R-25 VX-SW-27-27i-NPT-25 VX-SW-34-21-R-10 VX-SW-34-21-NPT-10 VX-SW-34-21-R-15 VX-SW-34-21-NPT-15 VX-SW-34-21-R-20 VX-SW-34-21-NPT-20 VX-SW-34-21-R-25 VX-SW-34-21-NPT-25 VX-SW-34-21-90-R-10 VX-SW-34-21-90-NPT-10 VX-SW-34-21-90-R-15 VX-SW-34-21-90-NPT-15 VX-SW-34-21-90-R-20 VX-SW-34-21-90-NPT-20 VX-SW-34-21-90-R-25 VX-SW-34-21-90-NPT-25 VX-SW-34-27-R-10 VX-SW-34-27-NPT-10 VX-SW-34-27-R-15 VX-SW-34-27-NPT-15 VX-SW-34-27-R-20 VX-SW-34-27-NPT-20
8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0)
15.2 (4.6) 8.2 (2.5) 11.9 (3.6) 13.6 (4.1) 19.0 (5.8) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 15.2 (4.6) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 17.8 (5.4) 8.2 (2.5) 11.9 (3.6) 13.6 (4.1) 19.0 (5.8) 8.2 (2.5) 11.9 (3.6) 13.6 (4.1) 19.0 (5.8) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 15.2 (4.6) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 17.8 (5.4) 8.2 (2.5) 11.9 (3.6) 13.6 (4.1)
3 4
3 4
3 4
3 4
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
3 4
3 4
3 4
FM Approvals
1-88
Model Designation
NPT in.
3 4
VX-SW-34-27-R-25 VX-SW-34-27-NPT-25 VX-SW-34-27-90-R-10 VX-SW-34-27-90-NPT-10 VX-SW-34-27-90-R-15 VX-SW-34-27-90-NPT-15 VX-SW-34-27-90-R-20 VX-SW-34-27-90-NPT-20 VX-SW-34-27-90-R-25 VX-SW-34-27-90-NPT-25 VX-SW-34-34-R-10 VX-SW-34-34-NPT-10 VX-SW-34-34-R-15 VX-SW-34-34-NPT-15 VX-SW-34-34-R-20 VX-SW-34-34-NPT-20 VX-SW-34-34-R-25 VX-SW-34-34-NPT-25 VX-SW-34-34i-R-10 VX-SW-34-34i-NPT-10 VX-SW-34-34i-R-15 VX-SW-34-34i-NPT-15 VX-SW-34-34i-R-20 VX-SW-34-34i-NPT-20 VX-SW-34-34i-R-25 VX-SW-34-34i-NPT-25
8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5) 3.3 (1.0) 4.9 (1.5) 6.6 (2.0) 8.2 (2.5)
19.0 (5.8) 8.2 (2.5) 11.9 (3.6) 13.6 (4.1) 17.3 (5.3) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 15.2 (4.6) 6.8 (2.1) 9.0 (2.7) 10.0 (3.0) 15.2 (4.6)
3 4
3 4
3 4
3 4
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 in. nominal dia. flexible metal hose for providing a connection to automatic sprinklers in commercial suspended ceilings. Approval is limited for use in commercial suspended ceilings with a bracket system manufactured by Virotec Rohrtechnik GmbH & Co. KG.
Yong Won E.N.C. Ltd, 116-1 Seogu-Ri, Kwangjeuk-Myun, Yangju-Gun Keungki-Do, Korea
NPT in.
1 2
Model
2.2 (0.7) 8.2 (2.5) 2.2 (0.7) 8.4 (2.6) 2.2 (0.7) 8.4 (2.6)
18.6 (5.7) 91.5 (27.8) 5.5 (1.6) 15.2 (4.6) 5.7 (1.6) 17.0 (5.2)
1 2
1 2
1 2
3 4
3 4
Model YB25 and YB28. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial ceilings. Available in a range from 2.2 to 8.4 ft (700 mm to 2600 mm). Approval is limited for use in commercial suspended ceilings with a ceiling bracket system manufactured by Yong Won E.N.C., Ltd. These models are available as a two piece style and three piece style. The two piece style, the reducer is welded to the flexible hose and the nipple is connected to the flexible hose using a nut. The three piece style, the reducer and nipple is threaded to the flexible hose.
NPT in.
1 2
Model
1 2
3 4
3 4
FM Approvals
1-89
Model: YB28 A Type. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). This model is a one piece style as the reducer and nipple are welded to the flexible hose. Approval is limited for use in a wood tile ceiling. The tile size is 11.5 11.5 1 in. (292 292 25 mm) with a ceiling bracket system manufactured by Yong Won E.N.C., Ltd.
NPT in.
1 2
Model
1 2
3 4
3 4
Model: YB28 B Type. 1 in. nominal dia. flexible metal sprinkler hose for providing a connection to automatic sprinklers in commercial ceilings. Available in a range from 3.5 to 8.4 ft (1075 mm to 2575 mm). This model is a one piece style as the reducer and nipple are welded to the flexible hose. Approval is limited for use in a S.G.P Ceiling (metal panel). The tile size is 11.75 11.75 158 in. (300 300 41.3 mm), with a ceiling bracket system manufactured by Yong Won E.N.C., Ltd.
Merit Manufacturing, Division of Anvil International Inc, 110 Corporate Dr, Suite 10, Portsmouth NH 03801
Product Designation
1 2
in. NPT Outlet* 418 (105) 6 1 8 (156) 3 1 2 (89) 4 1 2 (114) 5 1 2 (140) 7 7 8 (200) 518 (131) 918 (232) 412 (114) 612 (165) 812 (216) 1078 (276)
3 4
in. NPT Outlet* 8.0 (203) 314 (83) 11.0 (280) 414 (108)
M3.175 F1.175
FM Approvals
1-90
Product Designation
F3.175 F3.175R
*These fittings have a 300 psi (2070 kPa) rated working pressure.
Virotec Rohrtechnik GmbH & Co KG, Meininger Weg 8, D-36132B 36132 Eiterfield, Germany
Product Designation Min Length, in. (mm) Max Length, in. (mm)
*These fittings are available with either a 38, 12 or 34 in. female NPT outlet sprinkler connection. These fittings are available with either a 38 or 12 in. female NPT outlet sprinkler connection. Product Designation Min Length, in. (mm) Max Length, in. (mm)
3.9 (99) 5.5 (140) 8.6 (218) 11.8 (300) 16.5 (419) 39.0 (991)
6.3 (160) 9.5 (241) 12.6 (320) 15.8 (401) 20.5 (521) 43.0 (1092)
These fittings have a male 1 in. NPT inlet (branch) connection. These fittings have a plain end inlet (branch) and must be threaded in the field. *Minimum length listed is based upon adjustment by screwing of the adjusting tube only. A 6.3 in. (160 mm) minimum length can be obtained on these fittings by cutting the inlet end and tapping a male 1 in. NPT. The VS 0.1 and VS 0.2 cannot be shortened.
Adjustment
3 in. 3 in.
1 2
These fittings are available with an optional escutcheon plate which can be positioned anywhere on the lower three inches of the fitting, to fit up to a clearance hole in the suspended ceiling. The escutcheon plate is not designed for use with a specific sprinkler, and is not to be fitted to any sprinkler body.
FM Approvals
1-91
Product Designation
These fittings have a 300 psi (2070 kPa) rated working pressure.
Remarks
3 4
Remarks
300 (2070)
a, b, c
a. Valve supplied with Female NPT inlet and outlet connection. b. Adjustable relief pressure settings from 0 to 75, 20 to 200, or 100 to 300 psi (0 to 515, 140 to 1380, or 690 to 2070 kPa). c. Not suitable for discharging the full rated pump capacity.
Remarks
300 (2070)
a, b, c
FM Approvals
1-92
Remarks: a. Valve supplied with Female NPT inlet and outlet connection. b. Adjustable relief pressure settings from 0 to 75, 20 to 200, or 100 to 300 psi (0 to 515, 140 to 1380, or 690 to 2070 kPa). c. Not suitable for discharging the full rated pump capacity.
Model 20
Remarks:
, 1, 1-12, 2, 2-12
300 (2070)
a, b, c
a. Valve supplied with Female NPT inlet and outlet connection. b. Relief pressure settings of 175, 250, or 300 psi (1205, 1725, or 2070 kPa). c. Not suitable for discharging the full rated pump capacity.
Kunkle Valve, Div of Tyco Valves and Control, 1221 Katherine Street NW, Cullman AL 35055
Product Designation Nominal Pipe Size Inches, NPT
3 4
Remarks
a, b, c a, b, c
a. Valve supplied with Male NPT inlet connection and Female NPT outlet connection. b. Adjustable relief pressure settings from 60 to 125, 126 to 175, or 176 to 250 psi (415 to 860, 870 to 1205, or 1215 to 1725 kPa). c. Not suitable for discharging the full rated pump capacity.
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Product Designation Nominal Pipe Size Inches, NPT
12, 34
Remarks
Model P4000
Remarks:
300 (2070)
a, b, c
a. Valve supplied with Female NPT inlet and outlet connection. b. Adjustable relief pressure settings from 0 to 75, 20 to 200, or 100 to 300 psi (0 to 515, 140 to 1380, or 690 to 2070 kPa). c. Not suitable for discharging the full rated pump capacity.
FM Approvals
1-93
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Model A61. 1 and 114 NPT female threaded connections. 5.6 nominal K-factor. 175 psi (1205 kPa) rated working pressure.
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Model A61. 1 and 114 in. NPT female threaded connections. 12 in. nominal orifice. 175 psi (1205 kPa) rated working pressure.
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Model A61. 1 and 114 NPT female threaded connections. 12 in. nominal orifice. 175 psi (1205 kPa) rated working pressure.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model CR commercial risers are intended for commercial applications in 112 through 8 in. nominal sizes. 300 psi (2070 kPa) rating.
Nominal Pipe Size, in. Description
112 2
112 2
Female by Female Metric Threaded Ends Female by Female Metric Threaded Ends
Model FCV floor control valves are intended for commercial applications in 112 through 8 in. nominal sizes. 300 psi (2070 kPa).
Nominal Pipe Size, in. Description
FM Approvals
1-94
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Model 513 is intended for commercial applications in 112 through 6 in. nominal sizes.
Nominal Pipe Size, in. Description
112 1 1 2 2-6
Male Threaded Inlet and Female Threaded Outlet Male Threaded Inlet and Male Threaded Outlet Grooved Inlet and Outlet
Model 513R is intended for residential applications in 112 through 2 in. sizes.
112 1 1 2 2 2 Male by Female Threaded Ends Male by Male Threaded Ends Grooved ends Male thread by grooved ends
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Line Tester. Model A59. 1 in. female pipe thread.
Flange Inlet Flange Outlet Grooved Inlet Grooved Outlet Flange Inlet Groove Outlet
3, 4, 6 3, 4 3, 4, 6
a, b, c b, c a, b, c
FM Approvals
1-95
Remarks: a. Available in ANSI and ISO flange patterns. b. FM Approved for horizontal and vertical installations in 3 in. NPS only. c. FM Approved for use with Model H retard chamber.
Model E. 212 in. and 65 mm. Model E-1 retard chamber. All valves available with flanged connections. Standard size valves painted black or gray. Metric size valves painted blue. Model E. 212 in. and 65 mm. Model E-1 retard chamber and E3 trim package. All valves available with flanged connections. Standard size valves painted black or gray. Metric size valves painted red (when supplied with ISO threads in valve trim). NOTE: The placement of a test and drain valve (E3 trim option) in lieu of the 2 (50 mm) drain valve does not replace the need for an inspectors test connection at the most remote location of the sprinkler system. The test and drain valve shall not be used in lieu of the inspectors test connection for the testing of the entire wet piping system. The test and drain valve shall only be used to exercise the clapper and check the mechanical alarm (water motor gong).
Angus Fire Sprinklers, Thame Park Rd, Oxfordshire OX9 3RT United Kingdom
End Connections Inlet x Outlet Nominal Valve Size, NPS Max Rated Working Pressure, psi (kPa)
Product Description
Remarks
Model C-1 Model C-1 Model C-1 Model C-1 Model C-1 Model C1-H
Remarks:
Flange x Flange Flange x Grooved Grooved x Grooved Flange x Flange Flange x Grooved Flange x Flange
4 in. (100 mm) 4 in. (100 mm) 4 in. (100 mm) 6, 8 in. (150, 200 mm) 6 in. (150 mm) 4 in. (100 mm)
290 (2000) 290 (2000) 290 (2000) 175 (1205) 175 (1205) 290 (2000)
a, b a, b a, b a, b a, b a, c
a. No retard chamber supplied. b. Limited to installation in vertical risers at locations having constant water supply pressures. c. Limited to horizontal installation at locations having constant water supply pressures.
Remarks
Model E Model C-1 Model C-1 Model C-1 Model C-1 Model C-1 Model C1-H
Remarks: a. b. c. d.
Flange Flange Flange Flange Flange Grooved Grooved Grooved Flange Flange Flange Grooved Flange Flange
3, 4, 6, 8 in. (80, 100, 150, 200 mm) 4 in. (100 mm) 4 in. (100 mm) 4 in. (100 mm) 6, 8 in. (150, 200 mm) 6 in. (150 mm) 3, 4 in. (80, 100 mm)
175 (1205) 290 (2000) 290 (2000) 290 (2000) 175 (1205) 175 (1205) 290 (2000)
a b, c b, c b, c b, c b, c b, d
FM Approved for use with Model E-1 retard chamber. No retard chamber supplied. Limited to installation in vertical risers at locations having constant water supply pressures. Limited to horizontal installation at locations having constant water supply pressures.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Models B, G-2. 4, 6, 8 in. NPS. Model J-1. 4, 6 in. Model J-2. 4, 6 in. Cut grooved inlet and outlet. Model H-1. 4, 6 in. Flanged inlet and outlet connections. Model H-1. 8 in. Flanged inlet and outlet connections. Vertical installation only. Model H-2. 4 in. Cut-grooved inlet and outlet connections.
FM Approvals
1-96
Model H-3. 4, 6 in. Flanged inlet to cut-grooved outlet. Model H-3. 8 in. Flanged inlet and outlet connections. Vertical installation only. Model H. 8 in. Flanged inlet and outlet connections. With Automatic Model B retard chamber. Limited to installation in vertical risers only. Models H-1, H-2, H-3, J-1, J-2. With Model B or H retard chamber. Models J-1 and J-2 limited to installation in vertical risers only. Model G. 3, 8 in. With Model E retard chamber. Limited to installation in vertical risers only.
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Product Designation Description Nominal Pipe Size, in. (mm) Max Working Pressure, psi (kPa) Remarks
Model NMX
a. Resilient seat. b. With Model NAV retard chamber.
175 (1205)
a, b
Paradise Industry Co Ltd, Plant 65-2 Chooneui-Dong, Woonmi-Ku, Bucheon City, Kyunggi-Do, Korea (420-120)
Model FAVB Water Flow Alarm Valves in sizes 100 and 150 mm NPS. Flanged inlet and outlet connections, ANSI or Korean Standard with others available. Suitable for vertical installation. Supplied with retard chamber.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model E. 212, 3, 4, 6, 8 in.; 65, 100, 150, 200 mm. Model E-1 retard chamber. All valves available with flanged connections. 3, 4, 6, 8 in. sizes also available with grooved outlets. Standard size valves painted black or gray. Metric size valves painted blue. Model E. 212, 3, 4, 6, 8 in., and 65, 100, 150, 200 mm. Model E-1 retard chamber and E3 trim package. All valves available with flanged connections. 3, 4, 6, 8 in. sizes also available with grooved outlets. Standard size valves painted black or gray. Metric size valves painted red (when supplied with ISO threads in valve trim). NOTE: The placement of a test and drain valve (E3 Trim option) in lieu of the 2 (50mm) drain valve does not replace the need for an inspectors test connection at the most remote location of the sprinkler system. The test and drain valve shall not be used in lieu of the inspectors test connection for the testing of the entire wet piping system. The test and drain valve shall only be used to exercise the clapper and check the mechanical alarm (water motor gong). Model E3. 4, 6, and 8 in., and 100, 165, 200 mm Model E-1 retard chamber, and E3 trim package. Valves are available with cut grooved inlet and outlet end connections, with a 300 psi (2070 kPa) maximum pressure rating. Standard size valves are painted black or red (when supplied with ISO threads in valve trim). Valves are considered FM Approved for horizontal and vertical installations. NOTE: The placement of a test and drain valve (E3 Trim option) in lieu of the 2 (50 mm) drain valve does not replace the need for an inspectors test connection at the most remote location of the sprinkler system. The test and drain valve shall not be used in lieu of the inspectors test connection for the testing of the entire wet piping system. The test and drain valve shall only be used to exercise the clapper and check the mechanical alarm (water motor gong).
Shanghai Jindun Fire-Fighting Security Service Co Ltd, 65# Henqiao Road Fanrong Industrial Area Zhoupu, Pudong, Shanghai, 201318, Peoples Republic of China
Model Number Product Type Nominal Pipe Size, Inch Rated Working Pressure, psi (kPa) Remarks
ZSFZ
Remarks:
4, 6, 8
232 (1600)
a, b
a. Available in ISO flange patterns only. b. Approved for use with Model ZSFZ retard chamber.
Tecnicas e Ingenieria de Proteccion SA (TIPSA), Apartado de Correos 293, 08720 Vilafranca del Penedes, Barcelona Spain
Model Number End Connections Inlet Outlet Nominal Valve Size, NPS Rated Working Pressure, psi (kPa) Remarks
P3 P4
Remarks:
a, b, c a, b, c
a. Available in ISO flange patterns. b. FM Approved vertical installations. c. FM Approved for use with Model T retard chamber.
FM Approvals
1-97
Total Walther GmbH, Feuerschutz und Sicherheit, Waltherstrasse 51, 51069 Koln, Germany
Model NV 100/3. 100 mm. Model NV 150/3. 150 mm. Model NV 200/3. 200 mm. The above are limited to installation at locations having constant water supply pressures. Model NV 200. 8 in. NPS.
Product Description
Remarks
AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1 AV-1
Remarks:
Flange x Flange Flange x Flange Flange x Groove Flange x Groove Groove x Groove Groove x Groove Flange x Flange Flange x Flange Flange x Groove Flange x Groove Groove x Groove Groove x Groove
4, 6, 8 in. 4, 6 in. 165 mm 4, 6, 8 in. 76.1 mm, 165 mm 4, 6 in. 165 mm 4, 6 in. 76.1 mm, 165 mm 4, 6 in. 165 mm 4, 6, 8 in. 4, 6, 8 in. 165 mm 212, 4, 6, 8 in. 76.1 mm, 165 mm 4, 6, 8 in. 165 mm 212, 4, 6, 8 in. 76.1 mm, 165 mm 4, 6, 8 in. 165 mm 212, 212,
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a, b, c d, e a, b, c d, e a, c d a, b, c a, d, e a, b, c a, d, e a, c a, d
a. FM Approved for use with Model RC-1 retard chamber. b. Available with Rp2 drain and ANSI, ISO, AS, or JIS flanges. Valves with Rp2 drain limited to vertical risers. Alarm test trim (Grinnell PSN 52-201-2-2002) must be according to installation requirements. c. 175 psi (1205 kPa) rated valves are supplied with grey iron bodies and covers. 300 psi (2070 kPa) rated valves are supplied with ductile iron bodies and covers. d. Approved for use with European trim for European installations. NOTE: The placement of a test and drain valve in lieu of the 2 inch (50 mm) NPS drain valve does not replace the need for an inspectors test connection at the most remote location of the sprinkler system. The test and drain valve shall not be used in lieu of the inspectors test connection for testing of the entire wet piping system. The test and drain valve shall only be used to exercise the clapper and check the mechanical alarm (water motor gong). e. Approved when supplied with ANSI, ISO, AS, or JIS flanges.
Tyco Fire Products Manufacturing Ltd, Stockport Trading Estate Yew St, Stockport Cheshire SK4 2JW, United Kingdom
Product Designation Description Nominal Pipe Size, in. (mm) Max Working Pressure, psi (kPa) Remarks
Model LW
3 (80)
175 (1205)
a, b
a. Resilient seat. b. Limited to installation at locations having constant water supply pressures.
Venus Fire Protection Ltd, 4105 Portland Blvd, Sherbrooke, Quebec J1L 1X9, Canada
Product Designation Description Nominal Pipe Size, in. (mm) Max Working Pressure, psi (kPa) Remarks
Alarm Check Valve, Flanged by Flanged Alarm Check Valve, Flanged by Grooved Alarm Check Valve, Grooved by Grooved
3, 4, 6, 8 4, 6, 8 4, 6
a, b, c a, b, c a, b, c
a. Resilient seat. b. With Model E retard chamber. c. Limited to installations with vertical risers only.
FM Approvals
1-98
Series 751 FireLock Series 751 FireLock Series 751 FireLock Series 751 FireLock Series 759 FireLock
Alarm Check Valve, Grooved Ends Alarm Check Valve, Flanged by Grooved Alarm Check Valve, Grooved Ends Alarm Check Valve, Flanged by Grooved Alarm Check Valve, Grooved Ends
112,
2, 3, 4, 6 76.1, 165.1 mm 4, 6 8 8
212,
300 (2065) 300 (2065) 225 (1550) 225 (1550) 175 (1205)
a, b, c a, b, c a, b, c a, b, c a, b, c
a. Resilient seat. b. Available with Series 752 retard chamber. c. Suitable for vertical or horizontal installation.
Alarm Check Valve, Flanged Ends Alarm Check Valve, Grooved Ends Alarm Check Valve, Flanged by Grooved
3, 4, 6, 8 (76, 80, 100, 150) 3, 4, 6, 8 (76, 80, 100, 150) 3, 4, 6, 8 (76, 80, 100, 150)
a, b a, b a, b
FM Approvals
1-99
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Model WFG. 2 through 8 in. NPS. Pneumatic retard and two snap switches. 250 psi (1725 kPa) rated working pressure. Contacts rated for 7 A at 125 V ac, 0.25 A at 24 V dc. A Model T tamper switch kit (P/N 546-6000) is available as optional equipment for field installation on the Model WFG device.
Potter Electric Signal & Manufacturing Ltd, 55 Glencameron Rd, Thornhill, Ontario L3T 1P2, Canada
Model VSR-D. 2 through 10 in. NPS. Furnished with two snap switches and pneumatic retard. Model VSR-T. 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS, for use with pipe having a wall thickness of 0.188 in. (5 mm). 250 psi (1725 kPa) rated working pressure. A tamper switch kit (P/N 5420220) is available as optional equipment for field installation on the Models VSR-D, VSR-T devices. Model VSR-E. 2 through 6 in. NPS. Furnished with two snap switches and pneumatic retard. 450 psi (3105 kPa) rated working pressure. Model VSR-F. 2 through 8 in. NPS. Furnished with two snap switches and pneumatic retard. 450 psi (3105 kPa) rated working pressure. Models VS-F, VSR-F. 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS (203 mm), for use with pipe having a wall thickness of 0.188 in. (5 mm), or Schedule 40 pipe.
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
Model VSR. 2 through 8 in. NPS. Furnished with two snap switches and pneumatic retard. 450 psi (3100 kPa) rated working pressure. Model VSR-TSK. 2 through 6 in. NPS. Furnished with two snap switches and pneumatic retard, and a tamper switch to indicate that the cover was removed. 450 psi (3100 kPa) rated working pressure. Model VSR-F. 2 through 8 in. NPS. Furnished with two snap switches and pneumatic retard. 450 psi (3105 kPa) rated working pressure. Models VS-F, VSR-F. 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS (203 mm), for use with pipe having a wall thickness of 0.188 in. (5 mm), or Schedule 40 pipe. Model VSR-FE-2. 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS, for use with pipe having a wall thickness of 0.188 in. (5 mm). All sizes also for use in Schedule 40 pipe. 450 psi (3105 kPa) rated working pressure. Furnished with electronic retard. Model VSR-FEX. 2 through 8 in. NPS. For simultaneous usage as explosionproof for Class I, Division 1, Groups C and D; dust-ignitionproof for Class II/III, Division 1, Groups E, F and G hazardous (classified) locations indoors and outdoors (NEMA Type 4); 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS, for use with pipe having a wall thickness of 0.188 in. (5 mm). All sizes also for use in Schedule 40 pipe. 450 psi (3105 kPa) rated working pressure. Furnished with pneumatic retard.
System Sensor, Div of Honeywell, 3825 Ohio Ave, Saint Charles IL 60174
Accuflow Model AFDXX, 2 through 8 in. NPS as indicated in table below. 2 through 5 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Two switches and a solid state retard. Contacts rated for 0.6 A, at 125 V ac, 2.0 A, 30 V dc.
Model No.* Nominal Pipe Size, mm
2 212 3 312 4 5 6 8
AFDXXA: Models AFD20A, 25A, 30-2A, 35A, 40A, 50A, 60A, and 80A for Canadian distribution have a factory installed tamper switch rated for 5 A at 125/250 V ac, 3 A at 30 V dc. AFDXXE: Accuflow Model AFDXXE, 2 through 8 in. NPS as indicated in table below. 2 through 4 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Two switches and a solid state retard. Contacts rated for 0.6 A, at 125 V ac, 2.0 A, 30 Vdc.
Model No.* Nominal Pipe Size, mm
Model 546-9000. Cover tamper switch available for Models AFD20 (E), 25 (E), 30 (E), 35, 40 (E), 50, 60 (E) and 80 (E) rated for 5 A at 125/250 V ac, 3 A at 30 V dc.
FM Approvals
1-100
Model WFD-XX 2 through 8 in. NPS as indicated in Table below. 2 through 4 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Two snap switches and pneumatic retard. 2 through 6 in. NPS sizes rated for Schedules 10 and 40. 8 in. NPS size rated for 0.188 in wall, Schedules 10 and 30 pipe.
Model No.* Nominal Pipe Size, mm
*Suitable for use in BS 1387 medium and heavy pipe, DIN 2448 and 2458 pipe. 2 through 4 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Two snap switches and pneumatic retard. Model No. Nominal Pipe Size, in.
2 212 3 3 312 4 5 6 8
Model WFD-10. 2 through 5 in. NPS, for use with Schedule 10 pipe; 6 in. NPS, for use with pipe having a wall thickness of 0.134 in. (3 mm); 8 in. NPS, for use with pipe having a wall thickness of 0.188 in. (5 mm). 450 psi (3105 kPa) rated working pressure. 2 through 5 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Model WFD-10 has two snap switches and pneumatic retard. Contacts rated for 7 A at 125 V ac, 0.25 A at 24 V dc.
Model No.* Nominal Pipe Size, in.
2 212 3 3 312 4 5 6 8
Model WFDXX-EXP 2 through 8 in. NPS as indicated in table below. These models are suitable for use in hazardous locations: Class I, Groups B, C, D Division 1, Class II, Groups E, F, G, Division 1, and Class III, Division 1 NEMA 4 enclosure. 2 through 5 in. NPS have a 450 psi (3105 kPa) rated working pressure. 6 and 8 in. NPS have a 400 psi (2760 kPa) rated working pressure. Two snap switches and pneumatic retard. Contacts rated for 10 A, at 125/250 V ac, 2.5 A, 24 V dc.
Model No.* Nominal Pipe Size, in.
2 212 3 3 312 4 5 6 8
*All models suitable for use in Schedule 40 pipe. Two snap switches and pneumatic retard. Two snap switches and pneumatic retard. Also for use with Schedule 10 pipe. Also for use with pipe having a wall thickness of 0.134 in. (3 mm). Also for use with pipe having a wall thickness of 0.188 in. (5 mm).
Models WFD20A, 25A, 30A, 40A, 50A, 60A, 80A for Canadian distribution have factory installed cover tamper switch rated for 5 A at 125/250 V ac, 2.5 A at 24 V dc. Model 546-7000. Cover tamper switch available for Models WFD20, 25, 30, 35, 40, 50, 60, 80 rated for 5 A at 125/250 V ac, 2.5 A at 24 V dc.
FM Approvals
1-101
Unless otherwise specified, these testers have 175 psi (1205 kPa) rated working pressure.
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Zonecheck Vane Type Waterflow Indicator Test Devices. Available in sizes 2 through 6 in. NPS. Can be original installation, or a retrofit, to run piping around indicator. All sizes available in Schedule 10 and 40 piping configurations. Either 120 V ac or 230 V ac power required.
Project Fire Products Ltd, Pasturefields Lane, Industrial Estate, Hixon, Staffordshire ST18 0PH, United Kingdom
Zonecheck Vane Type Waterflow Indicator Test Devices. Available in sizes 1 through 6 in. NPS. Can be original installation, or a retrofit, to run piping around indicator. All sizes available in Schedule 10, 40, BS 1387 Medium and Heavy piping configurations. Either 120 V ac or 230 V ac power required.
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Zonecheck Vane Type Waterflow Indicator Test Devices. Available in sizes 2 through 6 in. NPS. Can be original installation, or a retrofit, to run piping around indicator. All sizes available in Schedule 10 and 40 piping configurations. Either 120 V ac or 230 V ac power required.
Angus Fire Sprinklers, Thame Park Rd, Oxfordshire OX9 3RT, United Kingdom
Model D. 100, 150 mm NPS. Metric size valves painted blue.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Model 39. 4, 6 in. NPS. Flange/flange connection. Automatic Model 39A. 6 in. NPS. Flange/flange connection. Automatic Model GTO. 4, 6 in. NPS. Flange/groove connection.
FM Approvals
1-102
Magisco Valves Ltd, 53 Limes Rd, Tettenhall, Wolverhampton WV6 8RD, United Kingdom
MAG Model M799DG-04E. 3, 4, 6, 8 in. NPS. 300 psi rated working pressure. Available with wafer or flanged inlet and outlet connections.
Mil Ltd, 17 Moshe Beker St, Box 15200, Rishon Lezion 75051, Israel
Product Designation End Connection Nominal Pipe Size, in. (mm) Max Working Pressure, psi (kPa) Remarks
175 (2070)
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840, Bad Oldesloe, Germany
Product Designation End Connections Nominal Pipe Size, in. (mm) Max Working Pressure, psi (kPa) Remarks
Model TMX
175 (1205)
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model A. 212 in. NPS. 90 angle. Threaded or cut groove inlet and outlet connections. Model D. 4, 6 in. NPS; 100, 150 mm NPS. Standard size valves painted black or gray. Metric size valves painted blue. Flanged inlet. Flanged or grooved outlet. Model LDX low pressure Dry Pipe Valve System, 4 and 6 in. NPS, 100 and 150 mm NPS. Model LDX dry pipe valves have a flanged inlet and grooved outlet. Model LDX low pressure check valves have grooved inlet and outlet connections. The Model LDX Dry Pipe Valves are available with the optional Model B-1 Accelerator. Model DDX-LP Dry Pipe Valve System consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. NPS (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. The Model DDX-LP Dry Pipe Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. The Model DDX Deluge Valves have grooved inlet and grooved outlet end connections. The DDX-LP system is designed for systems with water supply pressures from 20 psi (138 kPa) to 250 psi (1724 kPa), and corresponding sprinkler system air pressures, nominally, of 12 psi (83 kPa) to 24 psi (165 kPa). A loss of system air pressure, such as when a sprinkler activates, opens the pneumatic actuator which opens the DDX valve, sending water to the sprinklers and sounding alarms. The system utilizes the Reliable Model LP (low pressure) pilot line actuator, the Reliable Model LP low pressure pneumatic actuator, the Reliable Model B Manual Pull Station, and a System Sensor EPS10-1 pressure alarm switch. The Reliable Model B1 accelerator is an available option for use with this system. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. The rated working pressure of the Model LP Dry Pipe Valve System is 250 psi (1724 kPa).
SES Enser Engineering, Via Carolina Romani 8/10, 20091 Bresso (MI), Italy
FARES Model F799DG-04E. 3, 4, 6, 8 in. NPS. 300 psi rated working pressure. Available with wafer or flanged inlet and outlet connections.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Model A. 2*, 3, 4, 6 in. NPS. Available with flange/flange and flange/groove end connections. Model A-1. 4, 6 in. NPS. Flange/Groove end connections.
*Also available with groove/groove end connections.
Venus Fire Protection Ltd, 4105 Portland Blvd, Sherbrooke, Quebec J1L 1X9, Canada
Astra Model A. 3, 4, 6 in. NPS. Flange/flange connection. Astra Model B. 4, 6 in. NPS. Flange/groove connection. Astra Model E. 4 in. NPS. Groove/groove connection.
FM Approvals
1-103
Optional system components include: Regulated Air Maintenance Trim Assemblies Series 757 or 757-P (with pressure switch) Air Maintenance Devices Series 746-LPA Accelerator System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 system air pressure supervisory switch Series 760 Water Motor Alarm Series 755 Manual Pull Station Series 705W water supply butterfly shutoff valve
All Dry Pipe Valves are available factory assembled in the Victaulic Series 745 Fire-Pac enclosure, a cabinet containing all system components and accessories, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply.
FM Approvals
1-104
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Models B, B1. For use with Reliable Model D or Star Model A dry pipe valve. The Model B-1 Accelerator is an optional component for use with the Reliable Model LDX Dry Pipe Valve System.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Model S430. For use with Grinnell or Gem Models F302, F3021, 4, 6 in. or Star Model A, 2, 3, 4, 6 in. NPS dry pipe valves, 4, 6 in. Duomatic dry systems (Refrigerated Area Sprinkler Systems).
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Model 1 Accelerator. For use with Automatic Model 39 dry pipe valve.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Accelerator. Model C.
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Model SE2 Accelerator. For use with Model TMX dry pipe valves.
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
Model QRS Electronic Accelerator System. Consists of a Potter Model QRS Quick Release Pressure Switch, Potter Model PFC-100RC Fire Alarm Releasing Panel, Skinner Model 73218BN4UNLVNOC111C2 solenoid valve and associated trim for use on the following dry pipe valves:
Manufacturer Model No. Size, in.
212,
Note 1: The Model QRS Accelerator with Model PFC-100RC Panel is configured such that one accelerator and one control panel is utilized for one dry pipe valve.
Model QRS Electronic Accelerator System. Consists of a Potter Model QRS Quick Release Pressure Switch, Potter Model PFC-4410-RC Fire Alarm Releasing Panel, Skinner Model 73218BN4UNLVNOC111C2 solenoid valve and associated trim for use on the following dry pipe valves (Note 2) and a preaction valve (Note 3): Dry Pipe Valves
Manufacturer Model No. Size, in.
212,
Note 2: The Model PFC-4410-RC Panel, standard program #14, is configured such that one control panel can be utilized for up to four dry pipe valves with four Model QRS Accelerators.
DV-5
112 thru 8
Note 3: The Model PFC-4410-RC Panel, standard program #13, is configured such that one control panel is utilized for one preaction valve with one Model QRS Accelerator.
FM Approvals
1-105
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Star Exhauster. Model BB.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Models A, A-1.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Models H-1, H-2, H-3.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Models A-2, B-1, B-2.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Models A, B.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Air Compressor Panel. Reliable Model B. Automatic Air Pressure Maintenance Device. Reliable Model C.
FM Approvals
1-106
FM Approvals
1-107
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Suprotex Deluge System*. Consists of Model C automatic water control valve, sizes 212, 6 in.; 18 in. circuit tubing with the following Heat Actuated Devices (HADs): 87-100A, 87-150, 87-180, 87-190, 87-530A, 87-540A, 87-560, 87-570; No. 90-100 compensating vent; Nos. 81-100A, 83-100A releases; Nos. 81-600A, 83-600 secondary releases (only acceptable when rate-of-rise circuits are a secondary means of system activation); Model 70-200 break glass station; manual pull handle; Model 64-100G manual pull station; No. 148-200C air pump panel; No. 2403C2H low pressure regulator; No. 79-340A air dryer; No. 39-713 drum drip or No. 79-943C reservoir; No. 1621 high pressure regulator; No. 148-250 restriction orifice; No. 79-840B air line mercury check; No. 121 mercury check; No. S76-650 weight switch; Model 94-160 low pressure actuator; emergency release (quick opening valve); Model 123-100 hydropneumatic control. Automatic Deluge Sprinkler System. Consists of Model D, F water control valves, 212, 4, 6 in. or Model E water control valve, 6 in., which must be equipped with Viking Model C-1 pressure-operated relief valve.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Consists of Model F Water Control Valve. 212, 4, 6 in. Consists of Model D1.5, 112 in. NPS, and Model D2, 2 in. NPS, Water Control Valves.
Magisco Valves Ltd, 53 Limes Rd, Tettenhall, Wolverhampton WV6 8RD, United Kingdom
MAG Model M799DG-04A (wet pilot), MAG Model M799DG-04B (dry pilot), MAG Model M799DG-04C (electric). Consists of 3, 4, 6, 8 in. NPS MAG Model M799DG-04 automatic water control valve. MAG Models M799DG-04A and M799DG-04B have a rated working pressure of 300 psi (2070 kPa).
Mil Ltd, 17 Moshe Beker St, Box 15200, Rishon Lezion 75051, Israel
INBAL Model 799-DG-01-HMP (wet pilot) and INBAL Model 799-DG-01-PMP (dry pilot). Consists of 3, 4, 6, 8 in. NPS INBAL Model 799-DG-01 water control valve. 6 in. NPS rated working pressure of 300 psi (2070 kPa). INBAL Model 799-DG04-A (wet pilot), INBAL Model 799-DG04-B (dry pilot), INBAL Model 799-DG04-C (electric). Consists of 3, 4, 6, 8 in. NPS INBAL Model 799-DG04 automatic water control valve. INBAL Models 799-DG04-A and 799-DG04-B have a rated working pressure of 300 psi (2070 kPa).
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Deluge Sprinkler Systems. Consists of Model FSX deluge valves with either Electric, Dry Pilot Line, or Wet Pilot Line releasing means. The valves are available in Flange by Flange end connections, DIN sizes of 50, 80, 100, and 150 mm NPS. The electric solenoid is an impulse type solenoid valve, Minimax P/N 84 0131. The dry pilot line actuator is a diaphragm valve, Minimax P/N 20 9353-E. With electrical releasing, the Minimax control panel FMZ 4100 GAB 32, with 90 hours of 24 Vdc battery backup is used. The Models FSX deluge valves have a rated working pressure of 232 psi (16 bar).
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Deluge Sprinkler System consists of Model A, 212 in. NPS and Models B and BX in sizes 4 and 6 in. and 100 and 150 mm NPS deluge valves. Model BX deluge valves have an external reset feature. Systems are FM Approved for hydraulic, pneumatic or electric releasing means. Model DDX Deluge Sprinkler System. Consists of Model DDX Deluge Valves in sizes 4 inch and 6 inch NPS (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. Systems are Approved for hydraulic (wet pilot line), pneumatic (dry pilot line), or electric (solenoid valve) releasing means. Model DDX valves have grooved inlet and grooved outlet end connections. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. The Wet Pilot Trim. Set is connected to the push rod chamber outlet and provides the 2 inch main drain, the alarm test, the water supply pressure gage, and the push rod chamber supply connections. A wet pilot line, which extends up to the open deluge sprinkler grid, contains a closed sprinklers or other fixed temperature releases. When the closed sprinkler is activated and opened by a fire, the pilot line pressure
FM Approvals
1-108
is released which opens the DDX valve, sending water to the sprinklers and sounding alarms. The Wet Pilot Trim set is used when the Reliable Model F1-FTR fixed temperature release is used in the wet pilot line, and/or when the Reliable Model A or B emergency stations/manual pull boxes can be used for releasing. The rated working pressure of the Wet Pilot Deluge System is 250 psi (1724 kPa). The Dry Pilot Trim. Set is used when a fixed temperature release is used in the dry pilot line. A dry pilot line, which extends up to the open deluge sprinkler grid, contains closed sprinklers or other fixed temperature releases. When a closed sprinkler is activated and opened by a fire, the pilot line pressure is released which opens the pneumatic actuator, which opens the DDX valve, sending water to the sprinklers and sounding alarms. The Reliable Model LP (low pressure) pilot line actuator is used in the dry pilot line and is designed for systems with water supply pressures from 20 psi (138 kPa) to 250 psi (1724 kPa), and corresponding dry pilot line pneumatic pressures, nominally, of 12 psi (83 kPa) to 24 psi (165 kPa). The system uses the Reliable Model A or B emergency stations/manual pull boxes which can be used for manual releasing. The rated working pressure of the Dry Pilot Deluge System is 250 psi (1724 kPa). The Electric Actuation Trim. Set is connected to the push rod chamber outlet and provides the 2 inch main drain, the alarm test, the water supply pressure gage, and the push rod chamber supply connections. The Reliable Model A or B emergency stations/manual pull boxes can be used for manual releasing. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel is utilized for the electric release and alarm functions. Only when there is an electrical signal to the releasing control panel from a fire detector, such as when a fixed temperature heat detector is activated, does the solenoid valve open which opens the DDX valve, sending water to the sprinklers. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The system utilizes the normally closed solenoid valve, Reliable P/N 6871020020. The rated working pressure of the Electric Actuation Deluge System is 250 psi (1724 kPa).
SES Enser Engineering, Via Carolina Romani 8/10, 20091 Bresso (MI), Italy
FARES Model F799DG-04A (wet pilot), FARES Model F799DG-04B (dry pilot), FARES Model F799DG-04C (electric). Consists of 3, 4, 6, 8 in. NPS FARES Model 799-DG04 automatic water control valve. FARES Models F799DG-04A and F799DG-04B have a rated working pressure of 300 psi (2070 kPa).
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Star Deluge Sprinkler System. Consists of Model D water control valve, 3, 6 in. NPS. With 24 V dc operating coils. Star Hidromatic Deluge Sprinkler System. Consists of Model G, 3, 4, 6 in. NPS water control valve. Star Hidromatic Deluge Sprinkler System. Consists of Model G-1, 3, 4, 6 in. NPS water control valve. Model G-1 water control valves have an external reset feature. Systems are FM Approved for hydraulic, pnuematic or electric release trim. Rated working pressure is 250 psi (2070 kPa). Star Deluge Sprinkler System. Consists of Model F430 thermal control valve, 1, 112 in. NPS; Model B flooding valve, 2 in. NPS. Star Deluge Sprinkler System. Consists of Model B flooding valve, 2 in. NPS.
Total Walther GmbH, Feuerschutz und Sicherheit, Waltherstrasse 51, 51069 Koln, Germany
Deluge Sprinkler System. Consists of Model EKFV water control valve. DN 200 mm. A spool piece containing a 2 in. (51 mm) drain valve is attached to the inlet flange of each valve.
112, 2 (40, 50) 112, 2, 3, 4, 6, 8 (40, 50, 80, 100, 150, 200) 3, 4, 6, 8 (80, 100, 150, 200) 3, 4, 6, 8 (80, 100, 150, 200)
The Deluge Sprinkler Systems, with the DV-5 water control valve, is available factory assembled vertically inside the Model DV-5 Red-E Cabinet in sizes 112, 2, 3, 4, and 6 in. NPS. The Red-E cabinet and assembled system components comprise an integrated fire protection system which is assembled and tested at the factory. The cabinet contains: the system shutoff valve, Model DV-5 deluge valve, 24 Vdc battery backup, and an electrical control/release panel which is pre wired to the switches for the alarm, supervisory, and trouble functions. Installation requires the connection to the water inlet and outlet, main drain, electrical power supply, and the alarm and detection circuits. When dry pilot release is utilized, a built-in air compressor and air maintenance device provides controlled pilot line air pressure.
FM Approvals
1-109
Series 768 alarm line 3-Way Ball Valve for alarm/test/of Series 768 dry pilot line Air Manifold Assembly with integral restrictor/screen/anti-flood ball check valve Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: Regulated pilot line Air Maintenance Trim Assemblies Series 757 or 757-P (with pressure switch) Air Maintenance Devices System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 pilot line system air pressure supervisory switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
Series 769 Firelock NXT Deluge Valves with Wet Pilot Line Hydraulic Release. Sizes 112, 2, 212, 3, 4, 6 and 8 in. NPS. Grooved inlet and grooved outlet, installed vertically. The system rated working pressure is 300 psi (2070 kPa). Major trim components consist of the following: Series 749 Auto Drain pressure operated piston charge line water relief valve Series 729 alarm line Drip Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: System Sensor EPS10-2 alarm line pressure switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
Series 769 Firelock NXT Deluge Valve with Electric Release. Sizes 112, 2, 212, 3, 4, 6 and 8 in. NPS. Grooved inlet and grooved outlet, installed vertically. The system rated working pressure is 300 psi (2070 kPa). Major trim components consist of the following: Series 753-E normally closed solenoid valve Series 749 Auto Drain pressure operated piston charge line water relief valve Series 729 alarm line Drip Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: System Sensor EPS10-2 alarm line pressure switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
The 112, 2, 212, 3, 4, and 6 in. NPS Deluge Sprinkler Systems are available factory assembled in the Victaulic Series 745 Fire-Pac enclosure, a cabinet containing all system components and accessories, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. The Series 745 Fire-Pacs may be connected to Notifier AFP-200 Programmable Analog Fire control with software no. AFP2R2.42 or System Sensor PDRP-1001 fire control with operating system firmware revision level A. The AFP-200 control contains FMM-1 Module with a signaling line circuit which can be configured to meet Styles 4, 6 or 7 wiring performance as described in NFPA72. The addressable panels utilize model XP-10M module which may be configured at the factory to monitor the Fire-Pac cabinet and valve station. Optional LED Interface Module 4XTM and Relay Module RTM-8 provide outputs for auxiliary applications.
Deluge Sprinkler Systems, which utilize the angle type main water control valves, are available factory assembled in the Viking Total Pac2 enclosure, a second generation enclosure which replaces the Total Pac. The Total Pac2 is available in several configurations: 1) the system
FM Approvals
1-110
fully enclosed on legs with an access door and a built in electrical control panel (when electric activation required); 2) the valve system fully enclosed on legs with an access door and a remote control panel; 3) the valve system assembled to a skid and used with a remote control panel. All Deluge Sprinkler Systems are available with the TrimPac package in both conventional and Easy Trim configurations.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Suprotex Preaction Sprinkler System*. Consists of Model C, 212, 6 in. water control valve; FM Approved rubber-faced check valve; 18 in. circuit tubing with the following Heat Actuated Devices (HADs): 87-500B, 87-550, 87-580, 87-590, 87-530A, 87-540A, 87-560, 87-570; No. 90-100 compensating vent; Nos. 81-100A, 83-100A releases; Nos. 81-600A, 83-600 secondary releases (only acceptable when rate-of-rise circuits are a secondary means of system activation); Model 70-200 break glass station; manual pull handle; Model 64-100G manual pull station; No. 148-100C air pump panel; No. 2403C2H low pressure regulator; No. 79-904B or 79-904C low pressure alarm switch; No. 79-340A air dryer; No. 39-713 drum drip or No. 79-943C reservoir; No. 1621 high pressure regulator; No. 148-250 restriction orifice; No. 79-840B air line mercury check; No. 121 mercury check; No. S76-650 weight switch; Model 94-160 low pressure actuator; emergency release (quick opening valve); Model 123-100 hydropneumatic control. Automatic Preaction Sprinkler System. Consists of Model D, F water control valves, 212, 4, 6 in. with FM Approved rubber-faced check valve or Model E water control valve, 6 in. equipped with Viking Model C-1 pressure-operated relief valve and FM Approved rubber-faced check valve.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Consists of Model F Water Control Valve. 212, 4, 6 in. with FM Approved water-faced check valve. Consists of Model D1.5, 112 in. NPS, and Model D2, 2 in. NPS, Water Control Valves.
FM Approvals
1-111
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Preaction Sprinkler System consists of Model A, 212 in. NPS and Models B and BX 4 or 6 in. NPS water control valves and FM Approved rubber-faced check valve. Model BX, in sizes 4 and 6 in., as well as 100 and 150 mm NPS, water control valves have an external reset feature. Systems are FM Approved for hydraulic, pneumatic or electric releasing means. Preaction Sprinkler Systems utilizing electric releasing means are available factory assembled in the Reliable PrePak enclosure, both the Model A PrePak Preaction System, size 212 in., and the Model BX PrePak Preaction System, utilizing a size 4 or 6 in. Model BX deluge valve. The PrePak enclosure and assembled valve systems comprise an integrated fire protection system which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Preaction Sprinkler Systems. A Supertrol Single Interlock Preaction, consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. Model DDX valves have grooved inlet and grooved outlet end connections. The system utilizes low pressure, nominally 2 psi (13.8 kPa), sprinkler system supervisory air pressure to activate alarms, with electric activation for a valve trip. A loss of system air pressure, such as when a sprinkler activates, will not open the Model DDX valve but causes the low pressure alarm to sound. Only when there is also an electrical signal to the releasing control panel from a fire detector, such as when a fixed temperature heat detector is activated, does the solenoid valve open which opens the DDX valve, sending water to the sprinklers. The Reliable Model A or B emergency stations/manual pull boxes can be used for manual releasing. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel is utilized for the electric release and alarm functions. The release solenoid valve is the Reliable P/N 6871020020. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The rated working pressure of the Supertrol Single Interlock Preaction System is 250 psi (1724 kPa).
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Star Preaction Sprinkler System. Consists of Model G Hidromatic, 4 in. NPS water control valve and FM Approved rubber-faced check valve. Star Preaction Sprinkler System. Consists of Model B, 2 in. flooding valve and FM Approved rubber-faced check valve.
112, 2 (40, 50) 112, 2, 3, 4, 6, 8 (40, 50, 80, 100, 150, 200) 3, 4, 6, 8 (80, 100, 150, 200) 3, 4, 6, 8 (80, 100, 150, 200)
The Preaction Systems, with the DV-5 water control valve, are available factory assembled vertically inside the Model DV-5 Red-E Cabinet in sizes 112, 2, 3, 4, and 6 in. NPS. The Red-E cabinet and assembled system components comprise an integrated fire protection system which is assembled and tested at the factory. The cabinet contains: the system shutoff valve, Model DV-5 deluge valve, 24 Vdc battery backup, and an electrical control/release panel for the solenoid valve release. The control panel is prewired to the switches for the alarm, supervisory, and trouble functions. Installation requires the connection to the water inlet inlet and outlet, main drain, electrical power supply, and the alarm and detection circuits. A built-in air compressor and air maintenance device provides controlled system air pressure.
FM Approvals
1-112
Series 748 anti-flood Ball Check Valve Series 729 alarm line Drip Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 system air pressure supervisory switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
All preaction sprinkler systems discussed above offer the Series 75-B supplemental alarm valve as an option recommended for systems where continuous flow to the alarm port, which supplies flow to the water motor alarm, must be positively maintained. Some Preaction Sprinkler Systems are available factory assembled in the Victaulic Series 745 Fire-Pac enclosure, a cabinet containing all system components and accessories, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. The Series 745 Fire-Pacs may be connected to Notifier AFP-200 Programmable Analog Fire control with software no. AFP2R2.42 or System Sensor PDRP-1001 fire control with operating system firmware revision level A. The AFP-200 control contains FMM-1 Module with a signaling line circuit which can be configured to meet Styles 4, 6 or 7 wiring performance as described in NFPA72. The addressable panels utilize model XP-10M module which may be configured at the factory to monitor the Fire-Pac cabinet and valve station. Optional LED Interface Module 4XTM and Relay Module RTM-8 provide outputs for auxiliary applications.
FM Approvals
1-113
Refrigerated area sprinkler systems which are operated pneumatically/hydraulically are FM Approved as complete systems. Only the listed components for a given system may be used in combination. Fire detection systems which are operated electrically are FM Approved on a component basis. Only compatible components may be used in combination.
Anber Globe SA, Av de Las Flores 13, Parque Ind El Molino, 28970 Humanes de Madrid, Madrid Spain
Type A Supertrol Refrigerated Area System. Double interlocked supervised refrigerated area sprinkler system, controlled by an electric release system and pneumatic system pressure. Consists of a Model B or BX deluge valve (4, 6 in. NPS), compatible solenoid valve, Model A dry pilot actuator, Model B1 or A2, air pressure maintenance device, Model A hydraulic manual pull box, or Model B manual emergency station, United Electric switch Models J54-8300 and J54-8295 or system sensor EPS10 and EPS40 series pressure alarm switches, Approved rubber faced check valve and an Approved compatible automatic release control panel with appropriately sized battery to provide 90 hours emergency power. Only Approved fixed temperature heat sensitive devices shall be used in the release system and in the sprinkler piping. Type D Supertrol Refrigerated Area System. Double interlocked supervised refrigerated area sprinkler system, controlled by an electric release system and pneumatic system pressure. Consists of a Model B or BX deluge valve (4, 6 in. NPS) or Model A deluge valve (212 in. NPS), compatible solenoid valve, Model B1, or A2, air pressure maintenance device, Model A hydraulic manual pull box, or Model B manual emergency station, United Electric switch Models J54-8300 and J54-8295 or system sensor EPS10 and EPS40 series pressure alarm switches, Approved rubber faced check valve and an Approved compatible automatic release control panel capable of cross-zone operation with appropriately sized battery to provide 90 hours emergency power. Only Approved fixed temperature heat sensitive devices shall be used in the release system and in the sprinkler piping. Type D Supertrol Refrigerated Area Sprinkler Systems are available factory assembled in the PrePak enclosure and the Model BX PrePak Refrigerated Area Sprinkler System, utilizing a size 4 or 6 in. Model BX deluge valve. The PrePak enclosure and assembled valve systems comprise an integrated fire protection system which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Supertrol Type D Double Interlock Preaction System, pneumatic-electric/electric, consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. Model DDX valves have grooved inlet and grooved outlet end connections. The system utilizes low pressure, nominally 10 psi (69 kPa), sprinkler system supervisory air pressure and a cross-zoned releasing control panel such that two electrical signals must energize two control panel initiating circuits before water flows through the valve. A loss of system air pressure, such as when a sprinkler activates, activates the EPS10-2 pressure switch and provides one signal to the control panel. An electrical signal from a fire detector, such as when a fixed temperature heat detector is activated, provides the other signal to the control panel. The two signals open the solenoid valve, P/N 6871020020, and results in flow out the sprinklers. The Model A or B emergency stations/manual pull boxes can be used for manual releasing. The Model B1 accelerator is an available option for use with this system. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel, adjusted for cross-zoned operation, is utilized for the electric release and alarm functions. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The rated working pressure of the Supertrol Type D Double Interlock Preaction System is 250 psi (1724 kPa). Supertrol Type F Double Interlock Preaction System, pneumatic/electric, consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. Model DDX valves have grooved inlet and grooved outlet end connections. The Type F system is designed for systems with water supply pressures from 20 psi (138 kPa) to 250 psi (1724 kPa), and corresponding sprinkler system pneumatic pressures, nominally, of 12 psi (83 kPa) to 24 psi (165 kPa). A loss of system air pressure, such as when a sprinkler activates, opens the Model LP (low pressure) pilot line actuator causing the low pressure alarm to sound, but the DDX valve remains closed. The system utilizes the System Sensor EPS10-2 pressure alarm switch. Only when there is also an electrical signal to the releasing control panel from a fire detector, such as when a fixed temperature heat detector is activated, does the solenoid valve, P/N 6871020020, open which opens the DDX valve, sending water to the sprinklers. The Model A or B emergency stations/manual pull boxes can be used for manual releasing. The Model B1 accelerator is an available option for use with this system. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. This systems Notifier RP 1001 Fire Alarm/ Releasing Control Panel is utilized for the electric release and alarm functions. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The rated working pressure of the Supertrol Type F Double Interlock Preaction System is 250 psi (1724 kPa).
FM Approvals
1-114
Magisco Valves Ltd, 53 Limes Rd, Tettenhall, Wolverhampton WV6 8RD, United Kingdom
Sprinkler System. Double interlocked, uses a deluge valve controlled by an electric release system and pneumatic system pressure. Consists of 3, 4, 6, 8 in. NPS MAG Model M799DG-04K automatic water control valve, Model 284-08 3-way pilot, Model 377 pneumatic actuator, Model 379 air reset unit, Model 375 flow release pilot, Skinner Model 73218BN4UNLVN0C111C2 or ASCO Model 8210G207, 24 V dc solenoid valve, compatible FM Approved automatic release control panel with appropriately sized battery to provide 90 hours of emergency power. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping.
Mil Ltd, 17 Moshe Beker St, Box 15200, Rishon Lezion 75051, Israel
Sprinkler System. Double interlocked, uses a deluge valve controlled by an electric release system and pneumatic system pressure. Consists of 3, 4, 6, 8 in. NPS INBAL Model 799-DG04-K automatic water control valve, Model 284-08 3-way pilot, Model 377 pneumatic actuator, Model 379 air reset unit, Model 375 flow release pilot, Skinner Model 73218BN4UNLVN0C111C2 or ASCO Model 8210G207, 24 V dc solenoid valve, compatible FM Approved automatic release control panel with appropriately sized battery to provide 90 hours of emergency power. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Type A Supertrol Refrigerated Area System. Double interlocked supervised refrigerated area sprinkler system, controlled by an electric release system and pneumatic system pressure. Consists of a Reliable Model B or BX, in sizes 4 and 6 in., as well as 100 and 150 mm NPS, water control valve, compatible solenoid valve, Reliable Model A dry pilot actuator, Reliable Model B1, or A2, air pressure maintenance device, Reliable Model A hydraulic manual pull box, or Model B manual emergency station, United Electric switch Models J54-8300 and J54-8295 or system sensor EPS10 and EPS40 series pressure alarm switches, FM Approved rubber faced check valve and an FM Approved compatible automatic release control panel with appropriately sized battery to provide 90 hours emergency power. Only FM Approved fixed temperature heat sensitive devices shall be used in the release system and in the sprinkler piping. Type D Supertrol Refrigerated Area System. Double interlocked supervised refrigerated area sprinkler system, controlled by an electric release system and pneumatic system pressure. Consists of a Reliable Model B or BX, in sizes 4 and 6 in., as well as 100 and 150 mm NPS, or Reliable Model A deluge valve (212 in. NPS), compatible solenoid valve, Reliable Model B1, or A2, air pressure maintenance device, Reliable Model A hydraulic manual pull box, or Model B manual emergency station, United Electric switch Models J54-8300 and J54-8295 or system sensor EPS10 and EPS40 series pressure alarm switches, FM Approved rubber faced check valve and an FM Approved compatible automatic release control panel capable of cross-zone operation with appropriately sized battery to provide 90 hours emergency power. Only FM Approved fixed temperature heat sensitive devices shall be used in the release system and in the sprinkler piping. Type D Supertrol Refrigerated Area Sprinkler Systems are available factory assembled in the Reliable PrePak enclosure, both the Model A PrePak Refrigerated Area Sprinkler System, size 212 in., and the Model BX PrePak Refrigerated Area Sprinkler System, utilizing a Model BX deluge valve, in sizes 4 and 6 in., as well as 100 and 150 mm NPS. The PrePak enclosure and assembled valve systems comprise an integrated fire protection system which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Type F Supertrol Refrigerated Area System. Double interlocked supervised refrigerated area sprinkler system, controlled by an electric solenoid valve release in series with a pneumatic pressure release pneumatic actuator. Consists of a Reliable Model B or BX Deluge valve, a Model G Right-Check riser valve, both in sizes of 4 or 6 in. NPS, as well as in sizes 100 and 150 mm NPS. Model B or BX Deluge valves have ANSI flanged inlets and grooved outlets. Model G Right-Check riser valves have grooved inlets and outlets. Also utilized are: a Reliable Model LDX pneumatic actuator, Reliable Models B-2 or A-2 air pressure maintenance devices, a Reliable Model B manual emergency pull station, a System Sensor EPS 10-1 pressure switch, or a United Electric J54-A-8300, forlow air pressure supervision, and a System Sensor EPS 10-2, or a United Electric J54-A-8295, for water flow indication. The Reliable Model B1 accelerator is an available option for use with this system. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel is utilized for the electric release and alarm functions. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has a appropriately sized battery, Notifier Model PS 12120, to provide 90 hours emergency power. Compatible 24Vdc energized NC solenoid valves are listed in the Automatic Water Control Valve section of this Guide. System rated working pressure is 175 psi. The Type F Supertrol Refrigerated Area Sprinkler Systems are available factory assembled in the the PrePak enclosure. The PrePak enclosure integrates the complete fire protection system in a cabinet which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Supertrol Type D Double Interlock Preaction System. Pneumatic-electric/electric, consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the
FM Approvals
1-115
clapper. Model DDX valves have grooved inlet and grooved outlet end connections. The system utilizes low pressure, nominally 10 psi (69 kPa), sprinkler system supervisory air pressure and a cross-zoned releasing control panel such that two electrical signals must energize two control panel initiating circuits before water flows through the valve. A loss of system air pressure, such as when a sprinkler activates, activates the EPS10-2 pressure switch and provides one signal to the control panel. An electrical signal from a fire detector, such as when a fixed temperature heat detector is activated, provides the other signal to the control panel. The two signals open the solenoid valve, Reliable P/N 6871020020, and results in flow out the sprinklers. The Reliable Model A or B emergency stations/manual pull boxes can be used for manual releasing. The Reliable Model B1 accelerator is an available option for use with this system. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel, adjusted for cross-zoned operation, is utilized for the electric release and alarm functions. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The rated working pressure of the Supertrol Type D Double Interlock Preaction System is 250 psi (1724 kPa). Supertrol Type F Double Interlock Preaction System, pneumatic/electric. Consists of Model DDX Deluge Valves in sizes 4 in. and 6 in. (100 mm and 150 mm) NPS. A mechanical latch prevents the valve from resetting after the initial trip. Model DDX Deluge Valves have an external reset feature whereas a knob attached to the outside of the valve body is pushed in and then rotated manually to reseat the clapper. Model DDX valves have grooved inlet and grooved outlet end connections. The Type F system is designed for systems with water supply pressures from 20 psi (138 kPa) to 250 psi (1724 kPa), and corresponding sprinkler system pneumatic pressures, nominally, of 12 psi (83 kPa) to 24 psi (165 kPa). A loss of system air pressure, such as when a sprinkler activates, opens the Reliable Model LP (low pressure) pilot line actuator causing the low pressure alarm to sound, but the DDX valve remains closed. The system utilizes the System Sensor EPS10-2 pressure alarm switch. Only when there is also an electrical signal to the releasing control panel from a fire detector, such as when a fixed temperature heat detector is activated, does the solenoid valve, Reliable P/N 6871020020, open which opens the DDX valve, sending water to the sprinklers. The Reliable Model A or B emergency stations/manual pull boxes can be used for manual releasing. The Reliable Model B1 accelerator is an available option for use with this system. In the event that water builds up inside the deluge valve due to condensate from the air supply system or water from a valve trip, a drain valve is provided to drain the valve body and riser. This systems Notifier RP 1001 Fire Alarm/Releasing Control Panel is utilized for the electric release and alarm functions. Only FM Approved fixed temperature heat devices shall be used in the release system and in the sprinkler piping. The control panel has an appropriately sized battery, Notifier Model PS 12120, to provide 90 hours of backup emergency power. The rated working pressure of the Supertrol Type F Double Interlock Preaction System is 250 psi (1724 kPa).
SES Enser Engineering, Via Carolina Romani 8/10, 20091 Bresso (MI), Italy
Sprinkler System. Double interlocked, uses a deluge valve controlled by an electric release system and pneumatic system pressure. Consists of 3, 4, 6, 8 in. NPS FARES Model F799-DG04K automatic water control valve, Model 284-08 3-way pilot, Model 377 pneumatic actuator, Model 379 air reset unit, Model 375 flow release pilot, Skinner Model 73218BN4UNLVN0C111C2 or ASCO Model 8210G207, 24 V dc solenoid valve, compatible FM Approved automatic release control panel with appropriately sized battery to provide 90 hours of emergency power. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Sprinkler System. Double interlocked, uses a deluge valve controlled by an electric release system and pneumatic system pressure. Consists of automatic water control valve Model A, 3, 4, 6 in. NPS with 332 in. diaphragm chamber orifice, Skinner LV2LBX25 or 73218BN4UNLVNOC111C2 solenoid valves, Star Model AA-R or Tyco Model DP-1 dry pilot actuator, compatible FM Approved automatic release control panel with appropriately sized battery to provide 90 hours of emergency power; United Electric Control Co Models J54-8300 and J54-8295 pressure alarm switches; Star Model A manual control station. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping. Sprinkler System. Double interlocked, uses a deluge valve controlled by an electric release system and pneumatic system pressure. Consists of automatic water control valve Model A-1, 3, 4, 6 in. NPS with 332 in. diaphragm chamber orifice, Skinner 73212BN4TNLVNOC322C2 solenoid valves, Tyco Model DP-1 dry pilot actuator, compatible FM Approved automatic release control panel with appropriately sized battery to provide 90 hours of emergency power; United Electric Control Co Models J54-8300 and J54-8295 pressure alarm switches; Tyco Model MC-1 manual control station. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping.
FM Approvals
1-116
solenoid valve will be rated at 175 psi (1205 kPa). Systems using a Skinner Model No. 73212BN4TNLVN0C322C2 solenoid valve will be rated at 250 psi (1725 kPa). Only FM Approved fixed temperature heat sensitive devices shall be used in the release system and in the sprinkler piping. Refrigerated Area Sprinkler Systems, with the DV-5 water control valve, are available factory assembled vertically inside the Model DV-5 Red-E Cabinet in sizes 112, 2, 3, 4, and 6 in. NPS. The Red-E cabinet and assembled system components comprise an integrated fire protection system which is assembled and tested at the factory. The cabinet contains: the system shutoff valve, Model DV-5 deluge valve, 24 Vdc battery backup, and an electrical control/release panel for the solenoid valve release. The control panel is prewired to the switches for the alarm, supervisory, and trouble functions. Installation requires the connection to the water inlet inlet and outlet, main drain, electrical power supply, and the alarm and detection circuits. A built-in air compressor and air maintenance device provides controlled system air pressure.
Optional system components include: System Sensor EPS10-2 alarm line pressure switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve
Series 769 Firelock NXT Double-Interlocked Valve with Electric/Pneumatic Release. Sizes 212, 3, 4, 6 and 8 in. NPS. Grooved inlet and grooved outlet, installed vertically. The system rated working pressure is 300 psi (2070 kPa). Major trim components consist of the following: Series 776 Low Pressure Pneumatic Actuator with Auto Vent pressure operated system air pressure relief valve Series 753-E normally closed solenoid valve Series 749 Auto Drain pressure operated piston charge line water relief valve Series 729 alarm line Drip Check Valve Series 748 anti-flood Ball Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Series 768 Air Manifold Assembly with integral restrictor/screen/anti-flood ball check valve Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: Regulated Air Maintenance Trim Assemblies Series 757 or 757-P with pressure switch Series 746-LPA Accelerator System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 system air pressure supervisory switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
Series 769 Firelock NXT Double-Interlocked Valve with Electric/Pneumatic Release Sizes 112, 2, 212, 3, 4, 6, and 8 in. NPS. Grooved inlet and grooved outlet, installed vertically. The system rated working pressure is 300 psi (2070 kPa). Major trim components consist of the following: Series 767 Electric/Pneumatic Actuator; an Auto Vent pressure operated system air pressure relief valve Series 749 Auto Drain pressure operated piston charge line water relief valve
FM Approvals
1-117
Series 729 alarm line Drip Check Valve Series 748 anti-flood Ball Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Series 768 Air Manifold Assembly with integral restrictor/screen/anti-flood ball check valve Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly.
Optional system components include: Regulated Air Maintenance Trim Assemblies Series 757 or 757-P with pressure switch Series 746-LPA Accelerator System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 system air pressure supervisory switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
Series 769 Firelock NXT Double-Interlocked Valve with Pneumatic/Pneumatic Release. Sizes 112, 2, 212, 3, 4, 6, and 8 in. NPS. Grooved inlet and grooved outlet, installed vertically. The system rated working pressure is 300 psi (2070 kPa). Major trim components consist of: the following: Series 798 Pneumatic/Pneumatic Actuator with Auto Vent pressure operated system air pressure relief valve Series 749 Auto Drain pressure operated piston charge line water relief valve Series 729 alarm line Drip Check Valve Series 748 anti-flood Ball Check Valve Series 768 alarm line 3-Way Ball Valve for alarm/test/off Two Series 768 Air Manifold Assemblies with integral restrictor/screen/anti-flood ball check valve Water Supply Main Drain/Flow Test Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections System Main Drain Valve, size 2 in. with three 12 in. NPT outlets for gage and drain connections Series 752 piston charge line Strainer/Check Valve/Restrictor assembly
Optional system components include: Regulated Air Maintenance Trim Assemblies Series 757 or 757-P with pressure switch Two Series 746-LPA Accelerators System Sensor EPS10-2 alarm line pressure switch System Sensor EPS40-2 system air pressure supervisory switch Series 755 Manual Pull Station Series 760 Water Motor Alarm Series 705W water supply butterfly shutoff valve.
All refrigerated area sprinkler systems discussed above offer the Series 757-P Air Maintenance Trim Assembly as an option. It is used to control the system air pressure on all refrigerated area sprinkler systems, by controlling small air compressors which do not have pressure control switches. All refrigerated area sprinkler systems discussed above offer the Series 75-W Water Column Drain Kit as an option, which automatically drains water from the sprinkler systems and subsequently reseals to maintain air pressure in the system piping. All refrigerated area sprinkler systems discussed above offer the Series 75-B supplemental alarm valve as an option recommended for systems where continuous flow to the alarm port, which supplies flow to the water motor alarm, must be positively maintained. All the 112, 2, 212, 3, 4, and 6 in. NPS Refrigerated Area Sprinkler Systems discussed above are available factory assembled in the Victaulic Series 745 Fire-Pac enclosure, a cabinet containing all system components and accessories, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. The Series 745 Fire-Pacs may be connected to Notifier AFP-200 Programmable Analog Fire control with software no. AFP2R2.42 or System Sensor PDRP-1001 fire control with operating system firmware revision level A. The AFP-200 control contains FMM-1 Module with a signaling line circuit which can be configured to meet Styles 4, 6 or 7 wiring performance as described in NFPA72. The addressable panels utilize model XP-10M module which may be configured at the factory to monitor the Fire-Pac cabinet and valve station. Optional LED Interface Module 4XTM and Relay Module RTM-8 provide outputs for auxiliary applications.
FM Approvals
1-118
Model H-1 or R-1 pneumatic actuator; Model C pressure-operated relief valve (PORV); dehydrator P/N 01285A; Model D-2 air pressure maintenance device; compatible FM Approved solenoid valve and automatic release panel equipped with appropriately sized battery to provide required 90 hours of emergency power; available with Speed Control Assembly trim option; FM Approved rubber-faced check valve. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping. Model E-3 and E-4, 112 in. NPS and Model E-1 and E-2, 2 in. NPS available with screwed connections only. Model E-1 or E-2, 3, 4, 6 in. NPS available with flanged inlet and outlet or flanged inlet and cut-grooved outlet connections. Model F-1 and F-2, in-line globe water control valves, 8 in. NPS, are available with grooved by grooved end connections or flanged by flanged end connections. Model F-1 or F-2 in-line globe water control valves, 3, 4, and 6 in. NPS, are available with grooved by grooved, flanged by flanged end, or flanged inlet by grooved outlet connections. Model F-1 or F-2 in-line globe water control valves, 112, 2 and 212 in. NPS, are available with grooved by grooved, or screwed end connections. Rated working pressure is 250 psi (1725 kPa). Previous system ratings are dependent on the solenoid valve used. See table of related components shown under Automatic Water Control Valves. Sprinkler System. Double interlocked, Electric Pneu-Lectric, supervised dry system using a deluge valve controlled by electric release system and pneumatic system pressure. Consists of water control valve Model E-1 or E-2 in size 2, 3, 4 or 6 in. NPS or Model E-3 or E-4 in size 112 in. NPS or Model F-1 or F-2 in-line globe water control valves 112, 2, 212, 3, 4, 6 or 8 in. NPS; priming line including strainer, 0.063 in. (1.6 mm) dia. orifice and spring loaded check valve; Model C-1 or C-2 emergency release; for 10 psi (69 kPa) supervisory air system use Model 09471 dual SPDT pressure switches; for 30 psi (207 kPa) supervisory air system use Model 09473 dual SPDT pressure switches; Model C-1 pressure-operated relief valve (PORV) including conventional deluge trim; dehydrator P/N 01285A; Model D-2 air pressure maintenance; compatible FM Approved solenoid valve and automatic release control panel, equipped capable of cross zoned operation with FM Approved compatible pressure switch and heat actuated device and appropriately sized battery to provide required 90 hours of emergency power; available with Speed Control Assembly trim option; available with Easy Trim option utilizing Model A-1 or A-2 pressure shut-off valve (PSOV); FM Approved rubber-faced check valve. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and sprinkler piping. Model E-3 and E-4, 112 in. NPS and Model E-1 and E-2, 2 in. NPS available with screwed connections only. Model E-1 or E-2, 3, 4, 6 in. NPS available with flanged end connections or flanged inlet and cut-groove outlet connections. Model F-1 and F-2, 3, 4, 6, 8 in. NPS available with grooved end connections or flanged end connections or flanged inlet and grooved outlet end connections. Model F-1 or F-2 in-line globe water control valves, 112, 2 and 212, in. NPS, are available with grooved by grooved, or screwed end connections. Rated working pressure is 250psi (1725 kPa). The rated working pressure of the Electric/Pnue-Electric refrigerated area sprinkler system is dependent on the solenoid valve used. See table of related components shown under Automatic Water Control Valves. Refrigerated Area Sprinkler Systems are available factory assembled in the Viking Total Pac enclosure with in sizes 112 through 6 in. NPS, with electric/pneumatic, pneumatic/pneumatic, and electric-pneumatic/electric releases. The Total Pac enclosure and assembled valve systems comprise an integrated fire protection system which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Sprinkler System. Sure Fire Fail/Safe double interlocked, supervised dry system using a deluge valve controlled by a electric release system and pneumatic system pressure. Consists of angle type water control valves Model E-1 or E-2, in sizes 2, 3, 4, and 6 in. NPS, or Model E-3 or E-4 in size 112 in. NPS; or in-line Model F-1 or F-2 in-line globe type water control valves in sizes 112, 2, 212, 3, 4, 6 and 8 in. NPS; strainer; restricted orifice with 0.063 in. (1.6 mm) dia. orifice; Model B-1 release control panel, with an appropriately sized battery to provide 90 hours of emergency power, equipped capable of cross zoned operation with FM Approved compatible pressure switch and heat actuated device; FM Approved solenoid valves include the normally open Viking Model 11595, the normally closed Viking Model 11591, the normally open explosion proof Viking Model 11596, the normally closed explosion proof Viking Model 11592; or N.C. Solenoid Valve, Viking P/N 11591 and N.O. Solenoid Valve, Viking P/N 13215 for 250 psi (1725 kPa) rated working pressure. Pneumatic actuators Model H-1 or R-1; Model C-1 or C-2 emergency releases; dual SPDT Model 09473 and single SPDT Model 09472 air supervisory switch; Model 09470, 09471 pressure switch; dehydrator P/N 01285A; Model D-2 air pressure maintenance device; available with Easy Trim option, utilizing a Model A-1 or A-2 pressure shut-off valve (PSOV); trim available in galvanized, brass or stainless steel piping; FM Approved rubber-faced System check valve. Only FM Approved fixed temperature, heat sensitive devices shall be used in the release system and in the sprinkler piping. Model F-1 and F-2 valves are capable of vertical installation. Same valve end connections as noted above. Rated working pressure 250 psi (1725 kPa). Piping above the riser check valve contains supervisory air pressure at 30-50 psi (205-345 kPa) to monitor system integrity. If the system piping is damaged, the low air pressure alarm is activated and the normally open solenoid valve is activated closed, but the main water control valve does not trip, and no water flows into the sprinkler system until the heat detection device is actuated. This causes the normally closed solenoid valve to open which activates the control valve and water flow is supplied to the sprinkler system. Also the low air supervisory switch and the heat detection device must activate before the system control valve will open and supply water to the sprinkler system. In loss of power condition, the system operates from system supervised air and the pneumatic actuator. Refrigerated Area Sprinkler Systems, which utilize the angle type main water control valves, are available factory assembled in the Viking Total Pac2 enclosure, a second generation enclosure which replaces the Total Pac. The Total Pac2 is available in several configurations: 1) the system fully enclosed on legs with an access door and a built in electrical control panel (when electric activation required); 2) the valve system fully enclosed on legs with an access door and a remote control panel; 3) the valve system assembled to a skid and used with a remote control panel. All Refrigerated Area Sprinkler Systems are available with TrimPac trim package.
FM Approvals
1-119
A very important feature of the multicycle sprinkler system is its effect toward the reduction of the closed-valve, catastrophic fire. With the multicycle system, the manual sprinkler control valve would not have to be closed except in the very infrequent case of major maintenance involving a certain small section of the overall system. Unless otherwise noted in the listing, this system has 175 psi (1205 kPa) rated working pressure.
The Viking Corp, 210 N Industrial Park Rd, Hastings MI 49058
Firecycle II System. Consists of the Model H-1, H-2, H-3 or H-4 main water control valve in size 112 in. NPS or the Model H-1 or H-2 main water control valve, in sizes 2, 3, 4 or 6 in. NPS or the Model J-1 and J-2 main water control valve in size 4, 6, 8 in. NPS and accessories; FM Approved check valve (Viking Models D-2 or equivalent having rubber-faced clapper); Model D-1 control panel and series circuit of P/N 04625-B, 140F (60C); 04626-B, 160F (71C); 04627-B, 190F (88C); 04628-B, 225F (107C) heat-actuated fire detectors connected by Firecycle aluminum clad fire alarm cable; Model C-1 valve trim box; Model C-1 emergency release (optional); Model A-1 battery charger/ power supply P/N 03982C or P/N 04362C; available with Speed Control Assembly trim option; FM Approved waterflow alarm. Model H-1 or H-2, 3, 4, 6 in. NPS water control valve available with flanged inlet and outlet or flanged inlet and cut-grooved outlet connections. Model H-1, H-2, H-3 and H-4, size 112 NPS and Model H-1 and H-2, size 2 in. NPS water control valve available with screwed connections only. Model J-1 and J-2 main water control valve in size 4, 6, 8 in. NPS available with grooved end connections. Firecycle II Sprinkler Systems rated at 175 psi (1205 kPa). The electric equipment controls the mechanical operations necessary to start automatically and stop water flow from those standard sprinklers opened by fire. The temperature rating of the detector should be lower than the rating of its adjacent sprinklers. Power failure and fire alarm are signaled automatically. System is powered by line voltage and maintains charge in 24 V emergency battery supply (90 hr standby capability). Piping above riser check valve normally contains supervisory air pressure at 10-15 psi (70-105 kPa). Detectors are spaced according to ceiling construction and possible obstruction conditions, but should not exceed 40 ft (12 m) for P/N 04625-B or 25 ft (8 m) for P/Ns 04626-B, 04627-B and 04628-B; their location should be within 18 in. (457 mm) laterally of a sprinkler deflector except in low hazard occupancies. Sprinkler discharge continues for a timed interval (5 min. normally) after all normally closed contact detectors have been restored; this interval should be extended to 15 min. where persistent localized fire is anticipated. The manufacturers instructions and appropriate sprinkler installation rules should be followed in Firecycle installation, testing and maintenance. The Firecycle III Model E-1 Control Panel automatically starts and stops waterflow to the sprinkler system in response to the on-off cycling of the heat responsive detectors. Piping above the riser check valve contains supervisory air pressure at 25-30 psi to monitor system integrity. If the system piping is damaged, the low air pressure alarm is activated, but the main water control valve does not trip and no water flows from the sprinkler system. Firecycle III System. Consists of Model H-1 or H-3, 112, 2, 3, 4 or 6 in. NPS main water control valve or Model J-1 or J-2, 112, 2, 212, 3, 4, 6, 8 in. NPS main water control valve and accessories; FM Approved check valve (Viking Model E-1 or equivalent having rubber-faced clapper); Firecycle III Control Panel E-1, Viking P/N 10751 and 10752; Firecycle III Model B heat-actuated fire detectors for 140F (60C), P/N 04625-B; 160F (71C), 04626-B; 190F (88C), P/N 04627-B; 225F (107C), P/N 04628-B; Firecycle aluminum clad detector cable, P/N 04632-A; Model C-1 emergency release; 90-hour, 17 A-H battery back-up power supply capable of being recharged in 48 hours, P/N A-09867; N.C. Solenoid Valve, Viking P/N A-08408 and N.O. Solenoid Valve, Viking P/N A-08407 for 175 psi (1205 kPa) rated working pressure. N.C. Solenoid Valve, Viking P/N 11591 and N.O. Solenoid Valve, Viking P/N 11595 for 250 psi (1725 kPa); or N.C. Solenoid Valve, Viking P/N 11591 and N.O. Solenoid Valve, Viking P/N 13215 for 250 psi (1725 kPa) rated working pressure. FM Approved 30 psi Supervisory Pressure Switch; FM Approved 5 psi Pressure Alarm Switch; Pneumatic Actuator, Viking Model H-1; Pressure Operated Relief Valve (P.O.R.V.), Viking Model C-1; Automatic Drip Check Valve, Viking Model D-1. Available with TrimPac trim package. A restricted and regulated air supply is recommended by the manufacturer. An equivalent FM Approved air pressure maintenance device may be used. Model J-1 and J-2, in-line globe water control valves, 8 in. NPS, are available with grooved by grooved end connections or flanged by flanged end connections. Model J-1 or J-2 in-line globe water control valves, 3, 4, and 6 in. NPS, are available with grooved by grooved, flanged by flanged end, or flanged inlet by grooved outlet connections. Model J-1 or J-2 in-line globe water control valves, 112, 2 and 212 in. NPS, are available with grooved by grooved, or screwed end connections. The Firecycle III Model E-1 Control Panel automatically starts and stops waterflow to the sprinkler system in response to the on-off cycling of the heat responsive detectors. Piping above the riser check valve contains supervisory air pressure at 25-30 psi to monitor system intergrity. If the system piping is damaged, the low air pressure alarm is activated, but the main water control valve does not trip and no water flows from the sprinkler system. The temperature rating of the detector should be lower than the rating of its adjacent sprinklers. Power failure and fire alarm are signaled automatically. System is powered by line voltage (110/220/240 V ac) and operates (cycles) normally with the 24 V emergency battery back-up system (90 hr standby capability). Detectors are spaced according to ceiling construction and possible obstruction conditions, but should not exceed 40 ft (12 m) for P/N 04625-B or 25 ft (8 m) for P/N 04626-B, 04627-B and 04628-B; their location should be within 18 in. (457 mm) laterally of a sprinkler deflector except in low hazard occupancies. Sprinkler discharge continues for a timed interval (5 min. normally) after all normally closed contact detectors have been restored; this interval should be extended to 15 min. where persistent localized fire is anticipated. The manufacturers instructions and appropriate sprinkler installation rules should be followed in Firecycle III installation, testing and maintenance. FireCycle III and FireCycle III-OH Sprinkler Systems are available factory assembled in the Viking Total Pac enclosure in sizes 112 through 6 in. NPS, when utilizing the angle type main water control valves, Models H-3 and H-1, in both single-interlock preaction and cycling wet pipe configurations. The Total Pac enclosure and assembled valve systems comprise an integrated fire protection system which is assembled and tested at the factory, and requires only the connection to the water supply inlet, water outlet (to system), main drain, the alarm and detection connections, and the electrical power supply. Firecycle III-OH System. Single Interlock Preaction System. Consists of Model H-3 main water control valve, size 112 NPS, or Model H-1 main water control valve, sizes 2, 3, 4 or 6 in. NPS, or Models F-1 or F-2 main water control valves, sizes 4 and 6 in., or Models J-1 or J-2 main water control valves, sizes 112, 2, 212, 4, 6, and 8 in. NPS; Viking Model F-1 riser check valve, sizes 3, 4, 6, and 8 in., or Model L-1 riser check valve, sizes 112 and 2 in. having a rubber-faced clapper); Firecycle III Control Panel E-1, Viking P/N 10751 and 10752; Firecycle III-OH heat detectors are self-restoring, normally closed, heat-actuated switches. There are two types: Viking Model C surface mount and Viking Model C flush mount. The surface mount is attached directly to a ceiling or to a ceiling mounted standard octagonal electrical box, and the detector wire in conduit is exposed below the ceiling. The flush mount detector is attached to a standard octagonal electrical box recessed in the ceiling, and the detector wire is concealed above the ceiling. The detector wire is Viking P/N 09954, NEC FPL rated wire, 16 gage, 2 conductor, 2 hour rated (in conduit or equal), or Viking P/N 11988, NEC FPL rated wire, 18 gage, 2 conductor, 2 hour rated (in conduit or equal), or Viking P/N 04236A, aluminum clad wire installed behind proper rated construction. Model C normally closed heat-actuated flush mounted fire detectors for Ordinary Hazard applications: 140F (60C), P/N 11723; 160F (71C), P/N 11724; 190F (88C), P/N 11725; 225F (107C), P/N 11726; Model C normally closed heat-actuated surface mounted fire detectors for Ordinary Hazard applications: 140F (60C), P/N 11727; 160F (71C), P/N 11728; 190F (88C), P/N 11729; 225F (107C), P/N 11730. Model C-1 emergency release; 90-hour, 18 A-H battery back-up power supply capable of being recharged in 48 hours, P/N A-09867. For 250 psi rated working pressure, N.C. solenoid valve, Viking P/N 11591 and N.O. solenoid valve, Viking P/N 11596; or N.C. Solenoid Valve, Viking P/N 11591 and N.O. Solenoid Valve, Viking P/N 13215 for 250 psi (1725 kPa) rated working pressure; 30-50 psi adjustable supervisory pressure Switch; 5 psi Pressure Alarm Switch; Pneumatic Actuator, Viking Model H-1; Pressure Operated Relief Valve (P.O.R.V.), Viking Model C-1; Automatic Drip Check Valve, Viking Model D-1. Available with TrimPac trim package. A restricted and regulated air supply is recommended by the manufacturer. The Firecycle III-OH On-Off Preaction Sprinkler System piping has supervisory system air pressure
FM Approvals
1-120
(minimum 30 psi, for 20 psi water supply pressure, up to 50 psi, for 250 psi water supply pressure) to monitor system integrity. If the system piping is damaged or a sprinkler activates, the low air pressure alarm is activated, but the main water control valve does not trip and no water flows to the sprinkler system. When the heat detection system has been activated, the main water control valve opens and water will flow out any open sprinklers. The Firecycle III Model E-1 Control Panel automatically starts and stops water flow to the sprinkler system in response to the on-off cycling of the heat responsive detectors. The heat detectors open when the detectors are exposed to the heat of the fire and close when the detector cools below its set point. Sprinkler discharge continues for a timed soakinterval (5 min normally) after all normally closed contact detectors have closed. This interval should be extended to15 minutes where persistent localized fire is anticipated. The on-off cycling of the heat responsive contacts controls the system solenoid valves which in turn control the opening and closing of the main water control valve. The temperature rating of the detectors should be lower than the rating of its adjacent sprinklers. Power failure and fire alarms are signaled automatically. System is powered by line voltage (110/220/240 VAC) and operates (cycles) normally with the 24 VDC emergency battery back-up system (90 hr standby capability). Detectors are spaced according to ceiling construction and possible obstruction conditions, but should not exceed 40 ft (12 m) for P/N 11727 or 25 ft (8 m) for P/N 11728, 11729 and 11730; their location should be in accordance with NFPA 72E. The manufacturers instructions and appropriate sprinkler installation rules should be followed in Firecycle III-OH installation, testing and maintenance. The FireCycle III System-OH is rated for 250 psi (1725 kpa) operating pressure. Firecycle III-OH Cycling Wet Pipe System. Consists of: Model H-3 main water control valve, size 112 NPS, or Model H-1 main water control valve, sizes 2, 3, 4 or 6 in. NPS, or Models J-1 or J-2, 112, 2, 212, 3, 4, 6 and 8 in. NPS main water control valve and accessories; Water Flow Switch and system Drain Valve down stream of control valve. Firecycle III Control Panel E-1, Viking P/N 10751 and 10752; Firecycle III-OH heat detectors are self-restoring, normally closed, heat-actuated switches. There are two types: Viking Model C surface mount and Viking Model C flush mount. The surface mount is attached directly to a ceiling or to a ceiling mounted standard octagonal electrical box, and the detector wire in conduit is exposed below the ceiling. The flush mount detector is attached to a standard octagonal electrical box recessed in the ceiling, and the detector wire is concealed above the ceiling. The detector wire is Viking P/N 09954, NEC FPL rated wire, 16 gage, 2 conductor, 2 hour rated (in conduit or equal), or Viking P/N 11988, NEC FPL rated wire, 18 gage, 2 conductor, 2 hour rated (in conduit or equal), or Viking P/N 04236A, aluminum clad wire installed behind proper rated construction.; Model C normally closed heat-actuated flush mounted fire detectors for Ordinary Hazard applications: 140F (60C), P/N 11723; 160F (71C), P/N 11724; 190F (88C), P/N 11725; 225F (107C), P/N 11726; Model C normally closed heat-actuated surface mounted fire detectors for Ordinary Hazard applications: 140F (60C), P/N 11727; 160F (71C), P/N 11728; 190F (88C), P/N 11729; 225F (107C), P/N 11730; Model C-1 emergency release; 90- hour,18 A-H battery back-up power supply capable of being recharged in 48 hours, P/N A-09867. For 250 psi rated working pressure, N.C. solenoid valve, Viking P/N 11591 and N.O. solenoid valve, Viking P/N 11596; or N.C. Solenoid Valve, Viking P/N 11591 and N.O. Solenoid Valve, Viking P/N 13215 for 250 psi (1725 kPa) rated working pressure. The Firecycle III-OH Cycling Wet System in the normal set condition has the main water control valve in the open position, the sprinkler piping is filled with water, and water will flow from any activated sprinklers. The Firecycle III Model E-1 Control Panel automatically starts and stops water flow to the sprinkler system in response to the on-off cycling of the heat responsive detectors. The heat detectors open when the detectors are exposed to the heat of the fire and close when the detector cools below its set point. Sprinkler discharge continues for a timed soakinterval (5 min normally) after all normally closed contact detectors have closed. This interval should be extended to 15 minutes where persistent localized fire is anticipated. The on-off cycling of the heat responsive contacts controls the system solenoid valves which in turn control the opening and closing of the main water control valve. The temperature rating of the detectors should be lower than the rating of its adjacent sprinklers. Power failure and fire alarms are signaled automatically. System is powered by line voltage 110/220/240 V ac) and operates (cycles) normally with the 24 VDC emergency battery back-up system (90 hr standby capability). Detectors are spaced according to ceiling construction and possible obstruction conditions, but should not exceed 40 ft (12 m) for P/N 11727 or 25 ft (8 m) for P/N 11728, 11729 and 11730; their location should be in accordance with NFPA 72E. The manufacturers instructions and appropriate sprinkler installation rules should be followed in Firecycle III-OH installation, testing and maintenance. The FireCycle III System-OH is rated for 250 psi (1725 kpa) operating pressure. Multicycle On-Off Sprinkler Systems, which utilize the angle type main water control valves, are available factory assembled in the Viking Total Pac2 enclosure, a second generation enclosure which replaces the Total Pac. The Total Pac2 is available in several configurations: 1) the system fully enclosed on legs with an access door and a built in electrical control panel (when electric activation required); 2) the valve system fully enclosed on legs with an access door and a remote control panel; 3) the valve system assembled to a skid and used with a remote control panel. Available with TrimPac trim package.
FM Approvals
1-121
Unimode-640 Fire Alarm Control Panel. Basic system consists of the ADT-CPU-640 module with internal power supply. 120 V ac primary system provides four notification appliance circuit/releasing circuit outputs rated at 24 V dc 2.5 A plus two 24 V dc 1.25 A (total) auxiliary outputs. Total power output is 6 A in alarm, 3A in standby. Release circuit requires REL 2.2K end-of-line device for supervision. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Transmitter Module (TM-4) provides a local energy municipal tie for auxiliary protective signaling. Standby battery (24 V dc up to 60 AH) provides 90 hour standby operation. See control panel description under LOCAL PROTECTIVE SIGNALING.
Buckeye Fire Equipment Co, 110 Kings Road, King Mountain NC 28086
Shield-SZ DipSwitch Programmable Fire Alarm Control Panel using Version 1.00 firmware; P/N SZ-120-2R (110 V ac) and SZ-240-2R (240 V ac). The system may include SZ120-0c (110 V ac) or SZ250-0c (208 or 240 V ac) enclosures with transformer, SZ200-17 (17 AH) battery assembly, SZ101 controller, SZ400 Class A Input Module, and SZ440 Relay module. In the sprinkler mode, the SZ101 Controller Card provides two initiating device circuits (capable of cross-zone, sequential alarm or single detector release) for fire detection, one waterlow circuit; one supervisory circuit, all of which are Class B Style A. Initiating device circuits must be converted to Class A Style D with Class A input module SZ400 for sprinkler release. In addition, the controller provides three notification circuits (all Class B, Style Y); one alarm relay (non-programmable); one trouble relay (non-programmable), and one solenoid releasing circuit for activation of compatible 24 V solenoid valves. For FM Approved combinations of solenoid and deluge water valves refer to AUTOMATIC WATER CONTROL VALVES.
CHEMETRON Fire Systems, 4801 Southwick Dr, 3rd Floor, Matteson IL 60443
Micro 1001 with operating system Firmware Revision Level A. Including a zone relay module. Panel provides four input circuits: one detector; one manual release/detector; one waterflow; one supervisory and four output circuits; one alarm/waterflow bell; one waterflow/
FM Approvals
1-122
supervisory bell; one release; one supervisory bell/release. In addition, one regulated and one unregulated 24 V auxiliary power output; one alarm and one trouble relay output are provided. Combined load for all external devices not to exceed 2.25 A. Field programmable using dip switches for either cross zone or dual zone. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models T8210A107, R8210A107, 8210A107 and Skinner Model LV2LBX25 and solenoid for Star Sprinkler Model D deluge valve. For FM Approved combinations of solenoid and water control valves, refer to AUTOMATIC WATER CONTROL VALVES. In the event of primary power failure, battery packs (24 V dc, 12, 15 AH) are suitable for 90 hours of standby power. Fire Alarm Control. Micro-200I Analog Fire Panel. Programmable control (see listing under LOCAL PROTECTIVE SIGNALING). Contains a signaling line circuit with cross-zone capability and four indicating appliance/release circuits. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107, Skinner Model LV2LBX25 and solenoid for Star Sprinkler Model D deluge valve. For FM Approved combinations of solenoid and water control valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby battery packs (24 V dc, 7 to 12 AH) provide 90 hours standby operation. MICRO-640I Fire Alarm Control Panel. Basic system consists of the MICRO-640-CPU module with internal power supply. 120 V ac primary system provides four notification appliance circuit/releasing circuit outputs rated at 24 V dc 2.5 A plus two 24 V dc 1.25 A (total) auxiliary outputs. Total power output is 6 A in alarm, 3A in standby. Release circuit requires REL 2.2K end-of-line device for supervision. Release circuit can be provided via FCM-1 module and/or XP5-C and XP5-M Transponders. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Transmitter Module (TM-4) provides a local energy municipal tie for auxiliary protective signaling. Standby battery (24 V dc up to 60 AH) provides 90 hour standby operation. See control panel description under LOCAL PROTECTIVE SIGNALING.
FM Approvals
1-123
55-047 Supervised Control Module (SCM) to provide peer-to-peer digital communication protocol between the conventional notification appliance circuits and the CyberCat signaling line circuit. In addition, the SCM operates solenoids rated up to 2 Amps @ 24 V dc. Controller is also compatible with P/N 55-052 and P/N 55-053 Releasing Control Modules (RCM). The RCM supervises solenoid of a sprinkler water control valve and is connected to the controller SLC loop. For Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. 24 V dc batteries rated 18-75 AH are available to provide 90 hours of emergency operation. [See further description under LOCAL PROTECTIVE SIGNALING]. Cheetah Xi Fire Alarm Control System (P/N 10-068). Programmable addressable system consisting of P/N 10-2542 Cheetah Xi Controller with V1.30, within P/N 10-2541(R/G) enclosure, and power supply with transformers P/N 02-10881 (120 Vac) or P/N 02-10882 (240 Vac). Controller connects with p/ns 55-042 or 55-047 Supervised Control Module (SCM) to provide peer-to-peer digital communication protocol between the conventional notification appliance circuits and the CyberCat signaling line circuit. In addition, the SCM operates solenoids rated up to 2 Amps @ 24 V dc. In addition, Release Control Module p/ns 55-042 or 55-047 operates solenoids rated up to 2 Amps @24 V dc. For Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. 24 V dc batteries rated 18-75 AH are available to provide 90 hours of emergency operation. [See further description under LOCAL PROTECTIVE SIGNALING]. Cheetah Xi 50 and Cyber Cat 50 Fire Alarm Control units are programmable addressable systems consisting of [P/N 10-2622, P/N 10-2620], respectively Controller with V3.00, within P/N 10-2623(R/G) and 10-2621 (R/B) enclosure, and power supply with transformers P/N 02-10881. Controller connects with p/ns 55-042 or 55-047 Supervised Control Module (SCM) to provide peer-to-peer digital communication protocol between the conventional notification appliance circuits and the signaling line circuit. In addition, the SCM operates solenoids rated up to 2 Amps @24V dc. In addition, Release Control Module [p/ns 55-042 or 55-047] operates solenoids rated up to 2 Amps @24 V dc. For Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. 24 V dc batteries rated 18-75 AH are available to provide 90 hours of emergency operation. [See further description under LOCAL PROTECTIVE SIGNALING]. Rhino programmable control includes (DCM) detection and control module P/N 10-2141 (110 V ac) or -2144 (220 V ac) which are capable of cross-zone detection. Compatible with ASCO Models 8210A107, R8210A107, T8210A107 and Skinner Model LV2LBX25 and 73218BN4UNLVNOC111C2 solenoid valves. For FM Approved combinations of solenoid water control valves, refer to AUTOMATIC WATER CONTROL VALVES. 24 V dc batteries rated 17-33 AH are available to provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) Shark Fire Alarm Control. Analog Addressable Control P/N 10-056-1 with firmware level 2.00. The Detector Board (P/N 10-2323) provides one signaling line circuit (SLC) which meets NFPA Style 4, 6, or 7 wiring performance. Two notification appliance circuits (Class A or B) Style Y, or Z are provided. Each NAC is rated for 1.5 Amps output and can control one solenoid each. Solenoid Series Impedance device P/N 10-2360 must be used when connecting a solenoid to the NAC circuit. Optional Addressable NAC Module P/N 55-038 (which requires a separate 24 V dc power to operate) provides a 2 A, 30 V dc output for a solenoid valve. The output circuit is supervised using a 47K ohm end of line resistor. 24 V dc batteries rated 7-65 AH are available to provide 24 hours of emergency operation. For FM Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. [For specific details on this system see LOCAL PROTECTIVE SIGNALING].
FM Approvals
1-124
for either cross zone or dual zone operation. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107, Skinner Model LV2LBX25, and solenoid for Star Sprinkler Model D deluge valve. For FM Approved combinations of solenoid and water control valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby battery packs (24 V dc, 12 and 15 AH) provide 90 hours of standby operation. See LOCAL PROTECTIVE SIGNALING listing for other FM Approved modules.
GE Security Inc, 8985 Town Center Pkwy, Bradenton FL 34202 Mirtone, 8985 Town Center Pkwy, Bradenton FL 34202
Automatic Release. EST2 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 24 AH capacity to provide the required 90 hours of standby operation. Automatic Release. EST3 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 65 AH capacity to provide the required 90 hours of standby operation. Automatic Release. MIR-2 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via GSA-REL releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 24 AH capacity to provide the required 90 hours of standby operation. Automatic Release. MIR-3 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via GSA-REL releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 65 AH capacity to provide the required 90 hours of standby operation. Automatic Release. Quick Start (QSC, QS1, and QS4) Fire Alarm Control. (See listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL releasing module which may use SIGA-APS auxiliary power supply. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 40 Ah capacity to provide the required 90 hours of standby operation. Quick Start (QSC, QS1, and QS4) Fire Alarm Control. Programmable control. Release circuits are via SIGA-REL releasing module which may use SIGA-APS auxiliary power supply. Used with model RELA-EOL polarized end of line resistor. Any one of the following manual releases, service disconnect switches, and abort stations must be used: model 276A-REL or 278A-REL manual release, RELA-SRV service disconnect, and RELA-ABT abort station. Standby batteries are available in up to 40 Ah capacity to provide the required 24 hours of standby operation. (See listing under LOCAL PROTECTIVE SIGNALING). Automatic Release. Quick Start (MIRQSC, MIRQS1, and MIRQS4) Fire Alarm Control. (See listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL releasing module which may use SIGA-APS auxiliary power supply. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 40 Ah capacity to provide the required 90 hours of standby operation.
FM Approvals
1-125
Automatic Release. XLS-1000 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via XLS-REL releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 65 AH capacity to provide the required 90 hours of standby operation. XLS140(E) Fire Alarm Control Panel. Basic system consists of the XLS140-CPU module with internal power supply. 120 V ac primary system provides four notification appliance circuit/releasing circuit outputs rated at 24 V dc 2.5 A plus two 24 V dc 1.25 A (total) auxiliary outputs. Total power output is 6 A in alarm, 3A in standby. Release circuit requires REL 2.2K end-of-line device for supervision. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Transmitter Module (TM-4) provides a local energy municipal tie for auxiliary protective signaling. Standby battery (24 V dc up to 60 AH) provides 90 hour standby operation. See control panel description under LOCAL PROTECTIVE SIGNALING.
FM Approvals
1-126
PEGAsys and PEGAsys LV programmable analog control panels equipped with CCM (single loop P/N 76-100008-701) Rev. CCMP82.3SL. PEGAsys ML is equipped with CCM (multi-loop P/N 76-200008-800) software Rev. CCMP82.3ML. All the controls are equipped with power supply module (P/N 76-100009-010) Rev. AA (configured for releasing service). Optional agent release module (P/N 76-100001-001) Rev. AD may be installed in the PEGAsys and PEGAsys ML. For Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. 24 V dc batteries rated 17-99 AH are available to provide 90 hours of emergency operation. (See description under LOCAL PROTECTIVE SIGNALING.) FENWALNET 6000 programmable analog addressable fire alarm control system with operating software Rev. 1.2.1. The control has one (Class A) Style 6, 7 or (Class B), Style 4 Signaling Line Circuit (SLC) that communicates with up to 255 analog addressable devices. The control also has two (Class A), Style Z or (Class B), Style Y Notification Appliance Circuits (NACs) rated 1.5 A @ 24 V dc. In addition, there are two releasing circuits rated 2.4A (max) @ 24 V dc for explosive initiators or solenoid-operated control heads and valves. Two more configurable output circuits are located on the mother board. The output circuits are used for connection to solenoid-operated control heads and valves, rated 2.4 A (max) @ 24 V dc. 24 V dc batteries rated 7 - 70 AH are available to provide 90 hours of emergency operation. [See further description under LOCAL PROTECTIVE SIGNALING.] ARIES programmable analog addressable fire alarm control system with operating software Rev. 1.2.1. The control has one (Class A) Style 6, 7 or (Class B), Style 4 Signaling Line Circuit (SLC) that communicates with up to 255 analog addressable devices. The control also has two (Class A), Style Z or (Class B), Style Y Notification Appliance Circuits (NACs) rated 1.5 A @ 24 V dc. In addition, there are two releasing circuits rated 2.4A (max) @ 24 V dc for solenoid-operated control heads and valves. Two more configurable output circuits are located on the mother board. The output circuits are used for connection to solenoid-operated control heads and valves, rated 2.4 A (max) @ 24 V dc. 24 V dc batteries rated 7-70 AH are available to provide 90 hours of emergency operation. [See further description under LOCAL PROTECTIVE SIGNALING]. Model AEGIS conventional fire alarm-suppression control panel consists of Rev. 1.0.0 operating software. The control panel has one manual release circuit rated 24 V dc, 10 mA. One abort circuit rated 24 V dc, 10 mA. There are two (Class B) Style Y, supervised, releasing circuits rated 2.4A (max) @ 24 V dc. The panel is provided with the releasing circuits for agent release or sprinkler release which will actuate a 24 V dc control head. For Approved combination of solenoid and water control valves, refer to Automatic Water Control Valve listings that follow. The panel is provided with standby battery capacity up to 68 AH to supply the required 90 hours of standby. (See control panel description under LOCAL SERVICE.) Model 732 conventional fire alarm-suppression control panel consists of Rev. 1.0.0 operating software. The control panel has one manual release circuit rated 24 V dc, 10 mA. One abort circuit rated 24 V dc, 10 mA. There are two (Class B) Style Y, supervised, releasing circuits rated 2.4A (max) @ 24 V dc. The panel is provided with the releasing circuits for agent release or sprinkler release which will actuate a 24 V dc control head. For Approved combination of solenoid and water control valves, refer to Automatic Water Control Valve listings that follow. The panel is provided with standby battery capacity up to 68 AH to supply the required 90 hours of standby. (See control panel description under LOCAL SERVICE.)
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Fire Alarm Control Panel FMZ 4100 GAB 32. Control uses software level 41EGB32X, P/N 902657. Control consists of the Line Card Rack (P/N 802599), which houses redundant CPU cards ZKR (P/N 895465), LED control card LEDAK (P/N 806271), Line cards LK and LKA (P/N 802551 and P/N 805424), Extinguishing Control card LO (P/N 837190), FTX Spark Test card (P/N 802540), SK Loop (MxLoop) card (P/N 902026), PC/printer interface card PC/DRUIF (P/N 832349), relay interface card IF2 (P/N 802538). The following cards connect directly to external modules and detectors: 8 relay card RK8 and RK8TQ (P/N 802587 and P/N 800843), line termination cards LAK8 and LAK8A (P/N 802563and P/N 806477), solenoid valve/monitored output cards MVA4F (P/N 853507), SAK2 loop (MxLoop) connection card (P/N 800255), spark test connection cards FTX-AK8 (P/N 806209). Logic power supply 5 V DC/2 A (P/N 837104), Logic power supply 15 V DC/2 A (P/N 837116), 24V/6amp power supply USVI-SE-210 (P/N 835193 )). Front panel FPTUL with 8x40 character LCD display (P/N 801215), LED panels F + S FPFUS (P/N 837189) and FPS for MxLoop devices indication only (P/N 851973), ground fault module MEM (P/N 800096). Control can provide up to 32/96/128 9V Class B detection input zones (maximum 32 detectors per one zone), the panel designations being FMZ 4100 GAB 32, FMZ 4100 GAB 96, and FMZ 4100 GAB 128 respectively. The latter use line termination cards LAK8 or LAK8A, 32/96/128 Zener groups for manual pull stations (open circuit) connections, 32/96/128 solenoid/notification appliances/monitored outputs via MVA4F cards. Compatible with the following initiating devices: DMX 3000, and 3003 manual stations, IMX 1001E ionization type smoke detector, rated IP 23, OMX 1001C, OMX 1111C photoelectric type smoke detectors, rated IP 23, WMX 1000 D60, WMX 1000 D90, WMX 1000 F60, rated IP 65 and WMX 1000 F90 (rated IP 65) heat detectors, FMX 3100, FMX3511, and UMX 3000 flame detectors, all rated IP 65 and FUX 3001(L1) spark detector, rated IP65. Series F60 and D60 heat detectors are combination of fixed temperature and rate-of-rise 140F (60C), while Series F90 and D90 heat detectors have triggering temperature ranging from 201F (94C) to 230F (110C). Spacing guide for D60 and D90 series heat detectors is 25 25 feet (7.6 7.6 m); while for F60 and F90 series it is 15 15 feet (4.6 4.6 m). Compatible with the following analog addressable devices via the MxLoop card: IMX50 ionization smoke detector, OMX50 photoelectric smoke detector, WMX50 D60 rate-of-rise heat detector: spacing guide for D60 series heat detectors is 30 30 feet (9.1m 9.1 m); DMX50/50F manual stations, SMX50 short circuit loop isolator, SUX50/50H contact monitoring module. For electric activated Deluge Sprinkler Systems, compatible solenoid valves are Minimax type 1/2-24 V/DC-2/2-Impulse, Minimax P/N 84 0131. Standby batteries 24 V, 65 AH provide 90 hours of emergency battery backup supply.
Mircom Technologies Ltd, 25 Interchange Way, Vaughan, Ontario L4K 5W3, Canada
FR-320-D (or blank)-R(or W) programmable fire alarm releasing control panel. ICAC-306 Class A Converter Module is required to configure the 6 initiating device circuits (IDC) for Class A, Style D operation. Provides 2 Class B releasing circuits. For deluge and preaction sprinkler
FM Approvals
1-127
system release, compatible solenoid valves include ASCO Models T8210A107, R8210A107, 8210A107. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Primary power 120 or 240 V ac. 24 V dc secondary supply consisting of batteries rated 10-26 AH provide required 90 hours of emergency operation. (See also description under AUTOMATIC RELEASES FOR EXTINGUISHING SYSTEMS AND OTHER FIRE PROTECTION EQUIPMENT.)
Pem-All Fire Extinguisher Corp, Div Pem Systems Inc, 39A Myrtle St, Cranford NJ 07016
PEM-2001 with operating system firmware revision level A. Including LED Interface Module (4XLM); Zone Relay Module (4XZM); Remote Annunciator (RZA-4X). Panel provides four input circuits: one detector; one manual release/detector; one waterflow; one supervisory and four output circuits: one alarm/waterflow bell; one waterflow/supervisory bell; one release; one supervisory bell/release. In addition one regulated and one unregulated 24 V auxiliary power output; one alarm and one trouble relay output are provided. Combined load for all extenal devices not to exceed 2.25 A. Field programmable using dip switches for either cross zone or dual zone. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25 and solenoid for Star Sprinkler Model D deluge valve. For FM Approved combinations of solenoid and water control valves, refer to AUTOMATIC WATER CONTROL VALVES. Transmitter Module (4XTM) provides a local energy municipal tie for auxiliary protective signaling. In the event of primary power failure, battery packs (24 V dc, 12, 15 AH) are suitable for 90 hours of standby operation.
FM Approvals
1-128
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
PFC Series 100R Fire Control Panel provides one Style D initiating circuit, one Style B non-latching supervisory device circuit, one voltage reversing Style Y indicating circuit rated 24 V dc, 500 mA, one voltage reversing releasing circuit rated 24 V dc, 1 A and one auxiliary power supply circuit rated 24 V dc, 15 mA. Compatible solenoid valves are ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries rated 8 AH provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) PFC Series 2000RC Fire Control Panel. (See also LOCAL PROTECTIVE SIGNALING.) Uses Firmware Version 1.1 with release circuit discharge times selectable (2 min. or continuous). Contains two signal initiating device circuits (field programmable for Style B or D operation), two signal indicating circuits, one manual releasing circuit, and one polarized releasing device circuit (24 V dc, 1 A continuous, 3 A momentary). The Style B and D initiating circuits are capable of cross-zone operation. Combined load of all external devices including signaling devices not to exceed 3 A. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25 and solenoid actuator in Star Sprinkler Model D deluge valve solenoid (P/N 5550). For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. In the event of primary power failure, standby battery packs (24 V dc, 6.5, 8, 10, 12, or 15 AH) are available for 90 hours emergency power. Model PFC-100RC Programmable Fire Control Panel. Provides one Style D alarm signal initiating device circuit, one Style B non-latching supervisory signal initiating device circuit, one voltage reversing Style Y notification appliance circuit rated 24 V dc, 500 mA, one voltage reversing releasing circuit rated 24 V dc, 1 A and one auxiliary power supply circuit rated 24 V dc, 15 mA. Compatible solenoid valves are ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries rated 8 AH provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) Model PFC-4410 and PFC-4410A Programmable Fire Control Panel, using software Rev. 3.5. Provides four Class B (Style B) alarm signal initiating device circuits, one Class B (Style B) supervisory signal initiating device circuit, four voltage reversing Class B (Style Y) programmable output circuits rated 24 V dc, 1 A, and one auxiliary power supply circuit rated 24 V dc, 50 mA with 12 AH standby batteries or 75 mA with 17 AH standby batteries. CA2Z Class A initiating device module required to convert two Class B initiating device circuits to Class A (Style D) operation. Up to two CA2Z modules may be used. Initiating device circuits are capable of cross-zone operation. Compatible solenoid valves are ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model 73218B4UNLVOC111C2. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries rated 12 and 17 AH provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) Model PFC-4410-RC and PFC-4410A-RC Fire Alarm Controls, using software Rev. 4.14. Provides four Class B (Style B) alarm signal initiating device circuits, one Class B (Style B) supervisory signal initiating device circuit, four voltage reversing Class B (Style Y) output circuits rated 24 V dc, 1 A, and one auxiliary power supply circuit rated 24 V dc, 200 mA. CA2Z Class A initiating device module required to convert two Class B initiating device circuits to Class A (Style D) operation. Up to two CA2Z modules may be used. Initiating device circuits are capable of cross-zone operation. Compatible solenoid valves are ASCO Models R8210A107, T8210A107, 8210A107, Skinner Models 73218B4UNLVOC111C2 and 73212BN4TNLVNOC322C2, and Viking Model HV-274-060-001. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries rated 12 AH provide the required 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.)
Pyrene Corp, 130 Esna Park Dr, Markham Ontario L3R 1E3 Canada
Fire Alarm and Extinguishment Control Panel Series 4000 configured with 40-3002 extinguishment module and other functional modules as dictated by the needs of the installation (see listing for the Series 4000 control under LOCAL PROTECTIVE SIGNALING for other functional modules). For deluge/preaction sprinkler system applications, the Series 4000 control must be configured to provide Class A (Style D) initiating circuits. Initiating circuits can be configured for cross-zone operation. Release device circuits are rated at 2 A. Compatible solenoid valves are ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries rated 16 AH are available to provide 90 hours emergency power.
FM Approvals
1-129
Series Triton RPA Addressable Control System. Analog control panel with Software Revision Level 3.03 using programmed Notification Appliance Circuits N3 or N4 on the Triton RPA SFI/O card. Each releasing appliance circuit must connect to a TEPG-US Model 430687 coil supervision module which in turn is connected to a compatible 24 V dc actuation device. Optional TEPG-US Model 430657 or 431193 Suppression Release Peripheral connects to the SLCNet circuit and to a notification appliance circuit from either the Triton RPA fire alarm control panel, or from the Triton EXT Notification Appliance Circuit Extender. This peripheral monitors the output releasing appliance circuit wiring for opens and shorts. Each releasing appliance circuit must connect to a TEPG-US Model 430687 coil supervision module which in turn is connected to a compatible 24 V dc solenoid or actuation device. For FM Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. SLCNet signaling line circuits must be configured for Class A, Style 6 wiring for this application. 24 Vdc batteries rated 25-50 AH are available to provide 90 hours of emergency operation. For battery requirements exceeding 25 AH, the TEPG-US Models 430548 or 430550 External Battery Charger must be used. (See Control Panel Description under LOCAL PROTECTIVE SIGNALING.)
Siemens Building Technologies Inc, Fire Safety, 8 Fernwood Rd, Florham Park NJ 07932
Automatic Release. ALS2 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL-LG releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 24 AH capacity to provide the required 90 hours of standby operation. Automatic Release. ALS3 Fire Panel (see listing under LOCAL PROTECTIVE SIGNALING). Programmable control. Release circuits are via SIGA-REL-LG releasing module. Used with model RELA-EOL polarized end of line resistor. For deluge and preaction sprinkler system release, compatible solenoid valves include Skinner solenoid valve Model LV2LBX25; ASCO solenoid valves Model T821A107, R821A107, 821A107 and 8210G207; Skinner solenoid valves Model 73218BN4UNLVNOC111C2, 73212BN4TNLVNOC322C2, and 71395SN2ENJ1NOH111C2. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby batteries are available in 65 AH capacity to provide the required 90 hours of standby operation. System 3 Universal Alarm Control. Contains two initiating device circuits for Class A operation. FM Approved configuration consists of CP-35 control panel, PS-35S power supply, BC-35 battery charger and the following modules: DC-35S filter/regulator, TC-30U battery transfer, RM-30U or RM-30RU release, ZN-31U dual contact zone. Compatible solenoid valves are ASCO Models T8210A107, R8210A107, 8210A107 and Skinner Model LV2LBX25. For FM Approved combinations of solenoid and deluge water valves, refer to AUTOMATIC WATER CONTROL VALVES. In the event of primary power failure, two 12 V 55 AH GC12550 batteries provide 90 hours of emergency power. See LOCAL PROTECTIVE SIGNALING listing for other FM Approved modules. MPC-6000 Fire Alarm Control Unit. Modular System made up of various combinations of devices and programmable configurations. Enclosures are MPC6-ENC or MPC6-ENC-B with SFTK-6B or SFTK-6R trim kits. Minimum system configuration includes an MPC6-MB2 main terminal board which includes a regulated 24V power supply, MPC6-DB2 display board with firmware version 7.01, an X1 Addressable Device Circuit with a capacity for 252 Addresses, four independent Class B (Style Y) notification appliance circuits (NACs) which can be combined in pairs for Class A (Style Z) operation, a Serial Interface Circuit that will drive 16 remote LCD annunicators and up to 8 Serial Relay Units and Serial Annuicator Units, four Form C relay contacts each rated at 1A @ 28Vdc and an RJ-11 Programming Port and MPC-REL Releaseing Module with RPT-1 Releasing Power Transformer. 90 hours of secondary power provided by two 12Vdc (38Ah) batteries mounted in an external BE-1 battery box. An optional external BE-1 battery box is available to allow connection of batteries up to 38Ah. For FM Approved combinations of solenoid control valves, refer to Automatic Water Control Valve listings. [See complete MPC-6000 system description under LOCAL PROTECTIVE SIGNALING]. MXL Programmable Modular Fire Alarm System. Uses Version 10.06 operating system and field programming software CSG-M Version 10.03. Requires CSM-4 signal module (configured for releasing service) compatible with Skinner Model LV2LBX25 and ASCO Models 8210A107 (with R or T suffixes) and Alarm-Saf Model AS/PS5-BFS-24-UL power supply. 24 V dc standby batteries rated (15-55 AH) are available for MXL control and Alarm-Saf power supply (31 AH) to provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) MXL-IQ Programmable Modular Fire Alarm System. Uses Version. 6.06 operating system and field programming software CSG-M Version 10.03. Requires CSM-4 signal module (configured for releasing service) compatible with Skinner Model LV2LBX25 and ASCO Models 8210A107 (with R or T suffixes) and Alarm-Saf Model AS/PS5-BFS-24-UL power supply. 24 V dc standby batteries rated (15-55 AH) are available for MXL-IQ control and Alarm-Saf power supply (31 AH) to provide 90 hours of emergency operation. (See also LOCAL PROTECTIVE SIGNALING.) FireFinder XLS Fire Alarm Control System. Modular System made up of various combinations of devices and programmable configurations. Any of the CAB1, CAB2 or CAB3 Cabinet Enclosures may be used with CAB-MP mounting plate, CAB-TK trim kit and card cages CC-2 or CC-5. Any combination system must house a PMI [Person-Machine Interface] considered the main processor with a firmware level at 3.04; a Zone Indicating Card [ZIC-4A] which is equipped with four programmable (Class B) Style Y, or (Class A) Style Z circuits. These output circuits are rated 4A each and must be configured as releasing circuits. A Device Loop Card [DLC] allows a basic system to connect up to 252 addressable analog devices. The DLC has one programmable (Class B) Style 4.0 or (Class A) Style 6 signaling line circuit. Only the (Class A) Style 6 signaling line circuit is permitted for this releasing application. Any combination of the following compatible devices may be connected to the DLC: Manual Pull Stations HMS/S & D, HMS-M, HMS-2S, and HMS-SA; Photoelectric and Thermal sensor HFP-11 with 3.0%/ft nominal obscuration sensitivity and 135F/57C temperature sensor, Thermal sensor HFPT-11 rated at 135F/57C thermal sensitivity suitable for a listed spacing of 20 x 20 feet (6.1 x 6.1 m) with any of the following bases: RL-HC, DB-HR, ADB-11, or ADBX-11; Addressable Switch Interface Module [HTRI-S, -D, -M, or R]; Loop Isolator Module [HLIM]; Two-wire Smoke Interface Module [HZM] which is compatible with Models DI-3/3H, DI-A3/A3H, DI-B3/B3H, DT-3P-135, DT-11, PB-1191, PE-3, and PE-11/11T detectors. The HZM must be converted to (Class A) Style D wiring performance for this releasing application. Each system must be provided with a PSC-12 power supply which provides 120/240 V ac primary and 24 V dc secondary power. The power supply is provided with four Form C relays each rated 4A @120 V ac. Two 12 V dc (15-100 AH) batteries connect to the PSC-12 to provide 90 hours of back up. Optional Power Supply Extender [PSX-12], may be connected to provide additional 24 V dc (12 A) power. For Approved combinations of solenoid and water control valves, refer to the Automatic Water Control Valve listings that follow. [See further description under LOCAL PROTECTIVE SIGNALING]. FS-250 Fire Seeker Fire Alarm Control Unit. Modular System made up of various combinations of devices and programmable configurations. Enclosures are FS-250-ENCL-R or FS-250-ENCL with FS-SFT or FS-SFT-R trim kits. Minimum system configuration includes an FS-250-MB2 main terminal board which includes a regulated 24 V power supply, FS-250-DB2 display board with firmware version 7.01, an
FM Approvals
1-130
FS-DLC device loop card with a P2 Addressable Device Circuit and capacity for 252 Addresses, four independent Class B (Style Y) notification appliance circuits (NACs) which can be combined in pairs for Class A (Style Z) operation, a Serial Interface Circuit that will drive 16 remote LCD annunciators and up to 8 Serial Relay Units and Serial Annunciator Units, four Form C relay contacts each rated at 1A @ 28 V dc and an RJ-11 Programming Port and FS-REL Releasing Module with FS-RPT Releasing Power Transformer. 90 hours of secondary power provided by two 12 V dc (38Ah) batteries mounted in an external CAB-BATT battery box. For Approved combinations of solenoid control valves, refer to Automatic Water Control Valve listings. [See complete FS-250 system description under LOCAL PROTECTIVE SIGNALING].
