Академический Документы
Профессиональный Документы
Культура Документы
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9815 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
415 1226 00
PAGE 1
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2DQ
A00A22Q
1. 417 1184 00 2. 404 1304 00 404 1249 00 404 1248 00 404 1240 00 404 1241 00 3. 404 1169 00 4. 417 1144 00
Spring Main jet Main jet Main jet Main jet Main jet Needle jet Weight
PAGE 2
1998-SKANDIC 380
HIGH ALTITUDE KIT (P/N 861 7638 00) DRIVE PULLEY
Altitude Clutching Spring Block Weight Capsule Engagement RPM 100 Maximum RPM 100 Sea Level Green/Green on Violet 417 0095 00 417 1181 00 Qty 3 x 1 417 1204 00 Qty 3 x 1 417 1145 00 2500 6900 600 m 2000 ft 1200 m 4000 ft Red/Blue on Violet 417 1184 00 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
3100
1200 m 4000 ft
Qty 3 x 4
1800 m 6000 ft
Qty 3 x 3
2000 m 8000 ft
Qty 3 x 2
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-SKANDIC 380
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 140 6DP9 3 2.5 40 1.25 1.5 P-0 (159) 23.9 1650 1.3 600 m 2000 ft 135 1200 m 4000 ft 130 1800 m 6000 ft 125 2400 m 8000 ft 115 3000 m 10000 ft 110 Qty 2 2 2 2 PTO MAG 2 2
.5 1.0
O-8 (159)
1.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9816 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
415 1227 00
PAGE 1
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2DQ
A00A22Q
1. 417 1184 00 2. 404 1304 00 404 1249 00 404 1248 00 404 1240 00 404 1241 00 3. 404 1169 00 4. 417 1144 00
Spring Main jet Main jet Main jet Main jet Main jet Needle jet Weight
PAGE 2
1998-TOURING E
HIGH ALTITUDE KIT (P/N 861 7636 00) DRIVE PULLEY
Altitude Clutching Spring Block Weight Capsule Engagement RPM 100 Maximum RPM 100 Sea Level Green/Green on Violet 417 0095 00 417 1181 00 Qty 3 x 1 417 1204 00 Qty 3 x 1 417 1145 00 2500 6900 600 m 2000 ft 1200 m 4000 ft Red/Blue on Violet 417 1184 00 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
3100
1200 m 4000 ft
Qty 3 x 4
1800 m 6000 ft
Qty 3 x 3
2000 m 8000 ft
Qty 3 x 2
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-TOURING E
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 140 6DP9 3 2.5 40 1.25 1.25 1.5 P-0 (159) 23.9 1650 1.3 600 m 2000 ft 135 1200 m 4000 ft 130 1800 m 6000 ft 125 2400 m 8000 ft 115 3000 m 10000 ft 110 Qty 2 2 2 2 PTO MAG 2 2
0.5 1.0
O-8 (159)
1.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9817 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
415 1225 00
PAGE 1
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01C2CQ
A01C2EQ
A00A22Q
A05D0HQ
1. 417 1156 00 2. 404 1195 00 404 1192 00 404 1266 00 404 1249 00 404 1248 00 3. 404 1027 00 4. 417 1158 00 5. 417 1157 00
Spring Blue Main jet 185 Main jet 175 Main jet 140 Main jet 130 Main jet 125 Pilot jet 35 Weight Centrifugal block
PAGE 2
1998-TUNDRA II LT
HIGH ALTITUDE KIT (P/N 861 7639 00) DRIVE PULLEY
Altitude Clutching Spring Block Weight Capsule Engagement RPM 100 Maximum RPM 100 Sea Level Turquoise 417 1159 00 Qty 3 x 1 417 1143 00 --417 1145 00 3100 6900 600 m 2000 ft 1200 m 4000 ft Blue 417 1156 00 Qty 3 x 1 417 1157 00 Qty 3 x 3 417 1158 00 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
Qty 3 x 2
1800 m 6000 ft
Qty 3 x 2
2000 m 8000 ft
Qty 3 x 1
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level White 414 5099 00 3.6 7.9 1200 m 4000 ft
5.9 13.0
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-TUNDRA II LT
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 190 6DH4 2 2.5 40 1.0 1.5 0-8 (159) 23.9 1200 1.3 600 m 2000 ft 185 1200 m 4000 ft 175 1800 m 6000 ft 140 2400 m 8000 ft 130 3000 m 10000 ft 125 Qty 1 1 1 1 1 1
35
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of -20C (-4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9818 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2EQ
A01D18Q
