Академический Документы
Профессиональный Документы
Культура Документы
2008
DD-7
SERVICE NOTES
Issued by RJA
Table of Contents
Cautionary Notes ..............................................................2 Main Specifications ...........................................................3 Location of Controls .........................................................4 Location of Controls Parts List........................................4 Exploded View ..................................................................5 Exploded View Parts List.................................................5 Parts List .............................................................................6 Verifying the Version Number........................................8 Performing a Factory Reset..............................................8 Updating the System ........................................................8 Test Mode ...........................................................................9 Circuit Board (Main Board) ...........................................17 Circuit Diagram (Main Board: Analog) .......................18 Circuit Diagram (Main Board: Digital) ........................20
May. 2008
DD-7
Cautionary Notes
Before beginning the procedure, please read through this document. The matters described may differ according to the model.
No User Data
This product cannot save user data. Backing up user data during servicing is not required.
Parts List
A component whose part code is ******** cannot be supplied as a service part because one of the following reasons applies. Because it is supplied as an assembled part (under a different part code). Because a number of circuit boards are grouped together and supplied as a single circuit board (under a different part code). Because supply is prohibited due to copyright restrictions. Because reissuance is restricted. Because the part is made to order (at current market price).
Circuit Diagram
In the circuit diagram, NIU is an abbreviation for Not in Use, and UnPop is an abbreviation for Unpopulated. They both mean non-mounted components. The circuit board and circuit board diagram show silk-screened indications, but no components are mounted.
May. 2008
DD-7
Main Specifications
DD-7: Digital Delay
Dimensions
73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Input Impedance
1 M
Weight
440 g / 1 lb (including battery)
Accessories
Owners Manual English (#G2507366R0) Mode Sticker (#G2547154R0) Application Sticker (#G2547160R0) Leaflet (USING THE UNIT SAFELY, IMPORTANT NOTES, and Information) (#********) Dry battery/9 V type (6LR61) (#********) * The battery that was supplied with the unit is for temporary use-intended primarily for testing the units operation. We suggest replacing this with an alkaline dry cell.
Output Impedance
1 k
Delay Time
1 ms to 6400 ms * Values may vary according to the mode and connections.
Options
AC adaptor (PSA-series)
Controls
Pedal switch E.LEVEL knob, F.BACK knob, D.TIME knob, MODE knob
* 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Indicator
CHECK indicator (Used for indication of TEMPO, HOLD, and to check battery)
Connectors
INPUT-A (MONO) jack, INPUT-B jack OUTPUT-A (MONO) jack, OUTPUT-B jack TEMPO/EXP jack, AC adaptor jack (DC 9 V)
Power Supply
DC 9 V: Dry battery 6F22 (9 V) type (carbon) Dry battery 6LR61 (9 V) type (alkaline) AC Adaptor (PSA-series: optional)
Current Draw
55 mA (DC 9 V) Expected battery life under continuous use: Carbon: Alkaline: 1.5 hours 6 hours
May. 2008
DD-7
Location of Controls
fig.panel.eps
M3X10 FE ZC
May. 2008
DD-7
Exploded View
fig.bunkai.eps
10 b 11 a
7 6
b d 2 12 1 9
3 4 c
May. 2008
DD-7
Parts List
fig.-part1-e.eps
SAFETY PRECAUTIONS: The parts marked have safety-related characteristics. Use only listed parts for replacement.
Due to one or more of the following reasons, parts with parts code ******** cannot be supplied as service parts. Part supplied only as a component in a complete assembly Copyright does not permit the part to be supplied Part is sold commercially
The description "Q'TY" means a necessary number of the parts per one product.
