Академический Документы
Профессиональный Документы
Культура Документы
TV and FM Broadcasting
Wireless Internet
4
5
+
4
5
+
4
5
4
5
Layout of interface
B
e
a
m
B
(
+
3
0
)
B
e
a
m
A
(
3
0
)
Mounting Clamps Included
Beam A Beam B
116
30
210
60
240
90 270
120
300
150
330
180
0
Antenna I
BeamA
Antenna II
Beam B
Antenna II
BeamA
Antenna III
Beam B
Antenna III
BeamA
Antenna I
Beam B
0
3
6
10
20
D
o
u
t
4
7
0
m
m
Antenna I
Antenna II
Antenna III
Horizontal Patterns (top view)
Bottom view
A
Torque 5.9 ft-lb
(8 Nm)
B
C
D
60
Mounting support clamp
E
F
3 sector clamp
(supports the antenna assembly
during azimuth adjustment)
Specications: 742 034 Sector Bracket
Angle between antennas 120
Suitable for mast diameter* 5.5 inches (139.7 mm) OD.
Number of pieces 2 x 3 sector clamp
2 x mounting support clamp
Materials
3 sector clamp Hot-dip galvanized steel
Mounting support clamp Aluminum
Fasteners Stainless steel
Outer diameter (Dout) of the 18.5 inches (470 mm)
3 Dual-beam Panel Arrangement
* Customer assumes all responsibility to ensure that the mounting
pipe is adequate to support the intended load. For use with steel
pipe only (not aluminum) with a minimum 0.25 inch (6 mm) wall
thickness.
17102200 MHz Split Beam Panel Antenna
XX Polarization
800 10606V01
Specications: 3 Panel Arrangement
Weight 130.1 lb (59 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 214 lbf / 214 lbf / 214 lbf
(950 N) / (950 N) / (950 N)
Wind survival rating 120 mph (200 kph)
Dimensions: 742 034 sector bracket with 800 10606 antennas
A B C D E F Dout
inches 5.5 3.9 9.3 9 1.9 1.8 18.5
mm 139.7 100 236 228 49 45 470
117
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Electrical downtilt 08 degrees
continuously adjustable
Tracking 0.5 dB
Squint 1.5
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 55.4 x 6.1 x 2.8 inches
(1407 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 81 lbf / 32 lbf / 81 lbf
(360 N) / (140 N) / (360 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 65.8 x 6.8 x 4.4 inches
(1672 x 172 x 112 mm)
Shipping weight 22 lb (10 kg)
17102200 MHz Panel Antenna
X Polarization
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 18.3 dBi 18.7 dBi 19 dBi
+45 and -45 polarization 65 (half-power) 62 (half-power) 59 (half-power)
horizontal beamwidth
+45 and -45 polarization 6.6 (half-power) 6.2 (half-power) 5.9 (half-power)
vertical beamwidth
Front-to-back ratio (1803) >30 dB >30 dB >28 dB
Sidelobe suppression for 0 4 8 0 4 8 0 4 8
rst sidelobe above main beam >18 14 14 dB >18 15 15 dB >18 15 15 dB
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
11235-A
936.3588/a
62
17102200 MHz
X - POL
Adjustable Electrical Downtilt
08
Remote Control Option
800 10636
Vertical pattern
45- polarization
08 electrical downtilt
Horizontal pattern
45- polarization
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200
45o
17102200
+45o
7-16 7-16
6.1 inches
(155 mm)
55.4 inches
(1407 mm)
58.3 inches
(1480 mm)
2.8 inches
(70 mm)
57 inches
(1449 mm)
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Prole PF10
Mounting Clamps Included
118
General specications:
Frequency range 17102690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female (long neck)
Electrical downtilt 012 (continously adjustable)
(manual or remote control)
Isolation, between ports >30 dB
Maximum input power 250 watts (at 50C) per input
Weight 11 lb (5 kg)
Dimensions 33.5 x 6.1 x 2.8 inches
(851 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 48 lbf / 14 lbf / 50 lbf
(210 N) / (60 N) / (220 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 45.1 x 6.8 x 3.6 inches
(1146 x 172 x 92 mm)
Shipping weight 14.3 lb (6.5 kg)
17102690 MHz Panel Antenna
X Polarization
Specications: 17101990 MHz 19202200 MHz 22002490 MHz 24902690 MHz
Gain 15.5 dBi 16.3 dBi 16.7 dBi 16.7 dBi
+45 and -45 polarization 67 (half-power) 64 (half-power) 60 (half-power) 60 (half-power)
horizontal beamwidth
+45 and -45 polarization 10.8 (half-power) 9.9 (half-power) 8.8 (half-power) 8.4 (half-power)
vertical beamwidth
Front-to-back ratio >25 dB >25 dB >23 dB >23 dB
(18030)
Sidelobe suppression for: 0 6 12 T 0 6 12 T 0 6 12 T 0 6 12 T
First sidelobe above main beam >12 13 15 dB >13 14 15 dB >13 14 16 dB >15 15 17 dB
Cross polar ratio 0 25 dB (typical) 28 dB (typical) 28 dB (typical) 28 dB (typical)
Sector 60 >9 dB >8 dB >8 dB >11 dB
11214-B
936.4019/a
Mounting Equipment:
Model Description
734 365 Mounting Kit for 1.8 to 4.9 inch
(45 to 125 mm) OD mast.