1. 414 7421 00 2. 404 1182 00 404 1209 00 404 1266 00 404 1249 00 404 1239 00 3. 404 1094 00 4. 417 0052 92
Spring Main jet Main jet Main jet Main jet Main jet Pilot jet Ramp
PAGE 2
1998-SKANDIC 500
HIGH ALTITUDE KIT (P/N 861 7637 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Red/Yellow 414 8175 00 Qty 3 x 1 417 0052 91 3 Qty 3 x 1 417 0043 09 2900 7000 600 m 2000 ft 1200 m 4000 ft Yellow/Green 414 7421 00 Qty 3 x 1 417 0052 92 2 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
3300
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6
5.5 12.1
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-SKANDIC 500
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 180 170 6DH2 3 2.5 40 1.88 1.5 P-0 (159) 23.9 1650 1.5 600 m 2000 ft 170 160 1200 m 4000 ft 160 150 1800 m 6000 ft 150 140 2400 m 3000 m 8000 ft 10000 ft 140 130 Qty PTO MAG 2 2 2 2 2
45 1.5
130 120
1.6
1.7
1.8
1.85
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of -20C (-4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9819 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01C2DQ
A00A22Q
1. 404 1304 00 404 1249 00 404 1248 00 404 1240 00 404 1241 00 2. 404 1169 00 3. 417 1144 00
Main jet Main jet Main jet Main jet Main jet Needle jet Weight
PAGE 2
600 m 2000 ft
Qty 3 x 5 417 1144 00
Qty 3 x 4
1800 m 6000 ft
Qty 3 x 3
2000 m 8000 ft
Qty 3 x 2
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6 1200 m 4000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 140 6DP9 3 2.5 40 1.25 1.25 1.5 P-0 (159) 23.9 1650 1.3 600 m 2000 ft 135 1200 m 4000 ft 130 1800 m 6000 ft 125 2400 m 8000 ft 115 3000 m 10000 ft 110 Qty 2 2 2 2 PTO MAG 2 2
.5 1.0
O-8 (159)
1.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9825 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01C2CQ
A01D18Q
1. 414 7421 00 2. 404 1122 00 404 1238 00 404 1182 00 404 1209 00 404 1266 00 3. 417 0052 92
Spring Main jet Main jet Main jet Main jet Main jet Ramp
PAGE 2
1998-TOURING LE
HIGH ALTITUDE KIT (P/N 861 7635 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Red/Blue 414 6915 00 Qty 3 x 1 417 0052 91 2 417 0043 09 2900 7000 600 m 2000 ft 1200 m 4000 ft Yellow/Green 414 7421 00 Qty 3 x 1 417 0052 92 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft 3
1800 m 6000 ft 4
2000 m 8000 ft 5
3000 m 10000 ft 6
3000
1200 m 4000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-TOURING LE
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 200 190 6DH2 3 2.5 35 1.50 1.5 P-0(159) 23.9 1650 1,5 600 m 2000 ft 190 180 1200 m 4000 ft 180 170 1800 m 6000 ft 170 160 2400 m 8000 ft 160 150 3000 m 10000 ft 150 140 Qty PTO MAG 2 2 2 2 2
1.00
1,9
1,6
1,7
1,8
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9834 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A00A3JQ
A01C2DQ
1. 414 7421 00 2. 404 1011 00 404 1005 00 404 1006 00 404 1003 00 404 1002 00 404 1189 00 404 1191 00 404 1123 00 404 1190 00 404 1122 00 3. 417 0043 09 4. 404 1332 00 404 1618 01
Spring Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Pin Needle jet Needle jet
Yellow/Green 290 280 260 250 240 230 210 200 190 180 P-0 (480) O-9 (480)
(1) (2) (1) (2) (1) (2) (1) (2) (1) (2) (1) (3) (3) (3)
PAGE 2
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
CAUTION
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve cover approximately 3 turns.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9840 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01C2CQ
A01C2EQ
A01D18Q
A00A3JQ
1. 404 1005 00 404 1003 00 404 1189 00 404 1123 00 404 1122 00 2. 404 1210 00 3. 417 0052 85 4. 417 0043 09
Main jet Main jet Main jet Main jet Main jet Pilot jet Ramp Pin
PAGE 2
1998-MACH 1
HIGH ALTITUDE KIT (P/N 861 7610 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Green/Violet 414 7628 00 Qty 3 x 1 417 0052 86 2 Qty 3 x 1 417 0043 08 4200 8300 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve covers approximately three (3) turns.