CASING 22357305R0 22027851R0 75E593C0R0 G2217798R0 75E592T0R0 22357304R0 BOTTOM BASE BOTTOM COVER CASE PANEL PLATE PEDAL PEDAL PLATE 1 1 1 1 1 1
# # #
KNOB, BUTTON # G2477127R0 JACK, EXT TERMINAL 03344701 # F3449150R0 13449140R0 13449717 SWITCH 13129710R0 PWB ASSY #
ROUND KNOB
D-CUT (BLUE/BLACK)
1 2 2 1
SWITCH(PUSH)
JM-0404
75E593P0R1 MAIN SHEET ASSY * This unit includes the following parts. ******** MAIN BOARD ******** VR BOARD ******** INPUT BOARD ******** CTL BOARD ******** LED BOARD
DIODE F5029423R0 RESISTOR # F5399101R0 F5429516R0 MTL.FILM RESISTOR MTL.FILM RESISTOR 0J (1608TYPE) 1R0 J(1608TYPE) 12 12 LED L-3VEGW 1
POTENTIOMETER POTENTIOMETER
3 1
CONNECTOR F3419102R0 WIRING, CABLE # F3487015R0 H4009408R0 # F3477063R0 H4009498R1 # H4009305R0 F3467053R0 # H4009610R0 H4009499R1 H4009597R0 # H4009458R0 # F3467058R1 BATTERY CONNECTOR 006P BATTERY SNAP 1
WIRING WIRING 1007 WIRING WIRING 1P WIRING WIRING 1007-26X3P WIRING WIRING 1P WIRING 1007 WIRING INPUT WIRING
YELLOW 110X6EX6E (EXP) WHITE 85X6X3 RIBBON CABLE 6P X80MM VIOLET L=160MM ORANGE 100X3X6 (OUTPUT) L=65MM CONNECT X 1 GREY 100X3X6 (OUTPUT) GREEN L=160MM BROWN 105X6X3 BLACK 45X6X6 (INPUT) BOARD IN CONNECTOR
1 1 1 1 1 1 1 1 1 1 1
May. 2008
DD-7
SCREWS H5039158R0 40125101 40125134 22137709R0 G2137403R0 H5019413R0 H5029325R0 H5039205R0 H5039510R0 H5039521R0 WASHER M9X14X0.5T THUMB SCREW NYLON WASHER 3X6X0.5 WASHER 9.6X14X1.0 WASHER SCREW M3X10 SCREW 3X6 TOOTH WASHER NUT M9X12X2T NI NUT M7 NI M3X10 FE ZC 5 1 2 1 1 2 5 5 5 4
MISCELLANEOUS H2369451R0 G2537516R0 22177109R0 22267333R0 G2167301R0 22157702R0 22257257R0 ACCESSORIES (Standard) # G6017474R0 # G2507366R0 # G2547154R0 # G2547160R0
LED SPACER PSA CAUTION COIL SPRING CUSHION INSULATING SHEET PEDAL GUIDE BUSH EARTH TERMINAL
1 1 1 1 1 1 2
JAPANESE ENGLISH
1 1 1 1
May. 2008
DD-7
May. 2008
DD-7
Test Mode
Items Required
Oscillator x 2 Oscilloscope x 1 Noise meter x 2 AC adaptor (PSA series device or 9 V DC power source) x 1 Powered monitor x 2 Expression pedal (EV-5) x 1 47-k short plug x 2
Oscilloscope
Noise Meter
Signal Genelator
9V 6.5V
EV-5
2. 3.
Turn down all controls all the way counterclockwise. Holding down the foot pedal and inserting a plug into the INPUT jack makes the CHECK LED light up. * Continue holding down the foot pedal until the LED goes dark. After approximately 2 seconds, the CHECK LED goes dark. * The CPU and DSP checks are performed before the LED goes dark as just described. If a problem is found in the CPU, DSP, or the like, the LED may not go out. After approximately 1 second the CHECK LED flashes, and the number of flashes indicates the version. 1 flash: 2 flashes: flashes: Ver. 1.00 Ver. 1.01 Ver. 1.02
4.
