Академический Документы
Профессиональный Документы
Культура Документы
Introduction
The purpose of this document is to help service workshop technicians to service products. This service manual must be used only by authorized service suppliers. The content of it is confidential. Please note that provides other guidance documents for service suppliers. Follow these regularly and comply with the given instructions. While every effort has been made to ensure the accuracy of this document, some errors may exist. Please keep in mind also that this documentation is continuously being updated and modified, so always watch out for the newest version.
CAUTIONS
1 Please read this service manual carefully and make sure all elements of anti-static are in place before the repair work is carried out. 2 Servicing and alignment MUST be undertaken by qualified personnel only. 3 Please use specified tools and equipments for servicing, in which the parameters need to be calibrated with specified criteria.
Content
Chapter 1 Product Specification..3 Chapter 2 Explosive View...4 Chapter 3 Tools....5 Chapter 4 Guidance of Disassembly/Assembly.......................................................................................68 Chapter 5 Pictures of PCBA.910 Chapter 6 System block diagram......11 Chapter 7 Circuit diagram for each unit.......1218 Chapter 8 Troubleshooting Guide....1924 Chapter 9 Guidance of Firmware Upgrading & Write IMEI...............2533 Chapter 10 CIT Testing....34
Main features and functions Dual SIM Dual Standby Single Connection FM Radio Multi-Media USB 1.1 data transfer T-FlashSupport 8G T Card 1.8TFT QQVGA MP3/ AVI
Specification Network: GSM/GPRS 900/1800 or 850/1900MHz Display: 1.8TFT QQVGA RadioFM radio FM Record to T-Flash Talking time:570Min Standby time:289H Lithium Battery: Standard1000mAh USB ChargingUSB 1.1 The actual time shall vary depending on the network situation
Chapter 3 Tools
lron
850 heater
Solder wire
Soldering paste
Voltage regulator
Multi-meter
tweezers Software
Screw
Wrist strap
Writ strap
tweezersscrewdriverpickwrist strap
4.1 Disassembly
4.2 Assembly
LCD Connector
Keypad connector A
5.1.2 Instruction & location of main components on side B. U101 CPU MT6252
U502 PA RF7170
U301 Flash IC
10
11
Audio process
JAVA Process
O/I Interface
BT Module
12
13
SIM 2 Clock
SIM 2 Data
SIM 2 Reset
14
item Vcore Vio Vadd Vtcxo Vrtc Vmem Vsim Vcs vcs
voitage 1.2v 2.8v 2.8v 2.8v 1.2v 2.8v 2.8v 2.8v 1.8v
current 200ma 100ma 150ma 20ma 200ma 150ma 20ma 200ma 150ma
Positive Supply
Voltage
15
Data Transfer
16
Power Supply
Antenna
RF Signal Input
RF7170
7.5 FM Radio Modules The AR1216 processes the FM broadcasting signal that received from antenna (FM/ANT) ,produces and sends audio signals (FM-INL, FM-INMR) to the audio process module of CPU for decoding, where the electrical signals of audio are made.
17
SIM 1Clock
SIM 2 Data
18
Cannot download
Can on?
power
YES
YES
OK
YES
Check if I/O connector is false weld or damaged NO Plug the cable and check if the current is high(normally 30mA NO Check if CPU has power output and open circuit NO
Change or reconfigure
YES
Replace U101
19
NO
YES
NO
OK
YES
Change SIM
Is SIM invalid?
Problem Solved
YES
NO
YES
MT6252 is broken
20
Cannot Power On
Cannot Power On
NO
YES
NO
YES
Try to power on when connect to the power regulator NO Check if the current is around 3040MA
Problem Solved
YES
Firmware upgrading
NO
NO
YES
MT6252 is broken
21
NO
Check if broken.
LS401
is
YES
NO
YES
Change receiver
YES
NO Test receiver by using power supply, if there is sound of YES Test if LS401 with Oscillograph when on the call. NO NO Change receiver.
NO
22
No Incoming Ring
No incoming ring
NO
Remove receiver and test with power supply to see if there YES NO
YES
Cancel mute.
YES
Change speaker
NO
NO Test the LS401 when ringing is on by using oscillograph. NO Change U101 or U401
23
Display Problem
Display problem
LCD
NO
Change LCD
YES
NO Check if the pin13 of J705 has signal and the connector is normal. NO YES Firmware upgrading
24
Please keep the USB cables unplugged when installing the driver. Plug the USB cable when installing is completed. And check device manager of the PC.
9.1.3 Please select Options-COM port-Choose the port which is same as the one in Device Manager
25
9.1.4 Select Options-Format FAT (DISABLED) and please do NOT select validation.
26
Double click
Double click.
27
Double click
9.1.8. Click ROM and select X11-23_PCB00_gprs_MT6226_S01. Bin file. Note: Please use the latest version.
28
9.1.9 Power off the handset, remove the battery, click Download, and connect the cable with handset, then insert the battery, press the power on button, the red and blue progress bar shall appear.
29
30
Figure 1-1 For the first time you run IMEI_Writer in the computer, figure 1-2 occurs. Choose the right database file for the slave phone of MGSM 41B phone referring to figure 1-3.
Figure 1-2
Figure 1-3
31
1.2 input the IMEI of the slave phone referring to figure 1-4, click Restart, after 3 seconds plug the slave phone cable connector to the phone and power on the phone.
IMEI
Figure 1-4 1.3 after several seconds, figure 1-5 occurs to show the slave phone is written to the phone successfully.
Figure 1-5
2. Write the IMEI of the master phone. If necessary, you can also use IMEI_Writer to write IMEI to the master phone conveniently.
32
2.1 Change the database file to be for the master phone, referring figure 1-4. 2.2 Input the IMEI of the master phone, click Restart, after 3 seconds plug the master phone cable connector to the phone and power on the phone. 2.3 after several seconds figure 1-5 occurs to show the slave phone is written to the phone successfully.
3 write the IMEI of another phone If the right database file has already been chose, click the restart, input the IMEI of the phone, click Restart, after 3 seconds plug the phone cable connector to the phone and power on the phone. After several seconds, figure 1-5 occurs to show the slave phone is written to the phone successfully.
33
34