PAGE 3
1998-MACH 1
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 300 6DEY2 4 2.5 50 2.00 1.5 P-9 (480) 18.1 1800 1.20 600 m 2000 ft 280 1200 m 4000 ft 250 1800 m 6000 ft 230 2400 m 8000 ft 200 3000 m 10000 ft Qty 3 3 3 3 3 3
1200 m 4000 ft 270 260 250 240 240 230 220
60 1.50
180
1.00
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9841 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01C2CQ
A01C2DQ
A00A3JQ
A01D1OQ
1. 404 1011 00 404 1005 00 404 1006 00 404 1003 00 404 1002 00 404 1189 00 404 1191 00 404 1123 00 404 1190 00 404 1122 00 2. 404 1332 00 404 1618 01 3. 417 0043 09 4. 415 0349 00
Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Needle jet Needle jet Pin Spring
290 280 260 250 240 230 210 200 190 180 P-0 (480) O-9 (480) Violet/Blue
(2) (1) (2) (1) (2) (1) (2) (1) (2) (1) (3) (3) (3) (1)
PAGE 2
600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 310 300 310 6DEH5 3 2.5 50 2.50 1.5 P-1 (480) 18.1 1800 1.20 600 m 2000 ft 290 280 290 1200 m 4000 ft 260 250 260 1800 m 6000 ft 240 230 240 2400 m 8000 ft 210 200 210 3000 m 10000 ft 190 180 190 Qty PTO CTR MAG 3 3 3 3 3
1.25
1.75
1.50
1.00
P-0 (480)
O-9 (480)
1.40
1.60
1.80
2.00
2.20
330/ 300/ 280/ 250/ 230/ 320/330 290/300 270/280 240/250 220/230 320/ 290/ 270/ 240/ 220/ 310/320 280/290 260/270 230/240 210/220
310/ 290/ 260/ 240/ 210/ 190/ PTO/ 300/310 280/290 250/260 230/240 200/210 180/190 CTR/MAG 300/ 280/ 250/ 230/ 200/ 290/300 270/280 240/250 220/230 195/200 290/ 270/ 240/ 220/ 195/ 280/290 260/270 230/240 210/220 190/195 270/ 250/ 230/ 210/ 185/ 260/270 240/250 220/230 200/210 175/185 260/ 240/ 220/ 200/ 180/ 250/260 230/240 210/220 190/200 170/180 180/ PTO/ 175/180 CTR/MAG 175/ PTO/ 170/175 CTR/MAG 160/ PTO/ 155/160 CTR/MAG 155/ PTO/ 150/155 CTR/MAG
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9842 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01D18Q
A00A3JQ
Violet/Violet 285
PAGE 2
1998-GRAND TOURING SE
HIGH ALTITUDE KIT (P/N 861 7630 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Blue/Pink 414 9163 00 Qty 3 x 1 417 0052 86 2 Qty 3 x 1 417 0043 08 3600 8500 600 m 2000 ft 1200 m 4000 ft Violet/Violet 414 8179 00 Qty 3 x 1 417 0052 85 2 Qty 3 x 1 417 0043 09 4300 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-GRAND TOURING SE
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 300 6DEY2 4 2.5 50 2.00 1.5 P-9 (480) 18.1 1800 1.20 600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2400 m 8000 ft
3000 m 10000 ft
Qty 3 3 3 3 3 3 3
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve cover approximately three (3) turns.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9843 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01C2CQ
A01C2EQ
A00A3JQ
A01D18Q
1. 404 1004 00 404 1002 00 404 1112 00 404 1123 00 404 1238 00 2. 404 1210 00 3. 417 0043 09 4. 417 0052 81
Main jet Main jet Main jet Main jet Main jet Pilot jet Pin Ramp
PAGE 2
600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 290 6DEY4 3 2.5 50 2.00 1.5 P-0 (286) 18.1 1800 1.20 600 m 2000 ft 270 1200 m 4000 ft 240 1800 m 6000 ft 220 2400 m 8000 ft 200 3000 m 10000 ft 170 Qty 3 3 3 3 3
1200 m 4000 ft 270 250 240 240 230 220 210
60 1.50
1.00
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9844 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01C2CQ
A01C2EQ
A00A3JQ
A01D1OQ
1. 404 1078 00 404 1012 00 404 1011 00 404 1005 00 404 1003 00 404 1112 00 404 1123 00 2. 404 1453 00 3. 417 0043 09 4. 414 7682 00
Main jet Main jet Main jet Main jet Main jet Main jet Main jet Pilot jet Pin Spring
(1) (2) (1) (2) (3) (3) (3) (3) (3) Green/Blue (1)
PAGE 2
1998-MACH Z/MACH Z LT
HIGH ALTITUDE KIT (P/N 861 7609 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Violet/Green 415 0154 00 Qty 3 x 1 417 0052 86 2 Qty 3 x 1 417 0043 08 3900 8300 600 m 2000 ft 3 1200 m 4000 ft Green/Blue 414 7682 00 2 Qty 3 x 1 417 0043 09 4200 1800 m 6000 ft 3 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-MACH Z/MACH Z LT