DD-7
Adjust the E.LEVEL control to the 12 oclock position. With the control turned down counterclockwise all the way, turn it clockwise to the 12 oclock position, and verify that the CHECK LED goes dark. At the 12 oclock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
1. VR Check (E.LEVEL)
Make the connections shown below to the INPUT and OUTPUT jacks on the DD-7, using the settings indicated. INPUT A: INPUT B: OUTPUT A: OUTPUT B: 1. Input a rectangular wave at 400 Hz, 800 mVp-p. Input a rectangular wave at 400 Hz, 800 mVp-p. Connect the oscilloscope. Connect the oscilloscope. 5. Turn the E.LEVEL control clockwise all the way. Verify that while the control is being turned all the way clockwise from the 12 oclock position, the CHECK LED stays dark. When the control has been turned clockwise all the way, the LED lights up red.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Verify that the E.LEVEL control is turned down counterclockwise all the way. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
fig.DD-7-wave-1.eps_75
2. VR Check (F.BACK)
Make the connections shown below to the INPUT and OUTPUT jacks on the DD-7, using the settings indicated. 2. With the E.LEVEL control turned down counterclockwise all the way, turn it clockwise to the 9 oclock position. Verify that the CHECK LED goes dark. 3. Turning the control all the way counterclockwise again makes the CHECK LED light up red. 1. INPUT A: INPUT B: OUTPUT A: OUTPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p. Input a rectangular wave at 400 Hz, 800 mVp-p. Connect the oscilloscope. Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Verify that the F.BACK control is turned down counterclockwise all the way. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
fig.DD-7-wave-2.eps_75
10
May. 2008
2. With the F.BACK control turned down counterclockwise all the way, turn it clockwise to the 9 oclock position. Verify that the CHECK LED goes dark. 3. Turning the control all the way counterclockwise again makes the CHECK LED light up red.
fig.DD-7-wave-2.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Verify that the D.TIME control is turned down counterclockwise all the way. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
4.
Adjust the F.BACK control to the 12 oclock position. With the control turned down counterclockwise all the way, turn it clockwise to the 12 oclock position, and verify that the CHECK LED goes dark. At the 12 oclock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
2.
With the D.TIME control turned down counterclockwise all the way, turn it clockwise to the 9 oclock position. Verify that the CHECK LED goes dark. Turning the control all the way counterclockwise again makes the CHECK LED light up red.
3.
fig.DD-7-wave-2.eps_75
5.
Turn the F.BACK control clockwise all the way. Verify that while the control is being turned all the way clockwise from the 12 oclock position, the CHECK LED stays dark. When the control has been turned clockwise all the way, the LED lights up red.
fig.DD-7-wave-1.eps_75
4.
Adjust the D.TIME control to the 12 oclock position. With the control turned down counterclockwise all the way, turn it clockwise to the 12 oclock position, and verify that the CHECK LED goes dark. At the 12 oclock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
11
May. 2008
5. Turn the D.TIME control clockwise all the way. Verify that while the control is being turned all the way clockwise from the 12 oclock position, the CHECK LED stays dark. When the control has been turned clockwise all the way, the LED lights up red. 3. Adjust the MODE knob to the MODULATE position.
DD-7
Verify that waveforms like those shown in the figure below are output. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
fig.DD-7-wave-1.eps_75
4.
Adjust the MODE control to the HOLD position. Verify that waveform output stops. The CHECK LED goes dark.
4. VR Check (MODE)
Make the connections shown below to the INPUT and OUTPUT jacks on the DD-7, using the settings indicated. INPUT A: INPUT B: OUTPUT A: OUTPUT B: 1. Input a rectangular wave at 400 Hz, 800 mVp-p. Input a rectangular wave at 400 Hz, 800 mVp-p. Connect the oscilloscope. Connect the oscilloscope.
fig.DD-7-wave-2.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Verify that the MODE control is at the REVERSE position. Verify that waveforms like those shown in the figure below are output. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
5.
Adjust the MODE control to the 50 ms position. Verify that waveforms like those shown in the figure below are output. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
2.
Adjust the MODE knob to the ANALOG position. Verify that waveform output stops. The CHECK LED goes dark.
fig.DD-7-wave-2.eps_75
12
May. 2008
6. Adjust the MODE control to the 200 ms position. Verify that waveform output stops. The CHECK LED goes dark.
fig.DD-7-wave-2.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Adjust the MODE control to the 800 ms position. Verify that the CHECK LED is lighted up orange. Connect the EV-5 to the TEMPO/EXP jack. Verify that the CHECK LED is lighted up red.
fig.DD-7-wave-1.eps_75
7.
Adjust the MODE control to the 800 ms position. Verify that waveforms like those shown in the figure below are output. The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
3.
fig.DD-7-wave-2.eps_75
8.
Adjust the MODE control to the 3,200 ms position. Verify that waveform output stops. The CHECK LED goes dark.
fig.DD-7-wave-2.eps_75
4.
