Вы находитесь на странице: 1из 18

GENERAL RATES FOR CIVIL MAINTENANCE WORK

Page 1

Sr.No

Description of Item

Unit

Rate

Remark

SECTION - A : EARTHWORK
Note:-The rates quoted by the Contractor for items under this head shall be inclusive of the following: (a) Cleaning the site as per instructions of clerk of work/Engineer-in-Charge / Consultants. (b) Setting out works as required and setting up Bench mark and other reference marks. ( c ) Providing, strutting and shoring and removing the same. Bailing or pumping out water as and when necessary. (d) Sorting out useful excavated materials for back filling and stacking them neatly on site as directed. (e) Preparation of bed for receiving concrete. (f) Back filling the trenches along the sides of masonry or concrete foundations upto natural ground level including watering and ramming. Filing the surplus material in building plinths, roads, parking or any other area within the site as directed including (g) Necessary explosives and equipments for blasting rock where necessary (including obtaining permissions from authorities), or chiselling the rock and stacking the same as directed. (h)Necessary protection including labour, materials and equipment to ensure safety and protecting against risk and accident. ( i )For measurements of rock excavation, stacks of excavated rock shall be made and measured. 30% voids shall be deducted from the stack measurement. ( j )If it is not possible to make stacks of rock excavated, then it shall be paid on volumetric basis as per actual levels of excavation. ( k )All filling will be compacted to achieve 90% density of the maximum density at optimum moisture content as tested using modified Procter Density test.

Page

Sr.No
1

Description of Item
Earth work in excavation below ground level/excavated level (level after mass excavation as per item 1 above) for all kinds of works in foundations, septic tanks including trenches, wall foundations etc. in all types of soils except soft/hard rock for including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading ramming of bottom of trenches, dewatering of accumulated water from any source, by pumping or manually and keeping surface dry for subsequent work and back-filling around foundations after completion of work including compacting in layers not exceeding 200 mm, dressing trimming etc. Complete,transporting and back-filling excess excavated material in low lying areas within the site anywhere including building plinths, roads etc. and compacting the same in layers of 300 mm, watering using water sprinklers dressing, trimming to specified profile

Unit

Rate

Remark

2 3 4

6 7

8 9

( A ) Depth upto 1.50 from GL Same as item No. 1 but for Excavation in Soft rock ( A ) Depth upto 1.50 from GL Same as item No. 2 but for Excavation in Hard rock Depth upto 1.50 from GL Supplying & filling in plinth or general site with good quality murrum obtained from outside the owner's premises including transporting to site, filling, grading, levelling,watering, ramming each layer of 300 mm max. depth with 10/12 ton power roller, vibratory compactor at inaccessible places. (Consolidated volume payable) Supplying and providing 230 mm thick dry rubble soling using stone rubble below foundations, roads and in plinth including hand setting vertically in regular lines, filing crevices using small stone chips, blinding layer of grit, watering, compacting using preparing subgrade by compacting using 10/12 T roller, filing crevices with small size stones, chips, sand filing in voids, spreading 12 mm grit on top surface, levelling, giving proper slopes etc. complete. ( A )- do - as Item above but for total thickness of 100 mm laid in single layer Providing and filling clean river sand including watering, ramming etc. in cable trenches, around foundations etc. as directed. Providing and fixing heavy duty plain grey interlocking pavers made in M30 grade concret, minimum 65 mm thick in 50 mm thick layer of sand bedding, vibrating and compacting etc. all complete -do- as 5a above but for grey cobblestone pavers 5"x5" Labour charges for removing existing paver blocks including stacking for reuse as directed, removing sand bedding, disposing off debris etc. all complete. Rebate over item 5a & 5b for using paver blocks available from site.