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 330 340 330 8ABY1-40 3 2.0 50 4.00 1.5 O-3 (327) 20.0 1800 1.20 600 m 2000 ft 300 310 300 1200 m 4000 ft 280 290 280 2 3.50 1800 m 6000 ft 250 250 250 60 2400 m 8000 ft 220 220 220 3.00 3000 m 10000 ft 200 200 200 1 2.00 Qty PTO CTR MAG 3 3 3 3 3
350/ 320/ 300/ 270/ 240/ 210/ PTO/ 360/350 330/320 310/300 270/270 240/240 210/210 CTR/MAG 340/ 310/ 290/ 260/ 230/ 205/ PTO/ 350/340 320/310 300/290 260/260 230/230 205/205 CTR/MAG 330/ 300/ 280/ 250/ 220/ 200/ PTO/ 340/330 310/300 290/280 250/250 220/220 200/200 CTR/MAG 320/ 290/ 270/ 240/ 220/ 190/ PTO/ 330/320 300/290 280/270 240/240 220/220 190/190 CTR/MAG 310/ 290/ 260/ 240/ 210/ 190/ PTO/ 320/310 300/290 270/260 240/240 210/210 190/190 CTR/MAG 300/ 280/ 250/ 230/ 210/ 180/ PTO/ 310/300 290/280 260/250 230/230 210/210 180/180 CTR/MAG 290/ 270/ 240/ 220/ 200/ 170/ PTO/ 300/290 280/270 250/240 220/220 200/200 170/170 CTR/MAG
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9845 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
1. 414 6915 00 2. 404 1112 00 404 1123 00 404 1122 00 404 1238 00 404 1182 00
Spring Main jet Main jet Main jet Main jet Main jet
PAGE 2
1998-SKANDIC SWT
HIGH ALTITUDE KIT (P/N 861 7643 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Red/Yellow 414 8175 00 Qty 3 x 1 417 0051 46 4 Qty 3 x 1 417 0043 09 2300 6500 600 m 2000 ft 5 1200 m 4000 ft Red/Blue 414 6915 00 2 1800 m 6000 ft 3 2800 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle (degrees) Sea Level Blue A C S 3 - 188 6.0 13.2 40 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-SKANDIC SWT
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 230 6DH8 4 3.0 25 1.5 1.5 O-0 (159) 23.9 1650 1.5 600 m 2000 ft 220 1200 m 4000 ft 200 1.6 1800 m 6000 ft 180 3 0.75 1.7 2400 m 8000 ft 170 1.8 3000 m 10000 ft 160 1.9 Qty 1 1 1 1 2 1
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9846 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
1. 414 8177 00 2. 404 1123 00 404 1190 00 404 1122 00 404 1238 00 404 1182 00
Spring Main jet Main jet Main jet Main jet Main jet
PAGE 2
1998-SKANDIC WT
HIGH ALTITUDE KIT (P/N 861 7642 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Yellow/Orange 414 6897 00 Qty 3 x 1 417 0052 90 4 Qty 3 x 1 417 0043 09 2800 6800 600 m 2000 ft 5 1200 m 4000 ft 6 1800 m 6000 ft Blue/Green 414 8177 00 2 3100 2400 m 8000 ft 3 3000 m 10000 ft 4
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle (degrees) Sea Level Blue A C S 3 - 188 7.0 15.4 40 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-SKANDIC WT
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 210 6DH2 3 2.5 40 1.5 1.5 P-4 (159) 23.9 1650 1.5 600 m 2000 ft 200 1200 m 4000 ft 190 1.6 1800 m 6000 ft 180 2 0.75 1.7 2400 m 8000 ft 170 1.8 3000 m 10000 ft 160 1.9 Qty 2 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9847 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01C2CQ
A01C2CQ
1. 414 6898 00 2. 404 1189 00 404 1191 00 404 1123 00 404 1190 00 404 1122 00 404 1238 00 404 1182 00 404 1209 00 3. 417 0043 09
Spring Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Pin
(1) (1) (1) (1) (1) (1) (1) (1) (1) (3)
PAGE 2
1998-SKANDIC WT LC
HIGH ALTITUDE KIT (P/N 861 7641 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Yellow/Blue 414 8180 00 Qty 3 x 1 417 0052 90 4 Qty 3 x 1 417 0043 08 2500 7000 600 m 2000 ft 5 1200 m 4000 ft Red/Red 414 6898 00 3 Qty 3 x 1 417 0043 09 1800 m 6000 ft 4 2400 m 8000 ft 5 3000 m 10000 ft 6
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle (degrees) Sea Level Blue A C S 3 - 188 7.0 15.4 40 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-SKANDIC WT LC
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 250 220 6DH4 2 2.5 30 1.0 1.5 P-2 (159) 23.9 1800 1.5 600 m 2000 ft 230 200 1.6 1200 m 4000 ft 210 180 1.7 1800 m 6000 ft 200 170 1 1.8 2400 m 8000 ft 190 160 1.9 3000 m 10000 ft 180 150 2.0 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9859 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01C2CQ
A01C2EQ
