Академический Документы
Профессиональный Документы
Культура Документы
R2 Description
R2 Signaling is a CAS (Channel Associated Signaling) protocol that was developed in the 1960s, but is still used today in Europe, Asia, Latin America, and Australia. The R2 signaling specification is fully defined in the International Telecommunications Union (ITU) Telecommunication Standardization Sector (ITU-T) Recommendations Q.400 through Q.490. This document does not provide the full definition, but only touches upon the basic information. Although R2 signaling has been defined in ITU-T Q.400-Q.490 recommendations, there are many variations in how R2 is implemented. Various countries have chosen to implement R2 differently. So while some carriers may tell you to just use the CCITT standard, there are many variations to this standard and more specific information may be needed. There are two elements to R2 Signaling. They are Line Signaling (supervisory signals) and Inter-register Signaling (call setup/control signals). They are further explained below.
Transition A,B: 1,0 A,B: 0,0 A,B: 1,0 A,B: 1,1 A,B: 0,1 A,B: 0,1 0,0 1,0 1,1 0,1 1,1 1,0
The line signaling is defined with the following types. R2-Digital R2 Line Signaling using ITU-U Q.421. Typically used for PCM systems where A and B bits are used. R2-Analog ITU-U Q.411 standard. Used for carrier systems where a Tone A bit is used. R2-Pulse ITU-U Supplement 7. For systems that use satellite lings where a Tone A bit is pulsed.
Page 1 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Figure 1
Forward Signal Groups Group-I Signals - Represent the called party number or dialed digits. - DNSI/ANI digits. - I-1 to I-10 are digits 1 to 10. - I-15 is the end of identification.
Backward Signal Groups Group-A Signals - Indicate if the signaling ended or if a particular forward signal is required. - Used to acknowledge and convey signaling information. - A-1 is to send next digit. - A-3 is address complete, change to Group B signals. - A-4 is congestion. - A-5 is to send calling partys category. - A-6 is address complete, charge, setup, speech conditions. Group-B Signals - Sent by the termination switch to acknowledge a forward signal, or to provide a call charging and called party information. - Used to acknowledge Group-II forward signals. This is always preceded by an address complete signal A-3. - B-3 is subscriber line busy. - B-4 is congestion. - B-5 is unallocated number. - B-6 is subscribers line free charge.
Table 2
Group-II Signals - Represent the calling party category. - II-1 is subscriber without priority. - II-2 to II-9 are subscriber with priority. - II-11 to II-15 are spare for national use.
The following sequence rules are used to identify the signal group. The initial signal received by the incoming exchange is a Group I signal. The outgoing exchanges consider backward signals as Group A signals. The Group A signals received by outgoing exchanges are used to identify whether the next signal is a Group B signal. The Group B signals always indicate an end-of-signaling sequence.
Page 2 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
There are three types of inter-register signaling. R2-Compelled When a tone-pair is sent from the switch (forward signal), the tones stay on until the remote end responds/ACK back with a pair of tones that signals the switch to turn off the tones. The tones are compelled to stay on until they are turned off. R2-Non-Compelled The tone-pairs are sent (forward signal), as pulses so they stay on for a short duration. Responses (backward signals) to the switch (Group B) are sent as pulses. There are no Group A signals in non-compelled signaling. R2-Semi-Compelled - Forward tone-pairs are sent as compelled. Responses (backward signals) to the switch are sent as pulses. It is the same as compelled, except that the backward signals are pulsed instead of continuous.
NOTE Current software on the Tenor only supports MFC or Multi-Frequency Compelled R2.
1001
Page 3 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
R2 Specific Parameters
This section describes the R2 protocol related parameters implemented in the Tenor and the CMS. Using appropriate values supports country variations of R2 protocol. When you are looking to implement R2 signaling, the information below will be needed from your PSTN provider to accurately configure the Tenor/CMS to correctly signal. The actual command syntaxes will be shown later in this document.