Depress the toe of the EV-5 pedal, and stop when the intermediate position is reached. Verify that the CHECK LED is lighted up green.
fig.DD-7-wave-3.eps_75
13
May. 2008
5. Depress the toe of the EV-5 pedal all the way. Verify that the CHECK LED is lighted up red.
fig.DD-7-wave-1.eps_75
DD-7
3. Insert the plug into the INPUT B jack. Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75
6.
7. DSP Through Check (INPUT A Check) 6. DSP Through Check (INPUT B Check)
Make the connections shown below to the INPUT and OUTPUT jacks on the DD-7, using the settings indicated. INPUT A: INPUT B: OUTPUT A: OUTPUT B: 1. Input a rectangular wave at 400 Hz, 800 mVp-p. Input a rectangular wave at 400 Hz, 800 mVp-p. Connect the oscilloscope. Connect the oscilloscope. 1. Make the connections shown below to the INPUT and OUTPUT jacks on the DD-7, using the settings indicated. INPUT A: INPUT B: OUTPUT A: OUTPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p. Input a rectangular wave at 400 Hz, 800 mVp-p. Connect the oscilloscope. Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Adjust the MODE control to the 50 ms position. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Adjust the MODE control to the 200 ms position. Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75
2. 2. Disconnect the plug from the INPUT B jack. Verify that the CHECK LED lights up green.
fig.DD-7-wave-4.eps_75
Disconnect the plug from the INPUT A jack. Verify that the CHECK LED lights up red.
fig.DD-7-wave-5.eps_75
If the waveforms grow larger, operation is correct. If the waveforms show no change, operation is faulty.
If the waveforms grow larger, operation is correct. If the waveforms show no change, operation is faulty.
14
May. 2008
3. Insert the plug into the INPUT A jack. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
DD-7
3. Insert the plug into the OUTPUT A jack. Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. Adjust the MODE control to the HOLD position. Verify that the CHECK LED has gone dark.
fig.DD-7-wave-1.eps_75
Set the oscilloscope to 2.0 V/DIV, 1 ms/DIV, and coupling: DC. Adjust the MODE knob to the MODULATE position. Verify that the CHECK LED lights up orange. Verify that the waveforms are not clipped.
fig.DD-7-wave-7.eps_75
2.
Disconnect the plug from the OUTPUT A jack. Verify that the CHECK LED lights up green. 2.
fig.DD-7-wave-6.eps_75
Disconnect the plug from the OUTPUT B jack. Verify that the CHECK LED lights up red.
fig.DD-7-wave-8.eps_75
15
May. 2008
3. Insert the plug into the OUTPUT B jack. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-7.eps_75
DD-7
6. Insert the plug into the OUTPUT B jack. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-7.eps_75
4.
Adjust the MODE knob to the ANALOG position. Verify that the CHECK LED lights up orange. Verify that the waveforms are not clipped.
7.
Adjust the MODE control to the REVERSE position. Verify that the CHECK LED lights up orange. Verify that the waveforms are not clipped.
fig.DD-7-wave-7.eps_75
fig.DD-7-wave-7.eps_75
5.
Disconnect the plug from the OUTPUT B jack. Verify that the CHECK LED lights up red.
fig.DD-7-wave-8.eps_75
Adjust the MODE knob to the ANALOG position. Verify that the CHECK LED goes dark. Verify that residual noise is -93.0 dB or less. Verify that no audible noise or shock noise is present.
2.
Adjust the MODE control to the REVERSE position. Verify that the CHECK LED lights up orange. Verify that residual noise is -99.0 dB or less. Verify that no audible noise or shock noise is present.
3.
Detach the plugs from the INPUT A and INPUT B jacks and switch off the power.