Siemens Switzerland Ltd, Building Technologies Group, Gubelstrasse 22, CH-6301 Zug Switzerland
ALGORex Fire Detection System. NOTE: This system may not comply with all requirements of NFPA 72-1999 which would be applicable to FM Approval if the equipment were to be marketed in North America. Programmable fire alarm panel (CSCI1145). 24 V dc panel operable on primary voltage rating of 240 V ac. (See CS1140 system description under LOCAL PROTECTIVE SIGNALING.) Preaction and deluge system control requires optional E3G060 I/O module release provides outputs rated at 24 V dc at 2 A max per output, 4 A total per module, alarm horn and illuminated warning panel outputs rated at 24 V dc at 2 A max per output for preaction-deluge releasing and E3M 071 (DS112V3 NLV 1.2) interactive detection line wired Class A Style 7 for alarm initiation. The E3G080 (CS1140/V7.1) provides two release outputs rated at 24 V dc at 2 A max, alarm horn and illuminated warning panel outputs rated at 24 V dc at 2 A max, five monitored detection lines for manual actuation, stop or blocking button (abort), signal contact loss of extinguishing agent, signal contact extinguishing blocked and signal contact extinguishing actuated. Additionally, there is a LON interface (Class B signaling line circuit) for connection to the B3Q440 operating unit extinguishing (Firmware B3Q440/27C256-LON/V1.01). The B3Q440 provides indications and controls for a single extinguishing system. It may be located in the CS1140 enclosure or remotely mounted in a separate enclosure. Indications are provided for alarm, extinguishing command, extinguishing activated, trouble, power on, automatic actuation of extinguishing blocked and manual actuation of extinguishing blocked. Controls provided, in addition to a key switch to inhibit their operation, are: automatic actuation of extinguishing blocked, manual actuation of extinguishing blocked, switch off alarm horn and switch off illuminated warning panel. The B3Q440 also requires a 24 V dc supply from the control unit. (See also LOCAL PROTECTIVE SIGNALING and Automatic Release of Extinguishing Systems)
FM Approvals
1-131
System Sensor, Div of Honeywell, 3825 Ohio Ave, Saint Charles IL 60174
PDRP-1001 with operating system firmware revision level A. Including LED Interface Module (4XLM); Zone Relay Module (4XZM); Remote Annunciator (RZA-4X). Panel provides four input circuits: one detector; one manual release/detector; one waterflow; one supervisory and four output circuits: one alarm/waterflow bell; one waterflow/supervisory bell; one release; one supervisory bell/release. In addition one regulated and one unregulated 24 V auxiliary power output; one alarm and one trouble relay output are provided. Combined load for external devices not to exceed 2.25 A. Field programmable using dip switches for either cross zone or dual zone. For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25 and solenoid for Star Sprinkler Model D deluge valve. For FM Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Transmitter Module (4XTM) provides a local energy municipal tie for auxiliary protective signaling. In the event of primary power failure battery packs (24 V dc, 12, 15 AH) are suitable for 90 hours of standby operation.
Viking Electronic Services LLC, 620 Allendale Rd, King of Prussia PA 19406
e-LAN and e-LAN Lite Fire Alarm Control Panels. Basic system consists of a 4 Amp power supply module (P/N VF8115-00), Control Unit Board (P/N VF1500-00) and Panel Annunciator Board (P/N VF1501-00). Release circuit requires a 2.7K end-of-line device for Squibb supervision (Not required for solenoid operation) and SRM solenoid release module (P/N VF6006-00). For deluge and preaction sprinkler system release, compatible solenoid valves include ASCO Models R8210A107, T8210A107, 8210A107 and Skinner Model LV2LBX25. For Approved combinations of solenoid and water control valves refer to AUTOMATIC WATER CONTROL VALVES. Standby battery (24 V dc, 60 AH) provides 90 hour standby operation. (See control panels descriptions under LOCAL PROTECTIVE SIGNALING).
FM Approvals
1-132
Manufacturer Anber Globe Av de Las Flores 13, Parque Ind El Molino, 28970 Humanes de Madrid, Madrid Spain Grinnell Corp, 3 Tyco Park, Exeter NH 03833
Water Valve Designation & Size *Model A in. NPS Models B, BX. 4, 6 in. NPS; 100, 150 mm NPS 2 1 2
Dry Pilot PneuSprinkler matic Hydraulic Line & Rate-of- Rate-ofActuator Rise# Rise# X [E] X [E]
X [D-1]
X X X X
*Grinnell or Gem Model B. 2 in. NPS Grinnell or Gem Model C. 212, 6 in. NPS Grinnell or Gem Model F445. 212 in. NPS Angle Body Grinnell or Gem Model F446. 212 in. NPS Angle Body. 250 psi (1725 kPa) *Grinnell or Gem Thermal Control Valve Model F430. 1, 112 in. NPS. Wormald Model A1. 100, 150 mm (4, 6 in.) Central Sprinkler Co, 451 N Cannon Ave, Lansdale PA 19446 Model DL. 2 in. Model A. 4, 6 in. NPS Model B, 4 in. Model B, 3, 6 in. NPS Model C, 3, 6, in. NPS Model A-1. 3, 4, 6 in. NPS 250 psi (1725 kPa) Model G-1. 3, 4, 6 in. NPS 250 psi (1725 kPa) Cla-Val Company, Box 1325 Newport Beach CA 92659 Dixon Valve & Coupling Co, 2 Executive Way, Ranson WV 25438 Model 834 4, 6, 8, 10 in. NPS 250 psi (1725 kPa) RWP Automatic Model C. 212, 6 in. NPS Automatic Model 134-260. 2 in. NPS Automatic Models D, F. 212, 4, 6 in. Automatic Model E. 6 in. Flamex Inc, 4365 Federal Drive Greensboro NC 27410 GW Sprinkler A/S, Kastanievej 15, DK-5620 Glamsbjerg, Denmark Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658 Jomos Brandschutz AG, Sagmattstrasse 5, CH-710 Balsthal, Switzerland Magisco Valves Ltd, 53 Limes Rd, Tettenhall, Wolverhampton WV6 8RD United Kingdom Model FSX Deluge Valves 50, 80, 100, 150 mm Model B. 100, 150 mm NPS
X [D-1]
X [D-1]
X [D-1]
X [F]
X [4]
X X X X X X X X X
X [A]
X [A]
X [1] X [2]
X X
X X X X X X [A] [B] [A] [B] X [1] X [2] X [2] X [1] X [2] X [2]
X
[Minimax 20 9353-E]
X[L]
X[11]
X [A]
Model F. 212, 4, 6 in. Model D2, 2 in. NPS Model FSX Deluge Valves. Sizes 50, 80, 100 and 150 mm
X X X
X [B-1, F-1] X
[Minimax 20 9353-E]
MAG Model M799DG-04A, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure. MAG Model M799DG-04B, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure. MAG Model M799DG-04C, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure.
X[D] X [E]
X[1] X[2]
X indicates FM Approved or compatible. #See DELUGE, PREACTION or REFRIGERATED AREA SPRINKLER SYSTEM listings.
DRY PILOT ACTUATOR Compatible models are shown in brackets in the table. Open brackets [ ] indicate none required.
FM Approvals
Any device listed under ELECTRICAL SIGNALING, unless listed for signaling or special application only.
X X X X
1-133
Manufacturer Mil Ltd, 17 Moshe Beker St, Box 15200, Rishon Lezion 75051, Israel
*Model A. 212 in. NPS Models B, BX. 4, 6 in. NPS; 100, 150 mm NPS Model A. 3, 4, 6 in. NPS Model B. 2 in. NPS Model D. 3, 6 in. NPS Model G. 3, 4, 6 in. NPS Model A-1. 3, 4, 6 in. NPS 250 psi (1725 kPa) Model G-1. 3, 4, 6 in. NPS 250 psi (1725 kPa) Model EKFV. DN 200 mm (8 in.). A spool piece containing a 2 in. (51 mm) drain valve is attached to the inlet flange of each valve. Model DV-1. 4, 6 in. NPS
X X X X X X X
X [E] X [D] X [E] X [D] X [A][E] X [A][D][E] X [B] X [C] X [A][E] X [F] X [F]
X [1] X [2] X [1] X [2] X [1] X [2] X [1] X [2] X [2] X [3] X [1] X [2] X [4] X [4]
Total Walther GmbH, Feuerschutz und Sicherheit, Waltherstrasse 51, 51069 Koln, Germany Tyco Fire Products, 451 N Cannon Ave, Lansdale PA 19446
X [DP-1]
Model DV-3. 212 in. NPS. Angle Body. Model DV-3HP. 212 in. NPS. Angle Body. 250 psi (1725 kPa) *Tyco Model DV- 2. 2 in. NPS
X [DP-1]
X X
X [DP-1] X [DP-1]
X [A] X [B] X [D] X [E] X [A] X [D] X [E] X [B] X [F] X X X X [A] [B] [D] [E]
X [1] X [2] X [2] X [1] X [2] X [1] X [2] X [1] X [2] X [1] X [2] X[1] X [2] X [2] X [4] X [1] X [2] X [2] X [1] X [2] X[4]
X X [DP-1] X[F] Model DV-5, 112, 2, 3, 4, 6, 8 in. NPS (40, 50, 80, 100, 150, 200 mm DN) 250 psi (1725 kPa). Tyco Fire Products systems are dual rated and are FM Approved only as a complete Deluge or Preaction System. (See appropriate listing.) System ratings are dependent on the solenoid valve used. Only major electrical components listed above may be interchanged. X X [753A] X [B] X [1] X [2] Series 758 FireLock 112, 2, 212, 3, X X [D] 4, 6 and 8 in. grv grv; 175 psi [776LPA] (1205); X [I] 4, 6 and 8 in. available in flange inlet grv outlet; 300 psi (2070 X X [I] X [I] X [2] kPa). [776LPA] Series 769 FireLock 112, 2, 212, 3, 4, 6 and 8 in. grv x grv; 300 psi (2070 kPa) X X X X X [F] X [4] X [8] *Model E-3, E-4. 112 in. NPT. X [J] X [K] X [1] X [2] *Model E-1, E-2. 2 in. NPT. **Model E-1, E-2. 3, 4, 6 in. NPS. Available with FxF and FxG. Model F-1, F-2: 112, 2, 212, 3, 4, 6, 8 in. NPS. Available with GxG, FxF and FxG and screwed ends (see system description) Above systems: 250 psi (1725 kPa) Viking systems are dual rated and are FM Approved only as a complete Deluge or Preaction System. (See appropriate listing.) Only major electrical components listed above may be interchanged. Solenoid Groups J and K used in Viking Sure-Fire Fail/Safe Systems.
X indicates FM Approved or compatible. #See DELUGE, PREACTION or REFRIGERATED AREA SPRINKLER SYSTEM listings.
DRY PILOT ACTUATOR Compatible models are shown in brackets in the table. Open brackets [ ] indicate none required.
FM Approvals
Any device listed under ELECTRICAL SIGNALING, unless listed for signaling or special application only.
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23849 Bad Oldesloe, Germany Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313 Star Sprinkler Inc, 7071 S 13th, Suite 103, Oak Creek WI 53154
Water Valve Designation & Size INBAL Model 799-DG-01. 3, 4, 6, 8 in. NPS. 6 in. NPS. 300 psi (2070 kPa) rated working pressure. INBAL Model 799-DG-04-A, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure. INBAL Model 799-DG-04-B, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure. INBAL Model 799-DG-04-C, 3, 4, 6, 8 in. NPS. 300 psi (2070 kPa) rated working pressure. Model FSX Deluge Valves. Sizes 50, 80, 100 and 150 mm 232 (16 bar) RWP
PneuElectric Dry Pilot matic Control Wet Pilot Sprinkler Rate- Hydraulic Solenoid Release Panel DetecSprinkler Line & ofRate-of# # tors Groups Groups+ Line Actuator Rise Rise X X
X [L]
X [11]
1-134
Solenoid Group [K]. Viking Model No. 11601 and 11602 (explosion proof) normally closed (NC) solenoid valve, 24 V dc, 9 WATTS, 12 in. NPS, 250 psi (1725 kPa), 6.2 Cv. Viking Model No. 13215 normally open (NO) solenoid valve, 24 V dc, 9 WATTS, 12 in. NPS, 250 psi (1725 kPa), 4.1 Cv. Solenoid Group [L]: Minimax part no. 84 0131 impulse type solenoid valve. The valve shifts position (open or closed) when a voltage pulse is applied to the coil. After shifting position it remains there without electrical power being applied, even if the supply voltage is disconnected. Only when the polarity of the voltage is reversed will the valve shift to the other position. It is the electrical release for the Minimax Model FSX Deluge Valves. In these deulge systems, it is installed in the NC (normally closed) position upon initial set-up. Nominal voltage of 24 Vdc, operating voltage of 18-28 Vdc, 11 WATTS, 460 mA,12 in. NPS, 13 mm (12 in.) orifice dia.
+CONTROL PANELS. Details for panels are listed under AUTOMATIC RELEASES. Panels must have appropriately sized battery to provide required 90 hours of emergency power.
Control Panel Group [1]. These panels are only compatible with Solenoid Groups [A], [D], [E], [G], [I], [J] and [K]:
FM Approvals
1-135
GE Security Inc, 8985 Town Center Pkwy, Bradenton FL 34202 Mirtone, 8985 Town Center Pkwy, Bradenton FL 34202
Model EST2 control panel. Model EST3 control panel. Models MIRQSC, MIRQS1 and MIRQS4 Quick Start Control panels.
ADT Security Services Inc, One Town Center Rd, Boca Raton FL 33486
Unimode-640 Fire Alarm Control Panel.
Buckeye Fire Equipment Co, 110 Kings Road, King Mountain NC 28086
Shield-SZ Fire Alarm Control Panel.
GE Security Inc, 8985 Town Center Pkwy, Bradenton FL 34202 Mirtone, 8985 Town Center Pkwy, Bradenton FL 34202
Model EST2 control panel. Model EST3 control panel. Models QSC, QS1 and QS4 Quick Start Control panels. Model EST2 control panel. Model EST3 control panel. Models MIRQSC, MIRQS1 and MIRQS4 Quick Start Control panels.
FM Approvals
1-136
Pem-All Fire Extinguisher Corp, Div Pem Systems Inc, 39A Myrtle St, Cranford NJ 07016
PEM-2001 Preaction/Deluge Control System.
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
PFC Series 100R, PFC 2000RC. Models PFC-100RC, PFC-4410, PFC-4410A.
Pyrene Corp, 130 Esna Park Dr Markham Ontario L3R 1E3 Canada
Fire Alarm Control Panel Series 4000.
Siemens Building Technologies Inc, Fire Safety, 8 Fernwood Rd, Florham Park NJ 07932
FireFinder XLS Fire Alarm Control System housing a PMI main processor with a firmware level at 3.04. MPC-6000 Fire Alarm Control Unit. MXL Programmable Modular Fire Alarm System. System 3 Universal Alarm Control. FS-250 Fire Seeker Fire Alarm Control Unit
System Sensor, Div of Honeywell, 3825 Ohio Ave Saint Charles IL 60174
PDRP-1001 Preaction/Deluge Control System.
FM Approvals
1-137
Control Panel Group [3]. These panels are compatible with Solenoid Group [C].
ADT Security Services Inc, One Town Center Rd, Boca Raton FL 33486
Unimode-640 Fire Alarm Control Panel.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Micro 1001 Preaction/Deluge Control System.
Pem-All Fire Extinguisher Corp, Div Pem Systems Inc, 39A Myrtle St, Cranford NJ 07016
PEM-2001 Preaction/Deluge Control System.
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
PFC 2000RC.
System Sensor, Div of Honeywell, 3825 Ohio Ave Saint Charles IL 60174
PDRP-1001 Preaction/Deluge Control System.
ADT Security Services Inc, One Town Center Rd, Boca Raton FL 33486
Unimode-640 Fire Alarm Control Panel.
FM Approvals
1-138
Potter Electric Signal Company, 2081 Craig Road, Saint Louis MO 63146
PFC 2000RC.
Siemens Switzerland Ltd, Building Technologies Group, Gubelstrasse 22, CH-6301 Zug Switzerland
CS1140/1145 AlgoRex Fire Detection System. Control Panel Group [6]. These panels are only compatible with Solenoid Groups [A] and [B].
FM Approvals
1-139
Control Panel Group [8]. These panels are compatible with Solenoid Group [F] and [H].
Siemens Building Technologies Inc, Fire Safety, 8 Fernwood Rd, Florham Park NJ 07932
FireFinder XLS Fire Alarm Control System housing a PMI main processor with a firmware level at 3.04. MPC-6000 Fire Alarm Control Unit. FS-250 Fire Seeker Fire Alarm Control Unit Control Panel Group [9]. These panels are compatible with Solenoid Groups [A], [B], [D], [E], [F] and [G]:
Minimax GmbH & Co KG, Box 1260 Industriestrasse 10-12, D-23840 Bad Oldsloe, Germany
Minimax FMZ 4100 GAB 32 Preaction Deluge Control System.
PRESSURE GAUGES
Gauges for sprinkler systems and fire pumps are designed for use with air or water. These gauges are usually of the Bourdon tube type. The moving parts are fabricated of appropriate corrosion-resistant materials. When installed on the air side of a dry pipe system, a retard type gauge may be used. This gauge is assembled with a tube appropriate to the unretarded pressure range of the gauge and is provided with a spring to resist the full scale load. The two common sizes are 412 and 312 in. diameter. These gauges can be calibrated with a hydraulic testing unit by adjusting the dial pointer to read correctly at known pressures. Accuracy requirements are that the gauge be correct within 2% over the center third of its scale and within 3% over the remaining two-thirds. Dial marking subdivisions correspond to the maximum accuracy of the gauge. For service on fire pumps where the suction may be taken under a lift, compound pressure vacuum gauges are available graduated in pressure units over both the pressure and vacuum scales, and are designed not to be injured by vacuum. To minimize possible damage and provide maximum accuracy, gauges should be selected with scales of about twice the maximum system pressure.
Ashcroft Inc, 250 E Main St, Stratford CT 06614
Ashcroft Brand Type 35-W1005P-02L-XUL Pressure Gauge. 0-100 psi (0-690 kPa), 0-150 psi (0-1035 kPa), 0-250 psi (0-1725 kPa), 0-300 psi (0-2070 kPa), 0-600 psi (0-4135 kPa). 312 in. Retard Pressure Gauge. 0-80-250 psi (0-550-1725 kPa).
FM Approvals
1-140
Brecco Corp, 4433 W Van Buren St, Suite #5, Phoenix AZ 85043-3925
Pressure Gauge. Model W-101, Air/Water; 0-300 psi (0-2070 kPa). 312 in. Retard Pressure Gauge. Model W-102, air; 0-80-250 psi (0-550-1725 kPa). 312 in.
Kujawska Fabryka Manometrow KFM S.A., uL. Legska 29/35, 87-800 Wloclawek, Poland
Model 111.10.100. Plastic or steel case with a 14 in. male NPT bottom connection, 4 in. (100 mm) size. Model 111.12.100. Steel case and a 14 in. male NPT rear connection, 4 in. (100 mm) size. Measuring Ranges:
Psi kPa
-1 to 0 -1 to 9 0 to 10 0 to 16 0 to 25 0 to 40
WIKA ALEXANDER WIEGAND GmbH & Co, Alexander-Wiegand-Strae, 63911 Klingenberg, Germany
Pressure Gauge. Model 111.10.100. Plastic or steel case, 312 in size (100 mm). Pressure Gauge. Model 111.12.100. Steel case only, 312 in size (100 mm). Measuring Ranges:
Psi kPa Bar
-1 to 0 -1 to 9 0 to 10 0 to 16 0 to 25 0 to 40
Resilient seat. 4-8 in. sizes only available with AISI 304 stainless steel stem as an alternate material to bronze.
AVK Saudi Valves Manufacturing Co Ltd, Phase 4, Street No. LO 404, Jeddah, KSA 21443
Series 45 Resilient Seated Gate Valves. 212 through 12 in. NPS. Valves have a rated working Pressure of 250 psi (1725 kPa).
212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 DN65, DN80, DN100, DN150, DN200, DN250, and DN300 3, 4, 6, 8 3, 4, 6, 8 4, 6, 8, 10, 12 Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Flanged (ANSI Class 250) Metric, PN 10/16 Grooved End (AWWA C606) Grooved End (AWWA C606) by Flanged Tapping Flange (ANSI Class 125) Standardized Mech. Joint
4-8 in. sizes only available with AISI 304 stainless steel stem as an alternate material to bronze.
FM Approvals
1-141
Series 45 Resilient Seated Gate Valves. 3 through 8 in. NPS valves have a rated working pressure of 250 psi (1725 kPa). 4, 6, and 8 in. NPS sizes only, available with AISI 304 Stainless Steel stems as an alternate material to bronze stems.
3, 4, 6, 8 3, 4, 6, 8 Grooved Ends Flanged by Grooved Ends
American Darling Valve, Div American Cast Iron Pipe Co (ACIPCO), Box 2727, Birmingham AL 35202
All Series 2500-1 . All Series 2500-1 valves have a 250 psi (1725 kPa) working pressure.
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) Standard Mechanical Joint
American Flow Control, Div American Cast Iron Pipe Co (ACIPCO), Box 2727, Birmingham AL 35202
Series 2500. Resilient Seated Gate Valves. 2 through 12 in. NPS valves have a rated working pressure of 250 psi (1725 kPa). 14 and 16 in. NPS valves have a rated working pressure of 200 psi (1380 kPa). Available with the following end connections:
2, 3, 2, 4, 4, 4, 4, 2, 2, 212, 14, 16 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12, 14, 16 6, 8, 10, 12, 14, 16 6, 8, 10, 12 6, 8, 10, 12 6, 8, 10, 12, 14, 16 212, 3, 14, 16 2 1 2, 3 Flanged (ANSI Class 125) Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) Standard Mechanical Joint Push-on Threaded
Series 2500. Resilient Seated Gate Valves. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) x Standardized Mechanical Joint Flanged (ANSI Class 125) x Tyton Tyton Tapping Flange (ANSI Class 125) x Standard Mechanical Joint
Clow Canada, a Div of Canada Pipe, 254 Henry St, Brantford, Ontario N3T 5T7, Canada
Fig. 459. 12 through 2 in. NPS.
Clow Valve Co, Div McWane Inc, 902 S 2nd St, Oskaloosa IA 52577
Series F-6100. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
Model No. Size End Connections
Model 2638. Resilient Seated Gate Valves. Sizes 4 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
4, 4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8, 8 8, 10, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 12 Flanged Flanged Groove Flanged Mechanical Joint Flanged Tyton Grooved Mechanical Joint Mechanical Joint Mechanical Joint Tapping PVC Tyton
10, 12
Model 2639 Resilient Seated Gate Valves. Sizes 212 through 3 in. NPS. 250 psi (1725 kPa) rated working pressure. Sizes 4 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 2 1 2, 3 Flanged Flanged Groove
FM Approvals
1-142
Flanged Mechanical Joint Grooved Mechanical Joint Mechanical Joint Tapping PVC Threaded Tyton
Model 2640. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4 2, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 2, 212, 3, 4, 6, 8, 10, 12 2, 212, 3 4, 6, 8, 10, 12 Flanged Flanged Groove Flanged Mechanical Joint Flanged Tyton Grooved Mechanical Joint Mechanical Joint Mechanical Joint Tapping PVC Threaded Tyton
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien, Taiwan ROC
Model 762U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
2, 3, 4, 6, 8, 10, 12 Flanged
Model 722U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722G. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Grooved
Model 722GF. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Grooved Flanged
Fivalco (Qingdao) Co Ltd, 11 Shuangyuan Road, Chengyang Qingdao, Shandong PRC 266111
Model GVOSY-1161-200PSI. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged Flanged (ANSI, BS10, BS4505, JIS B2212, JIS B2213)
Model GVOSY-1161-250PSI. Resilient Seated Gate Valves. Sizes 4, 6 and 8 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 6, 8 Flanged Flanged (ANSI)
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
Figure 66. Sizes 12 through 2 in. NPS. Available with the following end connections:
12, 34,
1, 114, 112, 2
Threaded
FM Approvals
1-143
Figure 67. Sizes 212 through 6 in. NPS. Available with the following end connections:
212, 3, 4, 6 Threaded
Model Ken-Seal II. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 2 1 2, 3 Flanged Threaded
Model KS-FW. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 2, 212, 3 Flanged Threaded
Model KS-RW. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
4, 6, 8, 10, 12 212, 3, 4, 6, 8 212, 3, 4, 6, 8 Flanged Flanged x Grooved Grooved
Lichfield Fire & Safety Equipment Co Ltd, 2nd Floor, Suite 4, Saturn Centre, Spring Rd, Ettingshall Rd, Wolverhampton WV4 WTX, United Kingdom
Model 762U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
2, 3, 4, 6, 8, 10, 12 Flanged
Model 722U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722G. Resilient Seated Gate Valve. 3, 4 and 6 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6 Grooved
Lien Hwa Iron Works Co Ltd, 112 Sec 2 Kuang Fu Rd, Sanchung Taipei Hsien 24113, Taiwan ROC
Fig. 101F. 212 through 10 in. NPS. Flanged. Fig. 151RB. 212 through 8 in. NPS. Flanged.
Resilient seat.
United Model 5100. Resilient Seated Gate Valves. Sizes 4, 6 and 8 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 6, 8 Flanged Flanged (ANSI)
Milwaukee Valve Company Inc, 16550 West Stratton Drive, New Berlin WI 53151
Model 2885FP. Metal to Metal Seated Gate Valve. 212 through 8 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8 Flanged
FM Approvals
1-144
Figure 118. Metal to Metal Seated Gate Valve. 1 through 2 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
1, 114, 112, 2 Threaded
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Quikcoup Style 400. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged Flanged (ANSI, BS10, BS4505, JIS B2212, JIS B2213)
Quikcoup Style 425. Resilient Seated Gate Valves. Sizes 4, 6 and 8 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 6, 8 Flanged Flanged (ANSI)
3, 4, 6, 8, 10, 12, 14 2, 212, 3, 4, 6, 8, 10, 12, 14 2, 212, 3, 4, 6, 8 3, 4, 6, 8, 10, 12, 14 3, 4, 6, 8, 10, 12, 14 4, 6, 8, 10, 12, 14 3, 4, 6, 8, 10, 12, 14
Hub Flanged Threaded Flanged by Mechanical Joint Standardized Mechanical Joint Asbestos Cement Hub Flanged by Asbestos Cement Hub
Series 2079. Resilient Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Available with the following end connections.
Figure No. Size End Connections
4, 4, 4, 4, 4,
6, 8, 6, 8, 6, 8, 6, 8, 6, 8, 4, 6
10 10 10 10 10
Flanged Flanged by Mechanical Joint Mechanical Joint A/C Pipe Ends Flanged by A/C Pipe End Flanged by Grooved
Figure 2360*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8 4, 6, 8, 10, 12 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Mechanical Joint by Standardized Mechanical Joint (Cut In/D150) Slip On Slip On by Flange Threaded
Figure 2361*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8, 8 10, 10, 10, 10, 10, 10, 10, 12, 12, 12, 12 12, 12, 12 14**, 16** 14**, 16** 14**, 16** 14**, 16** 14**, 16** Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange AquaGrip restrained mechanical joint, NPS AquaGrip restrained mechanical joint, IPS
Figure 2362*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, Flanged Threaded Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange
Figure 2460. Resilient Seated Gate Valves. 250 psi (1724 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D-150) Slip On Threaded
FM Approvals
1-145
Figure 2462. Resilient Seated Gate Valves. 250 psi (1724 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D-150) Slip On Threaded
*Bonnet with indicator post flange. **Rated Working Pressure 250 psi (1724 kPa).
AquaGrip end connections FM Approved for use with FM Approved PVC, HDPE and ductile iron pipe. 10 and 12 in. NPS AquaGrip end connections limited to 160 psi (1105 kPa) rated working pressure when used with HDPE pipe.
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Model NF-OSY175U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 Flanged
Model NF-OSY200U. Resilient Seated Gate Valve. 2 12 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model NF-OSY250H. Resilient Seated Gate Valve. 2 12 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model NF-OSY250G. Resilient Seated Gate Valve. 3 through 8 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2 12, 3, 4, 6, 8, 10, 12 Grooved
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
Model 762U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
2, 3, 4, 6, 8, 10, 12 Flanged
Model 722U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722G. Resilient Seated Gate Valve. 3, 4 and 6 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6 Grooved
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model RELOSY-200-RW. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged Flanged (ANSI, BS10, BS4505, JIS B2212, JIS B2213)
Model RELOSY-250-RW. Resilient Seated Gate Valves. Sizes 4, 6 and 8 in. NPS 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 6, 8 Flanged Flanged (ANSI)
Shanghai Karon Valves Machinery Co Ltd, No 815 Deyuan Road Nanxiang, Jiading District Shanghai, PRC
Series RRHX. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 232 psi (1600 kPa) rated working pressure. Available with the following end connections:
FM Approvals
1-146
Model No
Size
End Connections
RRHX XXX
XXX Valve size in millimeters.
2, 212, 3, 4, 5, 6, 8, 10, 12
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Model 762U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 Flanged
Model 722U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Model 722H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Model 722G. 3, 4 and 6 in. NPS. Grooved ends. Resilient Seated. 200 psi (1380 kPa).
Siam Cast Iron Works Co Ltd, Samutsakorn Industrial Estate, Soi 7, 1/12 Moo 2, Rama II Rd, Tahsai, Muang, Samutsakorn 74000, Thailand
Model 105U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Grooved
Stockham Valves & Fittings, 2129 3rd Ave SE, Cullman AL 35055-5477
No. G-610. 212 through 12 in. Flanged, 200 psi (1380 kPa). No. B-133. 1 through 2 in. NPS. No. G-633. 212 through 6 in. NPS. Screwed. No. G-634. 212 through 14 in. NPS. Flanged. No. F-670. 2 through 10 in. NPS, flanged, 300 psi (2070 kPa) working pressure; 12 in. NPS, flanged, 250 psi (1725 kPa) working pressure.
Tong Kwang Valve Industrial Co Ltd, No. 1-1 Ming Chuan Rd, Ming-Sheng Li Tansui, Taipei Hsien, Taiwan ROC
Model 073U. 2, 212, 3, 4, 6, 8, 10 and 12 in. NPS. Flanged.
Tyco Water Valve (Shanghai) Co Ltd, No. 399 Jiu Ye Road, Qing Pu Industrial Zone, Shanghai China 201700
Series TM Resilient Seated Gate Valves. Rated working pressure 232 psi (1600 kPa). Available with the following end connections:
Model No. Size End Connections
3, 4, 5, 6, 8, 10, 12 2, 50, 65, 80, 100, 125, 150, 200, 250, 300 2, 3, 4, 5, 6, 8, 10, 12 50, 65, 80, 100, 125, 150, 200, 250, 300 2, 3, 4, 5, 6, 8, 10, 12, 50, 65, 80, 100, 125, 150, 200, 250, 300 2 1 2, 212,
212,
United States Pipe & Foundry Co, 3300 First Ave N, Birmingham AL 35222
Metroseal Series*. 4, 6, 8, 10, 12, 14 and 16 in. NPS. 250 psi (1725 kPa) working pressure. Double flanged, double mechanical joint ends and flanged by mechanical joint ends through 16 in. nominal size, Tyton ends through 12 in. nominal size and TR Flex ends in 16 in. nominal size only.
*Resilient seat.
Figure USP0*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 212, Compression Ends Flanged Standardized Mechanical Joint
FM Approvals
1-147
4, 6, 8, 3, 4, 6, 4, 6, 8 4, 6, 8 4, 6, 8, 4, 6, 8, 212, 3
10, 12 8, 10, 12
10, 12 10, 12
Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Mechanical Joint by Standardized Mechanical Joint (Cut In/D150) Slip On Slip On by Flange Threaded
Figure USP1*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8, 8 10, 10, 10, 10, 10, 10, 10, 12, 12, 12, 12 12, 12, 12 14**, 16** 14**, 16** 14**, 16** 14**, 16** 14**, 16** Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange AquaGrip restrained mechanical joint, NPS AquaGrip restrained mechanical joint, IPS
Figure USP2*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
212, 3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 Flanged Threaded Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange
*Bonnet with indicator post flange. **Rated Working Pressure 250 psi (1724 kPa).
AquaGrip end connections FM Approved for use with FM Approved PVC, HDPE and ductile iron pipe. 10 and 12 in. NPS AquaGrip end connections limited to 160 psi (1105 kPa) rated working pressure when used with HDPE pipe.
Figure 771H. Resilient Seated Gate Valve. Sizes 212 through 12 in. NPS and 165.1 mm DN, 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12, (165.1 mm) Grooved
Figure 771F. Resilient Seated Gate Valve. Sizes 212 through 12 in. NPS and 165.1 mm DN, 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12, (165.1 mm) Grooved Flanged
Flanged Flanged (ANSI Class 125, BS10 Table E, BS4505 DIN PN10, JIS B2212, JIS B2213)
FIREKING Fig. No. OF250-####. Resilient Seated Gate Valves. Sizes 4 through 8 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
4, 6, 8
#### Valve size in millimeters
Flanged Flanged (ANSI Class 125, BS10 Table E, BS4505 DIN PN10 & PN16, JIS B2212, JIS B2213)
Waterous Co, 125 Hardman Ave So, South Saint Paul MN 55075-1191
All Series 2500-1 . All Series 2500-1 valves have a 250 psi (1725 kPa) working pressure. Available in the following end connections:
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) Standard Mechanical Joint
Series 2500. Resilient Seated Gate Valves. 2 through 3 in. NPS OS&Y valves have a rated working pressure of 250 psi (1725 kPa). Available with the following end connections:
2, 212 3 2, 3 Flanged (ANSI Class 125) Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint
FM Approvals
1-148
2, 212, 3 2, 212, 3
Model 409. Resilient Seated Gate Valves. Sizes 2 through 10 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10 212, 3, 4, 6, 8, 10 212, 3, 4, 6, 8, 10 2 Flanged Flanged Flanged Grooved Grooved Grooved Thread Thread
AVK Saudi Valves Manufacturing Co Ltd, Phase 4, Street No. LO 404, Jeddah, KSA 21443
Series 45. Resilient seat gate valves, with or without Indicator Post Flange. 250 psi (1725 kPa) working pressure.
3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 DN65, DN80, DN100, DN150, DN200, DN250, and DN300 3, 4, 6, 8 3, 4, 6, 8 4, 6, 8, 10, 12 212, Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Flanged (ANSI Class 250) Metric, PN 10/16 Grooved End (AWWA C606) Grooved End (AWWA C606) by Flanged Tapping Flange (ANSI Class 125) Standardized Mech. Joint
Series 45 Resilient Seated Gate Valves. 3 through 8 in. NPS valves have a rated working Pressure of 250 psi (1725 kPa). 4, 6 and 8 in. NPS sizes only, available with AISI 304 Stainless Steel stems as an alternate material to bronze stems. 4 through 8 in. available with or without
3, 4, 6, 8 3, 4, 6, 8 Grooved Ends Flanged by Grooved Ends
American Darling Valve, Div American Cast Iron Pipe Co (ACIPCO), Box 2727 Birmingham AL 35202
Series 2500-1. All Series 2500-1 valves have a 250 psi (1725 kPa) working pressure and 4 through 12 in. sizes are available with or without an indicator post flange.
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) x Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) x Standard Mechanical Joint
FM Approvals
1-149
American Flow Control, Div American Cast Iron Pipe Co (ACIPCO), Box 2727, Birmingham AL 35202
Series 2500. Resilient Seated Gate Valves. 2 through 12 in. NPS valves have a rated working pressure of 250 psi (1725 kPa). 14 and 16 in. NPS valves have a rated working pressure of 200 psi (1380 kPa). Available with the following end connections:
2, 3, 2, 4, 4, 4, 4, 2, 2, 212, 14, 16 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12, 14, 16 6, 8, 10, 12, 14, 16 6, 8, 10, 12 6, 8, 10, 12 6, 8, 10, 12, 14, 16 212, 3, 14, 16 2 1 2, 3 Flanged (ANSI Class 125) Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) Standard Mechanical Joint Push-on Threaded
Clow Valve Co, Div McWane Inc, 902 S 2nd St, Oskaloosa IA 52577
Series F-5700. Metal to Metal Seated Gate Valves. Sizes 212 through 14 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
Model No. Size End Connections
F-5702 F-5705 F-5707 F-5710 F-5712 F-5715 Tapping F-5717 Tapping F-5720* F-5722* F-5725* F-5727* F-5730* F-5731 F-5732
3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12, 14 12, 3, 4, 6, 8, 10, 12, 14 2 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 212, 3 2 1 2, 3
Hub Flanged Mechanical Joint Ring-Tite Flanged Mechanical Joint Mechanical Joint Hub Hub Flanged Mechanical Joint Ring-Tite Flanged Mechanical Joint Push-on for PVC Threaded
Series F-6100. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
Model No. Size End Connections
2, 212, 3, 4, 6, 8, 10, 12 2, 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 2, 212, 3, 4, 6, 8 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 2, 212, 3, 4, 6, 8
Flanged Mechanical Joint Flanged Mechanical Joint Push-on for PVC Flanged Mechanical Joint Flanged Mechanical Joint Push-on for PVC
Model 2638. Resilient Seated Gate Valves. 4 through 16 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
4, 4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8 8, 8, 10, 10, 10, 10, 10, 10, 12, 12, 12, 12, 12 12, 14, 16 14, 16 16 14, 16 14, 16 Mechanical Joint Flanged Tyton Mechanical Joint Flanged Tyton Flanged Mechanical Joint Tapping Flange PVC Groove Groove Flange
10, 12 10, 12
Model 2639 Resilient Seated Gate Valves. Sizes 2 through 3 in. NPS. 250 psi (1725 kPa) rated working pressure. Sizes 4 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4 2, 3, 4, 6, 8, 10, 12 Flanged Flanged Groove Flanged Mechanical Joint Flanged Tyton Grooved Mechanical Joint
FM Approvals
1-150
3, 2, 2, 4,
Model 2640. Resilient Seated Gate Valves. 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2, 212, 3, 4, 6, 8, 10, 12 2 1 2 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4 2, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 2, 212, 3, 4, 6, 8, 10, 12 2, 212, 3 4, 6, 8, 10, 12 Flanged Flanged Groove Flanged Mechanical Joint Flanged Tyton Grooved Mechanical Joint Mechanical Joint Mechanical Joint Tapping PVC Threaded Tyton
East Jordan Iron Works Inc, 301 Spring Street, East Jordan MI 49727
4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 12 12 12 12 12 Mechanical Joint Mechanical Joint Mechanical Joint Tapping Flange Mechanical Joint Flat Flange Tyton Tyton Flange Flange
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien, Taiwan ROC
Model 710U. Metal to Metal Seated Gate Valve. 212 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721G. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Grooved
Model 721GF. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Grooved Flanged
Fivalco (Qingdao) Co Ltd, 11 Shuangyuan Road Chengyang, Qingdao Shandong, PRC 266111
Model GVNRS-1161-200PSI. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged Flanged ANSI, BS10, BS4505, JIS B2212, JIS B2213)
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
KS-FW. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
2, 2, 3, 4, 2, 2, 4, 4, 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 6, 8, 10, 12 212, 3, 4, 6, 8 2 1 2, 3 6, 8, 10, 12 6, 8, 10, 12 Flanged Mechanical Joint Mechanical Joint Flanged Mechanical Joint Tapping Flanged Push-On for PVC Threaded Tyton Tyton Flanged
KS-RW. Resilient Seated Gate Valves. Sizes 4 through 12 in. NPS 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
4, 4, 4, 4, 6, 6, 6, 6, 8, 8, 8, 8, 10, 10, 10, 10, 12 12 12 12 Flanged Mechanical Joint Mechanical Joint x Flanged Mechanical Joint x Tapping Flange
FM Approvals
1-151
4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8
Ken-Seal D. Resilient Seated Gate Valves. 4 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
4, 4, 4, 4, 6, 4, 4, 6, 6, 6, 6, 8, 6, 6, 8, 10, 12 8, 10, 12 8, 10, 12 8, 10, 12 10, 12 8, 10, 12 8 Standardized Mechanical Joint Flanged Push On Standardized Mechanical Joint by Flanged Push On by Flanged Standardized Mechanical Joint by Tapping Flange Push On for PVC pipe
Ken-Seal II. Resilient Seated Gate Valves. 2 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
2, 3, 4, 2, 4, 4, 4, 2, 2, 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 6, 8, 10, 12 3, 4, 6, 8, 10, 12 6, 8, 10, 12 6, 8, 10, 12 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 2 1 2, 3 Flanged Flanged by Standardized Mechanical Joint Flanged by Push-On Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Push-On Push-On for PVC Threaded
Model 2620. 14 in. NPS. Available with standardized mechanical joint and flanged ends.
Bonnet without indicator post flange.
Lichfield Fire & Safety Equipment Co Ltd, 2nd Floor, Suite 4, Saturn Centre, Spring Rd, Ettingshall Rd, Wolverhampton WV4 WTX, United Kingdom
Model 710U. Metal to Metal Seated Gate Valve. 212 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721G. Resilient Seated Gate Valve. 3, 4 and 6 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6 Grooved
Lien Hwa Iron Works Co Ltd, 112 Sec 2 Kuang Fu Rd, Sanchung Taipei Hsien 24113, Taiwan ROC
Fig. 253RB. 4 through 8 in. NPS. Flanged. Fig. 263RB. 4 through 8 in. NPS. Standardized mechanical joint.
Resilient seat.
FM Approvals
1-152
Series 7000. Resilient Seated Gate Valves. Sizes 4 through 12 in. NPS. 200 psi (1380 kPa) rated working Pressure. All available with or without indicator post flange. Available with the following end connections:
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged Mechanical Joint Mechanical Joint Flange Mechanical Joint Tapping Push-on Joint Push-on Flange
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Quikcoup Style 450. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged Flanged (ANSI, BS10, BS4504, JIS B2212, JIS B2213)
4, 4, 4, 4, 4,
6, 6, 6, 6, 6,
8, 8, 8, 8, 8,
14 14 14 14 14
Hub Flanged Mechanical Joint Asbestos Cement Hub Flanged by Asbestos Cement Hub
Series 2052*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Available with the following end connections.
Figure No. Size End Connections
4, 4, 4, 4, 4, 4, 4,
6, 6, 6, 6, 6, 6, 6,
8, 8, 8, 8, 8, 8, 8,
14 14 14 14 14 14 14
Hub Flanged Flanged by Asbestos Cement Hub Mechanical Joint Mechanical Joint Asbestos Cement Hub Flanged by Asbestos Cement Hub
Series 2074. Resilient Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Available with the following end connections.
Figure No. Size End Connections
4, 4, 4, 4, 4,
6, 6, 6, 6, 6,
8, 8, 8, 8, 8, 4,
12 12 12 12 12
Flanged Flanged by Mechanical Joint Mechanical Joint Asbestos Cement Hub Flanged by Asbestos Cement Hub Flanged by Grooved
Series 2075*. Resilient Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Available with the following end connections.
Figure No. Size End Connections
4, 4, 4, 4, 4, 4,
6, 6, 6, 6, 6, 6,
8, 8, 8, 8, 8, 8,
12 12 12 12 12 12
Flanged Flanged by Mechanical Joint Mechanical Joint Asbestos Cement Hub Flanged by Asbestos Cement Hub Slip-On Ends
Series 645*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Tapping Valve. Available with the following end connections.
Figure No. Size End Connections
A-645
4, 6, 8, 10, 12
Series 698*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Tapping Valve. Available with the following end connections.
Figure No. Size End Connections
A-698
4, 6, 8, 10, 12, 14
Flanged by Hub
Series 699*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Tapping Valve. Available with the following end connections.
Figure No. Size End Connections
A-699
4, 6, 8, 10, 12, 14
Series 876*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Cut-in valve with duck-tipped rubber gaskets. Available with the following end connections.
FM Approvals
1-153
Figure No.
Size
End Connections
A-876
4, 6, 8, 10, 12
Mechanical Joint
Series 877*. Metal Seated Gate Valves. 175 psi (1205 kPa) rated working pressure. Cut-in valve with plain rubber gaskets. Available with the following end connections.
Figure No. Size End Connections
A-877
4, 6, 8, 10, 12
Mechanical Joint
Figure 2360*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8 4, 6, 8, 10, 12 4, 6, 8, 10, 12 2 1 2, 3 212, Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Mechanical Joint by Standardized Mechanical Joint (Cut In/D150) Slip On Slip On by Flange Screwed
Figure 2361*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8, 8 10, 10, 10, 10, 10, 10, 10, 12, 12, 12, 12 12, 12, 12 14**, 16** 14**, 16** 14**, 16** 14**, 16** 14**, 16** Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange AquaGrip restrained mechanical joint, NPS AquaGrip restrained mechanical joint, IPS
Figure 2362*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
212, 3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 Flanged Threaded Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange
Figure 2460. Resilient Seated Gate Valves. 250 psi (1724 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Slip On Threaded
Figure 2461. Resilient Seated Gate Valves. 250 psi (1724 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
4, 4, 3, 4, 6, 6, 4, 6, 8, 8, 6, 8, 10, 12 10, 12 8, 10, 12 10, 12 Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Tapping Flange Slip On
Figure 2462. Resilient Seated Gate Valves. 250 psi (1724 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Slip On Threaded
*Bonnet with indicator post flange. **Rated Working Pressure 250 psi (1724 kPa).
AquaGrip end connections FM Approved for use with FM Approved PVC, HDPE and ductile iron pipe. 10 and 12 in. NPS AquaGrip end connections limited to 160 psi (1105 kPa) rated working pressure when used with HDPE pipe.
FM Approvals
1-154
Flanged (ANSI/ISO 2084) Standardized Mechanical Joint Standardized Mechanical Joint by Flange
Figure F609RW. Resilient Seated Gate Valves. 250 psi (1725 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 Flanged (ANSI) Standardized Mechanical Joint Standardized Mechanical Joint by Flange
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Model NF-NRS175U. Metal to Metal Seated Gate Valve. 212 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model NF-NRS200U. Resilient Seated Gate Valve. 2 12 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model NF-NRS250H. Resilient Seated Gate Valve. 2 12 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model NF-NRS250G. Resilient Seated Gate Valve. 3 through 8 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6, 8, Grooved
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
Model 710U. Metal to Metal Seated Gate Valve. 212 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721G. Resilient Seated Gate Valve. 3, 4 and 6 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6 Grooved
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model RELNRS-200-RW. Resilient Seated Gate Valves. Sizes 212 through 12 in. NPS 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 Flanged 1 Flanged (ANSI, BS10, BS4505, JIS B2212, JIS B2213)
*Sizes 4 in. NPS and larger are available with indicator post flange.
Shanghai Karon Valves Machinery Co Ltd, No. 815 Deyuan Road Nanxiang, Jiading District Shanghai, PRC
Series RVCX. Resilient Seated Gate Valves. Sizes 2 through 12 in. NPS. 232 psi (1600 kPa) rated working pressure. Available with the following end connections:
FM Approvals
1-155
Model No.
Size
End Connections
RVHX/RVCX XXX
XXX Valve size in millimeters.
2, 212, 3, 4, 5, 6, 8, 10, 12
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Model 710U. Metal to Metal Seated Gate Valve. 212 through 12 in. NPS. 175 psi (1205 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721U. Resilient Seated Gate Valve. 212 through 12 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Model 721H. Resilient Seated Gate Valve. 212 through 12 in. NPS. 250 psi (1725 kPa) rated working pressure. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 Flanged Mechanical Joint
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Model 721G. Resilient Seated Gate Valve. 3 through 6 in. NPS. 200 psi (1380 kPa) rated working pressure. Available with the following end connections:
3, 4, 6 Grooved
Stockham Valves & Fittings, 2129 3rd Ave SE, Cullman AL 35055-5477
G-600. 4 through 12 in. Flanged with indicator post flange. 200 psi (1380 kPa). G-601. 4 through 12 in. Standardized mechanical joint, with indicator post flange. 200 psi (1380 kPa). G-602. 4 through 12 in. NPS. Flanged by mechanical joint end, with indicator post flange. 200 psi (1380 kPa). G-603. 4 through 12 in. Tyton joint, with indicator post flange. 200 psi (1380 kPa). G-604. 4 through 12 in. Flanged by Tyton pipe end, with indicator post flange. 200 psi (1380 kPa). G-605. 4 through 12 in. Flanged. 200 psi (1380 kPa). G-606. 4 through 12 in. Standardized mechanical joint, flanged. 200 psi (1380 kPa). G-607. 4 through 12 in. Tyton ends. 200 psi (1380 kPa). G-616. 4 through 12 in. Flanged by mechanical joint end. 200 psi (1380 kPa). G-617. 4 through 12 in. Flanged by Tyton end. 200 psi (1380 kPa). No. G-632. 4 through 12 in. NPS. Flanged. No. G-635. 4 through 14 in. NPS. Standardized mechanical joint. No. G-638. 4 through 14 in. NPS. Ring-Tite.
Tyco Water Valve (Shanghai) Co Ltd, No. 399 Jiu Ye Road, Qing Pu Industrial Zone, Shanghai China 201700
Series TM Resilient Seated Gate Valves. Rated working pressure 232 psi (1600 kPa) Available with the following end connections:
Model No. Size End Connections
TMCX-XXXX
2, 212, 3, 4, 5, 6, 8, 10, 12 50, 65, 80, 100, 125, 150, 200, 250 and 300 2, 212, 3, 4, 5, 6, 8, 10, 12 50, 65, 80, 100, 125, 150, 200, 250 and 300 2, 212, 3, 4, 5, 6, 8, 10, 12 50, 65, 80, 100, 125, 150, 200, 250 and 300
TMCG-XXXX
Grooved Grooved
TMCT-XXXX
Flanged Grooved
Series TM, Indicator Post Flange. Rated working pressure 232 psi (1600 kPa). Available with the end connections listed below:
Model No. Size End Connections
TMCX-P-XXXX *
4, 5, 6, 8, 10, 12 100, 125, 150, 200, 250 and 300 4, 5, 6, 8, 10, 12 100, 125, 150, 200, 250 and 300 4, 5, 6, 8, 10, 12 100, 125, 150, 200, 250 and 300
TMCG-P-XXXX *
Grooved x Grooved
TMCG-P-XXXX *
Flanged x Grooved
XXXX = Valve size in millimeters. * Bonnet with indicator post flange. Bonnet without indicator post flange.
FM Approvals
1-156
United States Pipe & Foundry Co, 3300 First Ave N, Birmingham AL 35222
Metroseal Series*. 4, 6, 8, 10, 12, 14 and 16 in. NPS. 250 psi (1725 kPa) working pressure. Double flanged, double mechanical joint ends and flanged by mechanical joint ends through 16 in. nominal size, Tyton ends through 12 in. nominal size and TR Flex ends in 16 in. nominal size only. With and without indicator post flange.
*Resilient seat.
Figure USP0*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
212, 3, 4, 6, 8 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8 4, 6, 8 4, 6, 8, 10, 12 4, 6, 8, 10, 12 2 1 2, 3 Compression Ends Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Mechanical Joint (Cut In/D150) Mechanical Joint by Standardized Mechanical Joint (Cut In/D150) Slip On Slip On by Flange Screwed
Figure USP1*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
4, 4, 4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 8, 8 10, 10, 10, 10, 10, 10, 10, 12, 12, 12, 12 12, 12, 12 14**, 16** 14**, 16** 14**, 16** 14**, 16** 14**, 16** Flanged Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange AquaGrip restrained mechanical joint, NPS AquaGrip restrained mechanical joint, IPS
Figure USP2*. Resilient Seated Gate Valves. 200 psi (1380 kPa) rated working pressure. Available with the following end connections.
212, 3, 4, 6, 8, 10, 12 2 1 2, 3 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 212, 3, 4, 6, 8, 10, 12 4, 6, 8, 10, 12 Flanged Threaded Standardized Mechanical Joint Standardized Mechanical Joint by Flanged Standardized Mechanical Joint by Tapping Flange Slip On Slip On by Flange
*Bonnet with indicator post flange. **Rated Working Pressure 250 psi (1724 kPa).
AquaGrip end connections FM Approved for use with FM Approved PVC, HDPE and ductile iron pipe. 10 and 12 in. NPS AquaGrip end connections limited to 160 psi (1105 kPa) rated working pressure when used with HDPE pipe.
Figure 772H. Resilient Seated Gate Valve. Sizes 212 through 12 in. NPS and 165.1 mm DN, 250 psi (1725 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12, (165.1 mm) Grooved
Figure 772F. Resilient Seated Gate Valve. Sizes 212 through 12 in. NPS and 165.1 mm DN, 250 psi (1725 kPa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the following end connections:
212, 3, 4, 6, 8, 10, 12, (165.1 mm) Grooved Flanged
Waterous Co, 125 Hardman Ave So, South Saint Paul MN 55075-1191
Series 2500-1 . All Series 2500-1 valves have a 250 psi (1725 kPa) working pressure and 4 through 12 in. sizes are available with or without an indicator post flange. Available in the following end connections:
4, 4, 4, 4, 4, 4, 6, 6, 6, 6, 6, 6, 8, 8, 8, 8, 8, 8, 10, 10, 10, 10, 10, 10, 12 12 12 12 12 12 Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Flanged (ANSI Class 125) Standardized Mechanical Joint Flanged (ANSI Class 125) Tyton Tyton Tapping Flange (ANSI Class 125) Standard Mechanical Joint
FM Approvals
1-157
Series 2500. Resilient Seated Gate Valves. 2 through 3 in. NPS NRS valves have a rated working pressure of 250 psi (1725 kPa). 14 and 16 in. NPS valves have a rated working pressure of 200 psi (1380 kPa). Available with the following end connections:
2, 212, 14, 16 3 2, 3, 14, 16 2, 212, 3 2, 212, 3 14, 16 14, 16 14, 16 Flanged (ANSI Class 125) Flanged (ANSI Class 125, 150, 250) Standardized Mechanical Joint Push-on for PVC Pipe NPT Threaded Flanged (ANSI Class 125) Standardized Mechanical Joint Tapping Flange (ANSI Class 125) x Standard Mechanical Joint Push-on for D. I. Pipe
AE7722-3A
Remarks:
300 (2070)
a, b, c
a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor service. c. FM Approved for aboveground installations only.
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Model Number Product Type Nominal Pipe Size in. / mm Rated Working Pressure, psi (kPa) Remarks
AE7722-3A
Remarks:
300 (2070)
a, b, c
a. Available with dual supervisory switches. b. Approved for indoor and outdoor service. c. Approved for aboveground installations only.
DANFOSS SOCLA S.A.S., 365, rue du Lieutenant Putier, 71530 Virey-Le-Grand, France
Model Number Product Type Nominal Pipe Size, mm Rated Working Pressure, psi (kPa) Remarks
BOMBYX
32, 40, 50, 65, 80, 100, 125, 150, 200, 250, 300
232 (1600)
a, b, c
Remarks: a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor service. c. FM Approved for aboveground installations only.
Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body Butterfly Valve, Grooved Ends
212, 3, 4, 6, 8
175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070)
a, b a, b a, b a, b a, b
FM Approvals
1-158
Model Number
Product Type
Remarks
Fireriser-HPW
Remarks:
212, 3, 4, 6, 8
300 (2070)
a, b
a. Available with dual supervisory switches. b. Approved for above ground, indoor and outdoor use only.
Global Safety Products Inc, 970 E Orangethorpe Ave, Unit B, Anaheim CA 92801
Model Number Product Type Nominal Pipe Size, in. (mm) Rated Working Pressure, psi (kPa) Remarks
BV-W
Butterfly Valve, Wafer Body Butterfly Valve, Grooved Ends Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body
212, 3, 4, 5, 6, 8 (65), (80), (100), (125), (150), (200) 212, 3, 4, 5, 6, 8 (65), (125), (150) 1, 114, 112, 1, 2, 212
175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070)
a, c, d
BV-G
a, c, d
BB-T
a, c, d
BB-G
2, 212
a, c, d
BO-G 300
212, 3, 4, 5, 6, 8 (65), (125), (150), (200) 212, 3, 4, 5, 6, 8 (65), (80), (100), (125), (150), (200)
a, b, c
BO-W 300
Remarks: a. b. c. d.
a, b, c
Available with dual supervisory switches. FM Approved for indoor and outdoor service. FM Approved for aboveground installations only. FM Approved for indoor service only.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Model Number Product Type Nominal Pipe Size Rated Working Pressure, psi (kPa) Remarks
Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body
212, 3, 4, 6, 8 212, 3, 4, 6, 8
175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070)
a, b a, b a, b a, b a, b a, b
a. Available with dual supervisory switches. b. Approved for above ground, indoor and outdoor use only.
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
Model Number Product Type Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
Figure 82M
Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends
3, 4, 5, 6, 8
c, d
Figure 83M
3, 4, 5, 6, 8
c, d
Figure 93G
212, 3, 4, 6, 8
a, c, d
FM Approvals
1-159
Model Number
Product Type
Remarks
Figure 93W
212, 3, 4, 6, 8
175 (1205)
a, c, d
Figure 01G
Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends, Extended Length Butterfly Valve, Wafer Style (ANSI) Butterfly Valve, Grooved Ends Butterfly Valve, Grooved Ends, Extended Length
212, 3, 4, 6, 8
a, c, d
Figure 02G
a, c, d
Figure 01W
212, 3, 4, 6, 8
a, c, d
Figure G300
212, 3, 4, 6
a, b, c
Figure G300E
212, 3, 4, 6
a, b, c
Remarks: a. b. c. d. Available with dual supervisory switches. FM Approved for indoor and outdoor service. FM Approved for aboveground installations only. FM Approved for indoor service only.
Milwaukee Valve Company Inc, 16550 West Stratton Drive, New Berlin WI 53151
Model Number Product Type Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
BBSC
Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends
b, c, d
BBSC
b, c, d
BBSCS
a, b, c, d
BBSCS
Remarks: a. b. c. d.
a, b, c
Available with dual supervisory switches. FM Approved for indoor and outdoor service. FM Approved for aboveground installations only. FM Approved when supplied with female NPT threaded end connections.
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Model 200 Wafer body (for mounting between bolted flanges). 212, 3, 4, 6, 8 in. NPS and 65, 80, 100, 150 and 200 mm NPS. Model 100. Grooved inlet and outlet connections. 212, 3, 4, 6, 8 in. NPS and 65 and 150 mm NPS. Model 500-T. Threaded connections. 1, 114, 112, 2, 212 in. NPS. Model 500-G. Grooved inlet and outlet connections. 2, 212 in. NPS. Valves are FM Approved for aboveground indoor use only. Valves are available with two supervisory switches.
B3250-00
Butterfly Valve, Wafer Body Butterfly Valve, Wafer or Lug Body Butterfly Valve, Wafer or Lug Body Butterfly Valve, Grooved End Butterfly Valve, Grooved End
2, 212, 3, 4, 5, 6, 8
175 (1205) 250 (1725) 250 (1725) 300 (2070) 300 (2070)
c, d
B3253-00
2, 212, 3, 4, 5, 6
a, b, c
B3253-00
8, 10, 12
a, c, d
B3254-52
3, 4, 6, 165 mm
a, b, c
B3254-52
Remarks:
a, c, d
FM Approvals
1-160
a. b. c. d.
Available with supervisory switches. FM Approved for indoor and outdoor service. FM Approved for aboveground installations only. FM Approved for indoor service only.
WD-3510-4 WD-3510-8 LD-3510-4 LD-3510-8 EW-3510-4 EW-3510-8 EL-3510-4 EL-3510-8 GD-1765-4N GD-1765-8N GD-4765-4N GD-4765-4N KT-505W-4 KT-505W-8 KG-505W-4 KG-505W-8
Remarks:
Butterfly Valve, Wafer Body Butterfly Valve, Lug Body Butterfly Valve, Wafer Body Butterfly Valve, Lug Body Butterfly Valve, Grooved End Butterfly Valve, Grooved End Ball Valve, Threaded Ends Ball Valve, Grooved Ends
2, 212, 3, 4, 5, 6, 8, 10, 12
250 (1725) 250 (1725) 250 (1725) 250 (1725) 175 (1205) 300 (2070) 300 (2070) 300 (2070)
a, b, c, d, e
2, 212, 3, 4, 6, 8, 10, 12
a, b, c, d
2, 212, 3, 4, 6, 8, 10, 12
a, b, c, e
2, 212, 3, 4, 6, 8, 10, 12
a, b, c, f
212, 3, 4, 5, 6, 8, 10
a, b, c
212, 3, 4, 6, 8
a, b, c
a, b, c, d
2, 212
a, b, c
a. Aboveground, indoor or outdoor. b -4: no supervisory switches. c. -8: with supervisory switches. d. For mounting between ANSI bolted flanges. e. For use with ANSI, ISO NP10 and 16 or BS.10 D & E flanges. f. For use with metric flanges, NP10 and 16. g. With threads available to ANSI/ASME B1.20.1 and BS21 Pipe Thread Standards.
Butterfly Valve, Threaded Ends Butterfly Valve, Grooved Ends Butterflu Valve, Grooved Ends Butterfly Valve, Wafer Body Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body
175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070)
a, b a, b a, b a, b a, b a, b
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Model Number Product Type Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
SDBV-W
212, 3, 4, 6, 8 in.
175 (1205)
a, b
FM Approvals
1-161
Model Number
Product Type
Remarks
SDBV-G
Butterfly Valve, Grooved Ends Butterfly Valve, Threaded Connections Butterfly Valve, Grooved Ends
212, 3, 4, 6, 8 in.
a, b
SDBB-T
a, b
SDBB-G
Remarks:
2, 212 in.
a, b
a. Available with two supervisory switches. b. Approved for aboveground indoor use only.
Stockham Valves & Fittings, 2129 3rd Ave SE, Cullman AL 35055-5477
Fig. LD-52-UF, Fig. LG-52-UF. Wafer body (for mounting between bolted ANSI flanges). 4, 5, 6, 8, 10, 12 in. NPS. Fig. LD-62-UF, Fig. LG-62-UF. Drilled lug body. 4, 5, 6, 8, 10, 12 in. NPS. Fig. LD-72-UF, Fig. LG-72-UF. Drilled and tapped lug body, 4, 5, 6, 8, 10, 12 in. NPS. Fig. LD-82-UF, Fig. LG-82-UF. Cut grooved inlet and outlet body connections. 4, 6, 8 in. NPS. All valves are FM Approved for aboveground use only. Valves are available with one or two supervisory switches.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Model Number Product Type Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
212, 3, 4, 5, 8, 10 212, 3, 4, 5, 8, 10
a, b, c
a, b, c
a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor service. c. FM Approved for aboveground installations only.
Tyco Fire and Building Products, 1467 Elmwood Ave, Cranston RI 02910
Fig No. Product Type Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
BFV-N
2, 212, 3, 4, 5, 6, 8, 10, 12
a, b, c, d
BFV-N
2, 212, 3, 4, 6, 8, 10, 12
a, b, c
BFV-N
10
a, b
BFV-N
Remarks: a. b. c. d.
212, 3, 4, 6, 8
a, b
Aboveground, indoor or outdoor. Available with or without supervisory switches. For mounting between ANSI bolted flanges. For use with ANSI, ISO NP10 and 16 or BS.10 D & E flanges.
Series 702
212, 3, 4, 6, 8, 10
175 (1205)
a, b, c
Series 728
1, 114, 112, 2
350 (2415)
a, b, c
Series 705W
Remarks:
300 (2070)
a, b, c
FM Approvals
1-162
a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor service. c. FM Approved for aboveground installations only.
Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body Butterfly Valve, Grooved Ends Butterfly Valve, Wafer Body
a, b a, b a, b a, b
a. Available with dual supervisory switches. b. Approved for above ground, indoor and outdoor use only. Model Number Product Type Nominal Pipe Size, mm Rated Working Pressure, psi (kPa) Remarks
FBV-FP
3 4,
1, 114, 112, 2
175 (1205)
a, b, c
a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor use. c. FM Approved for aboveground installations only.
Type EVS Type EVBS Type EVBLS Type EVML Type EVTLS Type EVTLLS Type EVFS Type EVFL Type EVCS
Remarks:
Butterfly Valve, Wafer Body Butterfly Valve, Semi-Lugged Butterfly Valve, Semi-Lugged Butterfly Valve, Mono-Flanged Butterfly Valve, Lugged Butterfly Valve, Lugged Butterfly Valve, Flanged Ends Butterfly Valve, Flanged Ends Butterfly Valve, Semi-Lugged
50, 65, 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200 50, 65, 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200, 250, 300 50, 65, 80, 100, 125, 150, 200, 250, 300
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
a. Available with dual supervisory switches. b. FM Approved for indoor and outdoor service. c. FM Approved for aboveground installations only.
INDICATOR POSTS
Indicator posts are controls, extending aboveground, for operating underground sprinkler system valves. As an important feature of their design, a target or indicator, visible through an opening in the post, shows whether the valve is open or shut. The indicator post generally consists of a cast iron barrel, an extension flange which allows the height of the barrel to be regulated, and a wrought iron or mild steel stem which operates the underground valve and simultaneously moves the target. A telescoping union permits turning the stem from a constant height. Indicator posts are available for installation on non-rising stem gate valves. Unless otherwise specified, indicator posts are Approved for use on 4 through 14 in. NPS non-rising stem gate valves with an indicator post flange. In all new fire protection system installations, buried valves must open in a counterclockwise direction regardless of the direction the valves of the public water system open. An exception to this is when all other buried valves in a plant yard open in a clockwise direction. Then all new valves should open clockwise also.
FM Approvals
1-163
When some buried valves in a system open one way and some the other, all new valves should open counterclockwise. There may be exceptions to this when most valves in an extensive yard system open clockwise. In such cases, FM Global should be consulted regarding the proper direction of opening.
AVK International A/S, Bizonvej 3, Skovby DK-8464, Denmark
Model 34-00 Vertical Ind. Post, Adjustable. Model 34-80 Wall type.
American Darling Valve, Div American Cast Iron Pipe Co (ACIPCO), Box 2727, Birmingham AL 35202
Model IP-71. Fixed barrel.
American Flow Control, Div American Cast Iron Pipe Co (ACIPCO), Box 2727, Birmingham AL 35202
Model A240. Buried type, two-piece adjustable. Model A278. Floor-mounted type. Models A280, A281, A282. Wall type, various mounting configurations. Model A279. Miter gearing wall-mounted assembly. Model A-193-1, -2, -3. Coupling. For use with FM Approved post indicator valves. Model IP-71. Fixed barrel.
Clow Canada, Div Canada Pipe Co Ltd, 245 Industrial Dr, Grandview Industrial Park, Saint John, New Brunswick E2R 1A4 Canada
McAvity Cat. Fig. 2945. Nonadjustable Type. Vertical. McAvity Cat. Fig. 2945A. Adjustable Type. Vertical.
Clow Valve Co, Div McWane Inc, 902 S 2nd St, Oskaloosa IA 52577
Style 2945. Nonadjustable type. Style 2945A. Adjustable type. Style F5765K. Wall type.
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien Taiwan ROC
Fig. 800 Fig. 800 W. Wall type.
Fivalco (Qingdao) Co Ltd, 11 Shuangyuan Road Chengyang, Qingdao Shandong, PRC 266111
Model IP888. Vertical type. Model WP999. Wall Post.
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
Model 800. Adjustable barrel. Vertical. Model 810. Wall type.
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
Fig. Fig. Fig. Fig. Fig. 641-S. Wall post. 551. Right angle gear for use with Fig. 641-S. 641-14. Pit style post. Floor mounted. 2945. Vertical nonadjustable type post. 2945A. Vertical adjustable type post.
Lichfield Fire & Safety Equipment Co Ltd, 2nd Floor, Suite 4, Saturn Centre, Spring Rd, Ettingshall Rd, Wolverhampton WV4 WTX, United Kingdom
Fig. 800 Fig. 800 W. Wall Type.
Lien Hwa Iron Works Co Ltd, 112 Sec 2 Kuang Fu Rd, Sanchung Taipei Hsien 24113, Taiwan ROC
Fig. 130. Wall type. Fig. 135.
Mueller Canada Inc, 8069 Lawson Rd, Milton, Ontario L9T 5C4, Canada
Model C20806. Vertical adjustable type. Model C20808. Vertical nonadjustable type. Model C20813. Horizontal wall mounted.
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Fig. NF-PI800A. Fig. NF-PI800W. Wall Type.
FM Approvals
1-164
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
Model 800. Adjustable barrel. Vertical. Model 810. Wall type. Figure 800.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model RELPI-WALL. Wall Indicator Post. Model RELPI-UP. Indicator Post, Upright, Adjustable.
Shanghai Karon Valves Machinery Co Ltd, No 815 Deyuan Road Nanxiang, Jiading District Shanghai, PRC
Model RBLX Vertical Indicator Post, Adjustable. Model RWHX Wall type.
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Fig. 800. Fig. 800 W. Wall Type.
Stockham Valves & Fittings, 2129 3rd Ave SE, Cullman AL 35055-5477
Cat. Figs. G-950, G-950-A. Wall type. Cat. Figs. G-951, G-951-A.
Waterous Co, 125 Hardman Ave So, South Saint Paul MN 55075-1191
No. A240. Buried type, two-piece adjustable. No. A278. Floor-mounted type. No. A-193-1, -2, -3. Coupling. For use with FM Approved post indicator valves.
FM Approvals
1-165
Remarks
221 222 226 227 553 9241 9242 9246 9247 9276 9277 9551
Remarks: a. b. c. d. e. f. g.
Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valves
1, 114, 112, 2 1
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
f b, f g b, g f a a, b c b, c d, e b, d, e a
1 2, 3 4,
1 2, 3 4,
1, 114, 112, 2 1
1 2, 3 4,
1 2, 3 4,
1 2, 3 4,
1 2, 3 4,
1 2, 3 4,
1, 114, 112, 2 1
1 2, 3 4,
1 2, 3 4,
1, 114, 112, 2 1
1 2, 3 4,
1 2, 3 4,
1, 114, 112, 2
Valve supplied with female NPT pipe thread connections. Valve supplied with butterfly handle. Valve supplied with one male NPT and one female NPT pipe thread connection. Valve supplied with tube end connections. Manufacturers instructions shall be followed closely during installation to prevent damage to the valve seat. Valve supplied with Female ISO 7/1 thread connections. Valve supplied with one male ISO 7/1 and one female ISO 7/1 thread connection.
Compass Asia Inc, 11FL, No 165, Sec 4, Nanjing E Rd, Taipei 105, Taiwan
Product Designation Description Nominal Pipe Size, in.
1 2
Remarks
Lansdale Intl 900-02020 Lansdale Intl 900-02030 Lansdale Intl 900-02040 Lansdale Intl 900-02050 Lansdale Intl 900-02060 Lansdale Intl 900-02070 Lansdale Intl 900-02110 Lansdale Intl 900-02120 Lansdale Intl 900-02130 Lansdale Intl 900-02140 Lansdale Intl 900-02150 Lansdale Intl 900-02160
Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve
600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135)
a a a a a a b b b b b b
3 4
1 114 112 2
1 2
3 4
1 114 112 2
a. Valve supplied with female NPT pipe thread connections. b. Valve supplied with solder end connections.
FM Approvals
1-166
Remarks
94A
Remarks:
175 (1205)
a, d
a. Valve supplied with female NPT threaded end connections. d. Valve supplied with tube end connections.
Crane Supply, 615 Dixon Rd, Toronto, Ontario M9W 1H9, Canada
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34,
Remarks
CSC-9302 CSC-9322
Remarks:
1, 114, 112, 2
a b
1 2, 3 4,
1, 114, 112, 2
a. Valve supplied with female NPT pipe thread connections. b. Valve supplied with solder end connections.
Enolgas Bonomi SpA, Via Europa 227, 25062 Concesio (BS), Italy
Product Designation Description Nominal Pipe Size, in.
1 2
Remarks
Topic S1241 Topic S1241 Topic S1241 Topic S1241 Topic S020 Topic S020 Topic S020
Remarks: a. b. f. g. h. i. j.
Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve
580 (4000) 1 435 (3000) 363 (2500) 290 (2000) 1 435 (3000) 363 (2500) 290 (2000)
a a a a a, b, f, g, h, i, j a, b, f, g, h, i, j a, b, f, g, h, i, j
3 4,
114, 112 2
3 4,
114, 112 2
Valve supplied with female NPT pipe thread connections. Valve supplied with butterfly handle. Valve supplied with Aluminum lever handle. Valve supplied with fem/fem ISO 7/1 Rp thread connections. Valve supplied with fem/fem ISO 7/1 Rc thread connections. Valve supplied with male/fem ISO 7/1 Rp thread connections. Valve supplied with male/fem ISO 7/1 Rc thread connections.
Fire Protection Products Inc, 6241 Yarrow Drive, Suite A, Carlsbad CA 92011
Product Designation Description Nominal Pipe Size, in.
14, 12, 34,
Remarks
TrimFit TrimFit
Remarks:
Quick Opening Ball Type Valve Quick Opening Ball Type Valve
1, 114, 112 2
a a
Fortune Manufacturing Company Ltd, 11F No 222 Sec 5, Nanking E Rd, Taipei, Taiwan ROC
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34,
Remarks
220-TF
Ball Valve
1, 114, 112, 2
600 (4135)
FM Approvals
1-167
Product Designation
Description
Remarks
b a b
1 2, 3 4,
1, 114, 112, 2
a. Valve supplied with female NPT pipe thread connections b. Valve supplied with solder end connections.
Fratelli Pettinaroli SpA, Via Pianelli 38, 28017 San Maurizio dOpaglio Novara, Italy
Model T-100N-E. 14 through 2 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, brass valve stem and ball. Model T-100-C; 12 through 2 in.; 12 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections. Model T-100-SSN-E. 12 through 2 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, 316 stainless steel valve stem and ball. Model S-100N-E. 12 through 2 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. Model S-100-C. 12 through 2 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. All above 5 Models are available with: a) steel handle - 90 to open or close. b) aluminum tee handle - 90 to open or close. c) plastic top ball handle with one full turn to open or close. Model T-100. 14 through 1 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, brass valve stem and ball. Model T-100-C. 12 through 2 in.; 12 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections. Model T-100-SS. 12 through 1 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, 316 stainless steel valve stem and ball. Model S-100. 12 through 1 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. Model S-100-C. 12 through 2 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. All above with aluminum tee handle - 90 to open or close. Model T-100. 14 through 2 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, brass valve stem and ball. Model T-100-C. 12 through 2 in.; 12 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections. Model T-100-SS. 12 through 2 in.; 14 through 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Female pipe thread end connections, 316 stainless steel valve stem and ball. Model S-100. 12 through 2 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. Model S-100-C. 12 through 2 in.; 12, 34 in., 600 psi (4140 kPa) rated working pressure. 1 through 2 in., 500 psi (3450 kPa) rated working pressure. Tube by tube end connections, brass valve stem and ball. All above with plastic top ball handle with one full turn to open or close.
Fu San Machinery Co Ltd, 22 Lane 89, Sec 4 Chang-Mei Road, Ho-Mei Town Chang-Hua, Taiwan ROC
Fig. F1361FP. Ball type valves. 12, 34, 1, 114, 112, 2 in. Rated working pressure 600 psi (4130 kPa).
Fu San Valve (Suzhou) Limited, No. 1, Cheng Hu Zhong Rd, Wuzhong Economic Development Zone, Suzhou City, Jiangsu Province, China
Product Designation Description Nominal Pipe Size in.
12, 34,
Remarks
Model F1361FP
Remarks:
600 (4130)
a. Valves are available with threads to ANSI/ASME B1.20.1 and BS21 Pipe Thread Standards.
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Model Model Model Model Model Model Model R250D. 12, 34 in., 600 psi (4135 kPa) rated working pressure; 1 through 2 in., 500 psi (3445 kPa) rated working pressure. R850. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. NPT end connections. R858. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. Solder joint end connections. R910. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. NPT end connections. R918. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. Solder joint end connections. R850PR. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. NPT end connections. R858PR. 12 through 2 in., 600 psi (4135 kPa) rated working pressure. Solder joint end connections.
FM Approvals
1-168
Remarks
Model 8901
Remarks:
600 (4135)
IVR Valvole a sfera spa, Via Brughiera III n1, Loc. Piano Rosa, 28010 Boca (NO), Italy
Product Designation Description Nominal Pipe Size in.
12, 34,
Remarks
Model 45 FBV-3
Remarks:
1, 114, 112, 2
600 (4140)
a. Female pipe thread end connections with Standard Steel Handle 90 to open or close.
Remarks
S-100 S-100 S-100 S-100 S-100 S-100 S-100-C S-100-C S-100-C S-100-C T-100 T-100 T-100-C T-100-C T-100-SS T-100-SS T-100 T-100 T-100-C
Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve
600 (4140) 500 (3450) 6 00 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140)
b, e, g b, e, g b, c, e b, c, e b, d, e b, d, e b, c, e b, c, e b, d, e b, d, e b, f, g b, f, g f, g f, g f, g, h f, g, h b, c, f b, c, f c, f
1, 114, 112, 2
1 2,
1
12, 34
1, 112, 112, 2
12, 34
1, 114, 112, 2
12, 34
FM Approvals
1-169
Product Designation
Description
Remarks
T-100-C T-100-SS T-100-SS T-100 T-100 T-100-C T-100-C T-100-SS T-100-SS JF-100T
Remarks: a. b. c. d. e. f. g. h.
Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve Ball Valve
500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140) 500 (3450) 600 (4140)
c, f c, f, h c, f, h b, d, f b, d, f d, f d, f d, f, h d, f, h a
1, 114, 112, 2
Valves supplied with female NPT threaded end connections and BS21 Pipe Thread Standards. Brass valve stem and ball. All above with Aluminum Tee Handle 90 to open or close. All above with Plastic Slo-Ball Handle with one full turn to open or close. Tube by tube end connections. Female pipe thread end connections. All above with Standard Steel Handle 90 to open or close. 316 stainless steel valve stem and ball.
Karl DUNGS Inc, 524 Apollo Dr, Suite 10-30, Lino Lakes MN 55014
Model KH01/6, sizes 14, 38, 12, 34, 1, 114, 112 and 2 in. Female pipe thread end connections. 250 psi (1725 kPa) rated working pressure.
Legend Valve & Fitting, 51245 Filomena Drive, Shelby Township MI 48315
Product Designation Description Nominal Pipe Size in.
12, 34,
Remarks
T-1001 T-1004
a a
12, 34,
FM Approvals
1-170
Milwaukee Valve Company Inc, 16550 West Stratton Drive, New Berlin WI 53151
Product Designation Nominal Pipe Size, in.
12, 34, 1, 114, 112, 2 12, 34,
Description
Remarks
Quick Opening Butterfly Type Valve Quick Opening Ball Type Valve
a a
1, 114, 112, 2
Remarks
Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve Quick Opening Ball Type Valve
a, b a, b a, b a, b
114, 112, 2
a. Valves supplied with female NPT threaded end connections. b. Valves are available with threads to ANSI/ASME B1.20.1 and BS21 Pipe Thread Standards.
NIGO Industrial Co Ltd, No 9 Lane 93, Chang Lu Road, Changhua, Taiwan R.O.C.
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34, 1, 114, 112, 2 14
Remarks
a b c d, e
, 38, 12, 34, 1, 114, 112, 2 , 38, 12, 34, 1, 114, 112, 2 , 38, 12, 34, 1, 114, 112, 2
14
14
Valve supplied with female NPT pipe thread connections. Valve supplied with one male NPT and one female NPT pipe thread connection. Valve supplied with male NPT pipe thread connections. Valve supplied with tube end connections. Manufacturers instructions shall be followed closely during installation to prevent damage to the valve seat.
Ningbo Zhiqing Industrial Co Ltd, No. 12 Wai Huan (W.) Road, Yuelong Street, Ninghai County, Ningbo, 315600, China
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34,
Remarks
1, 114, 112, 2
a b b
1 2, 3 4,
1 2, 3 4,
a. Valve supplied with female NPT pipe thread connections. b. Valve supplied with solder end connections.
Potter-Roemer Inc, 15125 Proctor Avenue, Box 3527, City of Industry CA 91744-0527
Models 4405; 4407. 12, 34 in.; 600 psi (4135 kPa) rated working pressure. Models 4410, 4412, 4415, 4420. 1, 114, 112, 2 in.; 500 psi (3445 kPa) rated working pressure.
FM Approvals
1-171
Remarks
a a a
1 2, 3 4,
1 2, 3 4,
Rubinetterie Bresciane Bonomi SpA, Via Industralie 30, Box 31, 25065 Lumezzane SS Brescia, Italy
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34,
Remarks
Ball Valve, Threaded Ends Ball Valve, Threaded Ends Butterfly Valve, Threaded Ends Ball Valve, Threaded Ends Ball Valve, Threaded Ends Ball Valve, Press x Press Ball Valve Press x Thread
600 (4140) 600 (4140) 200 (1380) 400 (2760) 600 (4140) 200 (1380) 200 (1380)
a b a, b a a, b c a, b, c
1 2, 3 4,
1 2, 3 4,
1 2, 3 4,
1 2, 3 4,
a. Approved when supplied with female NPT end connections. b. Approved when supplied with ISO 7/1 female threaded ends. c. To be installed using Ridgid pressing tool Model CT-400 only
Rubinetterie Italiane Valvole, Via Dell Acacie 8-ZI, D4 28075 Grignasco NO, Italy
Series 4201. Sizes 12, 34, 1, 114, 112 in. NPS. 600 psi (4140 kPa) maximum rated working pressure. Size 2 in. NPS, 400 psi (2760 kPa) maximum rated working pressure. Female NPT end connections.
Rubinetterie Utensilerie Bonomi, Via Padana Superiore 27/29, Ciliverghe Di Mazzano, Brescia 25080, Italy
Model S.92. 14, 38, 12, 34, 1, 114, 112 and 2 in. 400 psi (2760 kPa) rated working pressure. Brass and chrome-plated finishes. NPT MF and FF end threaded. Model S.95. 14, 38, 12, 34, 1, 114, 112 and 2 in. 400 psi (2760 kPa) rated working pressure. Brass and chrome-plated finishes. NPT FF end threaded.
Toyo Valve Co Ltd, TT-2 Bldg, 8-1, 3-Chome, Nihonbashi-Ningyocho, Chuo-Ku, Tokyo 103-0013 Japan
Product Designation Description Nominal Pipe Size, in.
14, 38, 12, 34,
Remarks
a a, c b b, c
a. Valve supplied with female NPT pipe thread connections. b. Valve supplied with solder end connections. c. Valve supplied with wing handle.
VIR Valvoindustria Ing Rizzio SpA, Via Circonvallazione 10, 13018 Valduggia, Italy
Product Designation Description Nominal Pipe Size, in.
1 2, 3 4,
Remarks
340T 350T
a a
FM Approvals
1-172
Remarks
FBV-3C FBVS-3C
Remarks:
1, 114, 112, 2
a b
1 2, 3 4,
1, 114, 112, 2
a. Valve supplied with female NPT pipe thread connections. b. Valve supplied with solder end connections.
78FP
Remarks:
300 (2070)
a, b
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Model No. Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
78FP
Remarks:
300 (2070)
a, b
Ban Chang Hardware Co Ltd, No 168, Lane 432, Sec 3, Lu Ho Road, LuKang ChangHua Hsien 505, Taiwan
Product Designation Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
B120G
a. Supplied with grooved inlet and outlet.
250 (1725)
Model B
a. Resilient seat.
250 (1725)
FM Approvals
1-173
Clow Valve Co, Div McWane Inc, 902 S 2nd St, Oskaloosa IA 52577
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Flanged Ends Swing Check Valve, Flanged Ends Swing Check Valve, Grooved Ends Swing Check Valve, Wafer Type
a b b b
Model 375
a. Metal Seat.
3, 4, 6, 8,10
175 (1205)
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Flanged Ends Swing Check Valve, Grooved Ends
4, 6 4
a a, b
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien, Taiwan ROC
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve Flanged Ends Swing Check Valve Flanged Ends Dual Plate Check Valve Flanged Ends Dual Plate Check Valve Grooved Ends
3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8 3, 4, 6, 8
a b b, c b, c
Fire Protection Products Inc, 6241 Yarrow Drive, Suite A, Carlsbad CA 92009-1541
Product Designation Description Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Trim-Fit
Remarks b. Resilient Seat. c. No removable covers.
2, 212, 3, 4
300 (2070)
b, c
Firecheck DG
a. Resilient Seat.
300 (2070)
FM Approvals
1-174
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Model A140G**
Remarks a. Resilient seat.
250 (1725)
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends
4 212, 3 2, 212, 3, 4, 6
a a a
Model F517
Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Flanged Ends Swing Check Valve, Grooved Ends
2, 212, 3, 4, 6, 8
250 (1725) 250 (1725) 250 (1725) 175 (1205) 175 (1205) 175 (1205)
Model 7800FP
Model F52
Model F52
4, 6
Model F520
4, 6, 8
Model F5201
a. Resilient Seat.
4, 6, 8
Model 477J
Remarks a. Metal Seat.
3, 4, 6, 8, 10
175 (1205)
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Flanged Ends Swing Check Valve, Flanged Ends Swing Check Valve, Grooved Ends Swing Check Valve, Wafer Type
4, 6, 8
a b b b
FM Approvals
1-175
b. Resilient seat.
Lichfield Fire & Safety Equipment Co Ltd, 2nd Floor, Suite 4, Saturn Centre, Spring Rd, Ettingshall Rd, Wolverhampton WV4 WTX, United Kingdom
Model Model Model Model 763UM. 3 through 12 in. NPS, flanged swing check with bronze seat. 200 psi (1380 kPa) rated working pressure. 763UR. 3 through 12 in. NPS, flanged swing check with rubber faced clapper. 200 psi (1380 kPa) rated working pressure. 453UF**. 3, 4 and 6 in. NPS, flanged dual plate, rubber seat. 250 psi (1725 kPa) rated working pressure. 453UG**. 3, 4, 6 and 8 in. NPS, grooved end dual plate, rubber seat. 200 psi (1380 kPa) rated working pressure.
Lien Hwa Iron Works Co Ltd, 112 Section 2 Kuang Fu Rd, Sanchung, Taipei Hsien 24113, Taiwan ROC
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Figure 451B
Remarks a. Resilient Seat.
2, 212, 3, 4, 5, 6, 8, 10, 12
175 (1205)
Milwaukee Valve Company Inc, 16550 West Stratton Drive, New Berlin WI 53151
Series 1400. 2 through 10 in. NPS. Wafer style. Series 1800. 212 through 12 in. NPS. Globe style-flanged. Series 8800. 2 through 12 in. NPS. Oval disc-wafer style.
Swing Check Valve, Flanged Ends Swing Check Valve, Flanged Ends
a b
Swing Check Valve, Flanged Ends Swing Check Valve, Wafer Type Swing Check Valve, Flanged Ends Swing Check Valve Dual Disc-Grooved Ends Swing Check Valve, Dual Disc-Wafer Type Swing Check Valve, Dual Disc-Wafer Type
4, 6, 8, 12 2, 212, 3, 4, 5, 6, 8, 10
175 (1205) 200 (1380) 200 (1380) 250 (1725) 250 (1725) 200 (1380)
a a a a a b
National Fire Fighting Mfg, FZCO, Box 17014, Jebel Ali Free Zone, Dubai, UAE
Model Number Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Flanged End Connections Swing Check Valve, Flanged End Connections Swing Check Valve, Flanged End Connections Swing Check Valve, Grooved End Connections
3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8 3, 4, 6, 8
a b b, c, d b, c, d
FM Approvals
1-176
a. b. c. d.
Description
Remarks
FCG 300
a. Resilient Seat.
2, 212, 3, 4, 6, 8
300 (2070)
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Product Designation Nominal Pipe Size in./ mm Max Working Pressure, psi (kPa)
Description
Remarks
Swing Check Valve Grooved Ends Swing Check Valve Wafer Type Swing Check Valve Grooved Ends
a a, b
a. Resilient O-Ring Seat. No removable cover. b. Available with riser check valve trim package.
Ritepro Corporation, 12200 Albert Hudon, Montreal Quebec, H1G 3K7, Canada
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Wafer Type Swing Check Valve, Wafer Type
a a
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Model Number Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve, Flanged End Connections Swing Check Valve, Flanged End Connections Swing Check Valve, Flanged End Connections Swing Check Valve, Grooved End Connections
3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8 3, 4, 6, 8
a b b, c, d b, c, d
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
453U RCV
Remarks a. Resilient Seat. b. No removable covers.
Dual Plate Check Valve Grooved Ends Swing Check Valve Grooved ends
3, 4, 6, 8 212, 3, 4, 6
a, b a
FM Approvals
1-177
Siam Cast Iron Works Co Ltd, Samutsakorn Industrial Estate, Soi 7, 1/12 Moo 2, Rama II Rd, Tahsai, Muang, Samutsakorn 74000, Thailand
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Swing Check Valve Flanged ends Swing Check Valve Flanged ends Swing Check Valve Grooved ends Swing Check Valve Grooved ends
212, 3, 4, 6, 8, 10 12 212, 3, 4, 6, 8, 10 12
a, b a, b a, b a, b
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Product Designation Description Nominal Pipe Size in./ mm Max Working Pressure, psi (kPa) Remarks
Model S380
Remarks a. Resilient Seat.
250 (1725)
Model G-939
Remarks a. Metal Seat.
3, 4, 6, 8, 10
175 (1205)
Tong Kwang Valve Industrial Co Ltd, No. 1-1 Ming Chuan Rd, Ming-Sheng Li, Tansui, Taipei Hsien, Taiwan ROC
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Model 065U
Remarks a. Resilient Seat.
3, 4, 6, 8
175 (1205)
Model CV-2
Swing Check Valve Flanged or Grooved End Connections Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Riser Check Valve, Grooved Ends
4, 6, 8 212 2 1 2, 3, 4, 5, 6, 8, 10 3, 4, 5, 6, 8
a a, b a, b
2 1 2,
Val-Matic Valve & Mfg Corp, 905 Riverside Dr, Elmhurst IL 60126
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Series 1400
2, 212, 3, 4, 5, 6, 8, 10
200 (1380)
a, b
FM Approvals
1-178
Product Designation
Description
Remarks
Swing Check Valve, Flanged Ends Swing Check Valve, Grooved Ends Swing Check Valve, Wafer Style Swing Check Valve, Wafer Style
a, b b, c b, c b, c
Venus Fire Protection Ltd, 4105 Portland Blvd, Sherbrooke, Quebec J1L 1X9, Canada
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Astra Model CV Astra Model CVB-1 Astra Riser Model CVB-1 Astra Model CVB Astra Riser Model CVB Astra Model CVA Astra Riser Model CVA
a. Resilient Seat.
Swing Check Valve, Wafer Type Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends
4, 6 4 4 6 6 212, 3
2 1 2, 3
175 (1205) 250 (1725) 250 (1725) 175 (1205) 175 (1205) 250 (1725) 250 (1725)
a a a a a a a
Swing Check Valve, Cut Groove Swing Check Valve, Cut Groove
a a, b
Swing Check Valve, Cut Groove Swing Check Valve, Cut Groove
a a, b
Model F-1
Model G-1
Swing Check Valve, Flanged or Grooved Ends Swing Check Valve, Groove by Groove, Flange by Groove, or Flange by Flange ends Swing Check Valve, Groove by Groove, Flange by Groove, or Flange by Flange ends Swing Check Valve, Grooved Ends
212 2 1 2
a a
3, 4, 6, 8
250 (1725)
250 (1725)
FM Approvals
1-179
Product Designation
Description
Remarks
Swing Check Valve, Flanged or Grooved Ends Swing Check Valve, Grooved Ends Swing Check Valve, Grooved Ends
4, 6, 8 112, 2 4
a a a
Swing Check Valve, Flanged Ends Swing Check Valve, Flanged Ends
a, b a
Wilson & Cousins, 4390 Paletta Court, Burlington, Ontario L7L 5R2, Canada
Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa) Remarks
Model IE144G
Remarks
300 (2070)
a, b
Series 300 304.3, 304.4, 304.5, 304.6 306.3, 306.4, 306.5, 306.6 308.3, 308.4, 308.5, 308.6 310.3, 310.4, 310.5, 310.6
4 6 8 10
750 (2840) 1500 (5680) 3000 (11 355) 5000 (18 925)
Series 600 604.3, 604.4, 604.5, 604.6 606.3, 606.4, 606.5, 606.6 608.3, 608.4, 608.5, 608.6 610.3, 610.4, 610.5, 610.6 612.3, 612.4, 612.5, 612.6 618.1, 618.2
4 6 8 10 12 18
750 (2840) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500) 13,000 (49 210)
7.4 (51.0) 5.7 (39.5) 7.4 (51.0) 8.5 (58.5) 8.0 (55.0) 4.3 (29.5)
FM Approvals
1-180
Product Designation
Series 9000* 9004.1, 9204.1* 9006.1, 9206.1* 9008.1, 9208.1* 9010.1, 9210.1* 9012.1, 9212.1*
*250 psi (1725 kPa) working pressure.
4 6 8 10 12
750 (2840) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
7.8 (53.5) 4.3 (29.5) 4.3 (29.5) 3.9 (27.0) 3.5 (24.0)
Ban Chang Hardware Co Ltd, No 168, Lane 432, Sec 3, Lu Ho Road, LuKang ChangHua Hsien 505, Taiwan
Product Description Nominal Pipe Size, in. Flow Rate, gal/min (L/min) Friction Loss, psi (kPa)
B110*
Remarks
212
250 (945)
6.9 (47.5)
*250 psi (1725 kPa) rated working pressure. This Model is available with a FG suffix indicating that the valve is supplied with a grooved inlet by female threaded outlet. This Model is available with a FM suffix indicating that the valve is supplied with a male threaded inlet by female threaded outlet. This Model is available with a G suffix indicating that the valve is supplied with grooved inlet and outlet.
4 4 2 1 2 3 4 6
750 (2840) 750 (2840) 250 (945) 400 (1515) 750 (2840) 1500 (5680)
2.6 (18.0) 3.0 (20.5) 1.8 (12.5) 2.4 (16.5) 2.3 (16.0) 2.2 (15.0)
Series 580 Wafer Style* 2 212 3 4 5 6 8 10 200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 21.6 (149) 9.5 (67) 10 (69) 10.8 (75) 8.0 (55) 8.6 (59) 10.3 (71) 12.3 (85)
Series 581 Globe Style* 212 3 4 5 6 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3.9 (27) 5.2 (36) 6.1 (42) 3.7 (26) 5.0 (35)
FM Approvals
1-181
Product Designation
8 10 12
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
8.7 (60) 5.6 (39) 5.6 (39) 5.6 (39) 3.5 (24) 3.5 (24) 3.7 (26) 3.7 (26) 3.2 (22)
Clow Valve Co, Div McWane Inc, 902 S 2nd St, Oskaloosa IA 52577
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
329
4 5 6 8
636
4 5 6 8 10 12
750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
14.0 (96.5) 15.0 (103.5) 19.0 (131.0) 26.0 (179.5) 4.5 (31.0) 2.9 (20.0) 5.1 (35.0) 9.0 (62.0) 10 (65.5) 8.0 (55.0)
Duo-Chek U12HMP
4 6 8 10 12
750 (2840) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
1.8 (12.5) 1.3 (9.0) 1.8 (12.5) 2.0 (14.0) 2.0 (14.0)
Crane Stockham Valve Ltd, 6 Alexander Rd, Cregagh, Belfast Northern Ireland BT6 9HJ
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
Duo-Chek U12HMP
4 6 8
FM Approvals
1-182
Product Designation
10 12
250 psi (1725 kPa) working pressure.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
750 (2840)
4.2 (29.0)
Available with male inlet x female outlet threaded end connections and threaded male inlet x cut groove outlet end connections. 250 psi (1725 kPa) rated working pressure.
Fire Protection Products Inc, 6241 Yarrow Drive, Suite A, Carlsbad CA 92009-1541
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
TrimFit
2 212 3 4
Available with grooved grooved, male female threaded and male threaded grooved end connections. Resilient seat. 300 psi (2070 kPa) rated working pressure.
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
Model A140G
750 (2840)
3.8 (25.0)
Available with male inlet x female outlet threaded end connections and threaded male inlet x cut groove outlet end connections. 250 psi (1725 kPa) rated working pressure.
Grinnell or Gem F515* 4 NPT Male Outlet 4 NPT Female Outlet Grinnell or Gem F520, F5201
750 (2840)
2.55 (17.5)
4 6 8
750 (2840) 1500 (5680) 2700 (10 220) 250 (945) 200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500) 250 (945)
3.5 (24.0) 1.4 (9.5) 1.1 (7.5) 2.7 (19) 3.72 (26.0) 3.15 (22.5) 2.96 (20.5) 2.55 (17.5) 1.33 (9.0) 2.09 (14.5) 3.03 (21.0) 2.03 (14.0) 1.16 (8.0) 3.15 (22.5)
FM Approvals
1-183
Product Designation
Groeniger & Co, 27750 Industrial Blvd, Box 3629, Hayward CA 94545
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
750 (2840)
5.5 (38.0)
Kennedy Valve, Div McWane Inc, 1021 E Water St, Elmira NY 14901
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
706*
4 6 8
Milwaukee Valve Company Inc, 16550 West Stratton Drive, New Berlin WI 53151
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
Series 1400 Wafer Style 1402 1425 1403 1404 1405 1406 1408 1410 Series 1800 Globe Style 1825 1803 1804 1805 1806 1808 1810 1812 Series 8800 Dual Disc 8802 8825 8803 8804 8805 8806 8808 8810
2 212 3 4 5 6 8 10
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500) 200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925)
21.6 (149.0) 9.5 (65.5) 10.0 (69.0) 10.8 (74.5) 8.0 (55.0) 8.6 (59.0) 10.3 (71.0) 12.3 (85.0) 3.9 (27.0) 5.2 (36.0) 6.1 (42.0) 3.7 (25.5) 5.0 (34.5) 5.4 (37.0) 6.5 (45.0) 6.5 (45.0) 8.7 (60.0) 5.6 (38.5) 5.6 (38.5) 5.6 (38.5) 3.5 (24.0) 3.5 (24.0) 3.7 (25.5) 3.7 (25.5)
2 1 2 3 4 5 6 8 10 12
2 2 1 2 3 4 5 6 8 10
FM Approvals
1-184
Product Designation
8812
12
3.2 (22.0)
A-2102, A-2102-52
4 6 8
Fig. A-2103-52. 2 through 12 in. NPS. Cut groove. 250 psi (1725 kPa) rated working pressure.
Mueller Steam Specialty, Div Core Industries Inc, RR2 Box 44 Saint Pauls NC 28384
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
71*
2 212 3 4 5 6 8 10 12 14 16
72
2 2 1 2 3 4 5 6 8 10 12 14
101-AP
4 5 6 8 10
105-AP
4 5 6 8 10 12
200 (755) 300 (1135) 450 (1705) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500) 9500 (35 960) 13,000 (49 210) 200 (755) 300 (1135) 450 (1750) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500) 9500 (35 960) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
11 (76.0) 25 (172.5) 6 (41.5) 4.5 (31.0) 3 (20.5) 3.5 (24.0) 4 (27.5) 4.5 (31.0) 3.5 (24.0) 5 (34.5) 3 (20.5) 11 (76.0) 25 (172.5) 6 (41.5) 4.5 (31.0) 3 (20.5) 3.5 (24.0) 4 (27.5) 4.5 (31.0) 3.5 (24.0) 5 (34.5) 6.2 (42.5) 5.1 (35.0) 5.8 (40.0) 7.8 (54.0) 8.7 (60.0) 5.1 (35.0) 5.1 (35.0) 4.4 (30.5) 4.7 (32.5) 8.7 (60.0) 11.2 (77.0)
FM Approvals
1-185
Product Designation
107-AP**
4 6
*Rated working pressure 200 psi (1380 kPa) in 12 in. (305 mm) and smaller sizes; 150 psi (1035 kPa) in 14, 16 in. (355, 406 mm ) sizes. **Rated working pressure 400 psi (2760 kPa). Rated working pressure 285 psi (1965 kPa) when supplied with Carbon Steel body. Rated working pressure is 275 psi (1900 kPa) when supplied with stainless steel body. Rated working pressure is 225 psi (1550 kPa) when supplied with Bronze body.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
G*
212 3 4 6
Ritepro Corporation, 12200 Albert Hudon, Montreal, North Quebec H1G 3K7, Canada
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
212*, 312*
2 212 3 4 5 6 8 10 12
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
5.7 (39.5) 3.5 (24.0) 3.2 (22.0) 3.7 (25.5) 2.1 (14.5) 2.4 (16.5) 3.5 (24.0) 3.6 (25.0) 3.2 (22.0)
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
Model B*
*250 (1725 kPa) rated working pressure.
750 (2840)
2.6 (18.0)
Model 125WTI
2 212 3 4 5 6 8 10
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925)
1.3 (9.0) 1.3 (9.0) 2.4 (16.6) 1.0 (6.9) 2.0 (13.8) 2.4 (16.6) 2.6 (17.9) 2.9 (20.1)
FM Approvals
1-186
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
Grinnell CV-1F**
212 3 4 5 6 8 10
Grinnell CV-1FR**
2 1 2 3 4 5 6 8
TFP CV-1F**
212 3 4 5 6 8
TFP CV-1FR**
2 1 2 3 4 5 6 8
250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11355) 5000 (18 925) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11355) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11355) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11355)
2.6 (18) 4.3 (29) 4.0 (28) 2.7 (19) 2.2 (15) 2.2 (15) 1.3 (10) 2.6 (18) 4.3 (29) 4.0 (28) 2.7 (19) 2.2 (15) 2.2 (15) 2.6 (18) 4.3 (29) 4.0 (28) 2.7 (19) 2.2 (15) 2.2 (15) 2.6 (18) 4.3 (29) 4.0 (28) 2.7 (19) 2.2 (15) 2.2 (15)
**300 psi (2070 kPA) rated working pressure. Supplied trimmed as Riser Check Valve.
90
4 6 8
67*
750 (2840) 1500 (5680) 3000 (11 355) 750 (2840) 750 (2840)
4.5 (31.0) 3.8 (26.0) 7.0 (48.5) 5.5 (38.0) 5.5 (38.0)
68TXG***
Note: Figure 67-Cut groove end connections. Figure 68-NPT male inlet and NPT female outlet connections. *250 psi (1725 kPa) working pressure. ***4 in. male NPT inlet X grooved outlet end connections.
Val-Matic Valve & Mfg Corp, 905 Riverside Dr, Elmhurst IL 60126
Product Designation Valve Size, in. Flow Rate,gal/min (dm3/min) Friction Loss, psi (kPa)
200 (755)
21.6 (149.0)
FM Approvals
1-187
Product Designation
212 3 4 5 6 8 10
250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925)
9.5 (67.0) 10 (65.5) 10.8 (74.5) 8.0 (55.0) 8.6 (59.0) 10.3 (71.0) 12.3 (85.0)
Series 1800 Globe Style* 180212 1803 1804 1805 1806 1808 1810 1812
212 3 4 5 6 8 10 12
250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
3.9 (27.0) 5.2 (36.0) 6.1 (42.0) 3.7 (25.5) 5.0 (34.5) 5.4 (37.0) 6.5 (45.0) 6.5 (45.0)
Series 8800 Dual Disc Wafer Style* 8802 880212 8803 8804 8805 8806 8808 8810 8812
2 212 3 4 5 6 8 10 12
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
8.7 (60.0) 5.6 (38.5) 5.6 (38.5) 5.6 (38.5) 3.5 (24.0) 3.5 (24.0) 3.7 (25.5) 3.7 (25.5) 3.2 (22.0)
Series VM 1400 Wafer Style* VM1402 VM140212 VM1403 VM1404 VM1405 VM1406 VM1408 VM1410
2 212 3 4 5 6 8 10
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925)
21.6 (149.0) 9.5 (67.0) 10 (65.5) 10.8 (74.5) 8.0 (55.0) 8.6 (59.0) 10.3 (71.0) 12.3 (85.0)
Series 8800 BBN SSF Dual Disc Wafer Style* 8802 BBN SSF 880212 BBN SSF
2 212 3 4 5 6
8803 BBN SSF 8804 BBN SSF 8805 BBN SSF 8806 BBN SSF
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680)
8.7 (60.0) 5.6 (38.5) 5.6 (38.5) 5.6 (38.5) 3.5 (24.0) 3.5 (24.0)
FM Approvals
1-188
Product Designation
8 10 12
Series 8800 GBN SSF Dual Disc Wafer Style* 8802 GBN SSF 880212GBN SSF 8803 GBN SSF 8804 GBN SSF 8805 GBN SSF 8806 GBN SSF 8808 GBN SSF 8810 GBN SSF 8812 GBN SSF
2 212 3 4 5 6 8 10 12
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
8.7 (60.0) 5.6 (38.5) 5.6 (38.5) 5.6 (38.5) 3.5 (24.0) 3.5 (24.0) 3.7 (25.5) 3.7 (25.5) 3.2 (22.0)
Series 8800 GAN SSF Dual Disc Wafer Style* 8802 GAN SSF 880212 GAN SSF
2 212 3 4 5 6 8 10 12
8803 GAN SSF 8804 GAN SSF 8805 GAN SSF 8806 GAN SSF 8808 GAN SSF 8810 GAN SSF 8812 GAN SSF
*200 psi (1380 kPa) working pressure.
200 (755) 250 (945) 400 (1515) 750 (2840) 1000 (3785) 1500 (5680) 3000 (11 355) 5000 (18 925) 7000 (26 500)
8.7 (60.0) 5.6 (38.5) 5.6 (38.5) 5.6 (38.5) 3.5 (24.0) 3.5 (24.0) 3.7 (25.5) 3.7 (25.5) 3.2 (22.0)
Style 717*
4 5 6 8 139 mm 165 mm
750 (2840) 1000 (3875) 1500 (5675) 3000 (11 625) 1000 (3875) 1500 (5675)
3.53 (24) 1.97 (14) 2.00 (14) 2.31 (16) 1.97 (14) 2.00 (14)
Style 717*
4 5 6 8 139 mm
750 (2840) 1000 (3875) 1500 (5675) 3000 (11 625) 1000 (3875)
3.53 (24) 1.97 (14) 2.00 (14) 2.31 (16) 1.97 (14)
FM Approvals
1-189
Product Designation
165 mm 10 12
*250 psi (1725 kPa) working pressure.
Size, gal (Liters) 2.5 (9.46) 5.0 (18.93) 10 (37.85) 25 (94.6) 40 (151.40) 80 (302.80) 120 (454.20) 150 (568) 2.5 (9.46) 5.0 (18.93) 10 (37.85) 25 (94.6) 40 (151.40) 80 (302.80) 120 (454.20) 250 (950) 500 (1900)
Rated Working Pressure, psi (kPa) 275 (1895) 275 (1895) 275 (1895) 275 (1895) 275 (1895) 275 (1895) 275 (1895) 275 (1895) 600 (4135) 600 (4135) 600 (4135) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 275 (1895) 275 (1895)
Notes a a a c c c c c b b b d d d d c c
BACKFLOW PREVENTERS
Backflow preventers are used in connections between public water supplies and fire protection systems to prevent reverse flow. Where health authorities require the installation of backflow preventers, FM Approved models should be used.
FM Approvals
1-190
These backflow preventers have been evaluated for reliability from a fire protection standpoint. No attempt has been made to determine their suitability to ensure the public health. Unless otherwise noted in the listing, these devices have 175 psi (1205 kPa) rated working pressure and are limited to horizontal installations.
FM Approvals
1-191
Product Designation
Friction Loss, psi (kPa) 4.3 (29.5) 6.2 (42.5) 6.6 (45.5) 3.5 (24) 3.8 (26) 5.2 (36) 5.6 (39) 9.0 (62) 14.2 (100) 7.4 (51.0) 6.4 (44.1) 5.8 (40.0) 8.6 (59.3) 3.3 (22.7) 2.7 (18.5) 3.6 (25) 4.1 (28.5) 8.0 (55) 5.8 (40.0) 10.7 (74.0) 19.3 (133.0) 7.0 (48.5) 14.1 (97.0) 19.2 (132.5) 5.3 (36.5) 7.2 (49.5) 10.0 (69.0) 5.9 (41.0) 8.6 (59.5) 10.9 (75.0) 4.4 (30.0) 3.1 (21.4) 5.1 (35.1) 3.8 (26.2) 6.2 (42.7) 12.3 (85)
10
212
10
FM Approvals
1-192
Product Designation
Friction Loss, psi (kPa) 4.4 (30.3) 8.9 (61.3) 14.9 (102.7) 6.7 (46) 12.1 (83.4) 17.8 (122.7) 3.9 (26.9) 2.9 (20.0) 5.7 (39.3) 3.0 (20.7) 6.7 (46.2) 14.6 (100.7) 4.8 (33.1) 11.0 (75.8) 18.2 (125.5) 7.1 (49) 12.3 (85) 19.4 (134) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65) 3.1 (21) 7.8 (54) 18.1 (125) 3.5 (24) 10.6 (75) 17.8 (125) 3.2 (22) 7.5 (28) 14.6 (100) 3.8 (26) 8.7 (60) 17.0 (115)
2001 SS, 2001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
150 (570) 3 250 (945) 400 (1895) 250 (945) 4 500 (1895) 750 (2840) 1000 (3785) 6 1500 (5680) 2000 (7570) 1500 (5680) 8 2000 (7570) 2500 (17235) 150 (570)
2001 SS, 2001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
2001 SS, 2001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
2001 SS, 2001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
212
10
FM Approvals
1-193
Product Designation
Friction Loss, psi (kPa) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 8.3 (57) 19.8 (135) 3.0 (21) 11.3 (78) 19.2 (130) 3.2 (22) 7.9 (54) 15.2 (105) 4.1 (28) 9.8 (68) 19.8 (135) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65) 2.8 (19) 3.9 (27) 11.0 (76) 2.8 (19) 5.8 (40) 9.0 (62) 2.4 (17) 3.6 (25) 6.4 (44) 3.8 (26) 8.7 (60) 17.0 (115)
Colt 200N/200Na
212
Colt 200N/200Na
Colt 200N/200Na
Colt 200N/200Na
Colt 200N
Colt 200N
10
212
10
FM Approvals
1-194
Product Designation
Friction Loss, psi (kPa) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 5.1 (35) 15.2 (105) 3.0 (21) 6.1 (42) 9.5 (66) 2.7 (19) 4.3 (30) 7.8 (54) 4.1 (28) 9.8 (68) 19.8 (135)
Maxim 200N/200Na
212
Maxim 200N/200Na
Maxim 200N/200Na
Maxim 200N
Maxim 200N
Maxim 200N
10
FM Approvals
1-195
Friction Loss, psi (kPa) 6.1 (42) 7.1 (49) 7.6 (52) 5.6 (40) 6.9 (50) 7.2 (50) 6.3 (45) 6.7 (45) 6.9 (50) 4.5 (30) 5.2 (35) 7.0 (50) 8.3 (55) 13.2 (90) 20.6 (140) 12.5 (86) 21.1 (145) 29.6 (204) 8.6 (60) 12.2 (85) 16.2 (110) 6.2 (45) 7.5 (50) 9.0 (60) 6.9 (50) 8.4 (60) 11.4 (80) 4.9 (35) 5.8 (40) 7.4 (50) 9.1 (65) 14.6 (100) 23.2 (160) 12.5 (85) 21.1 (145) 29.6 (205)
10
212
10
212
FM Approvals
1-196
Product Designation
Friction Loss, psi (kPa) 9.0 (60) 13.1 (90) 18.0 (125) 5.5 (40) 7.5 (50) 8.6 (60) 6.9 (50) 7.6 (50) 9.1 (65) 7.7 (55) 9.6 (65) 11.1 (75) 9.1 (65) 15.0 (105) 23.6 (165) 6.0 (40) 12.7 (90) 15.3 (105) 8.5 (60) 12.3 (85) 16.8 (115) 5.8 (40) 6.0 (40) 12.2 (85) 4.8 (33) 5.8 (40) 13.2 (90) 5.7 (40) 12.3 (85) 24.2 (165) 6.1 (42) 14.2 (100) 26.2 (180) 2.3 (15) 6.9 (50) 15.7 (110)
10
212
10
212
FM Approvals
1-197
Product Designation
Friction Loss, psi (kPa) 6.2 (45) 14.0 (95) 25.3 (175)
10
Febco Models 870*, 870v* 870*, 870v* (n-shaped configuration for horizontal installation)
Febco Models 870*, 870v* 870*, 870v* (n-shaped configuration for horizontal installation)
Febco Models 870*, 870v* 870*, 870v* (n-shaped configuration for horizontal installation)
Febco Models 870*, 870v* 870*, 870v* (n-shaped configuration for horizontal installation)
FM Approvals
1-198
Product Designation Febco Models 870*, 870v* 870*, 870v* (n-shaped configuration for horizontal installation)
Friction Loss, psi (kPa) 5.6 (40) 5.8 (40) 7.5 (50)
10
*Model Nos. 870 and 870v (in the n-shaped configuration) are available with optional FLGxFLG (212, 3, 4, 6, 8 and 10 in.); MJMJ (3, 4, 6, 8 and 10 in.) or FLGxMJ (3, 4, 6, 8 and 10 in.) Valve Setter Elbows. The above friction loss data was obtained by assemblies which employed Valve Setter Elbows.