Page 4 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Page 5 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
r2sigbits
Description Prompt Level Syntax Argument This parameter enables you to set both the CD bits and the inverted bits as explained above. config pstntg 1# or config pbxtg 1# r2sigbits or r2sig {cd-bits} {invert-bits] cd-bits Numeric value that indicates the binary setting of the C & D bits. Valid entries are from 0 (0000) to 3 (0011). ABCD 0 = 0000 1 = 0001 2 = 0010 3 = 0011 Numeric value that indicates the binary setting of what bits (A, B, C & D) to be inverted. Valid entries are 0 (0000) through 15 (1111). 0 = 0000 1 = 0001 2 = 0010 3 = 0011 4 = 0100 5 = 0101 6 = 0110 7 = 0111 8 = 1000 9 = 1001 10 = 1010 11 = 1011 12 = 1100 13 = 1101 14 = 1110 15 = 1111
invertbits
None None All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2sigbits 3 0 Sets the C bit to 1 and the D bit to 1 (3 = 0011) and no bits are inverted (0 = 0000). config pstntg 1# r2sigbits 1 5 Sets the C bit to 0 and the D bit to 1 (1 = 0001) and the B and D bits are inverted (5 = 0101).
Example
Page 6 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
r2dnis
Description Prompt Level Syntax Arguments Used to set the DNIS Length, answer tone and the 1st digit request tone. config pstntg 1# or config pbxtg 1# r2dnis or r2dn {len} {anstone} {1stdig} len anstone 1stdig len anstone 1stdigit Default Availability None All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2dnis 0 3 5 Sets the DNIS length to variable, answer tone to A3 and the 1st digit tone to 5. config pstntg 1# r2dnis 7 6 0 Sets the DNIS length to 7 digits only, answer tone to A6 and no 1st digit tone. Required. Numeric value that specifies the DNIS length expected. Required. Numeric value that specifies the normal group A answer tone. Required. Numeric value that specifies the send 1st digit tone. 0 1-20 3 or 6 0 1-15 Variable DNIS length used. Number indicates the specific DNIS length expected. Specifies the group A tone to be used. 3 = A3 and 6 = A6. 1st digit request tone is not used. Specifies the group A backward tone to request the 1st digit.
Settings
Example
r2ani
Description Prompt Level Syntax Arguments Used to set R2 ANI request, ANI length, ANI category and the ANI tones as described above. config pstntg 1# or config pbxtg 1# r2ani or r2an {req} {len} {cat} {tone} req len cat tone Settings req Required. Numeric value that specifies whether and when ANI should be requested. See settings below for more information. Required. Numeric value that specifies how many digits the ANI (if requested) will be. Required. Numeric value that specifies backward group A tone used to request the calling party category before the ANI digits. Required. Numvberic value that specifies the backward group A tone used to request the ANI digits. 0 1-20 -1 0 1-20 1-15 1-15 Do not request ANI. Request ANI after the specified DNIS digits. Request ANI after complete DNIS is receive. Variable ANI length. Specified ANI length. Specified backward group A tone for category. Specified backward group A tone for the ANI.
Page 7 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Default Availability
None All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2ani 7 0 1 1 Sets the ANI to be requested after the 7th DNIS digit is received, ANI will be variable length, backward tone A1 will be used to request the ANI category and backward tone A1 will be used to request the ANI. config pstntg 1# r2ani 1 7 2 2 Sets the ANI to be requested after the all DNIS digit have been received, ANI will be 7 digits in length, backward tone A2 will be used to request the ANI category and backward tone A2 will be used to request the ANI.