Cum Cum

Cum

Cum

Sqm

Page

Sr.No

Description of Item
SECTION - B : CONCRETE AND ALLIED WORKS Note :-The rates quoted by the Contractor for items under this head shall be inclusive of the following: ( a )Works in this heading shall be executed in conformity with I.S. 456 (latest revision). (b)All materials, labour, tools and plant, scaffolding etc. mixing covering and placing concrete in position, ramming, vibrating, trowelling, curing with all lifts and leads. Removal of water from the pits as and when required from time to time. Mechanical Curing compound may be permitted only for inaccessible locations in consultation with the Structural Consultant. ( c )Form work paid under a separate item shall be inclusive of erecting, propping to required heights, bracing, providing stays, struts, bolts, nuts, use of adjustable steel props and everything necessary to keep the forms rigid, and shall include deshutterin ( d )Form work shall be designed to conform to dimensions and shapes as in the working drawings and take the laod of pumped concrete, including making chamfers and rebates or grooves. The surfaces to receive concrete shall be kept clean and smooth and coated with shuttering oil/mould releasing agent of approved quality before each use. Rate to include curing, hacking and preparing surface to receive plaster. The design/type of formwork shall be got approved by Consultants well in advance. ( e )The steel reinforcement shall be placed in position as per approved bar bending schedule with cutting to length, handling, hoisting including cost of binding wire required, precast concrete cover blocks, chairs, etc. to keep reinforcement in position at a The rate for pouring concrete shall cover for any shape of structural member like columns, beams, fascias, fins, pardis and walls, louvers, suspenders, etc. and for cantilever slabs, beams, machine foundations etc. ( f )Formation and treatment of contraction and expansion joints (water stops/shalitex) shall be paid separately. ( g )Design of mixes where so required by specifications shall be tested in approved laboratory and also tests of materials and work required in opinion of consultants. All the charges for testing shall be borne by contractor. Design mix shall be based on 50 K ( h )Fixing all inserts, forming of holes, requirement of different shapes of concrete openings in slabs, walls, holes of conduit pipes, etc. shall be covered in rates. ( i )Taking out dowel bars, fan hooks through form work. ( j )The spill-over of richer concrete at the junction of various concrete members shall be carried out as per the instructions.

Unit

Rate

Remark

( k )No extra shall be paid for rich concrete spill-over to the adjoining members. ( l )RCC suction tank and overhead tank shall be constructed as per rates of respective items involved in the work.

Page

Sr.No

Description of Item

Unit

Rate

Remark

Cement for all RCC works shall in general be Grade 43 except where specifically mentioned differently. Use of fly ash as per approved mix design shall be permitted. Fly ash to be provided by contractor at his own cost. Only river sand shall be used for concrete works. However, crushed stone grit, properly graded, may be considered in place of sand in RCC/PCC works subject to approval of mix design by Consultant including carrying out neccessary tests, cube tests etc., a The rate shall include cost of admixtures as required & hacking of surfaces where plaster is specified. Hacking should be done immediately after removal of formwork. Construction joints shall be minimum in numbers and their location shall be approved by the Structural Consultant. Such joints shall be properly treated with bonding coat of approved material applied at the old concrete before commencing fresh concrete. Honey combing, if any, shall be repaired only with polymer concrete or epoxy mortar with quartz sand as instructed by Structural Consultant. Members which in the opinion of the Structural Consultant are not acceptable, will have to be demolished and recas

Page

Sr.No

Description of Item

Unit

Rate

Remark

Providing and laying plain cement concrete (PCC) in substructure in foundations below footings, walls beams etc. and in superstructure of nominal mix of 1:3:6 (1 cement; 3 sand; 6 crushed stone aggregate) for pipe encasement, enclosing dowels, ramps etc. P & L 1:3:6 PCC as above in bedding in subfloor in thickness from 100 mm to 150 mm. Providing and mixing approved waterproofing compound Roffe or approved equivalent in concrete/plastering for works, where directed & not included in item description.

Cum

2 3

Cum Cum

Page

Sr.No

Description of Item

Unit

Rate

Remark

SECTION - C : MASONRY Note-:The rate quoted by the Contractor for items under this head shall be Inclusive of the following All labour, materials, use of tools, equipment and other items incidental to the satisfactory completion of masonry at all depths, heights and levels. Erection and removing of all scaffoldings, ladders and plant required for execution of the work to the height, depth and of any shape directed by the Engineer-in-Charge/Architects. All masonry in line and level, battens, pillars, curves and to any position or shape to required heights including raking of joints, curing etc.
Providing and constructing well burnt brick masonry walls, pillars, steps etc.above 230 mm thick, in CM 1:5 in foundations or plinth and superstructure, raking out joints, watering, curing, etc., all complete. Providing and constructing well burnt brick masonry walls in substructure and superstructure including circular & curved in plan and pillars 230mm thick in CM including using 115 mm thick bricks or 150 mm thick bricks in header bond 1:4, raking out joints, watering, curing, etc., with necessary scaffolding including all lifts and leads all complete.