16
May. 2008
DD-7
17
May. 2008
DD-7
INPUT BOARD
PWB F2927058R0 4/6 ASSY 75E593P0R0
MAIN BOARD
BRN 60mm TP65 YEL 70mm TP76 3 2
INPUT A
R57 1M
D6 1SS362FV(TPL3) C6 ; Unpop UnPop AVCC 1 2 1 R61; Unpop R70; 0 Q1 AGND 2SK880-GR(TE85R,F) 3 TP2 R30 C77 10k 1uF TP30 R61 1 TP31 1 C6 10uF 10V 39k IN_REFV 1 AGND R42 AVREF
TP26
INPUT B
BLK 70mm TP77 3 1 2 Q2 2SK880-GR(TE85R,F) D4 AVCC 1SS362FV(TPL3) UnPop 2 1 TP28 GRN 60mm TP73 ORG 70mm TP66 R25 10k AGND C78 1uF
R62 39k C5 10uF 10V R60 39k AVREF 6 5 7 IC4 NJM4558M(TE1) AVCC C34 0.1uF _BYPASS_B C133 68pF
AGND TP79
2
IC4 NJM4558M(TE1)
TP51
R59 1M
R1 10
R43 0
10V 10uF C8
C1 10uF 10V
12k D (0.5%)
R20
C59 47pF TP27 R52 R45 2 C23 22k 22k C15 2200pF D (0.5%) D (0.5%) 10uF 10V 2 1 R82 3 56k D (0.5%) IC1 NJM2115V(TE1) R100 UnPop R51 C21 2200pF D 22k (0.5%) C58 47pF R46 22k D (0.5%) 6 7 5
4 VEE
10(3216) -> 10(3216) -> 10(3216) -> 10(3216) -> 1u -> 10/10
8 VDD
AGND A+3.3
R49 C24 22k 220 D (0.5%) R81 TP60 56k R48 D (0.5%) 22k D (0.5%) 2 2 3 AVREF C18 10uF 10V IC5 NJM4558M DA_A C127 68pF
C9 10uF 10V C31 AGND 0.1uF 2 1 13 14 15 16 7 6 17 12 11 10 9 LIN RIN SDTI LRCK MCLK BCLK DEM1 DEM0 PDN CKS3 CKS2 CKS1 CKS0
C7 100uF 4V
AGND
D+3.3 A+3.3 R24 R39 0 C11 10uF 10V 10k 10k D (0.5%) D (0.5%)
2 C13 10uF 10V _AD_B R80 56k D (0.5%) IC1 <2F5> SD_DA NJM2115V(TE1) LRCK <2E5> A+3.3 <2E5> MCK <2E5> BCK
VD VA
C2 10uF 10V
TP12
AVREF
R50 C22 22k 2200 D (0.5%) TP33 19 R79 LOUT R47 56k D (0.5%) 22k D (0.5%) 6 20 DA_B ROUT 7 8 5 2 IC5 SDTO C14 R92 NJM4 10uF 10V 100 C45 0.1uF AGND A R101 R23 10k 12k D (0.5%)D (0.5%) C27 0.1uF 4 8 VEE VDD AGND TP4 Q6 DTC114TUAT106 3 Q8 DTC114TUAT106 3 R5 56k 1 2 DGND TP1 AVCC
1
C41 0.1uF
8 VDD
R22
5 4
D+3.3
AGND D1 1SS362FV(TPL3) 2 1 TP49 3 R15 1k C130 0.1uF C129 0.1uF C128 0.1uF DGND IN_A_DET IN_B_DET TP19 <2C7> <2C7> Q18 2SC4116-GR(TE85R,F) AGND DGND
VSS
R16 22k
AGND
DGND
4 VEE
AVCC
Battery 006P
R7 56k
1
R11 1k
Q6 ; Unpop -> DTC114TUAT106 R7 ; Unpop -> 56k 1 R58; Unpop -> 1M C67; Unpop -> 0.047uF
1 2
R58 1M
R53 1M
Adaptor PSA-***S
TP6 L3 JK3 D12 WQT-0460 HEC2392-0101509 SS14 1 3 2 2 4 3 1 5 TP74 4 0.1uF 0.1uF C42 C30 D13 GS1G
VBAT
TP61
AVCC TP20
DGND
AGND
AGND
R76 2.2k
3 1
C49 0.1uF
100uF 16V
C57
R93
R38 0
<G10> <G10>