Example
r2category
Description Used to set the R2 Group I forward tone for ANI category request and the group II forward tone to be sent on receiving an A3 backward tone for the calling party category. config pstntg 1# or config pbxtg 1# r2category or r2cat {ani} {cp} ani cp Required. Numeric value that specifies the group I forward tone to be sent. Required. Numeric value that specifies the group II forward tone to be sent. 1-15 1-15 Specific group I tone to be sent (I-1 through I-15). Specific group I tone to be sent (II-1 through II-15).
ani cp None
All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2cat 6 1 Sets the group I tone to I1 and the category tone to II1.
Example
r2group-b
Description Prompt Level Syntax Used to set the R2 Group B tones. They include, idle tone sent, idle tone received, busy tone sent and busy tone received. config pstntg 1# or config pbxtg 1# r2group-bor r2group {txidle} {txbusy} {rxidle} {rxbusy}
Page 8 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Arguments
Required. Numeric value that specifies the group B tone to be sent when the line is free. Required. Numeric value that specifies the group B tone to be sent when the line is busy. Required. Numeric (decimal) value that specifies the binary value of the group B tones to be received when the line is free. Required. Numeric (decimal) value that specifies the binary value of the group B tones to be received when the line is busy. 1-8 1-8 0-255 0-255 Specific group B tone to be sent (B-1 through B-8). Specific group B tone to be sent (B-1 through B-8). Specific group B tones (can be more than one, B1-B8) in a bit map that will be received. See guidelines below. Specific group B tones (can be more than one, B1-B8) in a bit map that will be received. See guidelines below.
Settings
Default Availability
None All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). A bit map is used to enter the rxidle and rxbusy tones in since more than one tone can be used. The bit map should look as follows; B8 B7 B6 B5 B4 B3 B2 B1 8 7 6 5 4 3 2 1 Once you have determined the correct B-tones for this parameter, you would set the corresponding bits to a 1 and any tones not used should be set to 0. Then convert the binary number to a decimal and enter this value in for the parameter. For example, to set the tones to B7 B5 and B2, the bit map would look like: B8 B7 B6 B5 B4 B3 B2 B1 0 1 0 1 0 0 1 0 = 01010010 = decimal 82 When you do a print of the results in the trunk group, the sequence will be txidle, rxidle, txbusy, rxbusy, which is different from the order you entered this. config pstntg 1# r2group 1 3 33 14 Sets txidle to B1, txbusy to B3, rxidle to B6 and B1, and rxbusy to B4, B3 and B2.
Guidelines
Example
r2default-ani
Description Prompt Level Syntax Arguments Default Availability Used to set the default ANI to be sent if no ANI is available to send. config pstntg 1# or config pbxtg 1# r2default-ani or r2def {number} number None All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2default 7325551000 Sets the default ANI to 7325551000. Optional. Numeric string (up to 12 digits) sent as the default ANI.
Example
Page 9 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
r2timeouts
Description Prompt Level Syntax Arguments Used to set the seizure and release guard timeouts. config pstntg 1# or config pbxtg 1# r2timeout or r2time {seiz} {rel} seiz Required. Numeric value, in milliseconds, that specifies the maximum time an outgoing R2 register waits for the seizure acknowledgement after sending a seizure signal. Required. Numeric value, in milliseconds, that specifies the time an incoming R2 register waits before sending an idle line signal.
Seizure = 200 Release = 0 All Digital Tenor Releases. Only when t1ore1 (config line 1 1# or config line 1 2# prompt) = e1(1), ccsorcas (pbxtg or pstntg) is set to CAS(1) and cassig is set to R2(4). config pstntg 1# r2time 300 10 Sets the Seizure to 300ms and the release guard to 10ms.
Example
CdBits
Description Prompt Level Syntax Arguments This parameter will enable you to set what the C & D bits will be set to for R2. config CASSignalingGroup set cdbits or set cd {cd-bits} cd-bits Numeric value that indicates the binary setting of the C & D bits. Valid entries are from 0 (0000) to 3 (0011). ABCD 0 = 0000 1 = 0001 2 = 0010 3 = 0011
None All CMS Releases. config CASSignalingGroup 1# set cd 3 Sets the C bit to 1 and the D bit to 1 (3 = 0011). config CASSignalingGroup 1# set cd 1 Sets the C bit to 0 and the D bit to 1 (1 = 0001).