A00A22Q
A05D0HQ
1. 417 1185 00 2. 404 1195 00 404 1192 00 404 1266 00 404 1249 00 404 1248 00 3. 404 1027 00 4. 417 1158 00 5. 417 1157 00
Spring Yellow/Green (1) Main jet 185 (1) Main jet 175 (1) Main jet 140 (1) Main jet 130 (1) Main jet 125 (1) Pilot jet 35 (1) Weight (9) Centrifugal block (3)
PAGE 2
1998-TUNDRA R
HIGH ALTITUDE KIT (P/N 861 7640 00) DRIVE PULLEY
Altitude Clutching Spring Block Weight Capsule Engagement RPM 100 Maximum RPM 100 Sea Level Turquoise 417 1159 00 Qty 3 x 1 417 1143 00 Qty 2 x 3 417 1145 00 3100 6900 600 m 2000 ft 1200 m 4000 ft Yellow/Green 417 1185 00 Qty 3 x 1 417 1157 00 Qty 3 x 3 417 1158 00 1800 m 6000 ft Qty 3 x 2 2400 m 8000 ft Qty 3 x 2 3000 m 10000 ft Qty 3 x 1
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle (degrees) Sea Level Yellow 415 0943 00 0.00 Position1 0.00 37.8 417 1241 00 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-TUNDRA R
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 190 6DH4 2 2.5 40 1.0 1.5 O-8 (159) 23.9 1200 1.3 600 m 2000 ft 185 1200 m 4000 ft 175 1800 m 6000 ft 140 35 2400 m 8000 ft 130 3000 m 10000 ft 125 Qty 1 1 1 1 1 1
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9860 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
1. 414 7421 00 2. 404 1182 00 404 1209 00 404 1266 00 404 1249 00 404 1239 00 3. 404 1094 00 4. 417 0052 92 5. 515 1747 00
Spring Main jet Main jet Main jet Main jet Main jet Pilot jet Ramp Reverse connector
PAGE 2
1998-TOURING SLE
HIGH ALTITUDE KIT (P/N 861 7634 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Red/Yellow 414 8175 00 Qty 3 x 1 417 0052 91 3 Qty 3 x 1 417 0043 09 2900 7000 600 m 2000 ft 4 1200 m 4000 ft Yellow/Green 414 7421 00 Qty 3 x 1 417 0052 92 2 3300 1800 m 6000 ft 3 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Yellow 415 0928 00 0.00 Position 1 0.00 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
ELECTRONIC REVERSE
Sea Level Reverse Connector 515 1748 00 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2400 m 8000 ft 515 1747 00 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-TOURING SLE
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 180 170 6DH2 3 2.5 40 1.88 1.5 P-0 (159) 23.9 1650 1.5 600 m 2000 ft 170 160 1.8 1200 m 4000 ft 160 150 2.1 1800 m 6000 ft 150 140 45 0.750 1550 2.4 2400 m 3000 m 8000 ft 10000 ft 140 130 2.5 130 120 2.6 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9862 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2EQ
A01D18Q
1. 414 6895 00 2. 404 1238 00 404 1182 00 404 1209 00 404 1266 00 404 1249 00 404 1239 00 3. 404 1094 00 4. 417 0052 92
Spring Main jet Main jet Main jet Main jet Main jet Main jet Pilot jet Ramp
PAGE 2
1998-FORMULA SL
HIGH ALTITUDE KIT (P/N 861 7619 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Yellow/Red 414 9930 00 Qty 3 417 0052 91 3 Qty 3 417 0043 09 3300 7000 600 m 2000 ft 4 1200 m 4000 ft Blue/Yellow 414 6895 00 Qty 3 417 0052 92 2 3600 1800 m 6000 ft 3 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 414 5058 00 4.8 10.6 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-FORMULA SL
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURETION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 180 170 6DH2 3 2.5 40 1.875 1.5 P-0 (159) 23.9 1650 1.5 600 m 2000 ft 170 160 1200 m 4000 ft 160 150 1.6 1800 m 6000 ft 150 140 2 45 1.5 1.7 2400 m 3000 m 8000 ft 10000 ft 140 130 1.8 130 120 1.85 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9863 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01C2DQ
A00A3JQ
1. 404 1011 00 404 1004 00 404 1006 00 404 1002 00 404 1112 00 404 1191 00 404 1123 00 404 1190 00 404 1192 00 2. 404 1335 00 404 1554 00 3. 417 0043 09
Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Needle jet Needle jet Pin
290 270 260 240 220 210 200 190 175 AA-0 (224) AA-1 (224)
(1) (1) (1) (1) (1) (1) (1) (1) (1) (2) (2) (3)
PAGE 2
1998-FORMULA Z 670
