Академический Документы
Профессиональный Документы
Культура Документы
PD60285
IR3315(S)PbF
LOW EMI CURRENT SENSE HIGH SIDE SWITCH
Features
Load current feedback Programmable over current shutdown Active clamp ESD protection Input referenced to Vcc Over temperature shutdown Reverse battery protection Lead-Free
Product Summary Rds(on) 20 m max. Vcc op. 6 to 32V Current Ratio 2800 Prog. Ishutdown 3 to 30A Vclamp 40V Packages
Description
The IR3315(S)PbF is a fully protected 4 terminals high side switch. The input signal is referenced to Vcc. When the input voltage Vcc - Vin is higher than the specified threshold, the output power Mosfet is turned on. When the Vcc - Vin is lower than the specified Vil threshold, the output Mosfet is turned off. A current proportional to the power Mosfet current is sourced to the Ifb pin. Over current shutdown occurs when Vst-Vin > 4.5V. The current shutdown threshold is adjusted by selecting the proper RIfb. Either over current and over temperature latches off the switch. The device is reset by pulling the input pin high. Other integrated protections (ESD, reverse battery, active clamp) make the switch very rugged in automotive environment.
TO-220 IR3315PbF
Typical Connection
Vcc IN Ifb
IR3315
Battery Out
10k
Load
www.irf.com
IR3315(S)PbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Vcc lead. (Tambient=25C unless otherwise specified).
Symbol
Parameter
Min.
-16 -16 -16 -0.3
Max.
37 32 33 37 2.8 100 2 4 0.5 150
Units
V
Vcc-Vin Maximum Vcc voltage Vcc-Vin cont. Maximum continuous Vcc voltage Vcc-Vfb Maximum Ifb voltage Vcc-Vout Maximum output voltage Ids cont. Maximum body diode continuous current Rth=60C/W (1) Ids pulsed Maximum body diode pulsed current (1) Pd Maximum power dissipation Rth=60C/W ESD1 Electrostatic discharge voltage (Human body) C=100pF, R=1500 ESD2 Electrostatic discharge voltage (Machine Model) C=200pF,R=0 Tj max. Max. storage & operating temperature junction temperature Min Rfb Minimum on the resistor on Ifb pin Ifb max. Max. Ifb current (1) Limited by junction temperature. Pulsed is also limited by wiring
A W kV C k mA
50
Thermal Characteristics
Symbol
Rth1 Rth2 Rth3
Parameter
Thermal resistance junction to ambient D-Pak Std footprint Thermal resistance junction to case D-Pak Thermal resistance junction to case TO-220
Typ.
60 1.6 1.6
Max.
Units
C/W
Symbol
Iout
Parameter
Min.
Max.
14 3.9 3.5
Units
A k ms Hz
Continuous output current Tambient=85C, Rth=5C/W, Tj=125C Tambient=85C, Rth=60C/W, Tj=125C Rifb Recommended Ifb resistor (2)(3) Pulse min. Minimum turn-on pulse width Fmax. Maximum operating frequency 2) If Rifb is too low, the device can be damaged. 3) If Rifb is too high, the device may not switch on.
0.5 1
200
www.irf.com
IR3315(S)PbF
Protection Characteristics
Tj=25C, Rifb=500 to 5k
Symbol
Vifb-Vin@Isd Tsd OV Isdf Isd_1k Treset Min. pulse WAIT Rds(on) rev.
Parameter
Over-current shutdown threshold Over temperature threshold Over voltage protection (not latched) Fixed over current shutdown Programmable over current shutdown 1k Time to reset protection Min. pulse width (no WAIT state) WAIT function timer Reverse battery On state resistance
Min.
4
Typ.
4.7 165 35 38 12 50 400 1 16
Max.
5.6
Units
V C V A s ms m
Test Conditions
See fig. 5 Vifb<Vifb-Vin@Isd Rifb=1k See fig. 5 See fig. 4 and 5 Vcc-Vin=-14V, Iout=10A
33 30 9
200 0.4 10
39 47 16 500 1200 2 28
Symbol
Vcc op. Icc off Iin, on Vih Vil Vhyst Iout
Parameter
Operating Voltage range Supply leakage current On state IN positive current High level Input threshold voltage (4) Low level Input threshold voltage (4) Input hysteresis Vih-Vil Drain to source leakage current
Min.
6
Typ.
Max.