Product Designation Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
Friction Loss, psi (kPa) 5.2 (35) 4.1 (30) 5.7 (40) 4.6 (30) 3.5 (25) 5.3 (35) 2.9 (20) 5.8 (40) 10.2 (70) 3.3 (25) 4.7 (30) 6.7 (45) 4.4 (30) 6.3 (45) 9.2 (65) 5.4 (35) 6.4 (45) 9.0 (60) 4.4 (30) 5.5 (40) 7.5 (50) 5.1 (35) 6.7 (45) 8.5 (60) 4.4 (30) 9.0 (60) 15.0 (105) 3.5 (25) 6.6 (45) 10.5 (70)
212
Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
Febco Models 870v, 850 870v (z-shaped configuration for vertical installation)
10
212
FM Approvals
1-199
Product Designation
Friction Loss, psi (kPa) 3.3 (25) 4.2 (30) 6.4 (45) 4.1 (30) 5.1 (35) 6.3 (45) 4.7 (30) 6.2 (45) 7.7 (55) 4.5 (30) 7.2 (50) 15.2 (105) 3.3 (25) 3.8 (25) 4.7 (30) 3.6 (25) 4.5 (30) 6.2 (45)
212
Hersey Meters, Division of Mueller Group Inc, Hwy 70 Box 128 Cleveland NC 27013
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 300 (1135) No. 2 3 400 (1515) 500 (1895) 500 (1895) No. 2 4 750 (2840) 1000 (3785) 1000 (3785) No. 2 6 1500 (5680) 1750 (6625) 1500 (5680) No. 2 8 2000 (7570) 2500 (9465) 3000 (11 355) No. 2 10 4000 (15 140) 5000 (18 925) Friction Loss, psi (kPa) 7.9 (55) 11.6 (80) 16.9 (115) 7.0 (50) 9.5 (65) 14.6 (100) 7.2 (50) 12.9 (90) 18.3 (125) 5.4 (40) 6.9 (50) 10.6 (75) 11.3 (80) 16.1 (110) 20.2 (140)
FM Approvals
1-200
FM Approvals
1-201
Product Designation
Friction Loss, psi (kPa) 4.8 (35) 3.3 (25) 6.7 (45) 4.2 (30) 5.4 (35) 7.8 (55) 6.8 (45) 6.0 (40) 10.6 (75) 5.4 (35) 5.7 (40) 11.6 (80) 12.6 (85) 19.5 (135) 23.6 (165) 7.4 (50) 9.6 (65) 12.7 (90) 6.3 (43.5) 5.9 (40.5) 5.8 (40) 6.6 (45.5) 2.3 (16) 2.7 (18.5) 3.6 (25) 4.1 (28.5) 8.0 (55) 4.3 (29.5) 6.2 (42.5) 6.6 (45.5) 3.5 (24) 3.8 (26) 5.2 (36) 5.6 (39) 9.0 (62) 14.2 (100)
770DC
770DC
10
212
10
FM Approvals
1-202
Product Designation
Friction Loss, psi (kPa) 7.3 (50) 7.8 (55) 11.8 (80) 8.4 (60) 13.5 (95) 21.5 (150) 4.4 (30) 3.1 (21) 5.1 (35) 3.8 (26) 6.2 (43) 12.3 (85) 4.4 (30) 8.9 (61) 14.9 (103) 6.7 (47) 12.1 (83) 17.8 (123) 3.9 (27) 2.9 (20) 5.7 (39) 3.0 (21) 6.7 (46) 14.6 (101) 4.8 (33) 11.0 (76) 18.2 (126) 7.1 (49) 12.3 (85) 19.4 (134) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65)
212
775, 775 SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
150 (570) 3 250 (945) 400 (1895) 250 (945) 4 500 (1895) 750 (2840) 1000 (3785) 6 1500 (5680) 2000 (7570) 1500 (5680) 8 2000 (7570) 2500 (17235) 150 (570)
775, 775 SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
775, 775 SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
775, 775 SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
212
FM Approvals
1-203
Product Designation
Friction Loss, psi (kPa) 3.1 (21) 7.8 (54) 18.1 (125) 3.5 (24) 10.6 (75) 17.8 (125) 3.2 (22) 7.5 (28) 14.6 (100) 3.8 (26) 8.7 (60) 17.0 (115) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 8.3 (57) 19.8 (135) 3.0 (21) 11.3 (78) 19.2 (130) 3.2 (22) 7.9 (54) 15.2 (105) 4.1 (28) 9.8 (68) 19.8 (135) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65)
10
212
10
212
FM Approvals
1-204
Product Designation
Friction Loss, psi (kPa) 2.8 (19) 3.9 (27) 11.0 (76) 2.8 (19) 5.8 (40) 9.0 (62) 2.4 (17) 3.6 (25) 6.4 (44) 3.8 (26) 8.7 (60) 17.0 (115) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 5.1 (35) 15.2 (105) 3.0 (21) 6.1 (42) 9.5 (66) 2.7 (19) 4.3 (30) 7.8 (54) 4.1 (28) 9.8 (68) 19.8 (135)
10
212
10
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 100 (380) 350 (horizontal and vertical installation) 212 200 (760) 300 (1135) Friction Loss, psi (kPa) 5.8 (40) 6.6 (45) 8.5 (60)
FM Approvals
1-205
Product Designation
Friction Loss, psi (kPa) 6.6 (45) 9.4 (65) 14.6 (100) 5.6 (40) 12.3 (85) 21.3 (145) 3.7 (25) 6.7 (45) 9.9 (70) 2.8 (20) 4.1 (30) 6.5 (45) 4.4 (30) 8.3 (57) 13.2 (91) 5.5 (40) 12.2 (85) 21.3 (145) 3.7 (25) 7.2 (50) 10.5 (70) 3.2 (20) 4.6 (30) 6.9 (50) 6.1 (40) 7.6 (50) 10.1 (70) 7.3 (50) 9.0 (60) 13.2 (90) 3.6 (25) 6.5 (45) 12.5 (85) 3.4 (25) 5.1 (35) 11.5 (80)
10
212
FM Approvals
1-206
Product Designation
Friction Loss, psi (kPa) 3.2 (20) 4.2 (30) 6.1 (40) 4.7 (30) 9.8 (70) 17.4 (120) 6.0 (40) 7.5 (50) 9.7 (65) 8.9 (60) 10.5 (70) 12.3 (85) 5.4 (35) 6.1 (40) 8.0 (55) 4.8 (35) 5.2 (35) 6.1 (40) 5.3 (35) 6.0 (40) 6.9 (50) 5.6 (40) 5.8 (40) 6.5 (45)
10
950
212
950
950
950
950
950
10
FM Approvals
1-207
Product Designation
Friction Loss, psi (kPa) 14.2 (98) 16.9 (116) 21.7 (150) 13.0 (90) 16.7 (115) 22.8 (157) 12.8 (89) 17.5 (120) 21.0 (145) 11.8 (82) 13.1 (91) 15.0 (104) 11.9 (82) 13.8 (95) 15.4 (106) 12 (83) 9.7 (67) 12.7 (87.5) 10.8 (74.5) 8.9 (61.5) 9.4 (65) 8.2 (56.5) 10 (69) 16.3 (112.5) 8.8 (60.5) 11.7 (80.5) 12.8 (88.5) 12.3 (85) 14.1 (95) 16.0 (110) 17.7 (120) 28.6 (195) 36.8 (255) 6.5 (45) 8.9 (60) 14.8 (100)
4000 CIV
4000 CIV
4000 CIV
4000 CIV
4000 CIV
10
212
10
4001SS, 4001 SS RS
FM Approvals
1-208
Product Designation
Friction Loss, psi (kPa) 8.9 (60) 15.4 (105) 26.0 (180) 8.3 (55) 10.7 (75) 23.0 (160) 8.9 (60) 9.1 (65) 15.5 (105) 8.9 (60) 15.9 (110) 26.4 (180) 9.9 (70) 11.1 (75) 23.5 (160) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (57) 7.9 (54) 12.3 (85) 7.2 (50) 11.2 (77) 21.0 (145) 7.6 (52) 14.5 (100) 22.8 (155) 7.5 (52) 11.7 (81) 19.7 (135) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125)
4001SS, 4001 SS RS
4001SS, 4001 SS RS
4001SS, 4001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
100 (380) 3 250 (945) 500 (1895) 250 (945) 4 500 (1895) 750 (2840) 750 (2840) 6 1000 (3785) 1500 (5680) 150 (570)
4001SS, 4001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
4001SS, 4001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
Colt 400
212
Colt 400
Colt 400
Colt 400
Colt 400
Colt 400
10
Colt 400N/400Z
212
FM Approvals
1-209
Product Designation
Friction Loss, psi (kPa) 8.2 (56) 8.0 (55) 12.9 (89) 7.8 (54) 12.7 (88) 23.0 (160) 7.8 (54) 12.4 (85) 19.0 (130) 8.0 (55) 12.5 (86) 19.5 (135) 7.8 (54) 12.0 (83) 17.8 (125) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (56) 7.9 (54) 12.3 (85) 9.0 (62) 7.4 (51) 12.2 (84) 7.7 (53) 9.2 (63) 12.2 (84) 7.4 (51) 7.8 (54) 11.1 (76) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125)
Colt 400N/400Z
Colt 400N/400Z
Colt 400N/400Z
Colt 400N/400Z
Colt 400N/400Z
10
Maxim 400
212
Maxim 400
Maxim 400
Maxim 400
Maxim 400
Maxim 400
10
Maxim 400N/400Z
212
FM Approvals
1-210
Product Designation
Friction Loss, psi (kPa) 8.2 (56) 8.0 (55) 12.9 (89) 9.5 (66) 8.8 (61) 19.8 (135) 8.0 (55) 10.4 (72) 14.4 (100) 7.5 (52) 8.8 (61) 14.0 (96) 7.8 (54) 12.0 (83) 17.8 (125)
Maxim 400N/400Z
Maxim 400N/400Z
Maxim 400N/400Z
Maxim 400N/400Z
Maxim 400N/400Z
10
FM Approvals
1-211
Product Designation
Friction Loss, psi (kPa) 10.3 (70) 14.4 (100) 20.4 (140) 9.9 (70) 15.2 (105) 21.8 (150) 8.7 (60) 14.3 (100) 19.5 (135) 9.9 (70) 15.2 (105) 21.9 (150) 8.3 (55) 14.0 (95) 19.3 (135) 9.8 (70) 15.1 (105) 22.0 (150) 11.2 (75) 13.1 (90) 18.0 (125) 10.0 (70) 11.7 (80) 15.1 (105) 9.0 (60) 13.7 (95) 24.2 (165) 11.1 (75) 20.2 (140) 32.5 (225) 7.0 (50) 10.2 (70) 17.0 (115) 9.5 (65) 16.0 (110) 27.5 (190)
Model RP
Model RP
10
10
10
Model 4D-700
212
Model 4D-700
Model 4D-700
Model 4D-700
Model 4D-700
Model 4D-700
10
FM Approvals
1-212
Febco Models 880*, 880v*, 880*, 880v* (n-shaped configuration for horizontal installation)
Febco Models 880*, 880v*, 880*, 880v* (n-shaped configuration for horizontal installation)
Febco Models 880*, 880v*, 880*, 880v* (n-shaped configuration for horizontal installation)
Febco Models 880*, 880v*, 880*, 880v* (n-shaped configuration for horizontal installation)
Febco Models 880*, 880v*, 880*, 880v* (n-shaped configuration for horizontal installation)
*Model Nos. 880 and 880v (in the n-shaped configuration) are available with optional FLGxFLG (212, 3, 4, 6, 8 and 10 in.); MJMJ (3, 4, 6, 8 and 10 in.) or FLGxMJ (3, 4, 6, 8 and 10 in.) Valve Setter Elbows. The above friction loss data was obtained by assemblies which employed Valve Setter Elbows.
FM Approvals
1-213
Product Designation
Friction Loss, psi (kPa) 10.3 (70) 10.8 (75) 12.1 (85) 10.1 (70) 10.1 (70) 12.8 (90) 10.9 (75) 10.8 (75) 12.3 (85) 7.5 (50) 8.0 (55) 10.5 (75) 11.7 (80) 13.2 (90) 14.9 (105) 11.4 (80 12.6 (85) 14.5 (100) 10.8 (75) 10.9 (75) 12.5 (85) 11.3 (80) 12.3 (85) 14.3 (100) 8.4 (60) 11.5 (80) 16.7 (115) 9.6 (65) 9.7 (65) 10.4 (70) 10.6 (75) 11.5 (80) 12.6 (85)
212
10
860
212
860
860
860
860
FM Approvals
1-214
Hersey Meters, Division of Mueller Group Inc, Hwy 70 Box 128, Cleveland NC 27013
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 200 (755) 6CM 212 250 (945) 300 (1135) 300 (1135) 6CM 3 400 (1515) 450 (1705) 500 (1895) 6CM 4 750 (2840) 800 (3030) 1000 (3785) 6CM 6 1500 (5680) 1750 (6625) 1500 (5680) 6CM 8 2000 (7570) 2500 (9465) 3000 (11 355) 6CM 10 4000 (15 140) 5000 (18 925) Friction Loss, psi (kPa) 13.8 (95) 15.1 (105) 17.3 (120) 14.6 (100) 16.5 (115) 17.7 (120) 13.6 (95) 15.6 (110) 18.2 (125) 12.9 (90) 17.8 (125) 20.3 (140) 13.9 (95) 15.8 (110) 18.4 (125) 14.2 (100) 18.1 (125) 19.6 (135)
FM Approvals
1-215
FM Approvals
1-216
Product Designation
Friction Loss, psi (kPa) 13.3 (90) 17.3 (120) 26.1 (180) 11.1 (75) 17.3 (120) 26.3 (180) 12 (83) 9.7 (67) 12.7 (87.5) 10.8 (74.5) 8.9 (61.5) 9.4 (65) 8.2 (56.5) 10 (69) 16.3 (112.5) 8.8 (60.5) 11.7 (80.5) 12.8 (88.5) 12.3 (85) 14.1 (95) 16.0 (110) 17.7 (120) 28.6 (195) 36.8 (255) 6.5 (45) 8.9 (60) 14.8 (100) 8.9 (60) 15.4 (105) 26.0 (180) 8.3 (55) 10.7 (75) 23.0 (160) 8.9 (60) 9.1 (65) 15.5 (105)
992RP
992RP
10
994, 994 SR
212
994, 994 SR
994, 994 SR
994, 994 SR
994, 994 SR
994, 994 SR
10
995, 995 SR
995, 995 SR
995, 995 SR
995, 995 SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
FM Approvals
1-217
Product Designation 995, 995 SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations) 995, 995 SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
Friction Loss, psi (kPa) 8.9 (60) 15.9 (110) 26.4 (180) 9.9 (70) 11.1 (75) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (57) 7.9 (54) 12.3 (85) 7.2 (50) 11.2 (77) 21.0 (145) 7.6 (52) 14.5 (100) 22.8 (155) 7.5 (52) 11.7 (81) 19.7 (135) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 7.8 (54) 12.7 (88) 23.0 (160) 7.8 (54) 12.4 (85) 19.0 (130)
500 (1895) 750 (2840) 750 (2840) 1000 (3785) 150 (570)
212
10
212
FM Approvals
1-218
Product Designation
Friction Loss, psi (kPa) 8.0 (55) 12.5 (86) 19.5 (135) 7.8 (54) 12.0 (83) 17.8 (125) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (56) 7.9 (54) 12.3 (85) 9.0 (62) 7.4 (51) 12.2 (84) 7.7 (53) 9.2 (63) 12.2 (84) 7.4 (51) 7.8 (54) 11.1 (76) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 9.5 (66) 8.8 (61) 19.8 (135) 8.0 (55) 10.4 (72) 14.4 (100)
10
212
10
212
FM Approvals
1-219
Product Designation
Friction Loss, psi (kPa) 7.5 (52) 8.8 (61) 14.0 (96) 7.8 (54) 12.0 (83) 17.8 (125)
10
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 100 (380) 375 212 200 (760) 300 (1135) 300 (1135) 375 3 400 (1515) 500 (1895) 500 (1895) 375 4 750 (2840) 1000 (3785) 750 (2840) 375 6 1250 (4730) 1500 (5680) 1500 (1580) 375 8 2000 (7570) 2500 (9465) 2000 (7570) 375 10 2750 (10 410) 3250 (12 300) 500 (1895) 375A 4 750 (2840) 1000 (3785) 750 (2840) 375A 6 1250 (4730) 1500 (5680) 1500 (5680) 375A 8 2000 (7570) 2500 (9465) Friction Loss, psi (kPa) 12.8 (90) 14.3 (100) 16.9 (115) 14.4 (100) 16.1 (110) 19.5 (135) 9.0 (60) 13.1 (90) 20.8 (145) 7.3 (50) 10.2 (70) 12.6 (85) 10.8 (75) 11.9 (80) 13.5 (95) 11.0 (76) 13.6 (94) 18.7 (129) 9.6 (65) 14.5 (10) 22.5 (155) 8.2 (55) 10.0 (70) 14.0 (95) 12.2 (85) 12.4 (85) 13.9 (95)
FM Approvals
1-220
Product Designation 475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
Friction Loss, psi (kPa) 11.6 (80) 14.0 (95) 18.0 (125) 12.2 (85) 12.9 (90) 14.2 (100) 10.5 (70) 10.1 (70) 15.4 (105) 7.4 (50) 9.0 (60) 14.0 (95) 9.9 (70) 11.2 (75) 13.7 (95) 11.3 (80) 16.2 (110) 21.0 (145) 11.2 (75) 13.3 (90) 15.3 (105) 11.1 (75) 12.7 (90) 14.2 (100) 10.1 (70) 11.3 (80) 13.1 (90) 10.6 (75) 12.0 (85) 13.8 (95) 12.0 (85) 12.8 (90) 13.9 (95) 10.5 (70) 10.9 (75) 11.4 (80)
212
475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
475, 475V (475 is an n-shaped configuration for horizontal installation, 475V is an z-shaped configuration for vertical installation)
10
975
212
975
975
975
975
975
10
FM Approvals
1-221
FM Approvals
1-222
Product Designation
Friction Loss, psi (kPa) 4.3 (29.5) 6.2 (42.5) 6.6 (45.5) 3.5 (24) 3.8 (26) 5.2 (36) 5.6 (39) 9.0 (62) 14.2 (100) 7.4 (51.0) 6.4 (44.1) 5.8 (40.0) 8.6 (59.3) 3.3 (22.7) 2.7 (18.5) 3.6 (25) 4.1 (28.5) 8.0 (55) 7.5 (52.0) 11.3 (78.0) 18.7 (129.0) 9.0 (62.0) 14.2 (98.0) 19.2 (132.5) 8.8 (61.0) 10.0 (69.0) 12.2 (84.0) 9.9 (68.5) 11.2 (77.5) 12.7 (87.5) 4.4 (30.0) 3.1 (21.4) 5.1 (35.1) 3.8 (26.2) 6.2 (42.7) 12.3 (85)
10
212
10
FM Approvals
1-223
Product Designation
Friction Loss, psi (kPa) 4.4 (30.3) 8.9 (61.3) 14.9 (102.7) 6.7 (46) 12.1 (83.4) 17.8 (122.7) 3.9 (26.9) 2.9 (20.0) 5.7 (39.3) 3.0 (20.7) 6.7 (46.2) 14.6 (100.7) 4.8 (33.1) 11.0 (75.8) 18.2 (125.5) 7.1 (49) 12.3 (85) 19.4 (134) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65) 3.1 (21) 7.8 (54) 18.1 (125) 3.5 (24) 10.6 (75) 17.8 (125) 3.2 (22) 7.5 (28) 14.6 (100) 3.8 (26) 8.7 (60) 17.0 (115)
3001 SS, 3001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
150 (570) 3 250 (945) 400 (1895) 250 (945) 4 500 (1895) 750 (2840) 1000 (3785) 6 1500 (5680) 2000 (7570) 1500 (5680) 8 2000 (7570) 2500 (17235) 150 (570)
3001 SS, 3001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
3001 SS, 3001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
3001 SS, 3001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
212
10
FM Approvals
1-224
Product Designation
Friction Loss, psi (kPa) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 8.3 (57) 19.8 (135) 3.0 (21) 11.3 (78) 19.2 (130) 3.2 (22) 7.9 (54) 15.2 (105) 4.1 (28) 9.8 (68) 19.8 (135) 4.0 (28) 6.0 (41) 10.8 (75) 3.2 (22) 4.0 (28) 9.3 (65) 2.8 (19) 3.9 (27) 11.0 (76) 2.8 (19) 5.8 (40) 9.0 (62) 2.4 (17) 3.6 (25) 6.4 (44) 3.8 (26) 8.7 (60) 17.0 (115)
Colt 300N/300Na
212
Colt 300N/300Na
Colt 300N/300Na
Colt 300N/300Na
Colt 300N
Colt 300N
10
212
10
FM Approvals
1-225
Product Designation
Friction Loss, psi (kPa) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 5.1 (35) 15.2 (105) 3.0 (21) 6.1 (42) 9.5 (66) 2.7 (19) 4.3 (30) 7.8 (54) 4.1 (28) 9.8 (68) 19.8 (135)
Maxim 300N/300Na
212
Maxim 300N/300Na
Maxim 300N/300Na
Maxim 300N
Maxim 300N
Maxim 300N
10
FM Approvals
1-226
Product Designation
Friction Loss, psi (kPa) 8.5 (60) 12.3 (85) 16.8 (115) 16.2 (110) 12.5 (85) 21.1 (145) 29.6 (205) 5.9 (40) 13.1 (90) 18.0 (125) 6.4 (45) 11.1 (75) 16.0 (110) 8.5 (60) 12.3 (85) 16.8 (115) 9.0 (60) 10.6 (75) 13.9 (95) 8.4 (58) 11.7 (81) 19.2 (132) 8.6 (59) 14.9 (103) 20.7 (143) 8.5 (60) 10.8 (75) 14.1 (95) 8.6 (60) 10.6 (75) 13.9 (95) 5.8 (40) 6.0 (40) 12.2 (85)
10
3000 (11 355) 3500 (13 250) 3500 (13 250) 1500 (5680)
10
10
300 (1135) 3 400 (1515) 500 (1895) 500 (1895) 4 750 (2840) 1000 (3785) 1000 (3785) 6 1500 (5680) 1750 (6625) 1500 (5680) 8 2000 (7570) 2500 (9465) 2000 (7570) 10 3000 (11 355) 4000 (15 140) 150 (570)
212
FM Approvals
1-227
Product Designation
Friction Loss, psi (kPa) 4.8 (33) 5.8 (40) 13.2 (90) 5.7 (40) 12.3 (85) 24.2 (165) 6.1 (42) 14.2 (100) 26.2 (180) 2.3 (15) 6.9 (50) 15.7 (110) 6.2 (45) 14.0 (95) 25.3 (175)
10
FM Approvals
1-228
Product Designation Febco Models 876*, 876v* 876*, 876v* (n-shaped configuration for horizontal installation)
Friction Loss, psi (kPa) 7.0 (55) 6.5 (45) 10.5 (75) 5.2 (35) 6.8 (45) 11.5 (80) 5.5 (40) 9.0 (60) 13.5 (95) 5.3 (35) 6.0 (40) 7.6 (50) 1.4 (50) 7.1 (50) 6.9 (50)
Febco Models 876*, 876v* 876*, 876v* (n-shaped configuration for horizontal installation)
Febco Models 876*, 876v* 876*, 876v* (n-shaped configuration for horizontal installation)
Febco Models 876*, 876v* 876*, 876v* (n-shaped configuration for horizontal installation)
Febco Models 876*, 876v* 876*, 876v* (n-shaped configuration for horizontal installation)
10
*Model Nos. 876 and 876v (in the n-shaped configuration) are available with optional FLGxFLG (212, 3, 4, 6, 8 and 10 in.); MJMJ (3, 4, 6, 8 and 10 in.) or FLGxMJ (3, 4, 6, 8 and 10 in.) Valve Setter Elbows. The above friction loss data was obtained by assemblies which employed Valve Setter Elbows.
Product Designation Febco Model 876v 876v (z-shaped configuration for vertical installation)
Friction Loss, psi (kPa) 8.5 (60) 6.8 (45) 7.7 (55) 8.0 (55) 5.9 (40) 6.8 (45) 4.4 (30) 6.2 (45) 8.5 (60) 4.3 (30) 4.6 (30) 7.5 (50) 4.8 (35) 6.5 (45) 9.0 (60) 7.0 (50) 8.0 (55) 9.4 (65)
212
10
FM Approvals
1-229
Product Designation
Friction Loss, psi (kPa) 6.8 (45) 7.0 (50) 8.1 (55) 7.1 (50) 8.3 (55) 9.9 (70) 5.5 (40) 9.7 (65) 15.2 (105) 4.5 (30) 7.1 (50) 10.4 (70) 4.4 (30) 4.6 (30) 5.9 (40) 6.4 (45) 6.7 (45) 7.8 (55) 7.0 (50) 8.0 (55) 9.4 (65) 4.1 (30) 4.8 (35) 9.1 (65) 4.5 (30) 4.1 (30) 4.0 (30) 4.2 (30) 4.4 (30) 5.5 (40)
212
212
Hersey Meters, Division of Mueller Group Inc, Hwy 70 Box 128 Cleveland NC 27013
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 300 (1135) DDC II 3 400 (1515) 500 (1895) Friction Loss, psi (kPa) 10.0 (70) 12.2 (85) 16.0 (110)
FM Approvals
1-230
Product Designation
Friction Loss, psi (kPa) 9.1 (65) 11.6 (80) 20.3 (140) 9.5 (65) 12.8 (90) 17.5 (120) 8.0 (55) 8.8 (60) 10.6 (75) 10.4 (70) 13.0 (90) 16.7 (115)
DDC II
DDC II
DDC II
DDC II
10
FM Approvals
1-231
Product Designation
Friction Loss, psi (kPa) 4.5 (30) 6.9 (50) 9.6 (65) 7.0 (50) 6.6 (45) 8.4 (60) 9.1 (65) 8.1 (55) 8.1 (55) 4.6 (30) 7.6 (50) 13.3 (90) 5.3 (35) 5.3 (35) 7.7 (55) 7.0 (50) 9.1 (65) 17.1 (120)
770DCDC
10
007DCDA
The 2 in. Model No. 007DCDA is FM Approved for use in the horizontal and vertical flow-up orientations. 50 (190) 774DCDA, 774 DCDA SR (horizontal and vertical installations) 212 150 (570) 250 (945) 100 (380) 774DCDA, 774 DCDA SR (horizontal and vertical installations) 3 250 (945) 300 (1135) 250 (945) 774DCDA, 774 DCDA SR (horizontal and vertical installations) 4 500 (1895) 700 (2650) 1000 (3785) 774DCDA, 774 DCDA SR (horizontal and vertical installations) 6 1250 (4730) 1300 (4920) 1500 (5680) 774DCDA, 774 DCDA SR (horizontal and vertical installations) 8 2000 (7570) 2500 (9465) 6.3 (43.5) 5.9 (40.5) 5.8 (40) 6.6 (45.5) 2.3 (16) 2.7 (18.5) 3.6 (25) 4.1 (28.5) 8.0 (55) 4.3 (29.5) 6.2 (42.5) 6.6 (45.5) 3.5 (24) 3.8 (26) 5.2 (36)
FM Approvals
1-232
Product Designation
Friction Loss, psi (kPa) 5.6 (39) 9.0 (62) 14.2 (100) 7.3 (50) 7.8 (55) 11.8 (80) 8.5 (60) 13.5 (95) 21.5 (150) 4.4 (30) 3.1 (21) 5.1 (35) 3.8 (26) 6.2 (43) 12.3 (85) 4.4 (30) 8.9 (61) 14.9 (103) 6.7 (47) 12.1 (83) 17.8 (123) 3.9 (27) 2.9 (20) 5.7 (39) 3.0 (21) 6.7 (46) 14.6 (101) 4.8 (33) 11.0 (76) 18.2 (126) 7.1 (49) 12.3 (85) 19.4 (134) 4.0 (28) 6.0 (41) 10.8 (75)
10
212
775DCDA, 775 DCDA SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
150 (570) 3 250 (945) 400 (1895) 250 (945) 4 500 (1895) 750 (2840) 1000 (3785) 6 1500 (5680) 2000 (7570) 1500 (5680) 8 2000 (7570) 2500 (17235) 150 (570) 212 250 (950) 400 (1515)
775DCDA, 775 DCDA SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
775DCDA, 775 DCDA SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
775DCDA, 775 DCDA SR (n-shaped configuration for horizontal installation; z-shaped configuration for vertical installation)
FM Approvals
1-233
Product Designation Silver Eagle 757 DCDA/757a DCDA (horizontal and vertical installations)
Friction Loss, psi (kPa) 3.2 (22) 4.0 (28) 9.3 (65) 3.1 (21) 7.8 (54) 18.1 (125) 3.5 (24) 10.6 (75) 17.8 (125) 3.2 (22) 7.5 (28) 14.6 (100) 3.8 (26) 8.7 (60) 17.0 (115) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 8.3 (57) 19.8 (135) 3.0 (21) 11.3 (78) 19.2 (130) 3.2 (22) 7.9 (54) 15.2 (105) 4.1 (28) 9.8 (68) 19.8 (135) 4.0 (28) 6.0 (41) 10.8 (75)
10
212
10
FM Approvals
1-234
Product Designation Silver Eagle 767 DCDA/767a DCDA (horizontal and vertical installations)
Friction Loss, psi (kPa) 3.2 (22) 4.0 (28) 9.3 (65) 2.8 (19) 3.9 (27) 11.0 (76) 2.8 (19) 5.8 (40) 9.0 (62) 2.4 (17) 3.6 (25) 6.4 (44) 3.8 (26) 8.7 (60) 17.0 (115) 4.5 (31) 7.7 (53) 14.8 (100) 3.2 (22) 3.8 (26) 8.1 (56) 3.1 (21) 5.1 (35) 15.2 (105) 3.0 (21) 6.1 (42) 9.5 (66) 2.7 (19) 4.3 (30) 7.8 (54) 4.1 (28) 9.8 (68) 19.8 (135)
10
212
10
FM Approvals
1-235
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 100 (380) 350DA (horizontal and vertical installation) 212 200 (760) 300 (1135) 300 (1135) 350DA (horizontal and vertical installation) 3 400 (1515) 450 (1705) 500 (1895) 350DA (horizontal and vertical installation) 4 750 (2840) 1000 (3785) 750 (2840) 350DA (horizontal and vertical installation) 6 1250 (4730) 1500 (5680) 1500 (5680) 350DA (horizontal and vertical installation) 8 2000 (7570) 2500 (9465) 2000 (7570) 350DA (horizontal and vertical installation) 10 2750 (10 410) 3500 (13 250) 500 (1895) 350ADA (horizontal and vertical installation) 4 750 (2840) 1000 (3785) 750 (2840) 350ADA (horizontal and vertical installation) 6 1250 (4730) 1500 (5680) 1500 (5680) 350ADA (horizontal and vertical installation) 8 2000 (7570) 2500 (9465) 250 (945) 450DA (n-shaped configuration for horizontal installations) 4 500 (1895) 750 (2840) 750 (2840) 450DA (n-shaped configuration for horizontal installations) 6 1000 (3785) 1500 (5680) Friction Loss, psi (kPa) 9.2 (65) 9.4 (65) 13.3 (90) 9.9 (70) 14.0 (95) 17.0 (115) 5.5 (40) 12.3 (85) 21.3 (145) 3.3 (25) 6.8 (45) 10.4 (70) 4.2 (30) 5.8 (40) 8.9 (60) 6.0 (41) 11.2 (77) 18.1 (125) 5.5 (40) 12.2 (85) 21.3 (145) 3.7 (25) 7.4 (50) 11.1 (75) 4.6 (30) 6.3 (45) 9.3 (65) 3.6 (25) 6.5 (45) 12.5 (85) 3.4 (25) 5.1 (35) 11.5 (80)
FM Approvals
1-236
Product Designation
Friction Loss, psi (kPa) 5.4 (40) 6.9 (50) 10.2 (70) 6.7 (45) 14.6 (100) 19.9 (135) 6.8 (47) 7.6 (52) 9.8 (68) 7.0 (48) 7.9 (54) 9.7 (67) 8.5 (60) 9.5 (65) 10.6 (75) 7.6 (50) 8.8 (60) 10.4 (70) 8.8 (60) 9.9 (70) 12.2 (85) 11.5 (80) 14.8 (100) 17.0 (115)
10
950DA
212
950DA
950DA
950DA
950DA
950DA
10
FM Approvals
1-237
Product Designation
Friction Loss, psi (kPa) 15.0 (105) 15.2 (105) 17.3 (120) 13.0 (90) 14.7 (100) 14.9 (105) 13.8 (95) 14.7 (100) 17.3 (120) 14.9 (105) 16.1 (110) 20.0 (140) 14.2 (100) 15.5 (105) 17.2 (120) 12 (83) 9.7 (67) 12.7 (87.5) 10.8 (74.5) 8.9 (61.5) 9.4 (65) 8.2 (56.5) 10 (69) 16.3 (112.5) 8.8 (60.5) 11.7 (80.5) 12.8 (88.5) 6.5 (45) 8.9 (60) 14.8 (100) 8.9 (60) 15.4 (105) 26.0 (180) 8.3 (55) 10.7 (75) 23.0 (160)
5000 CIV
5000 CIV
5000 CIV
5000 CIV
5000 CIV
10
212
5001SS, 5001 SS RS
5001SS, 5001 SS RS
5001SS, 5001 SS RS
FM Approvals
1-238
Product Designation 5001SS, 5001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
Friction Loss, psi (kPa) 8.9 (60) 9.1 (65) 15.5 (105) 8.9 (60) 15.9 (110) 26.4 (180) 9.9 (70) 11.1 (75) 23.5 (160) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (57) 7.9 (54) 12.3 (85) 7.2 (50) 11.2 (77) 21.0 (145) 7.6 (52) 14.5 (100) 22.8 (155) 7.5 (52) 11.7 (81) 19.7 (135) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 7.8 (54) 12.7 (88) 23.0 (160)
5001SS, 5001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
5001SS, 5001 SS RS (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
Colt 500
212
Colt 500
Colt 500
Colt 500
Colt 500
Colt 500
10
Colt 500N/500Z
212
Colt 500N/500Z
Colt 500N/500Z
FM Approvals
1-239
Product Designation
Friction Loss, psi (kPa) 7.8 (54) 12.4 (85) 19.0 (130) 8.0 (55) 12.5 (86) 19.5 (135) 7.8 (54) 12.0 (83) 17.8 (125) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (56) 7.9 (54) 12.3 (85) 9.0 (62) 7.4 (51) 12.2 (84) 7.7 (53) 9.2 (63) 12.2 (84) 7.4 (51) 7.8 (54) 11.1 (76) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 9.5 (66) 8.8 (61) 19.8 (135)
Colt 500N/500Z
Colt 500N/500Z
Colt 500N/500Z
10
Maxim 500
212
Maxim 500
Maxim 500
Maxim 500
Maxim 500
Maxim 500
10
Maxim 500N/500Z
212
Maxim 500N/500Z
Maxim 500N/500Z
FM Approvals
1-240
Product Designation
Friction Loss, psi (kPa) 8.0 (55) 10.4 (72) 14.4 (100) 7.5 (52) 8.8 (61) 14.0 (96) 7.8 (54) 12.0 (83) 17.8 (125)
Maxim 500N/500Z
Maxim 500N/500Z
Maxim 500N/500Z
10
FM Approvals
1-241
Product Designation
Friction Loss, psi (kPa) 11.1 (75) 20.2 (140) 32.5 (225) 7.0 (50) 10.2 (70) 17.0 (115) 8.8 (60) 16.0 (110) 29.0 (200)
Model 4D-700
Model 4D-700
Model 4D-700
10
FM Approvals
1-242
Product Designation
Friction Loss, psi (kPa) 15.0 (105) 15.2 (105) 17.3 (120) 13.0 (90) 14.7 (100) 14.9 (105) 13.8 (95) 14.7 (100) 17.3 (120) 14.9 (105) 16.1 (110) 20.0 (140) 14.2 (100) 15.5 (105) 17.2 (120) 13.0 (90) 12.7 (90) 12.3 (85) 14.1 (95) 13.2 (90) 14.1 (95) 11.3 (80) 11.8 (80) 13.3 (90) 11.2 (75) 9.8 (70) 9.0 (60) 14.5 (100) 14.4 (100) 15.1 (105) 13.3 (90) 12.3 (85) 16.5 (110) 13.0 (90) 12.1 (85) 12.9 (90)
909RPDA
909RPDA
909RPDA
909RPDA
909RPDA
10
990RPDA
990RPDA
990RPDA
992RPDA
992RPDA
992RPDA
992RPDA
10
FM Approvals
1-243
Product Designation
Friction Loss, psi (kPa) 12 (83) 9.7 (67) 12.7 (87.5) 10.8 (74.5) 8.9 (61.5) 9.4 (65) 8.2 (56.5) 10 (69) 16.3 (112.5) 8.8 (60.5) 11.7 (80.5) 12.8 (88.5) 6.5 (45) 8.9 (60) 14.8 (100) 8.9 (60) 15.4 (105) 26.0 (180) 8.3 (55) 10.7 (75) 23.0 (160) 8.9 (60) 9.1 (65) 15.5 (105) 8.9 (60) 15.9 (110) 26.4 (180) 9.9 (70) 11.1 (75) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (57) 7.9 (54) 12.3 (85)
212
995RPDA, 995 RPDA SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
100 (380) 3 250 (945) 500 (1895) 250 (945) 4 500 (1895) 750 (2840) 750 (2840) 6 1000 (3785) 150 (570)
995RPDA, 995 RPDA SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations) 995RPDA, 995 RPDA SR (n-shaped configuration for horizontal installations and z-shaped configuration for vertical installations)
212
FM Approvals
1-244
Product Designation
Friction Loss, psi (kPa) 7.2 (50) 11.2 (77) 21.0 (145) 7.6 (52) 14.5 (100) 22.8 (155) 7.5 (52) 11.7 (81) 19.7 (135) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 7.8 (54) 12.7 (88) 23.0 (160) 7.8 (54) 12.4 (85) 19.0 (130) 8.0 (55) 12.5 (86) 19.5 (135) 7.8 (54) 12.0 (83) 17.8 (125) 9.0 (62) 9.2 (63) 12.6 (87) 8.2 (56) 7.9 (54) 12.3 (85)
10
212
10
212
FM Approvals
1-245
Product Designation
Friction Loss, psi (kPa) 9.0 (62) 7.4 (51) 12.2 (84) 7.7 (53) 9.2 (63) 12.2 (84) 7.4 (51) 7.8 (54) 11.1 (76) 7.5 (52) 13.0 (90) 23.1 (160) 9.1 (63) 11.2 (77) 18.3 (125) 8.2 (56) 8.0 (55) 12.9 (89) 9.5 (66) 8.8 (61) 19.8 (135) 8.0 (55) 10.4 (72) 14.4 (100) 7.5 (52) 8.8 (61) 14.0 (96) 7.8 (54) 12.0 (83) 17.8 (125)
10
212
10
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Product Designation Valve Size, in. Flow Rate, gal/min (dm3/min) 100 (380) 375DA 212 200 (760) 300 (1135) Friction Loss, psi (kPa) 15.0 (105) 16.8 (115) 18.7 (130)
FM Approvals
1-246
Product Designation
Friction Loss, psi (kPa) 16.5 (115) 21.0 (145) 25.5 (175) 9.0 (60) 13.1 (90) 20.8 (145) 7.3 (50) 10.2 (70) 12.6 (85) 12.0 (80) 13.2 (90) 15.5 (150) 12.7 (88) 16.6 (114) 22.2 (153) 9.0 (60) 13.1 (90) 20.8 (145) 7.3 (50) 10.2 (70) 12.6 (85) 12.0 (80) 13.2 (90) 15.5 (150) 10.5 (95) 10.1 (70) 15.4 (105) 7.4 (50) 9.0 (60) 14.0 (95) 11.7 (80) 13.7 (95) 17.2 (120) 13.2 (90) 14.4 (100) 16.0 (110)
375DA
375DA
375DA
375DA
375DA
10
375ADA
375ADA
375ADA
475DA, 475DAV (475DA is an n-shaped configuration for horizontal installation; 475DAV is an z-shaped configuration for vertical installation) 475DA, 475DAV (475DA is an n-shaped configuration for horizontal installation; 475DAV is an z-shaped configuration for vertical installation) 475DA, 475DAV (475DA is an n-shaped configuration for horizontal installation; 475DAV is an z-shaped configuration for vertical installation)
250 (945) 4 500 (1895) 750 (2840) 750 (2840) 6 1000 (3785) 1500 (5680) 1500 (5680) 8 2000 (7570) 2500 (9465) 50 (190)
975DA
212
FM Approvals
1-247
Product Designation
Friction Loss, psi (kPa) 12.9 (90) 13.9 (95) 16.4 (115) 13.4 (90) 14.5 (100) 17.5 (120) 13.2 (90) 14.2 (100) 16.0 (110) 14.0 (95) 15.5 (105) 17.1 (120) 14.3 (100) 14.8 (100) 15.3 (105)
975DA
975DA
975DA
975DA
975DA
10
Aquamaster FC (Fire Service Coned) Model Code MM/GAabcdefgUh4Aijklmn Reduced Throat Bore Fire Service Meter Assembly 3, 4, 6, 8 and 10 in. NPS (80, 100, 150, 200, and 250 mm). 95-240 VAC and/or battery powered display. 175 psi (1205 kPa) rated working pressure.
a = Language code. b = 0080, 0100, 0150, 0200, or 0250 bore diameter (mm). c = Display and sensor configuration. d = 0, A, B, C, D, or L power supply. e = 2 or C enclosure options. f = Cable length. g = Label type. h = Cable connection type. I = Electrode material. j = Options. k = Communication protocol. l = Data protocol. m = Pressure transducer option. n = Pressure span.
FM Approvals
1-248
Hersey Meters, Division of Mueller Group Inc, Hwy 70, Box 128, Cleveland NC 27013
Models MFM 11/MCT 11, MFM 11/MHR, MFM 11/MVR. 3, 4, 6, 8, 10 in. (76, 102, 152, 203, 254 mm). Model MFM II/Horizon. 4, 6, 8, 10, 12 in. (102, 152, 203, 254, 305 mm). Horizon Fire Service Turbine Meter Assembly. 4, 6 and 8 in. NPS. Consists of Mueller Steam Model 595 Strainer and a Hersey Horizon turbine meter.
Neptune Technology Group Inc, 1600 Alabama Hwy 229 S, Tallassee AL 36078
HP Fire Service Turbine Cold Water Meter. 3, 4, 6, 8, 10 in. These meters must be installed and are supplied with an Approved strainer. HP Protectus III Fire Service and Cold Water Meter. 4, 6, 8, 10 in. Consists of strainer, fire service turbine, detector check valve and bypass loop with gate valve, check valve and trident meter for low flows.
FM Approvals
1-249
2000 DC
10
1000 DCV
10
1000 SS DCV
10
300 (1135) 500 (1895) 750 (2840) 1000 (3785) 1300 (4920) 1500 (5680) 2500 (9465) 3000 (11 355) 3100 (11 735) 4000 (15 140) 4900 (18 550) 5500 (20 820) 500 (1895) 750 (2840) 1000 (3785) 1000 (3785) 1500 (5680) 1750 (6625) 1500 (5680) 1750 (6625) 2500 (9465) 3000 (11 355) 4000 (15 140) 5000 (18 925) 1500 (5680) 1750 (6625) 2500 (9465) 3000 (11 355) 4000 (15 140) 5000 (18 925)
7.9 (54.5) 8.2 (56.5) 11.5 (78.5) 9.1 (62.5) 9.8 (67.5) 10.2 (70.5) 10.7 (74.0) 15.5 (107.0) 16/1 (111.0) 25.5 (176.0) 36.0 (248.0) 44.0 (303.5) 2.9 (20.0) 3.0 (21.0) 5.1 (35.5) 4.0 (27.5) 3.6 (25.0) 3.0 (21.0) 3.4 (23.5) 3.3 (23.0) 3.2 (22.0) 1.9 (13.0) 1.9 (13.0) 2.5 (17.0) 3.4 (23.5) 3.3 (23.0) 3.2 (22.0) 1.9 (13.0) 1.9 (13.0) 2.5 (17.0)
FM Approvals
1-250
Product Designation
10
10
Hersey Meters, Division of Mueller Group Inc, Hwy 70, Box 128, Cleveland NC 27013
DC 2 140 (530) 175 (660) 220 (835) 250 (945) 400 (1515) 600 (2270) 500 (1895) 750 (2840) 1000 (3785) 1000 (3785) 1500 (5680) 2000 (7570) 2000 (7570) 3000 (11 355) 1.1 (8.0) 1.4 (10.0) 1.7 (12.0) 1.0 (7.0) 1.9 (13.0) 4.6 (32.0) 1.7 (12.0) 2.5 (17.0) 3.3 (23.0) 1.6 (11.0) 2.2 (15.0) 2.6 (18.0) 1.7 (12.0) 2.4 (16.5)
EDC
FM Approvals
1-251
Product Designation
10
EDC II
EDC III
10
EDC IV
10
4000 (15 140) 2250 (8515) 4500 (17 035) 6750 (25 550) 2000 (7570) 3000 (11 355) 4000 (15 140) 500 (1905) 750 (2840) 1000 (3785) 1000 (3785) 1500 (5700) 2000 (7550) 1500 (5700) 2000 (7550) 2500 (9455) 2250 (8515) 4500 (17 035) 6000 (22 710) 200 (757) 400 (1514) 600 (2270) 800 (3030) 500 (1893) 750 (2839) 1000 (3785) 1000 (3785) 1500 (5678) 2000 (7570) 1500 (5678) 3000 (11 355) 4000 (15 140) 2250 (8516) 4500 (16 843) 6750 (25 550)
3.1 (21.5) 1.6 (11.0) 2.2 (15.0) 2.6 (18.0) 1.7 (12.0) 2.4 (16.5) 3.1 (21.5) 2.5 (17.0) 2.6 (18.0) 2.0 (14.0) 2.5 (17.0) 3.0 (21.0) 4.0 (27.5) 1.8 (12.5) 2.0 (14.0) 2.0 (14.0) 1.6 (11.0) 1.5 (10.5) 1.6 (11.0) 2.6 (18.1) 3.0 (20.9) 2.4 (16.8) 3.0 (20.9) 1.1 (7.9) 2.5 (16.9) 4.1 (28.6) 1.8 (12.2) 1.9 (12.9) 3.2 (22.1) 3.2 (22.1) 2.4 (16.5) 3.9 (26.9) 2.9 (20.0) 2.5 (17.2) 4.9 (33.8)
FM Approvals
1-252
Product Designation
10
1500 (5700) 2000 (7550) 2000 (7570) 2500 (9465) 3000 (11 355) 2250 (8515) 4500 (17 035) 6750 (25 550)
3.2 (22) 4.5 (31) 2.2 (15) 2.4 (17) 2.6 (18) 1.6 (11) 2.4 (16) 2.9 (20)
10
SS07F
10
Wilkins Operation, Zurn Industries Inc, 1747 Commerce Way, Paso Robles CA 93446
Model 310 4 300 (1135) 500 (1895) 750 (2840) 1000 (3785) 1500 (5680) 2000 (7570) 1.0 (6.9) 2.3 (16) 4.6 (32) 1.6 (11) 3.2 (22) 5.4 (37)
FM Approvals
1-253
3 4 6 8
Size 3 in. available with NPT ends rated at 400 psi (2760 kPa). Sizes 3, 4, 6, 8 in. available with 150 lb F.F. flanges rated at 250 psi (1725 kPa). Sizes 3, 4, 6, 8 in. available with 300 lb R.F. flanges rated at 400 psi (2260 kPa). Sizes 80, 100, 150, 200 mm available with ISO PN10, PN16, PN25 flanges rated at 12, 16, 25 bar (175, 232, 363 psi) respectively. All above models available with white epoxy coating on body. Add suffix -KC to model no. Available ANSI flanged body connections are as follows: Class 300 inlet, Class 150 outlet; 250 psi rated working pressure, Class 300 inlet, Class 300 outlet; 400 psi rated working pressure, Class 150 inlet, Class 150 outlet; 250 psi rated working pressure.
3 4 6 8
3 4 6 8
116-1FM
4 6 8
Sizes 4 and 6 in. NPS valves available with ANSI Class 125 and 250 rated flanges. 8 in. NPS valves available with ANSI Class 125 rated flanges only. ANSI Class 125 valves have a rated working pressure of 175 psi (1205 kPa). ANSI Class 250 valves have a rated working pressure of 300 psi (2070 kPa).
FM Approvals
1-254
Model No.
Sizes 4 and 6 in. NPS valves available with ANSI Class 125 and 250 rated flanges. 8 in. NPS valves available with ANSI Class 125 rated flanges only. ANSI Class 125 valves have a rated working pressure of 175 psi (1205 kPa). ANSI Class 250 valves have a rated working pressure of 300 psi (2070 kPa).
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Fig. No. Component Description Nominal Size, InletsOutlet, in.
A101 A102
300 psi (2070 kPa) rated working pressure.
334 334
Ban Chang Hardware Co Ltd, 17 Lane 620, Sec 3 Lu Ho Rd, Lu Kang Chang Hua, Taiwan ROC
Fig. No. Component Description Nominal Size, InletsOutlet, in.
86A 86B
2122124 2122124
These connections have a 300 psi (2070 kPa) rated working pressure.
Fig. No. Component Description Nominal Size, InletsOutlet, in.
B87 B88
2122124 2122124
Model 614. Sprinkler System Alarm Tester. 1 and 114 in. NPT female threaded inlet with male threaded outlet. 12 in. nominal orifice. 175 psi (1205 kPa) rated working pressure.
These connections have a 300 psi (2070 kPa) rated working pressure.
FM Approvals
1-255
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Fig. No. Component Description Nominal Size, InletsOutlet, in.
Model 21-132 Model 21-203 Model 21-133 Model 21-207 Model 21-201* Model 21-132** Model 21-133**
*250 psi (1725 kPa) rated working pressure.
Double Check, Straightway Siamese Double Check, Straightway Siamese Double Check, 90 Siamese Double Check, 90 Siamese Single Check, Straightway Siamese Straightway Siamese Dual Clapper 90 Siamese Dual Clapper
**These connections are FM Approved for hose threads conforming to the standard for hose coupling screw threads, ANSI B2.4 or the Engineering Division, Dept. of Purchase, City of New York, Specification No. 2103b, and outlet conforming to 8 threads per in. per ANSI B2.1. Nominal Size, InletsOutlet, in.
Fig. No.
Component Description
Powhatan Model 21-201* Powhatan Model 21-132 Powhatan Model 21-203 Powhatan Model 21-132** Powhatan Model 21-133 Powhatan Model 21-207 Powhatan Model 21-133**
*250 psi (1725 kPa) rated working pressure.
Single Check, Straightway Siamese Double Check, Straightway Siamese Double Check, Straightway Siamese Straightway Siamese Dual Clapper Double Check, 90 Siamese Double Check, 90 Siamese 90 Siamese Dual Clapper
**These connections are FM Approved for hose threads conforming to the standard for hose coupling screw threads, ANSI B2.4 or the Engineering Division, Dept. of Purchase, City of New York, Specification No. 2103b, and outlet conforming to 8 threads per in. per ANSI B2.1.
90 Sidewalk Siamese Straightway Siamese (Female Connections) Sidewalk Siamese (Male Connections) (With Sill Cock) Wall Siamese (Without Sill Cock) (With Sill Cock) Flush Siamese (Without Sill Cock)
2122124, 5, 6
2122124, 5, 6
Fire Protection Products Inc, 6241 Yarrow Dr, Suite A, Carlsbad CA 92009-1541
Fig. No. Component Description Nominal Size, InletsOutlet, in.
09-501 09-500
2122124 2122124
FM Approvals
1-256
A Giacomini SpA, Strada Per Alzo 39, 28017 S Maurizio dOpaglio, Italy
Fig. No. Component Description Nominal Size, InletsOutlet, in.
Grinnell or Gem F-715 F-716 F-717 1682 1683 1684 Straightway 45Connection 90Connection Straightway 45Connection 90Connection 2122124 2122124 2122124 2122124 334 2122124 2122124
Potter-Roemer Inc, 15125 Proctor Avenue, Box 3527, City of Industry CA 91744-0527
Fig. No. Component Description Nominal Size, InletsOutlet, in.
5710 5715
2122124 2122124
Shuenn Cherng Industrial Co Ltd, 113 Tsao-Kang Lane, Tsao-Jong Lee Lukang, Chang Hua Hsien 505, Taiwan ROC
Fig. No. Component Description Nominal Size, InletsOutlet, in.
22D 21S
2122124 2122124
Wilson & Cousins Interior Fire Protection, 4390 Paletta Court, Burlington, Ontario L7L 5R2 Canada
Fig. No. Component Description Nominal Size, InletsOutlet, in.
IE-33S
2122124
IE-34S
2122124
Zhejiang Slion Brass-Craft Manufacturing Co Ltd, 256 Chuyou South Rd Chumen, Yuhuan, Zhejiang, China 317605
Fig. No. Component Description Nominal Size, InletsOutlet, in.
8511030
2122124
8511031
2122124
These connections have a 300 psi (2070 kPa) rated working pressure.
FM Approvals
1-257
BALL DRIPS
Ball drips are designed to automatically drain off water which may leak into piping that must be kept free of water. A common use is on fire service pumper connections or the trim of dry pipe valves. The ball drip is normally open and closes when the flow of water through is between 4 and 10 gal/min (15 through 40 dm3/min). Unless otherwise noted in the listing, these ball drips have a rated working pressure of 175 psi (1205 psi).
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Model A. 12 in. NPS.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model C. 12, 34 in. NPS.
Dixon Valve & Coupling Company, 800 High Street, Chestertown MD 21620
Automatic Model 168. Automatic Model 168-200.
Globe Fire Sprinkler Corp, 4077 Air Park Dr, Standish MI 48658
Models C, E, F. Model WM. Single gong. Model WM-2. Double gong.
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Model No. PM 12 3569 93, AG2.
Reliable Automatic Sprinkler Co Inc, 1470 Smith Grove Road, Liberty SC 29657-0313
Model C.
Star Sprinkler Inc, 7071 S 13th St, Suite 103, Oak Creek WI 53154
Model CD.
Venus Fire Protection Ltd, 4105 Portland Blvd, Sherbrooke, Quebec J1L 1X9, Canada
Astra Model E.
FM Approvals
1-258
GROOVED COUPLINGS
Grooved couplings are used to join pipe and fittings in both wet and dry sprinkler systems. Unless otherwise noted, these couplings are intended to provide some flexibility in piping systems. Typical applications are in sprinkler risers, in feed mains passing through walls from one building area to another, in locations subject to earthquakes, in the discharge line from aboveground pump suction tanks, in new connections to existing feed mains and in air or water fire service lines subject to excessive vibration or difficult alignment. Unless otherwise noted, these couplings are limited to use with rolled or cut groove-ended pipe, valves and fittings, at a minimum rated working pressure of 175 psi (1205 kPa) and are suitable for aboveground service. Higher rated pressures are noted in the text of the listing. Selection of pipe schedules for use with grooved pipe couplings should be made according to applicable FM Global Property Loss Prevention Data Sheets installation standards. These pipe schedules determine system pressure ratings and may take precedence over the higher rated working pressures listed for some couplings. Installation must be made according to the manufacturers instructions and requirements. Where couplings are used to join FM Approved pipe, the pipe manufacturers installation instructions and requirements must also be observed. Grooves should be made according to ANSI/AWWA C606 (latest edition), Grooved and Shouldered Joints, unless otherwise specified. FM Approved grooved pipe couplings joining steel pipe may be used in underground service, subject to the installation restrictions placed upon the pipe and to the coupling manufacturers recommendations and requirements. Unless otherwise stated in the listing, these couplings have been evaluated for a maximum ambient temperature of 225F (107C), suitable for use in normal warehouse protection. For special applications, temperatures, or environments, the manufacturers recommendations and requirements are to be followed.
a, b, c a, b, c
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. c. Approved when supplied with EPDM gasket.
10
114-3 4 5-8
a, b, c a, b, c a, b, c a, b, c
11
114-8
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
FM Approvals
1-259
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Gruvlok 7000
114-3 114, 112, 2 114-4 1-2 114, 112, 2, 212, 3, 4 114-8 114-8 212-8 76, 108, 133, 139.7, 159, 165 mm
c, d, w c, m, w c, e, f, n, r, s, t, u, v, w c, p, w c, n, w a, c, w b, c, k, m, w c, k, w c, h
300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
114-8 1-12
Cut Groove, Rolled Groove Cut Groove Rolled Groove Rolled Groove Rolled Groove 2,
a, b, c, f a, c, w
175 (1205) 500 (3445) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 400 (2760) 450 (3105) 350 (2415) 500 (3445) 500 (3445) 400 (2760) 175 (1205) 300 (2070) 300 (2070) 175 (1205)
c, m, w c, d, w c, n, w c, k, w
212, 3, 4 3-8
1-6 8 10 12 76.1 mm 165.1 mm 216 mm, 267 mm 318 mm 7001E 7000E 114, 10, 12 112, 2, 212, 3, 4, 5
Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
b, c, w b, c, w b, c, w b, c, w c, h c, l c, l a, b, c, w a, b, c, d, i, k, t, w c, h a, b, c, w
76, 165 mm 6, 8
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket Grade E (green stripe), Grade E Type A (violet stripe), and Grade E Type A Dri-Seal (violet stripe). Flush gap gasket in 112-12 in. nominal sizes are interchangeable with standard gasket. d. Min schedule pipe to be joined: 3 in. or smaller Allied Tube & Conduit FM Approved XL, Super-XL and Super-40 Thinwall pipe. e. Min schedule pipe to be joined: Allied Tube Dyna-Flow Lightwall pipe, 114-4 in. 300 psi (2070 kPa). f. Min schedule pipe to be joined: Allied Tube & Conduit Super-Flo Lightwall pipe, 114-4 in. 300 psi (2070 kPa). h. Metric Pipe: Equivalent to 76.1, 108, 133, 139.7, 159 and 165.1 mm. British Standard 1387, medium or equal. j. Central Sprinkler TL threadable Thinwall pipe. k. Tex-Tube Co. Tex-Flow non-threadable Lightwall pipe. l. JIS Schedule 20 pipe or heavier. m. For use with Northwest EZ-Flow in 3 through 6 in. sizes. n. Youngstown Tube Fire-Flo Non-Threadable Lightwall Sprinkler Pipe. p. IDOD Systems Gal-5 and All-Gal, Bull Moose Ultra-Eddy, and Wheatland WST Schedule 5 Pipes. r. IDOD Systems Gal-7 and Gal-flo pipe. s. Western International Fire Line Flow or Fire Line Thread Light pipe. t. Wheatland Mega-Flow, Mega-thread, MLT, GL, and WLS pipe. u. Bull Moose EDDY-flow, EDDY-lite pipe. v. For use with Yieh Phui SPS Flow Pipe in 114 through 4 in. NPS. w. EPDM Grade E (green stripe) flush gap gaskets in 1-12 in. nominal sizes are interchangeable with standard EPDM gaskets.
FM Approvals
1-260
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
C-1
C-3
Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, d, e, f, g, h, i, k, l, m, n, p, q, s c, r a, b, c, s a, b, c, o, s a, b, c a, b, c, d, e, f, g, h, i, k, l, m, n, p, q, s c, r a, b, c, s
300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070)
Remarks: a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S, 8 in. NPS and larger, 0.188 in. (5 mm) wall. c. With EPDM gasket using standard gasket lubricant or dry lubricant. d. For use with Allied Tube and Conduit Super-Flo and Dyna-Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. e. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in size 4 in. NPS. f. For use with Allied Tube and Conduit XL, XL-II threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. g. For use with Allied Tube and Conduit Super-XL threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. h. For use with Allied Tube and Conduit Super-40 threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. i. For use with Allied Tube and Conduit BLT threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. k. For use with Wheatland Tube WLS threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. l. For use with Western International Forest Products Fire-Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 3, and 4 in. NPS. m. Available with flush gap gasket, 112-12 in. NPS. n. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3 and 4 in. NPS. o. For use with Bull Moose Ultra-Eddy Schedule 5 steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. p. For use with Wheatland Tube Mega-Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 3, and 4 in. NPS. q. For use with Welded TubeBerkeley LLC Steady-Flow Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. r. For use with BS 1387 Medium or Heavy steel pipe in sizes: 76 and 165 mm NPS. s. EPDM Grade E (green stripe) flush gap gaskets in 1-12 in. nominal sizes are interchangeable with standard EPDM gaskets.
Beijing Tian Ning Yi He Pipe System Equipment Co Ltd, No. 2, North Road, Ju Yuan, Ma Pa Ju Yuan Industrial Base, Shunyi District, Beijing, P. R. China
Product Designation Pipe Size, mm Pipe Ends Remarks Max Working Pressure, psi (kPa)
GCQT2 GCQT2
a, b, c a, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
10
114-4 5-8
a, b, c, d a, b, c a, b, c
11
a. b. c. d.
114-8
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket. For use with IDOD Systems Gal-5 pipe at 175 psi (1205 kPa).
Dong Yang Bend Co Ltd, 37-3, Songma-Ri, Daegot-Myeon, Gimpo-Si, Gyeonggi-do, Korea
Product Designation Pipe Actual Size mm/in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c a, b, c
FM Approvals
1-261
Product Designation
Pipe Ends
Remarks
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien, Taiwan ROC
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
a, c b, c a, b, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. 0.188 in. (5 mm) wall. c. With EPDM, EM757A or SBR gaskets.
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang, Tsun Ta Liau Shiang Kaohsiung Hsien, Taiwan ROC
DUCCO Brand Couplings
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
GT-402
114, 112, 2, 76, 133, 165 mm 212, 3, 4, 5, 6 8 114, 112 2, 212, 3, 4, 5, 6 76, 133, 165 mm 8
Cut Groove
a, c, d
500 (3445) 175 (1205) 500 (3445) 300 (2070) 175 (1205) 500 (3445) 400 (2760) 300 (2070)
Rolled Groove
a, c b, c b, c
b, c a, b, c a, b, c a, b, c
GT-402H
2, 212, 3 4 6, 8
a. b. c. d.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For British Standard 1387, medium steel pipe or equal.
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Inter-Fit 10
a, b, c a, b, c a, b, c a, b, c, d, e, k, m c, i
500 (3445) 300 (2070) 175 (1205) 300 (2070) 300 (2070)
FM Approvals
1-262
Product Designation
Pipe Ends
Remarks
Inter-Fit 11
a, b, c a, b, c c, i c, e, h, j, k, o, p, r, t
500 (3445) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070)
Inter-Fit 12
c, n c, e, h, j, k, m a, b, c, s c, i
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket and flush-seal gasket. d. For use with Northwest EZ-Flow e. Allied Dyna-Flow h. Bull Moose EDDY-Lite i. British Standard BS 1387 Pipe, Med. and Heavy. j. Allied XL k. Allied Super-Flo m. Central Sprinkler TL pipe. n. Wheatland Schedule 5 and IDOD Gal-5. o. IDOD Gal-7. p. Tex-Tube Tex-Flow r. Western International Fire-Thread and Fire-Flow s. Northwest EZ-Flow t. Welded Tube Berkeley, LLC Steady-Flow
JFE Pipe Fitting Mfg Co Ltd, 153 Tajime-Cho, Kishiwada Osaka, Japan
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Working Pressure, psi (kPa)
7705
1-8
a, b, c, d, e, f, g, h, j, k, l, m, p
300 (2070)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10. c. Allied Super-Flo, Allied Dyna-Flow, 4 in. or smaller. d. Allied Super 40, Bull Moose Ultra-Eddy, 3 in. or smaller. e. Bull Moose EDDY-LITE, 114 through 2 in. f. BS 1387 medium or heavy grade, 114, 112, 2, 212, 3, 4, 6 in. g. Bull Moose Tube EDDY-FLOW pipe, 112-4 in. h. American Tube BLT, 114 through 2 in. j. American Tube Dyna-Thread 114 through 2 in. k. Super-XL, 114 through 3 in. l. Allied Tube XL-II, 114 through 3 in. m. Central TL, 114 through 2 in. p. Wheatland WST, 114 through 2 in.
Jinan Meide Casting Co Ltd, No. 3 Nanmen Road, Pingyin, Jinan, 250400 China
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
1N 1N
Remarks: a. b. c. d.
a, b, c, d c, d
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. Approved when supplied with EPDM gasket. Approved for use with GB/T3092 regular and extra heavy pipe, ISO 4200, and BS 1387 medium and heavy pipe.
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Quikhinge 007
a, b, c, f, j a, b, c, h, j
FM Approvals
1-263
Product Designation
Pipe Ends
Remarks
07
Rolled Groove Cut Groove Cut Groove Rolled Groove Cut Groove, Rolled Groove Rolled Groove
c, d, f, j a, b, c, f, j b, c, j a, c, j c, g, h, j a, b, c, d, f, j c, g, j
75
300 (2070) 500 (3445) 400 (2760) 500 (3445) 500 (3445) 500 (3445) 290 (2000) 175 (1205)
76
a. b. c. d. e. f. g. h. j.
10-12
a, b, c, f, j
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket (green stripe), -30 to +230F; with nitrile gasket (orange stripe), -20 to +180F. For use with Allied Tube & Conduit Dyna-Flow Lightwall pipe at 175 psi (1205 kPa). For use with all FM Approved Thinwall sprinkler pipe. With EPDM EA gasket (violet stripe). For use with BS 1387 metric pipe in sizes 76.1, 108, 133, 159, and 165 mm NPS. For use with DIN 2448 and 2458 metric pipe. With EPDM gasket EP, using pre-lubricated material.
Couplings
Cut Groove, Rolled Groove Rolled Groove, Cut Groove Cut Groove Rolled Groove Rolled Groove
a, b, c, j b, c a, c a, b, c c, f c, e, g, d, h c
1-3 112-3
300 (2070) 175 (1205) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. c. With EPDM gasket. d. When joining Allied Tube & Conduit XL threadable Thinwall pipe. e. FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. f. For Schedule 5 /non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. g. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use with Central Sprinkler TL threadable Thinwall pipe, Allied BLT and Wheatland WLS. j. For use with Bull Moose Tube EDDY-Flow pipe.
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Style 10
a, b, c a, b, c a, b, c, p c, l a, b, c, d, m c, g, o a, b, c c, k c, p
500 (3445) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205) 300 (2070)
FM Approvals
1-264
Product Designation
Pipe Ends
Remarks
2 Style 11 114-3 114-4 114-2 114-4 114-8 Style 12 114-3 114-4 114-2 114-8 114-2 3
c, q c, l c, d, m c, g a, b, c a, b, c c, l c, d, m c, g, o a, b, c c, q, r c, r
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With standard EPDM gasket, or dry lubricant EPDM gasket. d. Allied Dyna-Flow. g. Bull Moose EDDY-Lite. k. British Standard BS 1387 Pipe. l. Allied XL. m. Allied Super-Flo. o. With Central Sprinkler TL threadable Thinwall pipe. p. Tex-Tube Co. Tex-Flow non-threadable Lightwall pipe. q. Western International Forest Products Fire Thread threadable Thinwall pipe. r. Western International Forest Products Fire Flow non-threadable Lightwall pipe.
Qingdao V-Cart Piping Systems Co Ltd, JuiZhao Road, NanGuan Industry Zone, JiaoZhou City, Qingdao, China
Model No. Sizes, in. or mm End Connections Notes Pressure, bar (psi)
114-2, 57, 76 mm Figure 10 3, 4 5 through 12 108, 127, 133, 139, 159, 165 mm
a. b. c. d.
Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, d a, b, c a, b, c, d
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with GB/T 3091-93 or GB/T 8163-99 Pipe.
Robor Pipe Systems, Box 1098, Isando, Gauteng 1600, South Africa
Style STEELGRO F75 Grooved.
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Pipe Couplings
Rolled Groove Cut Groove Rolled Groove Rolled Groove Cut Groove
a, b, c, j b, c a, c a, c c, f c, d, e, g, h c c, k
300 (2070) 175 (1205) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 300 (2070)
a. b. c. d. e.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. When joining Allied Tube & Conduit XL threadable Thinwall pipe. FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe.
FM Approvals
1-265
f. g. h. j. k.
For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. For use with Central Sprinkler TL threadable Thinwall pipe, Allied BLT, and Wheatland WLS. For use with Bull Moose Tube EDDY-Flow pipe. For use with BS 1387 medium and heavy pipe, or equal.
SCE Company Ltd, Unit E&F, 20/F., CDW Building, 388 Castl Peak Road, Tsuen Wan, N.T., Hong Kong
Product Designation Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Remarks
2,
212,
3, 4, 5, 6
76.1, 165 mm
a, b, c a, b, c
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. c. Approved when supplied with EPDM gasket.
SPT Metal Corp, 19-1 Da Y/eh St, Da Liao Hsiang, Kaohsiung Hsien, Taiwan ROC
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
505 505 505 505 505 507 507 507 507 505 Stainless Steel 505 Stainless Steel
1-4 1, 114, 112, 2, 212, 3, 4, 5, 6, 8 76.1, 165.1 mm 114 through 4 114 through 4 112-6 112 through 4 112 through 14 16 through 24 2, 212, 3, 4, 5, 6, 8, 10 12
Rolled Groove Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
c, e, f, g, h, i, j, n a, b, c, n c, d, n c, m, n c, n c, e, f, g, h, i, j, n c, n a, b, c, n a, b, c, n c, k, p c, k, p
300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 250 (1720)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For metric pipe per BS 1387 medium or equal. e. When joining Allied Tube & Conduit XL threadable Thinwall pipe, 1-2 in. only. f. For use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. g. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. i. For use with Central Sprinkler TL threadable Thinwall pipe. j. For use with Bull Moose Tube EDDY-Flow pipe. k. For use on Schedule 40 Cut Groove and Rolled Groove only. m. For use with Wheatland Mega-Flow non-threadable Thinwall pipe. n. Ductile Iron p. Stainless Steel.
Shanghai Recomb Piping System Co Ltd, No. 270 Yixian Rd, Shanghai 200434, Peoples Republic China
Product Designation Pipe Actual Size mm Pipe Ends Remarks Max Working Pressure, psi (kPa)
XGQT2
33.7, 42, 48, 60, 73, 76, 89, 108, 114, 133, 140, 141.3, 159, 165, 168 and 219 273 and 325 42.4 48.3 60.3
a, b, c
300 (2070)
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c a, b, c a, b, c
FM Approvals
1-266
Product Designation
Pipe Ends
Remarks
XGQT2-76.1 XGQT2-88.9
76.1 88.9
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205)
a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Shanghai Vision Mechanical Joint Co Ltd, Jinlan Road, Loutang Industrial Park, Jiading District, Shanghai 201807 PRC
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
101 101
a. b. c. d.
114, 112, 2, 212, 3, 4, 6, 8 57, 76, 108, 133, 140, 159, 165 mm
a, b, c, d, e a, b, c, d, e
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. With EPDM gasket. For use with Chinese Standard GB/T 3091-1993, GB/T 3092-1993 welded steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30). e. For use with Chinese Standard GB/T 17395-1998 seamless steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30).
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Working Pressure, psi (kPa)
7705
1 through 8
Rolled Groove, Cut Groove Rolled Groove Rolled Groove, Cut Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove, Cut Groove
7705 7705H 7705 7705 7707 7707 7707 7707 7707 7707
1-2 8 10, 12 10, 12 2 through 10 12 112 through 10 212, 5, 6 14, 16, 18, 20, 22 24
a, b, c, d, e, f, g, h, j, l, m, q, r, s p, s, t a, s b, s a, s b, s a, b, s a, s s, f a, s a, s
300 (2070) 175 (1205) 450 (3100) 175 (1205) 250 (1720) 450 (3098) 300 (2066) 500 (3443) 500 (3443) 175 (1205) 250 (1720)
a. b. c. d. e. f. g.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 and 10 in.-0.188 in. wall; 12 in.-0.250 in. wall. Allied Super-Flo, Allied Dyna-Flow, 4 in. or smaller. Allied Super 40 and Super-XL, 1 through 3 in. Bull Moose EDDY-Lite, 1 through 2 in. BS 1387 medium or heavy grade, 114, 112, 2, 212, 3, 4, 6 in. Bull Moose Tube EDDY-Flow pipe, 112 through 4 in.
FM Approvals
1-267
h. American Tube BLT, 1 through 2 in. j. American Tube Dyna-Thread 1 through 2 in. l. Allied Tube XL-II, 1 through 3 in. m. Central TL, 1 through 2 in. p. Wheatland WST, 1 through 2 in. q. Fire-Thread, 1 through 2 in. r. Fire-Flow, 112 and 112 in. s. EPDM gasket. t. Bull Moose Ultra-EDDY, 2 in. or smaller.
Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove
a, b, c, d a, b, c, f a, b, c, f
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket (green Stripe). For use with Korean KS D3507 pipe. For use with metric OD pipe.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Grinnell 7000S
Rolled Groove, Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove
a, b, c b, c a, c c, h c, h c, d, e, f, j a, c c, k b, c b, c b, c a, c c, l c, l a, b, c, d, e, h, j, l, m, q, s, u p, s, t
Grinnell 7001
1 1
500 (3445) 350 (2415) 500 (3445) 500 (3445) 400 (2760) 300 (2070) 500 (3445) 300 (2070) 400 (2760) 450 (3105) 350 (2415) 500 (3445) 500 (3445) 400 (2760) 300 (2070) 175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 and 10 in. 0.188 in. wall; 12 in. 0.250 in. wall. c. Allied Super-Flo, Allied Dyna-Flow, 4 in. or smaller. d. Allied Super 40 and Super-XL, 1 through 3 in. e. Bull Moose EDDY-Lite, 1 through 2 in. h. American Tube BLT, 1 through 2 in. j. American Tube Dyna-Thread 1 through 2 in. l. Allied Tube XL-II, 1 through 3 in. m. Central TL, 1 through 2 in. p. Wheatland WST, 1 through 2 in. q. Fire-Thread, 1 through 2 in. s. EPDM gasket. t. Bull Moose Ultra-EDDY, 2 in. or smaller. u. For use with Yieh Phui SPS Flow Pipe in 114 through 4 in. NPS. Product Designation Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Remarks
540
212
a, b, c, h, i, j, k, s
300 (2070)
FM Approvals
1-268
Product Designation
Pipe Ends
Remarks
575
Cut Groove, Rolled Groove Rolled Groove Rolled Groove Rolled Groove Rolled Groove Rolled Groove Rolled Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove, Cut Groove Rolled Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove, Cut Groove Rolled Groove Cut Groove
a, b, c c, f, i, j, s, t, w c, d, f, n, p, u c, f, g c, f, h, l, q, v c, o c, o c, f, o a, b, c, f c, f, h, l, n, o, q, u, v, y c, f, i, j, w, x c, f c, o a, b, c, f c, f, p, u c, k, x
705
300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205) 250 (1725) 175 (1205) 300 (2070) 300 (2070) 500 (3445) 450 (3105) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 200 (1380) 300 (2070)
705 BS 707
76, 139, 165 mm 112-12 112-12 112-2 112-2 112-4 3-4 6 14 76.1 mm 165.1 mm
c, f, k a, c, f b, c, f c, f, n, u c, f, i, j, s, t, x c, f, h, q c, o c, o a, b, c c, f, k
a. b. c. d. f. g. h. i. j. k. n. o. p. q. s. t. u. v. w. x. y.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket using standard gasket lubricant or dry lubricant. For use with Allied Tube & Conduit Dyna-Light Schedule 5 non-threadable Lightwall pipe. Also available with Tri-Seal EPDM gasket. Recommended by the manufacturer for dry systems. For use with standard gasket lubricant or dry lubricant. For use with Allied Tube & Conduit XL threadable Thinwall pipe. For use with Allied Tube & Conduit Dyna-Flow and Super-Flo non-threadable Lightwall pipe. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. For use with BS1387 medium or heavy pipe. For use with Bullmoose Tube Co. Ultra-EDDY Schedule 5 non-threadable Lightwall pipe. For use with Northwest EZ-Flow non-threadable Lightwall pipe. For use with IDOD Systems Schedule 5 non-threadable Lightwall pipe. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. For use with Allied XL pipe. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. For use with Youngstown Tube Co. Fire-Flo non-threadable Lightwall steel sprinkler pipe. For use with Youngstown Tube Co. EZ-Thread threadable Thinwall steel sprinkler pipe. For use with IDODs Gal-7 and Gal-Flo pipe. For use with Bullmoose Tube Co. EDDY-flow non-threadable Lightwall pipe.
Remarks
75
114, 112, 2
Rolled Groove
a, e, x, aa
175 (1205)
FM Approvals
1-269
Product Designation
Pipe Ends
Remarks
114, 112, 2 112, 2 114, 112, 2, 212, 3, 4 114, 2, 3, 4, 6 112, 2, 212, 3 112, 212,
e, h, aa t, aa a, e, g, j, k, u, w, z, aa, ab o, q, s, v, y, aa a, e, p, aa a, e, l, aa a, e, aa e, s, aa a, e, z, aa e, s, aa a, e, i, v, y, aa a, c, e, aa b, d, e a, d, e, aa a, d, e, aa b, e, n, aa b, d, e a, e, i, f a, e, o, q, s, zz
112, 2, 212, 3 112, 2, 212, 3, 4 6 6 3, 4 3, 4, 6, 8 1-8 3.0 112, 2, 212, 3, 4, 5, 6, 8 5, 6, 8 108, 133, 139.7 152, 159, 165 mm 76 mm 216 mm 1, 1
1 4,
1 2, 2 3, 4, 6
1 2,
300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 500 (3445) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 450 (3105) 175 (1205) 300 (2070) 300 (2070) 450 (3105) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205)
a, e, p
a, e, l
77
a, c, e, aa a, c, e o, aa e, h, aa a, e, g, w, z, aa a, e, j, k, u, aa q, y, aa e, s, aa e, s, aa a, e, z, aa a, d, e, aa a, e, aa a, d, e a, e, i, v, aa b, e, n, aa a, e, p, aa a, e, l, t, y, aa a, b, n, aa a, e, r, aa e, ff
1,
114,
112,
FM Approvals
1-270
Product Designation
Pipe Ends
Remarks
307
3, 4, 6, 8, 10, 12
i, m
175 (1205) 500 (3445) 300 (2070) 350 (2415) 350 (2415) 300 (2070) 250 (1725)
705
c, d
791 Boltless
q, aa a, c, e, aa a, d, e, aa a, d, e, aa a, d, e, aa
a. Also available with Style 77FS gasket. Recommended by manufacturer for use with dry pipe systems. aa. For use with VicMax EPDM Gaskets in 2 through 8 in. and 76 and 165 mm sizes. ab. For use with Yieh Phui SPS Flow Pipe in 114 through 4 in. NPS. b. For steel pipe having metric sized outside dia. (ref. DIN 2448 & 2458). c. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. d. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. e. With gasket E (green stripe), H (white stripe) or L (solid red). f. For use with JIS steel pipe. ff. For use with JIS G3452 steel sprinkler pipe. g. For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. h. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. i. With gasket M. j. For use with Welded Tube Berkeley Steady Flow Lightwall non-threadable, Lightwall steel sprinkler pipe in sizes 114, 112, 2, 212, 3 and 4 in. NPS. k. For use with Welded Tube Berkeley Steady Thread threadable Thinwall steel sprinkler pipe in sizes 1, 114, 112 and 2 in. NPS. l. When joining Allied Tube & Conduit XL threadable Thinwall pipe. m. Joins rolled or cut groove steel pipe, per note d to cut groove iron pipe per note i. n. For steel pipe having outside dia. sized per British Standard 1387, medium or equal. o. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. p. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. q. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. s. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 and 6 in. nominal size. t. For use with Central Sprinkler TL threadable Thinwall pipe. u. For use with Bull Moose Tube EDDY-Flow pipe. v. For use with Tex-Tube Co. Tex-Flow non-threadable Lightwall pipe. w. For use with Central 7 pipe. x. For use with IDOD Systems Gal-5 pipe. y. For use with Western Fire-Flow and Fire-Thread pipe. z. For use with Wheatland Mega-Flow pipe. zz. For use with Wheatland MLT up to 2 in. nominal size.
Victaulic Company of Japan Limited (The), IINO Building 3F, 1-1, Uchisaiwaicho 2-Chome, Chiyoda-Ku, Tokyo 100-0011, Japan
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Jady 35 G-1
a. b. c. d.
a, b, c a, d
With EPDM gasket, orange stripe. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 312 in. or smaller Schedule 10S; 4 in. or larger 0.188 in. (5 mm) wall. For use with JIS G3454, Schedule 40 steel sprinkler pipe.
75
1, 114, 112, 2 1, 114, 112, 12, 3, 4, 6 2, 2 1, 114, 112, 2, 212, 3 1, 114, 112, 2, 212, 3 1-8 3.0 1-4 5-8
a, e, t, v a, e, o, q, s, w a, e, p a, e, l a, c, e a, b, d, e a, d, e a, d, e
300 (2070) 300 (2070) 175 (1205) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 300 (2070)
FM Approvals
1-271
Product Designation
Pipe Ends
Remarks
77
108, 133, 139.7 152, 159, 165 mm 3.0 1-12 14 1, 114, 112, 2 1-4 212, 3, 4, 6 1-12 14 1-12 165 mm
34-2
Cut Groove Rolled Groove Rolled Groove, Cut Groove Rolled Groove Cut Groove, Rolled Groove
b, e, n b, d, e a, c, e a, c, e o q, u o, s a, d, e a, d, e a, c, e b, e, n a, e, p a, e a, e, l, t a, b, n i, m c, d q a, c, e a, d, e a, d, e a, d, e
112-3 1-2 108, 133, 139.7, 159 mm 3-12 114, 112 (42, 48 mm) 2-4 2, 3, 4, 6, 8 12, 3, 4 2, 2 6 8 212,
300 (2070) 175 (1205) 500 (3445) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 450 (3105) 300 (2070) 500 (3445) 450 (3105) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 175 (1205) 500 (3445) 300 (2070) 350 (2415) 350 (2415) 300 (2070) 250 (1725)
a. Also available with Style 77FS gasket. Recommended by manufacturer for use with dry pipe systems. b. For steel pipe having metric sized outside dia. (ref. DIN 2448 & 2458). c. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. d. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. e. With gasket E (green stripe), H (white stripe) or L (solid red). i. With gasket M. l. When joining Allied Tube & Conduit XL threadable Thinwall pipe. m. Joins rolled or cut groove steel pipe, per note d to cut groove iron pipe per note i. n. For steel pipe having outside dia. sized per British Standard 1387, medium or equal. o. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. p. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. q. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. s. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 and 6 in. nominal size. t. For use with Central Sprinkler TL threadable Thinwall pipe. u. For use with Bull Moose Tube EDDY-Flow pipe. v. For use with Wheatland Mega-Flow up to 4 in. nominal size. w. For use with Wheatland MLT up to 2 in. nominal size.
a, b, c, e, f, h, j c, d a, b, c, e, f, h, j
through 6
c, d
300 (2070) 300 (2070) 500 (3445) 300 (2070) 300 (2070)
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For metric pipe per BS 1387 medium or heavy.
FM Approvals
1-272
e. f. h. j.
For use on Wheatland Mega-Flow pipe. All FM Approved for use on Allied Tube & Conduit Dyna-Flow and Super-Flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size at 250 psi (1725 kPa). For use with Bull Moose Tube EDDY-Flow pipe.
Weifang 100tong Casting Co Ltd, No. 1919 Jinchang South Road, Weicheng District, Weifang, Shandong, PR China 261052
Product Designation Nominal Pipe Size, mm Pipe Ends Rated Working Pressure, psi (kPa)
Remarks
GCQT2
33, 42, 48, 60, 76, 89, 108, 114, 133, 140, 159, 165, 168, 219
a, b, c, d, e, f
230 (1600)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with BS 1387 medium or equal metric pipe. e. For use with Chinese Standard GB/T 3091-1993, GB/T 3092-1993 welded steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30). f. For use with Chinese Standard GB/T 17395-1998 seamless steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30).
AJ510 AJ510
Remarks: a. b. c. d.
a, b, c, d, e c, d, e
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. With EPDM gasket. For use with Chinese Standard GB/T 3091-1993, GB/T 3092-1993 welded steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30). e. For use with Chinese Standard GB/T 17395-1998 seamless steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30).
ATUSA empresarial SL, Aptd. Correos 8, Poligono Industrial Agurain S/N, 01200 Salvatierra, lava, Spain
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
a, b, c a, b, c
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. c. Approved when supplied with EPDM gasket.
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Working Pressure, psi (kPa)
Cut Groove, Rolled Groove Rolled Groove Rolled Groove, Cut Groove Rolled Groove
a, c c, d b, c, w a, b, c, d, e, f, j, l, p, r, s, t, w c, n, w c, n, w
Rigidlite 7400*
1-8 212-4 6
750 (5170) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205)
FM Approvals
1-273
Product Designation
Fitting Description
Remarks
3-8 76.1, 139.7, 165.1 mm 1-2 Gruvlok 7400 S* Rigidlok 7401* 2-6 112-3 112-4 112-2 112-3 112-3 3-8 4, 5 6 8, 10, 12 112-4 5, 6 8 10 12 76.1, 139.7, 165.1 mm
Rolled Groove Rolled Groove, Cut Groove Rolled Groove Rolled Groove Cut Groove, Rolled Groove
c, n c, h c, m a, b, c, d, e, f, h, l, m c, e c, f, p c, o, w c, d, w b, c, w c, n, w b, c, w b, c, w b, c, w a, c a, c a, c a, c, w a, c, w c, h
175 (1205) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 400 (2760) 300 (2070) 750 (5170) 500 (3445) 450 (3105) 300 (2070) 300 (2070) 500 (3445)
7400E*
Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove
a, b, c, d, e, f, i, l, m, o, p, t, w a, c, w c, h c, m, w
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in areas subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket Grade E (green stripe), Grade E Type A (violet stripe), and Grade E Type A DriSeal (violet stripe). Flush gap gasket in 112-12 in. nominal sizes are interchangeable with standard gasket. d. Min schedule pipe to be joined: 3 in. or smaller Allied Tube & Conduit FM Approved XL, Super-XL and Super-40 Thinwall pipe. e. Min schedule pipe to be joined: Allied Tube & Conduit Dyna-Flow Lightwall pipe, 1-4 in. f. Min schedule pipe to be joined: Allied Tube & Conduit Super-Flo Lightwall pipe, 1-4 in. h. Metric Pipe: Equivalent to 76.1, 108, 133, 139.7, 159 and 165.1 mm. British Standard 1387, medium or equal. j. For use with Central Sprinkler TL threadable Thinwall pipe. l. Min schedule rolled groove pipe to be joined: Bull Moose EDDY-Lite, 2 in. and EDDY-flow, 112-4 in.175 psi (1205 kPa). m. Min schedule rolled groove pipe to be joined: Bull Moose Ultra-EDDY, 1-2 in., IDOD Systems Gal-5 and All-Gal, and Wheatland WST Schedule 5 pipes. n. For use with Tex-Tube Tex-Flow Lightwall pipe 212 to 6 in. o. For use with Youngstown Tube EZ-Thread Threadable Thinwall Sprinkler Pipe. p. For Use with Northwest EZ-Flow pipe in 3 thru 6 in. sizes. r. IDOD Systems Gal-7 and Gal-flo pipe. s. Western International Fire Line Flow or Fire Line Thread Light. t. Wheatland Mega-Flow, Mega-thread, MLT, GL, and WLS pipe. w. EPDM Grade E (green stripe) flush gap gaskets in 1-12 in. nominal sizes are interchangeable with standard EPDM gaskets.
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max. Working Pressure, psi (kPa)
C-4
Cut Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove
a, b, c, d, e, f, g, i, j, l, m, o, s c, p c, k, n, o, s
Remarks: a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S, 8 in. NPS and larger, 0.188 in. (5 mm) wall.
FM Approvals
1-274
c. With EPDM gasket using standard gasket lubricant or dry lubricant. d. For use with Allied Tube and Conduit Super-Flo and Dyna-Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. e. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in size 3, 4 and 6 in. NPS. f. For use with Allied Tube and Conduit XL, XL-II threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. g. For use with Allied Tube and Conduit BLT threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. i. For use with Wheatland Tube WLS threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. j. For use with Bull Moose Tube EDDY-Lite threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. k. For use with Bull Moose Tube EDDY-Flow Lightwall steel sprinkler pipe in sizes: 112 through 4 in. NPS. l. Available with flush gap gasket, 112-12 in. NPS. m. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3 and 4 in. NPS. n. For use with Bull Moose Ultra-Eddy Schedule 5 steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. o. For use with Welded TubeBerkeley LLC Steady-Flow Lightwall steel sprinkler pipe in sizes: 112 and 2 in. NPS, FM Approved for 300 psi rated working pressure, and 4 in. NPS, FM Approved for 175 psi rated working pressure. p. For use with BS 1387 Medium or Heavy steel pipe in sizes: 76 and 165 mm NPS. q. For use with Schedule 40 steel sprinkler pipe only. s. EPDM Grade E (green stripe) flush gap gaskets in 1-12 in. nominal sizes are interchangeable with standard EPDM gaskets.
Beijing Tian Ning Yi He Pipe System Equipment Co Ltd, No. 2, North Road, Ju Yuan, Ma Pa Ju Yuan Industrial Base, Shunyi District, Beijing, P. R. China
Product Designation Pipe Size, mm Pipe Ends Remarks Max Working Pressure, psi (kPa)
GCQT1 GCQT1
a, b, c a, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Style 5
a, c b, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Dong Yang Bend Co Ltd, 37-3, Songma-Ri, Daegot-Myeon, Gimpo-Si, Gyeonggi-do, Korea
Product Designation Pipe Actual Size mm/in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller - Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang Tsun Ta Liau Shiang Kaohsiung Hsien, Taiwan ROC
DUCCO Brand Couplings
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
GT-402R*
Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, e c, d a, b, c, e
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake.
FM Approvals
1-275
a. b. c. d. e.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10. With EPDM gasket. For use with Schedule 5 pipe. For use with Allied Super-Flo or Dyna-Flow pipe.
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Max Working Pressure, psi (kPa)
Remarks
Style 5*
a, b, c, s c, n c, d, g, l, m, o, p, t a, b, c c, u
300 (2070) 300 (2070) 300 (2070) 175 (1205) 175 (1205)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket, and flush-seal gasket. d. Allied Dyna-Flow g. Bull Moose EDDY-Lite l. Allied XL m. Allied Super-Flo n. BS 1387 pipe, Med. or Heavy. o. IDOD Gal-7 p. Tex-Tube Tex-flow r. Western International Fire-Thread and Fire-Flow s. Northwest EZ-Flow t. Welded Tube Berkeley, LLC Steady-Flow u. Wheatland Sch. 5 and IDOD Gal-5
JFE Pipe Fitting Mfg Co Ltd, 153 Tajime-Cho, Kishiwada Osaka, Japan
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
K-9
114 through 6 8
Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove
a, b, c, d, e, f, g, h, j, k, l, m, p a, b
7771
2 through 8 10
a, b a, b
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10. c. Allied Super-Flo, Allied Dyna-Flow, 4 in. or smaller. d. Allied Super 40, Bull Moose Ultra-Eddy, 3 in. or smaller. e. Bull Moose EDDY-LITE, 114 through 2 in. f. BS 1387 medium or heavy grade, 114, 112, 2, 212, 3, 4, 6 in. g. Bull Moose Tube EDDY-FLOW pipe, 112-4 in. h. American Tube BLT, 114 through 2 in. j. American Tube Dyna-Thread 114 through 2 in. k. Super-XL, 114 through 3 in. l. Allied Tube XL-II, 114 through 3 in. m. Central TL, 114 through 2 in. p. Wheatland WST, 114 through 2 in.
Jinan Meide Casting Co Ltd, No. 3 Nanmen Road, Pingyin, Jinan, 250400 China
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
1G
1GS
2,
212,
3, 4, 6, 8
Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, d a, c c, d a, b, c, d c, d
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30.
FM Approvals
1-276
b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. c. Approved when supplied with EPDM gasket. d. Approved for use with GB/T3092 regular and extra heavy pipe, ISO 4200, and BS 1387 medium and heavy pipe.
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
007* 1, 114,
76 mm 112, 2, 2, 212, 3, 4, 6
1 1 2,
212,
3, 4
Cut Groove, Rolled Groove Cut Groove, Rolled Groove Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Cut Groove, Rolled Groove Rolled Groove
c, d, f, g, h a, b, c, f, g, h d, e, f, g, h a, b, c, d, f, g, h a, b, c, d, h a, b, c, d, h a, b, c, d, h a, b, c, d, h a, b, c, f, g, h a, b, c, f, h a, b, c, f, h
140, 165 mm 007RT 112, 2, 3, 4, 6 76, 140, 165 mm 75RT 1 1 2, 2, 3, 4, 6, 8 76, 140 76R 79* *
Remarks:
175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 500 (3445) 300 (2070)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in areas subject to earthquake. a. b. c. d. e. f. g. h. Minimum schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 Wall (5 mm Wall). With EPDM EP gasket (green stripe). For use with DIN 2448 and 2458 steel pipe. For use with all FM Approved Thinwall steel sprinkler pipe. With EPDM EA gasket (violet stripe). For installation with cast rigid insert placed in the bolt pocket, according to the manufacturers instructions. With EPDM EP gasket with pre-lubricated material.
a, b, c c, f c, e, g, i, j c, d, h c
300 (2070) 175 (1205) 300 (2070) 300 (2070) 175 (1205)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. b. c. d. e. f. g. h. i. j. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket. When joining Allied Tube & Conduit XL threadable Thinwall pipe. FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. For use with Central Sprinkler TL threadable Thinwall pipe, Allied BLT and Wheatland WLS. For use on Northwest EZ Flow non-threadable Lightwall pipe in 4 in. nominal size. For use with Bull Moose Tube EDDY-Flow pipe.
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Style 5*
2-3 2-4 2
c, l c, d, m c, g
FM Approvals
1-277
Product Designation
Pipe Ends
Remarks
2-8 3-8 2
Rolled Groove
a, b, c c, n c, o, p
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With standard EPDM gasket, or dry lubricant EPDM gasket. d. Allied Dyna-Flow. g. Bull Moose EDDY-Lite. l. Allied XL. m. Allied Super-Flo. n. Tex-Tube Tex-Flow Lightwall pipe. o. Western International Forest Products Fire Thread threadable Thinwall pipe. p. Western International Forest Products Fire Flow non-threadable Lightwall pipe.
Qingdao V-Cart Piping Systems Co Ltd, JuiZhao Road, NanGuan Industry Zone, JiaoZhou City, Qingdao, China
Product Designation Nominal Pipe Size, in. or mm Pipe Ends Max Working Pressure, psi (kPa)
Remarks
a, b, c, d a, b, c, d a, b, c, d
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with GB/T 3091-93 or GB/T 8163-99 Pipe.
Robor Pipe Systems, Box 1098 Isando, Gauteng 1600, South Africa
Style STEELGRO R75 Grooved.
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Pipe Couplings*
1-8 1, 114
Cut Groove Rolled Groove Rolled Groove Rolled Groove Cut Groove
a, b, c c, f c, e, g, i, j c, d, h c, d c, k
300 (2070) 175 (1205) 300 (2070) 300 (2070) 175 (1205) 300 (2070)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. When joining Allied Tube & Conduit XL threadable Thinwall pipe. e. FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. f. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. g. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use with Central Sprinkler TL threadable Thinwall pipe, Allied BLT and Wheatland WLS. i. For use on Northwest EZ Flow non-threadable Lightwall pipe in 4 in. nominal size. j. For use with Bull Moose Tube EDDY-Flow pipe. k. For use with BS 1387 medium and heavy pipe, or equal.
SCE Company Ltd, Unit E&F, 20/F., CDW Building, 388 Castl Peak Road, Tsuen Wan, N.T., Hong Kong
Product Designation Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Remarks
2,
212,
3, 4, 5, 6
76.1, 165 mm
a, b, c a, b, c
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30.
FM Approvals
1-278
b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. c. Approved when supplied with EPDM gasket.
SPT Metal Corp, 19-1 Da Yeh St, Da Liao Hsiang, Kaohsiung Hsien, Taiwan ROC
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
501 Standard Rigid * 501 Standard Rigid * 502 L.W. Rigid * 502 L.W. Rigid * 502 L.W. Rigid *
114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 212 BS, 5 BS, 6 BS 112-4 112-6 114, 8
Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove
c, k c, d c, e, f, g, h, i, j, m a, b, c c, k
300 (2070) 300 (2070) 175 (1205) 175 (1205) 300 (2070)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. c. With EPDM gasket. d. British Standard Pipe e. When joining Allied Tube & Conduit XL threadable Thinwall pipe, 1-2 in. only. f. For use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. g. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. i. For use with Central Sprinkler TL threadable Thinwall pipe. j. For use with Bull Moose Tube EDDY-Flow pipe. k. For use on Schedule 40 Cut Groove and Rolled Groove only. m. For use with Wheatland Mega-Flow non-threadable Thinwall pipe.
Shanghai Recomb Piping System Co Ltd, No. 270 Yixian Rd, Shanghai 200434, P.R. China
Product Designation Pipe Actual Size mm Pipe Ends Remarks Max Working Pressure, psi (kPa)
XGQT1 XGQT1
33.7, 42, 48, 60, 73, 76, 89, 108, 114, 133, 140, 141.3, 159, 165, 168 and 219 273 and 325
Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove Rolled Groove, Cut Groove
a, b, c a, b, c
300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205)
a, b, c a, b, c a, b, c a, b, c a, b, c
a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Shanghai Vision Mechanical Joint Co Ltd, Jinlan Road, Loutang Industrial Park, Jiading District, Shanghai 201807 PRC
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
001
a, b, c, d, e
300 (2070)
FM Approvals
1-279
Product Designation
Pipe Ends
Remarks
001
Remarks: a. b. c. d.
a, b, c, d, e
300 (2070)
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. With EPDM gasket. For use with Chinese Standard GB/T 3091-1993, GB/T 3092-1993 welded steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30). e. For use with Chinese Standard GB/T 17395-1998 seamless steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30).
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
K-9* K-9* K-9 K-9H 7771* 7771* 7771* 7771 7771 7771 R20 SS-7 C301 Z05 Z05 Z05 Z05 Z05 Z07 Z07 Z07 Z07 Z07 Z07
114 through 6 114 through 8 212, 5, 6 8 1 1 2 2 through 8 10 12 14, 16, 18, 20 22, 24 114, 12, 2, 212, 3, 4, 5, 6 114, 112, 2, 212, 3, 5, 6, 8
c, d, e, f, h, j, l, m, p, r, s, t, w a, b, g, q, s f, s a, b, s a, b, s a, b, s a, b, s a, b, s a, s a, s, u a, b, c, d, e, f, p, q, s, w a, b, s a, b, i, s a, b, s a, b, s, x a, b, c, s a, b, g, s, y a, b, s a, b, s a, b, s a, b, s a, b, s, x a, b, g, s, y a, b, s
112,
2,
212,
175 (1205) 300 (2070) 300 (2070) 300 (2070) 500 (3447) 300 (2070) 200 (1375) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 200 (1380) 350 (2410) 350 (2410) 300 (2070) 300 (2070) 175 (1205) 500 (3447) 400 (2760) 350 (2410) 350 (2410) 300 (2070) 175 (1205)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10. c. Allied Super-Flo, Allied Dyna-Flow, 4 in. or smaller. d. Allied Super 40, Super-XL, 114 through 3 in. e. Bull Moose EDDY-LITE, 114 through 2 in. f. BS 1387 medium or heavy grade, 114, 112, 2, 212, 3, 4, 5, 6 in. g. Bull Moose Tube EDDY-Flow pipe, 114 through 4 in. h. American Tube BLT, 114 through 2 in. i. For use with copper tubing in K type pipe. j. American Tube Dyna-Thread 114 through 2 in. k. Super-XL, 114 through 3 in. l. Allied Tube XL-II, 114 through 3 in. m. Central TL, 112 through 2 in. p. Wheatland WST, 114 through 2 in. q. Fire-Thread, 112 through 2 in. r. Fire-Flow, 114, 112, 4 in. s. EPDM gasket.
FM Approvals
1-280
t. IDOD Systems Gal-5, 114 through 2 in. u. Schedule 20. v. Schedule 30. w. Bull Moose Ultra-EDDY, 2 in. or smaller. x. Allied Tube XL y. Wheatland Mega-Flow, 114 through 4 in.
Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove
a, b, c, d a, b, c, f a, b, c, f
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket (green Stripe) For use with Korean KS D3507 pipe. For use with metric OD pipe.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
Grinnell 7400*
Rolled Groove, Cut Groove Rolled Groove Rolled Groove, Cut Groove
a, b, c, d, e, f, j a, b, c c, n c, h
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in areas subject to earthquake. a. b. c. d. e. f. h. j. n. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket (green or violet stripe). Min schedule pipe to be joined: 3 in. or smaller Allied Tube & Conduit FM Approved XL, Super-XL and Super-40 Thinwall pipe. Min schedule pipe to be joined: Allied Tube & Conduit Dyna-Flow Lightwall pipe, 1-3 in. Min schedule pipe to be joined: Allied Tube & Conduit Super-Flo Lightwall pipe, 1-4 in. Metric Pipe: Equivalent to 76.1, 108, 133, 139.7, 159 and 165.1 mm. British Standard 1387, medium or equal. For use with Central Sprinkler TL threadable Thinwall pipe. Tex-Tube Tex-Flow Lightwall pipe. Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Product Designation
Remarks
572
114-8
Rolled Groove Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove Rolled Groove
a, b, c, e, q
300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 175 (1205)
114-6 114-2 114-4 6 577 1-8 1-6 1-2 1-2, 6 76, 139, 165 mm 772 114-2 112-4 114-6 114-4 114-212
c, e, f, j, u c, e, g, h, p, r, s, t c, e, o, p c, e, l a, b, c, e, n c, e, f, i, c, e, g, h, o, p, r, s, t c, e, j, l, m, u c, e, n, v c, p, v a, b, c, e c, e, f, l, q c, o, e, w c, e, j, m, u
FM Approvals
1-281
Product Designation
Pipe Ends
Remarks
Cut Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
c, e, g, h, r, s, t c, p b, c, e b, c, e a, c, e a, c, e a, c, e a, b, c, e c, e, n
300 (2070) 300 (2070) 300 (2070) 400 (2760) 300 (2070) 400 (2760) 450 (3105) 250 (1725) 300 (2070)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket (green stripe). For use with standard lubricant or dry lubricant. e. Also available with Tri-Seal EPDM gasket. Recommended by the manufacturer for dry systems. For use with standard lubricant or dry lubricant. f. For use with Allied Tube & Conduit Dyna-Flow, Northwest EZ-Flow and Allied Super-Flo non-threadable Lightwall pipe, in sizes up to 4 in. NPS. g. For use with Allied Tube & Conduit BLT threadable Thinwall pipe, in 6 in. NPS size. h. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. i. For use with Wheatland WLS. j. For use with Bull Moose Ultra-EDDY Schedule 5 pipe. l. For use with Northwest EZ-flow Pipe in 6 in. NPS size. m. For use with IDOD Systems Sch. 5 Pipe. n. For use with BS 1387 medium and heavy wall pipe. o. For use with Youngstown Tube Co. Fire-Flo non-threadable Lightwall steel sprinkler pipe. p. For use with Youngstown Tube Co. EZ-Thread threadable Thinwall steel sprinkler pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. v. For use with IDODs Gal-7 and Gal-Flo pipe. w. For use with Bull Moose EDDY-flow non-threadable Lightwall pipe.
005*
114-4 5-8
a, c, g, k, l, t a, c, g, k i, m, o, q, s, z, aa a, k, p, aa e, i, aa d, e, u, aa a, c, k, aa a, c, k, aa a, k, aa a, b, e, k, n, aa a, e, w, r, aa a, c, g, k, aa a, c, g, k, l, o, p, q , aa a, k, l, p, aa a, *, k, l, o, q, t, aa a, e, f, k a, e, k, y , aa a, e, r, aa
005H*
1 1 4,
112,
005H*
76, 108, 133, 139.7, 159, 165 mm 112, 2, 212, 3, 4 114-2 114-112 2-3 114, 112, 2, 212 139, 216 mm 3-8 6
350 (2415) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 350 (2415) 300 (2070) 175 (1205) 350 (2415) 300 (2070) 300 (2070) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070)
FM Approvals
1-282
Product Designation
Pipe Ends
Remarks
009*
114,-4
Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove 3, 4 Cut Groove
07* 07 Zero-Flex
267, 318 mm 1, 2, 3, 4, 6 14, 112, 2 1, 1 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2, 2 212, 112, 212,
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 500 (3445) 450 (3105) 300 (2070) 400 (2760) 500 (3445) 400 (2760) 500 (3445) 300 (2070) 175 (1205) 450 (3105) 400 (2760) 350 (2415) 175 (1205) 300 (2070) 300 (2070) 750 (5170) 700 (4825) 500 (3445) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 250 (1725)
112,
112, 2, 212, 3, 4 112, 2, 212, 3, 4 1, 114, 112, 2, 212, 3, 4, 5, 6 8 1-2 10, 12 1, 1 1 4, 112, 2, 212, 3, 4 5, 6, 8 6 6 6 1 2 8 10, 12 10, 12 76, 108, 133, 139.7, 159 mm 216 mm, HP-70 2-4 2-8 10, 12 2-12 HP-70ES 008 Stainless Steel Coupling 2-8 3-8 in.
Rolled Groove Cut Groove Rolled Groove Special Rolled Groove Cut Groove Rolled Groove
a, c, e, aa t, aa a, c, e, aa a, e, g, aa a, e, g, aa a, c, e, aa a, e, r, aa b, c, e, aa a, c, e, aa a, c, e a, e, g a, b, n, aa a, e, f, k q, z, aa a, c, e, aa a, c, e a, g, aa v* a, e, g c, h, k a, e, g c, h, k
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. Also available with Style 77FS gasket. Recommended by manufacturer for use with dry pipe systems. b. For steel pipe having metric sized outside dia. (ref. DIN 2448 & 2458). c. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. d. For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. e. With gasket E (green stripe), H (white stripe) or L (solid red), using standard gasket lubricant or Vic-Plus dry lubricant. f. For use with JIS steel pipe. g. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. h. For use with Schedules 10 and 40 stainless steel pipe. i. For use with Welded TubeBerkeley LLC Steady Flow non-threadable Lightwall steel sprinkler pipe in sizes 114, 112, 2, 212, 3, and 4 in. NPS. j. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. k. With gasket E, Grade A (violet stripe) with or without dry lubricant . l. For use with Allied Tube & Conduit XL and BLT threadable Thinwall pipe. m. For use with Welded TubeBerkeley LLC Steady Thread threadable Thinwall steel sprinkler pipe in sizes 1, 114, 112, and 2 in. NPS. n. For steel pipe having outside dia. sized per British Standard 1387, medium or equal. o. For use on Allied Tube & Conduit Dyna-Flow and Super-flo non-threadable Lightwall pipe. p. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co.
FM Approvals
1-283
q. For use with IDOD Systems Gal-7 and Gal-flo pipe, 114-2 in. sizes. r. For use on Wheatland Mega-Flow pipe. s. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 and 6 in. nominal size. u. For use with Bull Moose Tube EDDY-Flow pipe. v. For use on Schedules 10 and 40 pipe with end seal grooves only. Not for use with standard rolled or cut grooves. Not for use with hydrocarbon based fluids. x. For use with IDOD Systems Gal-5 and All-Gal pipe, 114-2 in. sizes at 175 psi. y. Tex-Tube Tex-Flow Lightwall pipe. z. For use with Western Fire-Flow and Fire-Thread pipe. aa. For use with VicMax EPDM Gaskets in 2 through 8 in. and 76 and 165 mm sizes. aaa. = For use with EDDY-lite and EDDY-thread pipe made by Bull Moose Tube. bb. = For use with GL, WLS and MLT pipe made by Wheatland Tube. cc. = For use with WST pipe at 175 psi, as made by Wheatland Tube. dd. = For use with Ultra-EDDY pipe at 175 psi, as made by Bull Moose Tube. ee. = For use with Dyna-light pipe at 175 psi, as made by Allied Tube & Conduit. ff. = For use with Allied Tube & Conduit Dyna-thread threadable Thinwall pipe. gg. = For use with Wheatland Tube Mega-thread threadable Thinwall pipe.
005*
114-112 2-3 114, 112, 2 114, 112, 2, 212, 3, 4, 6 114, 114, 112, 2, 2, 212, 3
Rolled Groove Cut Groove Rolled Groove 3 212, Cut Groove Rolled Groove 2, Rolled Groove Cut Groove Rolled Groove
a, c, g, k, l, o, p, q a, k, l, p a, k, l, t o, q, s l, p a, g a, c, k a, b, n b, c, e, g o, q, s a, e, l, p a, e, l u a, c, e a, c, e t a, c, e a, e, g a, e, g a, c, e b, c, e a, c, e a, c, e a, e, g a, b, n q a, c, e a, c, e a, g
112,
212,
3, 4, 5, 6
114, 112, 2, 212, 3, 4, 5. 6 76, 108, 133, 139.7, 153, 159 mm 165 mm, 8 07 Zero-Flex* 1, 112, 2, 212, 3, 4, 6
2, 3, 4, 5, 6 8 1-2 10, 12
112,
1,
114,
112,
212, 3, 4 5, 6, 8 6 612 8 10, 12 10, 12 76, 108, 133, 139.7, 159 mm 2-4 2-8 10, 12 2-12
HP-70*
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 500 (3445) 450 (3105) 300 (2070) 400 (2760) 500 (3445) 400 (2760) 500 (3445) 175 (1205) 450 (3105) 400 (2760) 350 (2415) 175 (1205) 300 (2070) 750 (5170) 700 (4825) 500 (3445)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. b. c. e. g. k. Also available with Style 77FS gasket. Recommended by manufacturer for use with dry pipe systems. For steel pipe having metric sized outside dia. (ref. DIN 2448 & 2458). Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. With gasket E (green stripe), H (white stripe) or L (solid red). Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. With gasket E, Grade A (violet stripe).
FM Approvals
1-284
l. When joining Allied Tube & Conduit XL threadable Thinwall pipe. n. For steel pipe having outside dia. sized per British Standard 1387, medium or equal. o. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. p. For Schedule 5 non-threadable Lightwall pipe as manufactured by Bull Moose Tube Co. q. When joining Allied Tube & Conduit Super-flo non-threadable Lightwall pipe. s. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. t. For use with Central Sprinkler TL threadable Thinwall pipe. u. For use with Bull Moose Tube EDDY-Flow pipe.
a, b, c, e, f, h, j c, d a, b, c a, b, c a, b, c c, d
300 (2070) 300 (2070) 500 (3445) 300 (2070) 250 (1725) 300 (2070)
*For installation where greater rigidity of pipe system is required. Not for use as flexible joints in locations subject to earthquake. a. b. c. d. e. f. h. j. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For metric pipe per BS 1387 medium or heavy. For use on Wheatland Mega-Flow pipe. All FM Approved for use on Allied Tube & Conduit Dyna-Flow and Super-Flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size at 250 psi (1725 kPa). For use with Bull Moose Tube EDDY-Flow pipe.
Weifang 100tong Casting Co Ltd, No. 1919 Jinchang South Road, Weicheng District, Weifang, Shandong, PR China 261052
Product Designation Nominal Pipe Size, mm Pipe Ends Rated Working Pressure, psi (kPa)
Remarks
GCQT1
33, 42, 48, 60, 76, 89, 108, 114, 133, 140, 159, 165, 168, 219
a, b, c, d, e, f
230 (1600)
a. b. c. d. e.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket. For use with BS 1387 medium or equal metric pipe. For use with Chinese Standard GB/T 3091-1993, GB/T 3092-1993 welded steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30). f. For use with Chinese Standard GB/T 17395-1998 seamless steel pipe with pipe wall thicknesses comparable to same size ASME B16.10M-2000, Schedule 40 pipe (8 in. NPS Schedule 30).
Style 25
2112; 2122 32; 3212; 42; 4212; 43; 64 2112; 2112-3212 2112-43
a, b, c
300 (2070)
c, g l, c m, d, c
FM Approvals
1-285
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. Allied Dyna-Flow. g. Bull Moose EDDY-Lite. l. Allied XL. m. Allied Super-Flo.
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Working Pressure, psi (kPa)
Gruvlok 7010
2112; 2122; 32, 212; 42, 212, 3; 53, 4; 64, 5; 86 2112 762, 376, 476, 1653, 4; 8165
a, b, c, d, e, h, i, j, k, l, n, o, p, r, s c, t a, b, c, d, e, h, i, j, k, l, n, o, p, r, s
7010E
a. b. c. d. e. h. i. j. k. l. n. o. p. r. s. t.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket (green stripe). 3 in. and smaller connections can be made to rolled grooved Allied Tube & Conduit FM Approved XL, XL-II, Super-XL and Super-40 Thinwall pipe. Min pipe Schedule Pipe to be joined: a) Allied Tube & Conduit Dyna-Flow Lightwall pipe. b) Allied Tube & Conduit Super-Flo Lightwall pipe, Allied Tube and Conduit Dyna-thread pipe, Allied Tube and Conduit BLT pipe. Bull Moose EDDY-Lite, EDDY-thread, and EDDY-flow pipe. at 300 psi. British Standard BS 1387 Pipe, or EN10255 pipe. IDOD Systems Gal 7 and Gal-flow pipe. Northwest Pipe EZ-flow pipe. Tex-Tube Co. Tex-flow Pipe in 212, 3, and 4 in. at 300 psi, and 6 in. at 175 psi. Welded Tube-Berkeley Steady-flow and Steady-thread pipe. WIFP Fire Line Flow and Fire Line Thread pipe. Wheatland WLS, Mega-flow, GL, MLT, and Mega-thread pipe. Yieh Phui Enterprise SPS Pipe. Youngstown Tube Fire Flow and Fire-thread pipe. Approved for use with Schedule 5 pipe.
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
RC-1
RC-2
RC-2
Remarks:
2112 2122 32, 212 42, 212, 3 64 86 2112 2122 32 42 2112 2122 32, 212 42, 212, 3 53, 4 64 86 2112
a, b, c, d, e, f, g, i, l, m, n
300 (2070)
Rolled Groove
b, c, j, t
175 (1205)
a, b, c, d, e, f, i, j, k, l, m, n, o, p, r, s
300 (2070)
Rolled Groove
c, t
175 (1205)
a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S, 8 and 10 in. NPS, 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with Allied Tube and Conduit Super-Flo and Dyna-Flow, Dyna-thread, and BLT Lightwall steel sprinkler pipe. e. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe. f. For use with Allied Tube and Conduit XL, XL-II, Super XL, and Super 40 threadable Thinwall steel sprinkler pipe. i. For use with Wheatland Tube WLS, Mega-flow, GL, MLT, Mega-thread threadable Thinwall steel sprinkler pipe. k. For use with Bull Moose Tube EDDY-Flow, EDDY-thread, EDDY-Light Lightwall steel sprinkler pipe. l. For use with Western International Forest Products Fire Line Flow, Fire Line Thread Lightwall steel sprinkler pipe. m. For use with Western International Forest Products Rapid-Thread threadable Thinwall steel sprinkler pipe in sizes: 112 and 2 in. NPS. n. For use with Welded TubeBerkeley LLC Steady Flow and Steady-thread Lightwall steel sprinkler pipe. o. Tex-Tube Co. Tex-flow Pipe in 212, 3, and 4 in. at 300 psi, and 6 in. at 175 psi. p. IDOD Systems Gal 7 and Gal-flow pipe. r. Yieh Phui Enterprise SPS Pipe. s. Youngstown Tube Fire Flow and Fire-thread pipe. t. Approved for use with Schedule 5 pipe.
FM Approvals
1-286
Style 25
a, b, c
300 (2070)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang Tsun Ta Liau Shiang Kaohsiung Hsien, Taiwan ROC
DUCCO Brand Couplings GT-412 Reducing Coupling 2112; 2122; 32, 212; 42, 212, 3; 54; 64; 86 Cut Groove, Rolled Groove a, b, c 300 (2070)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
FireShield Series 300 Products.
Style 25 2 1, 114, 112; 212 2; 3 2, 212, 76 mm; 4 2, 212, 3, 76 mm; 6 4; 2 112 through 4 3 76 mm 2, 165 mm 4 8 by 6, 165 mm Cut Groove Rolled Groove a, b, c, h, p, r, s, t 300 (2070)
c, e, k, j, m a, b, c, i a, b, c, i
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with Northwest EZ-Flow e. Allied Dyna-Flow h. Bull Moose EDDY-Lite i. British Standard BS 1387 Pipe, Med. and Heavy. j. Allied XL k. Allied Super-Flo m. Central Sprinkler TL pipe o. IDOD Gal-7 p. Tex-Tube Tex-flow r. Western International Fire-Thread and Fire-Flow s. Northwest EZ-Flow t. Welded Tube Berkeley, LLC Steady-Flow
JFE Pipe Fitting Mfg Co Ltd, 153 Tajime-Cho, Kishiwada Osaka, Japan
Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure, psi (kPa)
7706
2112, 3 OD2, 2122, 32, 3212, 33 OD, 42, 4212, 43 OD, 43, 54, 612 OD3, 63, 612 OD4, 64, 86, 8612 OD
a, b, c
300 (2070)
a. Min schedule cut groove pipe to be joined: 8 in. or smaller Schedule 40 b. Min schedule Rolled groove pipe to be joined: 8 in. or smaller Schedule 10 c. British Standard BS 1387 medium or heavy grade pipe.
FM Approvals
1-287
Product Designation
Pipe Ends
Remarks
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
71 2112 32 42, 3 63, 4 86 7660 mm 8976 mm 11476 mm 140114 mm 16589, 114 mm 219165 mm Cut Groove, Rolled Groove a, b, c, d, e 250 (1725)
a, b, c, d, e
250 (1725)
Remarks: a. b. c. d. e. Minimum schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 Wall (5 mm Wall). With EPDM EP gasket (green stripe). For use with DIN 2448 and 2458 steel pipe. With EPDM EP gasket with pre-lubricated material.
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
FireShield Series 300 Products.
Style 25 2112; 2122 32; 3212; 42; 4212; 43; 64 2112 21123212 211243 76212, 3, 4 1654 Cut Groove Rolled Groove a, b, c 300 (2070)
Rolled Groove
c, g c, l c, d, m a, b, c, k
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. Allied Dyna-Flow. g. Bull Moose EDDY-Lite. k. British Standard BS 1387 Pipe. l. Allied XL. m. Allied Super-Flo.
SPT Metal Corp, 19-1 Da Yeh St, Da Liao, Hsiang, Kaohsiung Hsien Taiwan, ROC
Style 506 112114 2112 2122 32 3212 42, 212, 3 54 64, 5 86 112114 through 43 Cut Groove Rolled Groove a, b, c 300 (2070)
Rolled Groove
c, e, f, g, h, i, j
300 (2070)
a. b. c. e. f. g. h. i. j.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. When joining Allied Tube & Conduit XL threadable Thinwall pipe, 1-2 in. only. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. For use with Central Sprinkler TL threadable Thinwall pipe. For use with Bull Moose Tube EDDY-Flow pipe.
FM Approvals
1-288
Product Designation
Pipe Ends
Remarks
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
7706 2112, 3 OD2, 2122, 32, 3212, 33 OD, 42, 4212, 43 OD, 43, 54, 612 OD3, 63, 612 OD4, 64, 86, 8612 OD Rolled Groove Cut Groove a, b, c 300 (2070)
a. Min schedule cut groove pipe to be joined: 8 in. or smaller Schedule 40. b. Min schedule Rolled groove pipe to be joined: 8 in. or smaller Schedule 10. c. British Standard BS 1387 medium or heavy grade pipe.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Grinnell 7010 2112; 2122; 32, 212; 42, 212, 3; 53, 4; 64, 5; 86 2112 Cut Groove, Rolled Groove a, b, c, d 300 (2070)
Rolled Groove
c, e
175 (1205)
a. b. c. d. e.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket (green stripe). 3 in. and smaller connections can be made to rolled grooved Allied Tube & Conduit FM Approved XL, Super-XL and Super-40 Thinwall pipe. Min pipe Schedule Pipe to be joined: a) Allied Tube & Conduit Dyna-Flow Lightwall pipe; b) Allied Tube & Conduit Super-Flo Lightwall pipe.
2112
a, c
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070)
2122; 3212 32 42, 212, 3 54 64, 5; 86; 2112 2122 32, 212 32 through 43 42, 212, 3 54; 64, 5 64, 5; 86 2112 through 43 2112 through 64 76 mm2 376 mm 476 mm 139 mm4 165 mm5
a, c a, c a, c a, c a, c b, c, g, h, i, j, m, o, p, q, r, s, t, v c, m
c, m c, k, u c, n c, d, n, w
FM Approvals
1-289
Product Designation
Pipe Ends
Remarks
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket (green stripe). For use with standard lubricant or dry lubricant. e. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. d. For use with BS 1387 medium and heavy pipe. f. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. g. For use with Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use with Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. i. For use with Central Sprinkler TL threadable Thinwall pipe. j. For use with Central 7 non-threadable Thinwall pipe. k. For use with Schedule 5 pipe, including IDOD Systems galv. coated pipe. l. For use with Central 7 pipe. m. For use with 4 in. Northwest EZ-Flow pipe. n. For use with Welded Tube Berkeley LLC Steady-flow pipe. o. For use with Youngstown Fire-Flo Pipe. p. For use with Youngstown EZ-Thread Pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. v. For use with IDODs Gal-7 and Gal-Flo pipe. w. For use with ISO 4200 steel sprinkler pipe. Figure 716 2112 2122; 3212 32 42, 2 1 2, 3 Rolled Groove, Cut Groove Rolled Groove a, c a, c a, c a, c a, c a, c b, c, g, h, m, o, p, q, r, s, t, v c, m 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070)
54 64, 5; 86; 2112 2122 32, 212 32 through 43 42, 212, 3 54; 64, 5 64, 5; 86 2-4 2112 through 64 Figure 716 76 mm by 2, 3 by 76 mm, 4 by 76 mm, 139 by 4, 165 by 5
c, m c, u c, n, w c, x, y
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket (green stripe). For use with standard lubricant or dry lubricant. e. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. f. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. g. For use with Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use with Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. m. For use with 4 in. Northwest EZ-Flow pipe. n. For use with Welded TubeBerkeley LLC Steady-Flow pipe. o. For use with Youngstown Fire-Flo Pipe. p. For use with Youngstown EZ-Thread Pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. v. For use with IDODs Gal-7 and Gal-Flo pipe. w. For use with Bull Moose Tube Co. EDDY-flow non-threadable Lightwall pipe. x. For use with BS 1387 Medium and Heavy pipe. y. For use with ISO 4200 steel sprinkler pipe.
FM Approvals
1-290
Product Designation
Pipe Ends
Remarks
2112; 2122; 32, 212; 42, 212, 3; 54; 64, 5; 86 2-4 2112; 2122; 32, 212; 42, 212, 3
a. c. d. f. g. h. i. j. k.
Rolled Groove
c, d
c, d, f
g, i, k d, h
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With gasket E (green stripe), H (white stripe) or L (solid red), using standard gasket lubricant or Vic-Plus dry lubricant. When joining Allied Tube & Conduit Super-Flo Lightwall non-threadable pipe, up to 4 in. dia., 200 psi (1380 kPa) limit. With Allied Tube & Conduit Dyna-Flow. For use with Central 7 pipe. For use with Western Fire-Flow and Fire-Thread pipe. For use with Bull Moose EDDY-Flow pipe. For use on Wheatland Mega-Flow pipe.
Rolled Groove
c, d
c, d, f
300 (2070)
a. c. d. f. g.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With gasket E (green stripe), H (white stripe) or L (solid red). When joining Allied Tube & Conduit Super-Flo Lightwall non-threadable pipe, up to 4 in. dia., 200 psi (1380 kPa) limit. With Allied Tube & Conduit Dyna-Flow.
c, d
300 (2070)
a. b. c. d.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with BS 1387 medium or heavy pipe.