Page 10 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
InvertABCD
Description Prompt Level Syntax Arguments Allows you to specify which, if any, bits are to be inverted. config CASSignalingGroup set invertabcd or set iabcd {invert} invert Numeric value that indicates the binary setting of what bits (A, B, C & D) to be inverted. Valid entries are 0 (0000) through 15 (1111). 0 = 0000 1 = 0001 2 = 0010 3 = 0011 4 = 0100 5 = 0101 6 = 0110 7 = 0111 8 = 1000 9 = 1001 10 = 1010 11 = 1011 12 = 1100 13 = 1101 14 = 1110 15 = 1111
None All CMS Releases. config CASSignalingGroup 1# set iabcd 5 Sets the B and D bits to invert (5 = 0101). config CASSignalingGroup 1# set iabcd 9 Sets the A and D bits to be inverted (9 = 1001).
ReqCatDigit
Description Prompt Level Syntax Arguments Used to set the backward group A tone that will be sent to request the calling party category before the ANI digits. config CASSignalingGroup set reqcatdigit or set rcd {cat} cat Required. Numeric value that specifies backward group A tone used to request the calling party category before the ANI digits. 1-15 Specified backward group A tone for category.
cat None
All CMS Releases. config CASSignalingGroup 1# set rcd 2 Sets the category request tone to A2.
ReqANIDigit
Description Prompt Level Syntax Arguments Settings Used to set the backward group A tone used to request the ANI digits. config CASSignalingGroup set reqanidigit or set ranid {ani} ani ani Numeric value that specifies the backward group A tone used to request the ANI digits. 1-15 Specified backward group A tone for the ANI.
Page 11 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
None All CMS Releases. config CASSignalingGroup 1# set ranid 5 Sets the ani request tone to A5.
ANsDigit
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the group A tone used to answer incoming calls. config CASSignalingGroup set ansdigitor set and {ans} ans ans None All CMS Releases. config CASSignalingGroup 1# set and 3 Sets the group A answer tone to A3. Numeric value that specifies the backward group A tone used to request the ANI digits. 3 or 6 Specifies the group A tone to be used. 3 = A3 and 6 = A6.
Send1stDigit
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the group A backward tone used to indicate whether to send first digit. config CASSignalingGroup set send1stdigit or set s1d {1st} 1st 1ist None All CMS Releases. config CASSignalingGroup 1# set s1d 5 Sets the group A send first digit tone to A5. config CASSignalingGroup 1# set s1d 0 Indicates that the send 1st digit tone will not be used. Numeric value that specifies the backward group A tone used to send the first digit. 0 1-15 1st digit request tone is not used. Specifies the group A backward tone to request the 1st digit.
GbIdleSent
Description Prompt Level Syntax Arguments Used to set the group B transmitted idle tone. config CASSignalingGroup set gbidlesent or set gis {txidle} txidle Numeric value that specifies the group B tone to be sent when the line is free.
Page 12 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
txidle None
1-8
All CMS Releases. None config CASSignalingGroup 1# set gis 5 Sets the group B idle tone transmit to B5. config CASSignalingGroup 1# set gis 1 Sets the group B idle tone transmit to B1.
GbBusySent
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the group B transmitted busy tone. config CASSignalingGroup set gbbusysent or set gbs {txbusy} txbusy txbusy None All CMS Releases. config CASSignalingGroup 1# set gbs 5 Sets the group B busy tone transmit to B5. config CASSignalingGroup 1# set gbs 1 Sets the group B busy tone transmit to B1. Numeric value that specifies the group B tone to be sent when the line is busy. 1-8 Specific group B tone to be sent (B-1 through B-8).
