PART 5
Specifications and Codes
Page Nos.
CROSS-REFERENCE TO THE 1978 AISC SPECIFICATION ........ 52 -5-9
SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS—
ALLOWABLE STRESS DESIGN AND PLASTIC DESIGN ......... S11 ~ 5-220
Specification . 5:24 ~ 5.97
Appendix : 5-98 — 5-116
Numerical Values 5-117 — 5-122
- 5-123 ~ 5-220
-223 — 5-261
Commentary .
AISC CODE OF STANDARD PRACTICE
SPECIFICATION FOR STRUCTURAL JOINTS
USING ASTM A325 OR A490 BOLTS.............-...0.500008 5-263 - 5-307
SPECIFICATION FOR ALLOWABLE STRESS DESIGN
OF SINGLE-ANGLE MEMBERS.....
AISC QUALITY CERTIFICATION PROGRAM ......
5-309 — 5-323
5-325 — 5-329
Awarrican Instrruns oF Steet Consraucrion5-2
Cross Reference to the 1978 AISC Specification for the Design, Fabrication and
Erection of Structural Steel for Bulidings
This table provides a cross-reference of the 1989 Specification for Structural Steel
Buildings—Allowable Stress Design and Plastic Design alphanumeric section desig-
nations and their headings, to the 1978 Specification section numbers. A “—” indi-
cates there was no specific section in the 1978 Specification corresponding to that
1989 Specification section.
1989 Spec. 1978 Spec.
Chapter A GENERAL PROVISIONS
AL Scope
A2 Limits of Applicability
AL Structural Steel Defined —
A22 ‘Types of Construction 1.2
A3 Material 1.4
A3L Structural Steel
A3.1a ASTM designations 14.1.1
A3.1b Unidentified steel 1.4.1.2
A3.1c Heavy shapes new
A32 Steel Castings and Forgings 1.4.2, 1.5.4
A33 Rivets 1.4.3
A34 Bolts, Washers and Nuts 144
A3.5 Anchor Bolts and Threaded Rods ~
A3.6 Filler Metal and Flux for Welding 1.4.5
A3.7 Stud Shear Connectors 1.4.6
Ad Loads and Forces 1.3.7
A4.1 Dead Load and Live Load 13.12
A42 Impact 13.3
A43 Crane Runway Horizontal Forces 1.3.4
AG Wind 13.5
A4S Other Forces 13.6
AS Design Basis
AS.1 Allowable Stresses 1.5*
AS2 Wind and Seismic Stresses 1.5.6
AS3 Structural Analysis =
ASA Design for Serviceability and _
other Considerations
A6 Referenced Codes and Standards _
AT Design Documents
ATL Plans Lat
AT2 Standard Symbols and Nomenclature 11.4"
AT3 Notation for Welding 1.13
* first paragraph only
Amrnican Insrrrure oF Stites, Coxstaucrion5-3
1989 Spec. 1978 Spec.
Chapter B DESIGN REQUIREMENTS
BL Gross Area 1.14.1*/3
B2 Net Area 114.1844
1.14.2.1
B3 Effective Net Area 1,14.2.2/3
B4 Stability 1.8.1+
BS Local Buckling 1.9
BS.1 Classification of Steel Sections 1.9.1++/2
BS.2 Slender Compression Elements 19.14++
B6 Rotational Restraint at Points 1.40.14
of Support
B7 Limiting Slenderness Ratios 1.8.4
BS Simple Spans 1124
BY End Restraint 1.12.2
B10 Proportions of Beams and Girders 4.10.1/3/4
Bll Proportioning of Crane Girders 1.10.9
Chapter C FRAMES AND OTHER STRUCTURES
cL General —
a Frame Stability
C21 Braced Frames 1.8.2
2.2 Unbraced Frames 1.8.3
Chapter D TENSION MEMBERS
DI Allowable Stress 15.11
D2 Built-up Members 1.18.3
D3 Pin-Connected Members _
D3.1 Allowable Stress 15.1.1
D3.2 Pin-connected Plates 1.14.5***
D3.3 Eyebars LAGS + +++
* except net
** except gross
** except first two paragraphs
+ first paragraph only
++ except last paragraph
+++ last paragraph only
F-+++ first two paragraphs only
Aeenican Insrrrurs oF Steet Coxstaucrion