FM Approvals
1-291
EO Model DS2
EO Model DS1
EO Model DD1
EO Model DD2
EO Model DD3
212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 14, 112, 2, 212, 3 41 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 14, 112, 2, 212, 3 41 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4
a, c
300 (2070)
a, b, c
300 (2070)
a, c
300 (2070)
a, b, c
300 (2070)
a, b, c
300 (2070)
Remarks: a. For use on Schedule 10 and heavier steel sprinkler pipe. b. Approved when supplied with NPT female threads. c. Approved when supplied with EPDM gasket.
16
212 3 4 6
Style 15G Snap-Tee Branch Outlet. For working pressure of 300 psi (2070 kPa) for the 3, 4 in. run sizes and working pressure of 250 psi (1725 kPa) for 6 in. run size. For use on Schedule 10 or heavier pipe. Grooved outlet connection clamps over hole in pipe wall.
15G Snap-Tee Branch Outlet 112, 2 112, 2, 212, 3 112, 2, 212, 3, 4 3 4 6
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Gruvlok Clamp-T. For use with Schedule 10S or heavier pipe*, in 6 in. or smaller sizes and 0.188 in. (5 mm) wall or heavier pipe, in the 8 in. size. With EPDM gasket (green stripe) only.
*Pressure ratings vary by size: Nominal Pipe Size, in. Pressure rating, psi (kPa)
212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 4114, 112, 2, 212; 8212, 3 3114, 112, 2; 43; 5114, 112, 2, 212, 3; 6114, 112, 2, 212, 3 312, 34, 1; 412, 34, 1; 64; 84
Central Sprinkler TL 2 in. size, 300 psi (2070 kPa).
FM Approvals
1-292
Product Designation
Fitting Description
Remarks
7044
7045
11412, 34, 1 11212, 34, 1 212, 34, 1 21212, 34, 1 212, 34, 1, 114, 112 21212, 34, 1, 114, 112 Not Applicable 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2 Not Applicable 4212, 3 Not Applicable 5114, 112, 2, 212, 3 Not Applicable Not Applicable 6114, 112, 2, 212 Not Applicable 63, 4 8212, 3, 4 Not Applicable 212, 234, 21, 2114, 2112, 21212, 21234, 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 4212, 43, 6114, 6112, 62, 6212, 63, 64
7045
7045T
60.321.3, 26.7, 33.4, 42.4, 48.3 73.021.3, 26.7, 33.4, 42.4, 48.3 76.121.3, 26.7, 33.4, 42.4, 48.3 88.921.3, 26.7, 33.4, 42.4, 48.3, 60.3 114.321.3, 26.7, 33.4, 42.4, 48.3, 60.3 114.376.1 114.373.0, 88.9 139.742.4, 48.3, 60.3, 73.0, 76.1, 88.9 141.342.4, 48.3, 60.3, 73.0, 88.9 141.376.1 165.142.4, 48.3, 60.3, 73.0, 76.1, 88.9, 114.3 168.342.4, 48.3, 60.3, 73.0 168.376.1 168.388.9, 114.3 219.173.0, 88.9, 114.3 219.176.1 175 (1205)
FM Approved with ANSI NPT thread or ISO thread as appropriate for the outlet pipe. 7046 Clamp-T With Grooved Outlet 2114, 112 212114, 112 Not Applicable 3114, 112, 2 4114, 112, 2, 212 Not Applicable 43 Not Applicable 5114, 112, 2, 212, 3 Not Applicable 6114, 112, 2, 212 Not Applicable 63, 4 8212, 3, 4 7046T Mechanical Tee Grooved Outlet 3112, 32, 4112, 42, 4212, 43, 6112, 62, 6212, 63, 64 60.342.4, 48.3 73.042.4, 48.3 76.142.4, 48.3 88.942.4, 48.3, 60.3 114.342.4, 48.3, 60.3, 73.0 114.376.1 114.388.9 139.742.4, 48.3, 60.3, 73.0, 88.9 141.342.4, 48.3, 60.3, 73.0, 88.9 165.142.4, 48.3, 60.3, 73.0, 76.1, 88.9, 114.3 168.342.4, 48.3, 60.3, 73.0 168.376.1 168.388.9, 114.3 219.173.0, 88.9, 114.3 175 (1205)
a. For use on Schedule 10 and heavier pipe. Product Designation Fitting Description Nominal Pipe Size, in. Remarks Nominal Pipe Size, mm
7043
114 12, 34, 1 112 12, 34, 1 2 12, 34, 1 212 12, 34, 1 114 12, 34, 1 112 12, 34, 1 2 12, 34, 1 212 12, 34, 1
a, c, g, h, l, m, n, q, r, s
300 (2070)
7043
e, k
175 (1205)
FM Approvals
1-293
Product Designation
Fitting Description
Remarks
7043E
114 12, 34, 1 112 12, 34, 1 2 12, 34, 1 212 12, 34, 1 114 12, 34, 1 112 12, 34, 1 2 12, 34, 1 212 12, 34, 1
a, c, g, h, l, m, n, q, r, s, t
300 (2070)
7043E
e, k
175 (1205)
Remarks a. b. c. d. e. f. g. For use with FM Approved Schedule 10 and 40 steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, 3, 4, 5, 6, and 8 in. NPS. For use with Youngstown Tube EZ-Thread threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Allied Tube and Conduit XL and XL-II threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, and 3 in. NPS. For use with Sawhill Tubular SLS threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Wheatland Tube WST Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3, 4, and 6 in. NPS. For use with Welded TubeBerkeley LLC Steady-Flow Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3. In addition, the MT-4 is FM Approved for use with 4 in. NPS Steady-Flow. h. For use with Wheatland Tube Mega Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. i. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 4 and 6 in. NPS. j. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. k. For use with Bull Moose Tube Ultra EDDY Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. l. For use with Bull Moose EDDY Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. m. For use with Allied Tube and Conduit BLT threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. n. For use with Bull Moose Tube EDDY-Lite threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. p. For use with Western International Forest Products Rapid-Thread steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. q. For use with Wheatland Tube WLS threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. r. For use with Western International Forest Products Fire Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 3, and 4 in. NPS. s. For use with Allied Tube and Conduit Dyna Flow and Super-Flo Lightwall sprinkler pipe in sizes: 112, 2, 2 12, 3, 4, and 6 in. NPS. t. For use with BS1387 Medium or Heavy steel pipe. Product Designation Fitting Description Nominal Pipe Size, in.
7047
212 3 4
114, 112 Not Applicable 114, 112, 2 114, 112, 2, 212 Not Applicable 3 Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable 3, 4 2, 212, 3, 4 Not Applicable
73.0 76.1 88.9 114.3 114.3 114.3 139.7 139.7 141.3 141.3 165.1 165.1 168.3 168.3 168.3 219.1 219.1
6 8
42.4, 48.3 42.4, 48.3 42.4, 48.3, 60.3 42.4, 48.3, 60.3, 73.0 76.1 88.9 42.4, 48.3, 60.3, 73.0 76.1 42.4, 48.3, 60.3, 73.0 76.1 42.4, 48.3, 60.3, 73.0 76.1, 88.9, 114.3 42.4, 48.3, 60.3, 73.0 76.1 88.9, 114.3 60.3, 73.0, 88.9, 114.3 76.1
Product Designation
Fitting Description
7048
212 3 4
48.3 42.4, 48.3 42.4, 48.3, 60.3 42.4, 48.3, 60.3, 73.0
FM Approvals
1-294
Not Applicable 3 Not Applicable 114, 112, 2, 212 Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable 3, 4 212, 3, 4
114.3 114.3 139.7 141.3 165.1 165.1 168.3 168.3 168.3 219.1
6 8
76.1 88.9 42.4, 48.3, 60.3, 73.0 42.4, 48.3, 60.3, 73.0 42.4, 48.3, 60.3, 73.0 76.1, 88.9, 114.3 42.4, 48.3, 60.3, 73.0 76.1 88.9, 114.3 73.0, 88.9, 114.3
Product Designation
Fitting Description
7049
Sizes of the Figure 7049 Clamp Tee Crosses can be formed with any combination of the sizes shown of Figure 7047 or 7048 Clamp Tee Crosses having the same run size.
Allied Tube & Conduit Super-Flo, 2 in. and Allied Tube & Conduit Dyna-Flow, 2 in. 175 psi (1205 kPa). Allied Tube & Conduit Super-Flo, 212-4 in. and Allied Tube & Conduit Dyna-Flow, 212-3 in. 300 psi (2070 kPa). Tex-Tube Co. Tex-Flow. 3-8 in. 300 psi (2070 kPa). Youngstown Tube Fire-Flo 112-4 in., and Youngstown Tube EZ-Thread 1-2 in., 300 psi (2070 kPa). Except 2 in. run sized items and 21212, 34, 1 in. sized branch connections.
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Rated Working Pressure, psi (kPa)
MT-1
21, 114, 112 2121, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 21, 114, 112 2121, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 5 x 112, 2, 212 6114, 112, 2, 212, 3, 4 3112, 2 4112, 2, 3, 76 mm 5 x 2, 212, 3 6112, 2, 212, 3, 4, 76 mm 3112, 2 4112, 2, 3, 76 mm 114 x 12, 34, 1 112 x 12, 34, 1 2 x 12, 34, 1 212 x 12, 34, 1 114 x 12, 34, 1 112 x 12, 34, 1 2 x 12, 34, 1 212 x 12, 34, 1 1 1 4 1 2, 3 4, 1 112 12, 34, 1 2 1 2, 3 4, 1 212 12, 34, 1 2 x 1, 114, 112 3 x 1, 114, 112, 2 4 x 1, 114, 112, 2, 76 mm 6 x 76mm 2 x 1, 114, 112
k, l
175 (1205)
MT-1
a, c, g, i, m, n, p, q, r, s
300 (2070)
MT-2
a, c, s
300 (2070)
MT-2
Mechanical Tee (Grooved End Outlet) Mechanical Tee Threaded Outlet (Female NPT)
MT-3
a, c, g, h, l, m, n, q, r, s
MT-3
e, k
175 (1205)
MT-30
300 (2070)
MT-8
a, b, c, i, m, n, q, s
300 (2070)
MT-8
175 (1205)
FM Approvals
1-295
Product Designation
Fitting Description
Remarks
MT-8
Mechanical Tee Threaded Outlet (BSP Threads) Mechanical Tee Threaded Outlet (ISO Threads) Mechanical Tee Threaded Outlet (Female ISO)
300 (2070)
MT-90
114 1, 212 1
300 (2070)
MT-90
114 12, 34, 1 112 12, 34, 1 2 1 2, 3 4, 1 76 mm 12, 34, 1 114 12, 34, 1 112 12, 34, 1 2 1 2, 3 4, 1 76 mm 12, 34, 1
a, c, g, h, l, m, n, q, r, s, t
300 (2070)
MT-90
a, c, g, h, l, m, n, q, r, s, t
175 (1205)
Remarks: a. b. c. d. e. f. g. For use with FM Approved Schedule 10 and 40 steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, 3, 4, 5, 6, and 8 in. NPS. For use with Youngstown Tube EZ-Thread threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Allied Tube and Conduit XL and XL-II threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, and 3 in. NPS. For use with Sawhill Tubular SLS threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Wheatland Tube WST Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3, 4, and 6 in. NPS. For use with Welded TubeBerkeley LLC Steady-Flow Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3. In addition, the MT-4 is FM Approved for use with 4 in. NPS Steady-Flow. h. For use with Wheatland Tube Mega Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. i. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 4 and 6 in. NPS. j. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. k. For use with Bull Moose Tube Ultra EDDY Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. l. For use with Bull Moose EDDY Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. m. For use with Allied Tube and Conduit BLT threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. n. For use with Bull Moose Tube EDDY-Lite threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. p. For use with Western International Forest Products Rapid-Thread steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. q. For use with Wheatland Tube WLS threadable thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. r. For use with Western International Forest Products Fire Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 3, and 4 in. NPS. s. For use with Allied Tube and Conduit Dyna Flow and Super-Flo Lightwall sprinkler pipe in sizes: 112, 2, 2 12, 3, 4, and 6 in. NPS. t. For use with BS1387 Medium or Heavy steel pipe.
Beijing Tian Ning Yi He Pipe System Equipment Co Ltd, No. 2, North Road, Ju Yuan, Ma Pa Ju Yuan Industrial Base, Shunyi District, Beijing, P. R. China
Product Designation Pipe Size, mm Fitting Description Remarks Max Working Pressure, psi (kPa)
GCQT3
114.3 x 60.3, 114.3 x 76.1, 114.3 x 88.9, 133 x 88.9, 139.7 x 60.3, 139.7 x 88.9 159 x 60.3, 159 x 76.1, 159 x 88.9, 159 x 108, 159x 114.3, 165.1 x 60.3, 165.1 x 76.1, 165.1 x 88.9, 165.1 x 108, 165.1 x 114.3, 219 x 76.1, 219 x 88.9, 219 x 108, 219 x 114.3 88.9 x 33.5, 88.9 x 42.4, 88.9 x 48.3, 108 x 33.5, 108 x 42.4, 108 x 48.3, 108 x 60.3, 114.3 x 33.5, 114.3 x 42.4, 114.3 x 76.1, 114.3 x 48.3, 114.3 x 60.3, 133 x 33.5, 133 x 42.4, 133 x 48.3. 133 x 60.3, 139.7 x 33.5, 139.7 x 42.4, 139.7 x 48.3, 139.7 x 60.3, 137.7 x 76.1, 139.7 x 88.9, 159 x 33.5, 159 x 42.4, 159 x 48.3, 159 x 60.3, 159 x 76.1, 159 x 88.9, 165.1 x 33.5, 165.1 x 42.4, 165.1 x 48.3, 165.1 x 60.3, 165.1 x 76.1, 165.1 x 88.9, 219 x 60.3, 219 x 76.1
a, b, c
175 (1205)
GCQT3
a, b, c
175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
FM Approvals
1-296
15
3 4 6
Style 16 Snap-Tee Branch Outlet. For working pressures up to 300 psi (2070 kPa). For use on Schedule 10 or heavier pipe. NPT internal outlet connection to Schedule 40 or heavier pipe. Clamps over hole in pipe wall.
16 Snap-Tee Branch Outlet 1, 114, 112, 1, 114, 112 1, 114, 112, 2, 1, 114, 112, 2, 212, 3 114, 112, 2, 212, 3, 4 2 212 3 4 6
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang Tsun Ta Liau Shiang Kaohsiung Hsien, Taiwan ROC
Side Outlet Coupling. For working pressures up to 300 psi (2070 kPa). For use on Schedule 10 or heavier pipe. NPT internal outlet connection to Schedule 40 or heavier pipe. Roll grooved outlet for Schedule 10 or heavier pipe. Clamps over hole in pipe wall.
Product Designation Nominal Pipe Size, in. Max Working Pressure, psi (kPa)
DUCCO Brand Outlet Tees GT-413A Grooved Branch Outlet GT-413B Internal NPT Outlet
3112, 2; 4112, 2, 212, 3; 62, 212, 3, 4; 84 21, 114, 112; 121, 114, 112; 2 31, 114, 112, 2; 41, 114, 112, 2, 212, 3; 62, 212, 3, 4 212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 31; 41
300 (2070)
300 (2070)
300 (2070)
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
Style 13 Mechanical Branch Outlet. For use on Schedule 10 or heavier pipe. NPT internal threaded outlet. Clamps over predrilled hole in pipe wall. 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
Style 13
114 12, 34, 1 1 1 2 1 2, 3 4 1 2 12, 34, 1 212 12, 34, 1 3 12, 34, 1 4 12, 34, 1 76 mm 12, 34, 1
Branch line sprinkler installation 1 in. outlet size only. Style 15 Snap-Tee Branch Outlet. Grooved outlet connection. Clamps over hole in pipe wall
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in.
Style 15
114, 112 2 1 1 2 114, 112, 2, 212, 3, 76 mm 114, 112, 2, 212, 3, 76 mm 114, 112, 2, 212, 3, 76 mm 112, 212, 3, 4, 76 mm 114, 112, 2, 212, 3, 4, 76 mm 2, 212, 3, 4, 76 mm 1 1 4, 112,
2 3 76 mm 4 5 139.7mm 6 165 mm 8
Product Designation
Remarks
Style 15
2 114 3 2
Grooved
c, l
300 (2070)
FM Approvals
1-297
Product Designation
Remarks
c, d, m a, b, c, n a, b, c c, k
a. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. b. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40. 8 in. or larger Sch. 30 c. With EPDM gasket. d. Allied Dyna-Flow. k. British Standard BS 1387 Pipe, Med. and Heavy. l. Allied XL. m. Allied Super-Flo. n. Northwest EZ-Flow
Style 16 Snap-Tee Branch Outlet. NPT internal outlet connection to Schedule 40 or heavier pipe. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Outlet Size, in.
1 2, 3 4, 1 2, 3 4,
Style 16
1, 114, 112
1, 114, 112, 2 1, 114, 112 12, 34, 1, 114, 112, 2, 212, 3, 76 mm 114, 112, 2, 212, 3, 76 mm 114, 112, 2, 212, 3, 76 mm 114, 112, 2, 212, 3, 4, 76 mm 114, 112, 2, 212, 3, 4, 76 mm 2, 212, 3, 4, 76 mm
1 2, 3 4,
Product Designation
Remarks
Style 16
c, l, p c, d, m, o, p c, g, p a, b, c, o, p c, k c, k
112
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. b. Min schedule cut groove pipe to be joined: 6 in. or smaller - Schedule 40; 8 in. or larger Schedule 30. c. With EPDM gasket. d. Allied Dyna-Flow g. Bull Moose EDDY-Lite k. British Standard BS 1387 Pipe, Med. and Heavy. l. Allied XL m. Allied Super-Flo o. Northwest EZ Flow p. Central Sprinkler TL
JFE Pipe Fitting Mfg Co Ltd, 153 Tajime-Cho, Kishiwada Osaka, Japan
Product Designation Nominal Pipe Size, in. Fitting Description Max Working Pressure, psi (kPa)
7721
7722
212, 234, 21, 2114, 2112, 21212, 21234, 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 4212, 43, 6114, 6112, 62, 6212, 63, 64, 8212, 83, 84 3112, 32, 4112, 42, 4212, 43, 6112, 62, 6212, 63, 64, 8212, 83, 84
Mechanical Tee
300 (2070)
Mechanical Tee
300 (2070)
FM Approvals
1-298
Product Designation
Fitting Description
Remarks
723 Saddle-Let
11412, 11434, 1141, 11212, 11234, 1121, 212, 234, 21, 21212, 21234, 2121, 11212, 11234, 1121, 212, 234, 21, 21 21212, 21234, 2121, 212114, 212112, 334, 31, 31, 3112, 434, 41, 4112, 42, 61, 6112, 6112, 62
a, b
300 (2070)
300 (2070)
Mechanical Branch Outlet. For use on Schedule 10 or heavier pipe. NPT internal thread outlet. Clamps over predrilled hole in pipe wall. 175 psi (1207 kPa) rated working pressure. The Model 723 Mechanical Tee may be used with Schedule 10 and heavier, plus:
Model Sizes, in.
Allied XL, Allied Super-Flow Allied BLT Allied Dyna-Flow Bull Moose Eddy-Lite Central TL Wheatland WLS
Jinan Meide Casting Co Ltd, No. 3 Nanmen Road, Pingyin, Jinan, 250400 China
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
3G
2114, 112 212114, 112 76114, 112 3114, 112, 2 4114, 112, 2, 212, 3 139.72, 212, 3 5114, 112, 2, 212, 3 1652, 212, 3 6114, 112, 2, 212, 3, 4 21, 114, 112 2121, 114, 112 761, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 139.71, 114, 112, 2 5114, 112, 2, 212, 3 1651, 114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 2114, 112 212114, 112 76114, 112 3114, 112, 2 4114, 112, 2, 212, 3 139.72, 212, 3 5114, 112, 2, 212, 3 1652, 212, 3 6114, 112, 2, 212, 3, 4
a, c
300 (2070)
3J
a, b, c
300 (2070)
4G
a, c
300 (2070)
FM Approvals
1-299
Product Designation
Fitting Description
Remarks
4J
21, 114, 112 2121, 114, 112 761, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 139.71, 114, 112, 2, 212, 3 5114, 112, 2, 212, 3 1651, 114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 21, 114, 112 2121, 114, 112 761, 114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4
a, b, c
300 (2070)
4JG
a, b, c
300 (2070)
Remarks: a. For use on Schedule 10 and heavier steel sprinkler pipe. b. Approved when supplied with NPT female threads. c. Approved when supplied with EPDM gasket. Product Designation Fitting Description Nominal Pipe Size Pressure Rating, psi (kPa)
90
90 Elbow
1, 114, 112, 2, 212, 3, 4, 5, 6, 8 1, 114, 112, 2, 212, 3, 4, 5 114, 112, 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 212, 3, 4, 5, 6, 8 4, 5, 6, 8 1, 114, 112, 2, 12, 3, 4, 5, 6, 8 2 1, 114, 112, 2, 212, 3, 4, 5 114, 112, 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 212, 3, 4, 5, 6, 8 4, 5, 6, 8 1, 114, 112, 2, 212, 3, 4, 5 114, 112, 2, 212, 3, 4, 5, 6, 8 112, 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 212, 3, 4, 5, 6, 8 3, 4, 5, 6, 8 4, 5, 6, 8 5, 6, 8 6, 8 8
3 4
1 1 1 4 1 1 2 2 2 1 2 1 2
3 4
1 1 1 4 1 1 2 2 2 1 2 3 4
1 1 1 4 1 1 2 2 2 1 2 3 4 5 6
Branch Connection for attachment to pipe by welding. For use with ISO 4200, DIN2440 and 2448, Schedule 10 or 40 Steel Sprinkler Pipe. Requires pre-cutting of hole on pipe. Rated Working Pressure is 20 bar (290 psi).
FM Approvals
1-300
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Model Nominal Size, mm (in.)
TXG 25.15 TXG 25.20 TXG 32.10 TXG 32.15 TXG 32.20 TXG 32.25 TXG 40.15 TXG 40.20 TXG 40.25 TXG 50.15 TXG 50.20 TXG 50.25 TXG 65.20 TXG 65.25
2515 (112) 2520 (134) 3210 (11438) 3215 (11412) 3220 (11434) 3225 (1141) 4015 (11212) 4020 (11234) 4025 (1121) 5015 (212) 5020 (234) 5025 (21) 6520 (21234) 6525 (2121)
Rated working pressure 16 BAR (232 psi). FM Approved for use with Schedules 10 and 40 pipe, DIN 2448 and 2458 pipe, ISO 4200 pipe and BS 1387 medium and heavy pipe for use in valve trim, and accessories, and in sprinkler system branch lines.
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
Quik-Tee Branch Outlet or Cross with NPT internal threaded or grooved outlet connections for use with Schedule 10 or heavier pipe to clamp over precut hole in pipe. 500 psi (3445 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in. or mm as noted Max Rated Pressure, psi (kPa)
Style 08
Style 08
Grooved Outlet
212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1, 114, 112, 2; 3122; 4114, 112, 2, 212; 6114, 112, 2, 212, 4 76 mm by 12, 34, 1, 114, 112 139 mm by 114, 112, 2, 76 mm 4 by 212, 3 6 by 212, 3
250 (1725)
For use with Schedules 10 and 40 pipe, and DIN 2448 or 2458 metric pipe. Product Designation Nominal Pipe Size, in. Outlet Connection Remarks Max Rated Pressure, psi (kPa)
08 Quik-Tee or Cross
140 mm114 in., 140 mm112 in., 140 mm2 in., 140 mm76 mm 114 mm3 in. BSP 165 mm3 in. BSP 168 mm3 in. BSP 114 by 12, 34, 1 BSP
Grooved Outlet
250 (1725)
Female Thread
250 (1725)
a. Mounts over hole in Schedule 40 or Schedule 10S pipe, or DIN 2448 or 2458 pipe.
QUIK-T Branch Outlet or Cross with NPT external threaded or grooved outlet connections for use with Schedule 10 or heavier pipe to clamp over precut hole in pipe. 250 psi (1725 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
08 QUIK-T
4, 6212
QUIK-HOOK Style 09 Sprinkler Outlet. For use on Schedule 10 or heavier pipe. 175 psi (1205 kPa) rated working pressure. NPT internal outlet connection. Clamps over hole in pipe wall.
FM Approvals
1-301
Product Designation
Fitting Description
09
Sprinkler Outlet
Style 09 Quik-Hook Sprinkler Outlet. For use on Schedule 10 or heavier pipe. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Run Pipe Size, in. Nominal Outlet Pipe Size, in.
1 2, 3 4
09
112, 2
Style 99 Sprinkler Outlet. For use on Schedule 10 or heavier pipe, or DIN pipe. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Run Pipe Size, in. Nominal Outlet Pipe Size, in.
1 2, 3 4,
99
114, 112, 2, 76 mm
1 NPT
Style 13
Branch line sprinkler installation 1 in. outlet size only. Style 15 Snap-Tee Branch Outlet. For working pressure of 300 psi (2070 kPa) for the 3, 4 in. run sizes and working pressure of 250 psi (1725 kPa) for 6 in. run size. For use on Schedule 10 or heavier pipe. Grooved outlet connection. Clamps over hole in pipe wall. Style 16 Snap-Tee Branch Outlet. For working pressures up to 300 psi (2070 kPa). For use on Schedule 10 or heavier pipe. NPT internal outlet connection to Schedule 40 or heavier pipe. Grooved outlet connection clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in.
Style 15
3 4 5 6 165 mm
Product Designation
Fitting Description
Remarks
Style 15
311232
c, l
300 (2070) 300 (2070) 300 (2070) 250 (1725) 175 (1205) 300 (2070) 250 (1725)
c, d, m, n a, b, c a, b, c c, k c, n c, n
Snap-Tee Branch Outlet. NPT internal outlet connection to Schedule 40 or heavier pipe. Clamps over hole in pipe wall.
FM Approvals
1-302
Product Designation
Fitting Description
Style 16
12, 34,
2, 212, 3 4 6 8 165 mm
Product Designation
Fitting Description
Remarks
Style 16
c, l c, d, m c, g a, b, c a, b, c c, k c, n c, n
300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 175 (1205) 300 (2070) 250 (1725)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. Allied Dyna-Flow. g. Bull Moose EDDY-Lite. k. British Standard BS 1387 Pipe. l. Allied XL. m. Allied Super-Flo. n. Tex-Tube Tex-Flow.
Qingdao V-Cart Piping Systems Co Ltd, JuiZhao Road, NanGuan Industry Zone, JiaoZhou City, Qingdao, China
Product Designation
Fitting Description
Remarks
7657, 3112, 57 mm, 2 108 57, 2, 76 32, 76, 3 42, 76, 3 13357, 2, 76, 3 576, 3 1412, 76, 3 15957, 76, 3, 108, 4 1652, 76, 3, 4 676, 3, 108, 4 876, 3, 108, 4
c, d c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d
20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90)
Product Designation
Fitting Description
Remarks
Figure 16T
a, b, c, d a, b, c
20 (90) 20 (90)
FM Approvals
1-303
Product Designation
Fitting Description
Remarks
7612, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2, 3 133114, 112, 2, 3 1391, 114, 112, 2, 3 1591, 114, 112, 2, 3, 4 1651, 114, 112, 2, 3, 4 62, 3, 4 8114, 112, 2, 3, 4
a, b, c, d a, b, c a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d
Product Designation
Fitting Description
Remarks
Figure 16T
a. b. c. d.
5712, 34, 1 212, 34, 1, 114, 112 7612, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2, 76, 3 133114, 112, 2, 76, 3 1391, 114, 112, 2, 76, 3 1591, 114, 112, 2, 76, 3, 4 1651, 114, 112, 2, 76, 3, 4 62, 76, 3, 4 8114, 112, 2, 76, 3, 4
a, b, c, d a, b, c a, b, c, d a, b, c a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d a, b, c, d
20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90) 20 (90)
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with GB/T 3091-93 or GB/T 8163-99 Pipe.
SCE Company Ltd, Unit E&F, 20/F., CDW Building, 388 Castl Peak Road, Tsuen Wan, N.T., Hong Kong
Product Designation Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Remarks
AQUILA Model 3G
AQUILA Model 3J
AQUILA Model 4G
212114, 112 3114, 112, 2 14, 112, 2, 212, 3 41 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4
a, c
300 (2070)
a, b, c
300 (2070)
a, c
300 (2070)
FM Approvals
1-304
Product Designation
Pipe Ends
Remarks
AQUILA Model 4J
212114,
112
a, b, c
3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4 212114, 112 3114, 112, 2 4114, 112, 2, 212, 3 5114, 112, 2, 212, 3 6114, 112, 2, 212, 3, 4
300 (2070)
a, b, c
300 (2070)
Remarks: a. For use on Schedule 10 and heavier steel sprinkler pipe. b. Approved when supplied with NPT female threads. c. Approved when supplied with EPDM gasket.
SPT Metal Corp, 19-1 Da Yeh St, Da Liao Hsiang, Kaohsiung Hsien, Taiwan ROC
Mechanical Tee Branch Outlet. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
Remarks
520 Tee
21, 2114, 2112 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112 42, 4212, 43, 5112, 6114, 61-1/2, 62, 6212, 63, 64, 8212, 83, 84 2114, 2112 212114, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 4212, 43
a, b, c
300 (2070)
520 Tee
212112,
c, e, f, g, h, i, j
300 (2070)
Mechanical Tee Branch Outlet. Grooved outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
522 Tee
3112, 32 4112, 2, 212, 3 6112, 2, 212, 3, 4 8212, 3, 4 3112, 2 41, 112, 2, 212, 3
a, b, c
522 Tee
c, f, g, h, j
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. c. With EPDM gasket. e. When joining Allied Tube & Conduit XL threadable Thinwall pipe, 1-2 in. only. f. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. g. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. i. For use with Central Sprinkler TL threadable Thinwall pipe. j. For use with Bull Moose Tube EDDY-Flow pipe. m. For use with Wheatland Mega-Flow non-threadable Thinwall pipe.
Shanghai Recomb Piping System Co Ltd, No. 270 Yixian Rd, Shanghai, 200434 P. R. China
Product Designation Pipe Actual Size mm Fitting Description Remarks Max Working Pressure, psi (kPa)
XGQT3
60G12, 60G34, 60G1,60G114, 60G112, 73G12, 73G34, 73G1, 73G114, 73G112, 73G2, 76G12, 76G34, 76G1, 76G114, 76G112, 89G2 89G12, 89G34, 89G1, 89G114, 89G112, 108G1,108G114, 108G112, 108G2, 108G212, 114G12, 114G34, 114G1, 114G114, 114G112, 114G2, 114G212, 114G212A, 114G3, 133G1, 133G114, 133G112, 133G2, 133G212, 133G3, 140G1, 140G114, 140G112, 140G2, 140G212, 140G3, 159G1, 159G114, 159G112, 159G2, 159G212, 159G3, 165G1, 165G114, 165G112, 165G2, 165G212, 165G3, 168G12, 168G34,168G1, 168G114,168G112, 168G2, 168G212, 168G212A, 168G3, 219G1, 219G114, 219G112, 219G2, 219G212, 219G212A, 219G3, 273G2, 273G212 273G3, 5G34, 5G1, 5G114, 5G112, 5G2, 5G212, 5G212A, 5G3
a, b, c
300 (2070)
FM Approvals
1-305
Product Designation
Fitting Description
Remarks
XGQT3
6042, 6048, 7342, 7348, 7360, 7642, 7648, 8942, 8948, 8960, 10860, 10876, 11442, 11448, 11460, 11473, 11476, 11489, 13360, 13376, 13389, 14060, 14076, 14089, 15960, 15976, 15989, 159108, 159114, 16542, 16548, 16560, 16576, 16589, 165114, 16842, 16848, 16860, 16873, 16876, 16889, 168108, 168114, 21960, 21973, 21976, 21989, 219108 219114, 5114, 5112, 52, 5212A, 53 27360, 27376, 27389, 273108 and 273114
a, b, c
300 (2070)
XGQT3
a, b, c
XGQT3U
42G12, 42G34, 42G1, 48G12, 48G34, 48G1, 60G12, 60G34, 60G1, 73G12, 73G34, 73G1, 76G12, 76G34, 76G1 33G12, 42G12, 42G34, 42G1, 48G12, 48G34, 48G1, 60G12, 60G34, 60G1, 73G12, 73G34, 73G1, 76G12, 76G34, 76G1
a, b, c
XGQT3D
a, b, c
235 (1620)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Rated Pressure, psi (kPa)
7721
7722
723 Saddle-Let
73 Mini-Saddle
212, 234, 21, 2114, 2112, 21212, 21234, 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 4212, 43, 5x2, 5x212 6114, 6112, 62, 6212, 63, 64, 8x2, 8x212, 8x3, 8x4 3112, 32, 4112, 42, 4212, 43, 5x2, 5x212 6112, 62, 6212, 63, 64, 8x2, 8x212, 8x3, 8x4 114, 12, 34, 1 112, 12, 34, 1 2, 12, 34, 1 212, 12, 34, 1 11438, 11412, 11434, 11238, 11212, 11234, 21212, 234 114 x 12, 114 x 34, 114 x 1, 112 x 2, 112 x 34, 112 x 1, 2 x 12, 2 x 34, 2x1
300 (2070)
a, b
300 (2070)
Mechanical Branch Outlet Female NPT Mechanical Branch Outlet Female NPT
a, b
300 (2070)
a, b
300 (2070)
a, b
300 (2070)
a. For use on Schedule 10 or heavier pipe. NPT internal thread outlet. Clamps over pre-drilled hole in pipe wall. b. The Model 723 Mechanical Tee may be used with Schedule 10 and heavier, plus: Model Sizes, in.
Allied XL, Allied Super-Flow Allied BLT Allied Dyna-Flow Bull Moose EDDY-Lite Central TL Wheatland WLS
FM Approvals
1-306
Product Designation
Type of Outlet*
11212, 11234, 1121, 212, 234, 21, 21 21212, 1234, 2 2121, 212114, 212112, 334, 31, 31, 3112, 434, 41, 4112, 42, 61, 6112, 6112, 62
300 (2070)
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max. Working Pressure psi (kPa)
MT1
MT1
MT2
MT2 MT-3
MT-3
MT-8
21, 114, 112 2121, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 21, 114, 112 2121, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 212, 3 5112, 2, 212 6114, 112, 2, 212, 3, 4 3112, 2 4112, 2, 3, 76 mm 52, 212, 3 6112, 2, 212, 3, 4, 76 mm 3112, 2 4112, 2, 3, 76 mm 11412, 34, 1 11212, 34, 1 212, 34, 1 21212, 34, 1 11412, 34, 1 11212, 34, 1 212, 34, 1 21212, 34, 1 21, 114, 112 31, 114, 112, 2 41, 114, 112, 2, 76 mm 676 mm 21, 114, 112 76 mm1, 114, 112 16576 mm
Mechanical Tee, Threaded Outlet (Female NPT) Mechanical Tee, Threaded Outlet (Female NPT)
k, l
175 (1205)
a, c, g, i, m, n, p, q, r, s
300 (2070)
a, c, s
300 (2070)
l a, c, g, h, m, n, q, r, s
NPT Internal
e, k, l
175 (1205)
Mechanical Tee Threaded Outlet (BSP Threads) Mechanical Tee Threaded Outlet (BSP Threads) Mechanical Tee Threaded Outlet (BSP Threads)
a, b, c, i, m, n, q, s
300 (2070)
Remarks: a. For use with FM Approved Schedule 10 and 40 steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, 3, 4, 5, 6, and 8 in. NPS. b. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. c. For use with Allied Tube and Conduit XL and XL-II threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, and 3 in. NPS. d. For use with Sawhill Tubular SLS threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. e. For use with Wheatland Tube WST Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. f. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3, 4, and 6 in. NPS. g. For use with AMS Tube Steady-Flow Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3. h. For use with Wheatland Tube Mega Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. i. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 4 and 6 in. NPS. j. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. k. For use with Bull Moose Tube Ultra - EDDY Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. l. For use with Bull Moose EDDY Flow Lightwall steel sprinkler pipe in sizes: 2, 2 12, 3, and 4 in. NPS. m. For use with Allied Tube and Conduit BLT threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. n. For use with Bull Moose Tube EDDY-Lite threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. p. For use with Western International Forest Products Rapid-Thread steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. q. For use with Wheatland Tube WLS threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. r. For use with Western International Forest Products Fire Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 3, and 4 in. NPS. s. For use with Allied Tube and Conduit Dyna Flow and Super-Flo Lightwall sprinkler pipe in sizes: 112, 2, 2 12, 3, 4, and 6 in. NPS. t. For use with BS 1387 Medium or Heavy steel pipe.
Grinnell Clamp-T. For use with Schedule 10S or heavier pipe*, in 6 in. or smaller sizes and 0.188 in. (5 mm) wall or heavier pipe, in the 8 in. size. With EPDM gasket (green stripe) only.
*Pressure ratings vary by size:
FM Approvals
1-307
212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 4114, 112, 2, 212; 8212, 3 3114, 112, 2; 43; 5114, 112, 2, 212, 3; 14, 112, 2, 212, 3 61 312, 34, 1; 412, 34, 1; 64; 84
400 (2760)
350 (2415)
300 (2070)
Product Designation
Fitting Description
Grinnell 7044
Grinnell 7045
11412, 34, 1 11212, 34, 1 212, 34, 1 21212, 34, 1 212, 34, 1, 114, 112 21212, 34, 1, 114, 112 Not Applicable 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2 Not Applicable 4212, 3 Not Applicable 5114, 112, 2, 212, 3 Not Applicable Not Applicable 6114, 112, 2, 212 Not Applicable 63, 4 8212, 3, 4 Not Applicable 212, 234, 21, 14, 2112, 21212, 21 21234, 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 4212, 43, 6114, 6112, 62, 6212, 63, 64
Grinnell 7045
Grinnell 7045T
60.321.3, 26.7, 33.4, 42.4, 48.3 73.021.3, 26.7, 33.4, 42.4, 48.3 76.121.3, 26.7, 33.4, 42.4, 48.3 88.921.3, 26.7, 33.4, 42.4, 48.3, 60.3 114.321.3, 26.7, 33.4, 42.4, 48.3, 60.3 114.376.1 114.373.0, 88.9 139.742.4, 48.3, 60.3, 73.0, 76.1, 88.9 141.342.4, 48.3, 60.3, 73.0, 88.9 141.376.1 165.142.4, 48.3, 60.3, 73.0, 76.1, 88.9, 114.3 168.342.4, 48.3, 60.3, 73.0 168.376.1 168.388.9, 114.3 219.173.0, 88.9, 114.3 219.176.1 175 (1205)
FM Approved with ANSI NPT thread or ISO thread as appropriate for the outlet pipe.
Grinnell 7046 Clamp-T With Grooved Outlet 2114, 112 212114, 112 Not Applicable 3114, 112, 2 4114, 112, 2, 212 Not Applicable 43 Not Applicable 5114, 112, 2, 212, 3 Not Applicable 6114, 112, 2, 212 Not Applicable 63, 4 8212, 3, 4 60.342.4, 48.3 73.042.4, 48.3 76.142.4, 48.3 88.942.4, 48.3, 60.3 114.342.4, 48.3, 60.3, 73.0 114.376.1 114.388.9139.742.4, 48.3, 60.3, 73.0, 88.9 141.342.4, 48.3, 60.3, 73.0, 88.9 165.142.4, 48.3, 60.3, 73.0, 76.1, 88.9, 114.3 168.342.4, 48.3, 60.3, 73.0 168.376.1 168.388.9, 114.3 219.173.0, 88.9, 114.3
FM Approvals
1-308
Product Designation
Fitting Description
Grinnell 7046T
3112, 32, 4112, 42, 4212, 43, 6112, 62, 6212, 63, 64
175 (1205)
Product Designation
Fitting Description
Grinnell 7047
212 3 4
114, 112 Not Applicable 114, 112, 2 114, 112, 2, 212 Not Applicable 3 Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable 3, 4 2, 212, 3, 4 Not Applicable
73.0 76.1 88.9 114.3 114.3 114.3 139.7 139.7 141.3 141.3 165.1 165.1 168.3 168.3 168.3 219.1 219.1
Fitting Description
6 8
42.4, 48.3 42.4, 48.3 42.4, 48.3, 60.3 42.4, 48.3, 60.3, 73.0 76.1 88.9 42.4, 48.3, 60.3, 73.0 76.1 42.4, 48.3, 60.3, 73.0 76.1 42.4, 48.3, 60.3, 73.0 76.1, 88.9, 114.3 42.4, 48.3, 60.3, 73.0 76.1 88.9, 114.3 60.3, 73.0, 88.9, 114.3 76.1
Nominal Pipe Size, in.
Product Designation
Grinnell 7048
212 3 4
112 Not Applicable 114, 112, 2 114, 112, 2, 212 Not Applicable 3 Not Applicable 114, 112, 2, 212 Not Applicable Not Applicable 114, 112, 2, 212 Not Applicable 3, 4 212, 3, 4
73.0 76.1 88.9 114.3 114.3 114.3 139.7 141.3 165.1 165.1 168.3 168.3 168.3 219.1
Fitting Description
6 8
Product Designation
48.3 42.4, 48.3 42.4, 48.3, 60.3 42.4, 48.3, 60.3, 73.0 76.1 88.9 42.4, 48.3, 60.3, 73.0 42.4, 48.3, 60.3, 73.0 42.4, 48.3, 60.3, 73.0 76.1, 88.9, 114.3 42.4, 48.3, 60.3, 73.0 76.1 88.9, 114.3 73.0, 88.9, 114.3
Nominal Pipe Size, in.
Grinnell 7049
Sizes of the Figure 7049 Clamp Tee Crosses can be formed with any combination of the sizes shown of Figure 7047 or 7048 Clamp Tee Crosses having the same run size.
FM Approvals
1-309
Allied Tube & Conduit Super-Flo, 2 in. and Allied Tube & Conduit Dyna-Flow, 2 in. 175 psi (1205 kPa). Allied Tube & Conduit Super-Flo, 212-4 in. and Allied Tube & Conduit Dyna-Flow, 212-3 in. 300 psi (2070 kPa). Tex-Tube Co. Tex-Flow. 3-8 in. 300 psi (2070 kPa). Except 2 in. run sized items and 21212, 34, 1 in. sized branch connections.
Mechanical Tee or Cross Branch Outlet. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max. Working Pressure psi (kPa)
1 12, 34 1 1 4 1 1 2
38, 34, 12, 34,
1 1
a, b, c, d, e, g, j, l, n, p, q, r, s, t, v 1 c, m c, f, h, k, u a, b, c, d, e, g, j, m, n, p, q, r, s, t, v c, m
2 212
12, 34,
1 1
12, 34,
76 mm
12, 34,
1-2 Grinnell Figure 522 Tee or Cross Mechanical Branch Outlet (ISO 7-1) 1
12, 34
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070)
114 38, 12, 34, 1 112 12, 34, 1 2 12, 34, 1 212 12, 34, 1 76 mm 12, 34, 1
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a. Min schedule cut groove pipe: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 m) wall. c. With EPDM gasket (green stripe) Grade E or (purple stripe) Grade A. d. Min schedule pipe: 3 in. or smaller Allied Tube & Conduit Corp Approved BLT, XL, XL-II, Super- XL and Super-40 Thinwall pipe. e. Min schedule pipe: Allied Tube Dyna-Flow and Super-flo Lightwall pipe, 300 psi (2070 kPa). f. IDOD Gal-5 and All-Gal pipe, 114 to 2 in. sizes, 175 psi (1205 kPa). g. IDOD Gal-7 and Gal-Flo pipe, 114 to 2 in. sizes. h. Allied Tube Dyna-Light pipe, 1 to 2 in. sizes, 175 psi (1205 kPa). j. Bull Moose EDDY-Lite pipe, 1-2 in. sizes. k. Bull Moose Ultra-EDDY pipe at 175 psi (1205 kPa), 1-2 in. sizes. l. Bull Moose EDDY-Flo pipe, 175 psi (1205 kPa). m. BS 1487 pipe, medium and heavy wall at 300 psi (2070 kPa), and ISO 4200 pipe. n. For use with Welded TubeBerkeley LLC Steady-Flow pipe. p. WIFP Fire Line Flow & Rapid-Thread Light Pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS and SL threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT and GL threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe at 175 psi (1205 kPa). v. Youngstown Tube Fire-Flo and EZ-Thread Pipe.
Mechanical Tee or Cross Branch Outlet. NPT internal outlet connection or grooved outlet. Clamps over hole in pipe wall. 730 Tee or Cross Mechanical Branch Outlet (FNPT) 212, 34, 1, 114, 112 21212, 34, 1, 114, 112, 2 312, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2, 212, 3 4 5112, 2, 212, 3 6114, 6112, 2, 212, 3, 4 82, 212, 3, 4 1 1 4, a, b, c, d, e, f, I, j, k, l, n, o, p, q, r, s, t, u a, b, c, d, e, f, l, n, o, p, q, r, s 300 (2070) 300 (2070)
a, b, c, e, l, p, q, r a, b, c, l c, n
412, 34, 1, 114, 112, 2, 212, 3 6114, 6112, 2, 212, 3, 4 76 mm by 12, 34, 1, 114, 112, 2 139 mm 112, 3 165 mm by 114, 112, 2, 76 mm c, n a, b, c, m a, b, c, e, f, l, m, q, v 175 (1205) 300 (2070) 300 (2070)
FM Approvals
1-310
Product Designation
Fitting Description
Remarks
2112 212112 3112, 2 76 mm112 4112, 2, 212, 3, 76 mm 6114, 112, 2, 212, 3, 4, 76 mm 2112 2112 2112 212112 3112, 2 76 mm112 4112, 2, 212, 3, 76 mm 82, 212, 3, 4, 76 mm
e, i, m, n, o, p, q, r
300 (2070)
b, k t, u b, s
e, m, p, q, r
300 (2070)
Mechanical Tee Branch Outlet. BSP internal outlet connection or grooved outlet. Clamps over hole in pipe wall. 730 Tee or Cross Mechanical Branch Outlet (BSP) 212, 34, 1, 114, 112 212, 34, 1, 114, 112 21212, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 76 mm12, 34, 1, 114, 112 412, 34, 1, 114, 112, 2 21212, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2, 3 5112, 2, 3, 76 mm 6114, 112, 2, 212, 3, 4, 76 mm 82, 3, 4, 76 mm i, n, o, p, q, r, s, t b, k m, n, o, p, q, r 300 (2070) 175 (1205) 300 (2070)
b, s
300 (2070)
m, p, q, r
300 (2070)
a. For use with Allied Tube & Conduit Dyna-Light Schedule 5 Lightwall pipe. b. For use with Allied Tube & Conduit Dyna-Flow and Super-Flo non-threadable Lightwall pipe. c. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. d. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. e. For use with Central 7 non-threadable Lightwall pipe. f. For use with Central Sprinkler TL threadable Thinwall pipe. g. For use with Schedule 10S or heavier steel sprinkler pipe. h. Mechanical fittings with NPT internal outlet connections to clamp over 1 in. (25 mm) drilled hole. i. For use with Central Sprinkler TL threadable Thinwall steel sprinkler pipe. j. Branch line sprinkler installation 1 in. outlet size only. k. For use with Bull Moose Ultra-EDDY Schedule 5 Lightwall steel sprinkler pipe. m. For use with BS 1387 pipe, medium and heavy wall steel sprinkler pipe. n. For use with Allied Tube & Conduit XL and Super-XL threadable Thinwall steel sprinkler pipe. o. For use with Allied Tube & Conduit Super-40 threadable Thinwall steel sprinkler pipe. p. Min schedule cut groove pipe: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. q. Min schedule rolled groove pipe: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 m) wall. r. With EPDM gasket (green stripe). s. For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. t. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. u. For use with IDODs Gal-7 and Gal-Flo pipe. v. For use with ISO 4200 steel sprinkler pipe.
Grinnell Figure 40-5 Mechanical Outlet Tee. 114, 112, 2 and 212 in. plus 76 mm nominal run size, each with 12, 34 or 1 in. NPT outlets. Approved for use with Schedule 5, 10 and 40 pipe. Also, Allied Dyna-Flow and Dyna-Thread, Allied Super-Flo and XL, Central Grooved Piping Products TL, Bull-Moose EDDY-Lite and Wheatland WLS, MLT, WST and MEGA-flow Steel Sprinkler Pipes. Approved for use with Central Grooved Piping Products Central 7 and Welded TubeBerkeley LLC Steady-flow pipes. Approved for use with Youngstown Fire-flo and EZ-Thread pipe. Grinnell Figure 40-5 Mechanical Outlet Tee. 114, 112, 2 and 212 in. nominal run size, each with 12, 34 or 1 in. BSP outlets. Approved for use with the following run pipes: Schedules 5, 10 and 40 pipe. Allied Dyna-Flow and Dyna-Thread, Allied Super-Flow and XL, Central Sprinkler TL, Bull-Moose EDDY-Lite and Wheatland WLS, MLT, WST and MEGA-flow Steel Sprinkler Pipes. Approved for use with Youngstown Fire-flo and EZ-Thread pipe. Approved for use with IDODs Gal-7 and Gal-Flo pipe. Style 300 Ease-Tee. Mechanical fittings with NPT internal outlet connections for use with Schedule 40 pipe to clamp over 1 in. (25 mm) drilled hole. 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
300
FM Approvals
1-311
Product Designation
Fitting Description
21212, 34, 1
Mek-Tee Mechanical Tee or Cross Branch Outlet. For use on Schedule 10 or heavier pipe. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
Remarks
300
Ease-Tee
112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1; 21212, 34, 1
300 (2070)
Mechanical Tee or Cross Branch Outlet. NPT internal outlet connection. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
Remarks
522 Tee
a, b, c, d, e, g, j, k, n, p, q, r, s, t, v c, m c, f, h, l, u a, b, c, d, e, g, j, n, p, q, r, s, t, v 1 c, m
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
112, 34 11438, 12, 34, 11212, 34, 1 212, 34, 1 21212, 34, 1 76 mm12, 34, 1
a. Min schedule cut groove pipe: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 m) wall. c. With EPDM gasket (green stripe) Grade E or (purple stripe) Grade A. d. Min schedule pipe: 3 in. or smaller Allied Tube & Conduit Corp FM Approved BLT, XL, XL-II, Super-XL and Super-40 Thinwall pipe. e. Min schedule pipe: Allied Tube Dyna-Flow and Super-flo Lightwall pipe, 300 psi (2070 kPa). f. IDOD Gal-5 and All-Gal pipe, 114 to 2 in. sizes, 175 psi (1205 kPa). g. IDOD Gal-7 and Gal-Flo pipe, 114 to 2 in. sizes. h. Allied Tube Dyna-Light pipe, 1 to 2 in. sizes, 175 psi (1205 kPa). j. Bull Moose EDDY-Lite pipe, 1-2 in. sizes. k. Bull Moose Ultra-EDDY pipe at 175 psi (1205 kPa), 1-2 in. sizes. l. Bull Moose EDDY-Flo pipe, 175 psi (1205 kPa). m. BS 1387 pipe, medium and heavy wall at 300 psi (2070 kPa), and ISO 4200 pipe. n. For use with Welded TubeBerkeley LLC Steady-Flow pipe. p. WIFP Fire Line Flow & Rapid-Thread Light Pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS and SL threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT and GL threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe at 175 psi (1205 kPa). v. Youngstown Tube Fire-Flo and EZ-Thread Pipe.
Mechanical Tee or Cross Branch Outlet. NPT internal outlet connection or grooved outlet. Clamps over hole in pipe wall.
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
Remarks
212, 34, 1, 114, 112 212x12, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2, 212, 3 5112, 2, 212, 3
a, b, c, d, e, f, j, k, l q, r, s, t a, b, c, d, e, f, l, q
FM Approvals
1-312
Product Designation
Fitting Description
Remarks
6114, 6112, 2, 212, 3, 4 82, 212, 3, 4 730 Tee or Cross FNPT 312, 34, 1, 114, 1 1 2, 2 412, 34, 1, 114, 112, 2, 212, 3 6114, 6112, 2, 212, 3, 4 76 mm by 12, 34, 1, 114, 112, 2 165 mm by 114, 112, 2, 76 mm 212, 34, 1, 114, 112 212, 34, 1, 114, 112 212x12, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2, 212, 4
a, b, c, l a, b, c, l c, n
c, n a, b, c, m a, b, c, m e, i, n, o, p, q, r, s, t, u b, k e, n, o, p, q, r
175 (1205) 300 (2070) 300 (2070) 300 (2070) 175 (1205) 300 (2070)
3 5112, 2, 212, 3 212x12, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 412, 34, 1, 114, 112, 2, 212, 3 6114, 6112, 2, 212, 3, 4 82, 730 Tee or Cross Mechanical Branch Outlet (Grooved) 212, 3, 4
b, s
300 (2070)
e, p, q, r e, p, q, r e, i, m, n, o, p, q, r
2112 212112 3112, 2 76 mm112 12, 2, 212, 3, 76 mm 41 6114, 112, 2, 212, 3, 4, 76 mm 2x112 2x112 2112 212112 3112, 2 76 mm112 4112, 2, 212, 3, 76 mm 82, 212, 3, 4, 76 mm 212 by 2 139 mm by 112, 3
b, k t, u b, s
e, m, p, q, r a, b, c, d, e, f, l, q m, v
Mechanical Tee Branch Outlet. BSP internal outlet connection or grooved outlet. Clamps over hole in pipe wall.
730 Tee or Cross Mechanical Branch Outlet (BSP) 212, 34, 1, 114, 112 212, 34, 1, 114, 112 212x12, 34, 1, 114, 112 312, 34, 1, 114, 112, 2 76 mm12, 34, 1, 114, 112 412, 34, 1, 114, 112, 2 212x12, 34, 1, 114, 112 312, 34, 1, 114, 1 1 2, 2 412, 34, 1, 114, 112, 2, 3 5112, 2, 3, 76 mm 14, 112, 2, 212, 3, 4, 61 76 mm 82, 3, 4, 76 mm
a. b. c. d. g. h. j. k. For use with Allied Tube & Conduit Dyna-Light Schedule 5 Lightwall pipe. For use with Allied Tube & Conduit Dyna-Flow and Super-Flo non-threadable Lightwall pipe. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. For use with Schedule 10S or heavier steel sprinkler pipe. Mechanical fittings with NPT internal outlet connections to clamp over 1 in. (25 mm) drilled hole. Branch line sprinkler installation 1 in. outlet size only. For use with Bull Moose Ultra-EDDY Schedule 5 Lightwall steel sprinkler pipe.
i, n, o, p, q, r, s, t b, k m, n, o, p, q, r
b, s
300 (2070)
m, p, q, r
300 (2070)
FM Approvals
1-313
m. For use with BS 1387 pipe, medium and heavy wall steel sprinkler pipe. n. For use with Allied Tube & Conduit XL and Super-XL threadable Thinwall steel sprinkler pipe. o. For use with Allied Tube & Conduit Super-40 threadable Thinwall steel sprinkler pipe. p. Min schedule cut groove pipe: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. q. Min schedule rolled groove pipe: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 m) wall. r. With EPDM gasket (green stripe). s. For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. t. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. u. For use with IDODs Gal-7 and Gal-Flo pipe. v. For use with ISO 4200 steel sprinkler pipe.
Model 40-5 Mechanical Outlet Tee. 114, 112, 2 and 212 in. plus 76 mm nominal run size, each with 12, 34 or 1 in. NPT outlets. FM Approved for use with Schedule 5, 10 and 40 pipe. Also, Allied Dyna-Flow and Dyna-Thread, Allied Super-Flo and XL, Central Grooved Piping Products TL, Bull-Moose EDDY-Lite and Wheatland WLS, MLT, WST and MEGA-flow Steel Sprinkler Pipes. FM Approved for use with Central Grooved Piping Products Central 7, and Welded TubeBerkeley LLC Steady-Flow pipes. FM Approved for use with Youngstown Fire-flo and EZ-Thread pipe. Model 40-5 Mechanical Outlet Tee. 114, 112, 2 and 212 in. nominal run size, each with 12, 34 or 1 in. BSP outlets. FM Approved for use with the following run pipes: Schedules 5, 10 and 40 pipe. Allied Dyna-Flow and Dyna-Thread, Allied Super-Flow and XL, Central Sprinkler TL, Bull-Moose EDDY-Lite and Wheatland WLS, MLT, WST and MEGA-flow Steel Sprinkler Pipes. FM Approved for use with Youngstown Fire-flo and EZ-Thread pipe. FM Approved for use with IDODs Gal-7 and Gal-Flo pipe.
073
Mechanical Branch Outlet (FNPT) Mechanical Branch Outlet (Grooved Outlet) Mechanical Branch Outlet (Grooved Outlet) Mechanical Branch Outlet (FNPT or ISO or BSP) Mechanical Branch Outlet (FNPT) Mechanical Branch Outlet (Grooved Outlet) Mechanical Branch Outlet (Grooved Outlet) Mechanical Branch Outlet (Grooved Outlet)
21234
c, d, e, f, g, h, i, j
175 (1205) 300 (2070) 300 (2070) 400 (2760) 300 (2070) 300 (2070) 300 (2070)
920
4212, 3
c, k
920
920
920
64, 3
c, m
920
64, 3
c, m
920N
21, 114, 112 2121, 114, 1 1 2, 2 31, 114, 112, 2 212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1, 114, 112, 2; 412, 34, 1, 114, 112, 2; 62, 114 2114, 112; 212114, 112 3114, 112, 2; 4114, 112, 2; 62, 114
c, k, l
920N
c, k
300 (2070)
920N
c, m
300 (2070)
920N
c, m
300 (2070)
a. Use limited to a min of Schedule 10S pipe in 6 in. or smaller sizes and 0.188 in. (5 mm) wall pipe in 8 in. or larger sizes. b. For use with Schedule 40 pipe in 6 in. or smaller, and Schedule 30 pipe for 8 in. NPS steel sprinkler pipe. c. With gasket E (green stripe), H (white stripe) or L (solid red). d. For use with Allied Tube XL, Super-XL and Super-40 threadable Thinwall pipe. e. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. f. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. g. For use with Allied Tube & Conduit Super-Flo or Dyna-Flow non-threadable Lightwall pipe. h. For use with Central Sprinkler TL threadable Thinwall steel sprinkler pipe. i. For use with Bull Moose Ultra-EDDY non-threadable Lightwall steel sprinkler pipe. j. For use with Bull Moose EDDY-Flow non-threadable Lightwall steel sprinkler pipe. k. For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. l. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. m. For use with Wheatland Tube Mega Flow non-threadable Lightwall steel sprinkler pipe.
Style 920 Mechanical-T Branch Outlet or Cross. For working pressures up to 400 psi (2760 kPa). Branch is available with either grooved or NPT internal connection, except as noted. Use limited to a min of Schedule 10S pipe in 6 in. or smaller sizes and 0.188 in. (5 mm) wall pipe in 8 in. or larger sizes. 63, 4 and 83, 4 in. sizes are limited to a pressure rating of 250 psi (1725 kPa) when used with Schedule 10S pipe, and limited to pressure rating of 300 psi (2070 kPa) for 63, 4 on Schedule 40, and for 83, 4 on Schedule 30. Limited to pressure rating
FM Approvals
1-314
of 300 psi (2070 kPa) up to and including 43 on Allied Tube & Conduit Dyna-Flow Lightwall pipe. For use with Northwest EZ-Flow 4 and 6 in. non-threadable Lightwall pipe. For use with Central Sprinkler TL pipe in 1-2 in. sizes. For use with Wheatland MLT up to 2 in. nominal size. For use with Central 7 pipe in 112-4 in. sizes. For use with Western Fire-Flow pipe.
Product Designation Nominal Outlet Size, in. Nominal Pipe Size, in.
920
31*, 114*, 112, 2*; 41*, 114*, 112*, 2, 212, 3; 5112, 2, 212, 3; 6114, 112, 2, 212, 3, 4; 8212, 3, 4; 76 mm1, 114, 112 NPT 76 mm112 BSP
*Threaded branch only. 300 psi (2070 kPa) on Allied Tube & Conduit Dyna-Flow Lightwall sprinkler pipe.
Style 920 Mechanical-T Branch Outlet or Cross. For working pressures up to 175 psi (1205 kPa). Branch is provided with a British Standard internal taper pipe thread. Run pipes must be Schedule 10 or heavier wall in sizes up to 6 in. and 0.188 in. (4.8 mm) min wall in larger sizes. Branch pipes must be Schedule 40 or heavier.
920 Mechanical Branch Outlet or Cross 31, 114, 112, 2; 41, 114, 112, 2, 212, 3; **6112, 2, 212, 3, 4; 6.5*112, 2, 212, 3, 4; 82, 212, 4 76 mm1
*For use on British Standard outside dia. pipe. **Tex-Tube Co. Tex-Flow non-threadable Lightwall pipe. 6 in. size.
Style 920N Mechanical-T Branch Outlet or Cross. For working pressure up to 400 psi (2760 kPa). Branch is available with NPT female outlet connection. Use limited to Schedule 10 and 40 pipe in 6 in. or smaller sizes at 400 psi (2760 kPa). For working pressure up to 300 psi (2070 kPa) on Super-Flo, Dyna-Flow, Super XL, Super 40, XL, BLT, TL, Gal-flo and Gal-7, EZ-Flow and EDDY-Flow.
920N Mechanical Branch Outlet or Cross NPT Outlet 212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1, 114, 112, 2; 412, 34, 1, 114, 112, 2; 6112, 2
Style 920N Mechanical-T Branch Outlet or Cross. For working pressure up to 400 psi (2760 kPa). Branch is available with BSP female outlet connection. Use limited to BS 1387 Medium or Heavy run pipe, or DIN 2458, or ISO 4200 run pipe. 920N Mechanical Branch Outlet or Cross BSP Outlet 76 mm by 114, 112
Use limited to Schedule 10 and 40 pipe at 400 psi (2760 kPa). Use limited to BS 1387 Medium or Heavy Run Pipe, or Din 2458, or ISO 4200 pipe.
Style 920N Mechanical-T Branch Outlet or Cross. For working pressure up to 400 psi (2760 kPa). Branch is available with grooved outlet connection. Use limited to Schedule 10 and 40 pipe in 6 in. or smaller sizes at 400 psi (2760 kPa). For working pressure up to 300 psi (2070 kPa) on Super-Flo, Dyna-Flow, Super XL, Super 40, XL, BLT, TL, EZ-Flow and EDDY-Flow.
920N Mechanical Branch Outlet or Cross Grooved Outlet 2114, 112; 212114, 112; 3114, 112, 2; 4114, 112, 2; 6114, 112, 2
Style 921 Mechanical-T Branch Outlet. For working pressures up to 300 psi (2070 kPa). NPT internal connection branch only. Use limited to a min of Schedule 10S pipe in 6 in. or smaller sizes and 0.188 in. (5 mm) wall pipe in 8 in. or larger sizes. 4 in. size is limited to a pressure rating of 250 psi (1725 kPa) when used with Schedule 10S pipe. For working pressure up to 300 psi (2070 kPa) up to and including 4 1 size on Allied Tube & Conduit Dyna-Flow Lightwall pipe. For use with Northwest EZ-Flow 4 in. non-threadable Lightwall pipe. For use with Wheatland MLT up to 2 in. nominal size and Mega-Flow up to 4 in. nominal size. For use with Central 7 pipe in 112-4 in. sizes. For use with Western Fire-Flow and Fire-Thread pipe. For use with Yieh Phui SPS Flow Pipe, 114 through 4 in. NPS.
921 Mechanical Branch Outlet 212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1; 412, 34, 1
300 psi (2070 kPa) on Allied Tube & Conduit Dyna-Flow Lightwall sprinkler pipe and Tex-Tube Tex-Flow pipe.
Style 921 Mechanical-T Branch Outlet. For working pressures up to 175 psi (1205 kPa). British Standard internal taper pipe thread branch connections only. Run pipe must be Schedule 10 or heavier. Branch pipe must be Schedule 40, or heavier.
921 Mechanical Branch Outlet 212, 34, 1, 112; 212112; 312, 34, 1; 41
FM Approvals
1-315
Product Designation
Style 922 Sprinkler Outlet, for use with Schedule 10 and 40 pipe in 114 through 212 in. NPS sizes. Also FM Approved for use with Allied XL and Dyna-flow, Bull Moose Ultra-EDDY and EDDY-flow, Welded TubeBerkeley LLC Steady-Flow, Wheatland WLS, WST, and Mega-flow, IDOD Gal-5 and All-Gal. Clamps over hole in pipe wall. No gasket lubricant required.
922 Female NPT Sprinkler Outlet 11412, 34, 1; 11212, 34, 1; 212, 34, 1; 21212, 34, 1
Pressure rating 175 psi (1205 kPa) on Schedule 5 Pipe, 300 psi (2070 kPa) on all other heavier pipe schedules.
Style 925 Snaplet Sprinkler Outlet. For use on Allied Tube & Conduit Dyna-Flow, Schedule 5, 10 and 40 Sprinkler pipe. NPT internal outlet connection. Clamps over hole in pipe wall. Designed specifically for sprinkler heads. 1 outlet size may be used for branch connections. For use with Central Sprinkler TL pipe in 114-2 in. sizes; Allied Tube XL and Super-Flo pipes; Central 7 pipe in 112-212 in. sizes; and IDOD Systems Gal-5 pipe, and Bull Moose EDDY-Flow pipe and Wheatland Mega-Flow pipe.
925 Snaplet Sprinkler Outlet 11412, 34, 1; 11212, 34, 1; 212, 34, 1; 21212, 34, 1
Style 927 Sprinkler Outlet. For use on Schedule 10 and 40 Sprinkler pipe. DIN internal outlet connection. Clamps over hole in pipe wall. Designed specifically for sprinkler heads. 1 outlet size may be used for branch connections.
927 Sprinkler Outlet 11412, 34, 1 DIN; 11212, 34, 1 DIN; 212, 34, 1 DIN
21234
c. d. e. f. g. h. i. j.
NPT internal
c, d, e, f, g, h, i, j
175 (1205)
With gasket E (green stripe), H (white stripe) or L (solid red). For use with Allied Tube XL, Super-XL and Super-40 threadable Thinwall pipe. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. For use with Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. For use with Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. For use with Central Sprinkler TL threadable Thinwall pipe. For use with Bull Moose Ultra-EDDY non-threadable Lightwall pipe.
Style 920 Mechanical-T Branch Outlet or Cross. For working pressures up to 400 psi (2760 kPa). Branch is available with either grooved or NPT internal connection, except as noted. Use limited to a min of Schedule 10S pipe in 6 in. or smaller sizes and 0.188 in. (5 mm) wall pipe in 8 in. or larger sizes. 63, 4 and 83, 4 in. sizes are limited to a pressure rating of 250 psi (1725 kPa) when used with Schedule 10S pipe, and limited to pressure rating of 300 psi (2070 kPa) for 63, 4 on Schedule 40, and for 83, 4 on Schedule 30. Limited to pressure rating of 300 psi (2070 kPa) up to and including 4 x 3 on Allied Tube & Conduit Dyna-Flow Lightwall pipe. For use with Northwest EZ-Flow 4 in. non-threadable Lightwall pipe. For use with Central Sprinkler TL pipe in 1-2 in. sizes.
Product Designation Nominal Outlet Size, in. Nominal Pipe Size, in.
920
31*, 114*, 112, 2*; 41*, 114*, 112*, 2, 212, 3; 5112, 2, 212, 3; 6114, 112, 2, 212, 3, 4; 8212, 3, 4; 76 mm1, 114, 112 NPT 76 mm112 BSP
*Threaded branch only. 300 psi (2070 kPa) on Allied Tube & Conduit Dyna-Flow Lightwall sprinkler pipe.
Style 920 Mechanical-T Branch Outlet or Cross. For working pressures up to 175 psi (1205 kPa). Branch is provided with a British Standard internal taper pipe thread. Run pipes must be Schedule 10 or heavier wall in sizes up to 6 in. and 0.188 in. (4.8 mm) min wall in larger sizes. Branch pipes must be Schedule 40 or heavier.
920 Mechanical Branch Outlet or Cross 31, 114, 112, 2; 41, 114, 112, 2, 212, 3; 6112, 2, 212, 3, 4; 6.5*112, 2, 212, 3, 4; 82, 212, 4 76 mm1
Style 921 Mechanical-T Branch Outlet. For working pressures up to 300 psi (2070 kPa). NPT internal connection branch only. Use limited to a min of Schedule 10S pipe in 6 in. or smaller sizes and 0.188 in. (5 mm) wall pipe in 8 in. or larger sizes. 4 in. size is limited to a pressure rating of 250 psi (1725 kPa) when used with Schedule 10S pipe. For working pressure up to 300 psi (2070 kPa) up to and including 41 size on Allied Tube & Conduit Dyna-Flow Lightwall pipe. For use with Northwest EZ-Flow 4 in. non-threadable Lightwall pipe.
FM Approvals
1-316
Product Designation
921
212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1; 412, 34, 1
300 psi (2070 kPa) on Allied Tube & Conduit Dyna-Flow Lightwall sprinkler pipe.
Style 921 Mechanical-T Branch Outlet. For working pressures up to 175 psi (1205 kPa). British Standard internal taper pipe thread branch connections only. Run pipe must be Schedule 10 or heavier. Branch pipe must be Schedule 40, or heavier.
921
Style 922 Hooker Sprinkler Outlet. For use on Lightwall pipe, Schedule 10S, or heavier pipe. NPT internal outlet connection. Clamps over hole in pipe wall. Designed specifically for sprinkler heads. 1 outlet size may be used for branch connections.
922
Style 925 Snaplet Sprinkler Outlet. For use on Allied Tube & Conduit Dyna-Flow, Schedule 5, 10 and 40 Sprinkler pipe. NPT internal outlet connection. Clamps over hole in pipe wall. Designed specifically for sprinkler heads. 1 outlet size may be used for branch connections. For use with Central Sprinkler TL pipe in 114-2 in. sizes. For use with Allied Tube XL and Super-Flo pipes.
925
Style 927 Sprinkler Outlet. For use on Schedule 10 and 40 Sprinkler pipe. DIN internal outlet connection. Clamps over hole in pipe wall. Designed specifically for sprinkler heads. 1 outlet size may be used for branch connections.
927
Sprinkler Outlet
212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1, 114, 112, 2; 412, 34, 1, 114, 112; 42, 212, 3; 52, 212; 6114, 112, 2, 212, 3, 4; 8212, 3, 4; 212, 34, 1, 114, 112; 21212, 34, 1, 114, 112; 312, 34, 1, 114, 112, 2; 412, 34, 1, 114, 112, 2, 212, 3 7612, 34, 1, 114, 112; 476; 576; 1392, 212, 76; 676; 165114, 112, 2, 212, 76, 4; 876 mm
a, b, c
300 (2070)
c, e, f, h, j
300 (2070)
c, d
300 (2070)
Mechanical Tee Branch Outlet. Grooved outlet connection. Clamps over hole in pipe wall.
Uniking 2093 Tee Mechanical Branch Outlet (Grooved) 3114, 112, 2; 4114, 112, 2, 212, 3; 5212, 3; 6114, 112, 2, 212, 3, 4; 83, 4; a, b, c 300 (2070)
FM Approvals
1-317
Product Designation
Fitting Description
Remarks
3114,112, 2; 4114, 112, 2, 212, 3 476; 576; 139212, 76, 3; 676; 165114, 112, 2, 76, 3, 4; 876
a. b. c. d. e. f. h. j.
c, e, f, h, j
c, d
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with BS 1387 medium or heavy pipe. For use with Wheatland Mega-flow pipe. All FM Approved for use on Allied Tube & Conduit Dyna-Flow or Super-flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. For use with Bull Moose Tube EDDY-Flow pipe.
Virotec Rohrtechnik GmbH & Co KG, Meininger Weg 8, D-36132 Eiterfield, Germany
Model Virotec-T. Mechanical fittings with NPT internal outlet connections. For use with Schedule 10 or heavier pipe to clamp over 1 in. (25 mm) drilled hole. 175 psi (1205 kPa) pressure rating.
Product Designation Nominal Outlet Size, in. Nominal Pipe Size, in.
VT
138*, 12, 34, 1; 11438*, 12, 34,1; 11238*, 12, 34,1; 238*, 12, 34,1
5070
Weifang 100tong Co Ltd, No. 1919 Jinchang South Road, Weicheng District, Weifang, Shandong, PR China 261052
Product Designation Fitting Description Nominal Pipe Size, mm Rated Working Pressure, psi (kPa)
Remarks
GCQT3S
7633, 7642, 7648, 8933, 8942, 8948, 10833, 10842, 10848, 10860, 10876, 11433, 11442, 11448, 11460, 11476, 13333, 13342, 13348, 13360, 13376, 13389, 14033, 14042, 14048, 14060, 14076, 14089, 15933, 15942, 15948, 15960, 15976, 15989, 16533, 16542, 16548, 16560, 16576, 16589, 21933, 21942, 21948, 21960, 21976, 21989
230 (1600)
a, c a, c a, c a, c
FM Approvals
1-318
Outlet Connection
Remarks
Grooved, NPT external NPT internal Grooved, NPT external, NPT internal Grooved, NPT external NPT internal Grooved, NPT external NPT internal Grooved, NPT external, NPT internal NPT internal Grooved, NPT external
a, c a, c a, c a, c a, c a, c b, c b, c b, c b, c
500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 400 (2760) 400 (2760) 400 (2760) 400 (2760)
a. Max rated pressure limited to 300 psi (2070 kPa) when joining Schedule 10S rolled groove-ended pipe. b. Max rated pressure limited to 200 psi (1380 kPa) when joining Schedule 10S rolled groove-ended pipe. c. With gasket E (green stripe), H (white stripe) or L (solid red).
11212, 34, 1 212, 34 21 21212, 34, 212112 334 31 3112 434 41 4112 42 61, 112 62 1, 114
NPT internal Grooved, NPT external, NPT internal NPT internal Grooved, NPT external NPT internal Grooved, NPT external, NPT internal Grooved, NPT external NPT internal Grooved, NPT external NPT internal Grooved, NPT external, NPT internal NPT internal Grooved, NPT external
a, c a, c a, c a, c a, c a, c a, c a, c a, c a, c b, c b, c b, c b, c
500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 400 (2760) 400 (2760) 400 (2760) 400 (2760)
a. Max rated pressure limited to 300 psi (2070 kPa) when joining Schedule 10S rolled groove-ended pipe. b. Max rated pressure limited to 200 psi (1380 kPa) when joining Schedule 10S rolled groove-ended pipe. c. With gasket E (green stripe), H (white stripe) or L (solid red).
Weifang 100tong Co Ltd, No. 1919 Jinchang South Road, Weicheng District, Weifang, Shandong, PR China 261052
Product Designation Fitting Description Nominal Pipe Size, mm Rated Working Pressure, psi (kPa)
GCQT3
108x60, 108x76, 114x60, 114x76, 140x60, 140x76, 140x89, 159x76, 159x89, 159x108, 159x114, 165x60, 165x76, 165x89, 165x114, 219x57, 219x60, 219x76, 219x89, 219x114,
230 (1600)
FM Approvals
1-319
ATUSA empresarial SL, Aptd. Correos 8, Poligono Industrial Agurain S/N, 01200 Salvatierra, lava, Spain
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
a, b, c, d a, b, c, d
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. Approved when supplied with EPDM gasket. Approved when supplied with an ISO PN10 bolt pattern.
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Description Remarks Max Pressure Rating, psi (kPa)
7012
2, 212, 3, 4, 5, 6, 8, 10, 12 60, 76, 89, 114, 139, 165, 168, 219, 273 and 324 mm 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4 5, 6, 8, 10, 12 5, 6, 8, 10, 12
Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, d, e, f, g, h, i, j, k,m, n, q, r, s, t, u, v, w, x, z, A c, C a, b, c, C a, c, g a, c b, c
300 (2070) 300 (2070) 175 (1205) 500 (3445) 500 (3445) 300 (2070)
Remarks: a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S, 8 in. and 10 NPS, 0.188 in. (5 mm) wall. c. With EPDM gasket d. For use with Allied Tube and Conduit Super-Flo and Dyna-Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 in. NPS. e. For use with Allied Tube and Conduit BLT thinwall steel sprinkler pipe in size 2 inch NPS. f. For use with Allied Tube and Conduit Dyna-Thread thinwall steel sprinkler pipe in size 2 inch NPS. g. For use with Allied Tube and Conduit XL, XL-II, Super-40, and Super-XL Thinwall steel sprinkler pipe in sizes: 2, 212, and 3 inch NPS at 300 psi. h. For use with AMS Tube Steady Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 in. NPS. i. For use with Bull Moose Tube EDDY-Lite Thinwall steel sprinkler pipe in size 2 inch NPS. j. For use with Bull Moose Tube EDDY-Thread Thinwall steel sprinkler pipe in size 2 inch NPS. k. For use with Bull Moose Tube EDDY Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 inch NPS. l. For use with Bull Moose Tube Ultra-EDDY Schedule 5 steel sprinkler pipe in size 2 inch NPS. m. For use with IDOD Systems Gal-7 Lightwall steel sprinkler pipe in size 2 inch NPS. n. For use with IDOD Systems Gal-Flo Lightwall steel sprinkler pipe in size 2 inch NPS. o. For use with IDOD Systems Gal-5 Schedule 5 steel sprinkler pipe in size 2 inch NPS. p. For use with IDOD Systems All-Gal Schedule 5 steel sprinkler pipe in size 2 inch NPS. q. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 3 and 4 inch NPS. r. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 212, 3, 4, and 6 inch NPS. s. For use with Wheatland Tube Mega-Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 inch NPS. t. For use with Western International Forest Products Rapid Thread Thinwall steel sprinkler pipe in size 2 inch NPS. u. For use with Wheatland Tube WLS Thinwall steel sprinkler pipe in size 2 inch NPS. v. For use with Wheatland Tube Mega-Thread Thinwall steel sprinkler pipe in size 2 inch NPS. w. For use with Wheatland Tube MLT Thinwall steel sprinkler pipe in size 2 inch NPS. x. For use with Wheatland Tube GL Thinwall steel sprinkler pipe in size 2 inch NPS. y. For use with Wheatland Tube WST schedule 5 steel sprinkler pipe in size 2 inch NPS. z. For use with Youngstown Tube EZ-Thread Thinwall steel sprinkler pipe in 2 inch NPS. A. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 inch NPS. B. Schedule 40 only. C. For use with BS1387 medium or heavier pipe, or EN 10255 pipe, or ISO 4200 pipe.
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation
Pipe Ends
Remarks
F-1 F-1
2, 212, 3 4, 5, 6
a, b, c, d a, b, c, d, q
FM Approvals
1-320
Product Designation
Pipe Ends
Remarks
Cut Groove Rolled Groove Cut Groove Rolled Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove Cut Groove Rolled Groove
a, b, c, h a, b, c, d, e, f, g, h, i, j, m, n, s, t, u, v, w, x, z, A k, l, o, p, y b, c B, c a, b, c, d, e, f, g, h, I, j, k, m, n, q, r, s, t, u, v, w, x, z, A c, C
175 (1205) 300 (2070) 175 (1205) 300 (2070) 250 (1725) 300 (2070) 300 (2070)
F-3
2, 212, 3, 4, 5, 6, 8, 10, 12 60, 76, 89, 114, 139, 165, 168, 219, 273 and 324 mm
F-3
Remarks: a. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. b. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S, 8 and 10 in. NPS, 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with Allied Tube and Conduit Super-Flo and Dyna-Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 in. NPS. e. For use with Allied Tube and Conduit BLT thinwall steel sprinkler pipe in size 2 inch NPS. f. For use with Allied Tube and Conduit Dyna-Thread thinwall steel sprinkler pipe in size 2 inch NPS. g. For use with Allied Tube and Conduit XL, XL-II, and Super-XL Thinwall steel sprinkler pipe in sizes: 2, 212, and 3 inch NPS. h. For use with AMS Tube Steady Flow Lightwall steel sprinkler pipe in sizes: 2, 2-12, 3, and 4 in. NPS. i. For use with Bull Moose Tube EDDY-Lite Thinwall steel sprinkler pipe in size 2 inch NPS. j. For use with Bull Moose Tube EDDY-Thread Thinwall steel sprinkler pipe in size 2 inch NPS. k. For use with Bull Moose Tube EDDY Flow Lightwall steel sprinkler pipe in sizes: 2, 212, 3, and 4 inch NPS. l. For use with Bull Moose Tube Ultra-EDDY Schedule 5 steel sprinkler pipe in size 2 inch NPS. m. For use with IDOD Systems Gal-7 Lightwall steel sprinkler pipe in size 2 inch NPS. n. For use with IDOD Systems Gal-Flo Lightwall steel sprinkler pipe in size 2 inch NPS. o. For use with IDOD Systems Gal-5 Schedule 5 steel sprinkler pipe in size 2 inch NPS. p. For use with IDOD Systems All-Gal Schedule 5 steel sprinkler pipe in size 2 inch NPS. q. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 3 and 4 inch NPS. r. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 2-12, 3, 4, and 6 inch NPS. s. For use with Wheatland Tube Mega-Flow Lightwall steel sprinkler pipe in sizes: 2, 2-12, 3, and 4 inch NPS. t. For use with Western International Forest Products Rapid Thread Thinwall steel sprinkler pipe in size 2 inch NPS. u. For use with Wheatland Tube WLS Thinwall steel sprinkler pipe in size 2 inch NPS. v. For use with Wheatland Tube Mega-Thread Thinwall steel sprinkler pipe in size 2 inch NPS. w. For use with Wheatland Tube MLT Thinwall steel sprinkler pipe in size 2 inch NPS. x. For use with Wheatland Tube GL Thinwall steel sprinkler pipe in size 2 inch NPS. y. For use with Wheatland Tube WST schedule 5 steel sprinkler pipe in size 2 inch NPS. z. For use with Youngstown Tube EZ-Thread Thinwall steel sprinkler pipe in 2 inch NPS. A. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 2, 2-12, 3, and 4 inch NPS. B. Schedule 40 only.
Beijing Tian Ning Yi He Pipe System Equipment Co Ltd, No. 2, North Road, Ju Yuan, Ma Pa Ju Yuan Industrial Base, Shunyi District, Beijing, P. R. China
Product Designation Pipe Size, mm Pipe Ends Remarks Max Working Pressure, psi (kPa)
GCQT08 GCQT08
Flange Flange
a, b, c a, c
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
2-8
a, b, c
300 (2070)
a. Min schedule pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
FM Approvals
1-321
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang Tsun Ta Liau Shiang Kaohsiung Hsien, Taiwan ROC
GT-425 Adapter Flanges for use with pipe conforming to the following min schedules. Cut groove: Schedule 40, 6 in. or smaller; Schedule 30, 8 in. or larger. Rolled groove: Schedule 10S, 6 in. or smaller; 0.188 in. (5 mm) wall, 8 in. or larger.
Product Designation Fitting Description Nominal Pipe Size, in. Max Working Pressure, psi
DUCCO Brand Flanges GT-425 Adapter Flange 2, 212, 3, 4, 6 8 300 (2070) 175 (1205)
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Remarks Max Working Pressure, psi (kPa)
a, b, c a, b, c c, d
a. b. c. d.
Min schedule pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. With EPDM gasket. BS 1387 pipe, Med. and Heavy.
Jinan Meide Casting Co Ltd, No. 3 Nanmen Road, Pingyin, Jinan, 250400 China
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
321
Split Flange
a, b, c, d, e a, b, c, d, e
Remarks: a. b. c. d. e. Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. Approved when supplied with EPDM gasket. Approved when supplied with an ISO PN10 bolt pattern. Approved when used with GB/T3092 regular and extra heavy pipe, ISO 4200, and BS 1387 Medium and Heavy pipe.
Qingdao V-Cart Piping Systems Co Ltd, JuiZhao Road, NanGuan Industry Zone, JiaoZhou City, Qingdao, China
Product Designation Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa) Remarks
16 (232) 16 (232)
a, b, c, d c, d
Min schedule cut groove pipe to be joined: 6 in. NPS or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. NPS or smaller Schedule 10S; 8 or 10 in. 0.188 in. (5 mm) wall. With EPDM gasket. For use with GB/T 3091-93 or GB/T 8163-99 Pipe.
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
QUIKFLANGE Style 90, grooved flange, for working pressure up to 250 psi (1725 kPa). For use with pipe conforming to the following min schedules: Cut groove endSchedule 40, 6 in. or smaller, Schedule 30, 8 in. or larger. Rolled grooved endSchedule 10S, 6 in. or smaller, 0.188 in. wall, 8 in. or larger.
Product Description Fitting Description Nominal Pipe Size
90
QUIKFLANGE*
FM Approvals
1-322
*For use with roll groove Allied Tube & Conduit Dyna Flow at 175 psi (1205 kPa) rating. 2, 3, 4 in. Product Designation Nominal Pipe Size, in. Pipe Ends Remarks Max Working Pressure psi (kPa)
QUIKFLANGE, 90
a, b, c, d a, b, c, e
a. b. c. d. e.
Minimum schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 Wall (5 mm Wall). With EPDM EP gasket (green stripe). For use with Allied Tube and Conduit Dyna-Flow Lightwall steel sprinkler pipe in sizes: 2, 3 and 4 in. NPS. For use with ISO 65 steel sprinkler pipe in sizes: 140 and 165 mm NPS.
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
FireShield Series 300 Products.
Product Designation Nominal Pipe Size, in. Remarks Max Working Pressure, psi (kPa)
2 to 8
a, b, c
175 (1205)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket.
SCE Company Ltd, Unit E&F, 20/F., CDW Building, 388 Castl Peak Road, Tsuen Wan, N.T., Hong Kong
Product Designation Nominal Pipe Size, in. Pipe Ends Max Working Pressure, psi (kPa)
Remarks
321 321
Remarks: a. b. c. d.
2,
212,
3, 4, 5, 6
a, b, c, d a, b, c, d
76.1, 165 mm
Minimum schedule cut groove pipe to be joined: 6 in. NPS and smaller Schedule 40; 8 in. NPS and larger Schedule 30. Minimum schedule rolled groove pipe to be joined: 6 in. NPS and smaller Schedule 10S; 8 in. NPS and larger 0.188 in. (5 mm) wall. Approved when supplied with EPDM gasket. Approved when supplied with an ISO PN10 bolt pattern.
SPT Metal Corp, 19-1 Da Yeh St, Da Liao, Hsiang, Kaohsiung Hsien, Taiwan ROC
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
Split Flange Split Flange Style 61 Split Flange Split Flange Style 62
a. b. c. d. e. f. g. h. i. j.
c, e, f, g, h, i, j c, d c, d a, b, c a, b, c a, c
300 (2070) 300 (2070) 250 (1725) 175 (1205) 300 (2070)
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For metric pipe per BS 1387 medium or equal. When joining Allied Tube & Conduit XL threadable Thinwall pipe, 1-2 in. only. All FM Approved for use on Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. When joining Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. For use with Central Sprinkler TL threadable Thinwall pipe. For use with Bull Moose Tube EDDY-Flow pipe.
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Working Pressure, psi (kPa)
a, b, c
b, c, d
FM Approvals
1-323
Product Designation
Fitting Description
Remarks
Split Flange Split Flange Split Flange ANSI Class 300 Split Flange ANSI 125/150 2,
b, c, d d, e d
3, 4, 2, 5, 6, 8, 10, 12 2, 212, 3, 4, 6
SS-41
a. b. c. d. e.
d, e
212, 4 in. British Standard BS 1387 medium or heavy pipe. Min schedule cut groove pipe to be joined: 8 in. or smaller Schedule 40. Min schedule rolled groove pipe to be joined: 8 in. or smaller Schedule 10. EPDM gasket. Stainless steel material.
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Grinnell Flange. For use with pipe conforming to the following min schedules, at the pressure ratings indicated.
Product Designation Fitting Description Remarks Nominal Pipe Size, in. Pressure Rating, psi (kPa)
7012
a, b, c, d e
Cut groove-ended: 6 in. or smaller - Schedule 40, 300 psi (2070 kPa); 8 in. or larger - Schedule 30, 300 psi (2070 kPa). Rolled groove-ended: 2, 212, 3 in. NPS - Allied Tube & Conduit FM Approved XL, Super-40 and Super-XL Lightwall pipe, 300 psi (2070 kPa). Rolled groove-ended: 6 in. or smaller - Schedule 10; 8 in. or larger - 0.188 in. (5 mm) wall, 300 psi (2070 kPa). Rolled groove-ended: Allied Tube & Conduit Dyna-Flow. 2, 212, 3 in., 300 psi (2070 kPa); Allied Tube & Conduit Super-Flo. 2-4 in., 300 psi (2070 kPa). Gruvlok standard grooved-end fittings for use with Gruvlok couplings. e. Metric pipe: equivalent to 76.1, 108, 133, 139.7, 165.1 and 323.9 mm British Standard 1387, medium or equal.
a. b. c. d.
Product Designation
Fitting Description
Remarks
7012T
2-8
Grinnell Flange
a, b, c
175 (1205)
a. 212, 4 in. British Standard: BS 1387 medium or heavy pipe. b. Min schedule cut groove pipe to be joined: 8 in. or smaller Schedule 40. c. Min schedule rolled groove pipe to be joined: 8 in. or smaller Schedule 10. Product Designation Fitting Description Nominal Pipe Size, mm Max Rated Pressure, psi (bar)
Pipe Ends
7013
Cut groove-ended: 6 in. or smaller - Schedule 40, 300 psi (2070 kPa); 8 in. or larger Schedule 30, 300 psi (2070 kPa). Rolled groove-ended: 2, 212, 3 in. NPS Allied Tube & Conduit FM Approved XL, Super-40 and Super-XL Lightwall pipe, 300 psi (2070 kPa). Rolled groove-ended: 6 in. or smaller Schedule 10, 300 psi (2070 kPa); 250 psi (1725 kPa) or Schedule 30, 8 in. or larger 0.188 in. (5 mm) wall, 300 psi (2070 kPa). Rolled groove-ended: Allied Tube & Conduit Dyna-Flow. 2, 212, 3 in., 300 psi (2070 kPa); Allied Tube & Conduit Super-Flo. 2-4 in., 300 psi (2070 kPa).
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max. Working Pressure psi (kPa)
Grinnell Figure 71
Split Flange
a, b, c c, d, g, e, f, h, k, m, q, r, s, t c, j, u c, l c, l c, l
250 (1725) 250 (1725) 175 (1205) 250 (1725) 175 (1205) 250 (1725)
FM Approvals
1-324
Product Designation
Fitting Description
Remarks
60.3, 76.1, 88.9, 114.3, 139.7, 165.1, 168.3, 219.1, 273.0, 323.9 mm Class PN16
c, v
250 (1725)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. e. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. f. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. g. For use with Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. h. For use with Central Sprinkler TL threadable Thinwall pipe. j. For use with Bull Moose Ultra-EDDY pipe and IDOD Systems Sch. 5 pipe. k. For use with Allied XL, Wheatland WLS Thinwall pipe. l. For use with 3 through 6 in. Northwest EZ-Flow pipe. m. For use with Youngstown Fire-flo, EZ-Thread pipe, and Steady-flow pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. v. BS 1387 pipe, medium and heavy wall or ISO 4200 pipe. Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Rated Pressure, psi (kPa)
71
Split Flange
2-12 2-4 2 3-4 6 4, 6 60.3, 76.1, 88.9, 114.3, 139.7,165.1 168.3, 219.1, 273.0, 323.9 mm Class PN16
a, b, c c, d, g, e, k, m, q, r, s, t c, j, u c, l c, l c, l c, v
250 (1725) 250 (1725) 175 (1205) 250 (1725) 175 (1205) 250 (1725) 250 (1725)
a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. With EPDM gasket. d. For use with Allied Tube & Conduit Dyna-Flow non-threadable Lightwall pipe. e. For use with Allied Tube & Conduit BLT threadable Thinwall pipe. f. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall pipe. g. For use with Allied Tube & Conduit Super-Flo non-threadable Lightwall pipe. j. For use with Bull Moose Ultra-EDDY pipe and IDOD Systems Sch. 5 pipe. k. For use with Allied XL, Wheatland WLS Thinwall pipe. l. For use with 3 through 6 in. Northwest EZ-Flow pipe. m. For use with Youngstown Fire-flo, EZ-Thread pipe, and Welded TubeBerkeley LLC Steady-Flow pipe. q. For use with Wheatland Tube Co. Mega-Flow non-threadable Lightwall pipe. r. For use with Wheatland Tube Co. Mega-Thread threadable Thinwall pipe. s. For use with Wheatland Tube Co. WLS threadable Thinwall pipe. t. For use with Wheatland Tube Co. MLT threadable Thinwall pipe. u. For use with Wheatland Tube Co. WST Schedule 5 non-threadable Lightwall pipe. v. BS 1387 pipe, medium and heavy wall or ISO 4200 pipe.
Fitting Description
741
2, 212, 3, 4, 5, 6, 8, 10, 12
Style 742 Vic-Flange. For rated working pressures up to 250 psi (1725 kPa) joining Schedule 30 cut groove-ended pipe.
742 Vic-Flange 14, 16
Style 743 Vic-Flange. For working pressures up to 500 psi (3445 kPa). For use with pipe conforming to the following min schedules: Cut or rolled groove-ended - Schedule 40, 6 in. or smaller; Schedule 30, 8 in. or larger.
743 Vic-Flange ANSI Class 300 212, 3, 4, 5, 6, 8, 10, 12
FM Approvals
1-325
Product Designation
Fitting Description
Style 744 Vic-Flange. For working pressures up to 175 psi (1205 kPa). For use with pipe conforming to the following min schedules: Cut groove-ended - Schedule 40, 6 in. or smaller; Schedule 30, 8 in. or larger. Rolled groove-ended - Schedule 10S, 6 in. or smaller; 0.188 in. (5 mm) wall, 8 in. or larger. Also FM Approved for use on Allied XL, Dyna-Flow, EZ-Flow and Super-Flo Lightwall pipe in appropriate sizes.
744 Vic-Flange ANSI Class 125, 150 2, 212, 3, 4, 5, 6, 8
Style 2041
Split Flange
a, b, c, e, f, h, j c, d
a. b. c. d. e. f. h. j.
Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10S; 8 in. 0.188 in. (5 mm) wall. With EPDM gasket. For metric pipe per BS 1387 medium or equal. For use with Wheatland Mega-flow pipe. All FM Approved for use on Allied Tube & Conduit Dyna-Flow and Super-flo non-threadable Lightwall pipe. For use on Northwest EZ-Flow non-threadable Lightwall pipe in 4 in. nominal size. For use with Bull Moose Tube EDDY-Flow pipe.
PIPE FITTINGS
These fittings are suitable for interconnecting piping, valves and other components in both wet and dry automatic sprinkler systems. Installation should be according to applicable sprinkler system fabrication rules. These rules limit the minimum size of sprinkler piping to 1 in., nominal. FM Approved pipe fittings of smaller sizes are intended for use as valve trim, gauge connections, and for other peripheral service. The water flow path of the sprinkler system cannot be designed using smaller sizes than 1 in., nominal. Unless otherwise noted in the listing, these fittings have 175 psi (1205 kPa) rated working pressure. Threaded connections on fittings can be made to FM Approved threadable thinwall pipe or to Schedule 40 pipe. The Table on page provides a summary of pipes which are FM Approved for threaded connections. Also refer to the specific listings under the heading Steel Pipe. The fittings manufacturers installation instructions must be observed in all cases. When connections are made to FM Approved pipe, the pipe manufacturers installation instructions must also be followed. Unless otherwise stated below, the maximum ambient temperature to which these fittings should be subjected is 225F (107C).
AGF Mfg Inc, 100 Quaker Lane, Malvern PA 19355
Cast elbows and zee fittings for use as sprinkler drops.
Model No. Ends Pressure Drop for 20 Ft/Sec Flow
6100A Elbow 6100B Elbow 6000A 6000B 6000C 6000D 6000E 6000F
1 Plain End 1 Plain End 1 FNPT 1 Plain End 1 Plain End1 Plain End 1 FNPT1 Plain End 1 Plain End1 FNPT 1 Plain End12 FNPT 1 FNPT1 FNPT 1 FNPT12 FNPT
5.5 psi-54 gpm 5.5 psi-54 gpm 5.5 psi-54 gpm 3.6 psi-19 gpm 5.5 psi-54 gpm 3.6 psi-19 gpm
FM Approvals
1-326
AJS Co Ltd, 1001 Namsung Plaza #345-30, Gasan-dong, Geumcheon-gu, Seoul 153-782 Korea
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Rated Pressure, psi (kPa)
AF 1111
AF 1112
AF 1130
AF 1140
AF 1150
1-8 in., 76, 139, 165, and 216 mms 1-8 in., 76, 139, 165, and 216 mms 1-8 in., 76, 139, 165, and 216 mms 21 in. through 86 in., and 7665 mm through 216165 mm 1-8 in., 76, 139, 165, and 216 mms 1-8 in., 76, 139, 165, and 216 mms 1-8 in., 76, 139, 165, and 216 mms 1-8 in., 76, 139, 165, and 216 mms 21 in. through 86 in., and 7665 mm through 216165 mm 1-8 in., 76, 139, 165, and 216 mms
90 Elbow
a, b, c
45 Elbow
a, b, c
Equal Tee
a, b, c
Concentric Reducer
a, b, c
Cap
a, b, c
175 (1205)
AF 1311
90 Elbow
a, b, d
AF 1312
45 Elbow
a, b, d
AF 1330 AF 1340
a, b, d a, b, d
AF 1350
Cap
a, b, d
175 (1205)
a. b. c. d.
Min. schedule of cut groove to be joined: 8 in. or smaller schedule 40. Min. schedule of rolled groove to be joined: 8 in. or smaller schedule 10. Carbon Steel. Stainless Steel.
ATUSA empresarial SL, Aptd. Correos 8, Poligono, Industrial Agurain S/N, 01200 Salvatierra, lava, Spain
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Working Pressure, psi (kPa)
1 1A 2 2A 3 40 41 90 90R
Long Sweep Bend, M/F Short Bend, M/F Long Sweep Bend, F/F Short Bend, F/F Long Sweep Bend, M/M 45 Long Sweep Bend, M/F 45 Long Sweep Bend, F/F Elbow, F/F Reducing Elbow, F/F
92 92R
95 96 97 98 120
Union Elbow, Flat Seat, F/F Union Elbow, Taper Seat, F/F Union Elbow, Flat Seat, M/F Union Elbow, Taper Seat, M/F 45 Elbow, F/F
18, 14, 38, 12, 34, 1, 114, 112, 2, 212 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 14, 38, 12, 34, 1, 114, 112, 2, 212 38, 12, 34, 1, 114, 112, 2, 212 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 1 8, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 3 8 1 4, 12 14, 38 3 4 3 8, 1 2 1 x 12, 34 114 12, 34, 1 112 34, 1, 114 2 x 1, 114, 112 212 2 18, 38, 12, 34, 1, 14, 112, 2, 212 1 12 38, 34 12, 1 34, 14 1, 112 1, 112 114, 1 38 12, 12 34, 34 1, 1 114 38, 12, 34, 1, 114, 112, 2 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 38, 12, 34, 1, 114, 112, 2 1 4, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 38, 12, 34, 1, 114, 112, 2, 212
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
FM Approvals
1-327
Product Designation
Fitting Description
130R
Tee, Bullhead, F
130R
130R
130R
38, 12, 34, 1, 114, 112, 2, 212 1 8, 3 8, 1 2, 3 4, 1, 114, 112, 2, 212 3 8 1 4, 12 x 14, 38 3 4 1 4, 3 8, 1 2 1 14, 38, 12, 34 114 38, 12, 34, 1 112 38, 12, 34, 1, 114 2 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 38 12, 34 12 x 34, 1 34 1, 114 1 114, 112 114 112, 2 1 1 2 x 2 2 212 1 2 3 8 x 3 8 34 38 12, 34 x 12 38, 34 12 x 12, 1 38 34, 1 12 x 38, 1 12 12, 1 x 12 34, 1 34 12, 1 x 34 34, 114 12 1, 14 34 12, 114 34 x 34, 1 114 34 1, 114 1 38, 114 1 12, 114 1 34, 114 1 1, 112 12 114, 112 34 114, 112 x 1 1, 112 1 114, 112 114 x 1, 112 114 114 2 12 x 112, 2 12 2, 34 x 112, 2 1 112, 2 2 114 x 1, 2 114 114, 2 114 112, 2 112 1, 2 112 112, 212 2 2 12 34 38, 34 1 12, 1 114 34, 114 112 1, 112 2 114 1 2 1 2 3 8, 34 34 38, 12 1 x 1 3 8, 1 2, 3 4 114 x 114 12, 34, 1 12 x 112 12, 34, 1, 114 1 2 x 2 12, 34, 1, 114, 112 2 12 212 112 14, 38, 12, 34, 1, 114, 112, 2, 212 38, 12, 34,
450 (3100)
450 (3100)
1,
114,
18
112,
241
245
18 x 14, 38 3 4 3 8, 1 2 1 38, 12, 34 114 38, 12, 34, 1 112 x 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 x 1, 114, 112, 2 14 18 38 18, 14 1 2 1 8, 1 4, 3 8 34 x 14, 38, 12 1 38, 12, 34 114 38, 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 1, 114, 112, 2 14 18 38 18, 14 1 2 1 4, 3 8 3 4 3 8, 1 2 1 1 2, 3 4 114 12, 34, 1 112 x 34, 1, 114 2 1, 114, 112 212 2
3 8 1 2
14
450 (3100)
450 (3100)
FM Approvals
1-328
Product Designation
Fitting Description
246
270 271 280 281 290 291 294 300 330 331 340 341 344 526 529A 531
Socket, F/F Right and Left Socket, F/F Hex Nipple, M/M Right and Left Hex Nipple, M/M Plug, M Plain Plug, M Plug, M Cap, F Union, Flat Seat, F/F Union, Flat Seat, M/F Union, Taper Seat, F/F Union, Taper Seat, M/F Union, Taper Seat, M/M Extension Tube, M/F
18 14 12 x 14, 38 3 4 3 8, 1 2 1 x 12, 34 14 12, 34, 1 1 12 34, 1, 114 1 2 x 1, 114, 112 212 112, 2 38, 12, 34, 1, 114, 112, 2, 212
38, 12, 34, 3 8, 1 2, 3 4,
14 3 8
450 (3100)
1, 114, 112, 2
1, 114, 112, 2, 212 1, 114, 112, 2, 212 1, 114, 112, 2 1, 114, 112, 2, 212
3 8, 1 2, 3 4,
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
90 Elbow, Grooved Ends 90 45 Elbow, Grooved Ends 120 45 Elbow, Grooved Ends 120 Equal Tee, Grooved Ends 130 Equal Tee, Grooved Ends 130 Reducing Tee, Grooved Ends 130R
114, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2112, 31, 112, 2, 212, 41, 2, 212, 3, 52, 3, 4, 62, 212, 3, 4, 5, 82, 3, 4, 5, 6 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 61, 2, 212, 3, 4, 5, 12, 3, 4, 5, 6 82 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 8212, 3, 4, 5, 6 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 8212, 3, 4, 5, 6
500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450)
Equal Cross, Grooved Ends Equal Cross, Grooved Ends Concentric Reducer, Grooved Ends
EO Model 240
500 (3450)
EO Model 246
500 (3450)
FM Approvals
1-329
Product Designation
Fitting Description
Grooved End Cap 300 Grooved End Cap 300 FlangeGroove Adapter 321 FlangeGroove Adapter 321
Action Fire Fab & Supply Inc, 1600 W Linne Rd, Tracy CA 95376
Product Designation Fitting Description Nominal Pipe Size, in. Pressure Rating, psi (kPa)
912 Elbow Sch. 10 Sch. 40 1114 Elbow Sch. 10 Sch. 40 2212 Elbow Sch. 10 Sch. 40
2-5 6-8 2-5 6-8 2-5 6-8 2-5 6-8 2-5 6-8 2-5 6-8 112, 2; 33114, 112, 2, 212; 312312114, 112, 2, 212, 3; 44114, 112, 2, 212, 3, 312; 55114, 112, 2, 212, 3, 312, 4; 66114, 112, 2, 12, 3, 312, 4, 5; 2 88114, 112, 2, 212, 3, 312, 4, 5, 6 212 by X by Y through 5 by X by Y 6 by X by Y through 8 by X by Y Where X and Y are As Ordered 2-5 6-8 212112, 2; 32, 212; 212, 3; 42, 212, 3, 312; 52, 212, 3, 312, 4; 62, 212, 3, 312, 4, 5; 82, 212, 3, 312, 4, 5, 6 212112, 2; 32, 212; 122, 212, 3; 3 42, 212, 3, 312; 52, 212, 3, 312, 4; 62, 212, 3, 312, 4, 5; 82, 212, 3, 312, 4, 5, 6 2-5 3142, 6-8 2, 212, 3 212212114,
45 Elbow Sch. 10 Sch. 40 90 Elbow Sch. 10 Sch. 40 Straight Tee Sch. 10 Sch. 40 Reducing Outlet Tee Sch. 10 Sch. 40
300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070)
250 (1725)
Grooved Cap Sch. 10 Sch. 40 Grooved Cap w 12 or 34 in. FNPT Threaded Outlet Sch. 10
FM Approvals
1-330
Product Designation
Fitting Description
Fig. 610
Fig. 610
1141; 1121, 114; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 41, 114, 112, 2, 212, 3, 312; 51, 114, 112, 2, 212, 3, 312, 4; 61, 114, 112, 2, 212, 3, 312, 4, 5; 81, 114, 112, 2, 212, 3, 312, 4, 5, 6 1141; 1121, 114; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 41, 114, 112, 2, 212, 3, 312; 51, 114, 112, 2, 212, 3, 312, 4; 61, 114, 112, 2, 212, 3, 312, 4, 5; 81, 114, 112, 2, 212, 3, 312, 4, 5, 6 114, 12, 34; 11414, 12, 34, 1; 11214, 12, 34, 1, 114; 214, 12, 34, 1, 114, 112; 1214, 12, 34, 1, 114, 112, 2; 2 314, 12, 34, 1, 114, 112, 2, 212; 31214, 12, 34, 1, 114, 112, 2, 212, 3; 414, 12, 34, 1, 114, 112, 2, 212, 3, 312; 514, 12, 34, 1, 114, 112, 2, 212, 3, 312, 4; 614, 12, 34, 1, 114, 112, 2, 212, 3, 312, 4, 5; 8 14, 12, 34, 1, 114, 112, 2, 212, 3, 312, 4, 5, 6
300 (2070)
250 (1725)
300 (2070)
250 (1725)
300 (2070)
250 (1725)
1 1 1 4 1 1 2 2 2 1 2 3 3 1 2 4 5 6 8
3F
Female Thread
FM Approvals
1-331
Product Designation
Fitting Description
3F
Female Thread
1 1 4 1 1 2 2 2 1 2 3 3 1 2 4
3M
Male Thread
1 1 1 4 1 1 2 2 2 1 2
Standard groove-ended fittings for use with flexible couplings. 500 psi (3445 kPa) rated working pressure.
Designation Product Description Nominal Pipe Size, in.
Fittings for use on Schedule 10 or heavier plain end pipe. NPT internal threaded branch connection.
FM Approvals
1-332
Product Designation
Fitting Description
350 360
12, 34,
370
380
Coupling
End Conn.
1 to 12 1 to 12 1 to 12 1 to 12 6 by 3, 4; 8 by 5, 6; 10 by 6, 8; 12 by 8, 10 1 to 12 1 to 12 114 to 12 114 to 12 2 to 8 2 to 8 2 to 8 2 to 8 1 to 12 2 to 8 3 by 3 by 2; 4 by 4 by 2, 212, 3; 6 by 6 by 2, 3, 4; 8 by 8 by 2, 3, 4, 5, 6 114 by 114 by 1; 1121121, 114; 221, 114, 112; 122121, 114, 112, 2; 2 331, 114, 112, 2, 212; 441, 114, 112, 2, 212, 3; 551, 112, 2, 212, 3, 4; 661, 112, 2, 212, 3, 4, 5; 88112, 2, 212, 3, 4, 5, 6; 1010112, 2, 212, 3, 4, 5, 6, 8; 12121, 2, 212, 3, 4, 5, 6, 8, 10 1 thru 12 2 thru 8 112 by 1, 114; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 5, 6, 8; 124, 6, 8, 10 114 by 1; 11234, 1, 114; 234, 1, 114, 112; 212114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 5, 6, 8; 124, 6, 8, 10
G by G G by G G by G G by G F by G
175 (1205)
90 L. R. Elbow 45 L. R. Elbow 90 Drain Elbow 45 Drain Elbow 90 Elbow 45 Elbow 90 L. R. Elbow 45 L. R. Elbow Tee Tee Reducing Tee
G by G G by G G by G G by G Pl. by Pl. Pl. by Pl. Pl. by Pl. Pl. by Pl. G by G by G Pl. by Pl. by Pl. Pl. by Pl. by Pl.
Reducing Tee
G by G by G
Ecc. Reducer
G by G
FM Approvals
1-333
Fitting Description
End Conn.
Swag Nipple
Swag Nipple
Tee Wye
True Y True Y Flanged Adapter Flanged Adapter Nipple Nipple 90 Elbow Adapter 45 Elbow Adapter Cap Bull Plug
2 by 1, 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 114, 112, 2, 3, 312, 4, 5 2 by 1, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 114, 112, 2, 212, 3, 312, 4, 5 1 to 12 2 to 8 3 by 3 by 2, 212; 442, 212, 3; 552, 3, 4; 662, 3, 4, 5; 884, 5, 6; 10104, 5, 6, 8; 12124, 6, 8, 10 2 by 2 by 2; 212212212; 333; 312312312; 443, 4; 553, 4, 5; 663, 4, 5, 6; 883, 4, 5, 6, 8; 10103, 4, 5, 6, 8, 10; 12123, 4, 6, 8, 10, 12 4 by 3 by 3, 4; 533, 5; 543, 4; 646; 653, 4; 864, 8 1 to 12 2 to 8 1 to 12 2 to 8 1 to 12 1 to 12 1 to 6 1 to 6 1 to 12 2 to 6
114,
112;
G by G
G by Bev
G by G by G
175 (1205)
G by G by G
The Schedule 40 grooved, threaded, and flanged fittings have a rated working pressure as tabulated below:
Fitting Description Nominal Pipe Size Rated Working Pressure, psi (kPa)
End Conn.
G by G G by G G by G G by G F by G
300 (2070)
90 L. R. Elbow 45 L. R. Elbow 90 Drain Elbow 45 Drain Elbow 90 Elbow 45 Elbow 90 L. R. Elbow 45 L. R. Elbow Tee Tee Tee Reducing Tee
G by G G by G G by G G by G Pl. by Pl. Pl. by Pl. Pl. by Pl. Pl. by Pl. G by G by G G by G by T Pl. by Pl. by Pl. Pl. by Pl. by Pl.
FM Approvals
1-334
Fitting Description
End Conn.
Reducing Tee
Reducing Tee
Conc. Reducer
Ecc. Reducer
Ecc. Reducer
Swag Nipple
Swag Nipple
114 by 114 by 1; 112 by 112 by 1, 114; 2 by 2 by 1, 114, 112; 212 by 212 by 1, 114, 112, 2; 3 by 3 by 1, 114, 112, 2, 212; 4 by 4 by 1, 114, 112, 2, 212, 3; 5 by 5 by 1, 112, 2, 212, 3, 4; 6 by 6 by 1, 112, 2, 212, 3, 4, 5; 8 by 8 by 112, 2, 212, 3, 4, 5, 6; 10 by 10 by 112, 2, 212, 3, 4, 5, 6, 8; 12 by 12 by 1, 2, 212, 3, 4, 6, 8, 10 2 by 2 by 34, 1, 114, 112; 212 by 212 by 1, 112, 2; 3 by 3 by 34, 1, 112, 2, 212; 4 by 4 by 34, 1, 112, 2, 212, 3; 5 by 5 by 2, 3, 4; 662, 212, 3, 4, 5; 882, 3, 4, 5, 6; 10102, 3, 4, 5, 6, 8; 12123, 4, 6, 8, 10 5 by 5 by 8 and 6 by 6 by 8 4 by 4 by 212 and 6 by 6 by 212 1 thru 12 2 thru 8 112 by 1, 114; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 5, 6, 8; 124, 6, 8, 10 114 by 1; 1121, 114; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5 112 by 1; 21, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 5, 6, 8; 124, 6, 8, 10 114 by 1; 11234, 1, 114; 34, 1, 114, 112; 2 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 112, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 5, 6, 8; 124, 6, 8, 10 2 by 1, 114, 112; 121, 114, 112, 2; 2 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 114, 112, 2, 3, 312, 4, 5 2 by 1, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 114, 112, 2, 3, 312, 4, 5
G by G by G
G by G by T
G by T
G by G
G by T
G by G
G by T
FM Approvals
1-335
Fitting Description
End Conn.
Swag Nipple
Tee Wye
True Y True Y Flanged Adapter Flanged Adapter Nipple Nipple Nipple 90 Elbow Adapter 45 Elbow Adapter Threaded Adapter Cap Bull Plug
2 by 1, 114, 112; 2121, 114, 112, 2; 31, 114, 112, 2, 212; 3123; 41, 114, 112, 2, 212, 3, 312; 52, 212, 3, 4; 61, 114, 112, 2, 212, 3, 312, 4, 5 1 to 12 2 to 8 3 by 3 by 2, 212; 442, 212, 3; 552, 3, 4; 662, 3, 4, 5; 884, 5, 6; 10104, 5, 6, 8; 12124, 6, 8, 10 2 by 2 by 2; 212212212; 333; 312312312; 443, 4; 553, 4, 5; 663, 4, 5, 6; 883, 4, 5, 6, 8; 10103, 4, 5, 6, 8, 10; 12123, 4, 6, 8, 10, 12 4 by 3 by 3, 4; 533, 5; 543, 4; 646; 653, 4; 864, 8 1 to 12 2 to 8 1 to 12 2 to 8 1 to 12 1 to 12 1 to 12 1 to 6 1 to 6 1 to 4 1 to 12 2 to 6
G by Bev
G by G by G
G by G by G
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
125 lb threaded Cast Iron Fittings. 175 psi (1205 kPa) rated pressure.
Product Description
Fitting Description
90 Elbow 90 Elbow Flanged by threaded 45 Elbow 45 Elbow Flanged by threaded 2212 Elbow 90 Reducing Elbow
358
Tee
to 212 by 14, 38; 34 by 12; 1 by 12, 34; 114 by 12, 34, 1; 112 by 12, 34, 1, 114; 2 by 12, 34, 1, 114, 112; 212 by 1, 114, 112, 2; 3 by 114, 112, 2, 212; 312 by 3; 4 by 2, 212, 3, 312; 5 by 212, 3, 4; 6 by 3, 4, 5 14 to 6
1 2
3 4
FM Approvals
1-336
Product Description
Fitting Description
359
Reducing Tee
360 361
367
Concentric Reducer
368
Eccentric Reducer
by 12 by 14, 38, 34, 1; by 34 by 14, 38, 12, 1; 34 by 12 by 12, 34; 34 by 14 by 34; 1 by 1 by 14, 12, 34, 114, 112, 2; 1 by 34 by 12, 34, 1; 1 by 12 by 12, 34, 1; 1 by 14 by 1; 114 by 114 by 12, 34, 1, 112, 2; 114 by 1 by 12, 34, 1, 114, 112, 2; 114 by 34 by 34, 1, 114; 114 by 12 by 12, 1, 114; 12 by 112 by 12, 34, 1, 114, 2, 212; 1 112 by 114 by 12, 34, 1, 114, 112; 112 by 1 by 12, 34, 1, 114, 112, 2; 112 by 34 by 112, 2; 112 by 12 by 114, 112; 2 by 2 by 12, 34, 1, 114, 112, 212, 4; 2 by 112 by 12, 34, 1, 114, 112, 2, 212; 2 by 114 by 12, 34, 1, 114, 112, 2, 212; 2 by 1 by 1, 114, 112, 2, 212; 2 by 34 by 114, 112, 2; 2 by 12 by 112, 2; 212 by 212 by 12, 34, 1, 114, 112, 2, 4; 212 by 2 by 12, 34, 1, 114, 112, 2, 212; 212 by 112 by 112, 2, 212; 212 by 114 by 112, 2, 212; 212 by 1 by 2, 212; 212 by 34 by 212; 212 by 12 by 2, 212; 3 by 3 by 12, 34, 1, 114, 112, 2, 212, 312, 4, 5; 3 by 212 by 1, 114, 112, 2, 212, 3; 3 by 2 by 112, 2, 212, 3; 3 by 112 by 212, 3; 3 by 114 by 3; 3 by 12, 34, 1 by 3; 312 by 312 by 1, 114, 112, 2, 212, 3, 4, 5; 312 by 3 by 112, 2, 212, 3, 312, 4, 5; 312 by 212 by 212, 3, 312, 4; 312 by 2 by 312; 312 by 114 by 3; 4 by 4 by 34, 1, 114, 112, 2, 212, 3, 5, 6; 4 by 312 by 112, 2, 212, 3, 312, 4, 5; 4 by 3 by 114, 112, 2, 212, 3, 4; 4 by 212 by 212, 3, 4, 5; 4 by 2 by 2, 212, 3, 4; 4 by 34, 1, 114, 112 by 4; 5 by 5 by 112, 2, 212, 3, 4, 6; 5 by 4 by 212, 3, 4, 5, 6; 5 by 312 by 3, 4, 6; 5 by 3 by 4, 6; 5 by 2, 212 by 5; 6 by 6 by 114, 2, 212, 3, 4, 5; 6 by 5 by 112, 312, 6; 6 by 4 by 3, 4, 6; 6 by 312, 212, 2, 112 by 6; 6 by 3 by 4 12 through 6 1 by 34; 114 by 1; 112 by 1, 114; 2 by 1, 114, 112; 12 by 1, 114, 112, 2; 2 3 by 1, 114, 112, 2, 212; 312 by 114, 112; 4 by 1, 114, 112, 2, 212, 3, 312; 5 by 2, 3; 6 by 114, 212, 4, 5 34 by 12; 1 by 12, 34; 114 by 12, 34, 1; 112 by 12, 34, 1, 114; 2 by 12, 34, 1, 114, 112; 212 by 112, 2; 3 by 34, 2, 212; 4 by 2, 212, 3 34 by 12; 1 by 12, 34; 114 by 12, 34, 1; 112 by 12, 34, 1, 114; 2 by 12, 34, 1, 114, 112; 212 by 1, 114,112, 2; 3 by 1, 114, 112, 2, 212; 312 by 2, 3; 4 by 1, 114, 112, 2, 212, 3
3 4
1 2
FM Approvals
1-337
Product Description
Fitting Description
383
Hex Bushing
Sq. Hd. Plug, Cored Solid Plug Bar Plug, Cored Plug, Csunk
by 18; by 18, 14; 12 by 18, 14, 38; 34 by 18, 14, 38, 12; 1 by 18, 14, 38. 12, 34; 114 by 14, 38, 12, 34, 1; 112 by 14, 38, 12, 34, 1, 114; 2 by 14, 38, 12, 34, 1, 114, 112; 212 by 12, 34, 1, 114, 112, 2; 3 by 12, 34, 1, 114, 112, 2, 212; 312 by 1, 114, 112, 2, 212, 3; 4 by 1, 114, 112, 2, 212, 3, 312 4 to 6 212 to 6 14 by 18; 38 by 14; 12 by 14, 38; 34 by 38, 12; 1 by 12, 34; 14 by 12, 34, 1; 1 12 by 12, 34, 1, 114; 1 2 by 12, 1, 114, 112; 212 by 114, 112, 2; 3 by 114, 112, 2, 212; 312 by 212; 4 by 2, 212, 3 12 to 4 12 to 312 4 to 8 12 to 4
3 8
1 4
250 lb Standard Threaded CI Fittings. Rated working pressure is 400 psi (2760 kPa) 421 424 425 426 90 Elbow 45 Elbow Tee Reducing Tee to 4 to 4 14 to 4 34 by 34 by 12; 1 by 1 by 12, 34; 14 by 114 by 34, 1; 1 112 by 112 by 34, 1/ 114; 2 by 2 by 34, 1, 114, 112
12 14
125 lb Standard Flanged CI Fittings. Rated working pressure is 175 psi (1205 kPa) 801 802 803 90 Elbow 45 Elbow 90 Reducing Elbow 112 through 8 112 through 8 212 by 2; 3 by 2, 212; 4 by 2, 212, 3; 5 by 3, 4; 6 by 3, 4, 5; 8 by 4, 5, 6 2 through 8 3 by 2; 4 by 3; 5 by 4; 6 by 4, 5; 8 by 5, 6 3 through 8 4 through 8 112 through 8 212 by 212 by 2; 3 by 3 by 112, 2, 212; 4 by 4 by 112, 2, 212, 3; 5 by 5 by 212, 3, 4; 6 by 6 by 2, 212, 3, 4, 5; 8 by 8 by 3, 4, 5, 6 2 through 6 2 by 112; 212 by 112, 2; 3 by 112, 2, 212; 4 by 2, 212, 3, 312; 5 by 212, 3, 4; 6 by 2, 212, 3, 4, 5; 8 by 4, 5, 6 3 by 2, 212; 4 by 2, 212, 3; 5 by 4; 6 by 3, 4, 5; 8 by 4, 5, 6 3 through 8 1 through 8 1 through 8
804 804R
821 825
826
Eccentric Reducer
FM Approvals
1-338
Product Description
Fitting Description
1018 1035
250 lb Standard Flanged CI Fittings. Rated working pressure is 400 psi (2760 kPa). 831 832 833 90 Elbow 45 Elbow 90 Red. Elbow 4 to 6 4 to 6 4 by 212, 3; 5 by 3, 4; 6 by 4, 5 3 to 6 3 by 3 by 2, 212; 4 by 4 by 2, 212, 3; 5 by 5 by 4; 6 by 6 by 3, 4 4 by 2, 212, 3; 5 by 212, 3, 4; 6 by 212, 3, 4, 5 3 to 6 3 to 6 3 to 6
841 842
855
Conc. Reducer
150 lb Standard Threaded Malleable Iron Fittings. Rated working pressure is 300 psi (2070 kPa).
