Академический Документы
Профессиональный Документы
Культура Документы
APPROVED BY
CHECKED BY
ORGANIZED BY
RECORD
Revision Date 1999/10/6 Page -
OF
REVISION
Contents New Release
FEATURES
(1) Display format : 8 characters 2 lines (2) Construction : STN LCD panel, Bezel, Zebra and PCB. (3) Optional LED back-light. (4) Controller : SED1278 or Equivalent. (5) 5V single power input. (Special request for 3.3V driving, built-in DC/DC converter.) (6) Normal / Extended temperature type.
MECHANICAL DATA
Parameter Dot size Dot pitch Character size Viewing area Module size Module size (w/ LED back-light) Stand Value 0.545(W) 0.645(H) 0.60(W) 0.70(H) 2.945(W) 5.545(H) 35.0(W) 15.0(H) 58.0(W) 32.0(H) 10.0 max (T) 58.0(W) 32.0(H) 13.8 max (T) Unit mm mm mm mm mm mm
ELECTRO-OPTICAL CHARACTERISTICS
Parameter Logic Circuit Supply Voltage LCD Driving Voltage Symbol VDD-VSS VDD-VO Condition --20 C 0 C 25 C 50 C 70 C Input Voltage Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range VIH VIL IDD --VDD = 5V Min 2.7 4.5 4.45 4.4 4.2 4.0 0.7 VDD VSS -Typ -4.7 4.65 4.6 4.4 4.2 --1.0 Max 5.5 4.9 4.75 4.8 4.6 4.4 VDD 0.3 VDD 1.5 V V mA Unit V V 0 ~ 50 C for Normal Temp. type -20 ~ 70 C for Extended Temp. type Note
----- Optical Characteristics ----CR tr tf f b l r Frame Frequency Forward Voltage Forward Current fF VF IF 25C -VF=4.05V VF=4.05V 25C 25C 25C 25C & CR2 ------------A
Bare LED Luminous intensity VF=4.05V LCM Luminous intensity * LED Dice number = 27=14
(NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state) ( NOTE 2 ) Response time :
E RS R/W DB0~DB7
COM 1-16
SED1278
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Symbol VSS VDD VO RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 Ground (0V)
Function Supply Voltage for Logic (+5V or +3.3V) Contrast Adjustment Data/Instruction Select Read/Write Select Enable Signal Data Bus Data Bus Data Bus Data Bus Data Bus Data Bus Data Bus Data Bus
POWER SUPPLY
LCD Module
VDD(+5V) VDD(+3.3V) LCD Bias Circuit
R1 VR
LCD Module
R2 VSS
5V Power Input
LED_BACKLIGHT
JP3
There are two methods to light up the LED back-light : (Please indicate while ordering.) (1) Add +4.05V between LED A & K directly. (Default) (2) Short JP1&JP3 and use current-limit resistor(R9/R10), use the same power (+5V) with the logic circuit.
TIMING CHARACTERISTICS
Write Operation
Item
Symbol
Unit
Enable cycle time Enable pulse width Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data set-up time Data hold time
ns
Read Operation
Item
Symbol
Unit
Enable cycle time Enable pulse width Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data delay time Data hold time
ns
10
INSTRUCTION SET
RS R/ W 0 0 0 0 Code D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 Description E.T.(fOSC =270 KHZ) 1.53 ms 1.53 ms
Instruction
Entry Mode SET Display ON/OFF Control Cursor or Display Shift Function Set
0 0
0 0
0 0
0 0
0 0
0 0
0 1
1 Write20H to DDRAM and set DDRAM address to 00H from AC 0 1 -- Sets DD RAM address to 00H from AC and return cursor to its original position if shifted. The contents of DDRAM are not changed. 1 I/D SH Assign cursor moving direction and enable the shift of entire display. D C B Set display (D), cursor (C), and blink of cursor (B) on/off control bit. --
39 S 39 S 39 S 39 S
Set CG RAM Address Set DD RAM Address Read Busy Flag and Address Write Data to RAM Read Data from RAM
-- Set cursor moving and display shift control bit, and the direction, without changing of DDRAM data. 0 1 DL N F -- -- Sets interface data length (DL:8-bit/4-bit), number of display lines (N:2-line/1-line) and , display font type (F:5x11dots/5x8 dost). 1 AC AC AC AC AC AC Sets CG RAM address in address counter. 5 4 3 2 1 0
1 S/ R/ C L
39 S 39 S 0 S 43 S 43 S
1 AC AC AC AC AC AC AC Sets DD RAM address in address counter. 6 5 4 3 2 1 0 BF AC AC AC AC AC AC AC Whether during internal operation or not 6 5 4 3 2 1 0 can be known by reading BF. The contents of address counter can also be read. D7 D6 D5 D4 D3 D2 D1 D0 Writes data into internal RAM (DD RAM /CG RAM). D7 D6 D5 D4 D3 D2 D1 D0 Reads data from internal RAM (DD RAM /CG RAM).
1 1
0 1
* -- : dont care Note : When an MPU program with checking the Busy Flag(DB7) is made, it must be necesssary1/2Fosc is necessary for executing the next instruction by the falling edge of the E signal after the Busy Flag(DB7) goes to LOW.
11
10 INITIALIZATION SEQUENCE
11 DD RAM ADDRESS
DIGIT 1 LINE 2 LINE 1 2 3 4 5 6 7 8 Display Position DD RAM Address
00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47
12
12 FONT TABLE
0 CG 0 RAM (1) CG 1 RAM (2) CG 2 RAM (3) CG 3 RAM (4) CG 4 RAM (5)
Lower 4-bit (D0 to D3) of Character Code (Hexadecimal)
CG 5 RAM (6) CG 6 RAM (7) CG 7 RAM (8) CG 8 RAM (1) CG 9 RAM (2) CG A RAM (3) CG B RAM (4) CG C RAM (5) CG D RAM (6) CG E RAM (7) CG F RAM (8)
* Character codes (00H-0FH) of SED1278F are assigned to the area of character generator RAM (CG RAM). The CG ROM of the SED1278F is masked; if you wish to have your own CG ROM, consult S-MOS Marketing Department for conversion of the masked ROM.
13
A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation.
13.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits.
14
Black lines
Minor
2.5
Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle
15
13.6 RELIABILITY
Test Conditions Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Thermal Shock Test Normal Temp. type 503C , t=96 hrs 03C , t=96 hrs 703C , t=96 hrs Extended Temp. type 703C , t=96 hrs -203C , t=96 hrs 803C , t=96 hrs 1,2 Note
1,2 -203C , t=96 hrs -303C , t=96 hrs -30C ~ 25C ~ 80C -20C ~ 25C ~ 70C 5 min. 30 min. 30 m in. 5 min. 30 min. 30 min. 1,2 ( 1 cycle ) ( 1 cycle ) Total 5 cycle Total 5 cycle 40 C, Humidity 90%, 96 hrs 1,2
Humidity Test
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35C , 45-65%RH). Definitions of life end point : l Current drain should be smaller than the specific value. l Function of the module should be maintained. l Appearance and display quality should not have degraded noticeably. l Contrast ratio should be greater than 50% of the initial value.
16
14 HANDLING PRECAUTIONS
(1) An LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in colour. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions.
17
15 OUTLINE DIMENSION
18