AGND R75
TP35
C66 0.047uF
C67 0.047uF
TP45 Q16 2SC4117-GR(TE85L,F) R31 560 3 1 C73 10uF 10V 2 C54 47uF 10V C40 0.1uF TP7
22k D (0.5%)
LED BOARD
PWB F2927058R0 3/6 ASSY 75E593P0R0
R3 39k
TP3 TP58
2
1 2
R87 270
2 3
D15 UDZS TE-17 9.1B Q17 2SC4116-GR(TE85R,F) TP59 3 Q20 2 2SA1586-GR(TE85R,F) 1 R17 22k R8 22k R98 UnPop
2 1
Q19 2SA1586-GR(TE85R,F)
RIBBONCABLE 3P
3 2
DGND
18
C50 470pF
47k D (0.5%)
R94
R44
R96
R95
May. 2008
DD-7
fig.d-main-analog.eps@R
Q12 2SK879-Y(TE85L,F)
TP21
1
AVREF R35
470k
C17 10uF
R64 1 39k
OUTPUT A
TP81 R85 1k TP69 GRY 100mm BRN 105mm JK5 2 HTJ-064-14D 3 1 SHASSIS
1 D9 1SS387(TPH3,F)
AGND
1 (TE1) TP46
OUTPUT B
WHT 85mm JK6 2 HTJ-064-14D 3 1 SHASSIS
ORG 100mm
0pF TP53
3 D11 1SS387(TPH3,F)
R32 470k
TP10 _DA_B 5 558M(TE1) AVREF AVCC VEE VDD IC5 NJM4558M(TE1) R34 470k C19 10uF R69 39k
2 3
C63
D7 1SS387(TPH3,F)
IC3 NJM4558M(TE1)
D 1 AVCC R2 UnPop TP13 C69 UnPop Q4 DTC114TUAT106 2 3 C65 0.047uF Q5 DTC114TUAT106 2 3 R6 56k TP16 AVCC R4 56k AVCC D5 1SS362FV(TPL3) 2 1 TP29 3 TP15 R9 22k R10 1k D3 1SS362FV(TPL3) 1 2 R12 22k R14 1k TP34 D+1.5 2 R40 0 1 C36 0.1uF R78 56 R77 56 TP50 2 L2 ELL6SH820M TP38 3 C47 0.1uF 5 4 3 TP42 FB_1.5 C25 100uF 4V D+3.3 R41 0 TP47 FB_3.3 C26 100uF 4V <F6> <F6> DGND C39 0.1uF DGND OUT_A_DET OUT_B_DET 3 Q14 QS5U27TR(PB FREE) Q14 QS5U27TR(PB FREE) L1 ELL6SH151M 4 D+3.3
1 2
R54 UnPop
R56 1M
R55 1M
DGND
AGND
DGND
AGND
DGND
C68
0.047uF
Q7 UnPop 3
PVCC
R71
47k
GND
15 16 13 6 5 7 4 19 1 2 3 14 17
FB1 INV1 DTC1 FB2 INV2 DTC2 NON2 STB SEL1 RT CT SCP VREF
VCC
PGND
10
TP63
C48 0.1uF
C72 470pF
20
IC2 BD9851EFV-E2
DGND
DGND
19
May. 2008
DD-7
TP95
TP C87 100uF 4V C121 C91 C109 C101 C112 C119 C104 C103 C107 C114 C110 C98 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
VR BOARD
_DVREF 3
DGND
TP106 DGND
VR2 RD901F-20-15FW-B50K-006 2 F.BACK _DVREF VR3 RD901F-20-15FW-B50K-006 2 D.TIME VR4 RD901F-20-15FW-B50K-08Q7 2 MODE(8click) _DGREF
C88 10uF
1 2 3 4 5 6 CN4
_DGREF