18
to 6 to 6
18
by 18; by 18, 14; by 14, 38; 34 by 14, 38, 12; 1 by 38, 12, 34; 114 by 12, 34, 1; 112 by 34, 1, 114; 2 by 34, 1, 114, 112; 212 by 112, 2; 3 by 2, 212; 4 by 3
3 8 1 2 18
1 4
to 4 to 4
18
1 2
45 Street Elbow Side Outlet Elbow Street Tee Tee Side Outlet Tee Cap
34 12
to 2
through 2
14
to 2 to 6
18
14
through 2 to 6
FM Approvals
1-339
Product Description
Fitting Description
1105R
Reducing Tee
1108 1138
by 14 by 18, 38; by 14 by 14, 38, 12; 38 by 38 by 12; 12 by 12 by 14, 38, 34, 1; 12 by 38 by 12, 38; 34 by 34 by 14, 38, 12, 1, 114; 34 by 12 by 34, 12; 34 by 38 by 34, 38; 34 by 14 by 34; 1 by 1 by 14, 38, 12, 34, 114, 112, 2; 1 by 34 by 12, 34, 1; 1 by 12 by 12, 34, 1; 1 by 14 by 1; 114 by 114 by 38, 12, 34, 1, 112, 2; 114 by 1 by 12, 34, 1, 114; 114 by 34 by 34, 1, 114; 114 by 12 by 1, 114; 112 by 112 by 12, 34, 1, 114, 112, 2; 112 by 114 by 12, 34, 1, 114, 112; 112 by 1 by 1, 114, 112; 112 by 34 by 34, 112; 112 by 12 by 112; 2 by 2 by 12, 34, 1, 114, 112, 212; 2 by 112 by 1, 114, 112, 2; 2 by 114 by 114, 112, 2; 2 by 12, 34, 1 by 2; 12 by 212 by 34, 1, 114, 112, 2, 3; 2 12 by 2, 112 by 212, 2; 2 3 by 3 by 34, 1, 114, 112, 212; 3 by 212 by 212, 2; 3 by 2 by 2, 3; 4 by 4 by 112, 2, 212, 3; 4 by 3 by 4 18 to 4 114 by 1 by 114 and 2 by 112 by 2 14 by 18; 38 by 18, 14; 12 by 18, 14, 38; 34 by 18, 14, 38, 12; 1 by 14, 38, 12, 34; 114 by 12, 34, 1; 112 by 12, 34, 1, 114; 2 by 12, 34, 1, 114, 112; 212 by 1, 114, 112, 2; 3 by 1, 114, 112, 2, 212; 312 by 2, 212, 3; 4 by 112, 2, 212, 3, 312; 5 by 4; 6 by 4 38 through 4 12 through 1
3 8
1 4
300 lb Standard Threaded Malleable Iron Fittings. Rated working pressure as follows:
Product Description
14 to 1 in. NPS 114 to 2 in. NPS 212 to 4 in. NPS 1161 1162 1161R
Fitting Description
2000 psi (13.8 mPa) 1500 psi (10.3 mPa) 1000 psi (6.9 mPa) 90 Elbow 45 Elbow 90 Reducing Elbow
to 4 to 4 38 by 14; 12 by 38; 34 by 12; 1 by 12, 34; 14 by 34, 1; 1 112 by 1, 114; 2 by 114, 112; 212 by 2; 3 by 212 14 to 3 14 to 3 14 to 3 12 to 2 14 to 4
1 4
1 4
FM Approvals
1-340
Product Description
Fitting Description
1164R
Reducing Tee
1165 1167
300 (2070) 400 (2760) 600 (4135) 600 (4135) 600 (4135) 600 (4135) 600 (4135)
1 4 1 4 1 4 1 2 3 8 1 4 3 8
to 3 to 4 to 4 to 2 to 1 to 2 to 2
Segmentally welded pipe fittings for use with flexible or rigid grooved pipe couplings, plain end fittings, welded or threaded joints, or flanges. Working pressures of 300 psi (2070 kPa) for non-threadable Thinwall pipe up to 4 in. NPS, Schedules 10 and 40 up to 8 in. NPS, and 250 psi (1725 kPa) for 10 and 12 in. NPS. Prefix 7 in model no. means made from non-threadable Thinwall pipe. Prefix 10 in model no. means made from Schedule 10 pipe. Prefix 40 in model no. means made from Schedule 40 pipe.
Product Designation Fitting Description Nominal Pipe Size, in.
7-7072 10-7072, 40-7072 7-7073 10-7073, 40-7073 7-7076 10-7076, 40-7076 7-7064 10-7064, 40-7064 7-7061 10-7061, 40-7061 7-7068 10-7068, 40-7068 7-7062 10-7062, 40-7062 10-7084, 40-7084 7-7075DR 10-7075DR, 40-7075DR
Reducer, Grooved, Concentric Reducer, Grooved, Concentric Reducer, Grooved, Eccentric Reducer, Grooved, Eccentric Reducer, Grooved MPT, Concentric Reducer, Grooved MPT, Concentric Reducing Tee, Grooved Grooved MPT Reducing Tee, Grooved Grooved MPT Tee, Reducing Grooved Tee, Reducing Grooved Cross, Grooved Cross, Grooved Tee, Bullhead, Grooved Tee, Bullhead, Grooved Adaptor Nipple, Grooved Flanged 90 Drain Elbow, Grooved 90 Drain Elbow, Grooved
114 by 1 through 4 by 3 114 by 1 through 12 by 10 114 by 1 through 4 by 3 114 by 1 through 12 by 10 114 by 12 through 4 by 3 114 by 12 through 12 by 6 114 by 114 by 14 through 4 by 4 by 3 114 by 114 by 12 through 12 by 12 by 10 114 by 114 by 14 through 4 by 4 by 3 114 by 114 by 12 through 12 by 12 by 10 114 through 4 114 through 10 2 by 2 by 212 through 312 by 312 by 4 2 by 2 by 212 through 6 by 6 by 8 112 through 12 114 through 4 114 through 12
FM Approvals
1-341
Product Designation
Fitting Description
22.5 Elbow, Grooved 22.5 Elbow, Grooved 11.2 Elbow, Grooved 11.2 Elbow, Grooved End Cap, Drain, Concentric End Cap, Drain, Concentric
114 through 4 114 through 12 114 through 4 114 through 12 112 through 4 112 through 12
Product Designation
Fitting Description
Remarks
7050E
7051E
7074E
114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 165 mm 2, 212, 3, 4, 6, 8 2, 212, 3, 4, 6, 8 2, 212, 3, 4, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 165 mm 2, 212, 3, 4, 6 76.1, 139.7, 165.1 mm
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
90 Elbow, Short Radius 45 Elbow, Short Radius Equal Tee, Short Radius Equal Tee, Grooved Ends
SE-2 SE-2
Gruvlok standard grooved-end fittings for use with Gruvlok couplings. Rated working pressure is 500 psi (3445 kPa) unless otherwise noted.
Product Designation Fitting Description Nominal Pipe Size, in. Pressure Rating, psi (kPa)
7050
90 Elbow
1-10 12 76, 108, 133, 139, 159, 165 mm 216, 267 mm 318 mm
90 Long Radius Elbow 90 Elbow Short Radius 90 Elbow Grooved Grooved 90 Elbow
7051 7051
45 Elbow 45 Elbow
1-10 12 76, 108, 133, 139, 159, 165 mm 216, 267 mm 318 mm
7051LR
1-10 12
500 (3445) 350 (2415) 175 (1205) 500 (3445) 400 (2760) 500 (3445) 300 (2070) 175 (1205) 175 (1205) 350 (2415) 500 (3445) 350 (2415) 175 (1205) 500 (3445) 400 (2760) 500 (3445) 350 (2415) 300 (2070) 175 (1205) 175 (1205) 500 (3445)
FM Approvals
1-342
Product Designation
Fitting Description
12 7053 1114 Elbow 1-10 12 7055 90 Adapter Elbow 1-10 12 7056 45 Adapter Elbow 1-10 12 7060 Tee 1-10 12 76, 108, 133, 139, 159, 165 mm 216, 267 mm 318 mm 7060S 7060SR 7060T 7061 Tee Shurjoint Radius Tee Grooved Grooved Tee Reducing Tee 114-8 2-6 114-8 1-10 12 7061T Grooved Reducing Tee Bull Head Tee 2112, 2122, 32, 3212, 42, 4212, 43, 63, 64 558 668 7063 Tee With Threaded Branch 1-10 12 7064 Reducing Tee With Threaded Branch 1-10 12 7065 Stand Pipe Tee 44212 66212 7066 Tee Wyes 222 101010 12123, 4, 6, 8, 10, 12 433868 1-10 12 7068T 7069 Grooved Cross 45 Lateral 2, 212, 3, 4, 5, 6 1-10 12 7070* Reducing Lateral 332 12126 12128, 121210 1-10 12 7072 Concentric Reducer 1121-108 126, 8, 10
350 (2415) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 175 (1205) 500 (3445) 400 (2760) 300 (2070) 175 (1205) 175 (1205) 500 (3445) 350 (2415) 175 (1205) 500 (3445) 500 (3445) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 500 (3445) 500 (3445) 500 (3445) 350 (2415) 500 (3445) 500 (3445) 400 (2760) 175 (1205) 500 (3445) 350 (2415) 500 (3445) 400 (2760) 500 (3445) 350 (2415) 500 (3445) 350 (2415)
7062
7067 7068*
7071
90 True Wye
FM Approvals
1-343
Product Designation
Fitting Description
7072T
7073
Eccentric Reducer
76 mm by 112 in. 76 mm by 2 in. 3 in. by 76 mm 4 in. by 76 mm 139 mm by 3 in. 139 mm by 4 in. 165 mm by 3 in. 165 mm by 4 in. 165 mm by 139 mm 6 in. by 76 mm 6 in. by 139 mm 122, 32, 3212, 2 42, 4212, 43, 54, 62, 63, 64, 65, 84, 86 1121-108 124, 6, 8, 10
500 (3445)
175 (1205)
7074
Cap
1-8 10 12 76, 108, 133, 139, 159, 165 mm 216, 267 mm 318 mm
7076T*
Swaged Nipple, GRVGRV Swaged Nipple With Threaded End Swaged Nipple, With Bevel Nipple, GRGR
2122, 32, 3212, 42, 4212, 43, 54, 62, 63, 64, 65, 84, 86 21-65 21-65 21-65
34-10
500 (3445) 350 (2415) 500 (3445) 400 (2760) 300 (2070) 175 (1205) 500 (3445) 400 (2760) 300 (2070) 175 (1205) 500 (3445) 350 (2415) 175 (1205)
12 7084T 7091 Gruvlok Flange Adaptor End All 212, 3, 4, 5, 6 11212, 11234, 121, 212, 1 234, 21, 21212, 21234, 2121 2-6 1121
500 (3445) 500 (3445) 500 (3445) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 500 (3445) 350 (2415) 175 (1205) 300 (2070)
7095*
7097
1121-108 124, 6, 8, 10
*Fabricated fittings FM Approved with rolled or cut-grooved ends. **Male threaded outlets.
FM Approvals
1-344
Gruvlok Sock-It quick connect fittings for plain-end pipe. Pressure rating of 300 psi (2070 kPa) for all items except those having one or more 2 in. (51 mm) connections. 2 in. (51 mm) items rated at 250 psi (1725 kPa). Pressure rating is 175 psi (1205 kPa) for all items when used with FM Approved Allied Tube & Conduit XL, Super-40 and Super-XL pipe, Allied Super-Flo pipe or Allied Tube & Conduit Dyna-Flow pipe, or IDOD Gal-7 or Gal-flo. 212 in. fittings rated at 175 psi for all pipes.
Product Designation Fitting Description Nominal Pipe Size, in.
7100 7101
7103 7105
7106
7107 7175
Product Designation Fitting Description
Sock-It Reducing Run Tee with NPT Internal Branch Connection Sock-It Coupling Sock-It 90 Elbow by NPT Outlet
Nominal Pipe Size, in.
1, 114, 112, 2 112, 34, 1; 11412, 34, 1; 11212, 34, 1 1, 114, 112, 2 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1 21212, 34, 1 114112, 34, 1; 11211412, 34, 1; 211212, 34, 1 1, 114, 112, 2 212, 34, 1
Pressure Rating, psi (kPa)
90 Elbow, Short Radius Tee, Short Radius Screwed Fitting 90 Elbows Screwed Fitting 45 Elbows Screwed Fitting Tees Screwed Fitting Reducing Tees
2-8 2-8
12, 34, 1, 114, 112, 2, 212
i1105R
i1125
Screwed Fitting Cross Screwed Fitting Straight Coupling Screwed Fitting Square Head Plug Screwed Fitting Cap Screwed Fitting Extension Piece
1, 114, 112, 2, 212 12, 34, 1, 114, 112, 2, 212 343412, 1134, 1112, 1341, 13434, 13412, 1121, 1141141, 11411434, 11411412, 1141114, 11411, 14134, 114112, 1 11114, 112112114, 1121121, 11211234, 11211212, 112114112, 1121141, 11211434, 11211412, 1121112, 11211, 112134, 112112, 11112, 114114112, 1141112, 22112, 22114, 221, 2234, 2212, 21122, 2112112, 21121, 211234, 211212, 21142, 212, 1121122, 121142, 212234, 1 22212 3412, 134, 112, 1141, 1121, 112114, 21, 2114, 2112, 2122 1, 114, 112, 2, 1141, 1121, 21 12, 34, 1, 114, 112, 2, 212 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 12112L, 122L, 34112L, 342L
12, 34,
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
300 (2070)
300 (2070)
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
FM Approvals
1-345
Product Designation
Fitting Description
i387
830 Model 831 DI, Long Street Elbow Model 832 DI, Long Street Tee
134, 112, 1141, 11434, 11412, 112114, 1121, 11234, 11212, 2112, 2114, 21, 234, 212 12, 34, 1, 114, 112, 2, 212 Screwed Fitting
300 (2070)
Screwed Fitting
AnvilStar LLC, Division of Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max. Working Pressure, psi (kPa)
E-1
E-2
K-1
SE-1 SE-5
90 Elbow, 1, 114, 112, 2, 212, 3, 4, 5, 6, Grooved Ends 8, 10, 12 76, 139.7, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 45 Elbow, 8, 10, 12 Grooved Ends 76, 139.7, 165 mm Grooved End Cap 1, 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 139.7, 165 mm 2, 2 12, 3, 4, 6, 8 90 Elbow, 76.1, 139.7, 165.1 mm Short Radius 1412, 34, 1 1 Grooved EndThreaded (NPT) 11212, 34, 1 212, 34, 1 Outlet Reducing Elbow 2 1212, 34, 1 334, 1 Grooved End Drain Elbow 2, 2 12, 3, 4, 6 2, 2 3, 4, 6, 8 76.1, 139.7, 165.1 mm 1, 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76, 139.7, 165 mm 12114-112 12112-2 122-212 12212-8 341-114 34114-112 34112-2 342-212 34212-8 1114-112 1112-2 12-212 1212-3 13-4 15-8 114112-2 1142-212 114212-3 1143-4 1145-8 1122 112212 1123-4 1124 1125-8 2212 23 24 26 28 12114-112 12112-2 341-114 34114-112 34112-2 1114-112 1112-2 114112-2 1122
12,
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Equal Tee, Short Radius Equal Tee, Grooved Ends Welded Branch Outlet Fitting, NPT a, b, c, d, f, g, h, i, j, l, m, n, o, p, q, r, t, u, v, w
MT-40
MT-40
e, k
175 (1205)
FM Approvals
1-346
Product Designation
Fitting Description
Remarks
1, 114, 112, 2, 212 1, 114, 112, 2, 212 1, 114, 112, 2, 212 1, 1 1 4, 112, 2
C.I. 90 Elbow C.I. 45 Elbow C.I. Equal Tee C.I. Equal Cross C. I. Reducing Elbow
112, 34 11412, 34, 1 11212, 34, 1, 114 212, 34, 1, 114, 112 1121, 1341, 1112, 34, 114, 112 14112, 34, 114, 112 1 11411412, 34, 1, 112, 2 112112, 34, 1, 114, 112 112114 12, 34, 1, 114, 112, 2 112112 12, 34, 1, 114, 2 212, 21142, 211212, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 212 22 112, 34 1141, 1121, 21 Ductile Iron Threaded Pipe Fittings 1, 114, 112, 2, 212 1, 1 1 4, 1, 112, 2, 212 2
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
300 (2070)
C.I. Reducing Coupling C.I. Reducing Cross D.I. 90 Elbow D.I. 45 Elbow D.I. Equal Tee D.I. Equal Cross D. I. Reducing Elbow
1 1 4,
112,
1 114 12, 34, 1, 114, 112 2 1121, 1341, 1112, 34, 114, 112 114112, 34, 114, 112 11411412, 34, 1, 112, 2 112112, 34, 1, 114, 112 112114 12, 34, 1, 114, 112, 2 112112 12, 34, 1, 114, 2 212, 21142, 211212, 34, 1, 114, 112, 2 2212, 34, 1, 114, 112, 212 112, 34 1141,
Remarks:
300 (2070) 300 (2070) 500 (3445) 500 (3445) 500 (3445) 500 (3445) 500 (3445)
500 (3445)
1121,
21
a. For use with FM Approved Schedule 10 and 40 steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, 3, 4, 6, and 8 in. NPS. b. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. c. For use with Allied Tube and Conduit XL threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, 2, 212, and 3 in. NPS. d. For use with Sawhill Tubular SLS threadable Thinwall steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. e. For use with Wheatland Tube WST Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. f. For use with Tex-Tube Tex-Flow Lightwall steel sprinkler pipe in sizes: 3, 4, and 6 in. NPS. g. For use with Welded TubeBerkeley LLC Steady-Flow Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. h. For use with Wheatland Tube Mega Flow Lightwall steel sprinkler pipe in sizes: 114, 112, 2, 212, 3, and 4 in. NPS. i. For use with Northwest Pipe EZ-Flow Lightwall steel sprinkler pipe in sizes: 4 and 6 in. NPS. j. For use with Youngstown Tube Fire-Flo Lightwall steel sprinkler pipe in sizes: 112, 2, 212, 3, and 4 in. NPS. k. For use with Bull Moose Tube Ultra EDDY Schedule 5 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. l. For use with Allied Tube & Conduit XL-II threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. m. For use with Allied Tube & Conduit Super-XL threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. n. For use with Allied Tube & Conduit Super 40 threadable Thinwall steel sprinkler pipe in sizes: 114, 112, 2, 212, and 3 in. NPS. o. For use with Allied Tube and Conduit BLT threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. p. For use with Allied Tube & Conduit Dyna-Thread threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. q. For use with Bull Moose Tube EDDY-Lite threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. r. For use with Bull Moose Tube EDDY-Thread threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. t. For use with Western International Forest Products Rapid Thread threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. u. For use with Wheatland Tube WLS threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. v. For use with Wheatland Tube Mega Thread threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS. w. For use with Wheatland Tube MLT threadable Thinwall steel sprinkler pipe in sizes: 114, 112, and 2 in. NPS.
Segmentally welded pipe fittings for use with flexible or rigid grooved pipe couplings, plain end fittings, welded or threaded joints, or flanges. Working pressures of 300 psi (2070 kPa) for non-threadable Thinwall pipe up to 4 in. NPS, Schedules 10 and 40 up to 8 in. NPS, and 250 psi (1725 kPa) for 10 and 12 in. NPS. Prefix 7 in model no. means made from non-threadable Thinwall pipe. Prefix 10 in model no. means made from Schedule 10 pipe. Prefix 40 in model no. means made from Schedule 40 pipe.
FM Approvals
1-347
Product Designation
Fitting Description
7-R1 10-R1, 40-R1 7-R2 10-R2, 40-R2 7-R3 10-R3, 40-R3 7-T3 10-T3, 40-T3 7-T2 10-T2, 40-T2 7-X1 10-X1, 40-X1 7-BT1 10-BT1, 40-BT1 10-F2, 40-F2 7-E9 10-E9, 40-E9 7-E3 10-E3, 40-E3 7-E4 10-E4, 40-E4 7-K9 10-K9, 40-K9
Reducer, Grooved, Concentric Reducer, Grooved, Concentric Reducer, Grooved, Eccentric Reducer, Grooved, Eccentric Reducer, Grooved MPT, Concentric Reducer, Grooved MPT, Concentric Reducing Tee, Grooved Grooved MPT Reducing Tee, Grooved Grooved MPT Tee, Reducing Grooved Tee, Reducing Grooved Cross, Grooved Cross, Grooved Tee, Bullhead, Grooved Tee, Bullhead, Grooved Adaptor Nipple, Grooved Flanged 90 Drain Elbow, Grooved 90 Drain Elbow, Grooved 22.5 Elbow, Grooved 22.5 Elbow, Grooved 11.25 Elbow, Grooved 11.25 Elbow, Grooved End Cap, Drain, Concentric End Cap, Drain, Concentric
114 by 1 through 4 by 3 114 by 1 through 12 by 10 114 by 1 through 4 by 3 114 by 1 through 12 by 10 114 by 12 through 4 by 3 114 by 12 through 12 by 6 114 by 114 by 14 through 4 by 4 by 3 114 by 114 by 12 through 12 by 12 by 10 114 by 114 by 14 through 4 by 4 by 3 114 by 114 by 12 through 12 by 12 by 10 114 through 4 114 through 10 2 by 2 by 212 through 312 by 312 by 4 2 by 2 by 212 through 6 by 6 by 8 112 through 12 114 through 4 114 through 12 114 through 4 114 through 12 114 through 4 114 through 12 112 through 4 112 through 12
Tri-flex Loops The model numbers of the Tri-flex Loops contain a digit, which represents the amount of flex in inches that each assembly will tolerate in each principal plane of motion. The size of each assembly increases in proportion to the amount of flex required for each installation. Consult the manufacturer for overall dimensions of each loop.
Product Designation Nominal Pipe Size, in. Assembly Ends Max Working Pressure, psi (kPa)
Remarks
2-3 4-12
Flanged ends 150 lb Flanged ends 150 lb Flanged ends 150 lb Flanged ends 150 lb Flanged ends Flanged ends
a, b, c a, b, c
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (2070) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205)
2-3 4-12
a, b, c a, b, c
2-3 4-12
a, b, c a, b, c
1-3 4
Threaded ends Male NPT Threaded ends Male NPT Threaded ends Male NPT Threaded ends Male NPT Grooved ends Grooved ends
a, b, c a, b, c
1-3 4
a, b, c a, b, c
2-3 4-12
a, b, c a, b, c
2-3 4-12
a, b a, b, c
2-3 4-12
a, b, c a, b, c
Remarks a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall. c. The digit in the Series number is the amount of flex in inches that the assembly will withstand in each cardinal direction.
FM Approvals
1-348
90 Elbow 90 Elbows
1, 114, 112, 2, 12, 34 112, 134, 11412, 11434, 1141, 1121, 112114, 212, 234, 21, 2114, 2112 1, 114, 112, 2, 12, 34 1, 114, 112, 2, 12, 34 1121, 1341, 1112, 1134, 11114, 11112, 114112, 114134, 11411, 1141114, 1141112, 11411412, 11411434, 1141141, 114114112, 1141142, 112112, 112134, 11211, 1121114, 1121112, 11211412, 11211434, 1121141, 1121142, 11211212, 11211234, 1121121, 112112114, 1121122, 212, 21142, 211212, 211234, 121, 2112114, 2112112, 21 21122, 2212, 2234, 221, 22114, 22112 112, 134 1, 114, 112, 2, 12, 34 112, 134, 11412, 11434, 1141, 1121, 112114, 212, 234, 21, 2114, 2112
1 2, 3 4,
Fig. 109
Cored Plug
1, 114, 112, 2
B&K Industries Inc, 2600 Elmhurst Road, Elk Grove Village IL 60007
Product Designation Fitting Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa)
90
90 Elbows
12
thru 4 5, 6
90R 92
1 2
1 4 12
thru 4 3 thru 4 6
120
Elbow, 45
12
thru 4 5, 6
12 12 12
500 (3445) 300 (2070) 500 (3445) 500 (3445) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 500 (3445) 500 (3445) 300 (2070)
FM Approvals
1-349
Product Designation
Fitting Description
130R
Reducing Tees
1 2 1 4, 3 8 1 4 1 2 3 8 1 2 34 34 14, 38, 12 3 4 1 2 1 2, 3 4 1 1 14, 38, 12, 34 1 12 12, 34, 1 1 34 12, 34, 1 114 12 12, 34, 1, 114 114 34 34, 1, 114 14 1 12, 34, 1, 114, 112 1 114 114 38, 12, 34, 1 112 12 34, 112 112 34 12, 34, 1, 114, 112 112 1 12, 34, 1, 114, 112 112 114 12, 34, 1, 114, 112, 2 112 112 12, 34, 1, 114 2 1 2 2 2 3 4 2 2 1 1, 112, 2 2 114 1, 114, 112, 2 2 112 12, 34, 1, 114, 112, 2 2 2 12, 34, 1, 114, 112 212 112 2, 212 212 2 2, 212 12 212 12, 34, 1, 114, 112, 2 2 3 2 2, 3 3 3 12, 34, 1, 114, 112, 2, 212 4 4 12, 34, 1, 114, 112, 2, 212, 3
1 2 1 2
1 2
500 (3445)
130R
Bullhead Tees
134 180
3 8
500 (3445)
thru 4 5, 6
220 240
12
thru 4
3 8 3 8, 1 2 1 38, 12, 34 114 12, 34, 1 12 12, 34, 1, 114 1 2 12, 34, 1, 114, 112 212 112, 2 3 112, 2, 212 4 2, 3
34
1 2
500 (3445) 500 (3445) 300 (2070) 500 (3445) 500 (3445)
241
Bushing
1 4, 3 8 3 8, 1 2 1 1 2, 3 4 114 12, 34, 1 112 38, 12, 34, 1, 114 2 38, 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 312 212, 3 4 34, 1, 114, 112, 2, 212, 3, 312 5 2, 3, 4 6 2, 212, 3, 312, 4, 5
12 12
1 2 3 4
300 (2070) 500 (3445) 500 (3445) 300 (2070) 500 (3445) 500 (3445) (3445)
291 300
thru 4 thru 4 5, 6
12 12
thru 2 thru 4
12, 34
FM Approvals
1-350
BMI Canada Inc, 3437 Grande Allee Blvd, Boisbriand, Quebec J7H 1H5, Canada
Product Designation Fitting Description Nominal Pipe Size, in. Pressure Rating, psi (kPa)
15027 15028 15204 15205 15206 15207 15208 15209 15304 15305 15306 15307 15308 15309 15327 15328 15331 15332 15333 15335 15340 15343 15404 15405 15406 15407 15408 15409 15420 15436 15437 15438 15440 15442 15448 15451 15452 15453 15454 15455 15457 15458
Reducing Hex Coupling Reducing Hex Coupling 45 Elbow 45 Elbow 45 Elbow 45 Elbow 45 Elbow 45 Elbow 90 Elbow 90 Elbow 90 Elbow 90 Elbow 90 Elbow 90 Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow 90 Reducing Elbow Equal Tee Equal Tee Equal Tee Equal Tee Equal Tee Equal Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee
12
1 3 4 1 1 2
12 34
1 1 1 4 1 1 2 2
12 34
1 1 1 4 1 1 2 2 1 2 3 4
1 1 112 1 1 114 1 1 3 4 1 1 1 2 1 3 4 1 1 1 2 1 114 114 2 114 114 112 114 114 1 114 114 34 114 114 12 114 1 114 1 1 4 1 1
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
FM Approvals
1-351
Product Designation
Fitting Description
15459 15460 15462 15463 15470 15471 15472 15473 15474 15475 15477 15478 15479 15480 15482 15483 15485 15494 15495 15496 15497 15498 15531 15533 15535 15540 15550
Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee Reducing Tee
114 1 34 114 1 12 114 34 1 114 1 112 112 112 2 112 112 114 112 112 1 112 112 34 112 112 12 112 114 2 112 114 1 112 114 34 112 114 12 112 1 112 1 1 2 1 1 112 1 34 112 34 112 2 2 112 2 2 114 221 2 2 3 4 2 2 1 2 2 112 112 2 1 1 2 1 2 1 1 2 1 2 2 1 1 4 2 212
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
Beijing Tian Ning Yi He Pipe System Equipment Co Ltd, No. 2, North Road, Ju Yuan, Ma Pa Ju Yuan Industrial Base, Shunyi District, Beijing, P. R. China
Product Designation Pipe Size, mm Fitting Description Max Working Pressure, psi (kPa)
GCPQT01 GCPQT02 GCPQT03 GCPQT04 GCPQT05 GCPQT06 GCPQT07 GCPQT10 GCPQT11 GCPQT12 GCPQT13
60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 76.1G 60.3 through 219 165.1 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 88.9 33.5T through 219 114.3T 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 60.3, 76.1, 88.9, 108, 114.3, 133, 139.7, 159, 165.1, 219 76.11 60.3 through 219 114.3 114.3 76.1 through 219 114.3
90 Elbow 45 Elbow Straight Tee Reducing Tee 11.25 Elbow Cap Reducer 22.5 Elbow Straight Cross Reducing Cross Eccentric Reducer
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
FM Approvals
1-352
Product Designation
Pipe Size, mm
Fitting Description
Coupolet 300
34
1 1 4 114
1 1 2 2 2 1 2 3 4
China Changchun Rongxia Tube Co Ltd, XinLiCheng Town 54, Village Changchun China 130119
Standard threaded branch outlet connections for attachment to pipe by welding. For use with schedule 10 and 40 steel sprinkler pipe. Requires precutting of hole on pipe. NPT internal threaded branch connection conforming to ANSI B1.20.1.
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
Quick-Let
1 2,
3 4
1-112, 2-212 3-8 1-112, 2, 212, 3-5, 6-8 114-112, 2, 212, 3, 4-5, 6-8 2, 212, 3, 4-5, 6-8 2, 212, 3, 4, 5-6, 8 212, 3, 4, 5, 6-8 3, 4, 5, 6, 8 4, 5, 6, 8 6, 8 1
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
FM Approvals
1-353
Product Designation
Fitting Description
Quick-Let
1 1 4
1 1 2
114-112, 112-2, 2-212, 212-4, 5-8 112, 2-212, 3-4, 5-8 2, 212, 3-4, 5-8 212, 3, 3 12-4, 5, 6, 8 3, 312-4, 5, 6, 8 312, 4, 5, 6, 8 5, 6, 8 6, 8 8 114-112, 112-2, 2-212, 212-4, 5-8 112, 2-212, 3-4, 5-8 2, 212, 3-4, 5-8 12, 3, 2 12-4, 3 5, 6, 8 3, 312 - 4, 5, 6, 8 312, 4, 5, 6, 8 5, 6, 8 6, 8 8
300 (2070)
300 (2070)
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
1 1 4
300 (2070)
1 1 2
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
2 1 2, 3 4 5 6
90 Elbow 45 Elbow 90 Elbow, Short Rad. 45 Elbow, Short Rad. Straight Tee Equal Tee, Short Rad. Reducing Tee, Short Rad. End Cap
114 through 6 114 through 6 2 through 4 2 through 4 114 through 6 2 through 4 3 by 3 by 2 through 4 by 4 by 3 114 through 8
Standard groove-ended fittings for use with grooved couplings. 250 psi (1725 kPa) rated working pressure.
100 101 110 150 90 Elbow 45 Elbow Straight Tee End Cap 8 8 8 8
Standard groove-ended fittings for use with grooved couplings. 175 psi (1205 kPa) rated working pressure.
100S 101S 110S 115S 90 Elbow, Short Rad. 45 Elbow, Short Rad. Equal Tee, Short Rad. Reducing Tee, Short Rad. 6 through 12 6 through 12 6 through 12 6 by 6 by 2 through 8 by 8 by 6
FM Approvals
1-354
Dibu S.L., Ctra. Parla a Pinto, Km 2, 800, Parla (Madrid) E-28980, Spain
Product Designation Fitting Description Nominal Outlet Size, in.
12
Weldolet Type FM
33, 42, 48, 60 33, 42, 48, 60, 76, 89 42, 48, 60, 76, 89
34
Branch connections for attachment to pipe by welding. For use with ISO 4200, DIN 2440 and DIN 2448 steel sprinkler pipe. Requires precutting of hole on pipe. Rated working pressure 20 bar (290 psi).
Ever Metal Industry Co Ltd, 853 Kwang Fu Rd, Pa Teh City, Tao Yuen Hsien Taiwan ROC
Standard grooved-end fittings for use with flexible couplings with Schedule 40 or heavier and Schedule 10S or heavier cut or rolled groove-end pipe. 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
Ductile Iron Screwed Fittings 300 psi (2070 kPa) rated working pressure.
D1 D9 D2 D10 D5 D3 D4 90 Elbows 45 Elbows Tees Caps Couplings Crosses Reducing Elbows 1, 114, 112, 2 1, 114, 112, 2 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 34x12; 1x12, 34; 114x12, 34, 1; 112x34, 1, 114; 2x34, 1, 114, 112 34x12; 1x12, 34 12x12x34, 1; 34x12x12, 34; 34x34x12, 1, 114; 1x12x12, 34, 1; 1x34x12, 34, 1; 1x1x12, 34, 114, 112, 2; 114x12x1, 114; 114x34x34, 1, 114; 114x1x12, 34, 1, 114; 114x114x12, 34, 1, 112, 2; 112x12x112; 112x34x112; 12x1x1, 114, 112; 1 112x114x12, 34, 1, 114, 112, 2; 112x112x12, 34, 1, 114, 2; 2x12x2; 2x34x2; 2x1x112, 2; 2x114x114, 112, 2; 12x12, 34, 1, 114, 112, 2; 2x1 2x2x12, 34, 1, 114, 112 34x12; 1x12, 34; 114x34, 1; 112x34, 1, 114; 2x34, 1, 114, 112
1 2, 3 4, 1 2, 3 4,
D6 D7
D8
Reducing Crosses
Fire-Let
NPT Weldable Branch Outlet Fitting NPT Weldable Branch Outlet Fitting NPT Weldable Branch Outlet Fitting
Fire-Let
34
Fire-Let
1 through 112; 2 through 212; 3 through 8 1 through 112; 2; 212;3 through 5; 6 through 8 114 through 112; 2; 2 1 2; 3; 4 through 5; 6 through 8
FM Approvals
1-355
Product Designation
Fitting
Fire-Let
114
Fire-Let
1 1 2
Fire-Let
Fire-Let
2 1 2
Fire-Let
BSPT Weldable Branch Outlet Fitting BSPT Weldable Branch Outlet Fitting BSPT Weldable Branch Outlet Fitting
12
Fire-Let
34
Fire-Let
Fire-Let
1 1 4
Fire-Let
1 1 2
Fire-Let
Fire-Let
2 1 2
2; 2 1 2; 3; 4 through 5; 6 through 8 2; 2 1 2; 3; 4; 5 through 6; 8 2; 212; 3; 4; 5; 6 through 8 212; 3; 4; 5; 6; 8 1 through 112; 2 through 212; 3 through 8 1 through 112; 2; 212; 3 through 5; 6 through 8 114 through 112; 2 2 1 2; 3; 4 through 5; 6 through 8 2; 2 1 2; 3; 4 through 5 4 through 5; 6 through 8 2; 2 1 2; 3; 4; 5 through 6; 8 2; 1 2; 2 3; 4; 5; 6 through 8 212; 3; 4; 5; 6; 8
Remarks
Series TFL2SMP
2-3 4-12
Flanged ends 150 lb Flanged ends 150 lb Flanged ends 150 lb Flanged ends 150 lb Flanged ends Flanged ends 150 lb
a, b a, b
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205)
Series TFL4SMP
2-3 4-12
a, b a, b
Series TFL8SMP
2-3 4-12
a, b a, b
FM Approvals
1-356
Product Designation
Assembly Ends
Remarks
Series TFL2SMN
1-3 4
Threaded ends Male NPT Threaded ends Male NPT Threaded ends Male NPT Threaded ends Male NPT Grooved ends Grooved ends
a, b a, b
300 (2070) 175 (2070) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205)
Series TFL4SMN
1-3 4
a, b a, b
Series TFL2SVG
2-3 4-12
a, b a, b
Series TFL4SVG
2-3 4-12
a, b a, b
Series TFL8SVG
2-3 4-12
a, b a, b
Remarks a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. b. Min schedule rolled groove pipe to be joined: 6 in. or smaller Schedule 10; 8 in. or larger 0.188 in. (5 mm) wall.
Steel Fittings 22004-08 Standard Coupling (PP) Slip Coupling (PP) 90 Elbow (PP) 90 Elbow, Short Rad. (PP) 90 Elbow (PI) 90 Elbow (II) 90 Elbow, Male (PM)(BSP) Bullhead Tee 45 Elbow (PP) 90Fabr. Elbow, Male (PM)(BSP) 45 Elbow (PI) Straight Tee (PPP) Tee Reducing Branch (PPP) Tee Reducing Branch (PPF)(BSP) 20 through 50
22104-08
20 through 50
20 through 50
32 through 50
20 through 50
20 through 50
2034
20704-08
20 through 50
21004-08
20 through 50
21211-226
21307-321
FM Approvals
1-357
Designation
Product Description
22309-324
2520 through 5040 20 through 50 2034 through 251 2034 through 502
90214-18 21806-9
21707-11
316 S. S. Press-Fit Couplngs. To be installed with Geberit Mapress pressing tools EFP-2, EFP-3, or HCDS only. FM Approved for use with Geberit Mapress Stainless Steel Schedule 5 pipe in wet or dry pipe systems in 25-100 mm nominal sizes, and for use with valve trim and accessories in 20 mm nominal size. Stainless Steel Fittings
32004-11
Standard Coupling (PP) Slip Coupling (PP) 90 Elbow (PI) 90 Elbow (II) 90 Elbow (PP) 90 Elbow (PF)(BSP) 90 Short Rad. El (PP) 90 Elbow, Male (PM)(BSP) 45 Elbow (PI) 45 Elbow (PP) Straight Tee (PPP) Tee Reducing Branch (PPP) Tee Reducing Branch (PPF)(BSP) Reducer (IP) Blind Cap Union Adapter-Female (PF)(BSP) Adapter-Male (PM)(BSP) Adapter-Female (PF)(BSP)
20 through 100
32104-11
20 through 100
20 through 100
20 through 50
20 through 100
20 through 32
30206-08
32 through 50
33835-39
20 through 100
20 through 100
31211-250
252520 through 10010080 202012 through 1001002 2520 through 10080 20 through 100 201 through 502 2012 through 803 2012 through 502
31307-339
32309-348
90224-231 35034-38
31707-24
31805-26
Gentler Industrial Co Ltd, 178-10A Chung Chang Rd, Chung Chang Tsun Ta Liau Shiang Kaohsiung Hsien Taiwan ROC
Standard grooved-end fittings for use with grooved couplings: 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
DUCCO Brand Fittings GT-602* GT-604* 90 Elbow 45 Elbow 114 through 8 114 through 8
FM Approvals
1-358
Product Designation
Fitting Description
114 through 8 114 through 8 2122; 32, 212; 42, 212, 3; 6212, 3, 4; 84, 6
Georg Fischer Fittings GmbH, Mariazeller Straue 75, A-3160 Traisen Austria
Standard malleable iron (W400-05) threaded pipe fittings to ISO 49, and BS EN 10242. Threads in accordance with ISO 7-1 (taper external, parallel internal threads where sealing is achieved on the threads), and ISO 228 (parallel internal threads where sealing is not achieved on the threads). Rated working pressure 450 psi (3100 kPa).
Product Designation
Fitting Description
1 1A 2 2A 3 40 41 50 51 53 54 90 90
Long Sweep Bend Short Sweep Long Sweep Bend Short Sweep Bend Long Sweep Bend 45 Long Sweep Bend 45 Long Sweep Bend 30 Bend 30 Bend 15 Bend 15 Bend Equal Elbow Reducing Elbow
1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
92 92
112, 34, 11412, 34, 1, 11234, 1, 114, 21, 114, 112 12, 34, 1, 114, 112, 2
1238, 3412,
134, 11434, 92 Elbow, Reducing Internal Thread Elbow 45 Elbow 45 Elbow Equal Tee Tee Branch Increasing
1, 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
130
1, 341, 1114, 112, 114112, 2, 1122 1214, 38, 3414, 38, 12, 114, 38, 12, 34, 11438, 12, 34, 1, 11212, 34, 1, 114 212, 34, 1, 114, 112
1234,
450 (3100)
FM Approvals
1-359
Product Designation
Fitting Description
130
450 (3100)
11212, 34, 13412, 34, 1138, 12, 34, 111434, 114121, 143434, 1, 1 114134, 1, 11411412, 34, 1, 1141121, 11212114, 11234114, 11211, 121141, 114, 1 1211212, 34, 1, 114, 1 1122114, 212112, 234112, 21112, 2114112, 2112112, 2212, 34, 1, 114, 112 12, 34, 1
1 2, 3 4,
12, 34, 1 2, 3 4,
1,
114,
240
Reducers
240
Reducers
241
Reducing Bush
241
Reducing Bush
246
Socket
270 280 290 291 291A 300 330 331 340 t 341 2701
Socket Hex Nipple Plug Beaded Plug, Plain, Hollow Plug, Plain Solid Cap Union Flat Seat Union Flat Seat Union Taper Sea Union Taper Seat Socket (Steel)
3412, 112, 34, 1141, 11234, 1, 21 1238, 3412, 34, 1141, 1 112114, 2112 3438, 112, 11412, 34, 11212, 34, 1, 212, 34, 1, 114 1238, 3412, 134, 1141, 112114, 2112 3438, 112, 11412, 34, 11212, 34, 1, 212, 34, 1, 114 1238, 3438, 12, 112, 34, 11412, 34, 1, 11212, 34, 1, 114, 212, 34, 1, 114, 112 12, 34, 1, 114, 112, 2 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4, 1 2, 3 4,
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
450 (3100)
1, 1,
114, 114,
112, 112,
2 2
1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2
450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100) 450 (3100)
FM Approvals
1-360
Hyspan Precision Products Inc, 1685 Brandywine Ave, Chula Vista CA 91911
Ball joints for sprinkler system piping. Can be used singly or in multiples to connect sprinkler systems on mobile structures to stationary water supplies. Requires proper installation geometry for free movement. Consult manufacturer for design information. FM Approved with Type 11/11N packing.
Model Configuration Size
12-4
BB-32000
Straight, one elbow, or double elbow shape. Either male or female NPT ends. Weld Ends Grooved Ends Flanged Ends, 150 lb Flanged Ends, 300 lb
in. NPS
Interfit India Ltd, SF No 112 / 3D, Part Mathapur Road, Kaniyur Village, Coimbatore 641 659, India
Standard groove-ended fittings for use with grooved couplings and grooved pipe as noted.
Product Designation Fitting Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa)
Inter-Fit 100
90 Elbow
500 (3445) 175 (1205) 300 (2070) 500 (3445) 175 (1205) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 500 (3445) 300 (2070) 175 (1205) 300 (2070)
Inter-Fit 101
45 Elbow
Inter-Fit 102
2212 Elbow
2 through 4
105
90 Elbow
F-105-D
90 Drain Elbow
F-106
45 Elbow
F-107
Equal Tee
109
110
F-111
112 112 2, 2 2 212, 2 2 3, 212 212 3, 2 2 4, 212 212 4, 3 3 4, 4 4 6 2 2 1, 114, 112; 3 3 2, 212; 4 4 112, 2, 212, 3, 76 mm; 5 5 3, 4; 139 3, 4; 165 2, 212, 3, 4, 5, 76, 139 mm; 6 6 2, 212, 3, 4, 5, 139 mm 8 8 2, 212, 3, 4, 5, 8 8 6, 76, 139, 165 mm 10 10 3, 4, 5, 5, 6, 8, 165 mm 12 12 4, 5, 6, 8, 10, 165 mm 3, 4, 6, 8
115
Reducing Tee
300 (2070)
125
126
6 4, 8 4, 8 6
FM Approvals
1-361
Product Designation
Fitting Description
F-127
Standpipe Tee
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070)
135
Cross
140
Concentric Reducer
2 114, 112; 212 2; 3 114, 2, 212, 76 mm; 76 mm 114, 112, 2; 4 212, 3, 4, 76 mm 5 2, 212, 3, 4, 76 mm; 139 2, 212, 3, 4, 76 mm 6 2, 212, 3, 4, 5, 76, 139 mm 165 mm 2, 3, 4, 76, 139 mm 8 3, 4, 5, 6, 76, 139 mm 10 3, 4, 5, 6, 8, 139, 165 mm; 12 4, 6, 8, 10, 165 mm 2 1, 114, 112; 212 1, 114, 112, 2; 76 1, 114, 112, 2; 3 1, 114, 112, 2, 212; 4 1, 114, 112, 2, 212, 3; 6 1, 114, 112, 2, 212, 3 114 through 8 in. 10-12, 165 mm 14, 16
140 TM
300 (2070)
150
End Cap
F-155
End Cap
212-4
500 (3445) 300 (2070) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 500 (3445) 500 (3445) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 500 (3445)
63
90 Red. Elbow
1 12 to 212 2
64
Tee
12-2
212-4
65
Reducing Tee
3 4
34 12 to 2 114 2
12-2
66
Cross
67
Cap
12-2
212-3
68
Fem. Coupler
12
to 4
69
Hex Nipple
12
to 4
70
Hex Bushing
12
38 to 112 114
12-4
71
Union
72
12-2
73
12-2
FM Approvals
1-362
Product Designation
Fitting Description
74
Reducing Socket
3 4
12 to 212 2
75
Hex Reducer
1 1 2, 3 4
70, 71
Reducer
70, 71
Reducer
72
Reducer with one grooved end and one male NPT end
80 30
15 55 35
Straight Tee Hose Valve Tee, NPT Female Threaded Outlet Reducing on Run Tee
50
Bullhead Tee
50
Bullhead Tee
60 65 85, 86 85, 86
Straight Cross Reducing Cross Straight Tee with Female NPT Side Outlet Straight Tee with Reducing Female NPT Side Outlet
2122; 32, 212; 3122, 212, 3; 42, 212, 3, 312; 52, 212, 3, 312, 4; 62, 212, 3, 312, 4, 5; 82, 212, 3, 312, 4, 5, 6; 2122; 32, 212; 3122, 212, 3; 42, 212, 3, 312; 52, 212, 3, 312, 4; 62, 212, 3, 312, 4, 5; 82, 212, 3, 312, 4, 5, 6 212 through 8 212212114, 112, 2; 33114, 112, 2, 212; 312312114, 112, 2, 212, 3; 44114, 112, 2, 212, 3, 312; 55114, 112, 2, 212, 3, 312, 4; 66114, 112, 2, 212, 3, 312, 4, 5; 88114, 112, 2, 212, 3, 312, 4, 5, 6 114 through 8 4212; 6212 2122212; 323; 32123; 3122, 212, 3312; 42, 212, 3, 3124; 52, 212, 3, 312, 45; 62, 212, 3, 312, 4, 5,6; 32, 212, 3, 312, 4, 5, 68 22212, 3, 312, 4, 5, 6, 8; 21223, 312, 4, 5, 6, 8; 2122123, 312, 4, 5, 6, 8; 32312, 4, 5, 6, 8; 3212312, 4, 5, 6, 8; 33312, 4, 5, 6, 8; 31224, 5, 6, 8; 3122124, 5, 6, 8; 31234, 5, 6, 8; 3123124, 5, 6, 8; 425, 6, 8; 42125, 6, 8; 435, 6, 8; 43125, 6, 8; 445, 6, 8; 526, 8; 52126, 8; 536, 8; 53126, 8; 546, 8; 556, 8; 62, 212, 3, 312, 4, 5, 68 212 through 8 212-82-82-82-8 212 through 4 2121-2; 31-212; 3121-3;
FM Approvals
1-363
Product Designation
Fitting Description
85, 86
Reducing on Run and or Outlet Tee with Female NPT Side Outlet
EL
EL
40
90 Elbow 60 Elbow 45 Elbow 30 Elbow 2212 Elbow 912 Elbow 1114 Elbow Reducing on Run and Outlet Tee
41-312; 51-4; 61-4 21221-212; 321-3; 32121-3; 31221-312; 3122121-312; 31231-312; 42-3121-4; 52-41-4; 62-51-4; 82-61-4 114 through 8
RT1-RT5
Riser Tee
21222; 322, 212; 32122, 212; 3122-32-3; 42-3122-312; 52-42-4; 62-52-5; 82-62-6 212 through 8*
*All size riser tees have a rated working pressure of 250 psi (1725 kPa).
Branch connections for attachment to pipe by welding. For use with Schedule 10S or heavier pipe unless otherwise noted. Requires precutting of hole in pipe. Rated working pressure 300 psi (2070 kPa)
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in.
Model A
Shape Nipple
1 1 1 4 1 1 2 2 2 1 2 3 4 5 6
10RG*
112, 2, 212, 3, 4, 5, 6, 8
Cut Grooved Outlet Roll Grooved Outlet Male Thread Outlet 3712 Bevel for Butt Welding
114, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8
FM Approvals
1-364
Standard groove-ended fittings for use with flexible couplings. 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
2 2 2 2
6 6 6 6
JFE Pipe Fitting Mfg Co Ltd, 153 Tajime-Cho, Kishiwada Osaka, Japan
Product Designation Nominal Pipe Size, in. Fitting Description Remarks Max Working Pressure, psi (kPa)
901 902 903 7041 7110 7111 7112 7113 7120 7121
Short Radius 90 Elbow Grooved Short Radius 45 Elbow Grooved Shurjoint Radius Tee Grooved Flange Grooved 90 Elbow Grooved 45 Elbow Grooved 2212 Elbow Grooved 1114 Elbow Grooved Tee Grooved Reducing Tee Grooved Cross Grooved Concentric Reducer Eccentric Reducer
a, b, c
2 through 8 2 through 8 114 through 8 2112, 2122, 32, 3212, 42, 4212, 43, 63, 64 2, 212, 3, 4, 5, 6 2122, 32, 3212, 42, 4212, 43, 54, 62, 63, 64, 65, 84, 86 2122, 32, 3212, 42, 4212, 43, 64, 65, 84, 86 114 through 8 212, 3, 4, 5, 6
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
7135 7150
7151
FM Approvals
1-365
Product Designation
Fitting Description
Remarks
DI, Reducing Couplings DI, Reducing Coupling Extension Pieces DI, Crosses DI, Straight Coupling DI, Caps DI, Hex. Bushings
3412, 134, 112, 1141, 11434, 11412, 112114, 1121, 11234, 2112, 21, 234, 2122 12, 34, 1, 114, 112, 2, 212 343412, 1134, 1112, 1341, 13434, 13412, 1121, 1141141, 11411434, 11411412, 1141114, 11411, 114134, 114112, 11114, 112112114, 1121121, 11211234, 11211212, 112114112, 1121141, 11211434, 11211412, 1121112, 11211, 112134, 112112, 11112, 14114112, 1141112, 1 22112, 22114, 221, 2234, 2212, 21122, 2112112, 21121, 211234, 211212, 21142, 212, 1121122, 1121142, 212234, 22212 134, 112 12112 34112
300 (2070)
300 (2070)
L, L,
122 342
L, L
1,
114,
112,
1141,
134, 112, 1141, 11434, 11412, 112114, 1121, 11234, 11212, 2112, 2114, 21, 234, 212 1141, 112114, 1121, 2112, 2114 12, 34, 1, 114, 112, 2
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a. 212, 4 in. British Standard BS 1387 medium or heavy pipe. b. Min schedule cut groove pipe to be joined: 8 in. or smaller Schedule 40. c. Min schedule rolled groove pipe to be joined: 8 in. or smaller Schedule 10.
Jinan Meide Casting Co Ltd, No. 3 Nanmen Road, Pingyin Jinan Shandong 250400, China
Product Designation Fitting Description Nominal Pipe Size, in. Max Working Pressure, psi (kPa)
90
90 Elbow
300 (2070) 500 (3445) 500 (3450) 300 (2070) 500 (3450)
90
114, 112, 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 6, 8 76, 139.7, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2, 212, 3, 4, 6, 8 76, 139.7, 165 mm
90S
120
130
500 (3450)
130S
300 (2070)
FM Approvals
1-366
Product Designation
Fitting Description
130R
2112, 31, 112, 2, 212, 41, 2, 212, 3, 52, 3, 4, 62, 212, 3, 4, 5, 82, 3, 4, 5, 6 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 61, 2, 212, 3, 4, 5, 8212, 3, 4, 5, 6 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 8212, 3, 4, 5, 6 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 12, 3, 4, 5, 6 82 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2, 212, 3, 4, 5, 6, 8 76.1, 165 mm 10, 12, 139.7 mm
500 (3450)
180
500 (3450)
240
500 (3450)
240N
500 (3450)
240W
500 (3450)
300
500 (3450) 500 (3450) 300 (2070) 500 (3450) 500 (3450) 500 (3450) 500 (3450)
321G
35C
12, 34,
35CP
12, 34,
35E
12, 34,
35F
12, 34,
35HB
500 (3450)
35RC
500 (3450)
35RE
500 (3450)
FM Approvals
1-367
Product Designation
Fitting Description
35RT
343412, 1 341234, 12
500 (3450)
1112, 34, 114, 112 13434, 1 1121 1411412, 34, 1, 112, 2 1 14112, 34, 1, 114, 112 1 11434114 11412114 11211212, 34, 1, 1, 114, 2 11211412, 34, 1, 114, 112 112112, 34, 1, 114, 112 11234114, 112 11212114, 112 12, 34, 1, 114, 112, 212 22 211212, 34, 1, 114, 112, 2 21142 212 21221234, 1, 114, 112, 2, 3 35RX D.I. Reducing Cross, Threaded 1141, 1121, 21 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
35SP
1 2, 3 4,
1, 114, 112, 2
35T
12, 34,
35U
1, 114, 112, 2
35X
1, 114, 112, 2
37E
12, 34,
37F
12, 34,
37RC
112, 34 21 112, 34, 11412, 34, 1, 11212, 34, 1, 114, 212, 34, 1, 114, 112, 1234, 1, 114, 112, 2 2 11212, 34, 1, 13412, 34, 1, 1112, 34, 114, 11141, 11411412, 34, 1, 112, 2, 114112, 34, 1, 114, 112,, 11434114, 11412114, 1211212, 34, 1, 1, 114, 2, 1 11211412, 34, 1, 114, 112, 112112, 34, 1, 114, 112, 2, 11234114, 112, 11212114, 112, 2212, 34, 1, 114, 112, 211212, 34, 1, 114, 112, 2, 211412, 1, 114, 112, 2, 2134, 1, 114, 2, 22212, 21221212, 34, 1, 114, 112, 2, 2114212, 21212, 234212, 212122, 212
1 2, 3 4,
37RE
37RT
300 (2070)
37T
1, 114, 112, 2
300 (2070)
Model No.
Description
90
90 Elbows
thru 4
500 (3445)
FM Approvals
1-368
Model No.
Description
thru 43 thru 4 6
120
Elbow, 45
1 2
thru 4 5, 6
1 2 1 2 1 2
130R
Reducing Tees
300 (2070) 500 (3445) 500 (3445) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 500 (3445) 500 (3445) 300 (2070) 500 (3445)
130R
Bullhead Tees
1114, 38, 12, 34 11212, 34, 1 13412, 34, 1 1141212, 34, 1, 114 1143434, 1, 114 114112, 34, 1, 114, 112 1411438, 12, 34, 1 1 1121234, 112 123412, 34, 1, 114, 112 1 112112, 34, 1, 114, 112 11211412, 34, 1, 114, 112, 2 11211212, 34, 1, 114 2122 2342 211, 112, 2 21141, 114, 112, 2 211212, 34, 1, 114, 112, 2 2212, 34, 1, 114, 112 2121122, 212 21222, 212 21221212, 34, 1, 114, 112, 2 322, 3 3312, 34, 1, 114, 112, 2, 212 12, 34, 1, 114, 112, 2, 212, 3 44 383812 121234, 1 34341 11114, 112, 2 114114112, 2 1121122 22212 12 thru 2
1 2 1 2
500 (3445)
thru 4 thru 4 5, 6
180R
Reducing Cross
3412
134 11434, 1 11234, 1/114 234, 1/114, 112 121, 114, 112, 2 2 31, 114, 112, 2, 212 4212, 3 220 240 Coupling Reducing Coupling
1 2
500 (3445) 500 (3445) 500 (3445) 300 (2070) 500 (3445)
thru 4
1238) 3438, 12 138, 12, 34 11412, 34, 1 11212, 34, 1, 114 212, 34, 1, 114, 112 212112, 2 3112, 2, 212 42, 3
FM Approvals
1-369
Model No.
Description
241
Bushing
500 (3445)
11412, 34, 1 11238, 12, 34, 1, 114 238, 12, 34, 1, 114, 112 21212, 34, 1, 114, 112, 2 312, 34, 1, 114, 112, 2, 212 312212, 3 434, 1, 114, 112, 2, 212, 3, 312 52, 3, 4 62, 212, 3, 312, 4, 5
300 (2070)
280
Hex Nipple
1 2
thru 212
500 (3445) 500 (3445) 500 (3445) 300 (2070) 500 (3445) 500 (3445) 500 (3445) 300 (2070) 500 (3445) 500 (3445) 500 (3445)
291
1 2
thru 4
291-4
4 5, 6
291N
1 2
thru 4
291S
1 2
thru 4
300
Cap
1 2
thru 4 5, 6
321
Flange
1 2
thru 2
342
Unions
1 2
thru 4
529
Extension Piece
1 2, 3 4,
ZMBL90xx ZMGL90xx
90 Elbows
12
thru 4 5, 6
Reducing Elbows, 90
1214
thru 43
500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa)
Street Elbows, 90
12
thru 4 6
ZMBL45xx ZMGL45xx
Elbow, 45
12
thru 4 5, 6
12 12 12
FM Approvals
1-370
Product Designation
Fitting Description
ZMBTRxxxx ZMGTRxxxx
Reducing Tees
ZMBTRxxxxxx ZMGTRxxxxxx
Bullhead Tees
1114, 38, 12, 34 11212, 34, 1 13412, 34, 1 141212, 34, 1, 114 1 1143434, 1, 114 114112, 34, 1, 114, 112 11411438, 12, 34, 1 1121234, 112 1123412, 34, 114, 112 112112, 34, 1, 114, 112 11211412, 34, 1, 114, 112, 2 11211212, 34, 1, 114 2122 2342 211, 112, 2 21141, 114, 112, 2 211212, 34, 1, 114, 112, 2 2212, 34, 1, 114, 112 21222, 212 1221212, 34, 1, 114, 112, 2 2 3312, 34, 1, 114, 112, 2, 212 4412, 34, 1, 114, 112, 2, 212, 3 121234, 1 34341 11114, 112, 2 14114112, 2 1 22212 1 2
12
thru 4 5, 6
12
thru 4
1238 3438, 12 138, 12, 34 11412, 34, 1 11212, 34, 1, 114 212, 34, 1, 114, 112 212112, 2 3112, 2, 212 42, 3 1214, 38 3438, 12 112, 34 11412, 34, 1 11238, 12, 34, 1, 114 238, 12, 34, 1, 114, 112 1212, 34, 1, 114, 112, 2 2 312, 34, 1, 114, 112, 2, 212 3123 434, 1, 114, 112, 2, 212, 3 52, 3, 4 62, 212, 3, 4, 5 12 thru 4
500 psi (3445 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa)
ZMBBUxxxx ZMGBUxxxx
Bushing
ZMBPLxx ZMGPLxx ZMBPL11B ZMGPL11B ZMBPL12 ZMGPL12 ZMBPLSSxx ZMGPLSSxx ZMBCAxx ZMGCAxx
4 5
1 thru 2
12
thru 4 5, 6
12 12 12
300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 300 psi (2070 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa) 500 psi (3445 kPa)
FM Approvals
1-371
Merit Manufacturing, Division of Anvil International Inc, 110 Corporate Dr, Suite 10, Portsmouth NH 03801
Product Designation Fitting Description Nominal Pipe Size, in.
The above fittings have a 500 psi (3445 kPa) rated working pressure.
Product Designation Fitting Description Nominal Pipe Size, in.
112 134
The above fittings have a 300 psi (2070 kPa) rated working pressure.
Product Designation Fitting Description Notes Nominal Outlet Size, in.
1 2 3 4
a, b, c, d, e, f, g, h ;;
114 through 8 114 through 8 114 through 8 112 through 8 2 through 8 212 through 8 3 through 8 4 through 8 5 through 8
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 300 psi (2070 kPa). For use with pipes as noted above, in sizes as appropriate.
Merit Weld-Miser Tee-Let Type A NPT Weldable Branch Outlet Fitting j
1 2 3 4
1 114112
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 175 psi (1205 kPa). For use with pipes as noted above, in sizes as appropriate.
Merit Tee-Let Type C Grooved Branch Outlet Fitting a, b, c, d, e, f, g, h a, b, c, d, e, f, g, h a, b, c, d, e, f, g, h a, b, d, g, h a, b, d, g, h a, b, d, g, h a, b, d, g, h a, b, g, h a, b, g, h a, b, g, h a, b 1 114 112 2 212 76.1 mm 3 4 139.7 mm 5 6 114 thru 8 112 thru 8 2 thru 8 212 thru 8 3 thru 8 88.9, 114.3, 139.7, 141.3, 168.3, 219.1 mm 4 thru 8 5, 6, 8 168.3, 219.1 mm 6, 8 8
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 300 psi (2070 kPa). For use with pipes as noted above, in sizes as appropriate. Merit Tee-Let Type C Grooved Branch Outlet Fitting j 1 114 112 114-112, 2 112, 2 2
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 175 psi (1205 kPa). For use with pipes as noted above, in sizes as appropriate.
a, b, c, d, e, f, g, h
FM Approvals
1-372
Product Designation
Fitting Description
Notes
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 300 psi (2070 kPa). For use with pipes as noted above, in sizes as appropriate. Merit Tee-Let Type C/R Roll Grooved Weldable Branch Outlet Fitting j 114 112 112, 2 2
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 175 psi (1205 kPa). For use with pipes as noted above, in sizes as appropriate.
Merit Tee-Let Type RW NPT Weldable Branch Outlet Fitting a, b, c, d, e, f, g, h
1 2 3 4
114 through 8 114 through 8 114 through 8 112 through 8 2 through 8 212 through 8
1 114 112 2
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 300 psi (2070 kPa). For use with pipes as noted above, in sizes as appropriate.
Merit Tee-Let Type RW NPT Weldable Branch Outlet Fitting j
1 2 3 4
1 114 112
Branch connections for attachment to pipe by welding. Requires precutting of hole on pipe and removal of coupon. Rated working pressure 175 psi (1205 kPa). For use with pipes as noted above, in sizes as appropriate.
Notes: a. For use with Sch. 10 and 40 pipe. b. For use with Allied XL in sizes: 1, 114, 112, 2, 212 and 3 in. NPS, BLT in sizes: 1, 114, 112 and 2 in. NPS, Dyna-flow in sizes: 114, 112, 2, 212, 3, 4, 6 and 8 in. NPS, Super-flo pipe in sizes: 1, 114, 112, 2, 212, 3 and 4 in. NPS. c. For use with Welded Tube Berkeley LLC Steady-flow pipe in sizes: 114, 112 and 2 in. NPS. d. For use with Bull Moose Tube EDDY-flow pipe in sizes: 114, 112, 2, 212, 3 and 4 in. NPS. e. For use with IDOD Systems Gal-flo and Gal-7 pipe in sizes: 114, 112 and 2 in. NPS. f. For use with Youngstown Tube Fire-flo pipe in sizes: 112 and 2 in. NPS. g. For use with Northwest EZ-flow pipe in sizes: 3 and 4 in. NPS (300 psi), and 6 in. NPS (175 psi only). h. For use with Tex-Tube Tex-flow pipe in sizes: 212, 3, 4 and 6 in. NPS. j. For use with Sch. 5 pipe at 175 psi (1205 kPa) in sizes: 1, 114, 112, and 2 in. NPS
Modgal Metal (99) Ltd, Box 63, Rosh Pina 12000, Israel
QUIKCOUP standard grooved ended fittings for use with grooved couplings.
Product Designation Fitting Description Nominal Pipe Size, in./ mm Max Working Pressure, psi (kPa)
Remarks
02 02
End Cap (Blind) End Cap (Blind) End Cap (34 in. NPT Tapped Vent Hole) End Cap (Blind) End Cap (Tapped 112 in. BSP) 45 Elbow Tee Tee Tee 90 Elbow 90 Elbow 90 Elbow
114 through 8 10
500 (3445) 175 (1205) 500 (3445) 290 (2000) 290 (2000) 500 (3445) 500 (3445) 290 (2000) 200 (1380) 500 (3445) 290 (2000) 200 (1380)
02D
3 through 8 76, 108, 133, 140 159, 165 mm 76, 108, 133, 159, 165 mm 112 through 8 114 through 8 76, 108, 159 mm 10 114 through 8 76, 108, 159 mm 10
FM Approvals
1-373
Product Designation
Fitting Description
Remarks
06D
3, 4, 6, 8 112114; 2112 32, 212; 42, 3 62, 3, 4; 84, 6 108 7660 mm, 11476 mm, 14089, 114 mm, 16560, 89 mm, 114, 140 mm, 168140 mm 219140 mm 139 by 89, 114; 168 by 60, 89, 114, 139; 219 by 89, 114, 139, 168 mm 1121
15
15
15
Concentric Reducer
500 (3445)
15
Concentric Reducer Concentric Reducer, Grooved Ends Reducing Adapter, Groove Female BSP Thread Sprinkler Adapter, Groove Female NPT Thread Elbow, Groove Female BSP Thread
15
24
250 (1725) 175 (1205) 300 (2070) 250 (1725) 500 (3450)
25
1121
26
2112 112112 22 2 Gr.2 BSP Male Thread 60, 76, 89, 114, 139, 165, 168, 219, 273, 324 mm 2122122; 332; 442; 44212; 443; 66112, 2, 212, 3, 4 11476 mm 139 by 60, 89, 114; 168 by 60, 89, 114, 139, 219 by 60, 89, 114, 139, 168 mm 42, 48, 60, 76, 89, 114, 139,165, 168, 219, 273, 324 mm 60, 76, 89, 114, 139, 165, 168, 219 mm 48, 60, 76, 89, 114, 140, 165, 168 mm 48, 60, 76, 89, 114, 140, 165, 168 mm 60, 76, 89, 114, 139, 165, 168, 219 mm 60, 76, 89, 114, 139, 165, 168, 219 mm 273, 324 mm 3, 4 6, 8, 10 165 mm 112, 2, 3, 4, 6, 8
28
45
55
500 (3445)
55
55
64
45 Elbow, Grooved Ends Short Radius Tees, Grooved Ends Short Radius Equal Tee Short Radius 90 Elbow 90 Short Elbow, Grooved Ends
500 (3450) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 500 (3450) 300 (2070) 500 (3445) 175 (1205) 175 (1205) 300 (2070)
65 Style 65 Style 66 66
91
91 91 91 Elbow 2212
g g g
FM Approvals
1-374
Product Designation
Fitting Description
Remarks
Elbow 2212 Elbow 1114 Elbow 1114 280 281 282 285 286 288
Segmentally Welded Segmentally Welded Segmentally Welded Coupling, Plain End Single Coupling, Plain Thread End Cap Equal Tee, Plain End Elbow, 90, Plain End Quik-T, Plain End Outlet
76, 140 mm 112, 2, 3, 4, 6, 8 76, 140 mm 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112, 2 1, 114, 112 1, 114, 112 31, 114, 112 41, 114, 112, 2 112, 34, 1 11412, 34, 1 11212, 34, 1 212, 34, 1
a, b, c, d, e a, b, c, d, e, f a, b, c, d, e a, b, c, d, e a, b, c, d, e
300 (2070) 300 (2070) 300 (2070) 232 (1600) 232 (1600) 232 (1600) 232 (1600) 232 (1600) 232 (1600) 232 (1600)
289
a, b, c, d, e, f
Remarks: a. b. c. d. e. f. g. Approved for use with Schedule 10 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. Approved for use with Schedule 40 steel sprinkler pipe in sizes: 1, 114, 112, and 2 in. NPS. Approved for use with DIN 2458 steel sprinkler pipe. Approved for use with ISO 65 steel pipe in sizes: 1, 114, 112, and 2 in. NPS. Approved when supplied with EPDM gasket. Approved when supplied with ISO 7/1 threaded connections. Adapters are used for connecting traditional PN16 flanges to grooved piping systems.
National Fittings Inc, 295 East Swedesford Road #280, Wayne PA 19087-1462
Nominal Pipe Run Sizes, in. Outlet Size, in./ mm
Series T3F-NPT 1 1 4 1 1 2 2 212 3, 4, 5, 6, 8 Series T3F-BSP 114 1 1 2 2 212 3, 4, 5, 6, 8 Series T3G 1 1 4 1 1 2 2 212 3 4 5 6 8 76.1 mm 165.1 mm
1 1, 114 12, 34, 1, 114, 112 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2, 212
12, 34,
12, 34,
1 1, 114 12, 34, 1, 114, 112 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2, 212
12, 34,
12, 34,
1 1, 114 1, 114, 112 1, 114, 112, 2 1, 114, 112, 2, 212 1, 114, 112, 2, 212, 3, 76.1 mm 1, 114, 112, 2, 212, 3, 4, 76.1 mm 1, 114, 112, 2, 212, 3, 4, 5, 76.1 mm 1, 114, 112, 2, 212, 3, 4, 5, 6, 76.1 mm, 165.1 mm 1, 114, 112, 2, 212 1, 114, 112, 2, 212, 3, 4, 5, 6, 76.1 mm
All 300 psi (2070 kPa) rated working pressure. Standard groove-ended fittings for use with grooved couplings and grooved pipe as noted. FireShield 300 Grooved End Fitting Product Line
FM Approvals
1-375
Product Designation
Fitting Description
100
90 Elbow
114 through 8 10, 12, 76, 165 mm 14 through 8 1 10, 12 in., 76, 165 mm 14 through 6 1 212 through 6 114 through 6 114 through 6 114 through 8, 10, 12 in., 76, 165 mm 1121122, 22212, 223, 2122123, 224, 2122124, 334, 446 22112, 332, 33212, 442, 44212, 443, 553, 554, 662, 66212, 663, 664, 882, 883, 884, 886 4 by 212, 3 6 by 212, 3 8 by 212, 3 114 through 6 8
101
45 Elbow
111
500 (3445) 175 (1205) 500 (3445) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 175 (1205) 500 (3445) 175 (1205) 300 (2070)
115
Reducing Tee
300 (2070)
F-127
Standpipe Tee
135
Cross
140
Concentric Reducer
2122, 32, 3212, 42, 4212, 43, 53, 54, 62, 6212, 63, 64, 8212, 83, 84, 86 10, 12 in. 114 through 8 10, 12 in. 76, 165 mm 14 through 6 1
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070)
150
End Cap
155
Cap
Slip-on and Blind Flanges. 4-12 in. sizes in accordance with AWWA-C207.
PFS PFS PFB PFR Slip-on Flange (thin) Slip-on Flange Blind Flange Reducing Slip on Flanges 2-3 2-12 2-12 4212 43 63 64 84 86 175 (1205) 175 (1205) 175 (1205) 175 (1205)
Standard threaded pipe fittings conforming to ASTM A-126. Grade A cast iron. ANSI B2.1 NPT internal threads. Rated working pressure 175 psi (1205 kPa).
Product Designation Fitting Description Nominal Pipe Size, in.
through 2 through 2 through 2 through 2 112, 34; 11412, 34, 1; 1121, 114; 12, 34, 1, 114, 112 2
1 1 1 1
FM Approvals
1-376
Product Designation
Fitting Description
Reducing Tee
Reducing Coupling
1121, 1341; 1112, 34, 114, 112; 114112, 34, 1, 114; 11411412, 34, 1, 112, 2; 112112, 34, 1, 114, 112; 11211412, 34, 1, 2; 11211212, 34, 1, 114, 2; 212, 21142; 211212, 34, 1, 114, 112, 2; 2212, 34, 1, 114, 112 112, 34
Standard threaded pipe fittings conforming to ASTM A-536 (Grade 65-45-12) ductile iron, ANSI B2.1 taper threads according to NPT. Rated working pressure 300 psi (2070 kPa).
Product Designation Fitting Description Nominal Pipe Size, in.
Style 61 Style 63
Style 69 Style 60
through 2 112, 34; 11412, 34, 1; 11212, 34, 1, 114; 2 12,34, 1, 114,112; 12 through 2 12 through 2 112, 34; 114112, 34, 1; 11412, 34, 1; 11211412, 34, 1, 114; 11212, 34, 1, 114; 212, 34, 1, 114, 112; 2112114, 112, 2 112, 34; 1141 1121, 114; 21, 114, 112; 12 through 2 12 through 2 12 through 2
12
North Alabama Pipe Corp, New Industrial Park, Box 750, Guntersville AL 35976
NAP300 Welded Outlets. Rated working pressure 300 psi (2070 kPa).
Product Designation Nominal Outlet Size, FNPT
1 2, 3 4 1, 114 1 1 2 2 2 1 2
NAP300
Qingdao V-Cart Piping Systems Co Ltd, JuiZhao Road, NanGuan Industry Zone, JiaoZhou City, Qingdao, China
Figure Designation Product Description Nominal Pipe Size, in./ mm Pressure, bar (psi)
2, 3, 57, 76 100 90 Elbow 4, 108 5, 6, 8, 133, 139, 141, 159, 165 2, 3, 57, 76 101 45 Elbow 4, 108 5, 6, 8, 133, 139, 141, 159, 165 110 112 Straight Tee Equal cross 2 through 8 57, 76, 108, 133, 139, 141, 159, 165 2 through 6 57, 76, 108, 133, 139, 141, 159, 165
FM Approvals
1-377
Figure Designation
Product Description
2 by 114 through 4 by 3 140G Concentric Reducers G by G 139 by 2 through 12 by 10 in. 2 by 12 through 4 by 3 133 by 1 through 165 by 4 in. 2 by 12 through 4 by 3 133 by 1 through 165 by 4 in. 2 through 12 in., 76, 108, 133, 139, 159, 165 mm
140T
140T
190
FlangeGroove Adapter
13062 130715 13072 130724 130915 13092 130924 130925 13093 131115 13112 131124 131125 13113 13114 13115 13132 131324 13133 13134 13135 13136 13163 13164 13165 13166 13168 13194 13196 13198 131190
22 3112 32 32 4112 42 42 4212 43 6112 62 62 6212 63 64 65 82 82 83 84 85 86 103 104 105 106 108 124 126 128 1210
Rigid Industries Co Ltd, 8 Mei-Chung Rd, Niao-Song Kaohsiung Hsien, 83301 Taiwan
The following fittings are suitable for use on Schedule 10 and 40 pipe.
Product Designation Fitting Description Nominal Outlet Size, in.
1 2
701
3 4
1 1 1 4 1 1 2 2 2 1 2 3 4
1-112, 2-212, 3-8 1-112, 2, 212, 3-5, 6-8 114-112, 2, 212, 3, 4-5, 6-8 2, 212, 3, 4-5, 6-8 2, 212, 3, 4, 5-6, 8 212, 3, 4, 5, 6, 8 3, 4, 5, 6, 8 4, 5, 6, 8 5, 6, 8
300 (2070)
FM Approvals
1-378
Product Designation
Fitting Description
702
2 2 1 2 3 4 6 8 114 1 1 2 2 2 1 2 3 4
212, 3, 4, 5, 6, 8
300 (2070)
73
175 (1205)
SCE Company Ltd, Unit E&F, 20/F, CDW Building, 388 Castl Peak Road, Tsuen Wan, N.T., Hong Kong
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Working Pressure, psi (kPa)
AQUILA Model 90 AQUILA Model 120 AQUILA Model 120 AQUILA Model 130 AQUILA Model 130 AQUILA Model 130R
90 Elbow, Grooved Ends 45 Elbow, Grooved Ends 45 Elbow, Grooved Ends Equal Tee, Grooved Ends Equal Tee, Grooved Ends Reducing Tee, Grooved Ends
114, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2112, 31, 112, 2, 212, 41, 2, 212, 3, 52, 3, 4, 62, 212, 3, 4, 5, 82, 3, 4, 5, 6 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 61, 2, 212, 3, 4, 5, 8212, 3, 4, 5, 6 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 8212, 3, 4, 5, 6 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 8212, 3, 4, 5, 6 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2, 212, 3, 4, 5, 6, 8 76.1, 165 mm
500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450)
Equal Cross, Grooved Ends Equal Cross, Grooved Ends Concentric Reducer, Grooved Ends
500 (3450)
500 (3450)
AQUILA Model 300 AQUILA Model 300 AQUILA Model 321G AQUILA Model 321G
Grooved End Cap Grooved End Cap FlangeGroove Adapter FlangeGroove Adapter
SPT Metal Corp, 19-1 Da Yeh St, Da Liao Hsiang, Kaohsiung Hsien, Taiwan ROC
Cast Grooved Fittings.
Product Designation Fitting Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
310 310
90 Elbow 90 Elbow
a a
FM Approvals
1-379
Product Designation
Fitting Description
Remarks
310 310
90 Elbow 90 Elbow Stainless Steel 45 Elbow 45 Elbow 45 Elbow Stainless Steel Grooved 22.5 Elbow Equal Tee Equal Tee Equal Tee Tee Stainless Steel Reduced Tees Grooved Reducing Tee Stainless Steel 2, 2,
20, 24 3, 4 5, 6, 8 212,
175 (1205) 300 (2070) 300 (2070) 200 (1380) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 200 (1380) 300 (2070) 300 (2070) 300 (2070)
a b
a a b
a a a a b
325 325
2x1 through 8x6 3x2, 4x114, 4x112, 4x2, 4x212, 6x112, 6x2, 6x 212, 6x4 2, 212, 3, 4, 5, 6, 8 2x1 through 12x10 114 1 1 4, through 12 112,, 2 1 2, 3x114, 3x112,
a b
Grooved Cross Concentric Reducers End Cap Grooved Short Radius 90 Elbow Grooved Short Radius 45 Elbow Grooved Short Radius Tee
2, 3, 4, 5, 6, 8
a a a a
3311
300 (2070)
3320
62
a. Ductile iron material b. Stainless steel material
Flange Adapter
Shanghai Vision Mechanical Joint Co Ltd, Jinlan Road, Loutang Industrial Park, Jiading District, Shanghai 201807 PRC
Product Designation Fitting Description Nominal Pipe Size, in./ mm Rated Working Pressure, psi (kPa) Remarks
002
Short Radius 90 Elbow 90 Elbow 45 Elbow 45 Elbow 22.5 Elbow 22.5 Elbow Short Radius Equal Tee Cap Cap
114, 112, 2, 212, 3, 4, 6, 8 45, 57, 76, 108, 133, 140, 159, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 76, 140, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 57, 76, 108, 133, 140, 159, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 45, 57, 76, 108, 133, 140, 159, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 114, 112, 2, 212, 3, 4, 6, 8 57, 76, 108, 133, 140, 159, 165 mm
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
FM Approvals
1-380
Product Designation
Fitting Description
Remarks
008
008
Concentric Reducer
009
009
009I
009I
Short Radius Equal Cross Equal Cross Equal Cross Reducing Branch Tee
112 114 2 114, 112 114, 112, 2 3 114, 112, 2, 212 4 114, 112, 2, 212, 3 6 114, 112, 2, 212, 3, 4, 8 114, 112, 2, 212, 3, 4, 6, 10 x 165, 6, 8 12 x 165, 6, 8, 10 57 42, 45, 48 mm 76 42, 48, 57, 60 mm 89 57, 76 mm 108 42, 48, 57, 60, 73, 76, 89 mm 114 57, 76 mm 133 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 140 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 159 42, 48, 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 165 42, 48, 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 168 57, 76, 108, 140 mm 219 57, 76, 108, 133, 140, 159, 165 mm 114 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 4 12, 34, 1, 114, 112, 2, 212, 3 6 12, 34, 1, 114, 112, 2, 212, 3 8 12, 34, 1, 114, 112, 2, 212, 3, 4 45 33, 42 mm 57 21, 27, 33, 42, 48 mm 76 21, 27, 33, 42, 48, 60 mm 89 76 mm 108 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 114 76 mm 133 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 140 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 159 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 165 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 168 76 mm 219 76, 140 mm 114 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 4 12, 34, 1, 114, 112, 2, 212, 3 6 12, 34, 1, 114, 112, 2, 212, 3 8 12, 34, 1, 114, 112, 2, 212, 3, 4 45 33, 42 mm 57 21, 27, 33, 42, 48 mm 76 21, 27, 33, 42, 48, 60 mm 89 76 mm 108 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 114 76 mm 133 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 140 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 159 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 165 21, 27, 33, 42, 48, 60, 73, 76, 89, 114 mm 219 76, 140 mm 114, 112, 2, 212, 3, 4, 6, 8 212 45, 57, 76, 108, 133, 140, 159, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 45, 57, 76, 108, 133, 140, 159, 165 mm 112 114 2 114, 112 212 114, 112, 2 3 114, 112, 2, 212 4 114, 112, 2, 212, 3 6 114, 112, 2, 212, 3, 4 8 114, 112, 2, 212, 3, 4, 6
300 (2070)
300 (2070)
300 (2070)
300 (2070)
300 (2070)
300 (2070)
FM Approvals
1-381
Product Designation
Fitting Description
Remarks
011
011L
012
012
012I
57 42, 48 mm 73 57 mm 76 42, 48, 57, 60 mm 89 57, 76 mm 108 42, 48, 57, 60, 73, 76, 89 mm 114 57, 76 mm 133 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 140 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 159 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 165 42, 48 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 168 57, 76, 108, 133, 140 mm 219 57, 76, 108, 133, 140, 159, 165 mm 112 114 2 114, 112 212 114, 112, 2 3 114, 112, 2, 2 1 2 4 114, 112, 2, 212, 3 6 114, 112, 2, 212, 3, 4 8 114, 112, 2, 12, 3, 4, 6 2 10 4, 5, 6, 8, 165 mm 12 4, 5, 6, 8, 10, 165 mm 57 42, 48 mm 73 57 mm 76 42, 48, 57, 60 mm 89 57, 76 mm 108 42, 48, 57, 60, 73, 76, 89 mm 114 57, 76 mm 133 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 140 42, 48, 57, 60, 73, 76, 89, 108, 114 mm 159 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 165 42, 48, 57, 60, 73, 76, 89, 108, 114, 133, 140 mm 168 57, 76, 108, 133, 140 mm 219 57, 76, 108, 133, 140, 159, 165 mm 114 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 4 12, 34, 1, 114, 112, 2, 212, 3 6 12, 34, 1, 114, 112, 2, 212, 3 8 12, 34, 1, 114, 112, 2, 212, 3 45 27, 33 mm 57 21, 27, 33, 42, 48 mm 76 21, 27, 33, 42, 48, 60 mm 89 76 mm 108 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 114 76 mm 133 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 140 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 159 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 165 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 168 76 mm 219 76 mm 114 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 4 12, 34, 1, 114, 112, 2, 212, 3 6 12, 34, 1, 114, 112, 2, 212, 3 8 12, 34, 1, 114, 112, 2, 212, 3
300 (2070)
300 (2070)
300 (2070)
300 (2070)
300 (2070)
300 (2070)
FM Approvals
1-382
Product Designation
Fitting Description
Remarks
012I
013
Eccentric Reducer
013
Eccentric Reducer
Grooved End Flange Grooved End Flange Grooved Weldolet With bevel
45 27, 33, 42 mm 57 21, 27, 33, 42, 48 mm 76 21, 27, 33, 42, 48, 60 mm 89 76 mm 108 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 114 76 mm 133 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 140 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 159 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 165 21, 27, 33, 42, 48, 60, 73, 76, 89 mm 168 76 mm 219 76 mm 212 x 2 3 x 2 1 2 4 212, 3 6 x 3, 4 8x4, 6 76 x 2 89 x 76 mm 108 73, 76, 89 mm 114 76 mm 133 89, 108, 114 mm 140 89, 108, 114 mm 159 108, 114, 133, 140 mm 165 76, 89, 108, 114, 133, 140 mm 168 108, 133, 140 mm 219 108, 133, 140, 159, 165 mm 114, 112, 2, 212, 3, 4, 6, 8, 10, 12 45, 57, 76, 108, 133, 140, 159, 165 mm 212 4 1, 2 -212 114, 3 4 114, 5 8 114, 2 1 1 2, 212 112, 3 4 112, 5 8 112, 212 2, 3 2, 4 2, 5 2, 6 2, 8 2, 3 212, 4 212, 5 212, 6 212, 8 2 1 2, 3 76, 4 76, 5 76, 6 76, 8 76, 4 3, 5 3, 6 3, 8 3, 5 4, 6 4, 8 4,8 6, 8 165 mm 2 212 1, 212 4 1, 2 -212 114, 3 4 114, 5 8 114, 2 1 1 2, 212 112, 3 4 112, 5 8 112, 212 2, 3 2, 4 2, 5 2, 6 2, 8 2, 3 212, 4 212, 5 212, 6 212, 8 2 1 2, 3 76, 4 76, 5 76, 6 76, 8 76, 4 3, 5 3, 6 3, 8 3, 5 4, 6 4, 8 4,8 6, 8 165 mm
300 (2070)
300 (2070)
300 (2070)
025B
300 (2070)
FM Approvals
1-383
Product Designation
Fitting Description
Remarks
035A
035B
114 112 12, 2 212 12, 212 8 12, 114 -112 34, 2 212 34, 212 8 34, 114 112 1, 2 - 212 1, 3 4 1, 5 8 1, 112 - 2 114, 2 - 212 114, 3 - 4 1 1 4, 5 8 114, 2 1 1 2, 212 112, 3 4 112, 5 8 112, 8 1 1 2, 212 2, 3 2, 4 2, 5 2, 6 2, 8 2, 3 212, 4 212, 5 212, 6 212, 8 2 1 2, 3 76, 4 76, 5 76, 6 76, 8 76, 1 112 12, 2 212 12, 3 8 12, 1 -112 34, 2 34, 212 34, 3 5 34, 6 8 34, 114 112 1, 2 1, 212 1, 3 1, 4 5 1, 6 8 1, 2 1 1 4, 212 114, 3 114, 4 5 114, 6 8 114, 2 1 1 2, 212 112, 3 1 1 2, 4 1 1 2, 5 6 112, 8 1 1 2, 212 2, 3 2, 4 2, 5 2, 6 2, 8 2, 3 212, 4 212, 5 212, 6 212, 8 2 1 2, 3 76, 4 76, 5 76, 6 76, 8 76
300 (2070)
300 (2070)
a. Threads per Chinese National Standard GB-3289.13289.39-82 b. Threads per ANSI/ASME B1.20.1 for tapered pipe threads (NPT).
Shanghai Recomb Piping System Co Ltd, No. 270 Yixian Rd, Shanghai 200434, P. R. China
Standard grooved and threaded pipe fittings conforming to ASTM A-536 (Grade 65-45-12) ductile iron, ANSI B2.1 taper threads according to NPT.
Product Designation Pipe Actual Size mm Fitting Description Max Working Pressure, psi (kPa)
XGQT01
42, 48, 60, 73, 76, 89, 108, 114, 133, 140, 141.3, 159, 165, 168 and 219 273 and 375
90 Elbow
XGQT01
90 Elbow
XGQT02
42, 48, 60, 73, 76, 89, 108, 114, 133, 141.3, 140, 159, 165, 168 and 219 273 and 375
45 Elbow
XGQT02
45 Elbow
FM Approvals
1-384
Product Designation
Fitting Description
XGQT03
42, 48, 60, 73, 76, 89, 108, 114, 133, 141.3, 140, 159, 165, 168 and 219 273 and 325
Tee
XGQT03
Tee
XGQT04
60x42, 60x48, 73x60, 76xG2, 76x60, 89xG2, 89xG212, 89x60, 89x73, 8976, 10876, 10889, 114xG212, 114xG3, 114x60, 114x73, 11476, 11489, 13376, 13389, 133108, 133114, 14076, 14089, 140114, 141.3x73, 141.3x88.9, 141.3x114.3, 15976, 15989, 159108, 159114, 159133, 159140, 165xG212, 165xG3, 16560, 16576, 16589, 165114, 165140, 168x60, 168x73, 16876, 16889, 168108, 168114, 168133, 168140, 168x141.3, 219108, 219114, 219133, 219140, 219159, 219165 and 219168 273159, 273165, 273219, 325159, 325165, 325219 and 325273 60, 76, 89, 108, 114, 133, 140, 159, 165, 168 and 219 273 and 325 mm 42, 48, 60, 73, 76, 89, 108, 114, 133, 141.3, 140, 159, 165, 168 and 219 273 and 325
Reducing Tee
XGQT04
Reducing Tee
175 (1205) 300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070)
XGQT06
Cap
XGQT07
60xG12, 60xG34, 60xG1, 60xG114, 60xG112, 73xG1, 73xG114, 73xG112, 76xG12, 76xG34, 76xG1, 76xG114, 76xG112, 76xG2, 89xG12, 89xG34, 89xG1, 89xG114, 89xG112, 89xG2, 89xG212, 108xG1, 108xG114, 108xG112, 108xG2, 114xG12, 114xG34, 114xG1, 114xG114, 114xG112, 114xG2, 114xG212, 114xG3, 133xG1, 133xG114, 133xG1-12, 133xG2, 140xG1, 140xG114, 140xG112, 140xG2, 140xG212, 140xG3, 141.3xG1, 141.3xG114, 141.3xG112, 159xG1, 159xG114, 159xG112, 159xG2, 165xG1, 165xG114, 165xG112, 165xG2, 165xG212, 165xG3, 168xG1, 168xG114, 168xG112, 168xG2, 168xG212 168xG3, 219xG1, 219xG114, 219xG112, 219xG2, 219xG212, 219xG3 60x42, 60x48, 73x48.3, 73x60.3, 76x42, 76x48, 7660, 89x42, 89x48, 88.9x73, 8960, 8976, 10876, 10889, 114x42, 114x48, 114x60, 114.3x73, 11476, 11489, 13376, 13389, 133108, 133114, 140x60,14076, 14089, 140114, 141.3x60.3, 141.3x73, 141.3x88.9, 141.3x114.3, 15976, 15989, 159108, 159114, 159133, 159140, 165x60, 16576, 16589, 165114, 165140, 168x60, 16876, 16889, 168108, 168114, 168133, 168140, 168.3x73, 168.3x141.3, 21976, 21989, 219108, 219114, 219133, 219140, 219159, 219165, 219168, 219.1x73 and 219.1x141.3 273108, 273114, 273133, 273140, 273159, 273165, 273168, 273219, 325159, 325165, 325168, 325219 and 325273 89x60P, 89x76P, 114x76P, 114x89P, 165x76P, 165x89P, 165x114P, 219x114P and 219x165P 273x219P
XGQT07
300 (1205)
XGQT07
175 (1205)
XGQT07 XGQT07
300 (2070) 175 (1205) 300 (2070) 175 (1205) 300 (2070)
XGQT08
60, 73, 76, 89, 108, 114, 133 140, 141.3, 159, 165, 168 and 219 273 and 325
Flange
XGQT08
Flange
XGQT08
ANSI 150 Flange American Standard (2, 212, 3, 4, 5, 6 and 8 in.) ANSI 150 Flange American Standard (10 and 12 in.)
XGQT08
175 (1205)
FM Approvals
1-385
Product Designation
Fitting Description
XGQT10
42, 48, 60, 73, 76, 89, 114, 140, 165, 168 and 219 273 and 325
22.5 Elbow
XGQT10
22.5 Elbow
XGQT18
114x89
Hydro-Run Elbow
Shanxi Jinbaote Machinery Industry Co Ltd, International Foundry Park, Eco. Development Area, Jincheng, Shanxi, China 048000
Product Designation Fitting Description Nominal Pipe Size, mm Rated Working Pressure, psi (kPa)
Rigid Coupling Flexible Coupling 90 Elbow 45 Elbow 22 Elbow 11.5 Elbow Tee Grooved Reducing Tee
60,76,89,108,114, 133,140, 159, 165, 219 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 89, 114, 140, 165 114, 140, 165 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 7660, 8960, 8976, 11460, 11476, 11489, 14060, 14076, 14089, 140114, 16560, 16576, 16589, 165114, 165140, 21989, 219114, 219140, 219165, 273165, 273219, 325219, 325273 7660, 8960, 8976, 11460, 11476, 11489, 14060, 14076, 14089, 16560, 16576, 16589 6033.5, 6042, 7633.5, 7642, 7648, 8933.5, 8942, 8948, 8960, 10833.5, 10842, 10848, 10860, 10876, 11433.5, 11442, 11448, 11460, 11476, 11489, 13333.5, 13342, 13348, 13360, 13376, 13389, 14033.5, 14042, 14048, 14060, 14076, 14089, 15933.5, 15942, 15948, 15960, 15976, 15989, 159114, 16533.5, 16542, 16548, 16560, 16576, 16589, 165114, 21942, 21948, 21960, 21976, 21989, 219114 11460, 11476, 11489, 14060, 14076, 14089, 15976, 15989, 159108, 159114, 16560, 16576, 16589, 165114, 21960, 21976, 21989, 219114 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 60,76,89,108,114,133, 140, 159, 165, 219 60,76,89,108,114,133, 140, 159, 165, 219, 273, 325 60,76,89,108,114,133, 140, 159, 165, 219 140114, 165114, 165140, 219114, 219165 11460, 11476, 11489, 14060, 14076, 14089, 16560, 16576, 16589 7633.5, 7642, 7648, 7660, 8933.5, 8942, 8948, 8960, 8976, 10833.5, 10842, 10848, 10860, 10876, 10889, 11433.5, 11442, 11448, 11460, 11476, 11489, 14033.5, 14042, 14048, 14060, 14076, 14089, 15933.5, 15942, 15948, 15960, 15976, 15989, 159114, 16533.5, 16542, 16548, 16560, 16576, 16589, 165114
230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600)
GCPQT04s
GCPT3s
GCQT3
230 (1600)
Flange Adaptor Grooved Split Flange Cap Cross Reducing Cross, Grooved Reducing Cross Threaded
230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600)
GCPQT07s
Reducer, Threaded
FM Approvals
1-386
Product Designation
Fitting Description
GCPQT07
Reducer, Grooved
7660, 8960, 8976, 10860, 10889, 11460, 11476, 11489, 14060, 14076, 14089, 140114, 15960, 15976, 15989, 159108, 159114, 16560, 16576, 16589, 165114, 165140, 219114, 219140, 219165, 273165, 273219, 325219, 325273
230 (1600)
Shield Fire, Safety and Security Ltd, 28th Floor Regus Suite, One Canada Square, Canary Wharf, London E14 5DY, United Kingdom
Product Designation Fitting Description Nominal Pipe size, mm Max Working Pressure, psi (kPa)
Model SDG100 Model SDG200 Model SDG200 Model SDG12 Model SDG12 Model SDG53
90 Elbow, Grooved Ends 45 Elbow, Grooved Ends 45 Elbow, Grooved Ends Equal Tee, Grooved Ends Equal Tee, Grooved Ends Reducing Tee, Grooved Ends
114,
114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2112, 31, 112, 2, 212, 41, 2, 212, 3, 52, 3, 4, 62, 212, 3, 4, 5, 82, 3, 4, 5, 6 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 61, 2, 212, 3, 4, 5, 12, 3, 4, 5, 6 82 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 12, 3, 4, 5, 6 82 234, 1, 114, 112, 2121, 114, 112, 2, 334, 1, 112, 2, 212, 41, 112, 2, 212, 3, 53, 4, 62, 212, 3, 4, 5, 12, 3, 4, 5, 6 82 114, 112, 2, 212, 3, 4, 5, 6, 8, 10, 12 76.1, 165 mm 2, 212, 3, 4, 5, 6, 8 76.1, 165mm
12, 34, 12, 34, 12, 34, 12, 34,
500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450)
Equal Cross, Grooved Ends Equal Cross, Grooved Ends Concentric Reducer, Grooved Ends
Model SDG37
500 (3450)
Model SDG39
500 (3450)
Model SDG14 Model SDG14 Model SDG16 Model SDG16 Model SDT14 Model SDT22 Model SDT100 Model SDT200 Model SDT57
Grooved End Cap Grooved End Cap FlangeGroove Adapter FlangeGroove Adapter D.I. Cap, Threaded D.I. Straight Coupling, Threaded D.I. 90 Elbow, Threaded D.I. 45 Elbow, Threaded D.I. Bushings, Threaded
1, 114, 112, 2, 212 1, 114, 112, 2, 212 1, 114, 112, 2, 212 1, 114, 112, 2, 212
Model SDT30
Model SDT101
112, 34 11434 21 112, 34 11434 21 3412 112, 34 11412, 34, 1 11234, 1, 114 234, 1, 114, 112 212112, 2
500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450)
FM Approvals
1-387
Product Designation
Fitting Description
Model SDT53
343412, 1 341234, 12
500 (3450)
Model SDT51 Model SDT55 Model SDT12 Model SDT59 Model SDT13 Model SDC100 Model SDC200 Model SDC30 Model SDC101
D.I. Reducing Cross, Threaded D.I. Square Head Pipe Plug D.I. Equal Tee, Threaded D.I. Union, Threaded D.I. Cross, Threaded C.I. 90 Elbow, Threaded C.I. 45 Elbow, Threaded C.I. Concentric Reducer, Threaded C.I. 90 Reducing Elbow, Threaded
1112, 34, 114, 112 13434, 1 1121 1411412, 34, 1, 112, 2 1 14112, 34, 1, 114, 112 1 11434114 11412114 11211212, 34, 1, 1, 114, 2 11211412, 34, 1, 114, 112 112112, 34, 1, 114, 112 11234114, 112 11212114, 112 12, 34, 1, 114, 112, 212 22 211212, 34, 1, 114, 112, 2 21142 212 21221234, 1, 114, 112, 2, 3 1141, 1121, 21
12, 34, 12, 34,
1,
114,
112,
1,
114,
112,
2, 212
Model SDC53
Model SDC12
112, 34 21 112, 34, 1412, 34, 1, 1 11212, 34, 1, 114, 12, 34, 1, 114, 112, 2 21234, 1, 114, 112, 2 11212, 34, 1, 13412, 34, 1, 1112, 34, 114, 11141, 1411412, 34, 1, 112, 2, 1 14112, 34, 1, 114, 112,, 1 11434114, 11412114, 11211212, 34, 1, 1, 114, 2, 11211412, 34, 1, 114, 112, 112112, 34, 1, 114, 112, 2, 11234114, 112, 11212114, 112, 2212, 34, 1, 114, 112, 211212, 34, 1, 114, 112, 2, 211412, 1, 114, 112, 2, 2134, 1, 114, 2, 22212, 212212, 34, 1, 114, 112, 2, 212, 2114212, 21212, 234212, 212122, 212 12, 34, 1, 114, 112, 2
500 (3450) 500 (3450) 500 (3450) 500 (3450) 500 (3450) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
300 (2070)
300 (2070)
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Nominal Pipe Size, in. Fitting Description Max Rated Pressure, psi (kPa)
1M1F 1F12F, 1F34F 1M1F 11412, 11434, 1141, 11212, 11234, 1121, 212, 234, 21, 21212, 21234, 2121
FM Approvals
1-388
Product Designation
Fitting Description
901
2, 212, 3, 4, 5, 6, 8
902
2, 212, 3, 4, 5, 6, 8
903
2, 212, 3, 4, 5, 6, 8
7110 7110 7110 7110 7110LR 7110DR 7111 7111 7111 7111 7112 7113 7120 7120 7120 7121
1 through 8 10 and 12 14, 16, 18, 24 20 2 through 8 2 through 6 114 through 8 10 and 12 14, 16, 18, 24 20 2 through 8 2 through 8 114, 112, 2, 212, 3, 4, 5, 6, 8 10, 12, 14 16 2112, 2122, 32, 3212, 42, 4212, 43, 63, 64 2 through 8 2, 212, 3, 4, 5, 6 2122, 32, 3212, 42, 4212, 43, 54, 62, 63, 64, 65, 84, 86, 104, 106, 108, 128, 1210, 146, 148, 1410, 1412 2122, 32, 3212, 42, 4212, 43, 54, 62, 63, 64, 65, 84, 86 114 through 12 10 and 12 14, 16, 18, 24 212, 3, 4, 5, 6 1, 114, 112, 2, 212 12, 34, 1, 114, 112, 2, 212
3412, 134, 112, 1141, 11434, 11412, 112114, 1121, 11234, 2112, 21, 234, 2122 12, 34, 1, 114, 112, 2, 212 1 2, 3 4,
Short Radius 90 Elbow Grooved Short Radius 45 Elbow Grooved Shurjoint Radius Tee Grooved Grooved 90 Elbow 1.5D 90 Elbows Drain Elbows Grooved 45 Elbow Grooved 45 Elbow Grooved 45 Elbow Grooved 45 Elbow Grooved 2212 Elbow Grooved 1114 Elbow Grooved Tee Grooved Tee Grooved Tee Grooved Reducing Tee Grooved 45 Laterals Grooved Cross Grooved Concentric Reducer
300 (2070)
300 (2070) 300 (2070) 500 (3447) 300 (2070) 175 (1205) 250 (1725) 300 (2070) 300 (2070) 500 (3447) 300 (2070) 175 (1205) 250 (1725) 300 (2070) 300 (2070) 500 (3447) 300 (2070) 175 (1205) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
7151
Eccentric Reducer
300 (2070)
7160 7160H 7160H 7170 Model 811 DI, 90 Elbows Model 813 DI, 45 Elbows Model 812 DI, Reducing Elbows
300 (2070) 300 (2070) 175 (1205) 175 (1205) 300 (2070) 300 (2070) 300 (2070)
Screwed Fittings
300 (2070)
FM Approvals
1-389
Product Designation
Fitting Description
Model 816 DI, Reducing Coupling Model 825 DI, Extension Pieces Model 817 DI, Crosses Model 818 DI, Straight Coupling Model 819 DI, Plug Model 820 DI, Cap Model 827 DI, Hex. Bushings
DI, Face Bushings Model 830 DI, Brass Seat Union Model 831 DI, Long Street Elbow Model 832 DI, Long Street Tee Model 899
343412, 1134, 1112, 1341, 13434, 13412, 1121, 1141141, 11411434, 1411412, 1141114, 1 11411, 114134, 114112, 11114, 112112114, 1121121, 11211234, 11211212, 112114112, 1121141, 11211434, 11211412, 1121112, 11211, 112134, 112112, 11112, 114114112, 1141112, 22112, 22114, 221, 2234, 2212, 21122, 2112112, 21121, 211234, 211212, 21142, 212, 1121122, 1121142, 212234, 22212 3412, 134, 112, 11412, 1121, 112134, 21, 2134, 2112 12112 L, 122 L, 34112 L, 342 L 1, 114, 112, 2, 1141, 1121, 21 12, 34, 1, 114, 112, 2, 212 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2, 212 134, 112, 1141, 11434, 11412, 112114, 1121, 11234, 11212, 2112, 2114, 21, 234, 212 1141, 112114, 1121, 2112, 2114 12, 34, 1, 114, 112, 2, 212 112 M, 11 M
Screwed Fittings
300 (2070)
Screwed Fittings Screwed Fittings Screwed Fittings Screwed Fittings Screwed Fittings Screwed Fittings Screwed Fittings
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
1121 M, 111 M 11212, 11234, 1121, 212, 234, 21, 21212, 21234, 2121
Screwed Fittings Screwed Fittings Screwed Fittings Screwed Fittings DI, End-All Fitting
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Standard threaded pipe fittings conforming to ASTM A-536 (Grade 65-45-12) ductile iron, ANSI B2.1 taper threads according to NPT. Unless otherwise noted in the listing, these fittings are ductile iron.
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
71
1 2 3 4
1 1 1 4 1 1 2 2 2 1 2 3 4 2 2 1 2 3 4 6 8 1 1 4 1 1 2 2 2 1 2 3
72C
1, 112, 2, 212, 3, 4, 5, 6, 8 1, 112, 2, 212, 3, 4, 5, 6, 8 114, 112, 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 2, 212, 3, 4, 5, 6, 8 212, 3, 4, 5, 6, 8 3, 4, 5, 6, 8 4, 5, 6, 8 5, 6, 8 212, 3, 4, 5, 6, 8 3, 4, 5, 6, 8 4, 5, 6, 8 5, 6, 8 8 10 12, 2, 212, 1 3, 4, 5, 8 2, 212, 3, 4, 6, 8 12, 3, 4, 5, 6, 8 2 3, 4, 5, 6, 8 4, 5, 6, 8
300 (2070)
300 (2070)
72R
300 (2070)
FM Approvals
1-390
Product Designation
Fitting Description
300 (2070)
Product Designation
Fitting Description
C10
2, 212, 3, 4, 6
Copper 90 Elbow
200 (1380) 200 (1380) 200 (1380) 200 (1380) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
C11
2, 212, 3, 4, 6
Copper 45 Elbow
C20
2, 212, 3, 4, 6
Copper Tee
C60
2, 212, 3, 4, 6
Copper Cap
55
112112, 22
Nipple Adaptor
7125
Bullhead Tee
7127
Standpipe Tee
7150F
1121, 2114,2112, 212114, 212112, 2122, 3114, 3112, 32, 4112, 42, 4212 1121, 2114,2112, 212114, 212112, 2122, 3114, 3112, 32, 4112, 42, 4212, 5112, 6112, 62, 6212, 64
7150M
Reducing Nipple
300 (2070)
7160T
21, 2114, 2121, 212114, 212112, 31, 3114, 3112, 32, 41, 4114, 4112, 42, 61, 6114, 6112, 62 2, 212, 3, 5, 6, 8
Transition Fitting
300 (2070)
7180
Adaptor
a, b, c, d
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 175 (1205)
SS-80
2, 212, 3, 4, 5, 6, 8
Adaptor
d, e
SS-10
90 Elbow
SS-11
45 Elbow
SS-20
Tee
SS-60
Cap
SS-21
3212, 4212
Reducing Tee
SS-21F
32, 42
SS-50
212212, 3212,4212
SS-50F
2122, 32, 42
610
1, 114, 2
d, f, g, h
FM Approvals
1-391
Product Designation
Fitting Description
Remarks
612
Speed 90 Elbow
d, f, g, h
620
114, 112
Speed Tee
d, f, g, h
622
111, 1141141, 221 1112, 1134, 11411412, 11411434, 2212, 2234 114112, 34, 1; 11211412, 34, 1; 211212, 34, 1 1, 114
d, f, g, h
626
d, f, g, h
175 (1205)
630
a. b. c. d. e. f. g. h. j.
a, b, c, d
175 (1205)
Provides a rigid transition between flanged components and a grooved system. Min schedule cut groove pipe to be joined: 8 inches or smaller Schedule 40. Min schedule rolled groove pipe to be joined: 8 inches or smaller Schedule 10. EPDM gasket. Stainless steel material. Schedule 10 and 40. Mega-Thread pipe. Rapid-Thread pipe Copper material.
SFM
EK
1, 114, 112, 2 (25, 32, 38, 50) 1, 114, 112, 2 (25, 32, 38, 50) 1, 114, 112, 2 (25, 32, 38, 50) 1114, 114112, 1122 (2532, 3238, 3850) 1, 114, 112, 2 (25, 32, 38, 50) 1114114, 1112112, 114112112, 122, 22114, 22112 (253232, 253838, 323838, 255050 505032, 505038) 1138, 1112, 11411438, 11411412, 11211238, 11211212, 11211234, 121121, 2212, 2234, 1 221 (252510, 252513, 323210, 323213, 383810, 383813, 383819, 383825, 505019, 505025) 1, 114, 112, 2 (25, 32, 38, 50)
Plain-End Coupling Plain-End 90 Elbow Plain-End 45 Elbow Plain-End Reducer Plain-End Tee Plain-End Reducer Tee
a a a a a a
232 (1600) 232 (1600) 232 (1600) 232 (1600) 232 (1600) 232 (1600)
232 (1600)
Plain-End Cap
232 (1600)
a. For use with DIN 2440, 2448 and 2458 (ISO 4200) steel pipe.
37T
Tee
FM Approvals
1-392
Product Designation
Fitting Description
37RT
Reducing Tee
37RC
Concentric Reducer
1 by 34 by 34, 34, 1; 1 by 34 by 34, 34, 1; 1 by 1 by 34, 34, 114; 1 by 14 by 1; 114 by 114 by 34, 34, 1, 112, 2; 114 by 1 by 34, 34, 1, 114, 112; 114 by 34 by 114; 114 by 34 by 114; 12 by 112 by 34, 34, 1, 114, 2; 1 112 by 114 by 34, 34, 1, 114, 112; 112 by 1 by 34, 34, 1, 114, 112, 2; 112 by 34 by 114, 112; 112 by 12 by 114, 112; 2 by 2 by 34, 34, 1, 114, 112; 2 by 112 by 34, 34, 1, 114, 112, 2; 2 by 114 by 34, 1, 114, 112, 2; 2 by 1 by 34, 1, 114, 2; 2 by 2 by 234; 212 by 2 by 34, 34, 1, 114, 112, 2, 212; 2 by 114 by 212; 2 by 1 by 212; 2 by 34 by 212; 12 by 12 by 2, 212 2 1 by 34, 34; 2 by 1
Threaded Ductile Iron Fittings. Rated working pressure is 500 psi (3445 kPa) 35E 35F 35RE 90 Elbow 45 Elbow 90 Red. Elbow to 212 to 212 34 by 12; 1 by 34, 34; 114 by 34, 34, 1; 112 by 34, 1, 114; 2 by 34, 1, 114, 112; 212 by 112, 2; 12 to 212 12 to 212 12 to 212 34 by 34 by 12, 1; 34 by 12 by 34, 12; 1 by 1 by 12, 34, 114, 112; 1 by 34 by 34, 1; 1 by 12 by 1; 114 by 114 by 34, 34, 1, 112, 2; 114 by 1 by 34, 34, 1, 114, 112; 114 by 34 by 114; 114 by 12 by 114; 12 by 112 by 34, 34, 1, 114, 2; 1 12 by 114 by 34, 34, 1, 114, 112; 1 112 by 1 by 34, 34, 1, 114, 112; 112 by 34 by 114, 112; 112 by 12 by 114, 112; 2 by 2 by 34, 34, 1, 114, 112, 212; 2 by 112 by 34, 34, 1, 114, 112, 2; 2 by 114 by 2; 2 by 1 by 2; 212 by 212 by 34, 1, 114, 112, 2, 3; 1 to 2 1 by 34, 34; 14 by 34; 1 2 by 1 1 by 34, 34; 114 by 1; 112 by 1, 114; 2 by 1, 114, 112; 1 thru 2 34 thru 212 34 to 2 114 by 1, 112 by 1, 2 by 1 12, 34, 1, 114, 112, 2, 212 112, 34; 11412, 34, 1; 11212, 34, 1, 114; 212, 34, 1, 114, 112; 21234, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 12, 34, 1, 114, 112, 2 1 by 12 by 1 thru 212 by 212 by 2 112, 34 21
12 12
35X 35RC
35HB
Bushing
Union End Cap Sq. Head Pipe Plug Reducing Cross 90 Elbows Reduc. Elbows
FM Approvals
1-393
Product Designation
Fitting Description
Coop-lets
1 1 4 1 1 2 2 2 1 2 3 4 1 1 4 1 1 2 2 2 1 2 3 4 6 33E 90 Elbows
12
Coop-lets
1, 114, 112; 2, 212; 3 1, 114, 112, 2; 212; 3 114; 112; 2; 212; 3 112; 2; 212; 3; 4, 6 2; 212; 3; 4; 6 212; 3; 4; 6 3; 4; 6; 8 4; 6; 8 6; 8 112; 2; 212; 3; 4; 6; 8 2; 212; 3; 4; 6; 8 212, 3; 4; 6; 8 3; 4; 6; 8 4; 6; 8 6; 8 8 500 (3445) 300 (2070) 500 (2070) 500 (2070) 300 (2070) 500 (3445) 500 (3445) 500 (3445)
thru 4 5, 6
33RE
Reducing Elbows, 90
1 2
14 thru 43 thru 4 5, 6
33F
Elbows, 45
12
33L
Lateral Y Branch
12
thru 4
33CP
Coupling
12
thru 4
33RC
Reducing Coupling
3 8 3 8, 1 2 1 38, 12, 34 114 12, 34, 1 112 12, 34, 1, 114 2 12, 34, 1, 114, 112 212 112, 2 3 112, 2, 212 4 2, 3
34
1 2
33HB
Bushing
1 4, 3 8 3 8, 1 2 1 1 2, 3 4 114 12, 34, 1 112 38, 12, 34, 1, 114 2 38, 12, 34, 1, 114, 112 212 12, 34, 1, 114, 112, 2 3 12, 34, 1, 114, 112, 2, 212 312 212, 3 4 34, 114, 112, 3, 312 5 2, 3, 4 6 2, 212, 3, 312, 4, 5
12
1 2 3 4
500 (3445)
33P
thru 4
500 (3445) 500 (3445) 300 (2070) 500 (3445) 300 (2070)
33BP
4 5, 6
33C
Cap
12
thru 4 5, 6
Rated Working Pressure of the Coop-let Series Weldolets is 300 psi (2070 kPa) when used with Schedule 10, Schedule 40, or non-threadable lightwall pipe. When used with Schedule 5 pipe, the rated working pressure is 175 psi (1205 kPa).
FM Approvals
1-394
710, 1010, 4010 710D, 1010D, 4010D 711, 1011, 4011 712, 1012, 4012 713, 1013, 4013 714, 1014, 4014 715, 1015, 4015 716, 1016, 4016 710F, 1010F, 4010F 711F, 1011F, 4011F 710GP, 1010GP, 4010GP 711GP, 1011GP, 4011GP 712GP, 1012GP, 4012GP 713GP, 1013GP, 4013GP 714GP, 1014GP, 4014GP 715GP, 1015GP, 4015GP 716GP, 1016GP, 4016GP 710P, 1010P, 4010P 711P, 1011P, 4011P 712P, 1012P, 4012P 713P, 1013P, 4013P 714P, 1014P, 4014P 715P, 1015P, 4015P 716P, 1016P, 4016P 710LR, 1010LR, 4010LR 7103D, 10103D, 40103D 7105D, 10105D, 40105D 7106D, 10106D, 40106D 712LR, 1012LR, 4012LR 7123D, 10123D, 40123D 7125D, 10125D, 40125D 7126D, 10126D, 40126D 7105R, 10105R, 40105R 710GF, 1010GF, 4010GF 712GF, 1012GF, 4012GF 4010TG 4012TG 719, 1019, 4019
90 Elbow, Grooved 90 Drain Elbow, Grooved 60 Elbow, Grooved 45 Elbow, Grooved 30 Elbow, Grooved 22.5 Elbow, Grooved 11.25 Elbow, Grooved 9.5 Elbow, Grooved 90 Elbow, Flanged 45 Elbow, Flanged 90 Elbow, Grooved/Plain 60 Elbow, Grooved/Plain 45 Elbow, Grooved/Plain 30 Elbow, Grooved/Plain 22.5 Elbow, Grooved/Plain 11.25 Elbow, Grooved/Plain 9.5 Elbow, Grooved/Plain 90 Elbow, Plain 60 Elbow, Plain 45 Elbow, Plain 30 Elbow, Plain 22.5 Elbow, Plain 11.25 Elbow, Plain 9.5 Elbow, Plain 90 Elbow, Grooved, Long Radius (1.5 D) 90 Elbow, Grooved, Long Radius (3 D) 90 Elbow, Grooved, Long Radius (5 D) 90 Elbow, Grooved, Long Radius (6 D) 45 Elbow, Grooved, Long Radius (1.5 D) 45 Elbow, Grooved, Long Radius (3 D) 45 Elbow, Grooved, Long Radius (5 D) 45 Elbow, Grooved, Long Radius (6 D) 90 Elbow, Short Radius 90 Elbow, GroovedFlange 45 Elbow, GroovedFlange 90 Elbow, GroovedMPT 45 Elbow, GroovedMPT Roof Elbow, Grooved
114 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 2 1 1 2 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 1 1 4 114 1 1 4 1 1 4 1 1 4
through through through through through through through through through through through through through through through through through through through through through through through through through
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
114 through 12 2 through 12 2 through 12 114 through 12 2 through 12 2 through 12 2 through 12 2 through 6 114 through 12 14 through 12 1 1 through 6 1 through 6 114 through 8 (any angle from 1 to 60) 114 through 12 14 through 12 1 114 through 8 2 through 6 112 through 12 112 through 12 114 through 12 114 through 12 114 through 12 114 through 12 114 through 12 112 through 12 112 through 12 112 through 12 112 through 12 114 through 12 114 through 12 114 through 12 1 1 4 1 1 4 1 1 4 1 1 4 through through through through 12 12 12 12
730, 1030, 4030 730P, 1030P, 4030P 730M, 1030M, 4030M 730SR, 1030SR, 4030SR 730F, 1030F, 4030F 731F, 1031F, 4031F 731P, 1031P, 4031P 731PM, 1031PM, 4031PM 731, 1031, 4031 731PG, 1031PG, 4031PG 731M, 1031M, 4031M 1030FP, 4030FP 1031FP, 4031FP 1031FM, 4031FM 1031FG, 4031FG 732, 1032, 4032 7331, 1033, 4033 735, 1035, 4035 734F, 1034F, 4034F 740, 1040, 4040 740P, 1040P, 4040P 740F, 1040F, 4040F
Tee, Grooved Tee, Plain Tee, GroovedGroovedMPT Tee, Short Radius Tee, Flanged Tee, Reducing Flanged Tee, Plain Tee, Reducing PlainMPT Tee, Reducing Grooved Tee, Reducing PlainGrooved Tee, Reducing PlainMPT Tee, FlangedPlain Tee, Reducing FlangedPlain Tee, Reducing PlainMPT Tee, Reducing FlangedGrooved Tee, Reducing Run, Grooved Tee, Bullhead, Grooved Tee, Reducing Run and Outlet, Grooved Tee, FPT Outlet Cross, Grooved Cross, Plain Cross, Flanged
FM Approvals
1-395
Product Designation
Fitting Description
760, 1060, 4060 4061 4062 1063, 4063 4064 4065 4066 1018G, 4018G 1018GF, 4018GF 1018F, 4018F 1018FF, 4018FF 10RMGG, 40RMGG 40RMGT 40RMTT 1017F, 4017F 1017G, 4017G 1017GF, 4017GF 1017FF, 4017FF S10 720, 1020, 4020 720P, 1020P, 4020P 724, 1024, 4024 725C, 1025C, 4025C 725E, 1025E, 4025E 721C, 1021C, 4021C 721E, 1021E, 4021E 722C, 1022C, 4022C 722E, 1022E, 4022E 723C, 1023C, 4023C 723E, 1023E, 4023E
Adaptor Nipple, Grooved Adaptor Nipple, GroovedMPT Adaptor Nipple, GroovedBevel Adaptor Nipple, GroovedFlanged Adaptor Nipple, FlangedMPT Adaptor Nipple, FlangedBevel Adaptor Nipple, MPTBevel Riser Tee, Grooved Outlet Riser Tee, Grooved and Plain Outlet Riser Tee, FlangedGrooved Riser Tee, FlangedGroovedPlain Riser Manifold, GroovedGrooved Riser Manifold, GroovedMPT Riser Manifold, Threaded Short Riser Tee, Flanged Short Riser Tee, Grooved Short Riser Tee Short Riser Tee Drip Drum, MPT End Cap, Grooved End Cap, Plain End Cap, Grid, Grooved End Cap, Drain, Concentric End Cap, Drain, Eccentric Reducer, Grooved, Concentric Reducer, Grooved, Eccentric Reducer, GroovedMPT, Concentric Reducer, GroovedMPT, Eccentric Reducer, Plain, Concentric Reducer, Plain, Eccentric
1 through 12 1 through 12 1 through 12 112 through 12 112 through 12 112 through 12 1 through 12 212 through 12 Run 212 through 12 Run 212 through 12 Run 212 through 12 Run 112 through 6 112 through 6 112 through 6 through 12 through 12 through 12 through 12 1 114 through 12 114 through 12 114 through 12 112 through 12 112 through 12 114 through 12 114 through 12 114 through 12 114 through 12 114 through 12 114 through 12 3 3 3 3
Branch connections for attachment to pipe by welding. For use with Schedule 10S or heavier pipe unless otherwise noted. Requires precutting of hole in pipe. Rated working pressure 114 through 5 in., 300 psi (2070 kPa). Rated working pressure 6 and 8 in. 250 psi (1725 kPa).