Providing and constructing half brick masonry walls of 115mm thick in CM 1:4 with RCC runner 75mm thick at every 1.2m height and standards 230 mm wide as required, mix 1:2:4 having 2 No. M.S. 8 dia. longitudinal bars with binders of 6mm dia @ 250 c/c, including shuttering, raking out joints, watering, curing etc., with necessary scaffolding including circular & curved in plan, all lifts and leads etc. all complete. Providing and construction brick masonry walls as in item 2 above but for 150 mm thick.

-do - as 3 above but for solid concrete block masonry 100 mm thick -do - as 3a above but for solid concrete block masonry 150 mm thick

-do - as 2 above but for solid concrete block masonry 200 mm thick Providing and constructing random rubble stone masonry in cement mortar 1:6 in foundations and plinth and in superstructure using approved quality stone and including scaffolding, curing raking of joints etc. all complete Page 7

Sr.No

Description of Item
Area of ashler finish on one or both side as the case is shall be measured and paid for under this item -do- as above but composite masonry with RR stone masonryor brick masonry backing with Nevas stone cladding on one or both sides. Area of ashler finish on one or both side as the case is shall be measured and paid for under this item and RR masonry/brick

Unit

Rate

Remark

- do - as 5a above but for Rough tooled finish stone faces with joints not more than 12 mm with sunk pointing in CM 1:3 - do - as 5b above but for Rough tooled finish stone faces with joints not more than 12 mm with sunk pointing in CM 1:3

Page

Sr.No

Description of Item

Unit

Rate

Remark

SECTION - D : PLASTER Note-:The rate quoted by the Contractor for items under this head shall be Inclusive of the following
A B C D Erection, dismantling and removing scaffolding. Preparing the surfaces to receive plaster. Screening to requierd size and washing sand to remove silt. All labour, materials, use of tools and equipment to complete the plaster with all lifts and leads including curing as directed by Engineer-in-Charge/Architects. Plaster work in bends rounded angles, fair edges, narrow returns, V joints, plays, drip mouldings, grooves, making good the metal frame junctions, jad over skirting or dado making good around pipes, boxes, conduits, railings. Providing and fixing 200 mm wide chicken mesh at junctions of concrete and masonry or any dissimilar materials, and providning and mixing Recron 3S fibre @125 grams per bag of cement in cement mortar for al plaster items. Providing and applying to interior surfaces, walls and ceiling, plain faced cement plaster in C.M. 1:4 with neeroo finish on all types of surfaces specified on drawings at all levels. The rates shall also include moulding and grooves wherever specified, scaffolding, curing, providing and fixing 200 mm wide chicken mesh at junctions of concrete and masonry or any dissimilar materials, and providning and mixing Recron 3S fibre @125 grams 2a. Providing and applying on masonry/concrete 20 mm thick exterior sand faced cement plaster in C.M. 1:3 in two layers, with first layer of 12 mm thickness with waterproofing compound and second layer of 8 mm thickness, using sand of approved quality, size and shade and including providing bands grooves, drip moulds, and including scaffolding, curing etc. complete at all levels. (Approved water proofing compound to be used) providing and fixing 200 mm wide chicken mesh at junctions of concrete and masonry or any dissimilar materials, and providning and mixing Recron 3S fibre @125 grams

1a.

3a

Providing and applying on internal surfaces of masonry / concrete where directed, one coat of plaster up to 15 mm thick in CM 1:4 including curing, scaffolding, providing and fixing 200 mm wide chicken mesh at junctions of concrete and masonry or any diss Providing and applying 12-18 mm thick trowel finished smooth cement plaster in CM 1:4 to internal and external surfaces including curing, scaffolding, providing and fixing 200 mm wide chicken mesh at junctions of concrete and masonry or any dissimilar mat Providing and applying POP smooth punning to walls, of average 12mm thk., punning in proper plumb, line and level, ready to receive paint, with necessary scaffolding and making grooves ( 6 mm ) and edges (corners) as directedPage 9

5a.