A6Cat
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the group I forward tone to be sent on receiving calling party category request before the ANI digit request is sent. config CASSignalingGroup set a6cat or set a6c{a6cat} a6cat a6cat None All CMS Releases. config CASSignalingGroup 1# set a6c 5 Sets the group I tone to I5. config CASSignalingGroup 1# set a6c 1 Sets the group I tone to I1. Numeric value that specifies the group I forward tone to be sent. 1-15 Specific group I tone to be sent (I-1 through I-15).
Page 13 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
A3Cat
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the group II forward tone to be sent on receiving A-3 backward tone. This indicates the category of the calling party. config CASSignalingGroup set a3cat or set a3c{a3cat} a3cat a3cat None All CMS Releases. config CASSignalingGroup 1# set a3c 5 Sets the group II tone to II5. config CASSignalingGroup 1# set a3c 1 Sets the group II tone to II1. Numeric value that specifies the group II forward tone to be sent. 1-15 Specific group II tone to be sent (II-1 through II-15).
DNISLen
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the length of the incoming DNIS or dialed number. config CASSignalingGroup set dnislen or set dnisl{len} len len None All CMS Releases. config CASSignalingGroup 1# set dnisl 0 Sets the DNIS length to variable. config CASSignalingGroup 1# set dnis1 12 Sets the DNIS length to 12 digits. Numeric value that specifies the DNIS length expected. 0 1-20 Variable DNIS length used. Number indicates the specific DNIS length expected.
ReqANI
Description Prompt Level Syntax Arguments Settings Used to specify whether ANI should be requested and when it should be requested. config CASSignalingGroup set reqani or set rani{req} req req Required. Numeric value that specifies whether and when ANI should be requested. See settings below for more information. 0 1-20 -1 Do not request ANI. Request ANI after the specified DNIS digits. Request ANI after complete DNIS is received
Default Availability
Page 14 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Example
config CASSignalingGroup 1# set rani 0 No ANI is to be requested. config CASSignalingGroup 1# set rani 3 ANI is to be requested after the 3rd DNIS digit is sent. config CASSignalingGroup 1# set rani -1 ANI is to be requested after all DNIS digits are delivered.
ANILen
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to specify number of digits for the ANI. config CASSignalingGroup set anilen or set anil{len} len len None All CMS Releases. config CASSignalingGroup 1# set anil 0 ANI length will be variable. config CASSignalingGroup 1# set anil 7 ANI length will be 7 digits. Numeric value that specifies the digit length of the incoming ANI. 0 1-20 Variable ANI length. Specified ANI length.
GbIdleRcvdBits
Description Prompt Level Syntax Arguments Settings Default Availability Guidelines Used to set the group B idle tones received. config CASSignalingGroup set gbidlercvdbits or set girb{rxidle} rxidle rxidle None All CMS Releases. A bit map is used to enter the rxidle and rxbusy tones since more than one tone can be used. The bit map should look as follows. B8 B7 B6 B5 B4 B3 B2 B1 8 7 6 5 4 3 2 1 Once you have determined the correct B-tones, set the corresponding bits to 1 and any tones not used should be set to 0. Then convert the binary number to a decimal and enter this value. For example, to set the tones to B7 B5 and B2, the bit map would look like this. B8 B7 B6 B5 B4 B3 B2 B1 0 1 0 1 0 0 1 0 = 01010010 = decimal 82. config CASSignalingGroup 1# set girb 33 Sets the receive idle tones to B6 and B1 tones. Numeric (decimal) value that specifies the binary value of the group B tones to be received when the line is free. 0-255 Specific group B tones (can be more than one, B1-B8) in a bit map that will be received. See guidelines below.