Product Designation Fitting Description Nominal Outlet Size, in. Nominal Pipe Size, in.
1 through 10 1 through 10
Tyco Fire Products, 1550 Valley Center Pkwy, Suite 135, Bethlehem PA 18017
Fig. No. Description Sizes (in.)
811 812 813 814 815 817 818 816 827 819 820
90 Elbows Reduc. Elbows 45 Elbows Tees Reducing Tees Cross Straight Coupling Conc. Reducer Hex Bushing Sq. Head Plug End Cap
thru 212 38 thru 212 2 12 thru 212 12 thru 212 34 by 34 by 12 thru 2 by 2 by 112 12 thru 212 12 thru 212 12 38 thru 212 2 12 38 thru 212 2 12 thru 212 12 thru 212
12
1 2
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
45 Elbow
90 Elbow
1-12
FM Approvals
1-396
Product Designation
Fitting Description
76, 165 mm Grinnell Figure 210DE Grinnell Figure 219 90 Drain Elbow Tee 212-8 1-12 76, 165 mm Grinnell Figure 221 Reducing Tees 2 2 112 3 3 1, 2, 76 mm 76 76 2 4 4 2, 3, 76 mm 165 165 3, 4 6 6 2, 3, 4, 76 mm 1121 21, 114, 112 2122 76 mm112, 2 32, 212, 76 mm 42, 212, 76 mm, 3 139 mm3, 4 54 62, 76 mm, 4, 139 mm, 5 1 114-12 Grinnell Figure 501 Grinnell Figure 501S Grinnell Figure 510 Grinnell Figure 510DE Grinnell Figure 510S Grinnell Figure 519 Grinnell Figure 519S 45 Elbow 45 Elbow Short Radius 90 Elbow 90 Drain Elbow 90 Elbow Short Radius Tee Tee, Short Radius 114-8 1-12 76.1, 139.7, 165.1 mm 114-8 212-8 2-8 76, 139, 165 mm 114-8 2-8 76, 139, 165 mm
300 (2070) 300 (2070) 500 (3445) 300 (2070) 500 (3445)
Concentric Reducer
500 (3445)
End Cap
500 (3445) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Product Designation
Fitting Description
1, FNPT 1, BSP
Standard threaded pipe fittings conforming to ASTM A-536 (Grade 65-45-12) ductile iron, ANSI B2.1 taper threads according to NPT. Rated working pressure 300 psi (2070 kPa).
Product Designation Fitting Description Nominal Pipe Size, in.
811 812
815
Bullhead Tee
112 through 212 12 through 114 3412; 112,34; 11412,34, 1; 11234, 1, 114; 234, 1, 112; 2122 12 through 212 12 through 212 343412; 1121; 13412,34, 1; 114112,34, 1; 1141114; 11211412,34, 1; 112112,34, 1, 112, 212; 2114, 112; 211212,34, 1, 112, 2; 22, 114, 112; 212234; 11114, 112; 1141112; 114114112; 1121122;
FM Approvals
1-397
Product Designation
Fitting Description
22212 112, 1 1121 111 3412, 112, 134 1, 114, 112, 2 11411411; 11211211; 2211 12 through 212 12 through 2 12 through 212
Max Rated Pressure, psi (kPa)
227 227
Cross Cross
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
527 527
Cross Cross
825
1212; 3434
827
830
600 (4135)
Segmentally welded fittings, made from Schedule 40 pipe. Rated working pressure 300 psi. Roll grooved ends unless otherwise specified.
Product Designation Fitting Description Nominal Pipe Size, in.
Grinnell Figure 312 Grinnell Figure 313 Grinnell Figure 319 Grinnell Figure 320 Grinnell Figure 321 Grinnell Figure 323 Grinnell Figure 326 Grinnell Figure 350 Grinnell Figure 372 Grinnell Figure 351 Grinnell Figure 315 Grinnell Figure 301 Grinnell Figure 302 Grinnell Figure 303 Grinnell Figure 327 Grinnell Figure 341
22.5 Elbow 11.25 Elbow Equal Tee Tee, Groove by Thread Reducing Tee Reducing Tee, Groove by Thread 90 Drain Elbow Concentric Reducer Concentric Reducer, Groove by Thread Eccentric Reducer 90 Elbow, Groove by Thread Adapter Nipples, Groove by Thread Adapter Nipples Adapter Nipples, Groove by Bevel Equal Cross Adapter, Flange by Groove
114 to 12 114 to 12 114 to 12 112 to 6 114 to 12 114 to 12 114 to 12 114 to 12 114 to 12 114 to 12 1 to 6 1 to 12 1 to 12 1 to 12 114 to 12 112 to 12
FM Approvals
1-398
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
300 (2070)
1-6 8-12
2-6
250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 250 (1725) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 300 (2070) 300 (2070) 250 (1725) 300 (2070) 250 (1725) 500 (3445) 300 (2070) 500 (3445) 500 (3445) 300 (2070) 500 (3445)
8-12 Fig. 219S, 219L Fig. 219TS Fig. 223TS Fig. 221S, 221L Fig. 221S, 221L Fig. 225S, 225L Fig. 224S, 224L Fig. 215S, 215L Tee Grooved Tee, Gr/Gr/Th Tee, Reducing Gr/Gr/Th Tee, Reducing, Grooved Tee, Reducing, Grooved Standpipe Tee, Grooved Bullhead Tee, Grooved Lateral, Reducing, Grooved 10, 12 112-6 212-5 Run
2-6 Run 8-12 Run 44212, 66212 558, 668 3-6 Run 8-12 Run
Lateral, Grooved
Fig. 216S
433 through 654 864 through 868 2-6 Run 8-12 Run
Fig. 250S
Fig. 251S
1121 through 6212 83 through 1210 1121 through 6212 83 through 1210 1121 through 63 2-6 8-12
Fig. 243S
2-6 8-12
201
45 Elbow
210
90 Elbow
FM Approvals
1-399
Product Designation
Fitting Description
210 219
250
Reducing Coupling
260
End Cap
112 by 1 2 by 1, 114, 112 212 by 2 76 mm by 112, 2 3 by 2, 212, 76 mm 4 by 2, 212, 76 mm, 3 139 mm by 3, 4 5 by 4 165 by 3, 4, 139 mm 6 by 2, 76, 4, 139, 5 114-10 12 76, 139, 165 mm
300 (2070) 500 (3445) 300 (2070) 500 (3445) 500 (3445)
45 Elbow 90 Elbow 90 Drain Elbow 90 Elbow Short Radius Tee Tee, Short Radius
114-8 114-8 212-8 2-8 76, 139, 165 mm 114-8 2-8 76, 139, 165 mm
500 (2070) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Note: Suffix -L stands for Schedule 10 raw material, Suffix -S stands for Schedule 40 raw material. Product Designation Nominal Outlet Size, in.
12, 34, 12, 34,
Fitting Description
ADACAP ADACAP
1, FNPT 1, BSP
Standard threaded pipe fittings conforming to ASTM A-536 (Grade 65-45-12) ductile iron, ANSI B2.1 taper threads according to NPT. Rated working pressure 300 psi (2070 kPa).
Product Designation Fitting Description Nominal Pipe Size, in.
811 812
815
Bullhead Tee
112 through 212 12 through 114 1238 through 2122 3412; 112, 34; 11412, 34, 1; 11234, 1, 114; 234, 1, 112; 2122 12 through 212 12 through 212 343412; 1121; 13412, 34, 1; 114112, 34, 1; 1141114; 11211412, 34, 1; 112112, 34, 1, 112, 212; 2114, 112; 211212, 34, 1, 112, 2; 22, 114, 112; 212234; 11114, 112; 1141112; 114114112; 1121122; 22212 3412, 112, 134 1238 through 2122 12 through 212 1, 114, 112, 2
FM Approvals
1-400
Product Designation
Fitting Description
817
Reducing Cross
Straight Couplings Sq. Head Plug Cap Hex Bushing 90 Street Elbow California Fitting
11411411; 11211211; 2211 12 through 212 12 through 212 12 through 212 1238 through 2122 112, 1 1121 111
Product Designation
Fitting Description
825
1212; 3434
827
112, 34; 11412, 34, 1; 11212, 34, 1, 114; 212, 34, 1, 114, 112
1 2
830
through 2 NPT
600 (4135)
Segmentally welded fittings, made from Schedule 40 pipe. Rated working pressure 300 psi. Roll grooved ends unless otherwise specified.
Product Designation Fitting Description Nominal Pipe Size, in.
201 312 313 219 320 321 323 326 350 372 351 315 301 302 303 327 341
45 Elbow 22.5 Elbow 11.25 Elbow Equal Tee Tee, Groove by Thread Reducing Tee Reducing Tee, Groove by Thread 90 Drain Elbow Concentric Reducer Concentric Reducer, Groove by Thread Eccentric Reducer 90 Elbow, Groove by Thread Adapter Nipples, Groove by Thread Adapter Nipples Adapter Nipples, Groove by Bevel Equal Cross Adapter, Flange by Groove
114 to 12 114 to 12 114 to 12 114 to 12 112 to 6 114 to 12 114 to 12 114 to 12 114 to 12 114 to 12 114 to 12 1 to 6 1 to 12 1 to 12 1 to 12 114 to 12 112 to 12
Notes
Uni-let Weldolet
a, b, c, d, e, f, g, h, i, j, k a, b, c, d, e, f, g, h, i, j, k a, b, c, d, e, f, g, h, i, j, k
3 4
Branch Connection for attachment to pipe by welding. Requires pre-cutting of hole on pipe and removal of coupon. Rated Working Pressure 300 psi (2070 kPa).
For use with steel sprinkler pipe as follows: a. Min schedule cut groove pipe to be joined: 6 in. or smaller Schedule 40; 8 in. or larger Schedule 30. Standard schedule 10 rolled groove pipe: 6 in. or smaller 8 in. or 10 in. 0.188 in. (5 mm) wall. b. For use with Allied Dyna-thread, Dyna-flow, Super-flo, and BLT pipe. c. For use with Tex-Tube Tex-flow Pipe. d. For use with Wheatland Tube SL pipe, WLS, Mega-flow, MLT, and Mega-thread. e. For use with Bull Moose Tube EDDY-lite, EDDYthread 40, and EDDY-flow. f. For use with Northwest Pipe EZ-flow pipe. g. For use with WIFP Fire Flow and Rapid-thread pipe. h. For use with Youngstown Pipe Fire-flo and EZ-Thread pipe.
FM Approvals
1-401
i. For use with IDOD Gal-7 and Gal-flo pipe. j. For use with Welded Tube-Berkeley LLC Steady-flow and Steady-thread pipe. k. For use with Yieh Phui Enterprise SPS Flow pipe. Product Designation Fitting Description Nominal Threaded Outlet Size, in.
1 2
Notes
a a a
Uni-let Weldolet
3 4
Branch Connection for attachment to pipe by welding. Requires pre-cutting of hole on pipe and removal of coupon. Rated Working Pressure 300 psi (2070 kPa).
For use with steel sprinkler pipe as follows: a. Min schedule cut groove pipe to be joined: 6 in. or smaller BS1387 Heavy; 8 in. Schedule 30. Standard BS1387 Medium rolled groove pipe: 6 in. or smaller 8 in. 0.188 in. (5 mm) wall Schedule 10 pipe.
114; 112 through 212; 212 through 8 114 through 212; 212 through 8 114; 112 through 2; 212 through 8 112; 2 through 212; 3 through 4; 5 through 8 2, 212; 3 through 4; 5 through 8 212, 3; 4 through 8 3 through 4; 5 through 8
34
1 1 4
1 1 2
2 2 1 2
Rated working pressure of the Cericeo Series Tee-lets is 300 psi (2070 kPa). FM Approved for use with Schedule 10 and 40 Run pipes, Steady-flow, 112 thru 4 in., Super-flo, 1 thru 4 in., Dyna-flow, 1 thru 4 in., EDDY-flow, 112 thru 4 in., Gal-flo and Gal-7, 114 thru 2 in., EZ-flow, 3 thru 6 in., Tex-flow, 212 thru 6 in., Fire-flow, 114 thru 3 in., Mega-flow 114 thru 4 in., and Fire-Flo, 112 thru 4 in.
10
90 Elbow
through 12 76, 108, 133, 139.7, 159, 165 mm 216, 267, 318 mm
10D
90 Elbow
11
45 Elbow
216, 267, 318 mm 12 13 18 19 2212 Elbow 1114 Elbow 90 Adapter Elbow 45 Adapter Elbow 114, 112, 4 114, 112, 2, 212, 3, 4, 6, 8
3 4 3 4
through 6 through 6
FM Approvals
1-402
Product Designation
Fitting Description
20
Tee
500 (3445)
21
Bullhead Tee
58; 68 234, 1, 2121; 31, 2; 41, 112, 2, 212, 3; 5 by 212 165 mm114 mm 4212;
34 through 4; 234, 1, 2121; 31, 2; 41, 112, 2, 212, 3; 5212 62, 3
25
Reducing Tee
27
6212
29
30 35
Lateral Cross
2, 3, 4, 8 2, 3, 4 76, 165 mm 1121, 114; 234, 1, 114, 112; 212114, 112, 2; 31, 112, 2, 212; 3123;41, 2, 212, 3, 312; 54; 61, 2, 212, 3, 4, 5; 83, 4, 5, 6; 104, 6, 8; 126, 8, 10 165 by 76, 114 mm 1121; 234, 1, 114, 112 2122; 31, 2, 212; 41, 2, 212, 3; 61, 2, 212, 3
34 through 12 76, 108, 133, 140, 159, 165 mm
50
52
60 66
212, 34, 1 NPT and BSP 21212, 34, 1 NPT and BSP 11412, 34, 1, 11212, 34, 1, 212, 34, 1, 21212, 34, 1 2, 3, 4 500 (3450)
67
80
Tee 45 Elbow
001
90 Elbow
006
End Cap
Vic-End
2 through 4, 76, 108 mm 5 through 8, 159,165 mm 2 through 4, 76, 108 mm 5 through 8, 139, 159, 165 mm 2 through 4, 76, 108 mm 5 through 8, 139, 159, 165 mm 114 through 4, 73, 76 mm 5 through 8, 165 mm 2 and 212
350 (2415) 300 (2070) 350 (2415) 300 (2070) 350 (2415) 300 (2070) 350 (2415) 300 (2070) 350 (2415)
90 Steel Elbow
300 (2070)
FM Approvals
1-403
Product Designation
Fitting Description
Pressure (kPa)
Style 410 SS
Style 411
45 Steel Elbow
Style 411 SS
Style 420
Steel Tee
Style 420 SS
Style 425
Style 425 SS
3, 4, 5, 6, 8 108, 139.7, 159, 165, 216 mm 2, 212, 3, 4, 5, 6, 76, 108, 139.7, 159, 165, 216 mm 3, 4, 5, 6, 8 108, 139.7, 159, 165, 216 mm 2, 212, 3, 4, 5, 6 76, 108, 139.7, 159, 165, 216 mm 3, 4, 5, 6, 8, 108, 139.7, 159, 165, 216 mm 2112, 114 2122, 112 3212, 76 mm 43, 212 54, 3 64, 3 86, 4 76 mm2, 112 1394, 3 1654, 3 216165, 4 376, 212 43, 212 1394, 3 1654, 3 64, 3 216165, 4 86, 4
250 (1725) 300 (2070) 250 (1725) 300 (2070) 250 (2070) 300 (2070)
250 (1725)
Style 500 Series Press-Fit Couplngs. To be installed with Victaulic pressing tools, Type EPU or PFT 505, only. FM Approved for use with Allied Tube & Conduit Dyna-Light, Bull Moose Ultra-EDDY or Wheatland WST Schedule 5 pipe in wet pipe systems in sizes 1 through 2 in., and for use with valve trim and accessories in 34 in. size; FM Approved for use with IDOD Systems Gal-5 pipe in 114-2 in. sizes.
Product Designation Fitting Description Nominal Pipe Size, in.
Standard Coupling (PP) Slip Coupling (PP) Short Radius Elbow (PF)
509 510
Short Radius Elbow (PP) 90 Elbow Reducing (PF) 90 Elbow Reducing (PP) 90 Elbow (PP) 45 Elbow (PP) Straight Tee (PPP) Tee Reducing Branch (PPP)
510
520
520
Tee Reducing Branch and Run (PPF) Tee Reducing Branch and Run (PPP) End of Line Fitting (PCF)
520
520
520
535 550
through 2 through 2 112, 34, 1; 11412, 34; 11212, 34; 234 1, 114, 112, 2 112, 34; 11412, 34; 11212, 34 1141; 1121; 112114 34 through 2 34 through 2 34 through 2 134; 11434, 1; 11234, 1; 234, 1 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1 114112, 34; 11211412, 34; 211212, 34 11411 1121141; 21121 1134; 11411412, 34; 11211234, 1; 2212, 34, 1 1134; 11411434; 1211234, 1; 1 2234, 1, 112 34, 1, 114, 112, 2 134; 11434, 1; 1121, 114; 2114, 112
3 4
3 4
FM Approvals
1-404
Product Designation
Fitting Description
1, 114, 112, 2 3412, 34; 112, 34, 1 3412, 34, 1; 134, 1; 114114; 112112; 22
Style 96 Fast Installation Technique (FIT) Reducing Tee. NPT internal threaded branch connection. Run connects two plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe) or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
96 FIT Reducing Tee 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1; 112 through 21
Style 929 Mechanical Tee with Fast Installation Technique (FIT) Branch Outlet. Clamps over hole in run pipe. Also for use as crosses in any possible combination. With grade E (green stripe) or L (solid red) gasket material. Also FM Approved with Allied Dyna-Flow Lightwall pipes. Not FM Approved for Schedule 5 pipe.
929 Mechanical T Branch Outlet Cross 2114*, 112*; 212114*, 112*; 3114, 112, 2; 4114, 112, 2
*These sizes also available with NPT internal threaded outlet. Schedule 10S or heavier.
Style 960 Fast Installation Technique (FIT) Coupling. Connects two plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
960 FIT Coupling 1, 114, 112, 2
Style 961 Fast Installation Technique (FIT) Elbow. Connects two plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
961 FIT Elbow 1, 114, 112, 2
Style 963 Fast Installation Technique (FIT) Straight Tee. Connects three plain-end Lightwall, Thinwall, 10S or heavier pipes for branch connection. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
963 FIT Tee 111; 114114114; 112112112; 222
Style 966 Fast Installation Technique (FIT) Reducing Elbow. NPT internal threaded drop nipple or sprigs. Connects plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
966 FIT Reducing Elbow 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1
Style 969 Fast Installation Technique (FIT) Reducing Tee. NPT internal threaded branch connection. With Grade E (green stripe) or L (solid red) gasket material. Connects plain end Lightwall, Thinwall, 10S or heavier pipe. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
969 FIT Reducing Run and Outlet Tee 114112, 34, 1; 11211412, 34, 1; 211212, 34, 1
All FM Approved for use on Allied Tube & Conduits Super-Flo non-threadable Lightwall pipe at 175 psi (1205 kPa). For use with Central Sprinkler TL threadable Thinwall pipe, 1-2 in. sizes, plus IDOD Gal-7 and Gal-flo and Wheatland Mega-Flow 114-2 in. sizes.
Fast Installation Technique (FIT) pipe fittings. Connects two plain end Lightwall, Thinwall, 10S or heavier pipes as listed below. Not FM Approved for Schedule 5 pipe.
Product Designation Fitting Description Nominal Pipe Size, in. Remarks Max Working Pressure, psi (kPa)
960
FIT Coupling
1, 114, 112, 2 1 1 2, 2
a, b, c, e, f, h d
961 963
1,
114,
112,
a, b, c, f, h a, b, c, f, h
FM Approvals
1-405
Product Designation
Fitting Description
Remarks
966
969
112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1 114112, 34, 1; 1211412, 34, 1; 1 211212, 34, 1
a, b, c, f, g, h
175 (1205)
a, b, c, f, h
175 (1205)
a. b. c. d. e. f. g. h.
With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for use with Schedule 5 pipe. For use on Allied Tube & Conduits Super-Flo non-threadable Lightwall steel sprinkler pipe For use with Youngstown Tube Fire-Flo non-threadable Lightwall steel sprinkler pipe. For use with Youngstown Tube EZ-Thread threadable Thinwall steel sprinkler pipe. For use with Central Sprinkler TL threadable Thinwall steel sprinkler pipe. NPT internal threaded drop nipple or sprigs. For use with IDOD Systems GAL-flo and GAL-7 pipe, 114-2 in. sizes.
10
90 Elbow
10D 11
90 Elbow 45 Elbow 2212 Elbow 1114 Elbow 90 Adapter Elbow 45 Adapter Elbow Tee
12 13 18 19 20
21 25
27 29
30 35 50
60 80
through 12 3, 414, 514, 614 and 6.5* 212 through 6 with drain outlets 34 through 12 3, 414, 514, 512, 614 and 6.5 4 2, 3, 4, 6, 8 34 through 6 34 through 6 34 through 12 3, 414, 514, 512, 614 and 6.5 58; 68 234, 1; 31, 2; 41, 2, 212, 3 4212; 6212 34 through 4; 234, 1; 31, 2; 41, 2, 212, 3; 62, 3 2, 3, 4, 8 2, 3, 4 1121; 234, 1, 114, 112; 2122; 31, 2, 212; 3123; 41, 2, 212, 3, 312; 54; 61, 2, 3, 4, 5; 83, 4, 5, 6; 104, 6, 8; 126, 8, 10 34 through 12 3, 414, 514, 512, 614, 612* 2, 3, 4 5 1 2,
3 4
*Metric equivalents: 76.1, 108, 133, 139.7, 159 and 165 mm, 175 psi (1205 kPa) rated working pressure. For steel pipe, couplings or fittings having metric sized outside dia. (ref. DIN 2448 & 2458).
Firelock Pipe Fittings. Cast ductile iron grooved-end fittings. 175 psi (1205 kPa).
Product Designation Fitting Description Nominal Pipe Size, in.
FM Approvals
1-406
Product Designation
Fitting Description
Style 500 Series Press-Fit Couplngs. To be installed with Victaulic pressing tools, Type EPU or PFT 505, only. FM Approved for use with Allied Tube & Conduit Dyna-Light, Bull Moose Ultra-EDDY or Wheatland WST Schedule 5 pipe in wet pipe systems in sizes 1 through 2 in., and for use with valve trim and accessories in 34 in. size.
505 506 509 Standard Coupling (PP) Slip Coupling (PP) Short Radius Elbow (PF) through 2 through 2 112, 34, 1; 11412, 34; 11212, 34; 234 1, 114, 112, 2 112, 34; 11412, 34; 11212, 34 1141; 1121; 112114 34 through 2 34 through 2 34 through 2 134; 11434, 1; 11234, 1; 234, 1 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1 114112, 34; 11211412, 34; 211212, 34 11411 1121141; 21121 234 34, 1, 114, 112, 2 134; 11434, 1; 1121, 114; 2114, 112 3412, 34; 112, 34, 1 3412, 34, 1; 134, 1; 114114; 112112; 22
3 4 3 4
509 510
Short Radius Elbow (PP) 90 Elbow Reducing (PF) 90 Elbow Reducing (PP) 90 Elbow (PP) 45 Elbow (PP) Straight Tee (PPP) Tee Reducing Branch (PPP)
510
520
520
Tee Reducing Branch and Run (PPF) Tee Reducing Branch and Run (PPP) End of Line Fitting Equal Cross Reducer-Insert (IP)
520
580 580
Style 96 Fast Installation Technique (FIT) Reducing Tee. NPT internal threaded branch connection. Run connects three plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe) or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
96 FIT Reducing Tee 112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1; 112 through 21
Style 929 Mechanical Tee with Fast Installation Technique (FIT) Branch Outlet. Clamps over hole in run pipe. Also for use as crosses in any possible combination. With grade E (green stripe) or L (solid red) gasket material. Also FM Approved with Allied Dyna-Flow Lightwall pipes. Not FM Approved for Schedule 5 pipe.
929 Mechanical T Branch Outlet Cross 2114*, 112*; 212114*, 112*; 3114, 112, 2; 4114, 112, 2
*These sizes also available with NPT internal threaded outlet. Schedule 10S or heavier.
Style 960 Fast Installation Technique (FIT) Coupling. Connects two plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
960 FIT Coupling 1, 114, 112, 2
Style 961 Fast Installation Technique (FIT) Elbow. Connects two plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
961 FIT Elbow 1, 114, 112, 2
Style 963 Fast Installation Technique (FIT) Straight Tee. Connects three plain-end Lightwall, Thinwall, 10S or heavier pipes for branch connection. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
FM Approvals
1-407
Product Designation
Fitting Description
963
FIT Tee
Style 966 Fast Installation Technique (FIT) Reducing Elbow. NPT internal threaded drop nipple or sprigs. Connects plain end Lightwall, Thinwall, 10S or heavier pipes. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
966 FIT Reducing Elbow 112, 34, 1; 11412, 34, 1; 11212, 34, 1
Style 969 Fast Installation Technique (FIT) Reducing Tee. NPT internal threaded branch connection. With Grade E (green stripe) or L (solid red) gasket material. Connects plain end Lightwall, Thinwall, 10S or heavier pipe. With Grade E (green stripe), or L (solid red) gasket material. Not FM Approved for Schedule 5 pipe.
969 FIT Reducing Run and Outlet Tee 114112, 34, 1; 11211412, 34, 1; 211212, 34, 1
All FM Approved for use on Allied Tube & Conduits Super-Flo non-threadable Lightwall pipe at 175 psi (1205 kPa). For use with Central Sprinkler TL threadable Thinwall pipe, 1-2 in. sizes.
4, 6 8
Fig. 6010
90 Elbow
1-6 76, 108, 133, 139, 159, 165 mm 8-12 1-6 76, 108, 133, 139, 159, 165 mm 8-12 1-6 76, 108, 133, 139, 159, 165 mm 8-12 21 through 86 2114 through 1210 1 through 6 76, 108, 133, 139, 159, 165 mm 8-12
6011
45 Elbow
6020
Equal Tees
500 (3445) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 300 (2070) 500 (3445) 300 (2070) 300 (2070) 300 (2070) 500 (3445) 300 (2070)
90 Elbow
114-8 76, 139, 165 mm 114-8 76, 139, 165 mm 114-8 76, 139, 165 mm
Fig. 2011
45 Elbow
Fig. 2020
Equal Tee
Virotec Rohrtechnik GmbH & Co KG, Meininger Weg 8, D-36132 Eiterfield, Germany
Rotating U, Z and L shaped pipe unions for use as sprinkler drops below suspended ceilings.
Product Designation End Connections Remarks
Flexarm Triflexarm
Flexarm FL 1 Flexarm FL 2
a. b. c. d. Adjustable in the horizontal plane only. Adjustable in the horizontal and vertical planes. Attached above the sprinkler pipe run. Attached below the sprinkler pipe run.
1 in. NPS. Male 1 in. NPS. Female 1 in. NPS. Male 34 in. NPS. Female 1 in. NPS. Male 12 in. NPS. Female 1 in. NPS. Male 38 in. NPS. Female 1 in. NPS Male 1 in. NPS Female 1 in. NPS Male 1 in. NPS Female
a b b b a, c a, d
FM Approvals
1-408
5000
5010
Reducing Run Tee with Threaded Branch Coupling 90 Elbow 90 Elbow Quick Connect X Thread Slip Tee
112, 34, 1; 11412, 34, 1; 11212, 34, 1; 212, 34, 1 114112, 34, 1; 11211412, 34, 1; 211212, 34, 1 1, 114, 112, 2 1, 114, 112, 2 112, 34, 1 111; 114114114; 12112112; 1 222 221; 22114; 22112 1121122
5060
Reducing Tee
5065
Bullhead Tee
Threaded Fittings.
175 psi, 1205 (kPa) (unless otherwise specified)
Fig. No.
Description
1 and 2 3 and 4 5 5 9
Cast Iron Pipe Plug C.I. Pipe Plug Mall. Iron Pipe Plug C.I. Pipe Plug C.I. Hex Bushing
14 19 20 21 22
C.I. Flanged Union Blind Flange, C.I. Companion Flange, C.I. C.I. 90 Elbow C.I. Reducing Elbow
23 24 25
29
C.I. Reducer
30 30A 30A 47 47
C.I. Cap C.I. Cross C.I. Reducing Cross M.I. 90 Elbow M.I. Reducing Elbow
48 49 50 51 52 52
M.I. 45 Elbow M.I. Cap M.I. 90 Street El M.I. 45 Street El M.I. Tee M.I. Reducing Tee
53 61 64 71 73 91 92
M.I. Coupling M.I. Cross M.I. Street Tee C.I. Red. Comp. Flg. Heavy Flanged Union Brass to Iron Union Brass to Iron Union
FM Approvals
1-409
Flanged Fittings
Long Radius 90 El 90 Elbow Reducing El 45 Elbow 2212 Elbow 1114 Elbow Concentric Reducer
Eccentric Reducer
2-12 3 by 2 through 12 by 10 2-12 12 by 3 through 12 by 10 4-12 2-12 6 by 4 8 by 6 2-12 2-12 2-12 3 by 2 through 12 by 10 6 by 4 through 12 by 10
Weifang 100tong Co Ltd, No. 1919 Jinchang South Road, Weicheng District, Weifang, Shandong, PR China 261052
Product Designation Fitting Description Nominal Pipe Size, mm Rated Working Pressure, psi (kPa)
60, 76, 89, 108, 114, 133, 140, 159, 165, 168, 219, 273, 325 60, 76, 89, 108, 114, 133, 140, 159, 165, 168, 219, 273, 325 60, 76, 89, 108, 114, 133, 140, 159, 165, 168, 219, 273, 325 8976, 10876, 10889, 11476, 11489, 14076, 14089, 140114, 15976, 15989, 159108, 159114, 159140, 16576, 16589, 165108, 165114, 165133, 165140 60, 76, 89, 108, 114, 133, 140, 159, 165, 219 60, 76, 89, 108, 114, 133, 140, 159, 165, 219, 273, 325 60, 76, 89, 108, 114, 140, 159, 165, 219, 273, 325 601, 60114, 60112, 761, 761 14, 76112, 891, 89114, 891 12, 892, 1081, 108114, 1081 12, 1082, 1141, 114114, 1141 12, 1142, 1331, 133114, 1331 12, 1332, 1401, 140114, 1401 12, 1402, 1591, 159114, 1591 12, 1592, 1651, 165114, 1651 12, 1652, 2191, 219114, 2191 12, 2192 7660, 8960, 8976, 10876, 10889, 11476, 11489, 13376, 13389, 133108, 133114, 14076, 14089,140114, 15976, 15989, 159108, 159114, 159133,16576, 16589, 165108, 165114, 165140,21976, 21989, 219108, 219114,219140, 219159, 219165, 273108, 273114, 273159, 273165, 273219, 325114, 325140, 325165,325219, 325273
230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600)
GCPQT07
Reducer, Grooved
230 (1600)
Remarks
1 1 1 4
a a
FM Approvals
1-410
Outlet Connection
Remarks
Threaded NPT Threaded NPT Threaded NPT Threaded NPT Threaded NPT Threaded NPT Threaded NPT Threaded NPT Threaded NPT Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End Grooved End 1, 1, 1,
1 1 1 1 1 1 1 1 1
76.1mm
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
a a a a a a a b b a a a a a a a a a a a a b b b b
a. Approved when manufactured using DIN 2440 pipe. b. Approved when manufactured using DIN 2448 pipe: 168.3mm (OD) 5.0mm (Wall), 219.1mm (OD) 6.3mm (Wall)
STEEL PIPE
This pipe is FM Approved for use in automatic sprinkler systems. Unless otherwise noted in individual listings, pressure rating is 175 psi (1205 kPa) and use is limited to wet-pipe systems. In addition to certain specific FM Approvals requirements, Approval is based upon conformance to American Society for Testing and Materials (ASTM) Standards. ASTM A-53 and A-135 are used for Schedule 40 pipe (and Schedule 30 in larger sizes) and ASTM A-135 for Schedule 10 (0.188 in. (5 mm) wall pipe in larger sizes). Pipe meeting ASTM A-795 is also approvable. Generally, joining by threading or cut-grooving is limited to pipe of the standard-weight Schedules, 30 or 40. Schedule 10 pipe is usually joined by roll-grooving. Lightwall pipe is non-threadable, is close to Schedule 5 in size, but is non-standard in wall thickness. Thinwall pipe is threadable, is close to Schedule 10 in size, but is also non-standard in wall thickness. The life expectancy of steel piping products varies widely depending on characteristics such as the water conditions and pipe material, as well as wall thickness. Such factors should be considered when selecting piping products. Approval of any piping product is not confirmation of equivalent field longevity to any pipe schedule or material identified in this introductory section. All FM Approved pipe is suitable for joining by welding or FM Approved plain end fittings where so listed. When welding pipe products, close adherence to recognized welding procedures and the use of welders certified under these procedures shall be followed. Pipe of other schedules or unusual joint design may be FM Approved if shown to be of comparable performance to the traditional products. Approval of individual pipe fittings and couplings may limit them to use with specific schedules of pipe or at specific pressure ratings. Use caution to ensure that a given pipe fitting or coupling is FM Approved for use on a given schedule of pipe and that the rated working pressures are compatible. In all cases, the installation instructions of both the pipe manufacturer and the pipe fitting or coupling manufacturer should be observed.
FM Approvals
1-411
Pressure ratings of completed sprinkler systems are determined by the lowest pressure rated component in the system.
Schedule 80 Normal connections are threaded, welded, rolled or cut groove, or plain end
Manufacturer Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa) Remarks
Borusan Mannesmann Boru Hisar Mahallesi Gemsaz Mekvii 16601 Gemlik Bursa Turkey
Remarks:
Schedule 80
300 (2070)
a, b, c
a. FM Approved for use with FM Approved pipe couplings on rolled or cut grooves. b. FM Approved for use with FM Approved pipe fittings when threaded. c. FM Approved for use in welded systems when supplied with standard bevel on ends.
Schedule 40 Normal connections are threaded, welded, rolled or cut groove, or plain end
Manufacturer Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
175 (1205)
Remarks
Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Borusan Mannesmann Boru Hisar Mahallesi Gemsaz Mekvii 16601 Gemlik Bursa Turkey Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Corcoran Piping Systems 500 Ternes Drive Monroe MI 48162 Corcoran Piping Products Systems 500 Ternes Drive Monroe, MI 48162 Hickman Pipe and Tube Corp 944 Indian Peak Rd #100 Rolling Hills Estates CA 90274-3591 Hickman Pipe and Tube Corp 944 Indian Peak Rd #100 Rolling Hills Estates CA 90274-3591 Mittal Canada 5870 Rue Saint Patrick Montreal H4E 1B3 Canada Mittal Canada 5870 Rue Saint Patrick Montreal H4E 1B3 Canada
Schedule 40
1, 114, 112, 2
a, b, c, d, g
Schedule 40
300 (2070)
a, b, c, d
Schedule 40
300 (2070)
a, b, c
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, g
Schedule 40
300 (2070)
a, b, c
Schedule 40
300 (2070)
a, b, c, d
Schedule 40
175 (1205)
d, g
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, g
Schedule 40
1, 114, 112, 2
300 (2070)
a, b, c
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, d, g
Schedule 40
300 (2070)
a, b, c, d
FM Approvals
1-412
Manufacturer
Product Description
Remarks
SAFT Trading Co Ltd No. 20 Tian Hua Yuan 2 Li 2 Qu King Building, Room 316 BDA Beijing, 100176 Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tex-Tube Co 1503 North Post Oak Rd Houston TX 77255-5710 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Western International Forest Products Box 3070 Portland OR 97208 Western International Forest Products Box 3070 Portland OR 97208 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505
Remarks: a. b. c. d. g.
Schedule 40
4, 6, 8
300 (2070)
a, b, c, d
Schedule 40
300 (2070)
a, b, c, d
Schedule 40
3, 4, 6, 8
300 (2070)
a, b, c
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, g
Schedule 40
300 (2070)
a, b, c
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, g
Schedule 40
300 (2070)
a, b, c
Schedule 40
34,
1, 114, 112, 2
175 (1205)
a, b, c, d, g
34,
Schedule 40
300 (2070)
a, b, c, d
Schedule 40
1, 114, 112, 2
175 (1205)
a, b, c, g
Schedule 40
1, 114, 112, 2
300 (2070)
a, b, c
FM Approved for use with FM Approved pipe couplings on rolled or cut grooves. FM Approved for use with FM Approved pipe fittings when threaded. FM Approved for use in welded systems when supplied with standard bevel on ends. When hot dip galvanized by factory, the sprinkler pipe is FM Approved for dry pipe systems. FM Approved for use with plain-end fittings.
Remarks
Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154
Schedule 10
114, 112, 2
a, c, d, g
Schedule 10
300 (2070)
a, c, d
FM Approvals
1-413
Manufacturer
Product Description
Remarks
Borusan Mannesmann Boru Hisar Mahallesi Gemsaz Mekvii 16601 Gemlik Bursa Turkey Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Corcoran Piping Products Systems 500 Ternes Drive Monroe, MI 48162 Corcoran Piping Products Systems 500 Ternes Drive Monroe, MI 48162 Hickman Pipe and Tube Corp 944 Indian Peak Rd #100 Rolling Hills Estates CA 90274-3591 Hickman Pipe and Tube Corp 944 Indian Peak Rd #100 Rolling Hills Estates CA 90274-3591 Mittal Canada 5870 Rue Saint Patrick Montreal H4E 1B3 Canada Mittal Canada 5870 Rue Saint Patrick Montreal H4E 1B3 Canada Northwest Pipe Co 8154 Industrial Park Lane Box 610 Atchison KS 66002 SAFT Trading Co Ltd No. 20 Tian Hua Yuan 2 Li 2 Qu King Building, Room 316 BDA Beijing, 100176 Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tex-Tube Co 1503 North Post Oak Rd Houston TX 77255-5710 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Western International Forest Products Box 3070 Portland OR 97208
Schedule 10
300 (2070)
a, c
Schedule 10
1, 114, 112, 2
175 (1205)
a, c, g
Schedule 10
300 (2070)
a, c
Schedule 10
300 (2070)
a, c, d
Schedule 10
175 (1205)
d, g
Schedule 10
114, 112, 2
175 (1205)
a, c, g
Schedule 10
300 (2070)
a, c
Schedule 10
114, 112, 2
175 (1205)
a, c, d, g
Schedule 10
300 (2070)
a, c, d
Schedule 10
3, 4, 6, 8
300 (2070)
a, c
Schedule 10
4, 6, 8
300 (2070)
a, c, d
Schedule 10
300 (2070)
a, c, d
Schedule 10
212, 3, 4, 6, 8
300 (2070)
a, c
Schedule 10
1, 114, 112, 2
175 (1205)
a, c, g
Schedule 10
300 (2070)
a, c
Schedule 10
114, 112, 2
175 (1205)
a, c, g
FM Approvals
1-414
Manufacturer
Product Description
Remarks
Western International Forest Products Box 3070 Portland OR 97208 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505
Remarks: a. c. d. g.
Schedule 10
300 (2070)
a, c
Schedule 10
1, 114, 112, 2
175 (1205)
a, c, d, g
Schedule 10
300 (2070)
a, c, d
Schedule 10
114, 112, 2
175 (1205)
a, c, g
Schedule 10
300 (2070)
a, c
FM Approved for use with FM Approved pipe couplings on rolled grooves. FM Approved for use in welded systems when supplied with standard bevel on ends. When hot dip galvanized by factory, the sprinkler pipe is FM Approved for dry pipe systems. FM Approved for use with plain-end fittings.
Thinwall Pipe Non-schedule Normal connections are threaded, welded, rolled groove or plain end
Manufacturer Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
175 (1205)
Remarks
Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154
XL and XL-II
1, 114, 112, 2
a, c, d, e, g
XL and XL-II
300 (2070)
a, c, d, e
Super-XL
1, 114, 112, 2
175 (1205)
a, c, d, e, g
Super-XL
300 (2070)
a, c, d, e
Super-40
1, 114, 112, 2
175 (1205)
a, c, d, e, g
Super-40
300 (2070)
a, c, d, e
BLT
1, 114, 112, 2
175 (1205)
a, c, d, e, g
BLT
1, 114, 112, 2
300 (2070)
a, c, d, e
Dyna-Thread
1, 114, 112, 2
175 (1205)
a, c, d, e, g
Dyna-Thread
1, 114, 112, 2
300 (2070)
a, c, d, e
FM Approvals
1-415
Manufacturer
Product Description
Remarks
Borusan Mannesmann Boru Hisar Mahallesi Gemsaz Mekvii 16601 Gemlik Bursa Turkey Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Western International Forest Products Box 3070 Portland OR 97208 Western International Forest Products Box 3070 Portland OR 97208 Western International Forest Products Box 3070 Portland OR 97208 Western International Forest Products Box 3070 Portland OR 97208 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161
Schedule 30
300 (2070)
a, e, f, c
EDDY-lite
1, 114, 112, 2
175 (1205)
a, c, e, g
EDDY-lite
1, 114, 112, 2
300 (2070)
a, c, e
EDDY-Thread
1, 114, 112, 2
175 (1205)
a, c, e, g
EDDY-Thread
1, 114, 112, 2
300 (2070)
a, c, e
Schedule 30
300 (2070)
a, c, e, f
Steady Thread
1, 114, 112, 2
300 (2070)
a, c, e
Rapid-Thread
1, 114, 112, 2
175 (1205)
a, c, e, g
Rapid-Thread
1, 114, 112, 2
300 (2070)
a, c, e
Rapid-Thread Light
1, 114, 112, 2
175 (1205)
a, c, e, g
Rapid-Thread Light
1, 114, 112, 2
300 (2070)
a, c, e
WLS
1, 114, 112, 2
175 (1205)
a, c, d, e, g
WLS
1, 114, 112, 2
300 (2070)
a, c, d, e
Mega-Thread
1, 114, 112, 2
175 (1205)
a, c, e, g
Mega-Thread
1, 114, 112, 2
300 (2070)
a, c, e
MLT
1, 114, 112, 2
175 (1205)
a, c, e, g
MLT
1, 114, 112, 2
300 (2070)
a, c, e
FM Approvals
1-416
Manufacturer
Product Description
Remarks
Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505
Remarks:
GL
1, 114, 112, 2
a, c, e, g
GL
1, 114, 112, 2
300 (2070)
a, c, e
EZ-Thread
1, 114, 112, 2
175 (1205)
a, c, e, g
EZ-Thread
1, 114, 112, 2
300 (2070)
a, c, e
a. FM Approved for use with FM Approved pipe couplings on rolled grooves. c. FM Approved for use in welded systems when supplied with standard bevel on ends. d. When hot dip galvanized by factory, the sprinkler pipe is FM Approved for dry pipe systems. e. Any FM Approved pipe coupling or fitting suitable for use with Schedule 10 pipe may be used with this product at the lower rated pressure of the pipe or the fitting. f. This product is not FM Approved for threaded connections. g. FM Approved for use with plain-end fittings.
Lightwall Pipe Non-threadable Non-schedule Normal connections welded, rolled groove or plain end
Manufacturer Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
175 (1205)
Remarks
Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Borusan Mannesmann Boru Hisar Mahallesi Gemsaz Mekvii 16601 Gemlik Bursa Turkey Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940 IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940
Dyna-Flow
1, 114, 112, 2
a, c, d, g, h
Dyna-Flow
300 (2070)
a, c, d, h
Dyna-Flow
175 (1205)
c, d, h
Super-Flo
1, 114, 112, 2
175 (1205)
a, c, d, g, h
Super-Flo
300 (2070)
a, c, d, h
Easy-Flow
300 (2070)
a, c, h
EDDY-Flow
114, 112, 2
175 (1205)
g, h
EDDY-Flow
300 (2070)
a, c, h
Gal-7
114, 112, 2
175 (1205)
a, c, d, g, h
Gal-7
114, 112, 2
300 (2070)
a, c, d, h
FM Approvals
1-417
Manufacturer
Product Description
Remarks
IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940 IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940 Northwest Pipe Co 8154 Industrial Park Lane Box 610 Atchison KS 66002 Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Tex-Tube Co 1503 North Post Oak Rd Houston TX 77255-5710 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Welded Tube Berkeley LLC 1100 North Steel Circle Huger SC 29450 Western International Forest Products Box 3070 Portland OR 97208 Western International Forest Products Box 3070 Portland OR 97208 Wheatland Tube Co 1 Council Ave Wheatland PA 16161 Wheatland Tube Co 1 Council Ave Wheatland PA 16161
Gal-flo
114, 112, 2
a, c, g, h
Gal-flo
114, 112, 2
300 (2070)
a, c, h
EZ-Flow
3, 4, 6
300 (2070)
a, c, h
TFQ Flow I
300 (2070)
a, c, d, h
TFQ Flow II
112, 2, 3, and 4
300 (2070)
a, c, d, h
TFQ Flow II
76.1mm, 165.1mm
300 (2070)
a, c, d, h
112, 2, 3, 4, and 6
300 (2070)
a, c, d, h
76.1mm, 165.1mm
300 (2070)
a, c, d, h
Tex-Flow
212, 3, 4, 6
300 (2070)
a, c, h
Steady Flow
114, 112, 2
175 (1205)
a, c, g, h
Steady Flow
300 (2070)
a, c, h
Fire-Flow
114, 112, 2
175 (1205)
a, c, g, h
Fire-Flow
300 (2070)
a, c, h
Mega-Flow
114, 112, 2
175 (1205)
a, c, g, h
Mega-Flow
300 (2070)
a, c, h
FM Approvals
1-418
Manufacturer
Product Description
Remarks
Yieh Phui Enterprise Co Ltd 369 Yu Liao Road Chiao Tou Hsiang Kaohsiung Hsien 825 Taiwan Yieh Phui Enterprise Co Ltd 369 Yu Liao Road Chiao Tou Hsiang Kaohsiung Hsien 825 Taiwan Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505 Youngstown Tube Co 401 Andrews Ave Youngstown OH 44505
Remarks: a. c. d. g. h.
SPS Flow
300 (2070)
a, c, h
SPS Flow
114, 112, 2 2 1 2
175 (1205)
g, h
Fire-Flo
112, 2
175 (1205)
a, c, g, h
Fire-Flo
112, 2, 212, 3, 4
300 (2070)
a, c, h
FM Approved for use with FM Approved pipe couplings on rolled grooves. FM Approved for use in welded systems when supplied with standard bevel on ends. When hot dip galvanized by factory, the sprinkler pipe is FM Approved for dry pipe systems. FM Approved for use with plain-end fittings. FM Approved for use when the listings of the couplings or fittings make specific mention of their suitability with this sprinkler pipe.
Schedule 5 Non-threadable Lightwall Pipe Normal connections welded, Press-Fit, limited Approval of rolled groove
Manufacturer Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
175 (1205)
Remarks
Allied Tube & Conduit 11350 Norcom Rd Philadelphia PA 19154 Bull Moose Tube Co 1819 Clarkson Rd Chesterfield MO 63017 Geberit Mapress GmbH Kronprizstr. 40 D-40746 Langenfeld Germany Geberit Mapress GmbH Kronprizstr. 40 D-40746 Langenfeld Germany IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940 IDOD Systems L.C. 13415 East Route 17 Grant Park IL 60940 Tai Feng Qiao Metal Products Road #3 Jie Dong Economy Development Testing Zone Jieyang, Guangdong Province Peoples Republic of China Wheatland Tube Co 1 Council Ave Wheatland PA 16161
Remarks: a. c. d. h. i.
Dyna-Light
34,
1, 114, 112, 2
a, c, d, h, i, l
Ultra-EDDY
1, 114, 112, 2
175 (1205)
a, c, h, i, j, l
175 (1205)
a, h, i, j, l
175 (1205)
a, h, i, j, k, l
Gal-5
114, 112, 2
175 (1205)
a, c, d, h, i, l
All-Gal
114, 112, 2
175 (1205)
a, c, h, i, l
Schedule 5
114, 112, 2
300 (2070)
a, c, d
WST
34,
1, 114, 112, 2
175 (1205)
a, c, h, i, j, l
FM Approved for use with FM Approved pipe couplings on rolled grooves. FM Approved for use in welded systems when supplied with standard bevel on ends. When hot dip galvanized by factory, the sprinkler pipe is FM Approved for dry pipe systems. FM Approved for use when the listings of the couplings or fittings make specific mention of their suitability with this sprinkler pipe. FM Approved for use with a 12 ft maximum hanger spacing.
FM Approvals
1-419
j. 34 in. (20 mm) nominal size limited to use in valve trim. k. FM Approved for use in dry sprinkler systems. l. FM Approved for use when joined by FM Approved Press-Fit Couplings.
through 2
3 4
12 1 12 1 34 (Internal Slip FNPT) 34 12; 1 12; 114 12; (Slip FNPT) through 2 through 2 34 through 2 34 through 2 34 through 2 34 through 2 1 1 3 4; 114 114 34, 1; 112 112 34, 1, 114; 2 2 34, 1, 114, 112 34 1; 1 114, 112; 14 112; 1 112 2 34 through 2 34 1, 114, 112, 2; 1 114, 112, 2; 114 112, 2; 112 2 34 12; 1 12; 114 12; (Slip FNPT) 34 12 1 12 (External Slip FNPT) 34 through 2
34 34
Socket (Slip Slip) 45 Elbow (Slip Slip) 90 Elbow (Slip Slip) Cap (Slip) Tee (Slip Slip Slip) Cross (4 Slips) Reducing Tee (Slip Slip Slip)
Flange, Slip
through 3
3 4
FM Approvals
1-420
Product Description
Coupling (Slip Slip) 45 Elbow (Slip Slip) 90 Elbow (Slip Slip) Cap (Slip) Tee (Slip Slip Slip) Cross (4 Slips) Reducing Tee (Slip Slip Slip)
Reducing Cross Sprinkler Head Adaptor 90 Elbow Transition Coupling (Slip Cut Groove) Sprinkler Head Adapter Tee Female Adapter Assembly, Str.
34
through 3* through 2* through 2* 34 through 3* 34 through 3* 34 through 2* 34 34 1; 1 34 1; 1 34 34; 1 1 3 4; 114 114 34, 1, 112; 112 112 34, 1, 114, 2; 114 1 34, 1, 114; 112 1 112; 112 114 34, 1 2 2 34, 1, 114, 112 1 1 1 2 3 4 3 4 1 2 34 1, 114, 112, 2; 1 114, 112, 2; 114 112, 2; 112 2 1 1 3 4 3 4 1 12
34 34
34
Durman Esquivel S.A., Camino La palma Estacion El Ahorcado Km 1.5, El Ahorcado, Pedro Escobedo, Qro. C.p. 76700 Mexico
BLAZEMASTER CPVC SDR 13.5 CPVC Pipe. Joined by solvent cement method using BM-5 or TFP-500 One Step CPVC cement. Pressure ratings 175 psi (1205 kPa) at 150F (66C). FM Approval limited to use with appropriate Approved BlazeMaster solvent cement type fittings. Approved for exposed use when all of the following criteria are met: Occupancy must be covered in Data Sheet 3-26, Fire Protection Water Demands for Nonstorage Sprinklered Properties, Table 2, Section L, Miscellaneous Non-manufacturing. Sprinklers must have quick response thermal sensing elements. Sprinkler systems must be wet pipe type.
Product Description Nominal Pipe Size, in.
34,
Pipe
Designation
PT07 PT10 PT12 PT15 PT20 P070710 P100707 P100710 P101007 P121007 P121010 P121012 P121207 P121210 P121215 P151207 P151210 P151507 P151510
Pipe Tee (Soc Soc Soc) Reducer Tee (Soc Soc Soc)
1, 114, 112, 2
3 4
1 114 112 2 3 4 3 4 1 1 34 34 1 3 4 1 1 1 3 4 114 1 34 114 1 1 114 1 114 114 114 34 114 114 1 114 114 112 112 114 34 112 114 1 112 112 34 112 112 1
FM Approvals
1-421
Designation
Product Description
PST101005 PST100705 PST101010 PST121005 PST121205 PST151205 PST151505 PST201505 PST202005 PX07 PX10 PX12 PX15 PX20 PX1007 PL07 PL10 PL12 PL15 PL20 PSL0705
PSL1005 PSL1007 PSL1205 PFL07 PFL10 PFL12 PFL15 PFL20 PK07 PK10 PK12 PK15 PK20 PRK1007 PRK1210 PRK1510 PRK1512 PRK2015 PB1007 PB1207 PB1210 PB1507 PB1510 PB1512 PB2007 PB2010 PB2012 PB2015 PGA12 PGA15 PGA20 PFA07
Sprinkler Head Tee with brass thread insert (Soc Soc Fipt) Cross (Soc Soc Soc Soc) Reducing Cross (Soc Soc Soc Soc) 90 Elbow (Soc Soc) 90 Sprinkler Head Elbow with brass thread insert (Soc Fipt) 45 Elbow (Soc Soc) Coupling (Soc Soc) Reducing Coupling (Soc Soc) Flush Reducer Bushing (Slip Soc) Grooved Coupling Adapter (Soc Pipe OD) Female Adapter with brass thread insert (Soc Fipt) Sprinkler Head Adapter with brass thread insert (Soc Fipt)
112 112 114 112 112 2 2 2 3 4 221 2 2 112 34 34 12 1 1 1 2 1 34 12 111 114 1 12 114 114 12 112 114 12 112 112 12 2 112 12 2 2 1 2 3 4 1 114 112 2 1 1 3 4 3 4
3 4
1 114 112 2 34 12 1 1 2 1 3 4 114 12 3 4 1 114 112 2 3 4 1 114 112 2 1 3 4 114 1 112 1 112 114 2 112 1 3 4 114 34 114 1 112 34 112 1 112 114 2 3 4 21 2 114 2 112 114 1.660 112 1.900 2 2.375 34 34
FM Approvals
1-422
Designation
Product Description
Spigot Sprinkler Head Adapter with brass thread insert (Soc Fipt) Cap (Soc)
1 1 2 1 3 4 34 12 1 1 2 3 4 1 114 112 2
Pipe
IPEX Inc, 3 Place du Commerce, Suite 101, Ile-des-Soeurs Verdun, Quebec H3E 1H7, Canada
BLAZEMASTER CPVC SDR 13.5 pipe and Schedule 80 fittings, joined by solvent cement using BM-5 One Step CPVC solvent cement. For joints using threaded fittings (plastic to plastic, metal to plastic) Teflon tape is recommended. Pressure rating is 175 psi (1205 kPa) at 150F (66C). Approved for exposed use when all of the following criteria are met: Occupancy must be covered in Data Sheet 3-26, Fire Protection Water Demands for Nonstorage Sprinklered Properties, Table 2, Section L, Miscellaneous Non-manufacturing. Sprinklers must have quick response thermal sensing elements. Sprinkler systems must be wet pipe type.
Designation Product Description Nominal Pipe Size, in.
3 4
13401 13404 13406 13415 13411 13416 13417 48472 48473 48474 48030
SDR 13.5 Pipe Sprinkler Head Adapter with brass thread insert (Soc Fipt) Sprinkler Head Adapter with Stl. Stl. Reinforced plastic threads (Spig Fipt) Sprinkler Head Adapter with Stl. Stl. Reinforced plastic threads (Soc Fipt) Sprinkler Head Adapter with Stl. Stl. Reinforced plastic threads (Soc Fipt) Sprinkler Head Adapter with Stl. Stl. Reinforced plastic threads (Soc Fipt) Spigot Sprinkler Head Adapter with brass thread insert (Soc Fipt)
34
1 1 2 1 3 4
3 4
1 2
48024
11
48527
1 1 2
48026
3 4
1 2
48475
3 4
1 2
FM Approvals
1-423
Designation
Product Description
48476 48477
Sprinkler Head Tee with brass thread insert (Soc Soc Fipt) Sprinkler Head Adapter Tee with Stl. Stl. Reinforced plastic threads (Soc Soc Fipt) Sprinkler Head Adapter Tee with Stl. Stl. Reinforced plastic threads (Soc Soc Fipt) Sprinkler Head Adapter Tee with Stl. Stl. Reinforced plastic threads (Fipt Fipt Soc) Reducer Tee (Soc Soc Soc) 90 Sprinkler Head Adapter Elbow with Stl. Stl. Reinforced plastic threads (Soc Fipt) 90 Sprinkler Head Adapter Elbow with Stl. Stl. Reinforced plastic threads (Soc Fipt) 90 Sprinkler Head Elbow with brass thread insert (Soc Fipt) Female Adapter with brass thread insert (Soc Fipt)
3 4
1 1 2 34 12
48012
1 1 12
3 4
34 12
1 2 1
48493 48495 48497 48498 48501 48502 48504 48506 48507 48508 48509 48511 48512 48513 48510 48514 48530 48516 48531 48515 48517 48518 48019
3 4
3 4 1
114 114 1 1 1 4 1 1 112 114 34 112 114 1 112 112 34 112 112 114 112 112 2 2 2 34 112 112 1 221 212 212 1 212 212 114 212 212 112 2 2 112 332 3 3 212
3 4
1 2
48020
1 1 2
3 4
1 2
1 1 2
3 4
1 114
FM Approvals
1-424
Designation
Product Description
48441 48442 48414 48415 48416 48417 48418 48419 48486 48487 48488 48489 48490 48491 48492 48420 48421 48422 48423 48424 48425 48426 48431 48432 48433 48434 48435 48436 48437 48407 48408 48409 48410 48411 48412 48413 48524 48540 48541 48542 48459 48460 48461 48462 48463 48464 48466 48467
Cross (Soc Soc Soc Soc) Tee (Soc Soc Soc) 45 Elbow (Soc Soc) 90 Elbow (Soc Soc) Coupling (Soc Soc) Coupling (Soc Grv) Reducing Bushing (Soc Soc)
112 2
3 4
1 114 112 2 212 3 114 112 2 212 1 3 4 114 34 114 1 1 1 2 3 4 112 1 112 114 21 2 114
FM Approvals
1-425
Designation
Product Description
48468 48469 48470 48471 48400 48401 48402 48403 48404 48405 48406 48443 48444 48445 48446 48447 48448 48449
Soc = Solvent Weld Socket Spig = Spigot End Fipt = Female Iron Pipe Thread
Pipe
5011
5011-R
3 4 1
1 34 34 1 3 4 1
FM Approvals
1-426
Designation
Product Description
5007 90 Elbow (Soc Soc) 5006 45 Elbow (Soc Soc) 5001 Coupling (Soc Soc) 5001-R Reducing Coupling (Soc Soc)
1 1 3 4 114 1 34 114 x 1 x 1 114 x 1 x 114 114 114 34 114 114 1 114 x 114 x 112 112 x 114 x 34 112 x 114 x 1 112 112 34 112 112 1 112 x 112 x 112 112 x 112 x 2 2 2 3 4 221 2 2 112 332
3 4
FM Approvals
1-427
Designation
Product Description
5017
Cap (Soc)
1 114 112 2 212 3 1 3 4 114 34 114 1 112 34 112 1 112 114 2 3 4 21 2 114 2 112 212 114 212 112 212 2 32 3 212
3 4
5018
5035
1 114 1 34 1 34
3 4
5051-H
Flange (Soc)
5019-H
5051-A 5051-2-A
Van Stone Flange (Soc) Van Stone Flange (Spig) Female Adapter with brass thread insert (Soc Fipt)
5003-BI
1 1 1 4 112 2
FM Approvals
1-428
Designation
Product Description
5003-2-BI
Female Adapter with brass thread insert (Spig Fipt) Male Adapter with brass thread insert (Soc Mipt) Female Sprinkler Head Adapter with brass thread insert (Spig x Fipt) Sprinkler Head Tee with brass thread insert (Soc Soc Fipt)
3 4
1
3 4
5004-BI
1 1 1 4 112 2
34
5004-2-S-BI
x 1 2 1 x 1 2
5012-S-BI
34 12 1 34 12 1 1 1 2 111 1 1 2 1
5012R-S-BI
Female Sprinkler Head Reducing Tee with brass thread insert (Soc x Soc x Fipt) 90 Sprinkler Head Elbow with brass thread insert (Soc Fipt)
5007-3-S-BI
Soc = Solvent Weld Socket Spig = Spigot End Fipt = Female Iron Pipe Thread Mipt = Male Iron Pipe Thread
4201-007 4201-010 4201-012 4201-015 4201-020 4201-025 4201-030 4201-102 4201-125 4201-126 4201-131 4201-157 4201-158 4201-159 4201-167 4201-168 4201-169 4201-201 4201-202 4201-210 4201-211 4201-212 4201-213 4201-248 4201-249 4201-251 4201-289 4201-290 4201-291 4201-338 4201-339
1 1 1 4 112 2 2 1 2 3 3 4 1 1 3 4 3 4 1 3 4 1 1 1 34 114 1 34 114 1 1 114 1 114 114 114 34 114 114 1 114 114 112 112 114 34 112 114 1 112 112 34 112 112 1 112 112 114 112 112 2 2 2 34 221 2 2 112 12 212 1 2 212 212 114 212 212 112 332 3 3 212
3 4
FM Approvals
1-429
Designation
Product Description
4202-101 4202-124 4202-130 4202-010 4202-156 4202-166 4202-199 4202-209 4202-237 4202-247 4202-101SR 4202-124SR 4202-130SR 4202-010SR 4202-156SR 4202-166SR 4202-199SR 4202-209SR 4202-211SR 4202-237SR 4202-247SR 4303-122 4203-122SR 4220-007 4220-010 4220-012 4220-015 4220-020 4220-025 4220-030 4220-131 4206-007 4206-010 4206-012 4206-015 4206-020 4206-025 4206-030 4206-131 4207-101 4207-130 4207-131 4207-166 4207-101SR 4207-130SR 4207-131SR 4207-166SR 4217-007 4217-010 4217-012 4217-015 4217-020 4217-025 4217-030 4229-007 4229-010 4229-012 4229-015 4229-020 4229-025 4229-030 4229-131 4229-167 4229-168 4229-210 4229-211 4229-212 4229-248 4229-249 4229-250 4229-251 4229-291 4229-292
34 12 1 3 4 1 2 1 1 12 111 114 1 12 114 114 12 112 114 12 112 112 12 2 112 12 2 2 12 34 12 1 3 4 1 2 1 1 12 111 114 1 12 114 114 12 112 114 12 112 112 12 112 112 1 2 112 12 2 2 12 1 1 2 1 1 1 2 1
3 4 3 4
3 4
Sprinkler Head Tee (Soc Brass FIPT Soc) Sprinkler Head Tee (SocSR FIPTSoc)
1 1 1 4 112 2 2 1 2 3 1 1 34 34
3 4
1 1 1 4 112 2 2 1 2 3
3 4
1 1 1 4 112 2 2 1 2 3 1 3 4 114 34 114 1 1 1 2 3 4 112 1 112 114 2 3 4 21 2 114 2 112 212 112 212 2
FM Approvals
1-430
Designation
Product Description
4237-131 4237-167 4237-168 4237-210 4237-211 4237-212 4237-248 4237-249 4237-250 4237-251 4237-290 4237-291 4237-292 4237-338 4237-339 4233-012 4233-015 4233-020 4235-007 4235-010 4235-012 4235-015 4235-020 4235-007SR 4235-010SR 4235-012SR 4278-007 4278-010 4278-007SR 4278-010SR 4247-007 4247-010 4247-012 4247-015 4247-020 4247-025 4247-030 42001 42011 42001SR 42011SR 42004 42014 42004SR 42014SR 4251-007 4251-010 4251-012 4251-015 4251-020 4251-025 4254-030 4256-007 4256-010 4256-012 4256-015 4256-020 4256-025 4256-030 4253-007 4253-010 4253-012 4253-015 4253-020 4253-025 4253-030 4257-007 4257-010 4257-012 4257-015 4257-020
1 3 4 114 34 114 1 1 1 2 3 4 112 1 112 114 2 3 4 21 2 114 2 112 212 114 212 112 212 2 32 3 212 114 112 2
3 4
1 1 1 4 112 2
3 4
Female Adapters (Soc SR FIPT) Female Adapters (Spig brass FIPT) Female Adapters (Spig SR FIPT)
1 1 1 4
3 4
1
3 4
1
3 4
Cap (Soc)
1 1 1 4 112 2 2 1 2 3
3412
Adjustable Sprinkler Head Adapters (Socbrass FIPT) Adjustable Sprinkler Head Adapters (SocSR FIPT) Adjustable Sprinkler Head Adapters (Spigbrass FIPT Adjustable Sprinkler Head Adapters (SpigSR FIPT)
112
3412
112
3412
112
3412
112
3 4
1 1 1 4 112 2 2 1 2 3
3 4
1 1 1 4 112 2 2 1 2 3
3 4
1 1 1 4 112 2 2 1 2 3
3 4
Union (SocSoc)
1 1 1 4 112 2
FM Approvals
1-431
Designation
Product Description
1 1 1 4 112 2 112
Adapter, Sprinkler Head, Long Body (SocBrass FIPT) Adapter, Sprinkler Head with Positioning Ring (SocBrass FIPT) Adapter, Sprinkler Head (SocBrass FIPT)
R4235-101 4235-101 4235-130 4235-131 4235-101SR 4235-130SR Z4235-101SR Z4235-130SR 4235-131SR 4238-101SR 4238-130SR 4238-101 4238-130 4243-074SR 4243-075SR 4221-101SR 4221-130SR 4221-131SR 4244-007 4244-010 4244-012 4244-015 4244-020 4209-007 4209-010 4209-012 4209-015 4209-020
*Schedule 40 fittings. All other fittings are Schedule 80. Slip = IPS Solvent Weld Socket Spig = Spigot End Fipt = Female Iron Pipe Thread Mipt = Male Iron Pipe Thread
3412
3412
112 134
3412
Adapter, Sprinkler Head (SpigSR FIPT) Adapter, Sprinkler Head (SpigBrass FIPT) Tee, Reducing, Sidewall (SR FIPTSR FIPTSoc) Sprinkler Head Cross (SocSR FIPT)
112
3412
112
121234 12121 3412
112 134
3 4
1 1 1 4 112 2
3 4
1 1 1 4 112 2
Tyco Fire and Building Products, 451 N Cannon Ave, Lansdale PA 19446
BLAZEMASTER. SDR 13.5 CPVC pipe and schedule 40 and 80 fittings, joined by solvent cement method using TFP-400 cement or TFP-500 cement. For joints using threaded fittings (plastic to plastic, plastic to metal) Teflon tape is recommended to obtain a good seal. Pressure rating of pipe and fittings is 175 psi (1205 kPa) at 150F (66C). Approved for exposed use when all of the following criteria are met: Occupancy must be covered in Data Sheet 3-26, Fire Protection Water Demands for Nonstorage Sprinklered Properties, Table 2, Section L, Miscellaneous Non-manufacturing. Sprinklers must have quick response thermal sensing elements. Sprinkler systems must be wet pipe type.
Product Description Nominal Pipe Size, in.
3 4
Pipe STR Sprinklerhead Adapter Both Schedule 40 and 80 Elbow Sprinklerhead Adapter Schedule 40 Sprinklerhead Adapter Schedule 40 Coupling (Slip Slip) 45 Elbow (Slip Slip) 90 Elbow (Slip Slip) Cap (Slip)
3 4
through 3
34
FM Approvals
1-432
Product Description
through 3* through 2*
34 1; 1 34 1; 1 3 4 3 4; 1 1 34; 14 114 34, 1, 112; 1 12 112 34, 1, 114, 2; 1 114 1 34, 1, 114; 112 1 112; 112 114 34, 1; 2 2 34, 1, 114, 112
3 4 34
34
1 1 112 34 12
Reducing Cross Sprinkler Head Adapter 90 Elbow Transition Coupling (Slip Cut Groove) Sprinkler Head Adapter Tee Female Adapter Assembly, Str. (358) Dual Outlet Tee (338)
*34 through 112 in., Schedule 40. 2 through 3 in., Schedule 80.
114, 112, 2 1 1 1, 112 112 12 NPT Slip 2 NPT 2 Slip 212 NPT 3 Slip 3 NPT 1 by 12 (slip by NPT) 1 by 12 (slip by NPT)
SDR 13.5 pipe 90 Elbow (All Socket) 45 Elbow (All Socket) Reducing 90 Elbow (All Socket) Sprinkler Head 90 Elbow (Socket Brass* FIPT)
1, 114, 112, and 2 1, 114, 112, and 2 1, 114, 112, and 2 1 3 4 1 2 1 1 2 1 3 4 114 12 1 2 1 1 2 1 3 4 114 12
3 4 3 4
813
814
Sprinkler Head 90 Elbow (Socket SR FIPT)B Equal Tee (Soc Soc Soc)
820
3 4,
821
822
FM Approvals
1-433
Designation
Product Description
823
3 4
824
825
826 830
Tee, Reducing, Sidewall (SR FIPT SR FIPT Soc) Coupling (Soc Soc)
3 4,
1 2 x 1
1, 114, 112, and 2 1 3 4 114 34 114 1 112 34 112 1 112 114 2 3 4 21 2 114 2 1 1 2 114 112 2
3 4
831
832
835
1 1 1 4 112 2 1 1 34 34
3 4,
836 850
851
852
860 865
34,
FM Approvals
1-434
Fire Resistant Barriers for Use with CPVC Pipe and Fittings in Light Hazard Occupancies
Fire resistant barriers FM Approved for use with CPVC pipe and fittings in Light Hazard Occupancies may be used in place of a fire-resistant barrier with a minimum finish fire rating when tested per ASTM E119 as described under Plastic Pipe and Fittings. These barriers are designed such that once assembled the barrier cannot be removed with ordinary tools.
Soffi-Steel System Fire Resistant Barriers 20 Gauge FM Approved to 10 feet (3.1 m) Ceiling Height
Tyco Fire Products BlazeMaster CPVC Pipe and Fittings IPEX Inc., BlazeMaster CPVC Pipe anf Fittings Harvel BlazeMaster CPVC Pipe Spears Manufacturing Flameguard CPVC Fittings NIBCO Inc., BlazeMaster CPVC Fittings Victaulic Company FireLock CPVC Pipe and Fittings Above pipe and fittings Approved with the following Joint Cements: TFP-500, BM-5, FS-5
Pipe, Fittings and Pipe Joints for Underground Fire Service Mains
Underground fire service mains are made from many different materials. Cast iron, ductile iron, stainless steel pipe, Polyvinyl Chloride (PVC), Polyethylene (PE), and Fiber Reinforced Composite (FRP of Fiberglass) pipe and fittings are acceptable when they are FM Approved. Installation of these products should conform to FM Global Property Loss Prevention Data Sheets.
In-Building Risers
Designed to connect the underground fire service main to the building overhead sprinkler system. The fitting will typically pass under the building foundation and extend up through the floor.
In-Building Riser / SS Riser In-Building Riser / SS Riser In-Building Riser / SS Riser In-Building Riser / SS Riser
4 6 8 10
a, b a, b a, b a, b
a = Stainless steel. b = Available with the following, or combinations of the following, end connections: Grooved, CIPS coupler and Flanged.
4 6 8 10
a, b a, b a, b a, b
a = Stainless steel. b = Available with the following, or combinations of the following, end connections: Grooved CIPS coupler and Flanged.
FM Approvals
1-435
Description
Flanged Pipe with Toruseal Gasket Pipe Pipe Fastite Pipe with Fastite Gasket Pipe Fastite Pipe with Fast-Grip Gasket Pipe Pipe Pipe Pipe Flex-Ring Pipe with Fastite Gasket Pipe Flex-Ring Pipe with Fast-Grip Gasket Pipe Pipe Pipe Pipe
350 (2415) 250 (1725) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 200 (1380) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 200 (1380)
4 6 8, 10, 12 14, 16
4 6 8, 10, 12 14, 16
Ductile iron restraint gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended pipe, fittings or other components.
Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
ASLD ASLD
4, 6, 8, 10, 12 16
ADMB390 ADMB490 ADMB690 ADMB890 ADMB1090 ADMB1290 ADMB1490 ADMB1690 ADMB345 ADMB445 ADMB645 ADMB845 ADMB1045 ADMB1245 ADMB1445 ADMB1645 ADMB322 ADMB422
90 Elbow (M.J.)
3 4
45 Elbow (M.J.)
6 8 10 12 14 16 3 4 6 8 10 12 14 16
2212
Elbow (M.J.)
3 4
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415)
FM Approvals
1-436
Product Designation
Fitting Description
ADMB622 ADMB822 ADMB1022 ADMB1222 ADMB1422 ADMB1622 ADMB311 ADMB411 ADMB611 ADMB811 ADMB1011 ADMB1211 ADMB1411 ADMB1611 ADMR43 ADMR63 ADMR64 ADMR84 ADMR86 ADMR104 ADMR106 ADMR108 ADMR124 ADMR126 ADMR128 ADMR1210 ADMR1410 ADMR166 ADMR168 ADMR1610 ADMR1612 ADMR1614 ADMK3 ADMK4 ADMK6 ADMK8 ADMK10 ADMK12 ADMK14 ADMK16 ADMP3 ADMP4 Solid Plug (M.J.) Solid Cap (M.J.) Reducer 1114 Elbow
6 8 10 12 14 16 3 4 6 8 10 12 14 16 43 63 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 14 10 16 6 16 8 16 10 16 12 16 14 3 4 6 8 10 12 14 16 3 4
350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 250 (1725) 250 (1725) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415)
FM Approvals
1-437
Product Designation
Fitting Description
ADMP6 ADMP8 ADMP10 ADMP12 ADMP14 ADMP16 ADTK3 ADTK4 ADTK6 ADTK8 ADTK10 ADTK12 ADTK16 ADTP3 ADTP4 ADTP6 ADTP8 ADTP10 ADTP12 ADTP16 ADMS3 ADMS4 ADMS6 ADMS8 ADMS10 ADMS12 ADMS14 ADMS16 ADML3 ADML4 ADML6 ADML8 ADML10 ADML12 ADML16 ADG3 ADG4 ADG6 ADG8 ADG10 ADG12 ADG16 M.J. Gland Long Sleeve (M.J.) Long Sleeve (M.J.) Short Sleeve (M.J.) Tapped Plug (M.J.) Tapped Cap (M.J.)
6 8 10 12 14 16 3 4 6 8 10 12 16 3 4 6 8 10 12 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 16 3 4 6 8 10 12 16
350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250
FM Approvals
1-438
Product Designation
Fitting Description
ADMC43 ADMC44 ADMC64 ADMC66 ADMC84 ADMC86 ADMC88 ADMC104 ADMC106 ADMC108 ADMC1010 ADMC124 ADMC126 ADMC128 ADMC1210 ADMC1212 ADMO612 ADMO126 ADMH66 ADMH86 ADMH88 ADMH106 ADMH108 ADMH126 ADMH128 ADMH146 ADMH166 ADMF44 ADMF64 ADMF66 ADMF84 ADMF86 ADMF88 ADMF104 ADMF106 ADMF108 ADMF1010 ADMF124 ADMF126 ADMT33 ADMT43 ADMT44
Cross (M.J.)
43 44 64 66 84 86 88 10 4 10 6 10 8 10 10 12 4 12 6 12 8 12 10 12 12
Offset
6 12 12 6
66 86 8x8 10 6 10x8 12 6 12 8 14 6 16 6
33 43 44
(1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-439
Product Designation
Fitting Description
ADMT63 ADMT64 ADMT66 ADMT84 ADMT86 ADMT88 ADMT104 ADMT106 ADMT108 ADMT1010 ADMT124 ADMT126 ADMT128 ADMT1210 ADMT1212 ADMT143 ADMT144 ADMT146 ADMT148 ADMT1410 ADMT1412 ADMT166 ADMT168 ADMT1610 ADMT1612 ADMT1614 ADMT1616 ADMY33 ADMY43 ADMY44 ADMY63 ADMY64 ADMY66 ADMY83 ADMY84 ADMY86 ADMY88 ADMY103 ADMY104 ADMY106 ADMY108 ADMY1010 45 Wye
63 64 66 84 86 88 10 4 10 6 10 8 10 10 12 4 12 6 12 8 12 10 12 12 14 3 14 4 14 6 14 8 14 10 14 12 16 6 16 8 16 10 16 12 16 14 16 16 3 43 4 63 64 6 83 84 86 88 10 3 10 4 10 6 10 8 10 10
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-440
Product Designation
Fitting Description
ALPR43 ALPR63 ALPR64 ALPR84 ALPR86 ALPR104 ALPR106 ALPR108 ALPR124 ALPR126 ALPR128 ALPR1210 ALPR166 ALPR168 ALPR1612 ASPR43 ASPR63 ASPR64 ASPR84 ASPR86 ASPR104 ASPR106 ASPR108 ASPR124 ASPR126 ASPR128 ASPR1210 ASPR166 ASPR168 ASPR1612 APPR43 APPR64 APPR84 APPR86 APPR104 APPR106 APPR108 APPR124 APPR126 APPR128 APPR1210 APPR166
43 6x3 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 16 6 16 8 16 12
43 6x3 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 16 6 16 8 16 12
43 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 16 6
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725)
FM Approvals
1-441
Product Designation
Fitting Description
APPR168 APPR1612 AMFA3 AMFA4 AMFA6 AMFA8 AMFA10 AMFA12 ADTT3 ADTT4 ADTT6 ADTT8 ADTT10 ADTT12 ADTT16 ADTC4 ADTC6 ADTC8 ADTC10 ADTC12 ADTC16 ADFB390 ADFB490 ADFB690 ADFB890 ADFB1090 ADFB1290 ADFB345 ADFB445 ADFB645 ADFB845 ADFB1045 ADFB1245 ADFB322 ADFB422 ADFB622 ADFB822 ADFB1022 ADFB1222 ADFB311 ADFB411 ADFB611 ADFB811 ADFB1011 ADFB1211 ADFB32 ADFB43 ADFB63 ADFB64 ADFB65 ADFB84 ADFB85 ADFB86 ADFB104 ADFB106 ADFB108 ADFB124 ADFB126 ADFB128 90 Elbow (Flanged) Tapped Cross Tapped Tees Adapter Flanged End M.J.
16 8 16 12 3 4 6 8 10 12 3 4 6 8 10 12 16 4 6 8 10 12 16 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 32 43 63 64 65 84 85 86 10 4 10 6 10 8 12 4 12 6 12 8
250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 250 (1750)
45 Elbow (Flanged)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-442
Product Designation
Fitting Description
ADFB1210 ADFL390 ADFL490 ADFL690 ADFL890 ADFL1090 ADFL1290 ADFD3 ADFD4 ADFD6 ADFD8 ADFD10 ADFD12 ADFT33 ADFT44 ADFT55 ADFT66 ADFT88 ADFT1010 ADFT1212 ADFT32 ADFT42 ADFT425 ADFT43 ADFT62 ADFT63 ADFT64 ADFT84 ADFT86 ADFT104 ADFT106 ADFT108 ADFT124 ADFT126 ADFT128 ADFT1210 ADRT433 ADRT533 ADRT544 ADRT633 ADRT644 ADRT646 ADRT864 ADRT866 ADRT868 ADFC33 ADFC44 ADFC55 ADFC66 ADFC88 ADFC1010 ADFC1212 ADFC32 ADFC42 ADFC425 ADFC43 ADFC62 ADFC63 ADFC64 ADFC84 ADFC86 ADFC104 ADFC106 ADFC108 ADFC124 ADFC126 ADFC128 ADFC1210 ADFR32 ADFR325 ADFR42 ADFR425 ADFR43 ADFR62 ADFR625
12 10 3 4 6 8 10 12 3 4 6 8 10 12 3 4 5 6 8 10 12 32 42 4 212 43 62 63 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 433 533 544 644 644 646 864 866 868 3 4 5 6 8 10 12 32 42 4 212 43 62 63 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 32 3 212 42 4 212 43 62 6 212
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-443
Product Designation
Fitting Description
ADFR63 ADFR64 ADFR65 ADFR84 ADFR85 ADFR86 ADFR104 ADFR106 ADFR108 ADFR124 ADFR126 ADFR128 ADFR1210 ADFE32 ADFE325 ADFE42 ADFE425 ADFE43 ADFE62 ADFE625 ADFE63 ADFE64 ADFE84 ADFE85 ADFE86 ADFE104 ADFE106 ADFE108 ADFE124 ADFE126 ADFE128 ADFE1210 ADTF3 ADTF4 ADTF6 ADTF8 ADTF10 ADTF12 ABDF3 ABDF4 ABDF6 ABDF8 ABDF10 ABDF12
250 (1750)
250 (1750)
250 (1750)
250 (1750)
All above products used to join plain-end or mechanical joint or flanged ductile iron pipe to mechanical joint or flanged or plain end devices as noted or to identical adapters in underground mains. Full Body Mechanical Joint Pipe Fittings
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
AXMB390 AXMB490 AXMB690 AXMB890 AXMB1090 AXMB1290 AXMB345 AXMB445 AXMB645 AXMB845 AXMB1045 AXMB1245
90 Elbow
3 4 6 8 10 12
45 Elbow
3 4 6 8 10 12
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-444
Product Designation
Fitting Description
AXMB322 AXMB422 AXMB622 AXMB822 AXMB1022 AXMB1222 AXMB311 AXMB411 AXMB611 AXMB811 AXMB1011 AXMB1211 AXME390 AXME490 AXME690 AXME890 AXME1090 AXME1290 AXME345 AXME445 AXME645 AXME845 AXME1045 AXME1245 AXME322 AXME422 AXME622 AXME822 AXME1022 AXME1222 AXME311 AXME411 AXME611 AXME811 AXME1011 AXME1211 AXMT43 AXMT44 AXMT63 AXMT64 AXMT66 AXMT83
2212 Elbow
3 4 6 8 10 12
1114 Elbow
3 4 6 8 10 12
3 4 6 8 10 12
3 4 6 8 10 12
2212
Elbow
3 4 6 8 10 12
1114
Elbow
3 4 6 8 10 12
Tee
43 4 63 64 6 83
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-445
Product Designation
Fitting Description
AXMT84 AXMT86 AXMT88 AXMT103 AXMT104 AXMT106 AXMT108 AXMT1010 AXMT123 AXMT124 AXMT126 AXMT128 AXMT1210 AXMT1212 AXMT143 AXMT144 AXMT146 AXMT148 AXMT1410 AXMT1412 AXMT1414 AXMT163 AXMT164 AXMT166 AXMT168 AXMT1610 AXMT1612 AXMT1614 AXMT1616 AXMC33 AXMC43 AXMC44 AXMC63 AXMC64 AXMC66 AXMC84 AXMC86 AXMC88 AXMC104 AXMC106 AXMC108 AXMC1010 Cross (M.J. M.J.)
84 86 8 103 104 106 108 10 123 124 126 128 1210 12 143 144 146 148 1410 1412 14 163 164 166 168 1610 1612 1614 16 3x3 43 4x4 63 64 66 84 86 8x8 104 106 108 10x10
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-446
Product Designation
Fitting Description
AXMC124 AXMC126 AXMC128 AXMC1210 AXMC1212 AXMH64 AXMH66 AXMH84 AXMH86 AXMH88 AXMH104 AXMH106 AXMH108 AXMH1010 AXMH124 AXMH126 AXMH128 AXMH1210 AXMH1212 AXMF44 AXMF64 AXMF66 AXMF84 AXMF86 AXMF88 AXMF104 AXMF106 AXMF108 AXMF1010 AXMF124 AXMF126 AXMF128 AXMF1210 AXMF1212 AXMR43 AXMR63 AXMR64 AXMR84 AXMR86 AXMR104 AXMR106 AXMR108 Reducer (M.J. M.J.) Tee (M.J. M.J. Flanged End) Hydrant Tee (M.J. M.J. Swivel End)
124 126 128 1210 12x12 6x4 6x6 8x4 8x6 8x8 10x4 10x6 10x8 10x10 12x4 12x6 12x8 12x10 12x12 4x4 6x4 6x6 8x4 8x6 8x8 10x4 10x6 10x8 10x10 12x4 12x6 12x8 12x10 12x12 43 63 64 84 86 104 106 108
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-447
Product Designation
Fitting Description
AXMR124 AXMR126 AXMR128 AXMR1210 AXSPR43 AXSPR63 AXSPR64 AXSPR84 AXSPR86 AXSPR104 AXSPR106 AXSPR108 AXSPR124 AXSPR126 AXSPR128 AXSPR1210 AXLPR43 AXLPR63 AXLPR64 AXLPR84 AXLPR86 AXLPR104 AXLPR106 AXLPR108 AXLPR124 AXLPR126 AXLPR128 AXLPR1210 AXMFA6 AXMFA8 AXMFA10 AXMFA12 AXMS3 AXMS4 AXMS6 AXMS8 AXMS10 AXMS12 AXMS14 AXMS16 AXML3 AXML4 Long Sleeve (M.J. M.J.) Short Sleeve (M.J. M.J.) Flange Adapter( M.J. Flange) Reducer (M.J. P.E.) Reducer (P.E. M.J.)
124 126 128 1210 4x3 6x3 6x4 8x4 8x6 10x4 10x6 10x8 12x4 12x6 12x8 12x10 4x3 6x3 6x4 8x4 8x6 10x4 10x6 10x8 12x4 12x6 12x8 12x10 6 8 10 12 3 4 6 8 10 12 14 16 3 4
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-448
Product Designation
Fitting Description
AXML6 AXML8 AXML10 AXML12 AXML14 AXML16 AXMK3 AXMK4 AXMK6 AXMK8 AXMK10 AXMK12 AXMK14 AXMK16 AXTK3 AXTK4 AXTK6 AXTK8 AXTK10 AXTK12 AXTK14 AXTK16 AXMP3 AXMP4 AXMP6 AXMP8 AXMP10 AXMP12 AXMP14 AXMP16 AXTP3 AXTP4 AXTP6 AXTP8 AXTP10 AXTP12 AXTP14 AXTP16 Tapped Plug Plug Tapped Cap Cap
6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
ADPB390
90 Elbow
350 (2415)
FM Approvals
1-449
Product Designation
Fitting Description
ADPB490 ADPB690 ADPB890 ADPB1090 ADPB345 ADPB445 ADPB645 ADPB845 ADPB1045 ADPB322 ADPB422 ADPB622 ADPB822 ADPB1022 ADPB311 ADPB411 ADPB611 ADPB811 ADPB1011 ADPF44 ADPF64 ADPF66 ADPF86 ADPF88 ADPF103 ADPF106 ADPF108 ADPF126 ADPF128 ADPY 44 ADPY 63 ADPY 64 ADPY 66 APFA6 APFA8 APFA10 APFA12 APR84 Reducer (Push-On Push-On) Flange Adapter (Push-On Flange) 45 Wye Tee (Push-OnFlange) 1114 Elbow 2212 Elbow 45 Elbow
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
AXPB390
90 Elbow
350 (2415)
FM Approvals
1-450
Product Designation
Fitting Description
AXPB490 AXPB690 AXPB890 AXPB1090 AXPB1290 AXPB345 AXPB445 AXPB645 AXPB845 AXPB1045 AXPB1245 AXPB322 AXPB422 AXPB622 AXPB822 AXPB1022 AXPB1222 AXPB311 AXPB411 AXPB611 AXPB811 AXPB1011 AXPB1211 AXPT44 AXPT63 AXPT64 AXPT66 AXPT83 AXPT84 AXPT86 AXPT88 AXPT103 AXPT104 AXPT106 AXPT108 AXPT1010 AXPT123 AXPT124 AXPT126 AXPT128 AXPT1210 AXPT1212 Tee 1114 Elbow 2212 Elbow 45 Elbow
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-451
Product Designation
Fitting Description
AXPF44 AXPF63 AXPF64 AXPF66 AXPF83 AXPF84 AXPF86 AXPF88 AXPF103 AXPF104 AXPF106 AXPF108 AXPF1010 AXPF123 AXPF124 AXPF126 AXPF128 AXPF1210 AXPF1212 AXPFA4 AXPFA6 AXPFA8 AXPFA10 AXPFA12 AXPK3 AXPK4 AXPK6 AXPK8 AXPTK3 AXPTK4 AXPTK6 AXPTK8 AXPP3 AXPP4 AXPP6 AXPP8 AXPTP3 AXPTP4 AXPTP6 AXPTP8
4x4 6x3 6x4 6x6 8x3 8x4 8x6 8x8 10x3 10x4 10x6 10x8 10x10 12x3 12x4 12x6 12x8 12x10 12x12
4 6 8 10 12
Cap
3 4 6 8
Tapped Cap
3 4 6 8
Plug
3 4 6 8
Tapped Plug
3 4 6 8
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-452
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Ductile Iron Grooved Fittings
Product Designation Fitting Description Nominal Pipe Size, in.
250 psi (1725 kPa) for 3 thru 12 in. sizes 175 psi (1205 kPa) for 14 and 16 in. sizes
3, 4, 6, 8 and 10
175 (1205)
Flex 900
3, 4, 6, 8, 10 12
Extend 200
3, 4, 6, 8, 10 12
1100
3, 4, 6, 8, 10, 12
300 (2070) 250 (1725) 200 (1380) 300 (2070) 250 (1725) 200 (1380) 175 (1205)
a, b a, b a, b a, b a, b a, b c
a. Can be assembled to order in any combination of Flex 900 Swivel and Extend 200 Expansion Joints. b. Flanged or S.M.J. end connections. c. Ductile iron restraint gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended pipe fitting or other components.
Griffin Pipe Products Co, 10 Adams St, Upper Basin, Lynchburg VA 24505
Pressure rating 350 psi (2415) Product Description Nominal Pipe Size, in.
Remarks
Pipe
3 through 16 3 through 16 16 16
*Min thickness in 4 in. size, Class Class 350 Available in Tyton Joint Class 250 Available in Tyton Joint Class 300 Available in Tyton Joint
51 Ends 3 through 16 in., or Mechanical Joint Ends 3 through 16 in., 350 psi (2415 kPa) pressure rating. Ends 16 in., 250 psi (1725 kPa) Ends 16 in., 300 psi (2070 kPa)
FM Approvals
1-453
Notes:
Thrust-Lock Pipe Thickness Class 350, 50, 51, 52, 53, 54, 55, 56 Thrust-Lock Pipe Thickness Class 250, 300, 350, 50, 51, 52, 53, 54, 55, 56 Thrust-Lock Pipe Thickness Class 250, 300, 350, 50, 51, 52, 53, 54, 55, 56 Thrust-Lock Pipe Thickness Class 150, 200, 250, 300, 350, 50, 51, 52, 53, 54, 55, 56 Fastite Pipe Thickness Class 150, 200, 250, 300, 350, 50, 51, 52, 53, 54, 55, 56 Mechanical Joint Pipe, Class 50 Push-On Joint Pipe, Class 50
Notes: a. FM Approved with normal lock ring and gripper ring (for field cut joints).
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
a a
Romac Industries Inc, 21919 20th Ave SE, Suite 100, Bothell WA 98021-4446
Ductile iron restraint gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended pipe fitting or other components.
Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12
Ductile Iron Adapter Flanges used to secure plain-ended DI pipe to flange ended devices in underground mains or at the base of a sprinkler riser. Series RFCA Adapter Flanges 3, 4, 6, 8, 10, 12 175 (1205)
FlexiJoints are flexible expansion joints. Available with two articulated ball ends to accommodate pipeline deflection, settlement, and expansion. Available with Flanged or Mechanical Joint end connections, or a combination. Also available with a single articulated ball end to accommodate pipeline deflection and expansion. Available with Flanged or Mechanical Joint end connections, or a combination.
Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
3, 4, 6 8, 10 12
Pipe Standard Pipe Standard Push-On (unrestrained) Standard Vi self-restrained gasket 100 through 300 100, 125 150 200, 250, 300 25 (363) 20 (290) 16 (232) 14 (203)
FM Approvals
1-454
Description
25 22 20 16
Express Pipe Express unrestrained mechanical joint 100 through 300 25 (363)
Fittings Double Socket Double Socket Double Socket Double Socket All Socket Tee 90 Elbow 45 Elbow 2212 Elbow 1114 Elbow 100 through 300 100 through 300 100 through 300 100 through 300 300300300 300300250 300300200 300300150 300300100 250250250 250250200 250250150 250250100 200200200 200200150 200200125 200200100 150150150 150150125 150150100 125125125 125125100 100100100 300300300 300300250 300300200 300300150 300300100 250250250 250250200 250250150 250250100 200200200 200200150 200200125 200200100 150150150 150150125 150150100 125125125 125125100 100100100 25 25 25 25 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 (363) (363) (363) (363) (290) (290) (290) (290) (290) (290) (290) (290) (290) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (290) (290) (290) (290) (290) (290) (290) (290) (290) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b)
300250 300200 300150 250200 250150 250125 200150 200125 200100 150125 150100 125100
25 25 25 25 25 25 25 25 25 25 25 25
(363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363)
(a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a), (a),
(b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b) (b)
FM Approvals
1-455
Description
Socket Fitting 90 Elbow 45 Elbow 2212 Elbow 1114 Elbow 90 Duckfoot Elbow
25 25 25 25 25 25 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25
(363) (363) (363) (363) (363) (363) (290) (290) (290) (290) (290) (290) (290) (290) (290) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363) (363)
(a), (b)
Flanged Tees
300x300x300 300x300x250 300x300x200 300x300x150 300x300x100 250x250x250 250x250x200 250x250x150 250x250x100 200x200x200 200x200x150 200x200x125 200x200x100 150x150x150 150x150x125 150x150x100 125x125x125 125x125x100 100x100x100 300250 300200 300150 250200 250150 250125 200150 200125 200100 150125 150100 125100 100 through 300 250100 200125 200100 300200 300150 300100 100 through 300 100 125 through 300
(c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c) (c)
Flanged Reducer
Notes:
100, 125 150 200, 250, 300 100, 125, 150 200 250 300
20 16 14 14 25 22 20 16
FM Approvals
1-456
Sigma Corp, Rte 537 Goldman Dr, Box 300, Cream Ridge NJ 08514
Ductile iron restraint gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended pipe, fittings or other components.
Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
SLD SLD
4, 6, 8, 10, 12 16
DMB290 DMB390 DMB490 DMB690 DMB890 DMB1090 DMB1290 DMB1490 DMB1690 DMB345 DMB445 DMB645 DMB845 DMB1045 DMB1245 DMB1445 DMB1645 DMB322 DMB422 DMB622 DMB822 DMB1022 DMB1222 DMB1422 DMB1622 DMB311 DMB411 DMB611 DMB811 DMB1011 DMB1211 DMB1411 DMB1611
90 Elbow (M.J.)
2 3 4 6 8 10 12 14 16
45 Elbow (M.J.)
3 4 6 8 10 12 14 16
3 4 6 8 10 12 14 16
1114 Elbow
3 4 6 8 10 12 14 16
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415)
3 4 6
FM Approvals
1-457
Product Designation
Fitting Description
DME890 DME1090 DME1290 DME345 DME445 DME645 DME845 DME1045 DME1245 DME322 DME422 DME622 DME822 DME1022 DME1222 DME311 DME411 DME611 DME811 DME1011 DME1211 MFB390 MFB490 MFB690 MFB890 MFB1090 MFB1290 MFB345 MFB445 MFB645 MFB845 MFB1045 MFB1245 MFB322 MFB422 MFB622 MFB822 MFB1022 MFB1222 MFB311 MFB411 MFB611 MFB811 MFB1011 MFB1211 SSB6 SSB8 SSB10 DMR42 DMR43 DMR63 DMR64 DMR84 DMR86 DMR104 Reducer 90 Elbow (Swivel End Swivel End) 1114 Elbow (MJ Flanged End) 2212 Elbow (MJ Flanged End) 45 Elbow (MJ Flanged End) 90 Elbow (MJ Flanged End) 1114 Elbow (MJ PE) 2212 Elbow (MJ PE) 45 Elbow (MJ PE)
8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 6 8 10 42 43 63 64 84 86 104 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-458
Product Designation
Fitting Description
DMR106 DMR108 DMR124 DMR126 DMR128 DMR1210 DMR1410 DMR1412 DMR166 DMR168 DMR1610 DMR1612 DMR1614 DMK3 DMK4 DMK6 DMK8 DMK10 DMK12 DMK14 DMK16 DMK18 DMP3 DMP4 DMP6 DMP8 DMP10 DMP12 DMP14 DMP16 DTK3 DTK4 DTK6 DTK8 DTK10 DTK12 DTK14 DTK14 DTK16 DTK18 DTP3 DTP4 Tapped Plug (M.J.) Tapped Cap (M.J.) Solid Plug (M.J.) Solid Cap (M.J.)
106 108 124 126 128 1210 1410 1412 166 168 1610 1612 1614 3 4 6 8 10 12 14 16 18 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 14 16 18 3 4
350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 250 (1725) 250 (1725) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 350 (2415) 250 (1725) 250 (1725) 350 (2415) 350 (2415)
FM Approvals
1-459
Product Designation
Fitting Description
DTP6 DTP8 DTP10 DTP12 DTP14 DTP16 DMS3 DMS4 DMS6 DMS8 DMS10 DMS12 DMS14 DMS16 DML2 DML3 DML4 DML6 DML8 DML10 DML12 DML14 DML16 DG2 DG3 DG4 DG6 DG8 DG10 DG12 DG16 DMC33 DMC43 DMC44 DMC64 DMC66 DMC84 DMC86 DMC88 DMC104 DMC106 DMC108 Cross (M.J.) M.J. Gland Long Sleeve (M.J.) Short Sleeve (M.J.)
350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-460
Product Designation
Fitting Description
DMC1010 DMC124 DMC126 DMC128 DMC1210 DMC1212 DMC1612 DMC1616 DMO612 DMO126 DMH64 DMH66 DMH84 DMH86 DMH88 DMH104 DMH106 DMH108 DMH1010 DMH124 DMH126 DMH128 DMH1210 DMH1212 DMH146 DMH166 DMF44 DMF64 DMF66 DMF84 DMF86 DMF88 DMF104 DMF106 DMF108 DMF1010 DMF124 DMF126 DMF128 DMF1210 DMF1212 DMF146 Hydrant Tee (M.J.) Hydrant Tee (M.J. M.J. Flanged End) Hydrant Tee (M.J. M.J. Swivel End) Offset
1010 124 126 128 1210 1212 1612 1616 612 126 64 66 84 86 8x8 10 4 106 10x8 10x10 12 4 126 128 12 10 12 12 146 166 44 6x4 66 8x4 86 88 10x4 106 10x8 10x10 12x4 126 128 1210 1212 146
350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-461
Product Designation
Fitting Description
DMF166 DMF168 DMT22 DMT33 DMT43 DMT44 DMT63 DMT64 DMT66 DMT83 DMT84 DMT86 DMT88 DMT103 DMT104 DMT106 DMT108 DMT1010 DMT124 DMT126 DMT128 DMT1210 DMT1212 DMT143 DMT144 DMT146 DMT148 DMT1410 DMT1412 DMT1414 DMT166 DMT168 DMT1610 DMT1612 DMT1614 DMT1614 DMT1616 DMT1616 DMY33 DMY43 DMY44 DMY63 45 Wye
166 168 22 33 43 44 63 64 66 83 84 86 88 103 104 106 108 1010 124 126 128 1210 1212 143 144 146 148 1410 1412 1414 166 168 1610 1612 1614 1614 1616 1616 33 43 44 63
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-462
Product Designation
Fitting Description
DMY64 DMY66 DMY83 DMY84 DMY86 DMY88 DMY103 DMY104 DMY106 DMY108 DMY1010 DMY123 DMY124 DMY126 DMY128 DMY1210 DMY1212 LPR43 LPR63 LPR64 LPR84 LPR86 LPR104 LPR106 LPR108 LPR124 LPR126 LPR128 LPR1210 LPR166 LPR168 LPR1612 SPR43 SPR63 SPR64 SPR84 SPR86 SPR104 SPR106 SPR108 SPR124 SPR126 Reducer (P.E. M.J.) Reducer (M.J. P.E.)
64 66 83 84 86 88 103 104 106 108 1010 123 124 126 128 1210 1212 43 6x3 64 84 86 104 106 108 124 126 128 1210 166 168 1612 43 6x3 64 84 86 104 106 108 124 126
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070)
FM Approvals
1-463
Product Designation
Fitting Description
SPR128 SPR1210 SPR166 SPR168 SPR1612 PPR43 PPR63 PPR64 PPR84 PPR86 PPR104 PPR106 PPR108 PPR124 PPR126 PPR128 PPR1210 PPR166 PPR168 PPR1612 MFA3 MFA4 MFA6 MFA8 MFA10 MFA12 MFA14 MFA16 MFB490 MFB690 MFB890 MFB1090 MFB1290 MFB645 MFB845 MFB1045 MFB1245 DTT3 DTT4 DTT6 DTT8 DTT10 Tapped Tees 45 Bend MJ Flange 90 Bend MJ Flange Adapter Flanged End M.J. Reducer Plain Ends
128 1210 166 168 1612 43 63 64 84 86 104 106 108 124 126 128 1210 166 168 1612 3 4 6 8 10 12 14 16 4 6 8 10 12 6 8 10 12 3 4 6 8 10
300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-464
Product Designation
Fitting Description
DTT12 DTT16 DTC4 DTC6 DTC8 DTC10 DTC12 DTC16 SG6 SG8 SSA613 SSA813 Solid Swivel Adapter Solid Swivel Adapter Swivel Gland Tapped Cross
12 16 4 6 8 10 12 16 6 8 6 8
300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
DFB390 DFB490 DFB590 DFB690 DFB890 DFB1090 DFB1290 DFB345 DFB445 DFB545 DFB645 DFB845 DFB1045 DFB1245 DFB322 DFB422 DFB522 DFB622 DFB822 DFB1022 DFB1222 DFB311 DFB411 DFB511 DFB611 DFB811 DFB1011 DFB1211 DFB32 DFB43 DFB63 DFB64 DFB65 DFB84 DFB85 DFB86 DFB104 DFB106 DFB108 DFB124 DFB126 DFB128 DFB1210 DFL390 DFL490 DFL590 DFL690 DFL890
90 Elbow (Flanged)
45 Elbow (Flanged)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-465
Product Designation
Fitting Description
DFL1090 DFL1290 DFD3 DFD490 DFD590 DFD690 DFD890 DFD1090 DFD1290 DFD108 DFT33 DFT44 DFT55 DFT66 DFT88 DFT1010 DFT1212 DFT32 DFT42 DFT425 DFT43 DFT62 DFT63 DFT64 DFT83 DFT84 DFT86 DFT103 DFT104 DFT106 DFT108 DFT123 DFT124 DFT126 DFT128 DFT1210 DRT433 DRT533 DRT544 DRT633 DRT644 DRT646 DRT864 DRT866 DRT868 DFC33 DFC44 DFC55 DFC66 DFC88 DFC1010 DFC1212 DFC32 DFC42 DFC425 DFC43 DFC62 DFC63 DFC64 DFC84 DFC86 DFC104 DFC106 DFC108 DFC124 DFC126 DFC128 DFC1210 DFY44 DFY55 DFY66 DFY88 DFY1010 DFY1212
10 12 3 4 5 6 8 10 12 108 3 4 5 6 8 10 12 32 42 4212 43 62 63 64 83 84 86 103 104 106 108 123 124 126 128 1210 433 533 544 644 644 646 864 866 868 3 4 5 6 8 10 12 32 42 4212 43 62 63 64 84 86 104 106 108 124 126 128 1210 4 5 6 8 10 12
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-466
Product Designation
Fitting Description
DFW44 DFW66 DFW88 DFW1010 DFW1212 DFR32 DFR325 DFR42 DFR425 DFR43 DFR62 DFR625 DFR63 DFR64 DFR65 DFR84 DFR85 DFR86 DFR104 DFR106 DFR108 DFR124 DFR126 DFR128 DFR1210 DFR1612 DFE32 DFE325 DFE42 DFE425 DFE43 DFE62 DFE625 DFE63 DFE64 DFE65 DFE84 DFE85 DFE86 DFE104 DFE106 DFE108 DFE124 DFE126 DFE128 DFE1210 DTF3 DTF4 DTF6 DTF8 DTF10 DTF12 BDF3 BDF4 BDF6 BDF8 BDF10 BDF12 BDF14 BDF20 DFA4 DFA6 DFA8 DFA10 DFA12 DFA4 DFA6 DFA8 DFA10 DFA12 DFW33 DFW44 DFW66 DFW88 DFW1010
4 6 8 10 12 32 3212 42 4212 43 62 6212 63 64 65 84 85 86 104 106 108 124 126 128 1210 1612 32 3212 42 4212 43 62 6212 63 64 65 84 85 86 104 106 108 124 126 128 1210 3 4 6 8 10 12 3 4 6 8 10 12 14 20 4 6 8 10 12 4 6 8 10 12 33 44 66 88 1010
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1725)
250 (1725)
FM Approvals
1-467
Product Designation
Fitting Description
DFW1212
1212
All above products used to join plain-end or mechanical joint or flanged ductile iron pipe to mechanical joint or flanged or plain end devices as noted or to identical adapters in underground mains. Full Body Mechanical Joint Pipe Fittings
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
XMB390 XMB490 XMB690 XMB890 XMB1090 XMB1290 XMB345 XMB445 XMB645 XMB845 XMB1045 XMB1245 XMB1645 XMB322 XMB422 XMB622 XMB822 XMB1022 XMB1222 XMB311 XMB411 XMB611 XMB811 XMB1011 XMB1211 XME390 XME490 XME690 XME890 XME1090 XME1290 XME345 XME445 XME645 XME845 XME1045 XME1245 XME322 XME422 XME622 XME822 XME1022 XME1222 XME311 XME411 XME611 XME811 XME1011 XME1211 XMT43 XMT44 XMT63 XMT64 XMT66 XMT83 XMT84 XMT86 XMT88 XMT103 XMT104 XMT106 XMT108 XMT1010 XMT123 XMT124 XMT126
90 Elbow
45 Elbow
2212 Elbow
1114 Elbow
Tee
350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
FM Approvals
1-468
Product Designation
Fitting Description
XMT128 XMT1210 XMT1212 XMT143 XMT144 XMT146 XMT148 XMT1410 XMT1412 XMT1414 XMT163 XMT164 XMT166 XMT168 XMT1610 XMT1612 XMT1614 XMT1616 XMC33 XMC43 XMC44 XMC63 XMC64 XMC66 XMC84 XMC86 XMC88 XMC104 XMC106 XMC108 XMC1010 XMC124 XMC126 XMC128 XMC1210 XMC1212 XMH64 XMH66 XMH84 XMH86 XMH88 XMH104 XMH106 XMH108 XMH1010 XMH124 XMH126 XMH128 XMH1210 XMH1212 XMF44 XMF64 XMF66 XMF84 XMF86 XMF88 XMF104 XMF106 XMF108 XMF1010 XMF124 XMF126 XMF128 XMF1210 XMF1212 XMR43 XMR63 XMR64 XMR84 XMR86 XMR104 XMR106 XMR108 XMR124
128 1210 1212 143 144 146 148 1410 1412 1414 163 164 166 168 1610 1612 1614 1616 33 43 44 63 64 66 84 86 88 104 106 108 1010 124 126 128 1210 1212 64 66 84 86 88 104 106 108 1010 124 126 128 1210 1212 44 64 66 84 86 88 104 106 108 1010 124 126 128 1210 1212 43 63 64 84 86 104 106 108 124
350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
FM Approvals
1-469
Product Designation
Fitting Description
XMR126 XMR128 XMR1210 XSPR43 XSPR63 XSPR64 XSPR84 XSPR86 XSPR104 XSPR106 XSPR108 XSPR124 XSPR126 XSPR128 XSPR1210 XLPR43 XLPR63 XLPR64 XLPR84 XLPR86 XLPR104 XLPR106 XLPR108 XLPR124 XLPR126 XLPR128 XLPR1210 XMFA6 XMFA8 XMFA10 XMFA12 XMS3 XMS4 XMS6 XMS8 XMS10 XMS12 XMS14 XMS16 XML3 XML4 XML6 XML8 XML10 XML12 XML14 XML16 XML20 XMK3 XMK4 XMK6 XMK8 XMK10 XMK12 XMK14 XMK16 XTK3 XTK4 XTK6 XTK8 XTK10 XTK12 XTK14 XTK16 XMP3 XMP4 XMP6 XMP8 XMP10 XMP12 XMP14 XMP16 XTP3 XTP4 XTP6
Cap
Tapped Cap
Plug
Tapped Plug
126 128 1210 43 63 64 84 86 104 106 108 124 126 128 1210 43 63 64 84 86 104 106 108 124 126 128 1210 6 8 10 12 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 20 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6
350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
FM Approvals
1-470
Product Designation
Fitting Description
8 10 12 14 16
Compact Push-On Pipe Fittings When used with US Pipe FieldLok 350 gaskets as a joint restraint, the pressure rating is 250 psi (1725 kPa).
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
DPB390 DPB490 DPB690 DPB890 DPB1090 DPB1290 DPB345 DPB445 DPB645 DPB845 DPB1045 DPB1245 DPB1645 DPB322 DPB422 DPB622 DPB822 DPB1022 DPB1222 DPB1622 DPB311 DPB411 DPB611 DPB811 DPB1011 DPB1211 DPB1611 PFB490 PFB690 PFB890 PFB445 PFB1045 PFB422 PFB622 PFB822 PFB1222 PFB411 PFB611 DPT44 DPT84 DPT86 DPT88 DPT1010 DPT1212 DPT166 DPT168 DPT1612 DPT1616 DPF44 DPF64 DPF66 DPF84
90 Elbow
3 4 6 8 10 12 3 4 6 8 10 12 16 3 4 6 8 10 12 16 3 4 6 8 10 12 16 4 6 8
350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
45 Elbow
2212 Elbow
1114 Elbow
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 350 350 350 350 350 350 350 350 350 350 350 350 350 (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
4 10
4 6 8 12
4 6
Tee
FM Approvals
1-471
Product Designation
Fitting Description
DPF86 DPF88 DPF103 DPF106 DPF108 DPF126 DPF128 DPF1210 DPF166 DPF168 PFF66 PFF86 PFF88 PFF106 DPC86 DPC128 DPY DPY DPY DPY DPY DPY DPY 44 63 64 66 86 88 104 Tee (Push-on Flange Flange)
86 88 103 106 108 126 128 1210 166 168 6 86 8 106 86 128 44 63 64 66 86 88 104 4 6 8 10 12 64 84 86 106 108 128 168 1610 1612 86 4 6 8 10 12 16 4 6 8 10 12 6 8 6 8
350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
Cross
350 (2415) 350 (2415) 350 350 350 350 250 250 250 350 350 350 350 350 350 350 350 350 350 350 350 350 350 (2415) (2415) (2415) (2415) (1725) (1725) (1725) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
45 Wye
PFA4 PFA6 PFA8 PFA10 PFA12 DPR64 DPR84 DPR86 DPR106 DPR108 DPR128 DPR168 DPR1610 DPR1612 PFR86 DPP4 DPP6 DPP8 DPP10 DPP12 DPP16 PTP4 PTP6 PTP8 PTP10 PTP12 DPK6 DPK8 PTK6 PTK8
350 (2415) 350 350 350 350 350 350 350 350 350 350 350 (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
Tapped Plug
Cap
Tapped Cap
Full Body Push-On Pipe Fittings When used with US Pipe FieldLok 350 gaskets as a joint restraint, the pressure rating is 250 psi (1725 kPa).
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
90 Elbow
3 4 6 8 10 12
FM Approvals
1-472
Product Designation
Fitting Description
XPB345 XPB445 XPB645 XPB845 XPB1045 XPB1245 XPB322 XPB422 XPB622 XPB822 XPB1022 XPB1222 XPB311 XPB411 XPB611 XPB811 XPB1011 XPB1211 XPT44 XPT63 XPT64 XPT66 XPT83 XPT84 XPT86 XPT88 XPT103 XPT104 XPT106 XPT108 XPT1010 XPT123 XPT124 XPT126 XPT128 XPT1210 XPT1212 XPF44 XPF63 XPF64 XPF66 XPF83 XPF84 XPF86 XPF88 XPF103 XPF104 XPF106 XPF108 XPF1010 XPF123 XPF124 XPF126 XPF128 XPF1210 XPF1212 XPFA4 XPFA6 XPFA8 XPFA10 XPFA12 XPK3 XPK4 XPK6 XPK8 XPTK3 XPTK4 XPTK6 XPTK8 XPP3 XPP4 XPP6 XPP8 XPTP3 XPTP4
45 Elbow
2212 Elbow
1114 Elbow
Tee
Cap
Tapped Cap
Plug
Tapped Plug
3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 4 63 64 6 83 84 86 8 103 104 106 108 10 123 124 126 128 1210 12 44 63 64 66 83 84 86 88 103 104 106 108 1010 123 124 126 128 1210 1212 4 6 8 10 12 3 4 6 8 3 4 6 8 3 4 6 8 3 4
350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350
(2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415) (2415)
FM Approvals
1-473
Product Designation
Fitting Description
XPTP6 XPTP8
6 8
Series 3000 StarGrip All Grip MJG StarFlange Model 3200 RAC
Mechanical Joint Restrainer Gland Mechanical Joint Restrainer Gland Mechanical Joint Restrainer Gland Restrained Adapter Flange Restrained Flange Adapter Fitting
175 (1205) 175 (1205) 350 (2415) 175 (1205) 175 (1205)
a a a b
Remarks: a. Used to join plain ended ductile iron pipe to mechanical joint ended devices in underground mains or at the base only of a sprinkler riser. b. Used to join plain ended ductile iron pipe to flange ended devices in underground mains or at the base only of a sprinkler riser. Fitting Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)(psi)
Blind Flange 90 Elbow Flanged 90 Base Elbow, Flanged 90 Long Radius Elbow, Flanged 90 Reducing Elbow, Flanged 2,
3, 4, 6, 8 ,10, 12 3, 4, 6, 8, 10, 12 3x212, 43, 63, 64, 84, 86, 104, 106, 108, 126, 128, 1210 2, 212, 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 2, 212, 3, 4, 5, 6, 8, 10, 12
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Equal Tee, Flanged Base Equal Tee, Flanged Reducing Branch Tee, Flanged
3, 4, 6, 8, 10, 12 3x2, 42, 4x3, 6x2, 63, 64, 83, 84, 86 104, 106, 108, 124, 126, 128, 1210 646, 868 668, 8810, 101012 6x4x4, 121010 3, 4, 6, 8, 10, 12 43, 63, 64, 83, 84, 86, 104, 106, 108, 124, 126, 128, 1210 43, 63, 64, 84, 86, 104, 106, 108, 124, 126, 128, 1210 43, 63, 64, 84, 86, 104, 106, 108 126, 128, 1210 3, 4, 6, 8, 10, 12
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
Reducing Run Tee, Flanged Bullhead Tee, Flanged Reducing Run, Reducing Branch Tee, Flanged Equal Cross, Flanged Reducing Cross, Flanged
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070)
300 (2070)
300 (2070)
300 (2070)
FM Approvals
1-474
Fitting Description
45 Elbow, Compact, Flanged Equal Tee, Compact, Flanged Reducing Tee, Compact, Flanged Equal Cross, Compact, Flanged Concentric Reducer, Compact, Flanged AC9 Coupling AC9 Coupling AE1C 90 Elbow AE1C 90 Elbow AE2C 45 Elbow AE2C 45 Elbow AK1C End Cap AK1C End Cap AT1C Equal Tee AT1C Equal Tee AT2C Reducing Branch Tee AT2C Reducing Branch Tee AR1C Concentric Reducer AR1C Concentric Reducer AR2C Eccentric Reducer AR2C Eccentric Reducer
4, 6, 8, 10, 12 4, 6, 8, 10, 12 43, 64, 84, 86, 106, 108, 126, 128, 8 64, 86, 3, 4, 6, 8 10, 12 3, 4, 6, 8 10, 12 3, 4, 6, 8 10, 12 3, 4, 6, 8 10, 12 3, 4, 6, 8 10, 12 664, 886 10108, 121210 43, 64, 86 108, 1210 43, 64, 86 108, 1210
300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 250 (1750) 250 (1750) 175 (1205) 250 (1750) 175 (1205) 250 (1750) 175 (1205) 250 (1750) 175 (1205) 250 (1750) 175 (1205) 250 (1750) 175 (1205) 250 (1750) 175 (1205)
Pipe with VRS-TIROFLEX spigot-and-socket joint with and without welded bead Pipe section with two welded beads Flanged sockets (EU) Flanged spigots (F) VRS joint 90 double-socket bend (MMQ) 45 double-socket bend (MMK) 30 double-socket bend (MMK) 2212 double-socket bend (MMK)
80 through 300
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
80 through 300 80 through 300 80 through 300 80 through 300 80 through 300 250250100, 150, 200, 250 200200100, 150, 200 150150100, 150 125125100, 125 100100100 300300100, 150, 200, 250, 300 250250100, 150, 200, 250 200200100, 150, 200
1114 double-socket bend (MMK) Double-socket tee with flanged branch (MMA) Double-socket tee with flanged branch (MMA) Double-socket tee with flanged branch (MMA) Double-socket tee with flanged branch (MMA) Double-socket tee with flanged branch (MMA) All socket Tee (MMB) All socket Tee (MMB) All socket Tee (MMB)
FM Approvals
1-475
Description
All socket Tee (MMB) All socket Tee (MMB) All socket Tee (MMB) Double-socket taper (MMR) Double-socket taper (MMR) Double-socket taper (MMR) Double-socket taper (MMR) Double-socket taper (MMR) 90 flanged bend (Q) 45 flanged bend (FFK) 30 flanged bend (FFK) 2212 flanged bend (FFK)
150150100, 150 125125100, 125 100100100 300150, 200, 250 250125, 150, 200 200100, 125, 150 150100, 125 125100 80 through 300 80 through 300 80 through 300 80 through 300 80 through 300 80 through 300 300300100, 200, 300 250250100, 200, 250 200200100, 150, 200 150150100, 125, 150 125125100, 125 100100100 250200 200100, 125, 150 150100, 125 125100 80 through 300 80 through 300 80 through 300
1114 flanged bend (FFK) 90 double-flanged duckfoot bend (N and QN) All flanged tee All flanged tee All flanged tee All flanged tee All flanged tee All flanged tee Double-flanged taper (FFR) Double-flanged taper (FFR) Double-flanged taper (FFR) Double-flanged taper (FFR) Blank flange (X): DN 50-250 Blank flange (X): DN 300-500 Plug (P)
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 16 (230) 10.5 (150) 16 (230)
Tyler Pipe Co, Div of McWane Inc, Box 2027, Tyler Texas 75710-2027
Ductile iron restraint gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended pipe, fittings or other components.