Sr.No

Description of Item

Unit

Rate

Remark

SECTION - E : FLOORING Note-:The rates quoted by the Contractor for items under this head shall be Inclusive of the following
A Bc Cleaning the base, providing and laying bedding mortar and levelling, polishing, washing, cleaning etc. All labour, materials and use of tools equipment and machines for carrying out the items. Chiselling, cutting, polishing finishing, cleaning, curing, etc. at all positions with lifts and leads. Backing coat in cement mortar for glazed tiles dado or marble dado or any other wall finish dado. Filling the joints of tiles with neat cement slurry of required colour. Pattern work in tiles or stone work as per drawing including using different size pieces of the same material. For pattern flooring with different material, each material will be measured separately and paid for under that item rate. For Tiles, brands to be used will be first got approved by consultants. Mortar bedding for flooring items will be to the required thickness to make up undulations in the sub base and to match the finished levels of different materials used for flooring in each floor. Finish level of flooring shall be 75 mm above the subfloor level (RCC slab or PCC bedding) to allow for trunking. In case the bedding thickness is more than 30 mm for this, the additional thickness shall be made up using lean concrete screed at contractor

D E F

G H

1a.

1b. 1c. 1d 1e 1f 1g

Supplying and fixing approved quality, pattern, colour, shade, machine cut Kota stone flooring using 450 x 450 x 25 to 35 mm thick stone tiles laid over base of cement sand mortar (1:4) and lean concrete screed so as to have total flooring thickness of 75 and jointed with grey cement slurry mixed with pigment to match the shade of the tile all as specified, including machine polishing mirror finish, curing, finishing etc. complete - do - but for Kota stone of size 600 x 600 x 25 to 35 mm thick - do - as above but for Kota stone skirting 20 mm thick flush with plastered surface of wall etc. complete. - do - but for staircase treads and risers in one piece Kota stone (max 1500 mm long) with all exposed edges machine cut, polished and chamfered. - do - as item 1(d), but for Jaisalmer stone treads and risers and sills. - do - but for sills Kota 20 mm thick - do - as 1a above but for jaisalmer stone flooring Page 10

Sr.No

Description of Item

Unit

Rate

Remark

1h 1i

- do - as 1a above but for Marmonite flooring & skirting - do - as 1a above but for machine cut rough shahabad stone 30-40mm thick for flooring (Hardscaping work) - do - as 1a above but for machine cut polished shahabad stone 30-40mm thick for flooring (Hardscaping work) Extra over item No. 1b above for using kota stone of size 600x1200 mm Providing and fixing fine tooled dressed Nevasa stone in flooring (for Harscape works) - do - as above but for Jaisalmer stone cladding 20 mm thick instaircase as per detail including miror polish, chamfer etc. complete. - do - as above but for Kota stone cladding 20 mm thick instaircase as per detail including miror polish, chamfer etc. complete. Providing and fixing granite 19 mm thick in floors, sills, counter, skirting, dado, treads, risers, cladding etc. as per design and drawing over a base of cement, sand mortar CM 1:4 and jointed with pigment to match the shade of granite as specified and - Do - as above but with granite tiles 8mm thick fixed with chemical adhesive and including epoxy joint 5 mm wide for water bodies or where directed

1j

1k 1l 1m

1n 2a.

2b

3a

Providing & fixing approved quality non skid ceramic tiles of size 300 x 300 mm or 200 x 300 mm in floors over 20 mm base of cement, sand mortar 1:4 and jointed with pigment to match the shade of tiles as specified, including cleaning, curing etc. Same as item No.4a above but glazed or non skid tile for dado including backing coat in CM 1:4. Thickness of backing coat up to 35 mm to suit tile layout with full tiles as per Architects detail drawing. Extra over tile floring for making opening for fixing nahani trap and grating in toilets etc.

3b

3c

Page

11

Sr.No

Description of Item

Unit

Rate

Remark

5a.