Example
Page 15 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
GbBusyRcvdBits
Description Prompt Level Syntax Arguments Settings Default Availability Guidelines Used to set the group B busy tones received. config CASSignalingGroup set gbbusyrcvdbits or set gbrb{rxbusy} rxbusy rxbusy None All CMS Releases. A bit map is used to enter the rxidle and rxbusy tones in since more than one tone can be used. The bit map should look as follows. B8 B7 B6 B5 B4 B3 B2 B1 8 7 6 5 4 3 2 1 Once you have determined the correct B-tones for this parameter, set the corresponding bits to 1 and any tones not used should be set to 0. Then convert the binary number to a decimal and enter this value. For example, to set the tones to B7 B5 and B2, the bit map would look like this. B8 B7 B6 B5 B4 B3 B2 B1 0 1 0 1 0 0 1 0 = 01010010 = decimal 82. config CASSignalingGroup 1# set gbrb 14 Sets the receive busy tones to B4, B3 and B2. Numeric (decimal) value that specifies the binary value of the group B tones to be received when the line is busy. 0-255 Specific group B tones (can be more than one, B1-B8) in a bit map that will be received. See guidelines below.
Example
RelGuardTime
Description Prompt Level Syntax Arguments Default Availability Example Used to specify the number of milliseconds for the release guard timeout. config CASSignalingGroup set relguardtime or set rgt{rel} rel None All CMS Releases. config CASSignalingGroup 1# set rgt 500 Sets the release guard to 500ms. Numeric value, in milliseconds, that specifies the time an incoming R2 register waits before sending an idle line signal.
SeizureAckTime
Description Prompt Level Syntax Used to specify the number of milliseconds for the seizure acknowledgment. config CASSignalingGroup set seizureacktime or set sat{seiz}
Page 16 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Arguments
seiz
Numeric value, in milliseconds, that specifies the maximum time an outgoing R2 register waits for the seizure acknowledgement after sending a seizure signal.
200 All CMS Releases. config CASSignalingGroup 1# set sat 500 The Seizure ack time will be 500ms.
DefaultANI
Description Prompt Level Syntax Arguments Settings Default Availability Example Used to set the default ANI to be sent if no ANI is available to send. config CASSignalingGroup set defaultani or set dani{ani} ani None None All CMS Releases. config CASSignalingGroup 1# set dani 7325551000 Sets the default ANI to 7325551000. Numeric string (up to 12 digits) that will be sent as the default ANI.
Page 17 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Algeria R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments I-1 II-1 150ms 600ms
1
Settings 0001 0000 9 digits1 A-6 1 B-6 B-3 B-2 & B-3 B-1 & B-2 Do not request ANI
CMS Command set cdbit 1 set iabcd 0 set dnisl 9 set and 6
r2dnis 9 6 1
r2group 6 3 6 3
r2ani 0 set a6c 1 r2categ 1 1 r2time 150 600 set a3c 1 set sat 150 set rgt 600
Page 18 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Brazil R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Default ANI Comments Settings 0001 0000 Variable A-6 Not Used B-6 B-3 B-1 , B-6 & B-7 B-3 After A-5 A-5 I-1 II-1 2000 ms 0 ms Note 1 r2time 2000 0 r2def xxxxxxxx r2categ 1 1 r2ani 2 0 5 5 2nd DNIS digit Variable r2group 6 3 97 4 r2dnis 0 6 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 6 set s1d 0 set gis 6 set gbs 3 set girb 97 set gbrb 4 set rani 2 set anil 0 set rcd 5 set ranid 5 set a6c 1 set a3c 1 set sat 2000 set rgt 0 set dani xxxxxxxx