Nominal Pipe Size, in. Rated Working Pressure psi (kPa)
Description
TSLD TSLD
4, 6, 8, 10, 12 16
90 Elbow (M.J.)
3 4
45 Elbow (M.J.)
6 8 10 12
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070)
FM Approvals
1-476
Product Designation
Fitting Description
TDMB1490 TDMB1690 TDMB345 TDMB445 TDMB645 TDMB845 TDMB1045 TDMB1245 TDMB1445 TDMB1645 TDMB322 TDMB422 TDMB622 TDMB822 TDMB1022 TDMB1222 TDMB1422 TDMB1622 TDMB311 TDMB411 TDMB611 TDMB811 TDMB1011 TDMB1211 TDMB1411 TDMB1611 TDMR43 TDMR63 TDMR64 TDMR84 TDMR86 TDMR104 TDMR106 TDMR108 TDMR124 TDMR126 TDMR128 TDMR1210 TDMR1410 TDMR166 TDMR168 TDMR1610 Reducer 1114 Elbow 2212 Elbow (M.J.)
14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 43 63 64 84 86 104 106 108 124 126 128 1210 1410 166 168 1610
300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 250 (1725) 250 (1725) 350 (2415)
FM Approvals
1-477
Product Designation
Fitting Description
TDMR1612 TDMR1614 TDMK3 TDMK4 TDMK6 TDMK8 TDMK10 TDMK12 TDMK14 TDMK16 TDMP3 TDMP4 TDMP6 TDMP8 TDMP10 TDMP12 TDMP14 TDMP16 TDTK3 TDTK4 TDTK6 TDTK8 TDTK10 TDTK12 TDTK16 TDTP3 TDTP4 TDTP6 TDTP8 TDTP10 TDTP12 TDTP16 TDMS3 TDMS4 TDMS6 TDMS8 TDMS10 TDMS12 TDMS14 TDMS16 TDML3 TDML4 Long Sleeve (M.J.) Short Sleeve (M.J.) Tapped Plug (M.J.) Tapped Cap (M.J.) Solid Plug (M.J.) Solid Cap (M.J.)
1612 1614 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 16 3 4 6 8 10 12 16 3 4 6 8 10 12 14 16 3 4
250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 250 (1725) 350 (2415) 350 (2415)
FM Approvals
1-478
Product Designation
Fitting Description
TDML6 TDML8 TDML10 TDML12 TDML16 TDG3 TDG4 TDG6 TDG8 TDG10 TDG12 TDG16 TDMC43 TDMC44 TDMC64 TDMC66 TDMC84 TDMC86 TDMC88 TDMC104 TDMC106 TDMC108 TDMC1010 TDMC124 TDMC126 TDMC128 TDMC1210 TDMC1212 TDMO612 TDMO126 TDMH66 TDMH86 TDMH88 TDMH106 TDMH108 TDMH126 TDMH128 TDMH146 TDMH166 TDMF44 TDMF64 Hydrant Tee (M.J. M.J. Flanged End) Hydrant Tee (M.J. M.J. Swivel End) Offset Cross (M.J.) M.J. Gland Long Sleeve (M.J.)
6 8 10 12 16 3 4 6 8 10 12 16 43 44 64 66 84 86 88 104 106 108 1010 124 126 128 1210 1212 612 126 66 86 8x8 106 10x8 126 128 146 166 44 6x4
350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415)
FM Approvals
1-479
Product Designation
Fitting Description
TDMF66 TDMF84 TDMF86 TDMF88 TDMF104 TDMF106 TDMF108 TDMF1010 TDMF124 TDMF126 TDMT33 TDMT43 TDMT44 TDMT63 TDMT64 TDMT66 TDMT84 TDMT86 TDMT88 TDMT104 TDMT106 TDMT108 TDMT1010 TDMT124 TDMT126 TDMT128 TDMT1210 TDMT1212 TDMT143 TDMT144 TDMT146 TDMT148 TDMT1410 TDMT1412 TDMT166 TDMT168 TDMT1610 TDMT1612 TDMT1614 TDMT1616 TRMG3 TRMG4 Retainer Gland Heavy Duty (M.J.) Hydrant Tee (M.J.)
66 8x4 86 88 10x4 106 10x8 10x10 12x4 126 33 43 44 63 64 66 84 86 88 104 106 108 1010 124 126 128 1210 1212 143 144 146 148 1410 1412 166 168 1610 1612 1614 1616 3 4
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 250 (1725)
FM Approvals
1-480
Product Designation
Fitting Description
TRMG6 TRMG8 TRMG10 TRMG12 TRLG6 TRLG8 TDMY33 TDMY43 TDMY44 TDMY63 TDMY64 TDMY66 TDMY83 TDMY84 TDMY86 TDMY88 TDMY103 TDMY104 TDMY106 TDMY108 TDMY1010 TLPR43 TLPR63 TLPR64 TLPR84 TLPR86 TLPR104 TLPR106 TLPR108 TLPR124 TLPR126 TLPR128 TLPR1210 TLPR166 TLPR168 TLPR1612 TSPR43 TSPR63 TSPR64 TSPR84 TSPR86 TSPR104 Reducer (P.E. M.J.) Reducer (M.J. P.E.) 45 Wye Retainer Gland Standard (M.J.)
6 8 10 12 6 8 3 43 4 63 64 6 83 84 86 88 103 104 106 108 1010 43 6x3 64 84 86 104 106 108 124 126 128 1210 166 168 1612 43 6x3 64 84 86 104
300 (2070) 250 (1725) 175 (1205) 175 (1205) 300 (2070) 175 (1205) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-481
Product Designation
Fitting Description
TSPR106 TSPR108 TSPR124 TSPR126 TSPR128 TSPR1210 TSPR166 TSPR168 TSPR1612 TPPR43 TPPR64 TPPR84 TPPR86 TPPR104 TPPR106 TPPR108 TPPR124 TPPR126 TPPR128 TPPR1210 TPPR166 TPPR168 TPPR1612 TMFA3 TMFA4 TMFA6 TMFA8 TMFA10 TMFA12 TDTT3 TDTT4 TDTT6 TDTT8 TDTT10 TDTT12 TDTT16 TDTC4 TDTC6 TDTC8 TDTC10 TDTC12 TDTC16 Tapped Cross Tapped Tees Adapter Flanged End M.J. Reducer Plain Ends
106 108 124 126 128 1210 166 168 1612 43 64 84 86 104 106 108 124 126 128 1210 166 168 1612 3 4 6 8 10 12 3 4 6 8 10 12 16 4 6 8 10 12 16
350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 300 (2070) 300 (2070) 300 (2070) 250 (1725) 250 (1725) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 300 (2070) 250 (1725)
FM Approvals
1-482
Product Designation
Fitting Description
TDFB390 TDFB490 TDFB690 TDFB890 TDFB1090 TDFB1290 TDFB345 TDFB445 TDFB645 TDFB845 TDFB1045 TDFB1245 TDFB322 TDFB422 TDFB622 TDFB822 TDFB1022 TDFB1222 TDFB311 TDFB411 TDFB611 TDFB811 TDFB1011 TDFB1211 TDFB32 TDFB43 TDFB63 TDFB64 TDFB65 TDFB84 TDFB85 TDFB86 TDFB104 TDFB106 TDFB108 TDFB124 TDFB126 TDFB128 TDFB1210 TDFL390 TDFL490 TDFL690 TDFL890 TDFL1090 TDFL1290 TDFD3 TDFD4 TDFD6 TDFD8 TDFD10 TDFD12 TDFT33 TDFT44 TDFT55 TDFT66 TDFT88 TDFT1010 TDFT1212 TDFT32 TDFT42 TDFT425 TDFT43 TDFT62 TDFT63 TDFT64 TDFT84 TDFT86 TDFT104 TDFT106 TDFT108 TDFT124 TDFT126 TDFT128 TDFT1210
90 Elbow (Flanged)
3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 32 43 63 64 65 84 85 86 104 106 108 124 126 128 1210 3 4 6 8 10 12 3 4 6 8 10 12 3 4 5 6 8 10 12 32 42 4212 43 62 63 64 84 86 104 106 108 124 126 128 1210
250 (1750)
45 Elbow (Flanged)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-483
Product Designation
Fitting Description
TDRT433 TDRT533 TDRT544 TDRT633 TDRT644 TDRT646 TDRT864 TDRT866 TDRT868 TDFC33 TDFC44 TDFC55 TDFC66 TDFC88 TDFC1010 TDFC1212 TDFC32 TDFC42 TDFC425 TDFC43 TDFC62 TDFC63 TDFC64 TDFC84 TDFC86 TDFC104 TDFC106 TDFC108 TDFC124 TDFC126 TDFC128 TDFC1210 TDFR32 TDFR325 TDFR42 TDFR425 TDFR43 TDFR62 TDFR625 TDFR63 TDFR64 TDFR65 TDFR84 TDFR85 TDFR86 TDFR104 TDFR106 TDFR108 TDFR124 TDFR126 TDFR128 TDFR1210 TDFE32 TDFE325 TDFE42 TDFE425 TDFE43 TDFE62 TDFE625 TDFE63 TDFE64 TDFE84 TDFE85 TDFE86 TDFE104 TDFE106 TDFE108 TDFE124 TDFE126 TDFE128 TDFE1210 TDTF3 TDTF4 TDTF6 TDTF8
433 533 544 644 644 646 864 866 868 3 4 5 6 8 10 12 32 42 4212 43 62 63 64 84 86 104 106 108 124 126 128 1210 32 3212 42 4212 43 62 6212 63 64 65 84 85 86 104 106 108 124 126 128 1210 32 3212 42 4212 43 62 6212 63 64 84 85 86 104 106 108 124 126 128 1210 3 4 6 8
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
250 (1750)
FM Approvals
1-484
Product Designation
Fitting Description
10 12 3 4 6 8 10 12
250 (1750)
250 (1750)
Tll above products used to join plain-end or mechanical joint or flanged ductile iron pipe to mechanical joint or flanged or plain end devices as noted or to identical adapters in underground mains. Full Body Mechanical Joint Pipe Fittings.
Product Designation Fitting Description Nominal Pipe Size, in. Max Rated Pressure, psi (kPa)
TXMB390 TXMB490 TXMB690 TXMB890 TXMB1090 TXMB1290 TXMB345 TXMB445 TXMB645 TXMB845 TXMB1045 TXMB1245 TXMB322 TXMB422 TXMB622 TXMB822 TXMB1022 TXMB1222 TXMB311 TXMB411 TXMB611 TXMB811 TXMB1011 TXMB1211 TXME390 TXME490 TXME690 TXME890 TXME1090 TXME1290 TXME345 TXME445 TXME645
90 Elbow
3 4 6 8 10 12
45 Elbow
3 4 6 8 10 12
2212 Elbow
3 4 6 8 10 12
1114
Elbow
3 4 6 8 10 12
3 4 6 8 10 12
3 4 6
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-485
Product Designation
Fitting Description
TXME845 TXME1045 TXME1245 TXME322 TXME422 TXME622 TXME822 TXME1022 TXME1222 TXME311 TXME411 TXME611 TXME811 TXME1011 TXME1211 TXMT43 TXMT44 TXMT63 TXMT64 TXMT66 TXMT83 TXMT84 TXMT86 TXMT88 TXMT103 TXMT104 TXMT106 TXMT108 TXMT1010 TXMT123 TXMT124 TXMT126 TXMT128 TXMT1210 TXMT1212 TXMT143 TXMT144 TXMT146 TXMT148 TXMT1410 TXMT1412 TXMT1414 Tee (M.J.) Plain End 1114 Elbow (M.J.) Plain End 2212 Elbow
8 10 12 3 4 6 8 10 12 3 4 6 8 10 12 43 4 63 64 6 83 84 86 8 103 104 106 108 10 123 124 126 128 1210 12 143 144 146 148 1410 1412 14
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-486
Product Designation
Fitting Description
TXMT163 TXMT164 TXMT166 TXMT168 TXMT1610 TXMT1612 TXMT1614 TXMT1616 TXMC33 TXMC43 TXMC44 TXMC63 TXMC64 TXMC66 TXMC84 TXMC86 TXMC88 TXMC104 TXMC106 TXMC108 TXMC1010 TXMC124 TXMC126 TXMC128 TXMC1210 TXMC1212 TXMH64 TXMH66 TXMH84 TXMH86 TXMH88 TXMH104 TXMH106 TXMH108 TXMH1010 TXMH124 TXMH126 TXMH128 TXMH1210 TXMH1212 TXMF44 TXMF64 Tee (M.J. M.J. Flanged End) Hydrant Tee (M.J. M.J. Swivel End) Cross (M.J. M.J.)
163 164 166 168 1610 1612 1614 16 3x3 43 4x4 63 64 66 84 86 8x8 104 106 108 10x10 124 126 128 1210 12x12 6x4 6x6 8x4 8x6 8x8 10x4 10x6 10x8 10x10 12x4 12x6 12x8 12x10 12x12 4x4 6x4
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-487
Product Designation
Fitting Description
TXMF66 TXMF84 TXMF86 TXMF88 TXMF104 TXMF106 TXMF108 TXMF1010 TXMF124 TXMF126 TXMF128 TXMF1210 TXMF1212 TXMR43 TXMR63 TXMR64 TXMR84 TXMR86 TXMR104 TXMR106 TXMR108 TXMR124 TXMR126 TXMR128 TXMR1210 TXSPR43 TXSPR63 TXSPR64 TXSPR84 TXSPR86 TXSPR104 TXSPR106 TXSPR108 TXSPR124 TXSPR126 TXSPR128 TXSPR1210 TXLPR43 TXLPR63 TXLPR64 TXLPR84 TXLPR86 Reducer (M.J. P.E.) Reducer (P.E. M.J.) Reducer (M.J. M.J.)
6x6 8x4 8x6 8x8 10x4 10x6 10x8 10x10 12x4 12x6 12x8 12x10 12x12 43 63 64 84 86 104 106 108 124 126 128 1210 4x3 6x3 6x4 8x4 8x6 10x4 10x6 10x8 12x4 12x6 12x8 12x10 4x3 6x3 6x4 8x4 8x6
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-488
Product Designation
Fitting Description
TXLPR104 TXLPR106 TXLPR108 TXLPR124 TXLPR126 TXLPR128 TXLPR1210 TXMFT6 TXMFA8 TXMFA10 TXMFA12 TXMS3 TXMS4 TXMS6 TXMS8 TXMS10 TXMS12 TXMS14 TXMS16 TXML3 TXML4 TXML6 TXML8 TXML10 TXML12 TXML14 TXML16 TXMK3 TXMK4 TXMK6 TXMK8 TXMK10 TXMK12 TXMK14 TXMK16 TXTK3 TXTK4 TXTK6 TXTK8 TXTK10 TXTK12 TXTK14 Tapped Cap Cap Long Sleeve (M.J. M.J.) Short Sleeve (M.J. M.J.) Flange Adapter ( M.J. Flange)
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-489
Product Designation
Fitting Description
TXTK16 TXMP3 TXMP4 TXMP6 TXMP8 TXMP10 TXMP12 TXMP14 TXMP16 TXTP3 TXTP4 TXTP6 TXTP8 TXTP10 TXTP12 TXTP14 TXTP16 Tapped Plug Plug
16 3 4 6 8 10 12 14 16 3 4 6 8 10 12 14 16
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
TDPB390 TDPB490 TDPB690 TDPB890 TDPB1090 TDPB345 TDPB445 TDPB645 TDPB845 TDPB1045 TDPB322 TDPB422 TDPB622 TDPB822 TDPB1022 TDPB311 TDPB411 TDPB611 TDPB811 TDPB1011 TDPF44 TDPF64
90 Elbow
3 4 6 8 10
45 Elbow
3 4 6 8 10
2212 Elbow
3 4 6 8 10
1114
Elbow
3 4 6 8 10
Tee (Push-OnFlange)
4x4 6x4
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-490
Product Designation
Fitting Description
TDPF66 TDPF86 TDPF88 TDPF103 TDPF106 TDPF108 TDPF126 TDPF128 TDPY 44 TDPY 63 TDPY 64 TDPY 66 TPFA6 TPFA8 TPFA10 TPFA12 TPR84 Reducer (Push-On Push-On) Flange Adapter (Push-On Flange) 45 Wye
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
TXPB390 TXPB490 TXPB690 TXPB890 TXPB1090 TXPB1290 TXPB345 TXPB445 TXPB645 TXPB845 TXPB1045 TXPB1245 TXPB322 TXPB422 TXPB622 TXPB822 TXPB1022 TXPB1222 TXPB311 TXPB411 TXPB611 TXPB811
90 Elbow
3 4 6 8 10 12
45 Elbow
3 4 6 8 10 12
2212
Elbow
3 4 6 8 10 12
1114 Elbow
3 4 6 8
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-491
Product Designation
Fitting Description
TXPB1011 TXPB1211 TXPT44 TXPT63 TXPT64 TXPT66 TXPT83 TXPT84 TXPT86 TXPT88 TXPT103 TXPT104 TXPT106 TXPT108 TXPT1010 TXPT123 TXPT124 TXPT126 TXPT128 TXPT1210 TXPT1212 TXPF44 TXPF63 TXPF64 TXPF66 TXPF83 TXPF84 TXPF86 TXPF88 TXPF103 TXPF104 TXPF106 TXPF108 TXPF1010 TXPF123 TXPF124 TXPF126 TXPF128 TXPF1210 TXPF1212 TXPFA4 TXPFA6 Flange Adapter( Push-On Flange) Tee (Push-On Flange) Tee
10 12 4 63 64 6 83 84 86 8 103 104 106 108 10 123 124 126 128 1210 12 4x4 6x3 6x4 6x6 8x3 8x4 8x6 8x8 10x3 10x4 10x6 10x8 10x10 12x3 12x4 12x6 12x8 12x10 12x12 4 6
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
FM Approvals
1-492
Product Designation
Fitting Description
TXPFA8 TXPFA10 TXPFA12 TXPK3 TXPK4 TXPK6 TXPK8 TXPTK3 TXPTK4 TXPTK6 TXPTK8 TXPP3 TXPP4 TXPP6 TXPP8 TXPTP3 TXPTP4 TXPTP6 TXPTP8 Tapped Plug Plug Tapped Cap Cap
8 10 12 3 4 6 8 3 4 6 8 3 4 6 8 3 4 6 8
350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415) 350 (2415)
Uni-Flange, Sub Ford Meter Box Co Inc, Box 443, Wabash IN 46992
Ductile iron flange adapters used to join plain-end ductile iron pipe to flanged devices in underground mains or at the first aboveground connection at the base of the sprinkler riser, only*. Mechanical Joint Retainer Gland. Series 1400. 4, 6, 8, 10 and 12 in. For use with ductile iron pipe.
Union Foundry Co, 1501 W 17th St, Box 309, Anniston AL 36208
Product Description Fitting Description Nominal Pipe Size, in.
3* 4* 6* 8** 10 12
Flange Adapters used to join plain-end ductile iron pipe to flanged devices in underground mains or at the first aboveground connection at the base of a sprinkler riser, only. Nominal 90 lbft (120 nm) torque set screws supplied with flange adapter.
*300 psi (2070 kPa) rated working pressure. **200 psi (1380 kPa) rated working pressure. 175 psi (1205 kPa) rated working pressure.
United States Pipe & Foundry Co, 3300 First Ave N, Birmingham AL 35222
Tyton Joint Pipe and Fittings. Pressure rating 350 psi (2415 kPa). When used with Field-Lok gasket as a joint restraint the pressure rating is 200 psi (1380 kPa). When used with the Field Lok 350 gasket and joint restraint, the pressure rating is 250 psi (1725 kPa), except for the 18, 20 and 24 in. NPS, which is rated at 200 psi (1379 kPa).
Product Description Nominal Pipe Size, in. Remarks
Pipe Pipe 90 Elbow 45 Elbow 2212 Elbow 1114 Elbow Connecting Piece Connecting Piece Tee
4 through 16 18, 20 and 24 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12 444 664
Classes 50 through 56* 200 psi rated working pressure BB BB BB BB TJTJ TJFlg BBB
FM Approvals
1-493
Product Description
Remarks
Cross
Concentric Reducer
666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 4444 6644 6666 8844 8866 8888 101044 101066 101088 10101010 121244 121266 121288 12121010 12121212 64 84 86 104 106 108 124 126 128 1210 4 through 12 666 886 10106 12126 16166
BBBB
Small end B
BBS
Trim Tyton Fittings. Pressure rating 350 psi (2415 kPa). When used with Field-Lok gasket as a joint restraint the pressure rating is 200 psi (1380 kPa).
90 Elbow 45 Elbow 2212 Elbow 1114 Elbow Tee 4 4 4 4 through 12 through 12 through 12 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 64 84 86 104 106 108 124 126 BB BB BB BB BBB
Concentric Reducer
Small End B
FM Approvals
1-494
Product Description
Remarks
Hydrant Tee
BBS
Reducer
BB
BB
BBS
TR-FLEX Restrained Joint, Pipe and Fittings. Pressure rating 250 psi (1725 kPa). When used with Gripper Ring as a joint restraint the pressure rating is 200 psi (1380 kPa).
Pipe 90 Elbow 45 Elbow 2212 Elbow 1114 Elbow Tee 4 4 4 4 4 through 12 through 12 through 12 through 12 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 4444 6644 6666 8844 8866 8888 Classes 50 through 56* BB BB BB BB BBB
Cross
BBBB
FM Approvals
1-495
Product Description
Remarks
Concentric Reducer
101044 101066 101088 10101010 121244 121266 121288 12121010 12121212 64 84 86 104 106 108 124 126 128 1210 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12
BB
Mechanical Joint Pipe and Fittings. Pressure rating 350 psi (2415 kPa).
Pipe 90 Elbow 45 Elbow 2212 Elbow 1114 Elbow 90 Base Elbow Tee through 12 through 12 through 12 through 12 through 12 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 444 666 888 101010 121212 4444 6644 6666 8844 8866 8888 101044 101066 101088 10101010 121244 121266 121288 12121010 12121212 64 84 86 104 4 4 4 4 4 4 Classes 50-56* BB, BS BB, BS BB, BS BB, BS BB, BS BBB
Base Tee
BBB
Cross
BBBB
Reducer
MJMJ
FM Approvals
1-496
Product Description
Remarks
Reducer
Reducer
Offset
Solid Sleeve
Connecting Piece Connecting Piece Connecting Piece Connecting Piece Cap Plug Dual Purpose Solid Sleeve Wye Branch
106 108 124 126 128 1210 64 84 86 104 106 108 124 126 64 128 1210 64 84 86 104 106 108 124 126 128 1210 46 Offset27 Long 412 Offset30 Long 66 Offset28 Long 612 Offset34 Long 618 Offset41 Long 86 Offset29 Long 812 Offset36 Long 818 Offset43 Long 106 Offset30 Long 1012 Offset38 Long 1018 Offset46 Long 126 Offset34 Long 1212 Offset45 Long 1218 Offset56 Long 4 through 12712 Long 4 through 1212 Long 4 through 1210 Long Min 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12 4 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 666 886 10106 12126 16166 888 10108 12128 613 Long 624 Long 636 Long
BS
BB
BB BBB
BBS
SS
FM Approvals
1-497
Product Description
Remarks
FLANGED Pipe and Fittings. Pressure rating 250 psi (2415 kPa).
Pipe 90 Elbow 90 Long Radius Elbow 45 Elbow 2212 Elbow 1114 Elbow 90 Base Elbow Tee through 12 through 12 through 12 through 12 through 12 through 12 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 121212 444 666 888 101010 121212 4444 6644 6666 8844 8866 8888 101044 101066 101088 10101010 121244 121266 121288 12121010 12121212 64 84 86 104 106 108 124 126 128 1210 4 through 12 4 through 12 444 664 666 884 886 888 10104 10106 10108 101010 12124 12126 12128 121210 4 4 4 4 4 4 4 Classes 53 through 56* Flg, Flg Flg, Flg Flg, Flg Flg, Flg Flg, Flg Flg, Flg Flg, Flg, Flg
Base Tee
Cross
Reducer
Flg, Flg
FM Approvals
1-498
Product Description
Remarks
True Wye Side Outlet 90 Elbow Side Outlet Tee Straight 90 Elbow 90 Long Radius Elbow Return Bend
*Min thickness in 4 in. size is Class 51.
4 4 4 4 4 4 4
Flg, Flg, Flg Flg, Flg, Flg Flg, Flg, Flg, Flg Flg and Flare Flg and Flare Flg and Flare Flg, Flg
B-Bell End, S-Spigot End, TJ-Tyton Joint, MJ-Mechanical Joint, TRF-TR-Flex Joint, Flg-Flanged End, PE-Plain End. MJ Field Lok Retainer Gland for ductile iron pipe. Used to secure spigot ends of ductile iron pipe into standardized mechanical joint-ended fitting or other components.
Product Description Nominal Pipe Size, in. Rated Working Pressure, psi (kPa)
MJ Field Lok
4, 6, 8, 10, 12
175 (1205)
CI CI CI CI CI CI
90 Elbow 90 Long Radius Elbow 45 Elbow 2212 Elbow 1114 Elbow Reducing Elbow
CI CI
CI CI CI
Cap 90 Elbow 45 Elbow Tee Products listed below are rated at 250 psi (1725 kPa) 90 Elbow 45 Elbow Tee Cap
4, 6, 8, 10, 12, 14, 16 4, 6, 8, 10, 12 4, 6, 8, 10, 12, 14, 16 4, 6, 8, 10, 12 4, 6, 8, 10, 12 43; 63, 4; 84, 6; 106, 8 4, 6, 8, 10, 12 43; 64; 84, 6; 104, 6, 8; 124, 6, 8, 10 4, 6, 8, 10, 12 4, 6, 8, 10, 12 43; 64; 84, 6; 104, 6, 8; 124, 6, 8, 10 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12
16 16 16 16
Style 341 Vic-Flange. For use with cut groove-ended cast iron or ductile iron pipe in underground installations. With Grade H or M gasket material.
341 Vic-Flange 4, 6, 8, 10, 12
Style 342 Vic-Flange. For use with cut groove-ended ductile iron pipe in underground installations. With Grade H or M gasket material.
342 Vic-Flange 14, 16
FM Approvals
1-499
Product Designation
307 31
Rolled Groove, Cut Groove (a, d) Cut Groove (a, b) Cut Groove (a, c)
a. b. c. d.
With gasket M. Joins Cast Iron or Ductile Iron Pipe and fittings in underground main installations. Joins Ductile Iron Pipe and fittings in underground main installations. Joins rolled or cut grooved steel pipe to Ductile Iron pipe.
Style 341 Vic-Flange. For use with cut groove-ended cast iron or ductile iron pipe in underground installations. With Grade H or M gasket material. 341 Vic-Flange 4, 6, 8, 10, 12
Style 342 Vic-Flange. For use with cut groove-ended ductile iron pipe in underground installations. With Grade H or M gasket material. 342 Vic-Flange 14, 16
Product Description
Fitting Description
CI CI CI CI CI
4, 6, 8, 10, 12, 14, 16 4, 6, 8, 10, 12 4, 6, 8, 10, 12, 14, 16 4, 6, 8, 10, 12 4, 6, 8, 10, 12 43; 63, 4; 84, 6; 106, 8 4, 6, 8, 10, 12 43; 64; 84, 6; 104, 6, 8; 124, 6, 8, 10
CI
Reducing Elbow
CI
Tee
CI
Reducing Tee
CI CI
Lateral Cross
4, 6, 8, 10, 12 4, 6, 8, 10, 12 43; 64; 84, 6; 104, 6, 8; 124, 6, 8, 10 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12
CI
Reducer
Cap 90 Elbow 45 Elbow Tee Products Listed Below are rated at 250 psi (1725 kPa)
FM Approvals
1-500
Blind Flange 90 Elbow, Flanged 90 Base Elbow, Flanged 90 Long Radius Elbow, Flanged 90 Reducing Elbow, Flanged
3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8 ,10, 12 3, 4, 6, 8 43, 63, 64, 84, 86 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 3, 4, 6, 8, 10, 12 443, 663, 664 884, 886, 10104, 10106, 10108, 12124, 12126, 12128, 121210 3, 4, 6, 8, 10, 12 43, 63, 64, 83, 84, 86, 104, 106, 108, 124, 126, 128, 1210 43, 63, 64, 84, 86, 104, 106, 108, 124, 126, 128, 1210 43, 63, 64, 84, 86, 104, 106, 108
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
Equal Tee, Flanged Base Equal Tee, Flanged Reducing Branch Tee, Flanged
175 (1205)
175 (1205)
FM Approvals
1-501
W193-001 W193-002 W193-003 W193-004 W193-005 W193-006 W193-007 W193-008 W193-009 W193-010 W193-011 W193-012 W193-013 W193-014 W193-015 W193-016 W193-017 W193-018 W193-019 W193-020 W193-021 W193-022 W193-023 W193-024 W193-025 W193-026 W193-027 W193-028 W193-029 W193-030 W193-031 W193-067 W193-068 W193-069 W193-070 W193-052 W193-053 W193-054 W193-055 W193-056 W193-037 W193-038 W193-039 W193-040 W193-041 W193-057 W193-058 W193-059 W193-060 W193-061 W193-062 W193-063 W193-064 W193-065 W193-066 W193-042 W193-043 W193-044 W193-045 W193-046 W193-047 W193-048 W193-049
1114 Elbow
2212 Elbow
45 Elbow
90 Elbow
Tee
Reducing Tee
Cross
End Cap
Reducing Cross
Reducer
4 6 8 10 12 4 6 8 10 12 4 6 8 10 12 4 6 8 10 12 4 6 8 10 12 664 884 886 10104 10106 10108 12124 12126 12128 121210 4444 6666 8888 10101010 12121212 4 6 8 10 12 6644 8844 8866 101044 101066 101088 121244 121266 121288 12121010 64 84 86 104 106 108 124 126
FM Approvals
1-502
Product Designation
Fitting Description
FlangeGasket Adapter
128 1210 4 6 8 10 12
Clow Canada, Div Canada Pipe Co Ltd, 245 Industrial Dr, Grandview Industrial Park, Saint John New Brunswick E2R 1A4 Canada
Ductile iron restrainers for AWWA C-900 PVC pipe. Used to secure spigot ends of PVC pipe into standardized mechanical joint ended pipe fitting or other components.
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Series 300C
4, 6, 8, 10 12
a b
a. For use with Class 150 or Class 200 cast iron pipe equivalent sized PVC pipe. b. For use with Class 150 cast iron pipe equivalent sized PVC pipe.
4, 6, 8, 10, 12
a, b
4, 6, 8, 10, 12
a, b
a. Pipe lengths are joined by single-gasketed bell and spigot joints and are joined to cast iron fittings. b. Forsheda and S&B Technical Products gaskets available.
4 6 8 10 12
200 (1380) 200 (1380) 200 (1380) 200 (1380) 150 (1035)
a a a a b
Series 2100 2104 2106 2108 2110 2112 a. For use with AWWA C900 PC200 pipe. b. For use with AWWA C900 PC150 pipe.
4 6 8 10 12
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
a a a a a
Freedom Plastics Inc, 215 South Arch St, Box 1488, Janesville WI 54548
Pure-Blue AWWA C900 Pipe DR18 PC 150 Pure-Blue AWWA C900 Pipe DR14 PC 200 Pure-Blue AWWA C905 Pipe DR25 PC 165 Pure-Blue AWWA C905 Pipe DR18 PR 235 4, 6, 8, 10, 12 150 (1035) 200 (1380) 165 (1140) 235 (1620) a, b
6, 8, 10, 12
a, b
16
a, b
16
a, b
FM Approvals
1-503
Product Designation
Remarks
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron pipe fittings having standardized mechanical joint connections. b. Pipes are FM Approved when supplied with the Rieber style gaskets.
Industrias Vassallo Inc, Box 473, Coto Laurel, Puerto Rico 00644
AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200
4, 6, 8, 10, 12
a, b, c
4, 6, 8, 10, 12
a, b, c
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron fittings having standardized mechanical joint connections. b. Pipes are Approved when supplied with either Vassallo or Rieber style gaskets. c. Pipes are considered Approved when supplied in either light blue or white in color.
IPEX Inc, 3 Place du Commerce, Suite 101, Ile-des-Soeurs Verdun, Quebec H3E 1H7, Canada
Blue Brute Pipe AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200
4, 6, 8, 10, 12
4, 6, 8, 10, 12
Big Brute/Centurion AWWA C905 Pipe DR18 PR 235 AWWA C905 Pipe DR14 PR 310
16
Transition Fittings (IPS CI Adapters) Blue Brute Fittings Stop Couplings Repair Couplings
b, d, e
4, 6, 8, 10 4, 6, 8, 10 10
Reducing Bushings
64 86 10 8 12 10
4, 6, 8, 10 4
34
AWWA
4 1 AWWA 6 34 AWWA
150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035)
c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d
FM Approvals
1-504
Product Designation
Remarks
150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035)
c, d c, d c, d c, d c, d c, d c, d
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron fittings having bell or standardized mechanical joint connections. b. For use with Class 150 and 200 pipe. c. For use with Class 150 pipe. d. For use with cast iron pipe equivalent sized PVC pipe. e. For use with steel pipe equivalent sized PVC pipe.
4, 6, 8, 10, 12 14 16 18 20 24
b d d d d d
For anchoring AWWA C900 DR18 PVC pipe to cast iron valves and fittings having standardized mechanical joints. For anchoring AWWA C900 DR18 PVC bell and spigot pipe joints. For anchoring AWWA C905 DR18 PVC pipe to cast iron valves and fittings having standardized mechanical joints. For anchoring AWWA C905 DR18 PVC bell and spigot pipe joints.
a. Pipe lengths are joined by single-gasketed bell and spigot joints and are to valves or fittings having bell or standardized mechanical joint connections.
North American Pipe Corp, 2801 Post Oak Blvd, Suite 300, Houston TX 77056
AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200 AWWA C905 Pipe DR25, PR 165 AWWA C905 Pipe DR18, PR 235 4, 6, 8, 10, 12 150 (1035) 200 (1380) 165 (1140) 235 (1620) a
4, 6, 8, 10, 12
14, 16
14, 16
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron valves or fittings having bell or standardized mechanical joint connections.
FM Approvals
1-505
Product Designation
Remarks
Northern Pipe Products Inc, 1302 39th Street NW, Fargo ND 58102-2808
AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200 AWWA C905 Pipe DR25 PR 165 AWWA C905 Pipe DR18 PR 235 4, 6, 8, 10, 12 150 (1035) 200 (1380) 165 (1140) 235 (1620) a
4, 6, 8, 10, 12
14, 16
14, 16
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron valves and fittings having bell or standardized mechanical joint connections.
4, 6, 8, 10, 12
150 (1035) 175 (1205) 200 (1380) 150 (1035) 200 (1380)
a, b
10
a, b
4, 6, 8, 10, 12
a, b
6, 8, 10, 12
6, 8
4, 6, 8, 10, 12
16
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron fittings having bell or standardized mechanical joint connections.
Pipelife Jet Stream Inc, 1700 S Lincoln Street, Siloam Springs AR 72761
AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200 4, 6, 8 150 (1035) 200 (1380) a
4, 6, 8
a. Pipe lengths are joined by single-gasketed bell and spigot joints and are joined to valves or fittings having bell or standardized mechanical joint connections.
FM Approvals
1-506
Product Designation
Remarks
Ductile Iron Adapter Flanges for AWWA C-900 PVC pipe. Used to secure plain-ended PVC pipe to flange ended devices in underground mains.
Series RFCA for PVC Adapter Flanges 4, 6, 8, 10, 12 150 (1035) a, b
a. For use with AWWA C900 DR18 Class 150 pipe. b. For use with cast iron pipe equivalent sized PVC pipe. c. Red paint finish.
Royal Pipe Systems, 131 Regalcrest Court Woodbridge, Ontario L4L 8P3, Canada
AWWA C900 Pipe DR18 PC 150
4, 6, 8, 10, 12
150 (1035)
a, b
4, 6, 8, 10, 12
200 (1380)
14, 16, 18
Cobra-Lock Couplings
4, 6, 8, 10, 12
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron fittings having standardized bell or mechanical joint connections. b. When supplied with grooved ends, this pipe is Approved for use with Royal Pipe Systems Cobra-Lock spline couplings.
Sigma Corp, Rte 537 Goldman Dr, Box 300, Cream Ridge NJ 08514
PV-LOK ductile iron Restraints for AWWA C900 PVC pipe. Restraints used to secure spigot ends of AWWA C900 PVC pipe into standardized mechanical joint-ended pipe fitting or other component.
PVM 4, 6, 8, 10 150 (1035) a, b
Restraints used to secure bell and spigot joints in AWWA C900 PVC pipe.
PVP 4, 6, 8 150 (1035) a, b
Restraints used to secure spigot ends of AWWA C900 PVC pipe in AWWA C905/907 gasketed PVC fittings. The Series PVPF is used in conjunction with a Series PVM restrainer.
PVPF 4, 6, 8 150 (1035) a, b
Ductile iron restraints for AWWA C900 PVC pipe. Used to secure spigot ends of AWWA C900 PVC pipe into standardized mechanical joint-ended pipe fitting or other components.
SLC 4, 6, 8, 10, 12 150 (1035) a, b
a. For use with AWWA C900 Class 150 pipe. b. For use with cast iron pipe equivalent sized PVC pipe.
Mechanical Joint Restrainer Gland Mechanical Joint Restrainer Gland Joint Restrainer
4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10
a, b a, b b, d
FM Approvals
1-507
Product Designation
Fitting Description
Joint Restrainer Mechanical Joint Restrainer Gland Mechanical Joint Restrainer Gland Restrained Adapter Flange Restrained Adapter Flange
150 (1035) 150 (1035) 200 (1375) 150 (1035) 200 (1380)
b, d a, b a, c b, e c, e
Used to join plain ended AWWA C900 PVC pipe to mechanical joint ended devices in underground fire service mains. Pressure rating for use with AWWA C900 DR18 PVC pipe. Pressure rating for use with AWWA C900 DR14 PVC pipe. Restrainer Joints to maintain bell and spigot joint integrity in underground mains or at the base only of a sprinkler riser or with a mechanical joint fitting. Used to join plain ended AWWA C900 PVC pipe to flanged devices in underground fire service mains.
4, 6, 8, 10
150 (1035)
a. For use with AWWA C900 PC150 pipe and standardized mechanical joint fittings.
Uni-Flange, Sub Ford Meter Box Co Inc, Box 443, Wabash IN 46992
Ductile iron restrainers for AWWA C900 PVC pipe. Used to secure spigot ends of AWWA C900 PVC pipe into standardized mechanical joint-ended pipe, fitting or other components.
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
4, 6, 8, 10 4, 6, 8, 10, 12
a, c b, c
Ductile iron restrainers for bell and spigot AWWA C900 PVC pipe joints.
Series 1390C 4, 6, 8 150 (1035) a, c
a. For use with AWWA C900 DR18 Class 150 pipe. b. For use with AWWA C900 Class 150 and 200 PVC pipe. c. For use with cast iron pipe equivalent sized PVC pipe.
4, 6, 8, 10, 12
a, b
4, 6, 8, 10, 12
a, b
a. Pipe lengths are joined by single-gasketed bell and spigot joints and can be joined to cast iron fittings having bell or standardized mechanical joint connections. b. Gulf Rubber or S&B Technical Products Gaskets available.
4, 6, 8, 10, 12
4, 6, 8, 10
b. Pipe lengths are joined by single-gasketed bell and spigot joints and are joined to valves or fittings having bell or standardized mechanical joint connections.
FM Approvals
1-508
Product Designation
Remarks
Vulcan Plastics Corp, 207 Durham Dr, Breeding Industrial Park, Athens AL 35611
AWWA C900 Pipe DR18 PC 150 AWWA C900 Pipe DR14 PC 200 AWWA C905 Pipe DR18 PR 235
4, 6, 8, 10, 12
4, 6, 8, 10, 12
16
a. Pipe lengths are joined by single-gasketed bell and spigot joints and are joined to cast iron fittings.
Remarks
Sweep Bend Fittings, 90, 60, 45, 30, 22, 11, Extruded and Formed SDR 11
63, 75, 90, 110, 125, 140, 160, 180, 200, 225, 250, 280, 315, 355, 400 90, 110, 125, 140, 160, 180, 225, 250, 315
12 (175)
a, b, c
12 (175)
a, b, c
Remarks: a. Dimensions refer to the pipe outside diameter. Pipe and fittings are directly connected by the butt fusion process, or the socket electro-fusion welding process. b. The manufacturer fusion welding instructions must be strictly adhered to for a proper joint. c. The color of the pipe is Black or Blue.
Remarks
63, 90, 110, 125, 140, 160, 180, 225, 250, 315 63, 90, 110, 125, 140, 160, 180, 225, 250, 315 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400 63, 90, 110, 125, 140, 160, 180, 225, 250, 315 63 x 50, 90 x 63 110 x (63, 90) 125 x (90,110) 160 x (63, 90,110) 180 x (90,110,160) 225 x (90,110,160,180) 315 x (110,160,225,250) 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400, 450, 500 125 x 63 140 x (63,90,110) 160 x 125 180 x (63,75,125), 225 x 125 250 x (110,160)
a, b, c
a, b, c
a, b, c
12 (175) 12 (175)
a, b, c
a, b, c
12 (175)
a, b, c
12 (175)
a, b, c
FM Approvals
1-509
Product Designation
Remarks
Blind Flange
63, 90, 110, 125, 140, 160, 180, 225, 250, 315 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400 110, 125, 180, 250 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400 90 x 63 110 x (63,90) 125 x (63, 90,110) 140 x 125 160 x (90,110,125,140) 180 x (125,160) 225 x 160 250 x (160,225) 280 x 250 315 x (225,250) 90 x 63 110 x (63,90) 125 x (63,90,110) 140 x (90,110,125) 160 x (90,110, 125,140) 180 x (90,110,125, 140, 160, 180) 225 x (140, 160, 180) 250 x (160,180,225) 315 x (225,250) 355 x (225,250,315) 400 x (225,250, 315, 355) 63, 90, 110, 125, 140, 160, 180, 225, 250, 315, 355, 400
12 (175) 12 (175)
a, b, c
a, b, c
12 (175) 12 (175)
a, b, c, d a, b, c
12 (175)
a, b, c
12 (175)
a, b, c
12 (175)
a, b, c
12 (175)
a, b, c
Remarks: a. Dimensions refer to the pipe outside diameter. Pipe and fittings are directly connected by the butt fusion process. b. The manufacturers fusion welding instructions must be strictly adhered to for a proper joint. The fittings may also be joined to other FM Approved flanged fittings with the above flange adapters. c. The fittings are manufactured of injection molded PE100. d. The fittings are Approved when used with an EPDM Gasket supplied by AGRU Kunststofftechnik. Product Designation O.D., Pipe Size, mm Pressure Rating Bar (psi)
Remarks
Equal Coupling
End Cap
Remarks:
63, 90, 110, 125, 160, 180, 225 63, 90, 110, 125, 160, 180, 225 63, 90, 110, 125, 160, 180, 225 9063 110(63, 90) 12590 160(90, 110) 180125 225160 63, 90, 110, 125, 160, 180, 225, 250, 315, 355, 400, 450, 500 63, 90, 110, 125, 160, 180, 225
a, b, c a, b, c a, b, c a, b, c
12 (175)
a, b, c
12 (175)
a, b, c
a. Dimensions refer to the pipe outside diameter. The pipe fits into a socket in the fitting, and when electrical current is applied to the terminal, which is integral with the fitting, the joint is completed. b. The manufacturers electro-fusion welding instructions must be strictly adhered to for a proper joint. c. The fittings are manufactured of injection molded PE100.
FM Approvals
1-510
Flange Adapter Class 150 Flange Adapter Class 200 DI Backup Ring Class 150 DI Backup Ring Class 200 90 Elbow Class 150 90 Elbow Class 200 45 Elbow Class 150 45 Elbow Class 200 Tee Class 150 Tee Class 200 End Cap Class 150 End Cap Class 200 Concentric Reducer Class 150 Concentric Reducer Class 200 MJ Adapter Class 150 MJ Adapter Class 200 Transition Fittings Class 150 Transition Fittings Class 200 Electrofusion Coupling Class 200 Electrofusion Branch Saddles Class 150 Electrofusion Branch Saddles Class 200
4, 6, 8, 10, 12, 14, 16, 18, 20, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 4, 6, 8, 10 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4. 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8 64, 86, 108, 1210 64, 86, 108, 1210 4, 6, 8, 10, 12 4, 6, 8, 10, 12 4, 6, 8, 10, 12 6, 8, 10, 12, 16 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 42, 44, 62 64, 82 44, 64
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 200 (1380) 150 (1035) 200 (1380)
a a a a a a a a a a a a a a a a b b c c c
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The fittings may also be joined to other FM Approved flanged pipe and fittings by using the listed flange adapters. b. Provides transition between polyethylene pipe or fittings, using the butt fusion process, to threaded steel pipe or steel pipe provided with a weld-end or flanged. c. The electrofusion couplings are designed to join two adjacent lengths of high density polyethylene pipe. The electrofusion branch saddles mount directly on the outside diameter of lengths of high density polyethylene pipe. The Central Electrofusion System is used to fuse couplings and branch saddles to the pipe. Manufacturers installation and assembly recommendations must be strictly followed for a proper joint.
Extrumex S.A., de C.V. Lerdo de Tejada, No. 899 Col. El Lechugal, Santa Catarina N.L., C.P. 66350, Mexico
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Pipe, Class 150 Pipe, Class 200 Molded Tee, Class 150 Molded Tee, Class 200 Molded 90 Elbow, Class 150 Molded 90 Elbow, Class 200 Molded 45 Elbow, Class 150 Molded 45 Elbow, Class 200 Molded Concentric Reducer, Class 150
4, 6, 8, 10, 12, 14, 16, 18, 20 4, 6, 8, 10, 12, 14, 16 and 18 4 and 6 4 and 6 4 and 6 4 and 6 4 and 6 4 and 6 64, 84, 86, 106, 108, 128, 1210, 1410, 1412, 1612, 1614, 1814, 1816, 20x18 64, 84, 86, 106, 108, 128, 1210, 1410, 1412, 1612, 1614, 1814, 1816, 20x18
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035)
a, b a, b a, b a, b a, b a, b a, b a, b a, b
200 (1380)
a, b
FM Approvals
1-511
Product Designation
Remarks
Molded Stub End, Class 150 Ductile Iron Backup Ring, Class 150 Molded Stub End, Class 200 Ductile Iron Backup Ring, Class 200 Fabricated Equal Tee, Class 150 Fabricated Equal Tee, Class 200 Fabricated 90 Elbow, Class 150 Fabricated 90 Elbow, Class 200 Fabricated 45 Elbow, Class 150 Fabricated 45 Elbow, Class 200
4, 6, 8, 10, 12, 14, 16, and 18 4, 6, 8, 10, 12, 14, 16, and 18 4, 6, 8, 10, 12, 14, 16, and 18 4, 6, 8, 10, 12, 14, 16, and 18 8, 10, 12, 14, 16, and 18 8, 10, 12, 14, 16, and 18 8, 10, 12, 14, 16, 18, 20 8, 10, 12, 14, 16, and 18 8, 10, 12, 14, 16, 18, 20 8, 10, 12, 14, 16, and 18
150 (1035) 150 (1035) 200 (1380) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380)
a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. b. The diameter basis for pipe and fittings is Mexican Standard NMX-E-18 which is dimensionally equivalent to IPS sizes.
200 (1380)
a. FRIALEN Safety Fittings are electrofusion coupler fittings designed to join two adjacent lengths of high density polyethylene pipe. The FRIAMAT family of fusion machines are used to fuse FRIALEN fittings to the pipe. Manufacturers installation and assembly recommendations must be strictly followed for a proper joint.
ISCO Industries LLC, 926 Baxter Ave, Box 4545, Louisville KY 40204
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Class 150 Tees Molded IPS Class 200 Tees Molded IPS Class 150, 90 Elbows Molded IPS Class 200, 90 Elbows Molded IPS Class 150, 45 Elbows Molded IPS Class 200, 45 Elbows Molded IPS Class 150 Concentric Molded Reducer
2, 3, 4, 6
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035)
2, 3, 4, 6
2, 3, 4, 6
2, 3, 4, 6
3, 4, 6
3, 4, 6
32, 43, 64, 86, 108, 1210, 1412, 1614, 1816 32, 43, 64, 86, 108, 1210, 1412, 1614, 1816 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18
200 (1380)
Class 150 Flange Adapter, Molded IPS Class 200 Flange Adapter, Molded IPS Class 150 Ductile Iron Backup Rings Class 200 Ductile Iron Backup Rings
FM Approvals
1-512
Product Designation
Remarks
32, 42, 43, 62, 63, 64, 82, 83, 84, 86, 102, 103, 104, 106, 108, 122, 123, 124, 126, 128, 1210, 142, 143, 144, 146, 148, 1410 162, 163, 164, 166 168, 1610, 1612, 182, 183, 184, 186, 188, 1810, 1812 32, 42, 43, 62, 63, 64, 82, 83, 84, 86, 102, 103, 104, 106, 108, 122, 123, 124, 126, 128, 1210, 142, 143, 144, 146, 148, 1410 162, 163, 164, 166 168, 1610, 1612, 182, 183, 184, 186, 188, 1810, 1812 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18
150 (1035)
200 (1380)
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035)
Class 150 Fabricated 90 Elbow (5 segments) Class 200 Fabricated 90 Elbow (5 segments) Class 150 Fabricated 45 Elbow (3 segments) Class 200 Fabricated 45 Elbow (3 segments) Class 150 Fabricated 90 Elbow (3 segments) Class 200 Fabricated 90 Elbow (3 segments) Class 150 Fabricated 45 Elbow (2 segments) Class 200 Fabricated 45 Elbow (2 segments) Class 150 Mechanical Joint Adapter
200 (1380)
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The pipe and fittings may also be joined to other FM Approved steel flanged pipe and fittings by using the listed flange adapters. b. Pipe and adapter, with ductile iron gland ring attached, are directly connected by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The polyethylene fitting, gland ring, gasket, and T-Head bolts are provided in a kit for field installation, which allows attachment to a compatible flange with ductile iron pipe.
Independent Pipe Products Inc, 4949 Joseph Hardin Drive, Dallas TX 75236
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa)
Remarks
Class 150 Tees Molded IPS Class 200 Tees Molded IPS
2, 3, 4, 6
2, 3, 4, 6
FM Approvals
1-513
Product Designation
Remarks
Class 150, 90 Elbows Molded IPS Class 200, 90 Elbows Molded IPS Class 150, 45 Elbows Molded IPS Class 200, 45 Elbows Molded IPS Class 150 Concentric Molded Reducer Class 200 Concentric Molded Reducer Class 150 Flange Adapter, Molded IPS Class 200 Flange Adapter, Molded IPS Class 150 Ductile Iron Backup Rings Class 200 Ductile Iron Backup Rings Class 150 Branch Saddle Reducing Tee
2, 3, 4, 6
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035)
2, 3, 4, 6
3, 4, 6
3, 4, 6
32, 43, 64, 86, 108, 1210, 1412, 1614, 1816 32, 43, 64, 86, 108, 1210, 1412, 1614, 1816 2, 3, 4, 6, 8, 10, 12, 14, 16, 18
32, 42, 43, 62, 63, 64, 82, 83, 84, 86, 102, 103, 104, 106, 108, 122, 123, 124, 126, 128, 1210, 142, 143, 144, 146, 148, 1410, 162, 163, 164, 166, 168, 1610, 1612, 182, 183, 184, 186, 188, 1810, 1812 32, 42, 43, 62, 63, 64, 82, 83, 84, 86, 102, 103, 104, 106, 108, 122, 123, 124, 126, 128, 1210, 142, 143, 144, 146, 148, 1410, 162, 163, 164, 166, 168, 1610, 1612, 182, 183, 184, 186, 188, 1810, 1812 8, 10, 12, 14, 16, 18
200 (1380)
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035)
Class 150 Fabricated 90 Elbow (5 segments) Class 200 Fabricated 90 Elbow (5 segments) Class 150 Fabricated 45 Elbow (5 segments) Class 200 Fabricated 45 Elbow (3 segments) Class 150 Fabricated 90 Elbow (3 segments) Class 200 Fabricated 90 Elbow (3 segments) Class 150 Fabricated 45 Elbow (2 segments) Class 200 Fabricated 45 Elbow (2 segments) Class 150 Mechanical Joint Adapter
FM Approvals
1-514
Product Designation
Remarks
200 (1380)
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The pipe and fittings may also be joined to other FM Approved steel flanged pipe and fittings by using the listed flange adapters. b. Pipe and adapter, with ductile iron gland ring attached, are directly connected by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The polyethylene fitting, gland ring, gasket, and T-Head bolts are provided in a kit for field installation, which allows attachment to a compatible flange with ductile iron pipe.
Remarks
Molded Fittings Elbow, 90 Elbow, 90 Elbow, 45 Elbow, 45 Equal Tee Equal Tee End Cap End Cap Concentric Reducer Concentric Reducer Flange Adapter Flange Adapter Stub End Stub End Fabricated Fittings Elbows 90 Elbows 90 Equal Tee Equal Tee 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 10, 12, 14, 16, 18, 20, 22, 24 10, 12 , 14, 16, 18, 20, 22, 24 2 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 3 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 6 8, 10, 12, 14, 16, 18, 20, 22, 24 8 10, 12, 14, 16, 18, 20, 22, 24 10 14, 16, 18, 20, 22, 24, 12 16, 18, 20, 22, 24 2 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 3 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 6 8, 10, 12, 14, 16, 18, 20, 22, 24 8 10, 12, 14, 16, 18, 20, 22, 24 10 14, 16, 18, 20, 22, 24 12 16, 18, 20, 22, 24 10, 12 10, 12 10 8, 12 8, 12 10, 14 12, 16 12, 16 14, 18 14, 18 16 10 8, 12 8, 12 10 150 (1035) 200 (1380) 150 (1035) 200 (1380) a, b a, b a, b a, b 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 2, 3, 4, 6, 8 3 2, 4 2, 4 3, 6 4, 8 6 3 2, 4 2, 4 3, 6 4, 8 6 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b
150 (1035)
a, b
200 (1380)
a, b
a, b a, b a, b a, b
FM Approvals
1-515
Product Designation
Remarks
Swage Reducer
10 8, 12 8, 12 10, 14 10, 14 12, 16 12, 16 14, 18 14, 18 16, 20 16, 20 18, 22 18, 22 20, 24 20, 24 22 10 8, 12 8, 12 10, 14 10, 14 12, 16 12, 16 14, 18 14, 18 16, 20 16, 20 18, 22 18, 22 20, 24 20, 24 22 14, 16, 18, 20, 22, 24 14, 16, 18, 20, 22, 24 14, 16, 18, 20, 22, 24 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 , 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 , 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18 , 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4 2, 3, 4 2, 3, 4 2, 3, 4
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380)
a, b
Swage Reducer Flange Adapters Flange Adapters Stub Ends Stub Ends Beveled Flange Adapter Beveled Flange Adapter Mechanical Joint Adapter Mechanical Joint Adapter Wall Anchor Wall Anchor Back-Up Rings DI Convoluted Back-Up Rings DI Convoluted Back-Up Rings SS Convoluted Back-Up Rings SS Convoluted Back-Up Rings Forged Carbon Steel Back-Up Rings Forged Carbon Steel Blind Flanges Forged Carbon Steel Blind Flanges Forged Carbon Steel Transition, HDPE Steel Pipe, SS Transition, HDPE Steel Pipe, SS Transition, HDPE Steel Pipe, Brass Transition, HDPE Steel Pipe, Brass
Remarks
a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b a, b
a. Fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The fittings may also be joined to other FM Approved flanged pipe and fittings by using the listed flange adapters and back-up rings. b. FM Approved with a diameter basis of IPS sizes.
KWH Pipe (Canada) Ltd, 6507 Mississauga Rd, Mississauga, Ontario L5N 1A6, Canada
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Sclairpipe DR11 Class 150 Sclairpipe DR9 Class 200 Stub-Ends Class 150 Flange Adapters Class 150 Specialty Ductile Iron Back-Up Flanges Class 150
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28
150 (1035) 200 (1380) 150 (1035) 150 (1035) 150 (1035)
a, b a, b a,b a,b b
FM Approvals
1-516
Product Designation
Remarks
Steel Plate Back-Up Flanges Class 150 Stub-Ends Class 200 Flange Adapters Class 200 Specialty Ductile Iron Back-Up Flanges Class 200 Steel Plate Back-Up Flanges Class 200 Blind Flange, Steel Blind Flange, Steel Fabricated Elbows 90 Class 150 Fabricated Elbows 90 Class 200 Fabricated Tees Class 150 Fabricated Tees Class 200
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 884, 10106, 10104, 12128, 12126, 12124, 141410, 14148, 14148, 14146, 14144, 161612, 161610, 16168, 16166, 16164, 181812, 181810, 18188, 18186, 18184, 202012, 202010, 20208, 20206, 20204, 222212, 222210, 22228, 22226, 22224 242412, 242410, 24248, 24246, 24244, 282812, 282810, 28288, 28286, 28284 64, 84, 86, 108, 1210, 1410, 1412, 1612, 1614, 1814, 1816, 2016, 2018, 2218, 2220, 2420, 2422, 2624, 2824, 2826 64, 84, 86, 108, 1210, 1410, 1412, 1612, 1614, 1814, 1816, 2016, 2018, 2220, 2422, 2624, 2824, 2826 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 24, 28 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4, 6, 8, 10, 12, 14, 16, 18, 20 43, 63, 64, 84, 86, 106, 108, 1210, 1412, 1612, 1614, 1814, 1816, 2016, 2018, 2218, 2220, 2420, 2422, 2824 4x2, 6x3, 84, 106, 128, 1410, 1612 443, 663, 664, 884, 886, 10106, 10108, 121210, 141412, 161612, 161614, 181814, 181816, 202016, 202018, 222218, 222220, 242420, 242422, 282824
150 (1035) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380)
b a, b a, b a, b a, b a, b a, b a, b a, b
150 (1035)
a, b
Concentric Reducers Class 150 Concentric Reducers Class 200 Butterfly Valve Spacer Rings Class 150 Butterfly Valve Spacer Rings Class 200 Repair Couplings Class 150 Repair Couplings Class 200 Reducers with Leg Extensions Class 150 Sidewall Fusion Fitting with Leg Extensions Class 150 Straight Tees with Reducer Outlet and Leg Extensions Class 150
150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380) 150 (1035) 150 (1035) 150 (1035)
a, b
a, b b b b b a, b
a, b
a, b
a. Pipe and fittings may be directly connected together by the Butt Fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. The Pipe and Fittings may also be joined to other FM Approved steel flanged pipe and fittings by using the above listed flange adapters. b. The diameter basis is IPS sizes.
Performance Pipe, A Division of Chevron Phillips Chemical Company LP, 5085 West Park Blvd, Suite 500, Plano TX 75093
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
DRISCOPLEX 1500 IPS Class 150 Pipe DRISCOPLEX 1500 IPS Class 200 Pipe DRISCOPLEX 1600 DIPS Class 150 Pipe DRISCOPLEX 1600 DIPS Class 200 Pipe
2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24
a, b, g
a, b, g
a, b, g
a, b, g
FM Approvals
1-517
Product Designation
Remarks
2, 3, 4, 6, 8
150 (1035) 150 (1035) 150 (1035) 150 (1035) 150 (1035)
a, b, c
Equal Tees
2, 3, 4, 6, 8
a, b
End Caps
2, 3, 4, 6, 8
a, b
Flange Adapters
a, b
Molded Reducers
a, b
2, 3, 4, 6, 8
a, b, c
Equal Tees
2, 3, 4, 6, 8
a, b
End Caps
2, 3, 4, 6, 8
a, b
Flange Adapters
22, 33, 44, 66, 88, 1010, 1212, 1414, 1616 32, 42, 43, 64, 86
a, b
Molded Reducers
200 (1380) 150 (1035) 200 (1380) 150 (1035) 200 (1380)
a, b
Back-Up Rings (IPS) (IPS) (DIPS) (DIPS) Back-Up Rings, Carbon Steel (IPS) (IPS)
Remarks:
2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4, 6, 8, 10, 12, 14, 16, 18, 20
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturer fusion instructions must be strictly followed for a proper fusion joint. b. The pipe and fittings may also be provided with flange adapters and back-up rings and bolted together. Back-up rings must be pressure rated at or above the pressure rating of the pipe on which they are installed. g. Pipe may be supplied as black, or with red stripe, or with blue stripe. i = Pipe may be marked with the FM Approval Mark and NSF or the FM Approval Mark and AWWA.
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24 4, 6, 8, 10, 12
150 (1035) 200 (1380) 150 (1035) 150 (1035) 200 (1380)
Flange Adaptors Class 150 Flange Adaptor with Back up Rings Class 150 Flange Adaptor with Back up Rings Class 200
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 4, 6, 8, 10, 12, 14, 16, 18, 20, 24
FM Approvals
1-518
Product Designation
Remarks
4, 6, 8, 10, 12
200 (1380)
a. Pipe and fittings may be directly connected together by the butt fusion process. Manufacturers fusion instructions must be strictly followed for a proper fusion joint. The pipe and fittings may also be joined to other Approved steel flanged pipe and fittings by using the above listed flange adapters.
Style 994 Flanges Style 995 Couplings Style 997 Couplings Style 995T Transition Fittings Style 43 Transition Nipples
200 (1725) 200 (1725) 200 (1725) 200 (1725) 200 (1725)
For use with FM Approved polyethylene pipe in Class 150 and Class 200 wall thicknesses. Style 06 and 60 end caps may be used with Style 997 couplings to close a line.
Style 994 Flanges Style 995 Couplings Style 997 Couplings Style 995T Transition Fittings Style 43 Transition Nipples
200 (1725) 200 (1725) 200 (1725) 200 (1725) 200 (1725)
For use with FM Approved polyethylene pipe in Class 150 and Class 200 wall thicknesses. Style 06 and 60 end caps may be used with Style 997 couplings to close a line.
Pipe, glass reinforced vinylester (GRV) P/000/01A Pipe, glass reinforced epoxy (GRE) P/000/01B 90 Elbows Series B90 45 Elbows Series B45 2212 Elbows Series B22.5 Equal Tees T/000/01A through T/000/07B
16 (232)
a, b, g
16 (232)
a, b, g
100 through 600 (4 through 24) 100 through 600 (4 through 24) 100 through 600 (4 through 24) 100 through 600 (4 through 24)
a, b, c, d, e, f, g, h
a, b, c, d, e, f, g, h
a, b, c, d, e, f, g, h
a, b, c, d, e, f, g, h
FM Approvals
1-519
Product Designation
Remarks
Unequal Tees T/000/08A through T/000/014B Concentric Reducers CR/000/01A through CR/000/05B Eccentric Reducers ER/000/01A through ER/000/05B Taper Coupling for Cemented Joints C/000/01A and C/000/01B Pipe, Bell and Spigot with Lock Strip Joint, glass reinforced vinylester (GRV) P/000/02A Pipe, Bell and Spigot with Lock Strip Joint, glass reinforced epoxy (GRE) P/000/02B Double Bell Coupling with Lock Strip Joint (GRE and GRV) J/000/03, J/000/04
16 (232)
a, b, c, d, e, f, g, h
16 (232)
a, b, c, d, e, f, g, h
16 (232)
a, b, c, d, e, f, g, h
16 (232)
a, e, f, g
16 (232)
f, g, i
16 (232)
e, g, i
16 (232)
e, f, g, j
a. Tapered Spigot Joint (cemented epoxy joint using internally tapered coupling, CIBA Araldite 2014 [AW139/XB5323] two component adhesive). b. Laminated Joint (plain ends using hand lay-up of 4 glass cloth overlays with Vinylester resin, or epoxy resin). c. Flat Flange. d. Stub End. e. Glass Reinforced Epoxy (GRE). f. Glass Reinforced Vinylester (GRV). g. Sizes: 100, 150, 200, 250, 300, 350, 400, 500, and 600 millimeters (4, 6, 8, 10, 12, 14, 16, 20 and 24 in. NPS). h. Fitting incorporates any combination of a, b, c, and d ends. i. Mechanical joint pipe with one integral Lock Strip male (spigot) end and one integral Lock Strip female (bell) end. Lock Strip consists of nylon strip in grooved connection. j. Mechanical joint with an integral Lock Strip female (bell) on both ends. Lock Strip consists of nylon strip in grooved connection.
Ameron Fiberglass-Composite Pipe Group/Europe, Box 6, 4190 CA Geldermalsen, The Netherlands (NE)
Product Designation Nominal Pipe Size, in. Pressure Rating bar (psi) Remarks
Bondstrand Series 2212 Coupling S37691 S37692 S37693 S37694 S37695 8 10 12 14 16 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) b b b b b
Bondstrand Series 2420 Key Lock Pipe S229N33D5 S339N33D5 S449N33D5 S669N33D5 2 3 4 6 20 (290) 20 (290) 20 (290) 20 (290) a a a a
Bondstrand Series 2420 Taper Taper Pipe S229N33G9 S339N33G9 S449N33G9 S669N33G9 2 3 4 6 20 (290) 20 (290) 20 (290) 20 (290) e, i e, i e, i e, i
FM Approvals
1-520
Product Designation
Remarks
2 3 4 6
e, j e, j e, j e, j
Bondstrand Series 3414 FM Key Lock Pipe, 20 S338L33A2 S448L33A2 S668L33A2 S888L33A2 SAA8L33A2 SBB8L33A2 SCC8L33B5 SDD8L33B5 SEE8L30A2 SFF8L33B5 3 4 6 8 10 12 14 16 18 20 14 (200) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (200) 14 (200) a a a a a a a a a a
Bondstrand Series 3414 Key Lock Pipe, 40 S888L35A2 SAA8L35A2 SBB8L35A2 SCC8L35B5 SDD8L35B5 SEE8L35B5 SFF8L35B5 8 10 12 14 16 18 20 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) a a a a a a a
Bondstrand Series 3414 Taper Taper Pipe, 20 S228L33G9 S338L33G9 S448L33G9 S668L33G9 S888L33G9 SAA8L33G9 SBB8L33G9 SCC8L33G9 SDD8L33G9 SEE8L30G9 SFF8L30G9 SHH8L30G9 2 3 4 6 8 10 12 14 16 18 20 24 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200)a 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) i, k i, k i, k i, k i, k i, k i, k i, k i, k i, k a i, k
Bondstrand Series 3414 Taper Taper Pipe, 40 S888L35G9 SAA8L35G9 SBB8L35G9 8 10 12 14 (200) 14 (200)a 14 (200) i, k i, k i, k
FM Approvals
1-521
Product Designation
Remarks
14 16 18 20 24
i, k i, k i, k a i, k
Bondstrand Series 3414/3416 Key Lock Reducing Tee S648M83D4 S848M83D4 S868M83D4 SA48M83D4 SA68M83D4 SB48M83D4 SB68M83D4 SC48M83D3 SC68M83D3 SD48M83D3 SD68M83D3 664 884 886 10104 10106 12124 12126 14144 14146 16164 16166 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) b b b b b b b b b b b
Bondstrand Series 3414 Key Lock Coupling S228L07D4 S338L07D4 S448L07D4 S668L07D4 S888L07D4 SAA8L07D4 SBB8L07D4 SCC8L07D4 SDD8L07D4 SEE8L07E5 SFF8L07E5 2 3 4 6 8 10 12 14 16 18 20 14 (200) 14 (200) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (200) 14 (200) b b b b b b b b b b b
Bondstrand Series 3414 Key Lock Nipple S228L28A1 S338L28A1 S448L28A1 S668L28A1 S888L28A1 SAA8L28A1 SBB8L28A1 SCC8L28A1 SDD8L28B4 SEE8L28B4 2 3 4 6 8 10 12 14 16 18 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200)a 14 (200) 14 (200) 14 (200) 14 (200) l l l l l l l l l l
FM Approvals
1-522
Product Designation
Remarks
SFF8L28B4 Bondstrand Series 3414 Taper Taper Coupling S228L07J8 S338L07J8 S448L07J8 S668L07J8 S888NL07J8 SAA8L07J8 SBB8L07J8 SCC8L07J8 SDD8L07J8 SEE8L07J8 SFF8L07J8 SHH8L07J8
20
14 (200)
2 3 4 6 8 10 12 14 16 18 20 24
14 (200) 14 (200) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (200) 14 (200) 14 (200)
f, j f, j f, j f, j f, j f, j f, j f, j f, j f, j f, j f, j
Bondstrand Series 3414 Key Lock Adapter S5288100 S5188200 S5188300 S5188400 S5388500 S5188650 S5188750 4 6 8 10 12 14 16 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) d, e d, e d, e d, e d, e d, e d, e
Bondstrand Series 3414 Key Lock Adapter Reducer S5505000 S5505100 S5505200 S5505300 S5505400 S5505600 S5605700 S5605800 S5606000 64 84 86 106 108 1210 1410 1412 1614 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) 14 (205) c c c c c c c c c
Bondstrand Series 3416 Key Lock Pipe, 20 S338M33A2 S448M33A2 S668M33A2 S888M33A2 SAA8M33A2 SBB8M33A2 SCC8M33B5 3 4 6 8 10 12 14 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) a a a a a a a
FM Approvals
1-523
Product Designation
Remarks
SD8M33B5 SFF8M33B5
16 20
16 (230) 16 (230)
a a
Bondstrand Series 3416FM Key Lock Pipe, 40 S888M35A2 SAA8M35A2 SBB8M35A2 SCC8M35B5 SDD8M35B5 SEE8M35B5 SFF8M35B5 8 10 12 14 16 18 20 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (200) 16 (200) a a a a a a a-
Bondstrand Series 3416 Taper Taper Pipe, 20 S228M33G9 S338M33G9 S448M33G9 S668M33G9 S888M33G9 SAA8M33G9 SBB8M33G9 SCC8M33G9 SDD8M33G9 SEE8M30G9 SFF8M30G9 SHH8M30G9 2 3 4 6 8 10 12 14 16 18 20 24 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) i i i i i i i i i i i i
Bondstrand Series 3416 Taper Taper Pipe, 40 S888M35G9 SAA8M35G9 SBB8M35G9 SCC8M35G9 SDD8M35G9 SEE8M35G9 SFF8M35G9 SHH8M35G9 8 10 12 14 16 18 20 24 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) i i i i i i i i
Bondstrand Series 3416 Key Lock Reducing Tee S5264030 S5264130 S5264140 S5264230 S5264240 S5264330 S5264340 664 884 886 10104 10106 12124 12126 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) b b b b b b b
FM Approvals
1-524
Product Designation
Remarks
b b b b
Bondstrand Series 3416 Key Lock Adapter S5288100 S5188200 S5280300 S5388400 S5388500 S5188650 S5388700 4 6 8 10 12 14 16 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) d, e d, e d, e d, e d, e d, e d, e
Bondstrand Series 3416 Key Lock Coupling S228M07D4 S338M07D4 S448M07D4 S668M07D4 S888M07D4 SAAM07D4 SBB8M07D4 SCC8M07E5 SDD8M07E5 SEE8M07E5 SFF8M07E5 2 3 4 6 8 10 12 14 16 18 20 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) b b b b b b b b b b b
Bondstrand Series 3416 Key Lock Nipple S228M28A1 S338M28A1 S448M28A1 S668M28A1 S888M28A1 SAA8M28A1 SBB8M28A1 SCC8M28A1 SDD8M28B4 SEE8M28B4 SFF8M28B4 2 3 4 6 8 10 12 14 16 18 20 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) l l l l l l l l l l l
Bondstrand Series 3416 Taper Taper Coupling S228M07J8 S338M07J8 S448M07J8 2 3 4 16 (230) 16 (230) 16 (230) f, j f, j f, j
FM Approvals
1-525
Product Designation
Remarks
6 8 10 12 14 16 18 20 24
f, j f, j f, j f, j f, j f, j f, j f, j f, j
Bondstrand Series 3416 Key Lock Adapter Reducer S5505000 S5505100 S5505200 S5505300 S5505400 S5505600 S5605700 S5605800 S5606000 64 84 86 106 108 1210 1410 1412 1614 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) c c c c c c c c c
Bondstrand Series 3420 Key Lock Pipe, 20 S338N33A2 S448N33A2 S668N33A2 S888N35B5 SAA8N31B5 SBB8N30B5 SCC8N33B5 SDD8N33B5 SEE8N30A2 SFF8N33B5 3 4 6 8 10 12 14 16 18 20 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) a a a a a a a a a a
Bondstrand Series 3420FM Key Lock Pipe, 40 S888N35B5 SAA8N35B5 SBB8N35B5 SCC8N35B5 SDD8N35B5 SEE8N35A2 SFF8N35B5 8 10 12 14 16 18 20 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) a a a a a a a
FM Approvals
1-526
Product Designation
Remarks
S338N33G9 S448N33G9 S668N33G9 S888N33G9 SAA8N33G9 SBB8N33G9 SCC8N33G9 SDD8N33G9 SEE8N30G9 SFF8N30G9 SHH8N30G9
3 4 6 8 10 12 14 16 18 20 24
20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290)
e, i e, i e, i e, i e, i e, i e, i e, i e, i e, i e, i
Bondstrand Series 3420 Taper Taper Pipe, 40 S888N35G9 SAA8N35G9 SBB8N35G9 SCC8N35G9 SDD8N35G9 SEE8N35G9 SFF8N35G9 SHH8N35G9 8 10 12 14 16 18 20 24 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) e, i e, i e, i e, i e, i e, i e, i e, i
Bondstrand Series 3420 Key Lock Coupling S228N07D4 S338N07D4 S448N07E5 S668N07E5 S888N07E5 SAA8N07E5 SBB8N07E5 SCC8N07E5 SDD8N07E5 SEE8N07E5 SFF8N07E5 2 3 4 6 8 10 12 14 16 18 20 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b b
Bondstrand Series 3420 Key Lock Nipple S228N28A1 S338N28A1 S448N28B4 S668N28B4 S888N28B4 SAA8N28B4 SBB8N28B4 2 3 4 6 8 10 12 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) l e, i e, i e, i e, i e, i e, i
FM Approvals
1-527
Product Designation
Remarks
14 16 18 20
e, i e, i e, i e, i
Bondstrand Series 3420 Taper Taper Coupling S228N07J8 S338N07J8 S448N07J8 S668N07J8 S888N07J8 SAA8N07J8 SBB8N07J8 SCC8N07J8 SDD8N07J8 SEE8N07J8 SFF8N07J8 SHH8N07J8 2 3 4 6 8 10 12 14 16 18 20 24 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) e, j e, j e, j e, j e, j e, j e, j e, j e, j e, j e, j f, j
Bondstrand Series 3440 Key Lock Pipe S228630A2 S338730B5 Bondstrand Series 3440 Taper Taper Pipe S228730G9 S338731G9 2 3 40 (580) 40 (580) i, f i, f 2 3 40 (580) 40 (580) a a
Bondstrand Series 6000 Pipe, 20 S44613463 S66613463 S88613363 SAA613363 SBB613363 SDD613263 4 6 8 10 12 16 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) f, h, i f, h, i f, h, i f, h, i f, h, i f, h, i
a. Pipe with one integral key-lock female end and one integral key-lock male end. b. Fittings with key-lock female ends. c. Fittings with one key-lock female end and one key-lock male end. d. Fittings with tapered spigot end and key-lock male end. e. Bonded joints made with RP-48 adhesive. f. Bonded joints made with RP-34 adhesive. g. Fittings with Quick-lock bell ends. h. Spigot end of pipe must be prepared with Ameron equipment. See manufacturers instructions. i. Pipes equipped with one bell and one spigot end. Pipe lengths joined by bell and spigot joints. j. Coupling equipped with two tapered female ends. k. Bonded joints made with RP-44 adhesive. l. Nipples supplied with two male key-lock ends.
FM Approvals
1-528
Ameron International, Fiberglass Composite Pipe Division The Americas, 1004 Ameron Rd, Burkburnett TX 76354
Bondstrand Series 3200/1, 3200 Pipe and Fittings.
Product Designation Nominal Pipe Size, in. Pressure Rating bar (psi) Remarks
Pipe BellSpigot 20344615 30344615 40344615 60344615 80344615 A0344615 B0344615 C0344615 D0344615
2 3 4 6 8 10 12 14 16
b, d, g, u, v b, d, g, u, v b, d, g, u, v b, d, g, u, v a, b, e, g, s, t a, b, e, g, s, t a, b, e, g, s, t a, b, e, g, s, t a, b, e, g, s, t
2 3 4 6
b, j, l, u, v b, j, l, u, v b, j, l, u, v b, j, l, u, v
Couplings BellBell 20340707 30340707 40340707 60340707 80340707 A0340707 B0340707 C0340707 D0340707
2 3 4 6 8 10 12 14 16
g, h, u, v g, h, u, v g, h, u, v g, h, u, v a, e, g, h, s, t a, e, g, h, s, t a, e, g, h, s, t a, e, g, h, s, t a, e, g, h, s, t
8 10 12 14 16
h, k, m, s, t h, k, m, s h, k, m, s h, k, m h, k, m
2 3 4 6
c, f, g, u, v c, f, g, u, v c, f, g, u, v c, f, g, u, v
FM Approvals
1-529
Product Designation
Remarks
8 10 12 14 16
a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t
8 10 12 14 16
c, h, m, s, t c, h, m, s c, h, m, s c, h, m c, h, m
45 Elbow BellBell 20341507 30341507 40341507 60341507 80341408 A0341408 B0341408 C0341408 D0341408
2 3 4 6 8 10 12 14 16
c, f, g, u, v c, f, g, u, v c, f, g, u, v c, f, g, u, v a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t a, c, g, h, s, t
8 10 12 14 16
c, h, m, s, t c, h, m, s c, h, m, s c, h, m c, h, m
Equal Tee Bell Ends 20348107 30348107 40348107 60348107 80348007 A0348007 B0348007 C0348007 D0348007
2 3 4 6 8 10 12 14 16
c, f, g, u, v c, f, g, u, v c, f, g, u, v c, f, g, u, v a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t
8 10 12 14
c, i, k, m, s, t c, i, k, m, s c, i, k, m, s c, i, k, m
FM Approvals
1-530
Product Designation
Remarks
D0348055
16
12 (175)
c, i, k, m
Blind Flange 20342504 30342504 40342504 60342504 80342504 A0342504 B0342504 C0342504 D0342504
2 3 4 6 8 10 12 14 16
f f f f n n n n n
Flange Ring 20342509 30342509 40342509 60342509 80342509 A0342509 B0342509 C0342509 D0342509
2 3 4 6 8 10 12 14 16
f f f f h h h h h
Stub End 20342510 30342510 40342510 60342510 80342510 A0342510 B0342510 C0342510 D0342510
2 3 4 6 8 10 12 14 16
f, u, v f, u, v f, u, v a, f a, o a, o a, o a, o a, o
32 43 64 82
a, g, h, s, t a, g, h, s, t a, g, h, s, t a, c, e, g, i, s, t
FM Approvals
1-531
Product Designation
Remarks
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
83 84 86 102 103 104 106 108 122 123 124 126 128 1210 142 143 144 146 148 1410 1412 162 163 164 166 168 1610 1612 1614 82 83 84 86 102 103 104 106 108 122 123 124 126
14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200)
a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t c, i, k, m, s, t c, i, k, m, s, t c, i, k, m, s, t c, i, k, m, s, t c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s c, i, k, m, s
FM Approvals
1-532
Product Designation
Remarks
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
128 1210 142 143 144 146 148 1410 1412 162 163 164 166 168 1610 1612 1614
14 (200) 14 (200) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175)
c, i, k, m, s c, i, k, m, s c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m c, i, k, m
Reducing Tee Bell Ends N/A N/A N/A N/A N/A N/A N/A N/A
3 4 6 8 10 12 14 16
a, c, d, g, p, s, t a, c, d, g, p, s, t a, c, d, g, p, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t a, c, e, g, i, s, t
Reducing Tee Pronto-Lock II Mechanical Joint N/A N/A N/A N/A N/A
8 10 12 14 16
c, i, k, m, s, t c, i, k, m, s c, i, k, m, s c, i, k, m c, i, k, m
C.I.P.E. Adapter N/A N/A N/A N/A N/A N/A N/A N/A
3 4 6 8 10 12 14 16
a, h a, h a, h a, h, e a, h, e a, h, e a, h, e a, h, e
FM Approvals
1-533
Product Designation
Remarks
2 3 4 6
l, o, u, v l, o, u, v l, o, u, v l, o, u, v
2 3 4 6
h, l, q, u, v h, l, q, u, v h, l, q, u, v h, l, q, u, v
8 10 12 14 16
a, m, o, r, s, t a, m, o, r, s a, m, o, r, s a, m, o, r a, m, o, r
a. Bonded joints made with C-20 adhesive. b. Commodity code shown for 40 ft nominal length; other lengths available. c. Commodity code shown for like joint configurations. Combinations available. d. Supplied with bonded on coupling (branch only on reducing tees). e. Supplied with wound on bell. f. Parts are molded. g. Flanged assemblies available. h. Parts are filament wound. i. Parts are mitered. j. Supplied with bonded on joint components. k. Supplied with wound on female and bonded on male components. l. Pronto-Lock mechanical joint.
m. Pronto-Lock II mechanical joint. n. Cast iron. Epoxy coating available. o. Parts are cast. p. Reductions made by bushings. q. Includes o-ring. r. Includes threaded sleeve and bearing ring. s. Bonded joints can be made with A20-LT alternative adhesive. t. Bonded joints can be made with B20 alternative adhesive. u. Bonded joints can be made with PSX-20 alternative adhesive. v. Bonded joints can be made with PSX-34 alternative adhesive.
8 10 12
a, b a, b a, b
Pipe-Bell Spigot. Series 6000 Quick-Lock. 22606763 33603763 3679500FM 3679600FM 3679800FM 3679900FM 3680000FM
2 3 8 10 12 14 16
b b a, b a, b a, b a, b a, b
2 3 4 6
k k a a
FM Approvals
1-534
Product Designation
Remarks
8 10 12 14 16
a a a a a
Elbow-90 6000 22602060 33602060 3683300FM 3683400FM 3683500FM 3683600FM 3683700FM 3683800FM 5141700FM
2 3 4 6 8 10 12 14 16
k k a a a a a a a
Elbow-45 6000 22601460 33601460 3684300FM 3684400FM 3684500FM 3684600FM 3684700FM 3684800FM 5128900FM
2 3 4 6 8 10 12 14 16
k k a a a a a a a
2 3
12 (175) 12 (175)
k k
Coupling 6000 22600760 33600760 3681300FM 3681400FM 3681500FM 3681600FM 3681700FM 3681800FM 3681900FM
2 3 4 6 8 10 12 14 16
k k a a a a a a a
2 3 4
k k a
FM Approvals
1-535
Product Designation
Remarks
6 8 10 12 14 16
a a a a a a
332
12 (175)
32
12 (175)
12 8 12 10
12 (175) 12 (175)
a a
4 6 8 10 12 14 16
a, c, f a, c, f a, c, f a, c, f a, c, f a, c, f a, c, f
14 (200)
24
14 (200)
24
14 (200)
Mitered Elbows, T14FM 9039859 HH9L11J89 9039860 9039911 9039861 HH9L13J89 9039862 9039863 9039912 9039864 9039865 HH9L17J89 9039866
24 (0-10) 24 (1015) 24 (15-20) 24 (20-22.5) 24 (22.5-25) 24 (25-30) 24 (30-35) 24 (35-40) 24 (40-45) 24 (45-50) 24 (50-55) 24 (55-60) 24 (60-65)
14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200) 14 (200)
k k k k k k k k k k k k k
FM Approvals
1-536
Product Designation
Remarks
k k k k k
24
14 (200)
24 24 12 24 24 14 24 24 16 24 24 18 24 24 20 24 24 22
k k k k k k
24
14 (200)
24
14 (200)
Pipe Bell Spigot Series 2416FM Key-Lock. 449M30A2 669M30A2 889M35A2 AA9M35A2 BB9M35A2 CC9M35B5 DD9M35B5 FF9M37B5
4 6 8 10 12 14 16 20
i i i i i i i i
Pipe Bell Spigot Series 2416FM Taper Taper 449M37G9 4 669M37G9 889M37G9 AA9M37G9 BB9M37G9 CC9M37G9 DD9M37G9 FF9M37G9 HH9M35G9 6 8 10 12 14 16 20 24
b, h b, h b, h b, h b, h b, h b, h l k
4 6 8
c, d c, d c, d
FM Approvals
1-537
Product Designation
Remarks
10 12 14 16 20
c, d c, d c, d c, d d
90 Elbow T16FM 449M20J8 669M20J8 889M20J8 AA9M20J8 BB9M20J8 CC9M20J8 DD9M20J8 FF9M20J8
4 6 8 10 12 14 16 20
h h h h h h h k
10 14
16 (230) 16 (230)
Elbow 45 K16FM 449M14D4 669M14D4 889M14D4 AA9M14D4 BB9M14D4 CC9M20E5 DD9M20E5 FF9M14E15
4 6 8 10 12 14 16 20
c, d c, d c, d c, d c, d c, d c, d d
45 Elbow T16FM 449M14J8 669M14J8 889M14J8 AA9M14J8 BB9M14J8 CC9M14J8 DD9M14J8 FF9M14J8
4 6 8 10 12 14 16 20
h h h h h h h k
14
16 (230)
Elbow 30 T16FM
FM Approvals
1-538
Product Designation
Remarks
TCC9M13J8
14
16 (230)
14
16 (230)
14
16 (230)
12 14
16 (230) 16 (230)
Elbow 15 T16FM TBB9M11J8 TCC9M11J8 Equal Tee K16FM 449M80D4 669M80D4 889M80D4 AA9M80D4 BB9M80D4 CC9M80E5 DD9M80E5 FF9M80E5
12 14
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) c, d c, d c, d c, d c, d c, d c, d d
4 6 8 10 12 14 16 20
Equal Tee T16FM 449M80J8 669M80J8 889M80J8 AA9M80J8 BB9M80J8 CC9M80J8 DD9M80J8 FF9M80J8 HH9M80J8
4 6 8 10 12 14 16 20 24
h h h h h h h k k
Reducing Tees K16FM 649M83D4 849M83D4 869M83D4 A49M83D4 A69M83D4 A89M83D4 B49M83D4 B69M83D4 B89M83D4 BA9M83D4 C69M83D3
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d
FM Approvals
1-539
Product Designation
Remarks
C89M83D3 CA9M83D3 CB9M83D3 D69M83D3 D89M83D3 DA9M83D3 DB9M83D3 DC9M83E5 F69M83EJ8 F89M83E5 F69M83EJ8 FB9M83E5 FC9M83E5 FD9M83E5
14 14 8 14 14 10 14 14 12 16 16 6 16 16 8 16 16 10 16 16 12 16 16 14 20 20 6 20 20 8 20 20 10 20 20 12 20 20 14 20 20 16
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
c, d c, d c, d c, d c, d c, d c, d c, d d d d d d d
Reducing Tee T16FM 649M83J8 849M83J8 869M83J8 A49M83J8 A69M83J8 A89M83J8 B49M83J8 B69M83J8 B89M83J8 BA9M83J8 C69M83J8 C89M83J8 CA9M83J8 CB9M83J8 D69M83J8 D89M83J8 DA9M83J8 DB9M83J8 DC9M83J8 F49M83J8 F69M86J8 F89M83J8 FA9M83J8 FB9M83J8 FC9M83J8 FD9M83J8 HB9M83J8
64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 14 6 14 8 14 10 14 12 16 6 16 8 16 10 16 12 16 14 20 20 4 20 20 6 20 20 8 20 20 10 20 20 12 20 20 14 20 20 16 24 24 12
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
a, h a, h h a, h h h a, h h h h h h h h h h h h h k k k k k k k k
FM Approvals
1-540
Product Designation
Remarks
24 24 14 24 24 16 24 24 18 24 24 20 24 24 22
k k k k k
Reducer T16FM 649M76J8 849M76J8 869M76J8 A69M76J8 A89M76J8 B89M76J8 BA9M76J8 CA9M76J8 CB9M76J8 DB9M76J8 DC9M76J8
64 84 86 10 6 10 8 12 8 12 10 14 10 14 12 16 12 16 14
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
a, h a, h h h h h h h h h h
Flange, Class 150 T16FM 449M53J8A 669M53J8A 889M53J8A AA9M53J8A BB9M53J8A CC9M53J8A DD9M53J8A HH9M53J8A
4 6 8 10 12 14 16 24
a h h h h h h k
24
16 (230)
Coupling T16FM 449M07J8 669M07J8 889M07J8 AA9M07J8 BB9M07J8 CC9M07J8 DD9M07J8 FF9M07E5
4 6 8 10 12 14 16 20
h h h h h h h d
Adapters TK16FM Key Lock Male Taper Male 229603A6 339603A6 449M03A6
2 3 4
e, h e, h e, h
FM Approvals
1-541
Product Designation
Remarks
6 8 10 12 14 16 20
e, h e, h e, h e, h e, h e, h k
Adapters TK16FM Key Lock Male Taper Female 229M03A5 2 339M03A5 449M03A5 669M03A5 889M03A5 AA9M03A5 BB9M03A5 CC9M03A5 DD9M03A5 FF9M03B8 3 4 6 8 10 12 14 16 20
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230)
e, h e, h e, h e, h e, h e, h e, h e, h e, h k
Pipe Bell & Spigot Series 2420FM Key-Lock. 449N30A2 669N30A2 AA9N35B5 BB9N35B5 CC9N35B5 DD9N35B5
4 6 10 12 14 16
i i i i i i
Pipe Series 2420FM Taper Taper 229N37G9 339N37G9 449N37G9 669N37G9 889N37G9 AA9N37G9 BB9N37G9 CC9N37G9 DD9N37G9
2 3 4 6 8 10 12 14 16
a, b a, b a, b a, b a, b a, b a, b a, b a, b
4 6 8 10 12 14
c, d c, d c, d c, d c, d c, d
FM Approvals
1-542
Product Designation
Remarks
DD9N20E5
16
20 (290)
c, d
2 3 4 6 8 10 12
h h h h h h h
4 6 8 10 12 14 16
c, d c, d c, d c, d c, d c, d c, d
2 3 4 6 8 10 12
h h h h h h h
Equal Tee K20FM 449N80D4 669N80D4 889N80D4 AA9N80E5 BB9N80E5 CC9N80E5 DD9N80E5
4 6 8 10 12 14 16
c, d c, d c, d c, d c, d c, d c, d
Equal Tee T20FM 229N80J8 339N80J8 449N80J8 669N80J8 889N80J8 AA9N80J8 BB9N80J8
2 3 4 6 8 10 12
h h h h h h h
FM Approvals
1-543
Product Designation
Remarks
649N83D4 849N83D4 869N83D4 A49N83D3 A69N83D3 A89N83D3 B49N83D3 B69N83D3 B89N83D3 BAN83E5 C69N83D3 C89N83D3 CA9N83E5 CB9N83E5 D69N83D3 D89N83D3 DA9N83E5 DB9N83E5 DC9N83E5
64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 14 6 14 8 14 10 14 12 16 6 16 8 16 10 16 12 16 14
20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290)
c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d c, d
Reducing Tee T20FM 329N83J8 429N83J8 439N83J8 629N83J8 639N83J8 649N83J8 839N83J8 849N83J8 869N83J8 A49N83J8 A69N83J8 A89N83J8 B49N83J8 B69N83J8 B89N83J8 BA9N83J8
32 42 43 62 63 64 83 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10
20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290)
h h h h h h h h h h h h h h h h
32 42 43 63 64
h h h h h
FM Approvals
1-544
Product Designation
Remarks
849N76J8 869N76J8 A69N76J8 A89N76J8 B89N76J8 BA9N76J8 CA9N76J8 CB9N76J8 DB9N76J8 DC9N76J8
84 86 10 6 10 8 12 8 12 10 14 10 14 12 16 12 16 14
20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290)
h h h h h h h h h h
Coupling T20FM 229N07J8 339N07J8 449N07J8 669N07J8 889N07J8 AA9N07J8 BB9N07J8 CC9N07J8 DD9N07J8
2 3 4 6 8 10 12 14 16
h h h h h h h h h
Flange, Class 150 T20FM 229N07J8A 339N07J8A 449N07J8A 669N07J8A 889N07J8A AA9N07J8A BB9N07J8A CC9N07J8A DD9N07J8A
2 3 4 6 8 10 12 14 16
h h h h h h h h h
2 3
40 (580) 40 (580)
k k
40 (580)
40 (580)
40 (580)
332
40 (580)
FM Approvals
1-545
Product Designation
Remarks
Blind Flange 20 Bar 22945700A 33945700A 44945700A 66945700A 88945700A AA945700A BB945700A CC945700A DD945700A
Remarks:
2 3 4 6 8 10 12 14 16
j j j j j j j j j
a. Bonded joints made with RP-34 adhesive. b. Spigot end of pipe must be prepared with Ameron equipment. See manufacturers instructions. c. Fittings for use with Key-Lock pipe. d. Fittings with Key-Lock female ends. e. Fittings with Key-Lock male ends. f. Flange to be bonded to Key-Lock male end adapter. g. Key-Lock male end adapter to be bonded to flange. h. Bonded joints made with RP-48 adhesive. i. Pipe KLM KLF - rubber O-ring mechanical lock joint. j. Parts are molded.
Amiantit Epoxy Pipe Production Plant (Amipox), Box 589, First Industrial City, Dammam 31421, Kingdom of Saudi Arabia
Identification Size mm (in.) Pressure Rating bar (psi) Remarks
AT-12 Series Pipe 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) ASL-12 Series Pipe with Seal-Lock Joints 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) AT-12 Series 90 Elbows 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) AT-12 Series 45 Elbows 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) b, c b, c b, c b, c b, c 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) a, d a, d a, d a, d a, d a, d a, d
FM Approvals
1-546
Identification
Size mm (in.)
Remarks
100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) AT-12 Series Equal Tees 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) Flange with Socket End, Bolting Flange, ANSI B16.5, Class 150 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16)
a. b. c. d. Bonded joints made with RP-48 or Araldite AV4738 adhesive. Joints made with O-Ring seal and locking key. Standard Taper Flange. Taper taper adhesive joint.
a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d
a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d a, c, d
c c c c c c c
Amiantit Fiberglass Industries Ltd, Box 589, Dammam 31421 Kingdom of Saudi Arabi
Product Designation Nominal Pipe Size, mm Pressure Rating, bar (psi)
Pipe AF/FM/2200-1 AF/FM/2200-2 AF/FM/2200-3 AF/FM/2200-4 AF/FM-2200-5 AF/FM/2200-6 AF/FM/2200-7 AF/FM/2200-8 AF/FM/2200-9 AF/FM/2200-10 AF/FM/2200-11 AF/FM/2200-12 AF/FM/2200-13
750 700 600 500 450 400 350 300 700 600 500 450 400
12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 15 (220) 15 (220) 15 (220) 15 (220) 15 (220)
FM Approvals
1-547
Product Designation
AF/FM/2200-14 AF/FM/2200-15 Butt Strap Joint AF/FM/2304-1 AF/FM/2304-2 AF/FM/2304-3 AF/FM/2304-4 AF/FM/2304-5 AF/FM/2304-6 AF/FM/2304-7 AF/FM/2304-8 AF/FM/2304-9 AF/FM/2304-10 AF/FM/2304-11 AF/FM/2304-12 AF/FM/2304-13 AF/FM/2304-14 AF/FM/2304-15 Coupling AF/FM/2600-01 AF/FM/2600-02 AF/FM/2600-03 AF/FM/2600-04 AF/FM/2600-05 AF/FM/2600-06 AF/FM/2600-07 AF/FM/2600-08 AF/FM/2600-09 AF/FM/2600-10 AF/FM/2600-11 AF/FM/2600-12 AF/FM/2600-13 AF/FM/2600-14 AF/FM/2600-15 30 Elbow AF/FM/2301-1 AF/FM/2301-2 AF/FM/2301-3 AF/FM/2301-4 AF/FM/2301-5 AF/FM/2301-6 AF/FM/2301-7 AF/FM/2301-8 45 Elbow
350 300
15 (220) 15 (220) 12 (175) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 15 (220) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 15 (220) 15 (220) 15 (220) 15 (220) 15 (220) 15 (220) 15 (220) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175)
750 700 700 600 600 500 500 450 450 400 400 350 350 300 300
750 700 600 500 450 400 350 300 700 600 500 450 400 350 300
FM Approvals
1-548
Product Designation
AF/FM/2301-9 AF/FM/2301-10 AF/FM/2301-11 AF/FM/2301-12 AF/FM/2301-13 AF/FM/2301-14 AF/FM/2301-15 AF/FM/2301-16 90 Elbow AF/FM/2301-17 AF/FM/2301-18 AF/FM/2301-19 AF/FM/2301-20 AF/FM/2301-21 AF/FM/2301-22 AF/FM/2301-23 AF/FM/2301-24 Blind Flange AF/FM/2309-1 AF/FM/2309-2 AF/FM/2309-3 AF/FM/2309-4 AF/FM/2309-5 AF/FM/2309-6 AF/FM/2309-7 Eccentric Reducer AF/FM/2306-1 AF/FM/2306-2 AF/FM/2306-3 AF/FM/2306-4 AF/FM/2306-5 AF/FM/2306-6 AF/FM/2306-7 AF/FM/2306-8 AF/FM/2306-9 AF/FM/2306-10 AF/FM/2306-11 AF/FM/2306-12 AF/FM/2306-13 AF/FM/2306-14 AF/FM/2306-15 AF/FM/2306-16 AF/FM/2306-17 AF/FM/2306-18
12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175)
750 700 750 600 750 500 750 450 750 400 750 350 750 300 750 200 750 150 750 50 700 600 700 500 700 450 700 400 700 350 700 300 600 500 600 450
FM Approvals
1-549
Product Designation
AF/FM/2306-19 AF/FM/2306-20 AF/FM/2306-21 AF/FM/2306-22 AF/FM/2306-23 AF/FM/2306-24 AF/FM/2306-25 AF/FM/2306-26 AF/FM/2306-27 AF/FM/2306-28 AF/FM/2306-29 AF/FM/2306-30 AF/FM/2306-31 AF/FM/2306-32 AF/FM/2306-33 AF/FM/2306-34 AF/FM/2306-35 AF/FM/2306-36 AF/FM/2306-37 AF/FM/2306-38 AF/FM/2306-39 AF/FM/2306-40 AF/FM/2306-41 AF/FM/2306-42 AF/FM/2306-43 Tee AF/FM/2302-1 AF/FM/2302-2 AF/FM/2302-3 AF/FM/2302-4 AF/FM/2302-5 AF/FM/2302-6 AF/FM/2302-7 AF/FM/2302-8 AF/FM/2302-9 AF/FM/2302-10 AF/FM/2302-11 AF/FM/2302-12 AF/FM/2302-13 AF/FM/2302-14 AF/FM/2302-15 AF/FM/2302-16 AF/FM/2302-17
600 400 600 350 600 300 500 450 500 400 500 350 500 300 500 250 500 150 500 75 450 400 450 350 450 300 450 200 450 75 400 350 400 300 400 200 350 300 350 250 350 200 350 75 300 250 300 100 300 50
12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150) 12 (175) 12 (175) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150)
750 750 750 450 750 350 750 300 750 250 750 200 750 150 600 600 600 450 600 350 600 300 600 250 600 200 600 150 500 500 500 450 500 350
FM Approvals
1-550
Product Designation
AF/FM/2302-18 AF/FM/2302-19 AF/FM/2302-20 AF/FM/2302-21 AF/FM/2302-22 AF/FM/2302-23 AF/FM/2302-24 AF/FM/2302-25 AF/FM/2302-26 AF/FM/2302-27 AF/FM/2302-28 AF/FM/2302-29 AF/FM/2302-30 AF/FM/2302-31 AF/FM/2302-32 AF/FM/2302-33 AF/FM/2302-34 AF/FM/2302-35 AF/FM/2302-36 AF/FM/2302-37 AF/FM/2302-38 AF/FM/2302-39 AF/FM/2302-40 AF/FM/2302-41 AF/FM/2302-42 AF/FM/2302-43 AF/FM/2302-44 AF/FM/2302-45 AF/FM/2302-46
500 300 500 250 500 200 500 150 500 75 450 450 450 350 450 300 450 250 450 200 450 150 450 75 400 400 400 350 400 300 400 250 400 200 400 150 350 350 350 300 350 250 350 200 350 150 350 75 300 300 300 250 300 200 300 150 300 50
10.5 (150) 12 (175) 12 (175) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 12 (175) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150) 10.5 (150) 12 (175) 12 (175) 10.5 (150) 10.5 (150) 10.5 (150) 12 (175) 12 (175)
Flange AF/FM/2307-1 AF/FM/2307-2 AF/FM/2307-3 AF/FM/2307-4 AF/FM/2307-5 AF/FM/2307-6 AF/FM/2307-7 AF/FM/2307-8 AF/FM/2307-9 AF/FM/2307-10 AF/FM/2307-11 AF/FM/2307-12
750 600 500 450 400 356 300 750 600 500 450 400
12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 12 (175) 15 (220) 15 (220) 15 (220) 15 (220) 15 (220)
FM Approvals
1-551
Product Designation
AF/FM/2307-13 AF/FM/2307-14
356 300
15 (220) 15 (220)
Bondstrand Series 6000 Pipe. D36793 D36794 D36795 D36796 D36798 D36799 D36800 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) * * * * * * * a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c a, b, c
Bondstrand Series 6000 Fittings 90 Elbow, 45 Elbow, Equal Tees, 45Lateral 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) * a, b, d
a, b, i
Bondstrand Series 2212 Pipe. D30563 D30564 D36982 D36983 D36977 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) * * * * *
FM Approvals
1-552
Product Designation
Remarks
14 (350) 16 (400) 18 (450) 20 (500) 24 (600) Bondstrand Series 2414 Pipe 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) Bondstrand Series 2416 Pipe 4 (100) 16 (400) Bondstrand Series 2416 Pipe 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) Key-Lock Ends 90 Elbow, 45 Elbow, Equal Tees, 45Lateral 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600)
* * * * *
e, f, g e, f, g e, f, g e, f, g e, f, g
e, f, g, h, j, k, l e, f, g, h, j, k, l e, f, g, h, j, k, l e, f, g, h, j, k, l e, f, g, h, j, k, l e, f, g, h, j, k, l e, f, g, h, j, k, l
16 (232) 16 (232)
e, f, g, h, j, k, l e, f, g, h, j, k, l
g, k g, k g, k g, k g, k
FM Approvals
1-553
Product Designation
Remarks
Coupling
Key-Lock Adapter
Concentric Reducer
4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) 2 x 4 in. through 14 x 16 in. (14 sizes)
Female Tapered Socket 90 Elbow, 45 Elbow, Equal Tees, 45Lateral Coupling 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) * k
FM Approvals
1-554
Product Designation
Remarks
4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600)
b, k
Series 2414 Fittings All Female Taper Ends 45 Elbow 90 Elbow Equal Tee 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) 14 (203) b, g, k b, g, k b, g, k b, g, k b, g, k
Flat Face Flange. Dimensions to fit with ANSI B16.5, Class 150 Flanges.
b, g, k b, g, k b, g, k b, g, k b, g, k b, g, k b, g, k
Series 2416 Fittings All Female Taper Ends 45 Elbow 90 Elbow Equal Tee 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) b, g, k b, g, k b, g, k b, g, k b, g, k
Flat Face Flange. Dimensions to fit with ANSI B16.5, Class 150 Flanges.
b, g, k b, g, k b, g, k b, g, k b, g, k b, g, k b, g, k
FM Approvals
1-555
Product Designation
Remarks
45 Elbow 90 Elbow Equal Tee Flat Face Flange. Dimensions to fit with ANSI B16.5, Class 300 Flanges.
4 (100)
20 (290)
b, g, k
6 (150)
20 (290)
b, g, k
*12 bar (175 psi) a. Bonded joints made with RP-34 adhesive. b. Spigot end of pipe must be prepared with Bondstrand Ltd equipment. See manufacturers instructions. c. Pipes equipped with one bell and one spigot end. Pipe lengths joined by Quick-Lock bell and spigot joints. d. Fittings are furnished with bell ends for Quick-Lock adhesive joint with spigot end pipe. e. Key-lock coupling joint. f. Key-lock integral female joint. g. Tapertaper adhesive joint. h. Furnished with Key-Lock male ends for a mechanical joint. i. Flange hub furnished with bell for Quick-Lock adhesive joint with spigot end pipe. j. Furnished with Key-Lock female ends for a mechanical joint. k. Furnished with tapered female socket for RP-48 or FPI-44 epoxy adhesive joint. l. Furnished with Key-Lock male mechanical joint on one end by taper adhesive (male or female) joint on the other end.
Composite Pipes Industry L.L.C., Post Box 30, Postal Code 327, Sohar Industrial Estate, Sohar, Sultanate of Oman
Identification Size, mm Pressure Rating bar (psi) Remarks
16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232)
a, b a, b a, b a, b a, b a, b
90 Elbows
a a a a a a
45 Elbows
a a a a a a
Equal Tees
a a a a a a
Unequal Tee
a a
FM Approvals
1-556
Identification
Size, mm
Remarks
100 100 80 150 150 50 150 150 80 150 150 100 150 150 125 200 200 80 200 200 100
16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232)
a a a a a a a
Unequal Tee
200 200 150 250 250 100 250 250 150 250 250 200 300 300 100 300 300 150 300 300 200 300 300 250 400 400 150 400 400 200 400 400 250 400 400 300 400 400 350
a a a a a a a a a a a a a
Flange with Socket End, Bolting Flange, ANSI B16.5, Class 150
Blind Flange
a. Joined by Araldite AV4738/HV4739 adhesive, Epoxy based glue RP48 and Vantico AV4415/HV4416. b. Spigot end of pipe must be prepared with equipments provided by Composite Pipes Industry L.L.C. See manufacturers instructions.
Fiberglass Pipe Co Ltd, Dammam, Second Industrial City, Box 589, Dammam, 31421, Kingdom of Saudi Arabia
Identification Size, mm (in.) Pressure Rating bar (psi) Remarks
Pipe (PC12)
FM Approvals
1-557
Identification
Size, mm (in.)