Providing & laying 20 mm thick grey cement base marble mosaic tile floor laid over 20 mm thick base of cement sand mortar (1:4) and jointed with white cement slury mixed with pigment to match the shade of the tile all as specified including machine polishing, curing, finishing etc. complete. Supplying and fixing in position 35 mm thick machine cut and machine polished (one or both sides) Cudappa stone for platform supports - vertical and horizontal, counters, shelves etc. all complete. Extra over 6a and 3a above for making opening in granite/cuddapa counter for fixing wash basin including edge polishing, hole for water inlet pipe, protecting the wash basin while edge polishing etc. all complete Providing and fixing in position coping with approved quality stone (Basic price Rs.150/- per sft.) in CM 1:4, including curing, scaffolding, exposed edges machine cut, polished and chamfered as directed. -do- but with rough shahabad stone 65-75 mm thick for coping. (Basic rate of shahabad Rs.25/- per sft.) Providing and fixing flame finished granite in CM 1:4 and jointed with pigment to match the colour of granite, etc. all complete for seats etc.

6a.

6b.

7a

7b

Page

12

Sr.No

Description of Item

Unit

Rate

Remark

SECTION - G : DOORS AND WINDOWS


1 Supplying & fixing Rolling shutters made out of 18 gauge steel sheets for slats including bottom rail, guide channel, lock plates, locking arrangement, fixing bolts, pulling handles hood, rolling arrangement etc. and painting with 2 coats of zinc chromate primer and 2 coats of approved synthetic enamel paint complete as per IS:6248 of approved make.

2a.

Supplying and fixing 35 mm thick solid core flush door shutters, (single/ double), non decorative- type, core of phenol bonded block board with necessary nos. of Brass oxidised hinges with SS pins, construction with frame of first class hard wood, teak lipping and well matchedAnchor 72 Marine ply or equivalent as per IS 710:1976 with both sides enamel painted in three coats. Extra over 2a above for providing aluminum strip under door shutter as per details for toilet doors. Length of al strip will be measured and paid for. Providing & fixing door fittings including all necessary brass oxidised screws etc. complete:

2b

3 (b) Quote percentage of cost for taking possession, fixing in position including providing necessary screws etc., all doors fittings supplied free by Owner and giving reconciliation of items supplied.

4 A B C D E F

Providing & fixing Satin finished 20 micron anodised Aluminium, fully glazed windows, ventilators and partitions of Jindal or equivalent make aluminium sections, using 63 x 37 x 3.18 mm box.'sections for frames and shutters with 50 x 25 x 3.18 mm aluminium box section or heavy duty window shutter sections, with necessary fixtures such as coupling, locking arrangement, 'glazing clips, special gaskets, aluminium beading etc. and including 5 mm th. float Glass and with aluminium sub-frame Louvered window/ventilators with 5.5 mm thick wired glass Partly fixed and partly openable with friction stays. Fixed glazing Sliding windows 2 Tracks Extra over for using frosted glass in place of float galss. Extra over 5(a) for providing aluminum louvres in place of glass

Sr.No

Description of Item

Unit

Rate

Page Remark

13

Replacing broken glass panes of 5 mm thick float glass of above item 5(a) to (f) including removing & disposing broken glass panes, refixing window/vetilator/ partition/ doors frames & panels in original position Extra over item Nos. 4 (a) to (f) for using tinted reflective glass Mercedes Blue shade (Taiwan make) or shade equivalent to existing glass in Phase I of approved make. Providing & fixing structural Glazing of Indian Curtain Syndicate make or equivalent approved make (Grid unitised series 402) with mullion section of 100 x 40 x 2.5 mm th (Wt. 2.3 Kg/Rm), transcom section of 60 x 40 x 2.0 mm th (Wt. 1.5 Kg/Rm) alloy 6063 Extra over Item No. 8 above for providing Sliding/Side Hung Door within the structural glazing panel. Providing and fixing 12 mm thick toughened glass fixed glazing with anodised Aluminum channel at top and bottom support, sealing glass joints with sealant etc. all complete as detailed.

6 7

Sr.No

Description of Item

Unit

Rate

Page Remark

14

SECTION H : PAINTING & POLISHING


1a. Supplying and providing two coats of approved quality and make water proof cement based paint, Snowcem or equivalent, finished over a coat of primer on all exterior surfaces in approved shade and colour as directed and as per manufacturers instructions including surface preparation, all scaffolding etc. complete at all levels. Providing and applying waterprof cum decorative exterior paint "Pro-Dcor Damp Proofer" of Chemistick make (PDDP) or approved equivalent paint to external surfaces including surface preparation, primer coat, sealing hairline cracks and 2 coats of PDDP as

Sqm

1b.