HIGH ALTITUDE KIT (P/N 861 7614 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Violet/Yellow 415 0153 00 417 0052 86 3 Qty 3 x 1 417 0043 08 3800 7700 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2400 m 8000 ft 3000 m 10000 ft
4 Qty 3 x 1 417 0043 09 4500
600 m 2000 ft
1200 m 4000 ft
1800 m 6000 ft
2000 m 8000 ft
3000 m 10000 ft
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
1998-FORMULA Z 670
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 310 290 7EDY1 3 2.5 60 2.25 1.5 AA-3 (224) 18.1 1700 2.10 600 m 2000 ft 290 270 1200 m 4000 ft 260 240 1800 m 6000 ft 240 220 2400 m 8000 ft 210 200 3000 m 10000 ft 190 175 Qty PTO MAG 2 2 2 2 2
1.75
2.00
1.50
AA-1 (224)
2.15
2.25
2.40
2.55
2.65
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of -20C (-4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9864 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01C2DQ
A01D18Q
1. 404 1002 00 404 1189 00 404 1191 00 404 1190 00 404 1238 00 404 1209 00 2. 404 1335 00 3. 417 0052 89
Main jet Main jet Main jet Main jet Main jet Main jet Needle jet Ramp
PAGE 2
1998-FORMULA Z 583
HIGH ALTITUDE KIT (P/N 861 7615 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Violet/Blue 415 0349 00 Qty 3 x 1 417 0052 86 3 417 0043 09 4100 7900 600 m 2000 ft 4 1200 m 4000 ft 5 1800 m 6000 ft Qty 3 x 1 417 0052 89 3 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
1998-FORMULA Z 583
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 280 260 7ECY1 3 2.5 60 2.0 1.5 AA-2 (224) 18.1 1800 2.0 600 m 2000 ft 260 240 2.10 1200 m 4000 ft 230 210 2.20 1800 m 6000 ft 210 190 2 AA-0 (224) 2.60 2400 m 8000 ft 190 170 1.75 2.70 3000 m 10000 ft 170 150 1.5 2.80 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9865 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01C2DQ
A01D18Q
1. 404 1003 00 404 1002 00 404 1189 00 404 1112 00 404 1191 00 404 1123 00 404 1194 00 404 1195 00 404 1122 00 404 1238 00 2. 404 1573 00 404 1315 00 3. 417 0052 89
Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Needle jet Needle jet Ramp
250 240 230 220 210 200 195 185 180 170 P-5 (480) P-4 (480) 289
(1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (2) (2) (3)
PAGE 2
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 270 260 6DEY4 2 2.5 50 2.00 1.5 P-7 (480) 18.1 1800 2.00 600 m 2000 ft 250 240 1.75 2.10 1200 m 4000 ft 230 220 1.50 2.20 1800 m 6000 ft 210 200 1 P-5 (480) 2.30 2400 m 8000 ft 195 185 2.40 3000 m 10000 ft 180 170 P-4 (480) 2.50 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of -20C (-4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9866 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01C2CQ
A01C2EQ
A01D18Q
A00C4YQ
1. 404 1006 00 404 1002 00 404 1112 00 404 1191 00 404 1123 00 404 1122 00 2. 404 1139 00 3. 417 0052 81 4. 420 2399 46
Main jet Main jet Main jet Main jet Main jet Main jet Pilot jet Ramp Rave Valve spring
PAGE 2
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: At 1800 m/6000 ft, change 2 Rave Valve springs, using P/N 420 2399 46.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 300 280 6DGY9 2 2.5 50 2.00 1.5 Q-3 (480) 18.1 1800 1.80 600 m 2000 ft 280 260 1.90 1200 m 4000 ft 260 240 2.00 1800 m 6000 ft 240 210 1 55 2.10 2400 m 8000 ft 220 200 2.20 3000 m 10000 ft 200 180 2.30 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9867 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A00A3JQ
A01C2DQ
1. 404 1011 00 404 1004 00 404 1006 00 404 1002 00 404 1112 00 404 1191 00 404 1123 00 404 1190 00 404 1192 00 2. 417 0043 09 3. 404 1554 00 404 1335 00
Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Pin Needle Jet Needle Jet
290 270 260 240 220 210 200 190 175 AA-1 (224) AA-0 (224)
(1) (1) (1) (1) (1) (1) (1) (1) (1) (3) (2) (2)
PAGE 2
1998-MX Z 670
HIGH ALTITUDE KIT (P/N 861 7621 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Violet/Yellow 415 0153 00 Qty 3 x 1 417 0052 86 3 Qty 3 x 1 417 0043 08 3800 7700 600 m 2000 ft 4 1200 m 4000 ft 5 1800 m 6000 ft 4 Qty 3 x 1 417 0043 09 4500 2400 m 8000 ft 5 3000 m 10000 ft 6
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