Remarks
12 (175) 12 (175)
Pipe (PC16)
150 (6) 250 (10) 350 (14) 400 (16) 450 (18) 500 (20)
150 (6) 250 (10) 350 (14) 400 (16) 450 (18) 500 (20)
150 (6) 250 (10) 350 (14) 400 (16) 450 (18) 500 (20)
FM Approvals
1-558
Future Pipe Industries LLC, Mussafah Industrial Area, Box 29205, Mussafah, Abu Dhabi, United Arab Emirates
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa) Remarks
Pipe Plain Ends (for laminated joints) PL/PL PI-8 PI-9 PI-10 PI-11 PI-12 PI-13 PI-14 PI-15 200 250 300 350 400 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) a a a a a a a a
Pipe Spigot and Socket Ends (for cemented joints). CB/CS PII-8 PII-9 PII-10 PII-11 PII-12 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b
Pipe with Spigot & Socket Ends, TB/TS PIV-14 PIV-15 PIV-16 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) b b b
Pipe Spigot and Socket Ends for (O-Ring & Locking Strip joints). FB/FS PIII-8 PIII-9 PIII-10 PIII-11 PIII-12 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) c c c c c
Pipe-Plain Ends (for laminated joints) PL/PL PI-1 PI-2 PI-3 PI-4 PI-5 PI-6 PI-7 PI-16 PI-17 PI-18 100 150 200 250 300 350 400 450 500 600 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16 (232) 16 (232) 16 (232) a a a a a a a a a a
FM Approvals
1-559
Product Designation
Remarks
Pipe Spigot and Socket Ends (for cemented joints). CB/CS PII-1 PII-2 PII-3 PII-4 PII-5 PII-6 PII-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
Pipe with Spigot & Socket Ends, TB/TS PIV-11 PIV-12 PIV-13 450 500 600 16 (232) 16 (232) 16 (232) b b b
Pipe Spigot and Socket Ends (for O-Ring & Locking Strip joints). FB/FS PIII-1 PIII-2 PIII-3 PIII-4 PIII-5 PIII-6 PIII-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16 (232) 16.0 (232) 16.0 (232) c c c c c c c
Pipe with Plain Ends, PL/PL PIV-24 PIV-25 PIV-26 PIV-27 PIV-28 PIV-29 PIV-30 100 150 200 250 300 350 400 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) a a a a a a a
Pipe with Spigot and Socket Ends, TB/TS PIV-17 PIV-18 PIV-19 PIV-20 PIV-21 PIV-22 PIV-23 PIV-8 PIV-9 PIV-10 100 150 200 250 300 350 400 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b
FM Approvals
1-560
Product Designation
Remarks
90 Elbow with Plain Ends, PL/PL EL 17 EL 18 EL 19 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) a a a
90 Elbows Socket Ends (for cemented joints) CB/CB EL90-8 EL90-9 EL90-10 EL90-11 EL90-12 EL90-13 150 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
90 Elbow, TB/TS EL90-27 EL90-28 EL90-29 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) b b b
90 Elbows Socket Ends (for cemented joints) CB/CB EL90-1 EL90-2 EL90-3 EL90-4 EL90-5 EL90-6 EL90-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
90 Elbow, TB/TS EL90-24 EL90-25 EL90-26 450 500 600 16 (232) 16 (232) 16 (232) b b b
90 Elbow, TB/TB EL90-30 EL90-31 EL90-32 EL90-33 EL90-34 EL90-35 EL90-36 100 150 200 250 300 350 400 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b
FM Approvals
1-561
Product Designation
Remarks
EL90-22 EL90-23
500 600
20 (290) 20 (290)
b b
45 Elbow with Plain Ends, PL/PL EL 14 EL 15 EL 16 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) a a a
45 Elbows Socket Ends (for cemented joints)CB/CB EL45-8 EL45-9 EL45-10 EL45-11 EL45-12 EL45-13 150 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
45 Elbow, TB/TS EL45-27 EL45-28 EL45-29 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) b b b
45 Elbows Socket Ends (for cemented joints) CB/CB EL45-1 EL45-2 EL45-3 EL45-4 EL45-5 EL45-6 EL45-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
45 Elbow, TB/TS EL45-24 EL45-25 EL45-26 450 500 600 16 (232) 16 (232) 16 (232) b b b
45 Elbow, TB/TB EL45-30 EL45-31 EL45-32 EL45-33 EL45-34 EL45-35 EL45-36 100 150 200 250 300 350 400 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b
FM Approvals
1-562
Product Designation
Remarks
45 Elbow, TB/TS EL45-21 EL45-22 EL45-23 450 500 600 20 (290) 20 (290) 20 (290) b b b
Equal Tee Socket Ends (for cemented joints) CB/CB/CB ET-8 ET-9 ET-10 ET-11 ET-12 ET-13 150 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
Equal Tee, TB/TS-TB ET-27 ET-28 ET-29 ET-27-C ET-28-C ET-29-C 450 500 600 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
Equal Tee with Plain Ends, PL/PL-PL ET 14 ET 15 ET 16 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) a a a
Equal Tees Socket Ends (for cemented joints). CB/CB/CB ET-1 ET-2 ET-3 ET-4 ET-5 ET-6 ET-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
Equal Tee, TB/TS-TB ET-24 ET-25 ET-26 ET-24-C ET-25-C ET-26-C 450 500 600 450 500 600 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) b b b b b b
FM Approvals
1-563
Product Designation
Remarks
b b b b b b b
Equal Tee, TB/TS-TB ET-21 ET-22 ET-23 ET-21-C ET-22-C ET-23-C 450 500 600 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b
Unequal Tees Socket Ends (for cemented joints) CB/CB/CB UT-8/B UT-9/B UT-9/C UT-10/B UT-10/C UT-10/D UT-11/B UT-11/C UT-11/D UT-11/E UT-12/B UT-12/C UT-12/D UT-12/E UT-12/F UT-13/B UT-13/C UT-13/D UT-13/E UT-13/F UT-13/G 150 100 200 100 200 150 250 100 250 150 250 200 300 100 300 150 300 200 300 250 350 100 350 150 350 200 350 250 350 300 400 100 400 150 400 200 400 250 400 300 400 350 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b b b b b b b b b b b
Unequal Tee with Plain Ends PL/PL/PL UT-39 UT-40 UT-41 450x200 450x250 450x300 12.5 (180) 12.5 (180) 12.5 (180) a a a
FM Approvals
1-564
Product Designation
Remarks
UT-42 UT-43 UT-44 UT-45 UT-46 UT-47 UT-48 UT-49 UT-50 UT-51 UT-52 UT-53 UT-54 UT-55 UT-56
450x350 450x400 500x200 500x250 500x300 500x350 500x400 500x450 600x200 600x250 600x300 600x350 600x400 600x450 600x500
12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
a a a a a a a a a a a a a a a
Unequal Tee, TB/TS-TB UT-21/N UT-21/O UT-21/P UT-21/N-C UT-21/O-C UT-21/P-C 500x450 600x450 600x500 500x450 600x450 600x500 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
Unequal Tees Socket Ends (for cemented joints) CB/CB/CB UT-2/B UT-3/B UT-3/C UT-4/B UT-4/C UT-4/D UT-5/B UT-5/C UT-5/D UT-5/E UT-6/B UT-6/C UT-6/D UT-6/E UT-6/F UT-7/B UT-7/C UT-7/D 150 100 200 100 200 150 250 100 250 150 250 200 300 100 300 150 300 200 300 250 350 100 350 150 350 200 350 250 350 300 400 100 400 150 400 200 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b b b b b b b b b b b b
FM Approvals
1-565
Product Designation
Remarks
b b b
Unequal Tee, TB/TS-TB UT-21/K UT-21/L UT-21/M UT-21/K-C UT-21/L-C UT-21/M-C 500x450 600x450 600x500 500x450 600x450 600x500 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) b b b b b b
Unequal Tee, TB/TB-TB UT-22/H UT-23/H UT-23/I UT-24/H UT-24/I UT-24/J UT-25/H UT-25/I UT-25/J UT-25/K UT-26/H UT-26/I UT-26/J UT-26/K UT-26/L UT-27/H UT-27/I UT-27/J UT-27/K UT-27/L UT-27/M 150x100 200x100 200x150 250x100 250x150 250x200 300x100 300x150 300x200 300x250 350x100 350x150 350x200 350x250 350x300 400x100 400x150 400x200 400x250 400x300 400x350 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b b b b b b b b b b b b
Unequal Tee, TB/TS-TB UT-21/H UT-21/I UT-21/J UT-21/H-C UT-21/I-C UT-21/J-C 500x450 600x450 600x500 500X450 600x450 600x500 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b
FM Approvals
1-566
Product Designation
Remarks
12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
a a a a a a a a a
Concentric Reducers Socket Ends (for cemented joints). CB/CB CR-8/B CR-9/A CR-9/B CR-10/A CR-10/B CR-11/A CR-11/B CR-12/A CR-12/B CR-13/A CR-13/B 150 100 200 100 200 150 250 150 250 200 300 200 300 250 350 250 350 300 400 300 400 350 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b
Concentric Reducer, TB/TS CR-23/A-C CR-26/A-C CR-29/A-C 500x450 600x450 600x500 12.5 (180) 12.5 (180) 12.5 (180) b b b
Concentric Reducers Socket Ends (for cemented joints). CB/CB CR-2/B CR-3/A CR-3/B CR-4/A CR-4/B CR-5/A CR-5/B CR-6/A CR-6/B CR-7/A CR-7/B 150 100 200 100 200 150 250 150 250 200 300 200 300 250 350 250 350 300 400 300 400 350 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b b b b b
FM Approvals
1-567
Product Designation
Remarks
b b b
Concentric Reducer, TB/TB CR-30 CR-31 CR-32 CR-33 CR-34 CR-35 CR-36 CR-37 CR-38 CR-39 CR-40 150x100 200x100 200x150 250x150 250x200 300x200 300x250 350x250 350x300 400x300 400x350 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b b
Concentric Reducer, TB/TS CR-21/A-C CR-24/A-C CR-27/A-C 500x450 600x450 600x500 20 (290) 20 (290) 20 (290) b b b
Eccentric Reducer, TB/TB ER-1 ER-2 ER-3 ER-4 ER-5 ER-6 ER-7 ER-8 ER-9 ER-10 ER-11 150x100 200x100 200x150 250x150 250x200 300x200 300x250 350x250 350x300 400x300 400x350 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b b
Adaptor Spigot Ends (for cemented joints) CS/CS AdapI-8 AdapI-9 AdapI-10 AdapI-11 AdapI-12 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b
Adaptor, TS/TS
FM Approvals
1-568
Product Designation
Remarks
b b b
Adaptor Spigot Ends (for cemented joints) CS/CS AdapI-1 AdapI-2 AdapI-3 AdapI-4 AdapI-5 AdapI-6 AdapI-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
Adaptor, TS/TS Adap 4-11 Adap 4-12 Adap 4-13 450 500 600 16 (232) 16 (232) 16 (232) b b b
Adaptor, TS/TS Adap 4-17 Adap 4-18 Adap 4-19 Adap 4-20 Adap 4-21 Adap 4-22 Adap 4-23 Adap 4-8 Adap 4-9 Adap 4-10 100 150 200 250 300 350 400 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b
Coupler Socket Ends (for cemented joints) CB/CB CplrI-8 CplrI-9 CplrI-10 CplrI-11 CplrI-12 CplrI-13 150 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b
Coupler, TB/TB Cplr 4-14 Cplr 4-15 Cplr 4-16 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) b b b
FM Approvals
1-569
Product Designation
Remarks
Coupler Socket Ends (for cemented joints) CB/CB CplrI-1 CplrI-2 CplrI-3 CplrI-4 CplrI-5 CplrI-6 CplrI-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
Coupler, TB/TB Cplr 4-11 Cplr 4-12 Cplr 4-13 450 500 600 16 (232) 16 (232) 16 (232) b b b
Coupler, TB/TB Cplr 4-17 Cplr 4-18 Cplr 4-19 Cplr 4-20 Cplr 4-21 Cplr 4-22 Cplr 4-23 Cplr 4-8 Cplr 4-9 Cplr 4-10 100 150 200 250 300 350 400 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b
Flange with Socket End (for cemented joints) CB/FL F-8 F-9 F-10 F-11 F-12 Flange with Socket End TB/FF F-26 F-27 F-28 F-26-C F-27-C F-28-C 450 500 600 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b 200 250 300 350 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b
FM Approvals
1-570
Product Designation
Remarks
FL 2 FL 3
500 600
a a
Flange with Socket End (for cemented joints) CB/FL F-1 F-2 F-3 F-4 F-5 F-6 F-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b
Flange with Socket End, TB/FF F-23 F-24 F-25 F-23-C F-24-C F-25-C 450 500 600 450 500 600 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) b b b b b b
Flange with Socket End, TB/FF F-29 F-30 F-31 F-32 F-33 F-34 F-35 F-20 F-21 F-22 F-20-C F-21-C F-22-C 100 150 200 250 300 350 400 450 500 600 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) b b b b b b b b b b b b b
Blind Flange, FL BF-8 BF-9 BF-10 BF-11 BF-12 BF 15 BF 16 200 250 300 350 400 450 500 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
FM Approvals
1-571
Product Designation
Remarks
BF 17
600
12.5 (180)
Blind Flange, FL BF-26 BF-27 BF-28 450 500 600 12.5 (180) 12.5 (180) 12.5 (180) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232) 16 (232)
BF-1 BF-2 BF-3 BF-4 BF-5 BF-6 BF-7 BF-23 BF-24 BF-25
100 150 200 250 300 350 400 450 500 600
Blind Flange, FL BF-29 BF-30 BF-31 BF-32 BF-33 BF-34 BF-35 BF-20 BF-21 BF-22 100 150 200 250 300 350 400 450 500 600 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290) 20 (290)
Saddle with Nipple SaN-1 SaN-2 SaN-3 SaN-4 SaN-5 SaN-6 SaN-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b, d b, d b, d b, d b, d b, d b, d
Saddle with Nipple SdN-01 SdN-02 SdN-03 SdN-04 100 150 200 250 20 (290) 20 (290) 20 (290) 20 (290) b, e b, e b, e b, e
FM Approvals
1-572
Product Designation
Remarks
b, e b, e b, e
Reducing Saddle with Plain End, PL RS 1 RS 2 RS 3 RS 4 RS 5 RS 6 450x100 450x150 500x100 500x150 600x100 600x150 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) a/b a/b a/b a/b a/b a/b
Reducing Saddle with Spigot End (for cemented joints) RS-4/E RS-5/E RS-6/E 300 100 350 100 400 100 16.0 (232) 16.0 (232) 16.0 (232) b b b
Straight Butt Wrap Lamination Details LAM-1 LAM-2 LAM-3 EPI/FM/L/01 Sh2 R3 EPI/FM/L/01 Sh1 R3 450 500 600 100 to 400 100 to 400 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 16.0 (232) a a a a a
Straight Butt Wrap Lamination Details SLAM-01 SLAM-02 SLAM-03 SLAM-04 SLAM-05 SLAM-06 SLAM-07
a. b. c. d. e. Pipe lengths joined with Butt Wrap joint. Joined by Easy Fit Wavistrong Adhesive. Joints made with O-Ring seal and locking device. Available with 14, 12, 34 and 1 in. nipple. Available with 14, 12 and 34 nipple.
a a a a a a a
Future Pipe Industries (SAE), Industrial Zone 5, Box 96, Postal Zone 12573, 6th of October City, Egypt
Product Designation Nominal Pipe Size, mm Pressure Rating* Remarks
Plain End (Laminated Joint) System Pipe PI-1 PI-2 PI-3 PI-4 PI-5 PI-6 PI-7 PI-8 PI-9
m, f m, f m, f m, f m, f m, h m, h m, h m, h
FM Approvals
1-573
Product Designation
Pressure Rating*
Remarks
PI-10 PI-11 PI-12 PI-13 PI-14 PI-15 PI-16 PI-17 PI-18 PI-19 PI-20 Butt Wrapped (Laminate Joint) System BW-11 BW-12 BW-13 BW-14 BW-15 BW-16 BW-17 BW-18 BW-19 BW-20 BW-01 BW-02 BW-03 BW-04 BW-05 BW-06 BW-07 BW-08 BW-09 BW-10 90 Elbow Plain End System ELP-9 ELP-10 ELP-11 ELP-12 ELP-13 ELP-14 ELP-15 ELP-16 45 Elbow Plain End System ELP-1 ELP-2 ELP-3 ELP-4 ELP-5 ELP-6 ELP-7 ELP-8 Equal Tee Plain End System ETP-1 ETP-2 ETP-3 ETP-4 ETP-5 ETP-6 ETP-7 ETP-8 Unequal Tee Plain End System UTP-1 UTP-2 UTP-3 UTP-4 UTP-5 UTP-6 UTP-7 UTP-8 UTP-9 UTP-10 UTP-11
500 600 200 250 300 300 350 400 450 500 600
EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
m, h m, h m, f m, f m, f m, h m, h m, h m, h m, h m, h
100 150 200 250 300 350 400 450 500 600 100 150 200 250 300 350 400 450 500 600
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST25/FM12.5 EST20/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
m m m m m m m m m m m m m m m m m m m m
m m m m m m m m
m m m m m m m m
m m m m m m m m
400400100 400400150 400400200 400400250 400400300 400400350 450450100 450450150 450450200 450450250 450450300
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
m m m m m m m m m m m
FM Approvals
1-574
Product Designation
Pressure Rating*
Remarks
UTP-12 UTP-13 UTP-14 UTP-15 UTP-16 UTP-17 UTP-18 UTP-19 UTP-20 UTP-21 UTP-22 UTP-23 UTP-24 UTP-25 UTP-26 UTP-27 UTP-28 UTP-29 UTP-30 UTP-31 UTP-32 UTP-33 UTP-34 UTP-35 UTP-36 UTP-37 UTP-38 UTP-39 UTP-40 UTP-41 UTP-42 UTP-43 UTP-44 UTP-45 UTP-46 UTP-47 UTP-48 UTP-49 UTP-50 UTP-51 UTP-52 UTP-53 UTP-54 UTP-55 UTP-56 UTP-57 UTP-58 UTP-59 UTP-60 Fittings Flange Plain End System FL-1 FL-2 FL-3 FL-4 FL-5 FL-6 FL-7 FL-8
450450350 450450400 500500100 500500150 500500200 500500250 500500300 500500350 500500400 500500450 600600100 600600150 600600200 600600250 600600300 600600350 600600400 600600450 600600500 400400100 400400150 400400200 400400250 400400300 400400350 450450100 450450150 450450200 450450250 450450300 450450350 450450400 500500100 500500150 500500200 500500250 500500300 500500350 500500400 500500450 600600100 600600150 600600200 600600250 600600300 600600350 600600400 600600450 600600500
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m
m m m m m m m m
CE (Cement Joint) Tapered Socket and Cylindrical Spigot System Pipe PII-1 100 PII-2 150 PII-3 200 PII-4 250 PII-5 300 PII-6 300 PII-7 350 PII-8 400 PII-9 200 PII-10 250 PII-11 300 PII-12 300 PII-13 350 PII-14 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
c, f c, f c, f c, f c, f c, h c, h c, h c, g c, g c, g c, h c, h c, h
FM Approvals
1-575
Product Designation
Pressure Rating*
Remarks
90 Elbow CE Joint System EL90-1 EL90-2 EL90-3 EL90-4 EL90-5 EL90-6 EL90-7 EL90-9 EL90-10 EL90-11 EL90-12 EL90-13 45 Elbow CE Joint System EL45-1 EL45-2 EL45-3 EL45-4 EL45-5 EL45-6 EL45-7 EL45-9 EL45-10 EL45-11 EL45-12 EL45-13 Equal Tee CE Joint System ET-1 ET-2 ET-3 ET-4 ET-5 ET-6 ET-7 ET-8 ET-9 ET-10 ET-11 ET-12 ET-13 Unequal Tee CE Joint System UT-2/B UT-3/B UT-3/C UT-4/B UT-4/C UT-4/D UT-5/B UT-5/C UT-5/D UT-5/E UT-6/B UT-6/C UT-6/D UT-6/E UT-6/F UT-7/B UT-7/C UT-7/D UT-7/E UT-7/F UT-7/G UT-9/B UT-9/C UT-10/B UT-10/C UT-10/D UT-11/B UT-11/C UT-11/D UT-11/E UT-12/B
100 150 200 250 300 350 400 200 250 300 350 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b
100 150 200 250 300 350 400 200 250 300 350 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b
100 150 200 250 300 350 400 150 200 250 300 350 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b b
150150100 200200100 200200150 250250100 250250150 250250200 300300100 300300150 300300200 300300250 350350100 350350150 350350200 350350250 350350300 400400100 400400150 400400200 400400250 400400300 400400350 200200100 200200150 250250100 250250150 250250200 300300100 300300150 300300200 300300250 350350100
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b
FM Approvals
1-576
Product Designation
Pressure Rating*
Remarks
UT-12/C UT-12/D UT-12/E UT-12/F UT-13/B UT-13/C UT-13/D UT-13/E UT-13/F UT-13/G Concentric Reducer CE Joint System CR-2/B CR-3/A CR-3/B CR-4/A CR-4/B CR-5/A CR-5/B CR-6/A CR-6/B CR-7/A CR-7/B CR-9/A CR-9/B CR-10/A CR-10/B CR-11/A CR-11/B CR-12/A CR-12/B CR-13A CR-13/B Eccentric Reducer CE Joint System ER-2/B ER-3/A ER-3/B ER-4/A ER-4/B ER-5/A ER-5/B ER-6/A ER-6/B ER-7/A ER-7/B ER-9/A ER-9/B ER-10/A ER-10/B ER-11/A ER-11/B ER-12/A ER-12/B ER-13/A ER-13/B Coupling CE Joint System CplrI-1 CplrI-2 CplrI-3 CplrI-4 CplrI-5 CplrI-6 CplrI-7 CplrI-8 CplrI-9 CplrI-10 CplrI-11 CplrI-12 CplrI-13 Adapter CE Joint System ADOPI-1 ADOPI-2 ADOPI-3
350350150 350350200 350350250 350350300 400400100 400400150 400400200 400400250 400400300 400400350
EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b
150100 200100 200150 250150 250200 300200 300250 350250 350300 400300 400350 200100 200150 250150 250200 300200 300250 350250 350300 400300 400350
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b b b b b b b b b b
150100 200100 200150 250150 250200 300200 300250 350250 350300 400300 400350 200100 200150 250150 250200 300200 300250 350250 350300 400300 400350
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b b b b b b b b b b
100 150 200 250 300 350 400 150 200 250 300 350 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b b
a a a
FM Approvals
1-577
Product Designation
Pressure Rating*
Remarks
ADOPI-4 ADOPI-5 ADOPI-6 ADOPI-7 ADOPI-8 ADOPI-9 ADOPI-10 ADOPI-11 ADOPI-12 Fittings Flange CE Joint System F-1 F-2 F-3 F-4 F-5 F-6 F-7 F-8 F-9 F-10 F-11 F-12 Fittings Blind Flange BF-1 BF-2 BF-3 BF-4 BF-5 BF-6 BF-7 BF-8 BF-9 BF-10 BF-11 BF-12 BF-13 BF-14 BF-15 BF-16 RSLJ (Rubber Seal Lock Joint) socket and spigot system Pipe PIII-1 PIII-2 PIII-3 PIII-4 PIII-5 PIII-6 PIII-7 PIII-8 PIII-9 PIII-10 PIII-11 PIII-12 PIII-13 PIII-14 PIII-15 PIII-16 PIII-17 PIII-18 PIII-19 PIII-20
a a a a a a a a a
100 150 200 250 300 350 400 200 250 300 350 400
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
b b b b b b b b b b b b
100 150 200 250 300 350 400 500 600 200 250 300 350 400 500 600
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
100 150 200 250 300 300 350 400 450 500 600 200 250 300 300 350 400 450 500 600
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
c, f c, f c, f c, f c, f c, h c, h c, h c, h c, h c, h c, f c, f c, f c, h c, h c, h c, h c, h c, h
LJ (Cement Joint) tapered socket and tapered spigot system Pipe PIV-1 100 PIV-2 150 PIV-3 200 PIV-4 250 PIV-5 300 PIV-6 300 PIV-7 350 PIV-8 400 PIV-9 450 PIV-10 500
EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
c, f c, f c, f c, f c, f c, h c, h c, h c, h c, h
FM Approvals
1-578
Product Designation
Pressure Rating*
Remarks
PIV-11 PIV-12 PIV-13 PIV-14 PIV-15 PIV-16 PIV-17 PIV-18 PIV-19 PIV-20 PIV-21 PIV-22 PIV-23 PIV-24 PIV-25 PIV-26 PIV-27 PIV-28 PIV-29 PIV-30 PIV-31 PIV-32 PIV-33 PIV-34 PIV-35 PIV-36 PIV-37 PIV-38 Fittings Saddle with Nipple SWN-1
600 250 300 300 350 400 450 500 600 100 150 200 250 300 300 350 400 450 500 600 250 300 300 350 400 450 500 600
EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST25/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5 EST16/FM12.5
c, h c, f c, f c, h c, h c, h c, h c, h c, h b, f b, f b, f b, f b, f b, h b, h b, h b, h b, h b, h b, f b, f b, h b, h b, h b, h b, h b, h
SWN-2
SWN-3
SWN-4
SWN-5
SWN-6
SWN-7
SWN-8
SWN-9
10014 10012 10034 1001 15014 15012 15034 1501 20014 20012 20034 2001 25014 25012 25034 2501 30014 30012 30034 3001 35014 35012 35034 3501 40014 40012 40034 4001 50014 50012 50034 5001 60014 60012 60034 6001
EST25/FM16
EST20/FM16
EST20/FM16
EST20/FM16
EST25/FM16
EST20/FM16
EST20/FM16
EST20/FM16
EST20/FM16
o o o
*Pressure ratings are determined by the FM part of the number. The EST designation refers to the manufacturers commercial (non-fire protection) ratings for these products. Specifically, FM 32 rated items are FM Approved for 32 bar (465 psi) service; etc. a. Spigot end(s). b. Socket end(s). c. Spigot end(s) Socket end(s). e. Bolt holes according to ASA150. f. 6 m (20 ft) length. g. 10 m (33 ft) length. h. 12 m (40 ft) length. m. Plain end(s).
FM Approvals
1-579
Future Pipe Industries BV, JC Kellerlaan 3, Box 255, 7770 AG Hardenberg, The Netherlands
LJ (Laminate) Jointed System.
Product Designation Nominal Pipe Size, mm Pressure Rating* Remarks
Pipe 12.3.08.15 12.3.08.14 11.3.08.05 11.3.10.51 11.3.15.51 11.3.15.50 11.3.20.51 11.3.20.50 11.3.25.51 11.3.25.50 CE (Cement) Jointed System. Pipe 12.3.08.45 12.3.08.44 11.3.08.35 11.3.08.45 11.3.13.51 11.3.14.51 11.3.18.51 11.3.19.51 11.3.18.50 11.3.19.50 11.3.23.51 11.3.24.51 11.3.23.50 11.3.24.50 11.3.28.51 11.3.29.51 11.3.28.50 11.3.29.50 11.3.23.40 11.3.23.41 11.3.28.40 11.3.28.41 11.3.33.40 11.3.38.40 11.3.43.40 11.3.24.41 11.3.24.40 11.3.29.41 11.3.29.40 11.3.34.40 11.3.39.40 11.3.44.40 Fittings Coupling 32.4.08.70 32.4.08.70 31.4.08.35 31.4.13.50 31.4.18.50 31.4.23.50 31.4.28.50 31.4.23.40 31.4.28.40 31.4.33.40 31.4.38.40 31.4.43.40 Fittings Adapter 32.4.05.71 31.4.05.45 31.4.08.45 32.4.08.71 31.4.14.50 31.4.19.50 31.4.24.50 31.4.29.50 31.4.24.40
EST40/FM40 EST40/FM40 EST32/FM32 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20
m, f m, g m, f m, f m, f m, g m, f m, g m, f m, g
80 80 80 80 100 100 150 150 150 150 200 200 200 200 250 250 250 250 200 200 250 250 300 350 400 200 200 250 250 300 350 400
EST40/FM40 EST40/FM40 EST32/FM32 EST32/FM32 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
c, f c, g c, f a, f c, f a, f c, f a, f c, g a, g c, f a, f c, g a, g c, f a, f c, g a, g c, g c, f c, g c, f c, g c, g c, g a, f a, g a, f a, g a, g a, g a, g
EST40/FM40 EST40/FM40 EST32/FM32 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
b, p b, p b b b b b b b b b b
a, p a a a, p a a a a b
FM Approvals
1-580
Product Designation
Pressure Rating*
Remarks
31.4.29.40 31.4.34.40 31.4.39.40 31.4.44.40 Fittings 90 Elbow 02.4.08.70 01.4.08.35 01.4.13.50 01.4.18.50 01.4.23.50 01.4.28.50 01.4.23.40 01.4.28.40 01.4.33.40 Fittings 45 Elbow 02.4.08.71 01.4.08.45 01.4.14.50 01.4.19.50 01.4.24.50 01.4.29.50 01.4.24.40 01.4.29.40 01.4.34.40 Fittings Equal Tee 12.4.08.70 11.4.13.50 11.4.18.50 11.4.23.50 11.4.28.50 11.4.23.40 11.4.28.40 11.4.33.40 Fittings Tee Reducing 12.4.08.71 11.4.08.36 11.4.23.51 11.4.28.52 11.4.23.42 11.4.23.41 11.4.28.43 11.4.28.42 11.4.28.41 11.4.33.44 11.4.33.43 11.4.33.42 11.4.33.41 Fittings Lateral 11.4.24.40 11.4.29.40 11.4.34.40 Fittings Concentric Reducer 41.4.23.42 41.4.23.41 41.4.28.42 41.4.28.41 41.4.33.42 41.4.33.41 Fittings Eccentric Reducer 41.4.24.42 41.4.24.41 41.4.29.42 41.4.29.41 41.4.34.42 41.4.34.41 Fittings Short Reducer 41.4.23.43 41.4.23.44
b b b b
b, p b b b b b b b b
b, p b b b b b b b b
b, p b b b b b b b
808050 80x80x50 200x200x150 250x250x150 200x200x100 200x200x150 250x250x100 250x250x150 250X250X200 300X300X100 300X300X150 300X300X200 300X300X250
EST40/FM40 EST32/FM32 EST25/FM20 EST25/FM20 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
b, p b b b b b b b b b b b b
b b b
b b b b b b
b b b b b b
200x100 200x150
EST20/FM16 EST20/FM16
b b
FM Approvals
1-581
Product Designation
Pressure Rating*
Remarks
41.4.28.43 41.4.28.44 41.4.33.43 41.4.33.44 41.4.38.43 41.4.38.44 41.4.43.43 41.4.43.44 Fittings Flange 25.4.05.70 21.4.05.35 21.4.08.35 25.4.08.70 21.4.13.50 21.4.18.50 21.4.23.50 21.4.28.50 21.4.23.40 21.4.28.40 21.4.33.40 21.4.23.42 21.4.28.42 21.4.33.42 21.4.24.40 21.4.29.40 21.4.34.40 21.4.24.42 21.4.29.42 21.4.34.42 Fittings Saddle with Nipple 64.4.21.89 64.4.21.90 64.4.21.91 64.4.21.92 64.4.21.93 64.4.28.33 64.4.28.34 64.4.28.35 64.4.28.36 64.4.28.37 Fittings Blind Flange 51.4.20.40 51.4.25.40 51.4.30.40 51.4.20.42 51.4.25.42 51.4.30.42
b b b b b b b b
50 50 80 80 100 150 200 250 200 250 300 200 250 300 200 250 300 200 250 300
EST40/FM40 EST32/FM32 EST32/FM32 EST40/FM40 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
b, e, p b, e b, e b, e, p b, e b, e b, e b, e b, e b, e b, e b, l b, l b, l b, e b, e b, e b, l b, l b, l
200x34 200x34 200x34 200x34 200x34 250x34 250x34 250x34 250x34 250x34
EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20
o o n n n o o n n n
e e e l l l
RSLJ (Rubber Seal Lock Joint) socket and spigot system. Pipe 12.3.08.75 80 12.3.08.74 80 11.3.08.15 80 11.3.11.51 100 11.3.16.51 150 11.3.16.50 150 11.3.21.51 200 11.3.21.50 200 11.3.26.51 250 11.3.26.50 250 11.3.21.40 200 11.3.21.41 200 11.3.26.40 250 11.3.26.41 250 11.3.31.40 300 11.3.36.40 350 11.3.41.40 400 Fittings Adapter 31.4.21.40 31.4.26.40 31.4.31.40 31.4.36.40
EST40/FM40 EST40/FM40 EST32/FM32 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST25/FM20 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
c, f c, g c, f c, f c, f c, g c, f c, g c, f c, g c, g c, f c, g c, f c, g c, g c, g
b b b b
FM Approvals
1-582
Product Designation
Pressure Rating*
Remarks
31.4.41.40 31.4.22.40 31.4.27.40 31.4.32.40 31.4.37.40 31.4.42.40 Fittings 90 Elbow 01.4.21.40 01.4.26.40 01.4.31.40 Fittings 45 Elbow 01.4.22.40 01.4.27.40 01.4.32.40 Fittings Equal Tee 11.4.21.40 11.4.26.40 11.4.31.40 Fittings Tee Reducing 11.4.21.42 11.4.21.41 11.4.26.43 11.4.26.42 11.4.26.41 11.4.31.44 11.4.31.43 11.4.31.42 11.4.31.41 Fittings Lateral 11.4.22.40 11.4.27.40 11.4.32.40 Fittings Concentric Reducer 41.4.21.42 41.4.21.41 41.4.26.42 41.4.26.41 41.4.31.42 41.4.31.41 Fittings Eccentric Reducer 41.4.22.42 41.4.22.41 41.4.27.42 41.4.27.41 41.4.32.42 41.4.32.41 Fittings Flange 21.4.21.40 21.4.26.40 21.4.31.40 21.4.21.42 21.4.26.42 21.4.31.42 21.4.36.42 21.4.41.42 21.4.21.43 21.4.26.43 21.4.31.43 21.4.22.40 21.4.27.40 21.4.32.40 21.4.22.42 21.4.26.42 21.4.32.42
b a a a a a
c c c
c c c
c c c
c c c c c c c c c
c c c
c c c c c c
c c c c c c
200 250 300 200 250 300 350 400 200 250 300 200 250 300 200 250 300
EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16 EST20/FM16
b, e b, e b, e b, e b, e b, e b, e b, e b, l b, l b, l a, e a, e a, e a, l a, l a, l
CE (cement) jointed system. Joints must be made with cement kit stock number 79.4.00.21. Pipe
FM Approvals
1-583
Product Designation
Pressure Rating*
Remarks
11.3.28.21 11.3.28.20 11.3.33.20 11.3.38.20 11.3.43.20 11.3.13.51 11.3.18.41 11.3.12.40 11.3.23.31 11.3.23.30 11.3.28.31 11.3.28.30 11.3.33.30 11.3.38.30 11.3.43.30 11.3.14.51 11.3.19.41 11.3.19.40 11.3.24.31 11.3.24.30 11.3.29.31 11.3.29.30 11.3.34.30 11.3.39.30 11.3.44.30 Fittings. Coupling 31.4.13.50 31.4.18.40 31.4.23.30 31.4.28.30 31.4.33.30 31.4.38.30 31.4.43.30 31.4.28.20 31.4.33.20 31.4.38.20 31.4.43.20 Adapter 31.4.14.50 31.4.19.40 31.4.24.30 31.4.29.30 31.4.34.30 31.4.39.30 31.4.44.30 31.4.29.20 31.4.34.20 31.4.39.20 31.4.44.20 90 Elbow 01.4.13.50 01.4.18.40 01.4.38.40 01.4.43.40 01.4.23.30 01.4.28.30 01.4.33.30 01.4.38.30 01.4.43.30 01.4.28.20 01.4.33.20 01.4.38.20 01.4.48.20 45 Elbow 01.4.14.50 01.4.19.40 01.4.39.40 01.4.44.40 01.4.24.30 01.4.29.30 01.4.34.30
250 250 300 350 400 100 150 150 200 200 250 250 300 350 400 100 150 150 200 200 250 250 300 350 400
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5
c, f c, g c, g c, g c, g c, f c, f c, g c, f c, g c, f c, g c, g c, g c, g a, f a, f a, g a, f l, g a, f a, g a, g a, g a, g
100 150 200 250 300 350 400 250 300 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
b b b b b b b b b b b
100 150 200 250 300 350 400 250 300 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
a a a a a a a a a a a
100 150 350 400 200 250 300 350 400 250 300 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
b b b b b b b b b b b b b
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5
b b b b b b b
FM Approvals
1-584
Product Designation
Pressure Rating*
Remarks
01.4.39.30 01.4.44.30 01.4.29.20 01.4.34.20 01.4.39.20 01.4.49.20 Tee 11.4.13.50 11.4.18.40 11.4.38.40 11.4.43.40 11.4.23.30 11.4.28.30 11.4.33.30 11.4.38.30 11.4.43.30 11.4.28.20 11.4.33.20 11.4.38.20 11.4.43.20 Tee Reducing 11.4.28.23 11.4.28.22 11.4.28.21 11.4.33.24 11.4.33.23 11.4.33.22 11.4.33.21 11.4.38.25 11.4.38.24 11.4.38.23 11.4.38.22 11.4.38.21 11.4.43.26 11.4.43.25 11.4.43.24 11.4.43.23 11.4.43.22 11.4.43.21 11.4.23.32 11.4.23.31 11.4.28.33 11.4.28.32 11.4.28.31 11.4.33.34 11.4.33.33 11.4.33.32 11.4.33.31 11.4.38.35 11.4.38.34 11.4.38.33 11.4.38.32 11.4.38.31 11.4.43.36 11.4.43.35 11.4.43.34 11.4.43.33 11.4.43.32 11.4.43.31 11.4.18.41 11.4.38.45 11.4.38.44 11.4.38.43 11.4.38.42 11.4.38.41 11.4.43.46 11.4.43.45 11.4.43.44 11.4.43.43 11.4.43.42 11.4.43.41 Lateral 11.4.14.50
b b b b b b
100 150 350 400 200 250 300 350 400 250 300 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
b b b b b b b b b b b b b
250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 200, 200, 250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 150, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400,
250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 200, 200, 250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 150, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400,
100 150 200 100 150 200 250 100 150 200 250 300 100 150 200 250 300 350 100 150 100 150 200 100 100 200 250 100 150 200 250 300 100 250 200 250 300 350 100 100 150 200 250 300 100 150 200 250 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b
100
EST 25 / FM 16
FM Approvals
1-585
Product Designation
Pressure Rating*
Remarks
11.4.19.40 11.4.24.30 11.4.29.30 11.4.34.30 11.4.29.20 11.4.34.20 Concentric Reducer 41.4.28.22 41.4.28.21 41.4.33.22 41.4.33.21 41.4.38.22 41.4.38.21 41.4.43.22 41.4.43.21 41.4.28.31 41.4.33.32 41.4.33.31 41.4.38.32 41.4.38.31 41.4.43.32 41.4.43.31 41.4.18.41 41.4.38.42 41.4.38.41 41.4.43.42 41.4.43.41 Eccentric Reducer 41.4.29.22 41.4.29.21 41.4.34.22 41.4.34.21 41.4.39.22 41.4.39.21 41.4.44.22 41.4.44.31 41.4.24.32 41.4.24.31 41.4.29.32 41.4.29.31 41.4.34.32 41.4.34.31 41.4.39.32 41.4.39.31 41.4.44.32 41.4.44.31 41.4.19.41 41.4.39.42 41.4.39.41 41.4.44.42 41.4.44.41 Short Reducer 41.4.28.23 41.4.28.24 41.4.33.23 41.4.33.24 41.4.38.23 41.4.38.24 41.4.43.23 41.4.43.24 41.4.23.33 41.4.23.34 41.4.28.33 41.4.28.34 41.4.33.33 41.4.33.34 41.4.38.33 41.4.38.34 41.4.43.33 41.4.43.34 41.4.18.44 Flange
EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10
b b b b b b
250, 250, 300, 300, 350, 350, 400, 400, 250, 300, 300, 350, 350, 400, 400, 150, 350, 350, 400, 400,
150 200 200 250 250 300 300 350 200 200 250 250 300 300 350 100 250 300 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
b b b b b b b b b b b b b b b b b b b b
250, 250, 300, 300, 350, 350, 400, 400, 200, 200, 250, 250, 300, 300, 350, 350, 400, 400, 150, 350, 350, 400, 400,
150 200 200 250 250 300 300 350 100 150 150 200 200 250 250 300 300 350 100 250 300 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
b b b b b b b b b b b b b b b b b b b b b b b
250, 250, 300, 300, 350, 350, 400, 400, 200, 200, 250, 250, 300, 300, 350, 350, 400, 400, 150,
150 200 200 250 250 300 300 350 100 150 150 200 200 250 250 300 300 350 100
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16
c c c c c c c c c c c c c c c c c c c
FM Approvals
1-586
Product Designation
Pressure Rating*
Remarks
21.4.13.60 21.4.18.40 21.4.38.40 21.4.43.40 21.4.23.30 21.4.28.30 21.4.33.30 21.4.38.30 21.4.43.30 21.4.28.20 21.4.33.20 21.4.38.20 21.4.43.20 21.4.13.52 21.4.18.42 21.4.38.42 21.4.43.42 21.4.23.32 21.4.28.32 21.4.33.32 21.4.38.32 21.4.43.32 21.4.28.22 21.4.33.22 21.4.38.22 21.4.43.22 21.4.14.50 21.4.19.40 21.4.39.40 21.4.44.40 21.4.24.30 21.4.29.30 21.4.34.30 21.4.39.30 21.4.44.30 21.4.29.20 21.4.34.20 21.4.39.20 21.4.44.20 21.4.14.52 21.4.19.42 21.4.39.42 21.4.44.42 21.4.24.32 21.4.29.32 21.4.34.32 21.4.39.32 21.4.44.32 21.4.29.22 21.4.34.22 21.4.39.22 21.4.44.22 Blind Flange 51.4.10.40 51.4.15.40 51.4.35.40 51.4.40.40 51.4.20.30 51.4.25.30 51.4.30.30 51.4.35.30 51.4.40.30 51.4.35.20 51.4.40.20 51.4.10.52 51.4.15.42 51.4.35.42 51.4.40.42 51.4.20.32 51.4.25.32 51.4.30.32 51.4.35.32 51.4.40.32 51.4.35.22 51.4.40.22
100 150 350 400 200 250 300 350 400 250 300 350 400 100 150 350 400 200 250 300 350 400 250 300 350 400 100 150 350 400 200 250 300 350 400 250 300 350 400 100 150 350 400 200 250 300 350 400 250 300 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, i b, i b, i b, i b, i b, i b, i b, i b, i b, i b, i b, i b, i a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, i a, i a, i a, i a, i a, i a, i a, i a, i a, i a, i a, i a, i
100 150 350 400 200 250 300 350 400 350 400 100 150 350 400 200 250 300 350 400 350 400
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10
e e e e e e e e e e e i i i i i i i i i i i
FM Approvals
1-587
Product Designation
Pressure Rating*
Remarks
RSLJ (rubber seal, lock joint) socket and spigot system. Joints are made using a rubber ring and a pvc cotter strip. Provides integral restraint against hydraulic forces.
Pipe 11.3.21.20 11.3.26.21 11.3.26.20 11.3.31.20 11.3.36.20 11.3.41.20 11.3.11.51 11.3.16.41 11.3.21.40 11.3.26.31 11.3.26.30 11.3.31.30 11.3.36.30 11.3.41.30 11.3.21.30 11.3.21.31 Adapter 31.4.26.20 31.4.31.20 31.4.36.20 31.4.41.20 31.4.21.30 31.4.26.30 31.4.31.30 31.4.36.30 31.4.41.30 31.4.11.50 31.4.16.40 31.4.27.20 31.4.32.20 31.4.37.20 31.4.42.20 31.4.22.30 31.4.27.30 31.4.32.30 31.4.37.30 31.4.42.30 31.4.12.50 Spools **67.4.xx.xx **68.4.xx.xx 90 Elbow 01.4.26.20 01.4.31.20 01.4.36.20 01.4.41.20 01.4.21.30 01.4.26.30 01.4.31.30 01.4.36.30 01.4.41.30 01.4.11.40 01.4.16.40 01.4.36.40 01.4.42.40 45 Elbow 01.4.27.20 01.4.32.20 01.4.37.20 01.4.42.20 01.4.22.30 01.4.27.30 01.4.32.30 01.4.37.30 01.4.42.30 01.4.12.50 01.4.17.40
200 250 250 300 350 400 100 150 150 250 250 300 350 400 200 200
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5
c, g c, f c, g c, g c, g c, g c, f c, f c, g c, f c, g c, g c, g c, g c, g c, f
250 300 350 400 200 250 300 350 400 100 150 250 300 350 400 200 250 300 350 400 100
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16
b b b b b b b b b b b a a a a a a a a a a
250 300 350 400 200 250 300 350 400 100 150 350 400
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
c c c c c c c c c c c c c
250 300 350 400 200 250 300 350 400 100 150
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16
c c c c c c c c c c c
FM Approvals
1-588
Product Designation
Pressure Rating*
Remarks
01.4.37.40 01.4.42.40 Tee 11.4.26.20 11.4.31.20 11.4.36.20 11.4.41.20 11.4.21.30 11.4.26.30 11.4.31.30 11.4.36.30 11.4.41.30 11.4.11.50 11.4.16.40 11.4.36.40 11.4.41.40 Tee-Reducing 11.4.26.23 11.4.26.22 11.4.26.21 11.4.31.24 11.4.31.23 11.4.31.22 11.4.31.21 11.4.36.25 11.4.36.24 11.4.36.23 11.4.36.22 11.4.36.21 11.4.41.26 11.4.41.25 11.4.41.24 11.4.41.23 11.4.41.22 11.4.41.21 11.4.21.32 11.4.21.31 11.4.26.33 11.4.26.32 11.4.26.31 11.4.31.34 11.4.31.33 11.4.31.32 11.4.31.31 11.4.36.35 11.4.36.34 11.4.36.33 11.4.36.32 11.4.41.31 11.4.41.36 11.4.41.35 11.4.41.34 11.4.41.33 11.4.41.32 11.4.41.31 11.4.16.41 11.4.36.45 11.4.36.44 11.4.36.43 11.4.36.42 11.4.36.41 11.4.41.46 11.4.41.45 11.4.41.44 11.4.41.43 11.4.41.42 11.4.41.41 Lateral 11.4.27.20 11.4.32.20 11.4.22.30 11.4.27.30 11.4.32.30
350 400
EST 20 / FM 16 EST 20 / FM 16
c c
250 300 350 400 200 250 300 350 400 100 150 350 400
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
c c c c c c c c c c c c c
250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 200, 200, 250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 150, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400,
250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 200, 200, 250, 250, 250, 300, 300, 300, 300, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400, 150, 350, 350, 350, 350, 350, 400, 400, 400, 400, 400, 400,
100 150 200 100 150 200 350 100 150 200 250 300 100 150 200 250 300 350 100 150 100 150 200 100 150 200 250 100 150 200 250 300 100 150 200 250 300 350 100 100 150 200 250 300 100 150 200 250 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c c
c c c c c
FM Approvals
1-589
Product Designation
Pressure Rating*
Remarks
11.4.12.50 11.4.17.40 Concentric Reducer 41.4.26.22 41.4.26.21 41.4.31.22 41.4.31.21 41.4.36.22 41.4.36.21 41.4.41.22 41.4.41.21 41.4.21.32 41.4.21.31 41.4.26.32 41.4.26.31 41.4.31.32 41.4.31.31 41.4.36.32 41.4.36.31 41.4.41.32 41.4.41.31 41.4.16.41 41.4.36.42 41.4.36.41 41.4.41.42 41.4.41.41 Eccentric Reducer 41.4.27.22 41.4.27.21 41.4.32.22 41.4.32.21 41.4.37.22 41.4.37.21 41.4.42.22 41.4.42.21 41.4.22.32 41.4.22.31 41.4.27.32 41.4.27.31 41.4.32.32 41.4.32.31 41.4.37.32 41.4.37.31 41.4.42.32 41.4.42.32 41.4.17.41 41.4.37.42 41.4.37.41 41.4.42.42 41.4.42.41 Flange 21.4.11.50 21.4.16.40 21.4.36.40 21.4.41.40 21.4.21.30 21.4.26.30 21.4.31.30 21.4.36.30 21.4.41.30 21.4.11.52 21.4.16.42 21.4.26.20 21.4.31.20 21.4.36.43 21.4.41.43 21.4.21.32 21.4.26.32 21.4.31.32 21.4.36.32 21.4.41.32 21.4.26.22 21.4.31.22
100 150
EST 25 / FM 16 EST 20 / FM 16
c c
250, 250, 300, 300, 350, 350, 400, 400, 200, 200, 250, 250, 300, 300, 350, 350, 400, 400, 150, 350, 350, 400, 400,
150 200 200 250 250 300 300 350 100 150 150 200 200 250 250 300 300 350 100 250 300 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
c c c c c c c c c c c c c c c c c c c c c c c
250, 250, 300, 300, 350, 350, 400, 400, 200, 200, 250, 250, 300, 300, 350, 350, 400, 400, 150, 350, 350, 400, 400,
150 200 200 250 250 300 300 350 100 150 150 200 200 250 250 300 300 350 100 250 300 300 350
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16
c c c c c c c c c c c c c c c c c c c c c c c
100 150 350 400 200 250 300 350 400 100 150 250 300 350 400 200 250 300 350 400 250 300
EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 25 / FM 16 EST 20 / FM 16 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10
b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, e b, l b, l b, l b, l b, l b, l b, l b, l b, l
FM Approvals
1-590
Product Designation
Pressure Rating*
Remarks
21.4.36.20 21.4.41.20 21.4.35.22 21.4.41.22 21.4.12.50 21.4.17.40 21.4.37.40 21.4.42.40 21.4.22.30 21.4.27.30 21.4.32.30 21.4.37.30 21.4.42.30 21.4.27.20 21.4.32.20 21.4.37.20 21.4.42.20 21.4.12.52 21.4.17.42 21.4.37.42 21.4.42.42 21.4.22.30 21.4.27.30 21.4.32.30 21.4.37.30 21.4.42.30 21.4.27.22 21.4.32.22 21.4.37.22 21.4.42.22
350 400 350 400 100 150 350 400 200 250 300 350 400 250 300 350 400 100 150 350 400 200 250 300 350 400 250 300 350 400
EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 25 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 20 / FM 16 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 16 / FM 12.5 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10 EST 12.5 / FM 10
b, l b, l b, l b, l a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, e a, l a, l a, l a, l a, l a, l a, l a, l a, l a, l a, l a, l a, l
Type
Remarks
3 (80) 4 (100) 6, 8, 10 (150, 200, 250) 12 (300) 4X3 (100 X 80) 6 X 3, 4 (150 X 80, 100) 8 X 3, 4, 6 (200 X 80, 100, 150) 10 X 3, 4, 6, 8 (250 X 80, 100, 150, 200) 12 X 3, 4, 6, 8, 10 (300 X 80, 100, 150, 200, 250) 4X3 (100 X 80) 6 X 3, 4 (150 X 80, 100) 8 X 4, 6 (200 X 100, 150) 10 X 6, 8 (250 X 150, 200) 12 X 8, 10 (300 X 200, 250) 3, 4 (80, 100) 6, 8, 10 (150, 200, 250) 12 (300) 3, 4 (80, 100) 6 (150) 8, 10 (200, 250)
365 (2515) 290 (2000) 180 (1240) 150 (1035) 290 (2000) 180 (1240) 180 (1240) 180 (1240) 150 (1035) 365 (2515) 290 (2000) 175 (1205) 175 (1205) 175 (1205) 365 (2515) 180 (1240) 175 (1205) 365 (2515) 290 (2000) 180 (1240)
k k k k
Unequal Tees
k k k k k
Concentric Reducers
k k k k k
Adapters
k k k
FM Approvals
1-591
Type
Remarks
12 (300) Flanges (w/socket ends) 3, 4 (80, 100) 6 (150) 8, 10 (200, 250) 12 (300) 3, 4 (80, 100) 6 (150) 8, 10 (200, 250) 12 (300) 3 (80) 4, 6 (100, 150) 8, 10, 12 (200, 250, 300)
175 (1205) 365 (2515) 290 (2000) 180 (1240) 175 (1205) 365 (2515) 290 (2000) 180 (1240) 175 (1205) 365 (2515) 290 (2000) 180 (1240)
k k k k
Blind Flanges
k, l k, l k, l k, l
Coupler
k k k
*Pressure ratings are determined by the FM part of the number. The EST designation refers to the manufacturers commercial (non-fire protection) ratings for these products. Specifically, FM 10 rated items are FM Approved for 10 bar (150 psi) service; FM 12.5 for 12.5 bar (180 psi); FM 16 for 16 bar (230 psi), etc. **This product designation is assigned to various system assemblies fabricated from FM Approved products at the manufacturers facilities. Each design variation will be identified by manufacturer, with four additional digits following the four listed above. The list of Spools will be available from the manufacturer. a. Spigot end(s). b. Socket end(s). c. Spigot end(s)socket end(s). d. 2 socket ends, 1 spigot end. e. Bolt holes according to ASA 150. f. 6 m (20 ft) length. g. 10 m (33 ft) length. i. Bolt holes according to DIN 16. k. Fittings available w/bell and spigot gasketed adhesive joints. l. Flanges available with 2 in. (50 mm) NPT tap and 1 in. (25 mm) BS tap. m. Plain end(s). n. Saddle cemented. o. Saddle laminated. p. Tapered.
Future Pipe Industries LLC-KSA, Box 8513, Dammam 31492, Kingdom of Saudi Arabia
Product Designation Nominal Pipe Size, mm Pressure Rating bar (psi) Remarks
Pipe with Plain Ends (PL/PL) PI-1 PI-2 PI-3 PI-4 PI-5 PI-6 PI-7 PI-8 PI-9 PI-10 PI-11 PI-12 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) a a a a a a a a a a a a
Pipe with Spigot and Socket Ends (CS/CB) PII-1 PII-2 PII-3 PII-4 100 150 200 250 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b
FM Approvals
1-592
Product Designation
Remarks
16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
b b b b b b b b
Pipe with Spigot and Socket Ends (FS/FB) PIII-1 PIII-2 PIII-3 PIII-4 PIII-5 PIII-6 PIII-7 PIII-8 PIII-9 PIII-10 PIII-11 PIII-12 Pipe with Spigot & Socket End, (TS/TB) PIV-1 PIV-2 PIV-3 PIV-4 PIV-5 PIV-6 PIV-7 PIV-8 PIV-9 PIV-10 150 200 250 300 350 400 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) c c c c c c c c c c 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) c c c c c c c c c c c c
90 Elbows Socket Ends (CB/CB) EL90-1 EL90-2 EL90-3 EL90-4 EL90-5 EL90-6 EL90-7 EL90-9 100 150 200 250 300 350 400 200 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) b b b b b b b b
FM Approvals
1-593
Product Designation
Remarks
b b b b
45 Elbows Socket Ends (CB/CB) EL45-1 EL45-2 EL45-3 EL45-4 EL45-5 EL45-6 EL45-7 EL45-9 EL45-10 EL45-11 EL45-12 EL45-13 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b b
Equal Tees Socket Ends (CB/CB/CB) ET-1 ET-2 ET-3 ET-4 ET-5 ET-6 ET-7 ET-9 ET-10 ET-11 ET-12 ET-13 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b b
Unequal Tees Socket Ends (CB/CB/CB) UT-2/B UT-3/B UT-3/C UT-4/B UT-4/C UT-4/D UT-5/B UT-5/C UT-5/D UT-5/E 150100 200100 200150 250100 250150 250200 300100 300150 300200 300250 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b b b b
FM Approvals
1-594
Product Designation
Remarks
UT-6/B UT-6/C UT-6/D UT-6/E UT-6/F UT-7/B UT-7/C UT-7/D UT-7/E UT-7/F UT-7/G UT-9/B UT-9/C UT-10/B UT-10/C UT-10/D UT-11/B UT-11/C UT-11/D UT-11/E UT-12/B UT-12/C UT-12/D UT-12/E UT-12/F UT-13/B UT-13/C UT-13/D UT-13/E UT-13/F UT-13/G
350100 350150 350200 350250 350300 400100 400150 400200 400250 400300 400350 200100 200150 250100 250150 250200 300100 300150 300200 300250 350100 350150 350200 350250 350300 400100 400150 400200 400250 400300 400350
16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b
Concentric Reducers Socket Ends (CB/CB) CR-2/B CR-3/A CR-3/B CR-4/A CR-4/B CR-5/A CR-5/B CR-6/A CR-6/B CR-7/A 150100 200100 200150 250150 250200 300200 300250 350250 350300 400300 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) b b b b b b b b b b
FM Approvals
1-595
Product Designation
Remarks
CR-7/B CR-9/A CR-9/B CR-10/A CR-10/B CR-11/A CR-11/B CR-12/A CR-12/B CR-13/A CR-13/B
400350 200100 200150 250150 250200 300200 300250 350250 350300 400300 400350
16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
b b b b b b b b b b b
Adaptor Spigot Ends (CS/CS) AdapI-1 AdapI-2 AdapI-3 AdapI-4 AdapI-5 AdapI-6 AdapI-7 AdapI-8 AdapI-9 AdapI-10 AdapI-11 AdapI-12 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b b
Coupler Socket Ends (CB/CB) CplrI-1 CplrI-2 CplrI-3 CplrI-4 CplrI-5 CplrI-6 CplrI-7 CplrI-9 CplrI-10 CplrI-11 CplrI-12 CplrI-13 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) b b b b b b b b b b b b
Flange with Socket End (CB/FL) F-1 F-2 F-3 100 150 200 16.0 (232) 16.0 (232) 16.0 (232) b b b
FM Approvals
1-596
Product Designation
Remarks
16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
b b b b b b b b b
Blind Flange, FL BF-1 BF-2 BF-3 BF-4 BF-5 BF-6 BF-7 BF-8 BF-9 BF-10 BF-11 BF-12 100 150 200 250 300 350 400 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180) 12.5 (180)
Saddle with Nipple. SaN-1 SaN-2 SaN-3 SaN-4 SaN-5 SaN-6 SaN-7 100 150 200 250 300 350 400 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) 16.0 (232) d d d d d d d
b b b
Epoxy Pipe
FM Approvals
1-597
Product Designation
Remarks
P-4 P-5 P-6 Epoxy Fittings. Elbows (90 and 45) EL 13, 12 EL 7 EL 6 EL 5 EL 4 EL 3 Concentric Reducers CR 18 CR 17 CR 7 CR 6 CR 5 CR 4 CR 12 CR 11 CR 1 Equal Tees ET 13 ET 7 ET 6 ET 5 ET 4 ET 3 Unequal Tees UT 38 UT 37 UT 36 UT 35 UT 34 UT 19 UT 18 UT 17 UT 16 UT 14 UT 13 UT 12 UT 11 UT 10 UT 9 Flange (w/socket end)
80 100 150
a a a
230 (1600) 180 (1240) 180 (1240) 180 (1240) 365 (2515) 365 (2515) 230 (1600) 230 (1600) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 290 (2000) 290 (2000) 365 (2515) 230 (1600) 180 (1240) 180 (1240) 180 (1240) 290 (2000) 365 (2515) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 230 (1600) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 180 (1240) 290 (2000)
e e e e e e
e e e e e e e e e
e e e e e e
300250 300200 300150 300100 30080 250200 250150 250100 25080 200150 200100 20080 150100 15080 10080
e e e e e e e e e e e e e e e
FM Approvals
1-598
Product Designation
Remarks
FS 3 FS 5 FS 10 FS 11 FS 12 FS 13 Blind Flanges BF 4 BF 5 BF 11 BF 12 BF 13 BF 14 GEI/FM/541001-1 GEI/FM/541001-2 GEI/FM/541001-3 GEI/FM/541001-4 GEI/FM/541001-5 Full Vinylester Pipe GE/FM/51001-1 GE/FM/51001-2 GE/FM/51001-3 GE/FM/51001-4 GE/FM/51001-5 GE/FM/51001-6 Vinylester/Polyester Pipe GE/FM/51002-1 GE/FM/51002-2 GE/FM/51002-3 GE/FM/51002-4 GE/FM/51002-5 GE/FM/51003-1 GE/FM/51003-2 GE/FM/51003-3 GE/FM/51003-4 GE/FM/51003-5 Vinylester/Polyester Pipe GE/FM/51-1 GE/FM/51-2 GE/FM/51-3 GE/FM/51-4 GE/FM/51-5 Vinylester/Polyester Fittings. Concentric Reducers GE/FM/52400-1
465 (3200) 365 (2500) 290 (2000) 230 (1600) 230 (1600) 230 (1600) 465 (3200) 365 (2500) 290 (2000) 230 (1600) 230 (1600) 230 (1600) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 365 (2500) 290 (2000) 230 (1600) 230 (1600) 180 (1250) 180 (1250) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 175 (1200) 150 (1050)
e e e e e e
80 100 150 200 250 300 350 400 450 500 600
e, f e, f e, f e, f e, f e, f e, f e, f e, f e, f e, f
b b b b b b
100 150 200 250 300 350 400 450 500 600
c c c c c c c c c c
d d d d d
600500
150 (1050)
FM Approvals
1-599
Product Designation
Remarks
GE/FM/52400-2 GE/FM/52400-3 GE/FM/52400-4 GE/FM/52400-5 GE/FM/52400-6 GE/FM/52400-7 GE/FM/52400-8 GE/FM/52400-9 GE/FM/52400-10 GE/FM/52400-11 GE/FM/52400-12 GE/FM/52400-13 GE/FM/52400-14 GE/FM/52400-15 Tees GE/FM/52300-1 GE/FM/52300-2 GE/FM/52300-3 GE/FM/52300-4
a. Pipe lengths are joined with cemented couplers CPLR 1-3. b. Pipe lengths are joined with cemented couplers GE/FM/56001 1-6. c. Pipe lengths are joined with double gasketed coupler GE/FM/5335 1-10.
600450 600400 600350 600300 500450 500400 500350 500300 450400 450350 450300 400350 400300 350300
150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050) 150 (1050)
e e e e e e e e e e e e e e
e e e e
d. Pipe lengths are joined with buttstrap joint. e. Fittings available with adapters for joining to pipe and flanges. f. Flanges available with 2 in. (50 mm) NPT tap and 1 in. (25 mm) BS tap.
Iniziative Industriali SPA, Via Rosignanina 14 56040, Santa Luce (PI) Localita, Macchiaverde Italy
Product Designation Nominal Pipe Size, in. Pressure Rating, bar (psi) Remarks
Conc. Reducer
Exc. Reducer
4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20
a, b, c a, b, c a, b, c a, b, c
16 (230)
a, b, c
16 (230)
a, b, c
16 (230) 16 (230)
a, b, c a, b, c
FM Approvals
1-600
Product Designation
Remarks
End Cap
16 (230)
a, b, c
a. Pipe and fittings available with double-gasketed bell and spigot joints. b. Pipe and fittings available with buttstrap joints. c. Pipe and fittings available with Plastiwind Lock Joint. Tested and evaluated for use unrestrained. Product Designation Nominal Pipe Size, in. Pressure Rating, bar (psi)
Remarks
Conc. Reducer
Exc. Reducer
4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 54; 65, 4; 86, 5, 4; 108, 6, 5, 4; 1210, 8, 6, 5; 1412, 10, 8, 6; 1614, 12, 10, 8; 1816, 14, 12, 10; 2018, 16, 14, 12 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20 4, 5, 6, 8, 10, 12, 14, 16, 18, 20
a, b, c a, b, c a, b, c a, b, c
20 (290)
a, b, c
20 (290)
a, b, c
a, b, c a, b, c a, b, c
a. Pipe and fittings available with double-gasketed bell and spigot joints. b. Pipe and fittings available with buttstrap joints. c. Pipe and fittings available with Plastiwind Lock Joint. Tested and evaluated for use unrestrained.
FM Approvals
1-601
National Oilwell Varco, Smith Fibercast Products Div, 2700 W 65th St, Little Rock AR 72209
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa)
Remarks
Pipe, Class 200 011040-073-3 011060-120-3 011080-126-3 011100-156-3 011120-185-3 011140-220-3 011160-250-3 Fittings, Sleeve Coupling, Class 200 012040-101-5 012060-101-3 012080-101-3 012100-101-3 012120-101-3 012140-101-3 012160-101-3 Elbow 45, Class 200 022040-310-3 022060-310-3 022080-310-3 022100-310-3 022120-310-3 022140-310-3 022160-310-3 Elbow 90, Class 200 022040-360-3 022060-360-3 022080-360-3 022100-360-3 022120-360-3 022140-360-3 022160-360-3 Equal Tee, Class 200 4 6 8 10 12 14 16 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) d, e d, e d, e d, e d, e d, e d, e 4 6 8 10 12 14 16 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) d, e d, e d, e d, e d, e d, e d, e 4 6 8 10 12 14 16 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) d, e, f d, e, f d, e, f d, e, f d, e, f d, e, f d, e, f 4 6 8 10 12 14 16 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) a, b, c, d, f a, b, c, d, f a, b, c, d, f a, b, c, d, f a, b, c, d, f a, b, c, d, f a, b, c, d, f
FM Approvals
1-602
Product Designation
Remarks
022040-410-3 022060-410-3 022080-410-3 022100-410-3 022120-410-3 022140-410-3 022160-410-3 Concentric Reducer, Class 200 022060-236-3 022080-237-3 022080-235-3 022100-237-3 022100-235-3 022120-237-3 022120-235-3 022140-237-3 022140-235-3 022160-237-3 022160-235-3 Flange, Class 200 022040-172-3 022060-172-3 022080-172-3 022100-172-3 022120-172-3 022140-172-3 022160-172-3 Reducing Tee Class 200 022080-460-3 022100-460-3 022100-480-3 022120-460-3 022120-480-3
4 6 8 10 12 14 16
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
d, e d, e d, e d, e d, e d, e d, e
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
d, e d, e d, e d, e d, e d, e d, e d, e d, e d, e d, e
4 6 8 10 12 14 16
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
d, e d, e d, e d, e d, e d, e d, e
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
d, e d, e d, e d, e d, e
FM Approvals
1-603
Product Designation
Remarks
022120-490-3 022140-460-3 022140-480-3 022140-490-3 022140-490-3 022160-460-3 022160-480-3 022160-490-3 022160-492-3 022160-494-3 FW Filament wound manufacturing process. CNC Winder Use for 8 in. and above.
Remarks a. b. c. d. e. f.
1210 146 148 1410 1412 166 168 1610 1612 1614
200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380) 200 (1380)
d, e d, e d, e d, e d, e d, e d, e d, e d, e d, e
Pipe lengths available in two configurations: two spigot ends or one spigot and one bell end. Pipes equipped with two spigot ends joined by sleeve couplings. Pipes equipped with one bell and one spigot end joined by bell and spigot joints. Joints must be made with adhesive kit No. 7014, 7069, 7024 or 7054. Fittings with bell ends. Joints must be made with adhesive kit No. 8014, 8024, 8069 or 8069-C.
N Sguassero Spa, Via Pasubio 36, 20037 Paderno Dugnano (MI), Italy
NP 16 G.R.P. Pipes And Fittings
Product Designation Nominal Pipe Size, in. (mm) Pressure Rating, bar (psi) Remarks
Pipe 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Butt and Strap Lamination 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Elbows 90 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Fixed Flange 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Stub End Flange 20 20 16 16 14 16 12 (290) (290) (230) (230) (205) (230) (175) 20 16 16 16 16 16 16 (290) (230) (230) (230) (230) (230) (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 10.5 (150) 16 (230) 16 (230) 16 (230) 16 (230) 14 (205) 16 (230) 10.5 (150)
a, b, c
a, b
a, b, c
a, b, c
a, b, c
FM Approvals
1-604
Product Designation
Remarks
4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Cap 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Equal Tee 4 6 8 10 12 16 20 Unequal Tee 54, 64, 65 84, 85, 86 105, 106, 108, 126, 128, 1210, 148, 1410, 1412, 1610, 1612, 1614, 1812, 1814, 1816, 2014, 2016, 2018 Concentric Reducers Eccentric Reducers 54, 64, 65 84, 85, 86 105, 106, 108 126, 128, 1210 148, 1410, 1412 1610, 1612, 1614 1812, 1814, 1816 2014, 2016 2018
20 20 16 16 14 16 12 20 16 16 16 16 16 16 20 20 16 12 12 12 12 20 16 12 12 12 12 12 12 12 12 12
(290) (290) (230) (230) (205) (230) (175) a, b, c (290) (230) (230) (230) (230) (230) (230) a, b, c (290) (290) (230) (175) (175) (175) (175) a, b, c (290) (230) (175) (175) (175) (175) (175) (175) (175) (175) (175) a, b, c
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 10.5 (150)
a. Pipe and fittings available with double O-ring seal. b. Pipe and fittings available with butt and strap lamination. c. Pipe and fittings with re-useable nylon locking keys as joint restraints.
Glass Reinforced Polyester Resin Pipes and Fittings, with Glued Joints
Glued Joint 4 6 8 10 12 16 Elbows 90 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Fixed Flange 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Stub End Flange 20 (290) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) a, b, c 20 (290) 20 (290) 16 (230) 16 (230) 14 (205) 16 (230) 12 (175) a, b, c 20 16 16 16 (290) (230) (230) (230) b
14 (200) 16 (230) a, b, c
FM Approvals
1-605
Product Designation
Remarks
4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Cap 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) 16 (400) 20 (500) Equal Tee 4 6 8 10 12 16 20 Unequal Tee 54, 64, 65 84, 85, 86 105, 106, 108, 126, 128, 1210, 148, 1410, 1412, 1610, 1612, 1614, 1812, 1814, 1816, 2014, 2016, 2018 Concentric Reducers Eccentric Reducers 54, 64, 65 84, 85, 86 105, 106, 108 126, 128, 1210 148, 1410, 1412 1610, 1612, 1614 1812, 1814, 1816 2014, 2016 2018
a. Pipe and fittings available with double O-ring seal. b. Pipe and fittings available with butt and strap lamination. c. Pipe and fittings with re-useable nylon locking keys as joint restraints.
20 20 16 16 14 16 12 20 16 16 16 16 16 16 20 20 16 12 12 12 12 20 16 12 12 12 12 12 12 12 12 12
(290) (290) (230) (230) (205) (230) (175) a, b, c (290) (230) (230) (230) (230) (230) (230) a, b, c (290) (290) (230) (175) (175) (175) (175) a, b, c (295) (230) (175) (175) (175) (175) (175) (175) (175) (175) (175) a, b, c
16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 16 (230) 10.5 (150)
TPR Fiberdur GmbH + Co KG, Industriepark Emil Mayrisch, D-52457 Aldenhoven/Siersdorf, Germany
Product Designation Nominal Pipe Size, in. Pressure Rating, psi (kPa)
Remarks
50 80 100 150
50 80 100 150
50 80
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
a, b, c a, b, c a, b, c a, b, c a, d a, d a, d a, d a, d a, d
FM Approvals
1-606
Product Designation
Remarks
100 150 Coupling Type 514 Coupling Type 514 50 80 100 150
175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205) 175 (1205)
a, d a, d a, d a, d a, d a, d
a. Joints must be made with Fiberdur epoxy adhesive. b. Pipes equipped with two spigot ends. Pipe lengths joined by Type 514 couplings. c. Pipes equipped with one bell and one spigot end. Pipe lengths joined by bell and spigot joints. d. Fittings with bell ends.
Fiberdur VE 16 Pipe with Bell and Spigot Joint connected by Type VE 16 coupling 90 Elbow VE 16
45 Elbow VE 16
Tee, VE 16
Coupling VE 16
2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300) 2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300) 2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300) 2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300) 2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300) 2, 3, 4, 6, 8, 10, 12 (50, 80, 100, 150, 200, 250, 300)
225 (1550)
a, b, c
225 (1550)
a, b, c
225 (1550)
a, d
225 (1550)
a, d
225 (1550)
a, d
225 (1550)
a, d
a. Joints must be made with Fiberdur epoxy adhesive. b. Pipes equipped with two spigot ends. Pipe lengths joined by VE 16 couplings. c. Pipes equipped with one bell and one spigot end. Pipe lengths joined by bell and spigot joints. d. Fittings with bell ends.
PIPE HANGERS
Pipe hangers are used to support a sprinkler piping system from the building structure. Two or more listed components may be required to form a complete hanger. The specific components required depend upon the type of building construction and the pipe size.
Ring Pipe Hanger Ring Pipe Hanger Small Mouth Beam Clamp Small Mouth Beam Clamp Wide Throat Beam Clamp Wide Throat Beam Clamp
1 through 4 6 through 8
3 4
through 4
5 through 8
3 4
through 4
5 through 8
FM Approvals
1-607
Component Description
3 4
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
65 69 69 69 69E 86 87 88*
1 2 3 8 3 8 1 2 10 12 3 8 3 8 3 8
Clevis Hanger Adjustable Swivel Ring Hanger C-Clamp with C.P. Set Screw and Locknut C-Clamp with C. P. Retaining Clip C-Clamp with C. P. Set Screw
212 through 4 34 through 2 212, 3, 4 5 through 8 34 through 4 5 through 8 34 through 4 34 through 4 34 through 4
*Limited to steel beams which are tilted so hanger cannot slide. For Nominal Pipe Sizes, in.
Product Designation
Component Description
92 and 92E 92 93 93 97 97 97 97 97 110R 110R 134 134 136 136 153 153 157 157 194 194 202 202 206 206 207 212 212 212 212 212 218 227 260 260 260 260 260
Beam C-Clamp Standard Throat Beam C-Clamp Wide Throat Adjustable Pipe Ring Threaded Sockets (Rod Attachment) I-Beam Clamp Rod Coupling Pipe Hanger Flange Extension Piece Extension Piece Light Welded Steel Bracket Side Beam Bracket Side Beam Bracket Steel Side Beam Bracket Side Beam Bracket Wrought Pipe Clamp I-Beam Clamp with Fig. 157 Extension Piece Top Beam Clamp Clevis Hanger
3 4
through 4
5 through 8
3 4
through 4
5 through 8 34 through 2 212 through 312 4, 5 6 8 34 through 4 5 through 8 5 through 8 10, 12 34 through 4 5 through 8 34 through 4 5 through 8 34 through 4 5 through 8 34 through 4 5 through 8 34 through 4 5 through 8 34 through 4 5 through 8 34 through 4 34 through 2 212 through 312 4, 5 6 8 34 through 4 through 4 through 2 212 through 312 4, 5 6 8
3 4 3 4
Approved for use on steel or wood beam. Approved for use on steel beam only. # These hanger components are also FM Approved when threaded for use with the nearest equivalent standard metric size hanger rod.
FM Approvals
1-608
Bolivar Ltd, Devonshire Works West Lane, Keighley, West Yorkshire BD21 2LB, United Kingdom
Product Designation Hanger Rod Size, in. (in.) Component Description For Nominal Pipe Sizes, mm (in.)
10 (38) 10 ( 3 8) 10 ( 3 8) 10 ( 3 8) 10 ( 3 8) 10 ( 3 8) 10 ( 3 8) 10 ( 3 8) 12 ( 1 2) 12 ( 1 2)
Pipe Hanger
20 (34) 25 (1) 32 (114) 40 (112) 50 (2) 65 (212) 80 (3) 100 (4) 125 (5) 150 (6)
CCTF Corp, #4-480 Audley Blvd, Delta, British Columbia V3M 5S4, Canada
Product Designation Component Description Nominal Rod Size, in.
38 (10) 12 (12)
A100 A100
through 4
5 through 8
Debro Engineering & Presswork, Stourvale Trading Estate, Banners Ln, Halesowen B63 2AX, United Kingdom
Product Designation Hanger Rod Size, mm Component Description For Nominal Pipe Sizes, in.
34
FIL00272 FIL00342 FIL00422 FIL00482 FIL00602 FIL00762 FIL00892 FIL01142 FIL01412 FIL01682 FIL02192 SPH00272 SPH00342 SPH00422 SPH00482 SPH00602 SPH00762 SPH00892 SPH01142 SPH01413 SPH01683 SPH02193 USP2010 USP2510 USP3210 USP4010 USP5010 USP65
10 10 10 10 10 10 10 10 12 18 M10 M10 M10 M10 M10 M10 M10 M10 M12 M12 M16 M10 M10 M10 M10 M10 M10 M10 M10 M12 M12 M12 M10 M10 M10 M10 M10 M10
Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow Filbow
1 114 112 2 212 3 4 6 8 34 1 114 112 2 212 3 4 5 6 8 34 1 114 112 2 212 3 4 5 6 8 34 1 114 112 2 212
FM Approvals
1-609
Product Designation
Component Description
3 4 5 6 8
Caddy TKN M10 P1 Caddy TKN10 P1 Caddy TKN-M12 P1 Caddy TKN12 P1 TK16 M10 TK16 11 TK16 38 TK16 M12 TK16 13 TK16 12 TK16 M16 TK16 17 TK16 58
Beam Clamp
through 4 through 4 5 through 8 5 through 8 34 through 4 34 through 4 34 through 4 34 through 8 34 through 8 34 through 8 34 through 8 34 through 8 34 through 8
For European jurisdictions that prefer to use clearance holes for the threaded rod and hex jam nuts to secure the rods to the beam clamps.
Component Description
M10 M12
Beam C-Clamp
3 4
through 4 5 through 8
Component Description
1 37 37 38 100 100 100 100 100 115 115 115 130 130 Model 135 Model 135CT *Model 137 300I 300 300
Loop Hanger Eye Socket Offset Eye Socket Adjustable Swivel Hanger Yook Loop C-Clamp Top Beam Clamp & C-Clamp with
212
3 4 3 4
212, 312 4, 5 6 8
3 4
through 2
through 4
5 through 8
3 4 3 4
4 2 2 4
through 4 through 8
FM Approvals
1-610
Product Designation
Component Description
300 300D 300D 310 310 310 310 315 400, 401, 406, 420, 420EP 400, 401, 406, 420 , 420EP 400, 401, 406, 420 , 420EP 401EG, 401RO, 401HD 401EG, 401RO, 401HD 401EG, 401RO, 401HD 427 Fig. 1 Fig. 1 Fig. 1 35** 36** 37 37 58 128BTS 547 548 FCS FCS FCS
C-Clamp Top Beam Clamp & C-Clamp with Big Mouth Beam Clamp Top Beam Clamp Purlin Klif Klamp Clevis Hanger Clevis Hanger Swivel Pipe Loop Standard C-Clamp Wide Throat C-Clamp Steel Side Beam Bracket Ceiling Plate Steel Clamp Loop Hanger Loop Hanger Loop Hanger
5 through 8
3 4
through 4 312
3 4
through 4
212 through 312 4, 5 6, 8 212 through 312 4, 5 6, 8 2 and 4 through 2 212 through 4 5 through 8 34 through 4 5 through 8 34 through 4 5 through 8 4
3 4 3 4
through 2 4 8 34 through 4 5, 6 8
**FM Approved for use in the top and inverted bottom beam positions. These hanger components are also FM Approved when threaded for use with the nearest equivalent standard metric size hanger rod. Model 135 Yook Lo op Hanger using two MCO 43-16 wood screw fasteners in each arm is FM Approved to support 34 through 4 in. NPS sprinkler system piping. Model 135CT Yook Loop Hanger using two MCO 43-16 wood screw fastener in each arm is FM Approved to support 34 through 2 in. NPS sprinkler system copper tubing. *Model 137 Yook Loop Hanger using one MCO 43-16 wood screw fastener in each arm is FM Approved to support 34 through 2 in. NPS sprinkler system piping.
These hanger components are also FM Approved when threaded for use with the nearest equivalent standard metric size hanger rod. The suffix -M appears after the model number.
Empire Industries Inc, 180 Olcott St, Box 1020, Manchester CT 06045-1020
Product Designation Hanger Rod Size, in. NC
3 8 1 2 5 8 3 4 7 8 3 8 3 8 3 8 3 8
Component Description
Clevis Hanger Steel C-Clamp C-Clamp with Set Screw & Locknut C-Clamp with Set Screw & Retaining Strap Em-Lok Adjustable Swivel Ring Hanger
through 4 through 2
FM Approvals
1-611
Product Designation
Component Description
Wide Mouth Beam Clamp Wide Mouth Beam Clamp Wide Mouth Beam Clamp Wide Mouth Beam Clamp C-Clamp C-Clamp
3 4
BCS BCS BES BES BKS10 BKS12 KC10 KC12 KCK 10 KCK 12 KCS * TKN-10 * TK-12 LTM**
10 12 10 12 10 12 10 12 10 12 10 M10, 11 M12, 13 10
Loop Hanger Loop Hanger Adjustable Loop Hanger Pipe Hanger C-Clamp C-Clamp Standard and Top Beam Clamps C-Clamp Beam Clamp Beam Clamp Trapeze Hanger
through 4
5 through 8
3 4
through 4
5 through 8
3 4
through 312
4 through 8
3 4
through 4
5 through 8
3 4
through 4
5 through 8
3 4 3 4
through 4 through 4
5 through 8
3 4
through 3
* with cup point set screw **Approval limited to minimum allowable steel deck thickness of 0.75 mm (0.03 in.) and greater. For European jurisdictions that prefer to use clearance holes for the threaded rod and hex jam nuts to secure the rods to the beam clamps.
All pipe hangers are FM Approved for use with U.S. NC 38-16 and NC 12-13 threaded rod as an alternate to the metric rod. Markings so designate appropriate rod.
Globe Pipe Hanger Products Inc, 14601 Industrial Pkwy, Cleveland OH 44135
Product Designation Hanger Rod Size, in. (mm) NC
3 8 3 8 38 38 38 38 38 38 38 38 38 12 12 12
Component Description
103-101 113-101 300-206 300-210 300-212 300-214 300-220 304-224 304-230 304-234 304-240 304-250 304-260 304-280
(10)* (10)* (10)* (10)* (10)* (10)* (10)* (10)* (10)* (12)* (12)* (12)*
Malleable Beam Clamp w/lock nut Wide Throat Beam Malleable Clamp w/lock nut Special Pipe Hanger
3 4 3 4
through 4 through 4
3 4
*These hanger components are also FM Approved when threaded for use with the nearest equivalent standard metric size hanger rod, M10 or M12, as shown. The suffix -MM appears after the model number for hangers using Metric rods.
FM Approvals
1-612
Hilti AG, Feldkircher Str 100, Postfach 333, FL-949 Schaan, Fuerstentum Liechtenstein
Product Designation Hanger Rod Size, in. NC Component Description For Nominal Pipe Size, in.
MP-SP
MP-MS MP-MS2 MF-SKD-M10 MF-TSH-M10 LH 34 LH 1 LH 114 LH 1-12 LH 2 LH 212 LH 3 LH 4 LH 6 LH 8 BC-WM 38 BC-WM 12 BC 38 BC 12 SDC-EG 212 SDC-EG 3 SDC-EG 4 SDC-EG 5 SDC-EG 6 SDC-EG 8 SLC-EG SLC-EG SLC-EG SLC-EG
10 12 16 10 12 16 10 10 38 3 8 38 38 3 8 38 3 8 3 8 1 2 1 2 38 12 38 12 12 1 2 5 8 5 8 3 4 3 4 3 8 1 2 5 8 3 4
Loop Hanger Pipe Clamp Hanger Toggle Suspension Hanger Loop Hanger Beam Clamp Beam Clamp Clevis Hanger
Clevis Hanger
Lindapter International, Lindsay House Brackenbeck Rd, Bradford, West Yorkshire BD7 2NF, United Kingdom
Product Designation Hanger Rod Size, mm Component Description For Nominal Pipe Sizes, in.
3 4 3 4 3 4 3 4 3 4 3 4
10122 10115 10096 FL 2 (Malleable Iron) FL2 with swivel (Malleable Iron) FL 2 (Stainless Steel) FL 3 M10 FLS M10 Swiftgrip M10 Swiftgrip Swivel Unit 38 FL S SH SH SH TC
Type F3 Flange Clamp Single Boss Split Pipe Ring Type FL Flange Clamp Type FL Flange Clamp Type FL Flange Clamp Swivel Beam Clamp Swiftgrip Beam Clamp Swiftgrip Beam Clamp with Swivel Swivel Beam Clamp Loop hanger Toggle Clamp
FM Approvals
1-613
S S S S
34,
Minimax GmbH & Co KG, Box 1260, Industriestrasse 10-12, D-23840 Bad Oldesloe, Germany
Product Designation Hanger Rod Size, in. (mm)
3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 1 2 (12) 1 2 (12) 5 8 (16)
Component Description
SM 20/10 SM 25/10 SM 32/10 SM 40/10 SM 50/10 SM 65/10 SM 80/10 SM 100/10 SM 125/12 SM 150/12 SM 200/16
3 4
through 1
1 through 114 114 through 112 112 through 2 2 through 212 212 through 3 3 through 4 4 through 5 5 through 6 8
*FM Approved for use in the top and inverted bottom beam positions.
10 12 10 12 10 12
3 4 3 4
through 4 5 through 8
Myland Industrial Co Ltd, Room 708, Metro Centre 32 Lam Hing St, Kowloon Bay Hong Kong
Figure 350 Figure 350 Figure 360 Figure 360 Figure 270 Figure 270
3 8 1 2 3 8 1 2 3 8 1 2
Top or Bottom Beam Clamp Bottom Beam Clamp Wide Mouth Top or Bottom Beam Clamp Wide Mouth Bottom Beam Clamp C- Clamp
3 4
3 4
Component Description
Offset Steel Eye Socket Swivel Ring Loop Hanger Swivel Ring Loop Hanger Swivel Ring Loop Hanger Swivel Ring Loop Hanger Swivel Ring Loop Hanger
3 4
FM Approvals
1-614
Product Designation
Component Description
151 253 290 353 354 363 364 450 450 450 450 550 907 908
Swivel Ring Loop Hanger Pressed Steel C-Clamp Purlin Clamp Spartan Top Beam C-Clamp Spartan Top Beam C-Clamp Spartan Top Beam C-Clamp Spartan Top Beam C-Clamp Clevis Hanger Clevis Hanger Clevis Hanger Clevis Hanger Riser Clamp Side Beam Braket Side Beam Connector
8 through 4 through 4 34 through 4 5 through 8 34 through 4 5 through 8 212 through 312 4, 5 6 8 34 through 312 34 through 4 34 through 4
3 4 3 4
SMK Meister GmbH & Co KG, Lombacher Strasse 53, Postfach 27, 72293 Glatten, Germany
Product Designation Hanger Rod Size, in. NC Component Description For Nominal Pipe Sizes, in.
10 10 10 12 12
3 4
Shanghai Vision Mechanical Joint Co Ltd, No. 221 Jinlan Road, Loutang Industrial Park, Jaiding District, Shanghai 201807, Peoples Republic China
Product Designation Nominal Rod Size, in. (mm)
3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 1 2 (12) 1 2 (12) 1 2 (12)
Component Description
702-34 in. (DN20) 702-1 in. (DN25) 702-114 in. (DN32) 702-112 in. (DN40) 702-2 in. (DN50) 702-212 in. (DN65) 702-3 in. (DN80) 702-4 in. (DN100) 702-5 in. (DN125) 702-6 in. (DN150) 702-8 in. (DN200)
Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger Loop Pipe Hanger
Shurjoint Piping Products Inc, 4601 E Cheyenne Ave, Suite 105, Las Vegas NV 89115
Product Designation Hanger Rod Size, in. (mm)
3 8 (10) 3 8 (10)
Component Description
B20 B24
through 4 through 4
FM Approvals
1-615
Praktica S-VA
Praktica S
10 12 16 10 12 16 10 10 12, 16 10 10 10 12 16
Eye Rod Size, in. (mm)
Loop Hanger Loop Hanger C-Clamp Beam Clamp Tipping Dowel Loop Hanger
Component Description
Product Designation
STABIL Group 1233 118833 118842 118851 118860 118879 118888 118897 118903 102612 102621 102630 102649 118912 118921 102658 118930 102667 118949 118958 118967 118976 118985 102676 118994 119001 119010 119791 119807
3834 (1020) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 38112 (1040) 1234 (1220) 12112 (1240) 12112 (1240) 12112 (1240) 12112 (1240) 12112 (1240) 12112 (1240) 12112 (1240) 581 (1625) 581 (1625) 581 (1625) 581 (1625) 581 (1625) 581 (1625)
Pipe Clamp
34 34
FM Approvals
1-616
Product Designation
Component Description
STABIL GROUP 1232 118277 118286 118295 118301 118310 118329 118338 118620 118639 118648 118657 118666 118675 118684 118693 118709 118718 118727 118736 118745 118754 118763 118772 118781 118790 118806 118198 118204
3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 3 8 (10) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16) 5 8 (16)
34 34
Pipe Clamp
Maximum Working Pressure, psi (kPa)
DK DK
Remarks:
Plan-End Plan-End
a a
a. For use with DIN 2440, 2448 and 2458 (ISO 4200) steel pipe.
FM Approvals
1-617
Component Description
35BC-38 35BC-12
through 4
5 through 8
L E Taylor Associates Ltd, 555 Parkdale Ave N, Hamilton, Ontario L8H 5Y9, Canada
Product Designation Hanger Rod Size, in., NC
3 8 1 2
Component Description
41 41
through 4
5 through 8
Component Description
1 1 1 1 1 2*# 2# 2# 2# 4
Adjustable Clevis Hanger Adjustable Ring Hanger Pipe Clamp Pipe Riser Clamp Side Beam Bracket Angle Bracket 38112 in. (1038 mm) Lag Screw Angle Bracket 122 in. (1351 mm) Lag Screw Side Beam Connector Beam Clamp Loop Hanger
1, 114, 112, 212, 312, 4 5 through 8 4, 5 6 8 212 through 4 5 through 8 4, 5 6 34 through 4 5 through 8 10 and 12
34 through 2 212 through 312 4, 5 6 8 through 12 34 through 4
1 50-51
3 8 1 2
56
3 8
3 4
5 through 8 through 2
56
3 8
212 through 4
3 8
(10)
3 8
3 4 3 4
through 4
3 8 1 2
*The Fig. 2 ring hangers using the polycarbon encased hex nut are FM Approved to support 212 through 4 in. NPS sprinkler system piping only. Uses 162 in. drive screw to support up to 2 in. piping and 123 in. lag screw to support up to 4 in. piping. #Alternate material stainless steel. **These hanger components are also FM Approved when threaded for use with the nearest equivalent standard metric size hanger rod, M10 or M12, as shown. The suffix M appears after the model number for hangers using metric rods.
Tyco Fire and Building Products (Netherlands), Box 198, 7500 AD Enschede, Holland
Product Designation Hanger Rod Size, in. NC Component Description For Nominal Pipe Sizes, in.
90 90 91
3 4 3 4
FM Approvals
1-618
Product Designation
Component Description
91 TCB10& TDM10% UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID UNI-SOLID
02 03 05 06 08 10 12 15 19 22
M12, 13 mm M10 M10 M10* M10* M10* M10* M10* M10 M10 M10 M12 M12
5 through 8 through 2 34 through 2 3 4 1 114 112 2 212 (76.1 mm) 3 4 5 (139.7 mm) 6 (168.3 mm)
3 4
*Minimum threaded rod size allowed per FM Approvals. For European jurisdictions that prefer to use clearance holes for the threaded rod and hex jam nuts to secure the rods to the beam clamps. & Approval limited to minimum allowable steel deck thickness of 0.75 mm and greater with the side punched holes on the steel deck a minimum of 44 mm from the bottom of the steel deck span. % Approval limited to minimum allowable steel deck thickness of 0.75 mm and greater.
AB AB TKN-10* TK-12 TK16 M10 TK16 O 11 TK16 38 TK16 M12 TK16O 13 TK16 12 TK16 M16 TK16O 17 TK16 58
Beam C-Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp Beam Clamp
through 100 mm through 100 mm through 100 mm through 100 mm through 100 mm through 100 mm 34 through 4 in. 20 through 200 mm 20 through 200 mm 34 through 8 in. 20 through 300 mm** 20 through 300 mm** 34 through 12 in.**
20 20 20 20 20 20
*For European jurisdictions that prefer to use clearance holes for the threaded rod and hex jam nuts to secure the rods to the beam clamp. **Approved for use with the set screw on the load side.
J. Van Walraven, Holding B.V., Industrieweg 5, Box 15, 3640 AA Mijrecht, The Netherlands
Product Designation Hanger Rod Size, in., NC
3 8 1 2
Component Description
41 41
through 4
5 through 8
Component Description
Beam C-Clamp Top Beam C-Clamp Wide Throat Top Beam C-Clamp
3 4 3 4
FM Approvals
1-619
FASTENERS
Anchors, expansion shields, concrete inserts, explosive-driven fasteners and threaded head screws provide anchorage to building structural members for supporting pipe hangers. See PIPE HANGER listing for other components and minimum rod sizes. Unless specifically noted in the listing, the following fasteners are FM Approved for vertical installation only.
Expansion Shields
Expansion shields provide anchorage to a concrete building member for supporting pipe hangers.
Adolf Wurth GmbH & Co KG, Postfach 74650, Kunzelsa Germany
Product Designation Hanger Rod Size, mm, NC Component Description For Nominal Pipe Sizes, in.
WED M10* WED M12* WED M16* WED M20 WEZ M10 WEZ M12
10 12 16 10 12
Drop-In Anchor
3 4
3 4
*These expansion shields are available in carbon steel or 316 stainless steel.
10 12 16 10 12 16
3 4
3 4
Remarks
34
through 4
(prefix)-3623 (prefix)-3630 (prefix)-3640 (prefix)-3648 (prefix)-3665 (prefix)-3670 (prefix)-3672 (prefix)-3725 (prefix)-3733 (prefix)-3735 (prefix)-3739 (prefix)-3743 (prefix)-3745 (prefix)-3747 (prefix)-3770 (prefix)-3773 (prefix)-3778 (prefix)-3784 (prefix)-3787 (prefix)-3790 (prefix)-3793 (prefix)-3795
12234 12334 12414 12512 127 12812 1210 58312 58412 585 586 587 58812 5810 34414 34434 34512 34614 347 34812 3410 3412
5, 6, 8
10, 12
10, 12
All anchors are available in zinc plated steel and stainless steel. A Prefix is added to the Part Number, used to designate finish and packaging category. The first 3 digits in the Prefix identified below are for product finish.
FM Approvals
1-620
fischerwerke Artur Fischer GmbH and Co KG, Weinhalde 14-18, D-72178 Waldachtal, Germany
Product Designation Hanger Rod Size, mm Max Nominal Pipe Size, in.
Remarks
EA M10 EA M12 EA M16 EA M20 EA 11 M10 EA 11 M12 EA 11 M16 EA 11 M20 FH 15** FH 18/80** FH 18/100** FH 24** FAZ II FAZ II FAZ II FAZ II FAZ II FZA 1440 M10 FZA 1460 M10 FZA 1880 M12 FZA 22100 M16 FZA 22125 M16 FZA 22125 M16 D/20 FZA 22125 M16 D/25 FZA 1880 M10 I FZA 22100 M12 I FZA 22125 M12 I FZA 1480 M10 D/20 FZA 14x100 M10 D/4 0 FZA 18100 M12 D/20 FZA 18130 M12 D/50 FZEA 1240 M10* FZEA 1440 M12* FZEA II 1240 M10* FZEA II 1440 M12*
10 12 16 20 10 12 16 20 10 12
4 8 12 12 4 8 12 12 4 8
Hammerset Anchor
Hammerset Anchor
12 4 8 12 12 12 4 4 8 12 12 12 12 4 8 8 4 4 8 8 4 4 4 4 Anchor bolt Anchor bolt Anchor bolt Anchor bolt Anchor bolt Zykon Anchor
*These anchors are also FM Approved when threaded for use with the nearest equivalent standard metric or UNC size rod. **Model FH Approved with Bolt, Screw, Cap Nut or Countersink Screw Head.
All anchors are available in zinc plated steel and stainless steel.
FM Approvals
1-621
4 8 12 12
Concrete Anchor
Product Designation
3 3 3 3
4 8 12 12
3 4
Kwik Bolt TZ
through 4
5 through 8
10, 12
10, 12
Remarks
3 3 3 3
4 8 12 12 through 4
Concrete Anchor
Kwik Bolt TZ
Kwik Bolt TZ
5 through 8
Kwik Bolt TZ
10, 12
5/66
58812 5810 34512 348 3410
Kwik Bolt TZ
10, 12
Product Designation
Remarks
10 12 16 10 12 16
4 8 12 4 8 12
Drop In Type
Product Designation
Component Description
Concrete Anchor
34
FM Approvals
1-622
Product Designation
Component Description
HDI-L 12 HDI-P 38
through 8 through 4
3 8
34
through 4
3 8
3 8 1 2 5 8 3 4
4 8 8 12
Red Head Sleeve Anchor. HN-1222, -1230, -1240, -3817, -3830 HN-5822, -5830, -5842, -5860 HN-3424, -3440, -3462 SHN-3817, -3830 SHN-1222, -1240 SHN-5830, -5842
3 8 1 2 5 8 3 8 1 2 5 8
34-4
5-8 12
34-4
5-8 10-12
Red Head Wedge Anchor. WS-3822, -3826, -3830, -3836, -3850 WS-1226, -1236, -1242, -1254, -1270 WS-5834, -5842, -5850, -5860, -5870, -5884 WS-3446, -3454, -3470, -3484, -34100, -3442, -3462 WS-1226G, -1242G, -1254G, -1270G WS-5834G, -5860G WS-3446G, -3454G, -3484G WW-3822, -3826, -3830, -3836, -3850 WW-1226, -1236, -1242, -1254, -1270 WW-5834 WW-5850, -5860, -5870 WW-3446, -3454, -3470, -3484, -34100 SWW-3826, -3836 SWW-1226, -1242 SWW-5850 SWW-3446, -3454
3 8 1 2 5 8 3 4 1 2 5 8 3 4 3 8 1 2 5 8 5 8 3 4 3 8 1 2 5 8 3 4
34-4
5-8 10, 12 10, 12 5-8 10, 12 10, 12 34-4 5-8 10, 12 10, 12 10, 12 34-4 5-8 10, 12 10, 12
Min 358 in. (92 mm) Embedment 303 stainless steel 316 stainless steel Min 358 in. (92 mm) Embedment 316 stainless steel
Red Head Multi-Set II Flange Anchor. RM-38 RM-12 RM-58 RM-34 SRM-38 SRM-12 SRM-58
3 8 1 2 5 8 3 4
34-4
5-8 12 12
34-4
3 8 1 2 5 8
5-8 10, 12
Remarks
Sup-R-Sleeves
through 4
Sup-R-Stud
3 4
through 4
FM Approvals
1-623
Product Designation
Remarks
5-8
10, 12
Sup-R-Drop
3 8 1 2 3 4
34
through 4 5, 6, 8 10, 12
MKT-Metall-Kunststoff-Technik GmbH & Co KG, Auf dem Immel 2, D-67685 Weilerbach, Germany
Product Designation Hanger Rod Size, mm Component Description For Nominal Pipe Sizes, in.
3 4
EM10* EM12* EM16* EM20* BZ Plus 10* BZ Plus 12* BZ Plus 16* B-10* B-12* B-16*
M10 M12 M16 M20 M10 M12 M16 M10 M12 M16
*These expansion shields are available in carbon steel or 316 stainless steel. These anchors are also FM Approved when threaded for use with the nearest equivalent standard UNC size rod.
Remarks
PIPE SPIKE 3758 LOK-BOLT Series 5000 5815 5825 5840 STEEL DROPIN 6206 6208 6210 6212 STEEL DROPIN 6226 6228 6230 6232 STEEL DROPIN Series 6300 6306 6308 6310 6312 MINI DROPIN 6322 SNAKE ANCHOR 6401
3 8 1 2 5 8
4 8 12
3 8 1 2 5 8 3 4
4 8 12 12
3 8 1 2 5 8 3 4
4 8 12 12
3 8 1 2 5 8 3 4 3 8
4 8 12 12 4
3 8
FM Approvals
1-624
Product Designation
Remarks
10mm
3 8 1 2 5 8
4 8 12
POWER-BOLT Series 6900 6910 6911 6912 6913 6914 6916 6930 6931 6932 6933 6934 6935 6936 6940 6941 6942 6943 6944 6945 6946 6947 6950 6951 6952 6953 6954 6955 6956 6957 SET-BOLT Series 7100 7123 7126 7129 7134 7145 7151 7153 7168 7172 7176 7189 7194 7196 SET-BOLT (METRIC) Series 61000 61050 61052 POWER-STUD Series 7300 7310 7312 7313 7314 7315 7316 7320 7322 7323 7324 7326 7330
3 8 3 8 3 8 3 8 3 8 3 8 1 2 1 2 1 2 1 2 1 2 1 2 1 2 5 8 5 8 5 8 5 8 5 8 5 8 5 8 5 8 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
4 4 4 4 4 4 8 8 8 8 8 8 8 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
3 8 3 8 3 8 3 8 1 2 1 2 1 2 5 8 5 8 5 8 3 4 3 4 3 4
Stud anchor
4 4 4 4 8 8 8 12 12 12 12 12 12
10mm 12mm
4 8
3 8 3 8 3 8 3 8 3 8 3 8 3 8 3 8 3 8 3 8 3 8 1 2
4 4 4 4 4 4 4 4 4 4 4 8
FM Approvals
1-625
Product Designation
Remarks
7332 7333 7334 7336 7338 7342 7344 7346 7348 7349 POWER-STUD Series 7400 7412 7413 7414 7415 7416 7417 7420 7422 7423 7424 7426 7427 7430 7432 7433 7434 7436 7438 7439 7440 7441 7442 7444 7446 7448 7449 7451 7450 7452 7454 7461 7463 7465 POWER-STUD Series 7600 7610 7612 7613 7614 7615 7616 7620 7622 7623 7624 7626 7630 7632 7633 7634 7636 7638 7642 7644 7646 7648 POWER-STUD Series 7700 7720 7723 7724
8 8 8 8 8 12 12 12 12 12
3 8 3 8 3 8 3 8 3 8 3 8 1 2 1 2 1 2 1 2 1 2 1 2 5 8 5 8 5 8 5 8 5 8 5 8 5 8 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 7 8 7 8 7 8
1 1 1
4 4 4 4 4 4 8 8 8 8 8 8 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
3 8 3 8 3 8 3 8 3 8 3 8 1 2 1 2 1 2 1 2 1 2 5 8 5 8 5 8 5 8 5 8 5 8 3 4 3 4 3 4 3 4
4 4 4 4 4 4 8 8 8 8 8 12 12 12 12 12 12 12 12 12 12
1 2 1 2 1 2
8 8 8
FM Approvals
1-626
Product Designation
Remarks
7726 7730 7734 7741 7742 7748 7750 7752 7763 7765 POWER-STUD Series 7800 7806 7808 7810 7812 DRIVE ANCHOR Series 3000 3633 3663 3693 3723 3813 3843
1 1
8 12 12 12 12 12 12 12 12 12
3 8 1 2 5 8 3 4
4 8 12 12
3 8 3 8 3 8 3 8 1 2 1 2
4 4 4 4 8 8
Remarks
DIA37 DIA50 DIA62 DIA75 DIA50C DIA75C DIAL37 DIAL50 DIAL62 DIAL75 DIA37S SL37178C SL50214C SL62214C SL37178H SL37178H SL37300H SL37400H SL50214H SL50300H SL50400H SL50600H SL62214H SL62300H SL62414H SL62600H SL75214H
4 8 12 12 8 12 4 8 12 12 4 4 8 12 4 4 4 4 8 8 8 8 12 12 12 12 12
Drop-In Anchor
Drop-In Anchor-Coil Thread Drop-In Anchor, with Lip Short Drop-In Anchor
2 1
Sleeve-All Sleeve Anchor Coil Thread 1 Sleeve All Sleeve Anchor Hex Head 1
FM Approvals
1-627
Product Designation
Remarks
SL75414H SL75614H SL37234PF SL37400PF SL37500PF SL37600PF SL37212R SL37334R SL37434R WA37214 WA37234 WA37300 WA37312 WA37334 WA37500 WA37700 WA50234 WA50334 WA50414 WA50512 WA50700 WA50812 WA50100 WA50120 WA62312 WA62412 WA62500 WA62600 WA62700 WA62812 WA62100 WA62120 WA75414 WA75434 WA75512 WA75614 WA75700 WA75812 WA75100 WA75120 WA87600 WA87800 WA87100 WA87120 WA16000 WA19000 WA11200
12 12 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 8 8 8 8 8 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
Sleeve-All Sleeve Anchor Philips Head 1 Sleeve-All Sleeve Anchor Round Head 1 Wedge-All Wedge Anchor
3
1 1 1
FM Approvals
1-628
Product Designation
Remarks
114 1 1 4 1 1 2
12 12 12
Available in stainless steel and zinc plated carbon steel. Available in zinc plated carbon steel. Available in stainless steel and zinc plated or mechanically galvanized carbon steel anchors.
Remarks
Spitfix Spitfix Spitfix Spitfix Spit Grip SA Spit Grip SA Spit Grip SA Spit Grip Spit Grip Spit Grip L Spit Grip L FIX II FIX II A4 (Stainless steel version) FIX Z* FIX Z A4 (Stainless steel version)
*This version is available in zinc coated steel.
M10 M12 M16 M20 M10 M12 M16 M10 M12 M10 M12 M10 M10
through 8 5 to 6 8 10 to12
Non-drilling anchor, Metric thread Drop-In Anchor, Metric thread Drop-In Anchor Drop-In Anchor Stud Anchor Stud Anchor
3 4
3 4
3 4
3 4 3 4
M10 M10
3 4 3 4
through 4 through 4
Storring and Bruckmann GmbH, Postfach 150425, 42523 Velbert Neviges, Germany
Product Designation Hanger Rod Size, mm Component Description For Nominal Pipe Size, in. (mm)
34 through 4 (20 through 100)
Subex M10
10
Drop-in Anchor
Subex M12
12
Drop-in Anchor
5 through 8 (125 through 200) 10 through 12 (250 through 300) 10 through 12 (250 through 300)
Subex M16
16
Drop-in Anchor
Subex M20
20
Drop-in Anchor
UCAN Fastening Products, 155 Champagne Drive, Unit 10 Toronto, Ontario M3J 2C6, Canada
Product Designation Hanger Rod Size, mm
3 8 3 8 1 2 1 2 5 8 5 8
Remarks
IPA 3812* IPS 3812** IPA 1258* IPS 1258** IPA 5858* IPS 5858**
5 5 5 5
*These anchors are available in zinc plated steel. **These anchors are available in 304 Stainless Steel.
FM Approvals
1-629
Concrete Inserts
Concrete inserts provide anchorage to concrete building structures for supporting pipe hangers. Concrete inserts must be installed when the building is constructed.
Anvil International Inc, 110 Corporate Drive, Suite 10, Portsmouth NH 03801
Fig. Fig. Fig. Fig. 152. 281. 282. 285.
38, 12, 58, 34, 78 3 4
in. (10, 13, 16, 19, 22 mm) rods. through 8 in. NPS (19 through 203 mm). 34 through 8 in. NPS (19 through 203 mm). 34 through 5 in. NPS (19 through 127 mm).
Empire Industries Inc, 180 Olcott St, Box 1020, Manchester CT 06045-1020
Fig. 81. Concrete insert with Fig. 81-N nuts. 38 in. (10 mm) nut. 34 through 4 in. NPS (19 through 102 mm). 12 in. (13 mm) nut. 5, 6, 8 in. NPS (127, 152, 203 mm).
Globe Pipe Hanger Products Inc, 14601 Industrial Pkwy, Cleveland OH 44135
Type 726-106. Concrete insert with Type 725 nuts 725-103 38 nut, 34 through 4 in. NPS 725-104 12 nut, 5 through 8 in. NPS 725-105 58 nut 10 through 12 in. NPS 725-106 34 nut 10 through 12 in. NPS
Component Description
PIP-143812
PIP-143812
1 2
PIP-381258
3 8
PIP-381258
1 2
SDI-143812
3 8
SDI-143812
3 8
SDI-143812
1 2
SDI-381258
3 8
SDI-381258
1 2
SDI-5834
5 8
SDI-5834
3 4
Wood form insert. Cast-in-Place Anchor, Normal Weight concrete with wood form Wood form insert. Cast-in-Place Anchor Normal Weight concrete with wood form Wood form insert. Cast-in-Place Anchor, Normal Weight concrete with wood form Wood form insert Cast-in-Place Anchor, Normal Weight concrete with wood form Metal deck insert. Cast-in Place Anchor, Lightweight concrete over steel deck in the Lower Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Metal deck insert. Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute
through 4
5 through 8
3 4
through 4
5 through 8
3 4
through 4
3 4
through 4
5 through 8
3 4
through 4
5 through 8
10 and 12
10 and 12
The description of the product designation is the following: PIP Wood Form Insert SDI Metal Deck Insert
FM Approvals
1-630
Component Description
Cast in Anchor concrete with wood forms Cast in Anchor concrete with wood forms Cast in Anchor concrete over steel deck (Upper and Lower Flute) Cast in Anchor concrete over steel deck (Upper Flute) Cast in Anchor concrete over steel deck (Upper Flute) Cast in Anchor concrete over steel deck (Upper Flute)
3 4 3 4 3 4 3 4 3 4 3 4
3 8 1 2 5 8
Concrete over steel deck (Upper & Lower Flute) Concrete over steel deck (Upper Flute) Concrete over steel deck (Upper Flute)
4 8 12
3 8
Component Description
BBMD2550
3 8
BBMD2550
1 2
BBMD3762
3 8
BBMD3762
1 2
BBMD6275
5 8
BBMD6275
3 4
Cast-in-Place Anchor, Normal Weight concrete with wood form Cast-in-Place Anchor, Normal Weight concrete with wood form Cast-in-Place Anchor, Normal Weight concrete with wood form Cast-in-Place Anchor, Normal Weight concrete with wood form Cast-in Place Anchor, Lightweight concrete over steel deck in the Lower Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute Cast-in-Place Anchor, Lightweight concrete over steel deck in the Upper Flute
through 4
5 through 8
3 4
through 4
5 through 8
3 4
through 4
3 4
through 4
5 through 8
3 4
through 4
5 through 8
10 and 12
10 and 12
The description of the product designation is the following: BBWF Blue Banger Wood Form BBMD Blue Banger Metal Deck
FM Approvals
1-631
Storring and Bruckmann GmbH, Postfach 150425, 42523 Velbert Neviges, Germany
Subex Concrete Anchors M10 M10 M12 M16 M20 (38 ( 3 8 ( 1 2 (58 (34 in.) in.) in.) in.) in.) nominal nominal nominal nominal nominal size size size size size
34 34
through 4 in. pipe. through 4 in. pipe. 5 through 8 in. pipe. 10 through 12 in. pipe. 10 through 12 in. pipe.
Remarks
through 4
4 through 8
Unistrut Corp dba Unistrut Diversified Products, 35660 Clinton St, Wayne MI 48184
Cat. Nos. M24, M26. Cat. Nos. P3249-70 inclusive. Cat. Nos. P3349-70 inclusive. All nuts are available with or without springs.
Explosive-Driven Fasteners
Explosive-driven fasteners provide anchorage to concrete or steel building members for supporting pipe hangers. The powder-actuated tool used for driving these fasteners may represent an ignition source; therefore, it should not be used in classified hazardous locations or near easily ignited materials. Fasteners should not be used for support of pipe hangers to structural members in Earthquake Zones 500 or less as defined by FM Global Property Loss Prevention Data Sheet 1-2. A coupling and locknut are provided with each fastener for attaching a pipe hanger to the fastener.
Hilti Inc, 5400 S 122nd East Ave, Tulsa OK 74146
Fastener, Cat. No. Coupling, Cat. No. For Use In Max Pipe Size, in. (mm)
W10-30-27P10 W10-30-27P10 W10-30-27P10 W10-30-32P10 W10-30-32P10 W10-30-32P10 W10-30-42P10 W10-30-42P10 W10-30-42P10 W10-30-47P10 W10-30-47P10 W10-30-47P10 EW10-30-15P10 EW10-30-15P10 EW10-30-15P10
D1025 ACI-F ACI-H D1025 ACI-F ACI-H D1025 ACI-F ACI-H D1025 ACI-F ACI-H D1025 ACI-F ACI-H
Concrete Steel
2 (51) 312 (89) 5 (127) 2 (51) 312 (89) 5 (127) 2 (51) 312 (89) 5 (127) 2 (51) 312 (89) 5 (127) 2 (51) 312 (89) 5 (127)
For Use In
FM Approvals
1-632
For Use In
X-EW6H-28-9 FP8 X-EW6H-28-9 P12 X-EW6H-38-9 FP8 X-EW6H-38-9 P12 X-EW10H-30-14 P10
These fasteners are also FM Approved for horizontal installation. Max pipe size 312 in. (89 mm).
For Use In
Concrete
3 8 3 8 3 8
5 5 5
Screws
Threaded head screws provide anchorage to concrete, steel or wood building structural members for supporting pipe hangers. Fasteners should not be used for support of pipe hangers to structural members in Earthquake Zones 500 or less as defined by FM Global Property Loss Prevention Data Sheet 1-2.
ITW Buildex Corp, 1349 West Bryn Mawr Ave, Itasca IL 60143
Product Designation Hanger Rod Size, in.
3 8 3 8 3 8 38 3 8 3 8 3 8 3 8 3 8 3 8 38 3 8 3 8 3 8 3 8 3 8 3 8
Component Description
DST 516 TEK 50 DSTR-1 DSTR-112 DSTR 516 SH DSTR1 XP 20 XP 35 SWDR1 SWDR 516 SWDR 112 SH GST20 SH GST30 GST 20 GST 30 CST 20 SWC20
Product Designation
Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded
Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head
Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw
for for for for for for for for for for for for for for for for for
use use use use use use use use use use use use use use use use use
in in in in in in in in in in in in in in in in in
steel I beams steel I beams steel I beams and steel I beams and steel I beams and steel I beams and 12 gage purlins 12 gage purlins 16 gage purlin 16 gage purlin 16 gage purlin Wood Wood Wood Wood Concrete Concrete
12 12 12 12
3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
through through through through through through through through through through through through through through through through through
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
Component Description
DST 516 M10 TEK 50 M10 DSTR-1 M10 DSTR-112 M10 DSTR 516 M10 SH DSTR1 M10 XP 20 M10 XP 35 M10 SWDR 1 M10 SWDR 516 M10 SWDR 112 M10 SH GST20 M10 SH GST30 M10 GST 20 M10 GST 30 M10 CST 20 M10 SWC20 M10
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded Threaded
Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head Head
Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw
for for for for for for for for for for for for for for for for for
use use use use use use use use use use use use use use use use use
in in in in in in in in in in in in in in in in in
steel I beams steel I beams steel I beams and steel I beams and steel I beams and steel I beams and 12 gage purlins 12 gage purlins 16 gage purlin 16 gage purlin 16 gage purlin Wood Wood Wood Wood Concrete Concrete
12 12 12 12
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
through through through through through through through through through through through through through through through through through
100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100
FM Approvals
1-633
Elco Fastening Systems LLC, Falcon Road Operation, 5110 Falcon Road, Rockford IL 61109
Product Designation Hanger Rod Size, in., NC
38 38 38 38 38 38 38 38 38 38 38 38
Component Description
ZG471 with backing nut ZG491 with backing nut ZG511 with backing nut ZG470 ZG471 with backing nut ZG490 ZG550 ZG510 ZG730 ZG650 ZG660 ZG670
Product Designation
Threaded Head Screw for uses in and purlins 16 gage and thicker Threaded Head Screw for uses in and purlins 16 gage and thicker Threaded Head Screw for uses in and purlins 16 gage and thicker Threaded Head Screw for uses in and purlins 12 gage and thicker Threaded Head Screw for uses in and purlins 16 gage and thicker Threaded Head Screw for uses in and purlins 12 gage and thicker Threaded Head Screw for uses in Threaded Head Screw for uses in Threaded Head Screw for uses in Threaded Head Screw for uses in Threaded Head Screw for uses in Threaded Head Screw for uses in
Component Description
steel beams steel beams steel beams steel beams steel beams steel beams steel beams steel beams concrete wood beams wood beams wood beams
3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4
through 4 through 4 through 4 through 4 through 4 through 4 through through through through through through 4 4 4 4 4 4
10 10 10
Threaded Head Screw for uses in steel beams Threaded Head Screw for uses in wood beams Threaded Head Screw for uses in concrete
VERTIGO Series 7100 7173 7175 7162 7161 7158 7154 7160 7184 7186 7201 7188
3 8 1 2 3 8 1 2 3 8 3 8 3 8 3 8 3 8 3 8 3 8
Concrete drilled insert (vertical only) Concrete drilled insert (vertical only) Wood Beams (vertical only) Steel Beams (14 thick) Steel Purlins (12 gage minimum) and Steel Beams (vertical mount) Steel Purlins (12 gage minimum) and Steel Beams (vertical mount) Steel Purlins (12 gage minimum) and Steel Beams (vertical mount) Steel Purlins (12 gage minimum) (horizontal mount) Steel Purlins (12 gage minimum) (horizontal mount) Steel Purlins (12 gage minimum) (horizontal mount) Steel Purlins (12 gage minimum) (horizontal mount)
4 8 4 8 4 4 4 4 4 4 4
VERTIGO (METRIC) Series 28000 28084 28038 28008 28010 28100 28102
Concrete drilled insert (vertical only) Steel Beams (6.3mm thick minimum) Steel Purlins (2.7mm minimum) and Steel Beams (vertical mount) Steel Purlins (2.7mm minimum) and Steel Beams (vertical mount) Steel Purlins (2.7mm minimum) (horizontal mount) Steel Purlins (2.7mm minimum) (horizontal mount)
4 8 4 4 4 4
Remarks
4 4 4 4 8
FM Approvals
1-634
Product Designation
Remarks
THD50400H THD50500H THD50600H THD50612H THD50800H THD501100H THD501200H THD501300H THD501400H THD501500H THD62500H THD62600H THD62612H THD62800H THD75500H THD75600H THD75700H THD37500HMG THD37600HMG THD50612HMG THD50800HMG THD62600HMG THD62612HMG THD62800HMG
*Available in zinc plated carbon steel.
8 8 8 8 8 8 8 8 8 8 12 12 12 12 12 12 12 4 4 8 8 12 12 12
POWDER-ACTUATED TOOLS
Powder-actuated tools utilize expanding gases from a power load to drive a fastener into masonry, concrete or steel. Use of these tools shall be in strict conformance with the manufacturers recommended procedures. These tools are divided into two types: direct-acting, in which the expanding gas of the power load acts directly on the fastener to be driven and indirect-acting, in which the expanding gas of the power load acts on a captive piston which in turn drives the fastener. These tools have three velocity classifications: low, medium and high. Powder-actuated tools are tested by FM Approvals, FM Approved and listed in strict conformance with the American National Standard Safety Requirements for Powder-Actuated Fastening Systems: ANSI A10-1970, ANSI A10-1972 and ANSI A10-1977, and also the Federal Register, Occupational Safety and Health Administration (OSHA), Volume 37, No. 202 and Title 29, Part 1910.
ITW Buildex Corp, 1349 W Bryn Mawr Ave, Itasca IL 60143
Model BX900. .25 caliber, semi-automatic, low velocity, indirect acting, piston type. For use with Model BX 14 fasteners in steel or concrete building structural members.
Power Load No. Power Level Color Code Cartridge Material
4 5 6
Model UNIDEK. .25 caliber, multi-shot, low velocity, indirect acting, piston type. For use with Model BX 14 fasteners in steel or concrete building structural members.
1283900 1281900 1282900 4 5 6 Yellow Red Purple Brass Brass Brass
FM Approvals
1-635
Accelerators and Exhausters Accelerators with Built-In Antiflooding Device Adjustable Sprinkler Fittings Air Drying Units Air Pressure Maintenance Devices, Special Sprinkler Systems Antiflooding Devices for Accelerators Automatic Releases for Preaction and Deluge Sprinkler Systems Automatic Water Control Valves Automatic Water Control Valves (Table) Backflow Preventers Double Check Detector Check Type Double Check Type Reduced Pressure Principle Detector Check Type Reduced Pressure Principle Type Ball Drips Branch Line Testers Check Valves, Anti-Water Hammer Control Mode Sprinklers Control Mode (Specific Application), Cooling Tower Automatic Sprinklers, Control Mode (Specific Application), Cooling Tower (Class 2019) Open Sprinklers, Control Mode (Specific Application) Window and Cornice Open Sprinklers, Control Mode (Specific Application) Window and Cornice (Class 2014) K2.8 Standard Spray Sprinklers K2.8 Flush, Recessed and Concealed (Class 2015) K2.8 Flush, Recessed and Concealed (Pendent) K2.8 Pendent (Class 2002) K2.8 Pendent, Quick Response (Class 2020) K2.8 Upright (Class 2002) K2.8 Upright, Quick Response (Class 2020) K5.6 Corrosion Resistant (Stainless Steel) K5.6 Stainless Steel, Pendent (Class 2042) K5.6 Stainless Steel, Pendent, Quick Response (Class 2020) K5.6 Stainless Steel, Upright (Class 2042) K5.6 Stainless Steel, Upright Quick Response (Class 2020) K5.6 Dry, Flush, Recessed and Concealed (Pendent or Sidewall) K5.6 Dry Flush, Recessed and Concealed (Class 2015) K5.6 Dry Flush, Recessed and Concealed, Quick Response (Class 2020) K5.6 Dry K5.6 Dry Pendent (Class 2013) K5.6 Dry Pendent, Quick Response (Class 2020) K5.6 Dry Sidewall (Class 2013) K5.6 Dry Sidewall, Quick Response (Class 2020) K5.6 Dry Upright (Class 2013) K5.6 Dry Upright Quick Response (Class 2020) K5.6 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent or Sidewall) Extended Coverage Light Hazard (ECLH) Flush, Recessed and Concealed (Class 2022) Extended Coverage Light Hazard (ECLH) Flush, Recessed and Concealed, Quick Response (Class 2020) K5.6 Extended Coverage Light Hazard (ECLH) (Pendent or Sidewall) Extended Coverage Light Hazard (ECLH) K5.6 Pendent (Class 2022) Extended Coverage Light Hazard (ECLH) K5.6 Pendent, Quick Response (Class 2020) Extended Coverage Light Hazard (ECLH) K5.6 Sidewall (Class 2022) Extended Coverage Light Hazard (ECLH) K5.6 Sidewall, Quick Response (Class 2020) K5.6 Flush, Recessed and Concealed (Pendent or Sidewall) K5.6 Flush, Recessed and Concealed (Class 2015) K5.6 Flush, Recessed and Concealed, Quick Response (Class 2020) K5.6 Sidewall Flush, Recessed and Concealed (Class 2015) K5.6 Sidewall Flush, Recessed and Concealed, Quick Response (Class 2020) K5.6 High Temperature Oven K5.6 High Temperature Oven, Pendent (Class 2017) K5.6 High Temperature Oven, Upright (Class 2016) K5.6 Rack Storage K5.6 Rack Storage, Pendent (Class 2005) K5.6 Rack Storage, Pendent, Quick Response (Class 2020) K5.6 Rack Storage, Upright (Class 2005) K5.6 Rack Storage, Upright, Quick Response (Class 2020) K5.6 Standard Sidewall K5.6 Sidewall (Class 2012) K5.6 Sidewall, Quick Response (Class 2020) K5.6 Standard Spray Sprinklers K5.6 Pendent (Class 2017) K5.6 Pendent, Quick Response (Class 2020) K5.6 Upright (Class 2016) K5.6 Upright, Quick Response (Class 2020)
FM Approvals
1-636
K5.6 Wax Coated High Temperature K5.6 Wax Coated, High Temperature, Pendent (Class 2043) K5.6 Wax Coated, High Temperature, Upright (Class 2043) Wax Coated, High Temperature, Sidewall (Class 2043) K8.0 Corrosion Resistant (Stainless Steel) K8.0 Stainless Steel, Pendent (Class 2042) K8.0 Stainless Steel, Pendent Quick Response (Class 2020) K8.0 Stainless Steel, Upright (Class 2042) K8.0 Stainless Steel, Upright, Quick Response (Class 2020) K8.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent or Sidewall) K8.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Class 2022) K8.0 Extended Coverage Light Hazard (ECLH), Flush Recessed and Concealed, Quick Response (Class 2020) K8.0 Extended Coverage Light Hazard (ECLH) K8.0 Extended Coverage Light Hazard (ECLH), Pendent (Class 2022) K8.0 Extended Coverage Light Hazard (ECLH), Pendent, Quick Response (Class 2020) K8.0 Extended Coverage Light Hazard (ECLH), Sidewall (Class 2022) K8.0 Extended Coverage Light Hazard (ECLH), Sidewall, Quick Response (Class 2020) K8.0 Flush, Recessed and Concealed (Pendent) K8.0 Dry Flush, Recessed and Concealed (Class 2015) K8.0 Dry, Flush, Recessed and Concealed (Pendent or Sidewall) K8.0 Dry Flush, Recessed and Concealed, Quick Response (Class 2020) K8.0 Flush, Recessed and Concealed (Class 2015) K8.0 Flush, Recessed and Concealed, Quick Response (Class 2020) K8.0 High Temperature Oven K8.0 High Temperature Oven (Class 2001) K8.0 Rack Storage K8.0 Rack Storage, Pendent (Class 2005) K8.0 Rack Storage, Pendent, Quick Response (Class 2020) K8.0 Rack Storage, Upright (Class 2005) K8.0 Rack Storage, Upright, Quick Response (Class 2020) K8.0 Standard Spray Sprinklers K8.0 Dry Pendent (Class 2013) K8.0 Dry Pendent, Quick Response (Class 2020) K8.0 Dry Upright (Class 2013) K8.0 Dry Upright Quick Response (Class 2020) K8.0 Pendent (Class 2001) K8.0 Pendent, Quick Response (Class 2020) K8.0 Upright (Class 2001) K8.0 Upright, Quick Response (Class 2020) K8.0 Wax Coated, High Temperature K8.0 Pendent, Wax Coated, High Temperature (Class 2043) K8.0 Upright, Wax Coated, High Temperature (Class 2043) K11.2 Control Mode (Density/Area) K11.2 Pendent (Class 2009) K11.2 Pendent, Quick Response (Class 2020) K11.2 Upright (Class 2009) K11.2 Upright, Quick Response (Class 2020) K11.2 Control Mode (Specific Application) K11.2 Control Mode (Specific Application) Upright (Class 2007) K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent) K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed Types (Class 2022) K11.2 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed Types, Quick Response (Class 2020) K11.2 Extended Coverage Light Hazard (ECLH) K11.2 Extended Coverage Light Hazard (ECLH) Pendent (Class 2022) K11.2 Extended Coverage Light Hazard (ECLH) Pendent, Quick Response (Class 2020) K11.2 Extended Coverage Ordinary Hazard (ECOH) 11.2 ECOH Pendent (Class 2022) 11.2 ECOH Upright (Class 2022) K11.2 Wax Coated, High Temperature K11.2 Wax Coated, High Temperature, Pendent (Class 2043) Wax Coated, High Temperature, Upright (Class 2043) K14.0 Control Mode (Density/Area) K14.0 Pendent (Class 2023) K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Pendent) K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed (Class 2015) K14.0 Extended Coverage Light Hazard (ECLH), Flush, Recessed and Concealed, Quick Response (Class 2020) K14.0 Extended Coverage Light Hazard (ECLH) K14.0 Extended Coverage Light Hazard (ECLH), Pendent (Class 2023) K14.0 Extended Coverage Light Hazard (ECLH), Pendent, Quick Response (Class 2020) K14.0 Extended Coverage Metal Building K14.0 Extended Coverage Metal Building Horizontal Sidewall (Class 2033) K14.0 Extended Coverage Ordinary Hazard (ECOH) 14 ECOH Pendent (Class 2022) 14 ECOH Upright (Class 2022)
FM Approvals
1-637
K16.8 Control Mode (Density/Area) K16.8 Upright (Class 2024) K16.8 Control Mode (Specific Application) K16.8 Control Mode (Specific Application) Upright (Class 2007) K25.2 Control Mode, Extended Coverage K25.2 Extended Coverage Upright (Class 2022) Residential Mode Sprinklers Automatic Sprinklers, Residential Mode (Class 2030) Residential Sprinkler Minimum Flow Requirements Sprinkler Guards/Shields Sprinkler Guards/Shields (Class 2091) Suppression Mode Sprinklers K14.0 Suppression Mode [ESFR] K14.0 ESFR Pendent (Class 2008) K14.0 ESFR Upright (Class 2008) K16.8 Suppression Mode [ESFR] K16.8 ESFR Pendent (Class 2027) K16.8 ESFR Upright (Class 2027) K22.4 Suppression Mode [ESFR] K22.4 ESFR Pendent (Class 2028) K25.2 Suppression Mode [ESFR] K25.2 ESFR Pendent (Class 2026) Deluge Sprinkler Systems Dry Pipe Valves Fasteners Concrete Inserts Expansion Shields Explosive-Driven Fasteners Screws Fire Service Connections Fire Service Meters Fixed Sprinkler Fittings Flexible Sprinkler Hose with Fittings for Cleanroom Ceilings Flexible Sprinkler Hose with Fittings for Commercial Suspended Ceilings Flexible Sprinkler Hose with Fittings for Ducts Grooved Couplings Couplings or Fittings, Side Outlet, Flexible Couplings or Fittings, Side Outlet, Rigid Grooved Couplings, Reducing Flexible Grooved Couplings, Standard Flexible Grooved Couplings, Standard Rigid Grooved Split Flanges Flexible Hubless Pipe Couplings Indicating Valves, Butterfly or Ball Type Indicator Posts Inside Screw Gate Valves On-Off Multicycle Sprinkler Systems Outside Screw and Yoke Gate Valves Pipe Fittings Sprinkler Pipe Assemblies Pipe Hangers Plastic Pipe and Fittings Cast Iron Pipe Fittings Ductile Iron Pipe and Fittings Fiber Reinforced Composite Pipe and Fittings Fire Resistant Barriers for Use with CPVC Pipe and Fittings in Light Hazard Occupancies In-Building Risers Pipe, Fittings and Pipe Joints for Underground Fire Service Mains Polyethylene Pipe and Fittings Polyvinyl Chloride (PVC) Pipe and Fittings Post Indicator Valve Assemblies, Butterfly Type Powder-Actuated Tools Preaction Sprinkler Systems Pressure Gauges Pressure Maintenance Devices, Dry Pipe Systems Quick Opening Valves Refrigerated Area Sprinkler Systems Riser Manifold Assemblies Sight Drains Single Check Valves Spare Sprinkler Cabinets Sprinkler System Alarm Testers
FM Approvals
1-638
Steel Pipe Lightwall Pipe Non-threadable Non-schedule Normal connections welded, rolled groove or plain end Schedule 10 Normal connections are welded, rolled groove, or plain end Schedule 40 Normal connections are threaded, welded, rolled or cut groove, or plain end Schedule 5 Non-threadable Lightwall Pipe Normal connections welded, Press-Fit, limited Approval of rolled groove Thinwall Pipe Non-schedule Normal connections are threaded, welded, rolled groove or plain end Schedule 80 Normal connections are threaded, welded, rolled or cut groove, or plain end Suction Pressure Regulating Valves for Booster Pumps Surge and Waterhammer Arresters Telescoping Sprinkler Assemblies for Use in Anechoic Chambers Testers for Vane Type Waterflow Detectors Water Motor Gongs Waterflow Alarm Valves Waterflow Detector Check Valves Waterflow Detectors, Vane Type Trim Water Pressure Relief Valves (Adjustable) Trim Water Pressure Relief Valves (Fixed)
FM Approvals