1. Must enter a Default ANI in case one is not present when sending calls out of this R2 line.
Page 19 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Page 20 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
China R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0011 0000 71 A-3 Not Used B-1 B-3 B-1 & B-6 B-2, B-3 & B-4 After DNIS Variable A-6 A-1 I-1 II-1 300ms 0ms
1
CMS Command set cdbit 3 set iabcd 0 set dnisl 7 set and 3
r2dnis 7 3 0
r2group 1 3 33 14
set ranid 1 set a6c 1 set a3c 1 set sat 300 set rgt 0
Page 21 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Egypt R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable A-3 Not Used B-6 B-3 B-1 , B-6 & B-7 B-3 After A-6 A-1 I-1 II-1 200ms 0ms r2time 200 0 r2categ 1 1 r2ani 1 0 6 1 1st digit Variable r2group 6 3 97 4 r2dnis 0 3 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 97 set gbrb 4 set rani 1 set anil 0 set rcd 6 set ranid 1 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 22 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Ghana R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Settings 0001 0000 Variable A-3 Not Used B-6 B-3 B-1 & B-6 B-1, B-6 & B-7 After complete DNIS Variable A-5 A-5 I-7 II-2 2000ms 0ms r2time 2000 0 r2categ 7 2 r2ani -1 0 5 5 r2group 6 3 97 4 r2dnis 0 3 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 33 set gbrb 4 set rani -1 set anil 0 set rcd 5 set ranid 5 set a6c 7 set a3c 2 set sat 2000 set rgt 0
Page 23 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
India R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 3 digits1 A-6 Not Used B-1 B-3 B-1 & B-6 B-2, B-3 & B-4 After complete DNIS Variable A-6 A-1 I-1 II-1 200ms 0ms
1
CMS Command set cdbit 1 set iabcd 0 set dnisl 3 set and 6
r2dnis 3 6 0
r2group 1 3 33 14
set ranid 1 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 24 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Iraq R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable A-3 Not Used B-6 B-3 B-1 , B-6 & B-7 B-3 Not Used Variable A-5 A-5 I-1 II-1 200ms 0ms r2time 200 0 r2categ 1 1 r2ani 0 0 5 5 r2group 6 3 97 4 r2dnis 0 3 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 97 set gbrb 4 set rani 0 set anil 0 set rcd 5 set ranid 5 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 25 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Korea R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable A-3 Not Used B-6 B-3 B-1, B-6 & B-7 B-3 Do not request ANI Variable A-1 A-1 I-1 II-1 200 ms 0 ms r2time 200 0 r2categ 1 1 r2ani 0 0 1 1 r2group 6 3 97 4 r2dnis 0 3 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 97 set gbrb 4 set rani 0 set anil 0 set rcd 1 set ranid 1 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 26 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Kuwait R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable A-6 A-2 B-5 B-2 B-1, B-5 & B-6 B-2 After complete DNIS Variable A-6 A-2 I-6 II-2 4000ms 165ms r2time 4000 165 r2categ 6 2 r2ani -1 0 6 2 r2group 5 2 49 2 r2dnis 0 6 2 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 6 set s1d 2 set gis 5 set gbs 2 set girb 49 set gbrb 2 set rani -1 set anil 0 set rcd 6 set ranid 2 set a6c 6 set a3c 2 set sat 4000 set rgt 165
Page 27 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Mexico R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable1 A-3 Not Used B-1 B-3 B-1, B-6 & B-7 B-42 Do not request ANI Variable A-1 A-1 I-1 II-1 3500 ms 500 ms
1 2
CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3
r2dnis 0 3 0
r2group 1 3 97 4
set ranid 1 set a6c 1 set a3c 1 set sat 3500 set rgt 500
Have seen this set to 8 digits before. Please check with carrier. Have seen this set to B-3 as well.