79 80 SCL SDA 102 TP117 103 DCK TP119 D16 104 DMS TP121 1SS362FV(TPL3) 105 DDI TP122 2 1 106 DDO TP118 _DRST ESC+3.3 R103 DVREF TP87 R133 R134 10 84 DGND 4.7k 4.7k 85 AVDD3 TP110 L7 FBMA-10-160808-601T AVREF C90 C115 TP94 100uF 4V 0.1uF 95 AGND3 TP113 L8 FBMA-10-160808-601T 94 AVREF R132 R135 R107 DVREF C85 93 0 4.7k 92 AIN7 10uF 10V 4.7k DGREF DGND 1 91 AIN6 2 90 AIN5 3 89 AIN4 88 AIN3 4 87 AIN2 5 86 AIN1 6 AIN0 TP100 R102 RIBBON CABLE 6P CN3 10 134 R110 0 DGREF AVDD1 R106 0 C89 C111 100uF 4V 0.1uF R111 0 133 R108 0 AGND1 TP97 139 XIN D+3.3 C125 DGREF PVCC 22pF 140 X1 XOUT DGND C126 ESB16.9344F16D35F 98 22pF R131 99 TMODE 1 IC11 135 TMODE 0 R109 BD45431G-TR R131; 18K (MF) -> 15K (MF) 136 TMC1 0 4 137 TMC2 5 VDD VOUT 142 _TRST 1 143 SMC 3 C123 2 R124 ER AMC GND UnPop UnPop R131; 15K (MF) -> 0 DGND 81 _RESE R124; 33K (MF) -> UnPop IC11; BD45301G-TR -> BD45431G-TR 70 SW_PDL TP85 DGND RESET <C9> 71 TXD1/ <B3> 74 RXD1/ TP123 DGND 75 TXD0/ TP120 RXD0/ 76 WP_USER <B5> 77 TI/P7 TCLR/ BYPASS_A_MUTE 119 <1E5> PWM/S BYPASS_B_MUTE 118 _SYNC 1 8 <1F5> 2 7 110 <1D5> MCK 3 6 111 MCK/T <1D5> BCK 4 5 107 BCK/T LRCK <1D5> LRCK/ RA8 112 SD_DA <1D5> SD_AD 113 SD7/T 100 <1D6> 116 SD6/T 117 SD5/T <1F5> BYPS_A_TO_B_MUTE SD4/T R105 470k R136 4.7k 3 TP103 TP104 0.01uF 0.01uF 0.01uF 0.01uF TP98 TP101 TP89 TP88 C124 1000pF C93 0.1uF DGND ESC+1.5 C82 C80 C83 C81 R104 56k 0.1uF C12 2 SUB TP108 TP90 TP92 TP105 TP107 TP84 1 2
20
C116 0.1uF
IC10 TC7W04FK(TE85L/F)
3 2 1 5 6 7
TP102
3 2 1 5 6 7
<E5>
May. 2008
DD-7
fig.d-main-digital.eps@R
D+3.3 L6 FBMA-10-160808-601T
D+1.5 L5 FBMA-10-160808-601T
ESC+3.3 86
ESC+1.5 TP91 C86 100uF 4V C113 C117 C118 C94 C100 C108 C96 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF DGND
9 17 26 34 49 61 82 96 114 122 132 144 EVDD EVDD EVDD EVDD EVDD EVDD EVDD EVDD EVDD EVDD EVDD EVDD
0.01uF C79
3 P 3 M
5 5
1 0
T P61 P60 P76 P75 4 BUDO0/P73 D2/TRR2/P82 /SD3/TRR3/P83 RCKI/P71 RCKO/P70 _SYNC/P72 RR7/P87 RR6/P86 RR5/P85 RR4/P84
121 _CS4/SD0/TRR0/P80 68 _CS3/P63 69 _CS1/SPICS/P62 124 A23/_SYNC/TRS7/P97 125 A22/TRS6/P96 126 A21/TRS5/P95 127 A20/TRS4/P94 128 A19/TRS3/P93 129 A18/TRS2/P92 130 A17/TRS1/P91 131 A16/TRS0/P90 53 AD15/PWM/P57 54 AD14/SPICK/P56 56 AD13/SPIDI/P55 57 AD12/SPIDO/P54 58 AD11/BUCK/P53 59 AD10/BULCK/P52 60 AD9/BUDO1/P51 63 AD8/P50 43 AD7/P47 44 AD6/P46 45 AD5/P45 46 AD4/P44 47 AD3/P43 48 AD2/P42 51 AD1/P41 52 AD0/P40 64 ALE/P67 65 _CRD/P66 66 _CWR/P65 67 _WAIT/P64 120 INT2/SD1/TRR1/P81 78 INT1 22 EA13/_CRD/P10 24 