MAY.10,1982
VB-2
OBOSS vB-2
SPECIFICATIONS
Power seeeeeees OV, 11mA DC
Maximum input level .... —5dBm (@ 1kHz)
Input impedance ,...... —2dBm (@ 100Hz)
Output load impedance .. 10k or more
Frequency response
Delay time . ms (@ DEPTH min.)
LFO rate 2Hz-15Hz z
Rise time . 150ms-5s saan 1G
SIN ratio . —92¢8 (IHF-A) em
Dimensions . ++ 7O(W) x 55(H) x 125(D)mm (2-3/4" x 2-1/4" x 5")
Weight ...........+.++ 4509 (1 Ibs)
soek HEC0749-01.010 (13489704)
40Hz-17kHz (LATCH,UNLATCH)
RVICE NOT
First Edition
ave (2217010300),
Guide bushing
(216070200)
‘case (2201015101)
BATTERY.
STRAP ~: Cover (2202011600)
\. ase (2235030500)
LED sLP.1388 (18020117),
= 1 swiven sru1023 113119208)
Pot, K121B000ME-260KC (13279709): oe
Panel (2221028700)
Knob (2247012700)
Pot, K1218000ME:SOKB (19279707)
Jock 56.7615 (15440105)
Pedal (2218052300)
Pot, K121BO00ME-50KE (12279708)
Jock 86-7713¢4 (13440104)
Base (2236090400)
Decoration serew @ x 10mm
PARTS LIST
2201015101 Case blue
2218052300 Pedal blue
2202011600 Cover bottom (065-130)
2235030400 Base pedal matt (111-031)
2235030500 Base bottom (111-032)
2215070201 Guide bushing (068-026)
2247012700 Knob (016-077)
2221028700 Panel
2216050200 Spacer pob-rear cover (085-153)
2226030500 Cushion ppeb-rear cover, battery-pedal (107-053)
2217010800 Coil spring (070-059)
JACK
13449704 HEC-0749-01.010 AC adaptor ey
19449104 $G-771344 (009-036) 13129710 JM-0404 (001-295)
13449105 $G-7615 (009-001) 13119208 SRU1023_ rotary
Roland Printed in Japan BB-2 1PcB
7522151003 Assy ET5221-510 (pcb 2291053401)
2291053401 LED mounting PCB only
POTENTIOMETER
13279707 K121BOOOME-50kB DEPTH
13279708 K121BOOOME-250kA RISE TIME
13279709 K121BOOOME-250kC RATE
13299114 H1051A013-10kB —_ trimmer (030-465)
13299122 H1051A023-470kB _ trimmer (030-475)
SEMICONDUCTOR
15219211 MIN3207 IC BBD 1024-Stage Low Voltage Operation
15219210 MN3102 IC BBD Driver
15189102 NUM4558DD_ IC" (020-071)
15189115 TLO22CP Ic (020-164)
15229802 BA662A Ic
15229809 BAG34 Ic
15129108 2SC945.P Tr. (017-110)
15129104 2SC732TM-GR Tr. (017-104)
15119105 2SA733-P Tr. (017-024)
15019523 RDS.1EB-3 zener (018-075)
15019633 RD11FB-3 zener
15019125 ‘185-133 diode
15029117 SLP-135B LED (019-034)
2343095800 Flat cable
ADJUSTMENT
1. BBD DRIVE CLOCK
CONTROL : MODE — BYPASS
TEST POINT : Pin 4 of IC3
Adjust VR4 for 8.3us/cycle (120kHz)
2. BBD BIAS
CONTROL: MODE — UNLATCH
TEST POINT : OUTPUT jack
TEST SIGNAL : dBm, 200Hz, sine into INPUT jack
Set VRS ot the point about which output swings symmetrically with
minimum distortion,VB-2
CHECK (check point - OUTPUT jack) RISE TIME
BYPASS
MODE: BYPASS DEPTH: FCCW ee
1. Verify near perfect rectangular and unlit i
LATCH TEST SIGNAL: 200mVp-p, 200Hz
1. Check the time required for |
reach full sweep with RISE TIME
a) No delay at FCCW
b) Approximately 3 sec at FCW
MODE: LATCH — slight tilt (sag) and overshoot on wave top
DEPTH: FCW
1. Stepping the pedal several times, confirm:
a) Indicator repeats ‘‘on’’ and “off”,
'b) Pedal switchings have no effect on waveform shape. BA634
UNLATCH
Relerence voltage
MODE: UNLATCH — waveform remains the same as in LATCH MODE
DEPTH: FCCW
1, Step the pedal on and check:
a) Indicator lights and goes off as the pedal released,
RATE
MODE: LATCH DEPTH: Midpoint
1. Check the sweep rate at the extremities of RATE setting:
2 cycles at FCCW; 15 cycles at FCW.
Re 87
eB
ac 4
ADAPTOR