Академический Документы
Профессиональный Документы
Культура Документы
Innolux Display Corporation Industry District 10, LongHua, Shen, Ch T.L +86-0755-27706888 www.innolux.com
Sandan.Deng 5/15/2008
Page 1
Record of Revision
Version Revise Date A 2009/02/19 Page Content New version and standardization
Sandan.Deng
Page 2
5/15/2008
1.
1.1
Module Introduction
Module photo
Module photo Top side Bottom side
Module name
AT102TN42
1.2
Module table
Module name
AT102TN42
Interface
LVDS
Brightness(nits)
200
Pin Num.
30 pin
Recommended connector
MDF76KBW-30S-1H
2.
Symbol
VCC VCC VEDID SCL SDA VSS VSS Rin0Rin0+ VSS
Pin No.
11 12 13 14 15 16 17 18 19 20
Symbol
Rin1Rin1+ VSS Rin2Rin2+ VSS ClkINClkIN+ VSS Rin3-
Pin No.
21 22 23 24 25 26 27 28 29 30
Symbol
Rin3+ VSS VLED VLED GLED GLED NC NC ADJ* DTH
Sandan.Deng
Page 3
5/15/2008
Note1: Data Signal includes Rin0- ~ Rin3-, Rin0+ ~ Rin3+, CLKIN- , CLKIN+. Note2: 10ms t1 0.5 ms; 50ms t2 0ms; 50ms t3 0ms; t4 500ms; t5 200 ms; t6 50ms
3.2
Customer should notice the red mark specially, if you do not follow it, it would lead to display abnormal.
Sandan.Deng
Page 4
5/15/2008
Values Symbol Item VCC Power Voltage VLED ICC Current Consumption ILED Differential Input High Threshold Differential Input Low Threshold VTHLVDS VTLLVDS -100.0 700 850 100.0 10.0 mA mV mV A VIN=2.4V or 0V VCC =3.6V VCC =3.3V Ta=+25 Note 4 Note 3 Vcm=1.2V 4.8 5.0 370 5.2 420 V mA Note 2 Min. 3.1 Typ. 3.3 Max. 3.5 V Note 1 Unit Remark
LVDS Receiver Input IIN Current LVDS Receiver Input VCM Common Voltage LED life time -
0.2 10,000
1.9 -
V Hr
Note 1: VCC setting should match the signals output voltage of customers system board. Note 2: LED driving voltage. Note 3: LED driving current. Note 4: The LED life time is defined as the module brightness decrease to 50% original brightness at Ta=25 and VLED =5.0V. The LED lifetime could be decreased if operating VLED is larger than 5.0V.
3.3
Timing characteristic.
Input signals must follow our timing specification, Otherwise the LCM will display abnormally. About the detail timing parameters of LCD display, please follow the product specification.
Sandan.Deng
Page 5
5/15/2008
3.3.1
AT102TN42 has integrated LVDS to TTL T-con IC into our LCM, so customer only input LVDS signals to our LCM from their system solution. We provide the Timing Drawing and Timing Formula for customer to how to set their parameters of LCD system, please refer to the LCM SPEC.
4.
4.1
Reference circuit
Interface circuit for AT102TN42
Sandan.Deng
Page 6
5/15/2008
4.2
+3.3v Power
DCLK & LD & STHR & STHL & REV & EDSGL & RGB 18bits & CKV & OEV & STVU & STVD
Signal to panel
Sandan.Deng
Page 7
5/15/2008
5.2
AT102TN42
IR LVDS Connector
12V
DVI
D-sub
S-Video
CVBS
Remote control
Notes: 1. We dont guarantee any power & timing & optical characteristic measure by INL control board. 2. INL control board is just for demo INL digital panel.
Sandan.Deng
Page 8
5/15/2008
Power on/off
Change signal
OSD menu
Sandan.Deng
Page 9
5/15/2008