EA12/_WAIT/P22 21 EA11/ALE/P11 28 EA10/_CS1/P20 23 EA9/_CWR/P23 25 EA8/_CS3/P21 29 EA7/AD15/P37 31 EA6/AD13/P35 33 EA5/AD11/P33 39 EA4/AD9/P31 40 EA3/AD8/P30 38 EA2/AD10/P32 32 EA1/AD12/P34 30 EA0/AD14/P36 2 ED7/P07 3 ED6/P06 4 ED5/P05 5 ED4/INT2/P04 6 ED3/_CS6/P03 7 ED2/_CS4/P02 8 ED1/A23/P01 11 ED0/A22/P00 20 _ECS/A16/P12 19 _ERAS/A17/P13 16 _ECAS/A18/P14 14 _EWE/A19/P15 13 EUDQM/A20/P16 12 ELDQM/A21/P17 15 ECK IGND IGND IGND IGND IGND IGND 37 42 73 100 109 138
For UPDATE
DA_B_MUTE <1F5> ESC+3.3 CN5 1 UnPop 2 3 4 5 6
R126 100k
<B5> SDA <B5> SCL <1E4> <1E4> <B5> WP_PROG <1E8> <1E8> DGND <1H5> <1D5> <1H5> ESC+3.3 R112 10k
SW BOARD
ESC+3.3
PWB F2927058R0 6/6 ASSY 75E593P0R0
<E5>
SW_PDL R125 1k
TP111
R118 10k
TP114
1
TP111,TP114
DGND
DA_A_MUTE <1E5> 4 3 2 1 EA(7) EA(6) EA(5) EA(4) EA(3) EA(2) EA(1) EA(0) 4 3 2 1 4 3 2 1 4 RA1 3 47 2 1 4 RA2 3 47 2 1 1 2 RA7 3 47 4
DGND 5 6 RA3 7 47 8 5 6 RA4 7 47 8 5 6 RA6 47 7 8 S_ED(7) 5 S_ED(6) 6 S_ED(5) 7 S_ED(4) 8 S_ED(3) 5 S_ED(2) 6 S_ED(1) 7 S_ED(0) 8 8 7 6 5 R138 47 8 7 6 5 S_EA(9) S_EA(12) S_EA(8) S_EA(10) S_EA(12) S_EA(13) S_EA(7) S_EA(11) S_EA(0) S_EA(10) S_EA(6) S_EA(9) S_EA(1) S_EA(8) S_EA(7) S_EA(5) S_EA(6) S_EA(2) S_EA(5) S_EA(4) S_EA(4) S_EA(3) S_EA(3) S_EA(2) S_EA(1) S_EA(0) S_EA(0:13)
S_ED(0:7)
C106 0.1uF
C99 0.1uF
C102 0.1uF
C120 0.1uF
C92 0.1uF
C97 0.1uF
C95 0.1uF
19 18 17 16 39 15 38 37 40
EGND EGND EGND EGND EGND EGND EGND EGND EGND EGND EGND
1 2 RA5 3 47 4
1 10 18 27 35 50 62 83 97 115 123
IC7 UPD800402GJ-211-UEN-A(ESC)
DGND
Connect to SHASSIS
27 _CS VDD 14 _RAS VDD 1 _CAS VDD 49 _WE VDDQ 43 UDQM VDDQ 9 LDQM VDDQ 3 CLK VDDQ CKE NC/RFU 52 VSSQ 46 VSSQ 12 VSSQ 6 VSSQ 54 VSS 41 VSS 28 VSS IC9 K4S641632K-UC75000 1 C132 TER3 UnPop UnPop 1 C131 TER4 UnPop UnPop DGND
SD+3.3 DGND
20 21 36 35 22 34 33 32 31 30 29 26 25 24 23
DQ15 BA0 DQ14 DQ13 BA1 DQ12 NC DQ11 A11 A10/AP DQ10 DQ9 A9 DQ8 A8 DQ7 A7 DQ6 A6 A5 DQ5 DQ4 A4 DQ3 A3 DQ2 A2 DQ1 A1 DQ0 A0
53 51 50 48 47 45 44 42 13 11 10 8 7 5 4 2
S_ED(7) S_ED(6) S_ED(5) S_ED(4) S_ED(3) S_ED(2) S_ED(1) S_ED(0) S_ED(0) S_ED(1) S_ED(2) S_ED(3) S_ED(4) S_ED(5) S_ED(6) S_ED(7)
D+3.3
L4 FBMA-10-160808-601T TP93
C84 100uF 4V
21
May. 2008
DD-7
22
May. 2008
DD-7
23
May. 2008
DD-7
MEMO