1998-MX Z 670
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Float level Needle jet Idle Idle throttle valve position RPM 200 mm mm Sea Level 310 290 7EDY1 3 2.5 60 2.25 1.5 18.1 AA-3 (224) 1700 2.10 600 m 2000 ft 290 270 2.15 1200 m 4000 ft 260 240 2.0 2.25 1800 m 6000 ft 240 220 2 1.75 AA-1 (224) 2.40 2400 m 8000 ft 210 200 1.5 2.55 3000 m 10000 ft 190 175 1.25 AA-0 (224) 2.65 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9868 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01C2DQ
A01D18Q
1. 404 1006 00 404 1002 00 404 1189 00 404 1191 00 404 1190 00 404 1238 00 404 1209 00 2. 404 1335 00 3. 417 0052 89
Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Needle jet Ramp
260 240 230 210 190 170 150 AA-0 (224) 289
PAGE 2
1998-MX Z 583
HIGH ALTITUDE KIT (P/N 861 7622 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Green/Blue 414 7682 00 Qty 3 x 1 417 0052 86 3 Qty 3 x 1 417 0043 09 4400 7900 600 m 2000 ft 4 1200 m 4000 ft 5 1800 m 6000 ft Qty 3 x 1 417 0052 89 2 4500 2400 m 8000 ft 3 3000 m 10000 ft 4
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
1998-MX Z 583
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 280 260 7ECY1 3 2.5 60 2.0 1.5 AA-2 (224) 18.1 1800 2.0 600 m 2000 ft 260 240 2.10 1200 m 4000 ft 230 210 2.20 1800 m 6000 ft 210 190 2 AA-0 (224) 2.60 2400 m 8000 ft 190 170 1.75 2.70 3000 m 10000 ft 170 150 1.5 2.80 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9869 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01C2CQ
A01D1OQ
A00C4YQ
1. 404 1006 00 404 1002 00 404 1112 00 404 1191 00 404 1123 00 404 1122 00 2. 414 7682 00 3. 420 2399 46
Main jet Main jet Main jet Main jet Main jet Main jet Spring Rave Valve spring
PAGE 2
1998-MX-Z 500
HIGH ALTITUDE KIT (P/N 861 7623 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Violet/Yellow 415 0153 00 417 0052 81 2 417 0043 09 4100 7800 600 m 2000 ft 3 1200 m 4000 ft 4 1800 m 6000 ft Green/Blue 414 7682 00 4 4300 2400 m 8000 ft 5 3000 m 10000 ft 6
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 415 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: At 1800 m/6000 ft, change 2 Rave Valve springs, using P/N 420 2399 46.
PAGE 3
1998-MX-Z 500
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 300 280 6DGY9 3 2.5 50 2.5 1.5 Q-4 (480) 18.1 1800 1.8 600 m 2000 ft 280 260 1.9 1200 m 4000 ft 260 240 2.0 1800 m 6000 ft 240 210 2 2.0 2.1 2400 m 8000 ft 220 200 2.2 3000 m 10000 ft 200 180 2.3 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9870 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2DQ
A01D18Q
1. 415 0349 00 2. 404 1003 00 404 1002 00 404 1189 00 404 1112 00 404 1191 00 404 1123 00 404 1194 00 404 1195 00 404 1122 00 404 1238 00 3. 404 1573 00 404 1315 00 4. 417 0052 89
Spring Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Main jet Needle jet Needle jet Ramp
Violet/Blue 250 240 230 220 210 200 195 185 180 170 P-5 (480) P-4 (480) 289
(1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (2) (2) (3)
PAGE 2
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: Unscrew Rave Valve adjuster screws approximately three (3) turns at 2400 m/8000 ft.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 270 260 6DEY4 2 2.5 50 2.0 1.5 P-7 (480) 18.1 1800 2.00 600 m 2000 ft 250 240 1.75 2.10 1200 m 4000 ft 230 220 1.5 2.20 1800 m 6000 ft 210 200 1 P-5 (480) 2.30 2400 m 8000 ft 195 185 2.40 3000 m 10000 ft 180 170 P-4 (480) 2.50 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9871 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2
A01D1OQ
A01C2CQ
A01C2DQ
A00C4YQ
1. 414 6894 00 2. 404 1006 00 404 1002 00 404 1112 00 404 1191 00 404 1123 00 404 1122 00 3. 404 1139 00 4. 420 2399 46
Spring Main Jet Main Jet Main Jet Main Jet Main Jet Main Jet Needle Jet Rave Valve spring
PAGE 2
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Beige 414 5589 00 7.0 15.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated. Additional Information: At 1800 m/6000 ft, change 2 Rave Valve springs, using P/N 420 2399 46.