32 5 6 6.2 5.8 1 5
Units
V A mA V A
Test Conditions
Vin=Vcc, Vcc-Vout=14V, Vcc-Vifb=14V Vcc-Vin=14V
1.5
4 0.2
Vin=Vcc, Vcc-Vifb=0V, Vcc-Vout=14V Rds(on) On state resistance (5) Tj=25C 10 15 20 Iout=10A, Vcc-Vin=14V On state resistance (5) Tj=25C 10 16 28 Iout=7A, Vcc-Vin=6V m On state resistance (5) Tj=150C 20 28.5 38 Iout=10A, Vcc-Vin=14V Iout=50mA V clamp1 Vcc to Vout clamp voltage 1 36 39 V 40 43 Iout=10A V clamp2 Vcc to Vout clamp voltage 2 (4) Input thresholds are measured directly between the input pin and the tab. Any parasitic resistance in common between the load current path and the input signal path can significantly affect the thresholds. (5) Rdson is measured between the tab and the Out pin, 5mm away from the package.
Symbol
Tdon Tr1 Tr2 Eon Tdoff Tf Eoff
Parameter
Turn on delay time to 10% Vcc Rise time to Vcc-Vout=5V Rise time to Vcc-Vout=0.1Vcc Turn on energy Turn off delay time Fall time to Vout=10% of Vcc Turn off energy
Min.
3 1 2
Typ.
11 4 8 0.2 40 8 0.1
Max.
27 10 20
Units
s mJ s mJ
Test Conditions
See figure 2
10 2
100 20
www.irf.com
IR3315(S)PbF
Current Sense Characteristics
Symbol
Ratio Ratio_TC Offset Trst
Parameter
I Load/Iifb current ratio I Load/Iifb variation aver temperature Load current diagnostic offset Ifb response time (low signal)
Min.
2,400 -5 -0.08
Typ.
2,800
Max.
3,200 +5 +0.07
Units
Test Conditions
Tj=25C, Rfb=500, Iout=20A Tj=-40C to 150C Iout=1A 90% of the Iout step
0 1
% A s
VCC
Charge Pump
Driver
On/Off Fast turn-off 43V 38V
43V
3mA
43V
Latch
Wait timer 1 ms 4.7V timer 400s 80 + Iout > 38A Tj > 165C Min. Pulse +
IN
IFB OUT
www.irf.com
IR3315(S)PbF
Lead Assignments
3- Vcc 3- Vcc
12
45
DPak TO220
90%
Vcc-Vin
10%
Tr-in
90% Vcc-5V
Vout
10%
Ifb
Iout Isd
Td on Tr1 Tr2
Td off Tf
www.irf.com
IR3315(S)PbF
Vin
T clamp
Vcc-Vin
Iout
Vcc
T min. pulse
T min. pulse
Iout
Wait
Vout
Vcc - V clamp
Vcc-Vin
t < T reset
t < T reset
Over-current shutdown
Iout
Over-temperature shutdown
Tj
www.irf.com
IR3315(S)PbF
All curves are typical characteristics. Operation in hatched areas is not recommended. Tj=25C, Rifb=500ohm, Vcc=14V (unless otherwise specified).
1 0
6
200%
6 5
150%
4 3 2 1 0
100%
-50
-25
25
50
75
100
125
150
Tj, junction temperature (C) Figure 9 Vih, Vil and Vifb-Vin@Isd (V) Vs Tj (C)
www.irf.com
IR3315(S)PbF
100
With calibration
Spec. Max.
4
Error (+/-A)
10
0 0 5 10 15
15
60C/W 35C/W
100
10
10
1 10 100
Tamb., ambient temperature (C) Figure 12 Max. Iout (A) Vs Tamb. (C)
www.irf.com
IR3315(S)PbF
100
10
5C/W
10
0.1
1 1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
Protection response time (s) Figure 14 Ids (A) Vs over temperature protection response time (s)
www.irf.com
IR3315(S)PbF
Case Outline TO220 5 leads - Automotive Q100 PbF qualified
www.irf.com
10
IR3315(S)PbF
Case Outline 5 Lead - D2PAK - Automotive Q100 PbF MSL1 qualified
www.irf.com
11
IR3315(S)PbF
Tape & Reel 5 Lead - D2PAK
D2Pak is MSL1 qualified. This product has been designed and qualified for the Automotive [Q100] market. Qualification standards can be found at www.irf.com IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. 9/6/2006
www.irf.com
12
Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/