Академический Документы
Профессиональный Документы
Культура Документы
As is generally known to everyone, black powder is a mixture of saltpeter, charcoal and sulfur. To disappoint all of you who think, in the following paper I'm going to give away an optimum recipe with the best possible performance, I state here once and for all: The mixture of the three ingredients is of little importance. It is the method of making the charcoal that counts, as I will prove with this chapter. But back to the black powder recipe: You can change it in a wide range, without noticing any difference between the charges. That explains, why most of the historic recipes differ in a wide range. On the other hand, it is hard to find a historic recipe on how to char the coal, since that usually was a state secret. By the way, even a mixture of saltpeter and charcoal without sulfur explodes remarkably well. However, a mixture of saltpeter and sulfur, without charcoal, doesn't burn at all. The latter fact puzzled the chemists throughout the centuries, because sulfur alone burns pretty well and saltpeter generally accelerates all sorts of fires. Note: Charcoal does not consist of pure carbon (C) as most authors pretend. Such a pure charcoal would require a charring temperature of at least 1,500 C! And a black powder mixed with it would probably burn like the head of a matchstick, at best. As I'm explaining in my charcoal chapter, the formula of charcoal may be best described as C7H4O. With this and the following chemical equations we'll see why there won't be an explicit, best mixture of black powder: Depending on the portion of charcoal, its carbon produces alternatively carbon dioxide or carbon monoxide or a mix of both. To these you'll have to add the water vapor plus nitrogen, released from the saltpeter. So the sum of all the gases is nearly the same on all recipes. Indeed, the following three dimensional graph of the performance of different black powder recipes reveals a flat top over wide rage of recipes. A recipe without sulfur yields only little less energy (Joule/g). But its advantage lies in its little smoke produced. Its fog then consists of potassium carbonate (potash). Unfortunately its ignition temperature is 100 C higher than usual. For cap lock arms no problem, but a nuisance to flint and match lock sportsmen. Here the chemical equation for a regular black powder containing sulfur: 1) 4 KNO3 + C7H4O + 2 S ------> 2 K2S + 4 CO + H2O + N2
and for a blackpowder without sulfur: 2) 4 KNO3 + C7H4O ------> 2 K2CO3 + CO2 + CO2 + H2O + N2
Legend:
KNO3 C is saltpeter stands for carbon
s sulfur stands for potassiumsulfide (responsible for the white smoke of blackpowder) s pot ash is carbon monoxide is carbon dioxide, and is Nitrogen
Reasonable recipes are; A standard black powder:..100 parts saltpeter + 18 parts coal + 16 parts sulfur A powder without sulfur: ....100 parts saltpeter + 24 parts coal As you noticed, I always give powder recipes on the basis of 100 parts saltpeter! Then, with the three ingredients, it leaves only two variables which can be compared or drawn on graphs easily. For the creation of the following graph showing the performance of black powder, I tested dozens of recipes and fired some hundred shots. The black powder samples were always mixed from saltpeter and sulfur supplied by the chemical industry. The charcoal I made from the wood of a willow tree, in fact from its young, debarked branches of approximately 3 to 4 cm diameter, charred in a tin can at 400 C until smokefree.
The muzzle energy was determined by the measurement of the bullet velocity, one meter ahead of the muzzle of a three band Enfield rifle, cal. 58 (14.7 mm) and a patched round ball of 17.3 g lead. The velocity was measured by a commercially available chronograph. With each recipe there were three shots fired and from these the median was taken. The load was exactly 2.00 g black powder. Then the muzzle energy was calculated as: 3) Energy (Joule) = Mass of the ball (kg) velocity2 (m/s)2
Fig 2: And here is what I shot with Bacons recipe by volume: 3 shots bench-rest, at 25 meters with a muzzle loader pistol cal. 38.
Here are some other local recipes, used historically : Saltpeter parts 100 100 100 100 Charcoal parts 33 16.7 17.3 20.0 Sulfur parts 12 16.7 16.0 13.3
Marcus Graecus (ca. 1250) Canton of Zurich (1775) Swiss Army (1849) Modern Swiss Powder
According to Fig. 1 the muzzle energies of the latter three recipes cover the top of the blue cap of the diagram and hence can't be improved. That proves, the optimum mixture of black powder has been found not later than mid 18th century. But also the recipe of Marcus Graecus (exact date uncertain) shows good results. The role of Sulfur in black powder
Contemplating the diagram in Fig. 1, you might ask yourself, why on earth did our ancestors take the trouble to add sulfur at all? That idea first occured to the Swiss artillery in 1875, when "smokeless black powder" was tested. Firing salvos out of a fortification soon made the enemy invisible, due to the heavy smoke of the hefty loads of cannons. Since those tests were done on the eve of the "white-powder" era, the findings soon became obsolete. A sulfur-free black powder yields only little smoke. When it is used in a rifle, you see only a faint fog. When a percussion rifle is fired, the ignition poses no problems. From a flint lock, you will get a lot of misfires. So I tested the ignition temperature of (homemade) black powders by increasing the temperature in a laboratory oven in increments of 10C and found the purpose of sulfur in the black powder mixture:
Ignition Temperatures: S'peter 100 p 100 p p = parts The sole purpose of sulfur in a black powder mixture is the reduction of the ignition temperature! Note: A good priming powder has allways a high sulfur concentration. Charcoal 13 p 27 p Sulfur 12 p 0p Ignition-Temp. 300 C 440 C