Page 28 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Mongolia R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0000 0000 Variable A-3 Not Used B-6 B-3 B-6 B-3 After A-5 A-5 I-1 II-1 150ms 600ms
1
CMS Command set cdbit 0 set iabcd 0 set dnisl 0 set and 3
r2dnis 0 3 0
set ranid 5 set a6c 1 set a3c 1 set sat 150 set rgt 600
Page 29 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Philippines R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0001 0000 Variable A-3 Not Used B-6 B-3 B-1, B-6 & B-71 B-3 After complete DNIS Variable A-5 A-5 I-1 II-1 1000 ms 0 ms
1
CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 3
r2dnis 0 3 0
r2group 6 3 97 4
set ranid 5 set a6c 1 set a3c 1 set sat 1000 set rgt 0
Page 30 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Romania R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0011 0000 Variable A-3 Not Used B-6 B-3 B-6 B-3 After first DNIS Digit Variable A-5 A-5 I-1 II-1 200 ms 0 ms r2time 200 0 r2categ 1 1 r2ani 1 0 5 5 r2group 6 3 32 4 r2dnis 0 3 0 r2sig 3 0 Tenor command CMS Command set cdbit 3 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 32 set gbrb 4 set rani 1 set anil 0 set rcd 5 set ranid 5 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 31 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Page 32 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Singapore R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments Settings 0011 0000 Variable A-3 Not Used B-6 B-3 B-1 & B-6 B-3 After first DNIS Digit Variable A-5 A-5 I-1 II-1 200 ms 0 ms r2time 200 0 r2categ 1 1 r2ani 1 0 5 5 r2group 6 3 33 4 r2dnis 0 3 0 r2sig 3 0 Tenor command CMS Command set cdbit 3 set iabcd 0 set dnisl 0 set and 3 set s1d 0 set gis 6 set gbs 3 set girb 33 set gbrb 4 set rani 1 set anil 0 set rcd 5 set ranid 5 set a6c 1 set a3c 1 set sat 200 set rgt 0
Page 33 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Zaire R2 Settings
R2 Parameter CD-Bits Invert-Bits DNIS Length Answer Tone Send 1st Digit Group B Xmt Idle Tone Group B Xmt Busy Tone Group B Rcv Idle Tones Group B Rcv Busy Tones ANI Request ANI Length ANI Category Request Tone ANI Tone Request ANI Category ANI Calling Party Category Seizure Ack Timeout Release Guard Timeout Comments NOTE Additional country specific R2 settings will be added to our web site as they become available. Settings 0001 0000 Variable A-6 Not Used B-6 B-3 B-1, B-6 & B-7 B-3 After complete DNIS Variable A-5 A-5 I-1 II-7 200 ms 0 ms r2time 200 0 r2categ 1 7 r2ani -1 0 5 5 r2group 6 3 97 4 r2dnis 0 6 0 r2sig 1 0 Tenor command CMS Command set cdbit 1 set iabcd 0 set dnisl 0 set and 6 set s1d 0 set gis 6 set gbs 3 set girb 97 set gbrb 4 set rani -1 set anil 0 set rcd 5 set ranid 5 set a6c 1 set a3c 7 set sat 200 set rgt 0
Page 34 of 35
Quintum Technical Assistance Center (QTAC) 71 James Way Eatontown, NJ 07724 USA
Group B Idle Tone The group B backward tone sent by incoming register to indicate idle Sent condition of the destination party. Group B Busy Tone Sent The group B backward tone sent by incoming register to indicate busy condition of the destination party.
Group B Idle Tone The group B backward tones received by outgoing register to indicate Received. the idle condition of the destination party. Multiple tones used. Group B Busy Tone Received ANI Request ANI Length ANI Category Request Tone ANI Category Tone Calling Party Category Seizure Ack Release Guard The group B backward tones received by outgoing register to indicate the busy condition of the destination party. Multiple tones used. Indicate when (if used) ANI will be requested. Specify either not used, after complete DNIS or the specific DNIS digit received to request ANI. Specify the ANI length. Can be variable or a specified length. Specify the group A backward tone used to request the calling party category before ANI. Specify the Group I forward tone to be used to indicate the category of the ANI when category request tone is received. Specify the Group II forward tone to be sent on receiving A-3 backward tone. Specify the time, in milliseconds, for the seizure ack. Specify the time, in milliseconds, for the release guard.
ANI Request Tone Specify the group A backward tone used to request the ANI digits.
Page 35 of 35