PAGE 3
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 300 280 6DGY9 2 2.5 50 2.0 1.5 Q-3 (480) 18.1 1800 1.80 600 m 2000 ft 280 260 1200 m 4000 ft 260 240 1800 m 6000 ft 240 210 1 55 2.25 2400 m 8000 ft 220 200 3000 m 10000 ft 200 180 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4
BOMBARDIER snowmobiles
WARNING
For safety reasons, this kit must be installed by an authorized Bombardier snowmobile dealer. Should removal of a locking device be required when undergoing disassembly/assembly, always replace with a new one. This instruction sheet should be given to the purchaser. This kit is designed for specific models. It is not recommended for vehicles other than those for which it was sold.
CAUTION
The following modifications and adjustments apply only for altitudes above 600 m (2 000 ft). NOTE: Installation time is approximately 1.5 hours.
CARBURETOR JETTING
Stock vehicle jetting and the main jets included in this kit are prescribed for a temperature of 20C (4F), as indicated by bold face type on the main jet chart. Snowmobile utilization above or below this temperature requires a different jetting. In that case, find the required main jet size in Carburation chart and order it according to the Bombardier P/N (part numbers) given in Main Jet P/N chart that can be found in the previously mentioned High Altitude Technical Data sheets.
Lithod in Canada (MSI-9875 MD) *Trademarks of Bombardier Inc. 1997 Bombardier Inc. All rights reserved.
PARTS TO BE INSTALLED
1 2 3
A01D1OQ
A01C2CQ
A01D18Q
1. 414 8177 00 2. 404 1190 00 404 1122 00 404 1238 00 404 1182 00 404 1209 00 404 1266 00 3. 417 0052 92
Spring Main jet Main jet Main jet Main jet Main jet Main jet Ramp
PAGE 2
1998-MX Z 440
HIGH ALTITUDE KIT (P/N 861 7625 00) DRIVE PULLEY
Altitude Clutching Spring Ramp Calibration screw position Pin Engagement RPM 100 Maximum RPM 100 Sea Level Blue/Yellow 414 6895 00 Qty 3 x 1 417 0052 91 3 Qty 3 x 1 417 0043 09 3700 7000 600 m 2000 ft 4 1200 m 4000 ft Blue/Green 414 8177 00 Qty 3 x 1 417 0052 92 2 1800 m 6000 ft 3 2400 m 8000 ft 4 3000 m 10000 ft 5
DRIVEN PULLEY
Altitude Clutching Spring Spring Kg 0.7 tension lb 1.5 Cam angle Sea Level Orange 415 5058 00 6.1 13.4 600 m 2000 ft 1200 m 4000 ft 1800 m 6000 ft 2000 m 8000 ft 3000 m 10000 ft
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 3
1998-MX Z 440
CAUTION
These adjustments are guidelines only. Specific adjustments vary with temperature, altitude and snow conditions. Always observe spark plug condition for proper jetting. CARBURATION
Altitude Calibration Main jet Jet needle Needle position Slide cut-away Pilot jet Air screw Valve seat Needle jet Float level Idle Idle throttle valve position mm RPM 200 mm Sea Level 205 195 6DH2 3 2.5 35 1.5 1.5 P-0 (159) 23.9 1650 1.5 600 m 2000 ft 190 180 1200 m 4000 ft 180 170 1.6 1800 m 6000 ft 170 160 2 1.0 1.7 2400 m 8000 ft 160 150 1.8 3000 m 10000 ft 150 140 1.9 Qty PTO MAG 2 2 2 2 2
NOTE: Arrows in the charts indicate that the preceding information is repeated.
PAGE 4