Sqm

1c. 2

Same as 1a above but using acrylic exterior paint (Apex or approved equivalent). Providing and applying on interior surfaces two coats of paint of approved manufacturer and shade over a coat of approved primer as directed by Engineer including surface preparation, staging, scaffolding, etc. complete at all levels for (Rate to include surface preparation, filling crevices with putty etc. complete) Oil bound distemper Plastic emulsion paint Oil paint (synthetic enamel) on internal or external surfaces Lustre paint 1 coat cement paint dark grey above false ceiling

Sqm

A B C D E

Sqm Sqm Sqm Sqm Sqm

Providing and applying on Interior surfaces three coats of white wash/colour wash over surface prepared with puttyas specified to give good even shade including scaffolding, mixing glue to prevent staining etc. complete. Providing and applying epoxy paint to MS structures / surfaces including necessary primer etc. all complete. Providing and applying synthetic enamal paint to MS structure of all coloumn,trusses and Purlins etc complete Only primer Only primer plus two coat of paint Only one coat of paint

Sqm Sqm

Sr.No

Description of Item

Unit

Rate

Page Remark

15

SECTION - J : ROOFING & RAIN WATER PIPES


Note-:The rates quoted by Contractor under this head shall be inclusive of: A B C Use of I.S.I. approved material duly tested and approved by Local Authority. Coordination with other agencies working at site. Holes in the walls or chajjas shall be made good as per the surround surface and shall not be paid any extra. Rain Water Pipes shall be fixed with necessary spacers and GI clamps, so as to leave a gap of minimum 50 mm between pipe & wall to enable proper painting of wall & pipe surfaces in future. Providing, jointing and fixing half round 150 mm dia. heavy duty SWR pipe drain in masonry channel as directed. Providing and fixing 160 mm OD (4Kg.) HDPE pipe as sleeve for FO cables etc. under floors, in concrete etc. Supplying and laying, jointing, and hydraulically testing cement concrete pipes NP 2 class conforming to IS 458 for storm water drains, cable crossings, including collars joined in CM 1:2 for a) 150 mm dia b) 250 mm dia c) 300 mm dia

d) 600 mm dia 4 Providing and fixing 75 mm dia PVC pipe as weep holes in stone masonry walls and finishing the opening in granite and shahabad stone as per drawing etc. all complete. Providing and fixing CI grating suitable for 150 mm dia pipe on roof slab/gutter etc. complete including making the junction with slab watertight. The level to be maintained such as water flows out easily from the terrace/gutter. Same as 5a above but suitable for 100 mm dia. pipe Same as 5a above but suitable for 200 mm dia. pipe Page Remark 16

5a.

5b. 5c

Sr.No

Description of Item

Unit

Rate

6a.

Providing & jointing and fixing at all levels 150 mm dia. heavy duty SWR rain water down take pipe with clamps including bends, tees, junctions, adopters, shoes and including scaffolding etc. complete Same as 6a above but for 100 mm dia pipe. Same as 6a above but for 200 mm dia pipe. Providing & fixing at all levels 2 mm thick lead flashing of shape and size as shown on drawings or as directed by Engineer including necessary fixtures complete Construction masonry open surface drains in 230mm thick brick masonry in C.M 1:5, cement concrete bed 150 mm thick in M150 concrete, plastering in C.M. 1:4 etc., with heavy duty C.I grating with nosing of 30 mm x 30 mm x 5 mm thick etc. complete to prope

6b. 6c. 7

Sr.No

Description of Item

Unit

Rate

Page Remark

17

SECTION - K : MISCELLANEOUS WORKS


1 Demolishing RCC/PCC Work in superstructure and sub structure (taking all necessary precautions) including transporting and disposal of only broken concrete anywhere in Site for filling low lying areas, cold cutting reinforcing bars cleaning and stacking of serviceable material and transporting the same as directed and disposal of unserviceable materials at designated location, inside site premises (excavation paid separately).

Demolishing masonry work in superstructure and substructure (taking all precautions) including transporting and disposal of broken pieces in Site and stacking as directed complete. Core drilling in RCC slab of upto 150 mm dia & 225 mm deep Making openings in masonry walls upro 0.5 SM area for HVAC ducts etc. and making good the same with necessary plaster to match adjoining areas

3 4

Вам также может понравиться