Академический Документы
Профессиональный Документы
Культура Документы
1W, FIXED INPUT ISOLATED & REGULATED SINGLE OUTPUT MINIATURE SIP/DIP PACKAGE
RoHS FEATURES
SIP/DIP Package 3KVDC Isolation Temperature Range: -40C to +85C Industry Standard Pinout No Heat sink Required No External Component Required PCB Mounting RoHS Compliance Short Circuit Protection
PRODUCT PROGRAM
Input Part Number IF0505S-W75 IF0505S-1W IF0509S-1W IF0512S-1W IF0515S-1W IF0505D-W75 IF0505D-1W 5 4.75-5.25 Voltage (VDC) Nominal Range Voltage (VDC) 5 5 9 12 15 5 5 9 12 15 5 5 9 12 12 11.4-12.6 15 5 5 9 12 15 5 5 9 12 24 22.8-25.2 15 5 5 9 12 15 Output Current (mA) Max 150 200 111 83 67 150 200 111 83 67 150 200 111 83 67 150 200 111 83 67 150 200 111 83 67 150 200 111 83 67 Min 15 20 12 9 7 15 20 12 9 7 15 20 12 9 7 15 20 12 9 7 15 20 12 9 7 15 20 12 9 7 68 66 70 72 73 68 66 70 72 73 68 67 71 73 74 68 67 71 73 74 68 67 72 73 74 68 67 72 73 74 SIP SIP SIP SIP SIP DIP DIP DIP DIP DIP SIP SIP SIP SIP SIP DIP DIP DIP DIP DIP SIP SIP SIP SIP SIP DIP DIP DIP DIP DIP Efficiency Package (%, Typ) Style
APPLICATIONS
The IF_S(D)-1W Series are specially designed for applications where a single power supply is highly isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation 5%); 2) Where isolation is necessary between input and output (isolation voltage 3000VDC); 3) Where the regulation of the output voltage and the output ripple and noise are demanding.
IF0509D-1W IF0512D-1W IF0515D-1W IF1205S-W75 IF1205S-1W IF1209S-1W* IF1212S-1W IF1215S -1W IF1205D-W75 IF1205D-1W IF1209D-1W* IF1212D-1W IF1215D-1W IF2405S-W75 IF2405S-1W
MODEL SELECTION
Rated Power Package Style Output Voltage Input Voltage Product Series
ISOLATION SPECIFICATIONS
Item Isolation voltage Isolation resistance Test condition Tested for 1 minute Test at 500VDC Min 3000 1000 Typ Max Units VDC M
The copyright and authority for the interpretation of the products are reserved by MORNSUN
OUTPUT SPECIFICATIONS
Item Output power Line regulation Load regulation Output voltage accuracy Temperature drift Output ripple* Output noise* Switching frequency For Vin change of 5% 10% to 100% full load 100% full load 100% full load 20MHz bandwidth 20MHz bandwidth Full load, nominal input voltage 10 50 100 Test condition Min 0.1 Typ Max 1 0.25 1 3 0.03 20 100 KHz %/C mVp-p % Units W
TYPICAL CHARECTERISTICS
Temperature Derating Graph
*Test ripple and noise by parallel cable method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Operating Temp.( C )
COMMON SPECIFICATIONS
Item Storage humidity range No-load power consumption Storage humidity range Operating temp. range Temp. rise at full load Lead temperature Short circuit protection Cooling Case material MTBF 3500 1.5mm from case for 10 seconds IFXX05S/D-1W* Others -55 -40 15 10 125 85 25 300 1 Continuous Free air convection Plastic (UL94-V0) K hours S C Test condition Min Typ Max 95 Units %
APPLICATION NOTE
Requirement On Output Load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load could not be less than 10% of the full load. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our companys products with a lower rated output power (IF_S(D) W25 Series).
RECOMMENDED CIRCUIT
L L
Vin
C
+Vo
DC DC
(Figure 1)
GND
0V
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must proper. If the capacitance is too big, a startup problem might arise. For every channel of output, providing the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor refer to (Table 1). To get an extremely low ripple, an LC filtering network may be connected to the input and output ends of the DC/DC converter, which may produce a more significant filtering effect. It should also be noted that the inductance and the frequency of the LC filtering network should be staggered with the DC/DC frequency to avoid mutual interference (Figure 1).
Vin (VDC) 5 12 24 -
Vout (VDC) 5 9 12 15
Its not recommended to connect any external capacitor in the application field with less than 0.5 watt output.
Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against over-current .The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit.
When the environment temperature is higher than 71C, the product output power
should be less then 60% of the rated power.
0.50[0.020]
19.60[0.772]
(Front View)
10.00 [0.394]
4.10[0.161]
2.18[0.086] 2.54[0.100]
19.60[0.772]
Note: Grid:2.54*2.54mm.
Note: Unit:mm[inch] Pin section tolerances:0.10mm[0.004inch] General tolerances:0.25mm[0.010inch] FOOTPRINT DETAILS Pin 1 2 4 6 Function Vin GND 0V +Vo
Note: 4.70[0.185] Unit :mm[inch] General tolerances: 0.50mm[0.020inch] L=530mm[20.866inch] Devices per tube quantity: 25pcs L=220mm[8.661inch] Devices per tube quantity: 10pcs Short tube inner packaging dimensions: L*W*H=255*170*80mm Short tube outer packaging dimensions: L*W*H=375*280*270mm Long tube inner packaging dimensions: L*W*H=580*200*100mm Long tube outer packaging dimensions(with two inner packaging boxes): L*W*H=600*215*220mm Long tube outer packaging dimensions(with three inner packaging boxes): L*W*H=600*215*325mm
MECHANICAL DIMENSIONS
IF_D-1W Series DIP package
RECOMMENDED FOOTPRINT
0. 50[0.020]
Front View
7.00 [0.276]
14
4.10[0 .161]
16.70 [0.657]
0.50[0.020]
11
9 7
0.30[0.012]
0.50[0.020]
Note: Unit:m m[inch] Pin section tolerances:0.10mm [0.004inch] General tolerances:0.25m m[0.010inch]
FOOTPRINT DETAILS Pin 1 7 9 11 14 Function GND NC +Vo 0V Vin
NC: No connection
Note: 5.30[0.209] Unit :mm[inch] General tolerances: 0.50mm[0.020inch] L=530mm[20.866inch] Devices per tube quantity: 25pcs L=220mm[8.661inch] Devices per tube quantity: 10pcs Short tube inner packaging dimensions: L*W*H=255*170*80mm Short tube outer packaging dimensions: L*W*H=375*280*270mm Long tube inner packaging dimensions: L*W*H=580*200*100mm Long tube outer packaging dimensions(with two inner packaging boxes): L*W*H=600*215*220mm Long tube outer packaging dimensions(with three inner packaging boxes): L*W*H=600*215*325mm
Note: 1. All specifications measured at TA=25C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. See below recommended circuits for more details. 3. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life of product.
The copyright and authority for the interpretation of the products are reserved by MORNSUN