Академический Документы
Профессиональный Документы
Культура Документы
ROPE RESCUE:
Basic Systems
Webbing Webbing used in rope rescue is also made of nylon and comes in two sizes, 1 and 2 inch. 1 inch is usually used for anchor construction as it fits easily in to carabiners. 2 inch is mainly used any time it comes in to contact with the body as it spreads out the force imparted to the body and makes it more comfortable. For these reasons, 2 inch webbing should be used for all harnesses and stokes basket lashings.
Harnesses used for rope rescue can be tied out of 2 inch webbing or can be commercially sewn harnesses. Either type of harness should be snug fitting around the waist and leg loops.
Cordage is small diameter rope that is used for a variety of purposes. Its most common use is to construct prusik loops. Prusik loops are usually small diameter cordage (also called Perlon, a trade name) tied in to a loop with a double fishermans knot. These loops are attached to a main line rope with a prusik knot to create a rope grab. These rope grabs are used in a variety of situations and are often doubled up when used with a prusik minding pulley. When doubling up prusiks, cordage should be cut in 55 and 60 lengths so that the tied prusik loops will grab the rope evenly and share the load.
Hardware Carabiners (also called D rings, snap links and biners) are used to connect knotted rope to other ropes, hardware, or software. They are made out of aluminum or steel alloy and are incredibly strong. The bulk of the strength is borne by the spine or bar opposite the gate of the carabiner. The carabiner is locked by screwing the collar down the gate until it covers its notch. Whenever possible, the carabiners should be oriented locking down so that any vibration of the carabiner will not unlock or unscrew the locking collar.
.
Tensionless tree wrap shown from above and side. Safety knot omitted for clarity. A carabiner may be used to connect the figure 8 knot to the standing part of the rope if available.
At the carabiner, attach a friction device such as a figure 8 descender or rappel rack. Tie a figure 8 knot at the end of the rope and lace the friction device as shown below.
Single line lowering system. Note webbing sling used for anchor.
Attach the figure 8 knot to the harness of the rescuer to be lowered. Conduct a visual and load test in a safe location before lowering the rescuer over the edge. This method of lowering allows the rescuer to use both hands when negotiating the edge and any obstacles they might encounter. If the rescuer needs the friction device to be locked off so that they may work on a situation, lock off the figure 8 descender as described in the rappelling section. Once the rescuer is in a safe location and requests to come off belay, unlace the figure 8 descender and retrieve the rope to use for the next rescuer. If the next rescuer must descend and there are no other rescuers available for belaying. Unlace the figure 8 and re-rig the anchor for rappelling as shown in the next section.
Rappelling
When selecting a site to rappel from, pay careful attention to the condition of the edge so that it is free from obstructions and loose material. Rig a suitable anchor with a webbing sling or tensionless tree wrap and attach a carabiner to the end of the anchor rig. Tie a figure 8 knot in to the end of a rope, attach it to the carabiner and carefully lower the remainder of the rope over the edge.
In a safe location lace the figure 8 descender and attach it to the rescuers harness. If a second point of contact is needed, attach a prusik to the rope above the figure 8 descender.
Conduct visual and load tests in a safe location and advise your rescuer at the bottom that you are on belay and on rappel. The rescuer at the bottom can act as a bottom belay by pulling on the rope, which will increase friction in the figure 8 descender. If the rappelling rescuer should become incapacitated, the bottom belay can lower the rescuer by controlling the friction from below. Maintain a proper L-shaped stance when rappelling and moderate the amount of friction on the figure 8 descender by bringing your brake hand towards the figure 8 (decreases friction=faster descent) or bringing it away from the figure 8 towards your buttocks (increases friction=slower or stopped descent).
Properly laced figure 8 with brake hand in position. Never take your brake hand off the rope, unless the friction device is locked off.
Should the rappelling rescuer need to stop and perform a task, the figure 8 descender should be locked off. (If a prusik knot back up is used, it may be locked as well, but it may be difficult to unlock if loaded heavily.) To lock off a figure 8 descender bring the rope in your brake hand up and across the figure 8 between the standing part of the rope and the figure 8 descender in one continuous motion.
Bring the rope from your brake hand across the back of the figure 8 descender in one continuous motion. This locks off the figure 8 friction device.
To complete the locking off of the figure 8 descender, bring the rope across the back of the figure 8 like before as a second locking off and then insert a bight of rope through the figure 8 and tie an overhand safety knot around the standing end of the rope.
Lock off the figure 8 a second time and complete the lock off by bringing a bight of rope back through the figure 8 and tie an overhand safety knot around the standing end of the rope.
When the rescuer needs to continue rappelling, unlock the figure 8 descender by completing the above steps in reverse order. When unlocking the last wrap around the figure 8 descender complete it in one continuous motion. There will be a slight drop as the slack from the locked off figure 8 is taken up. If you have a prusik back-up above your figure 8 that has been loaded and needs to be un-weighted, lock off your figure 8 descender. Attach a long prusik loop to the rope between the locked (top) prusik and your figure 8. Use this long prusik loop as a foothold to stand up in to remove the weight from the locked (top) prusik. As you sit down to transfer your weight to the figure 8 descender, slide the top prusik downward to avoid locking it again. Remove the foot loop prusik and unlock your figure 8 to continue your descent. This procedure can also be used to change over from ascending to descending by a figure 8.