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(optional) (50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 025 degrees downtilt angle for use with
2 x 738 546 mounting kit
Reference the Mechanical Accessories section.
6.1 inches
(155 mm)
45o +45o
33.5 inches
(851 mm)
36.5 inches
(926 mm)
2.8 inches
(70 mm)
35.3 inches
(896 mm)
2.625 inches
0.125
65
17102690 MHz
X - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10681
Prole PF5
17102690
45o
17102690
+45o
7-16 7-16
Vertical pattern
45- polarization
012 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
119
General specications:
Frequency range 17102690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Electrical downtilt 012 (continously adjustable)
(manual or remote control)
Isolation, between ports >30 dB
Maximum input power 250 watts (at 50C) per input
Weight 24.3 lb (11 kg)
28.7 lb (13 kg) clamps included
Dimensions 33.7 x 12.7 x 2.8 inches
(855 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 99 lbf / 23 lbf / 104 lbf
(440 N) / (100 N) / (460 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 45.1 x 13.3 x 4.1 inches
(1146 x 337 x 104 mm)
Shipping weight 32 lb (14.5 kg)
17102690 MHz Panel Antenna
XX Polarization
Specications: 17101990 MHz 19202200 MHz 22002490 MHz 24902690 MHz
Gain 15.8 dBi 16.2 dBi 16.6 dBi 16.7 dBi
+45 and -45 polarization 65 (half-power) 64 (half-power) 60 (half-power) 61 (half-power)
horizontal beamwidth
+45 and -45 polarization 11 (half-power) 10 (half-power) 9 (half-power) 8.7 (half-power)
vertical beamwidth
Front-to-back ratio (co-polar) >30 dB >30 dB >30 dB >28 dB
Sidelobe suppression for 0 6 12 T 0 6 12 T 0 6 12 T 0 6 12 T
First sidelobe above main beam >12 13 15 dB >13 14 16 dB >13 15 16 dB >15 15 17 dB
Cross polar ratio 0 25 dB (typical) 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >8 dB >8 dB >8 dB >10 dB
11215-A
936.3770/b
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 025 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102690 MHz
17102690 MHz
XX - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10682
17102690
45o
17102690
+45o
7-16 7-16
17102690
+45o
7-16
17102690
45o
7-16
33.7 inches
(855 mm)
41.7 inches
(1066 mm)
2.8 inches
(71 mm)
36.2 inches
(920 mm)
2.625 inches 0.125
(68 mm 4)
12.7 inches
(323 mm)
Vertical pattern
45- polarization
012 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Prole PF8
Mounting Clamps Included
120
General specications:
Frequency range 17102170 MHz / 24902690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Isolation >30 dB (intrasystem)
>29 dB (intersystem)
Weight 22 lb (10 kg)
26.5 lb (12 kg) clamps included
Dimensions 55.5 x 6.1 x 3.5 inches
(1410 x 155 x 89 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 84 lbf / 33 lbf / 90 lbf
(370 N) / (145 N) / (400 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 69.5 x 7.2 x 4.8 inches
(1765 x 182 x 122 mm)
Shipping weight 30.9 lb (14 kg)
17102170 MHz / 24902690 MHz Panel Antenna
XX Polarization
Specications: 17101990 MHz 19202170 MHz 24902690 MHz
Gain 17.5 dBi 17.7 dBi 18 dBi
+45 and -45 polarization 68 (half-power) 65 (half-power) 61 (half-power)
horizontal beamwidth
+45 and -45 polarization 6.7 (half-power) 6.3 (half-power) 5.4 (half-power)
vertical beamwidth
Front-to-back ratio (18030) >25 dB >25 dB >25 dB
Electrical downtilt 010 degrees 010 degrees 010 degrees
continuously adjustable
Sidelobe suppression for 0 5 10 T 0 5 10 T 0 5 10 T
rst sidelobe above main beam >17 17 16 dB >17 17 16 dB >17 17 16 dB
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >8 dB >8 dB >10 dB
Maximum input power 200 watts per input 200 watts per input
(at 50C) 400 watts total 400 watts total
11311-B
936.3803/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 015 degrees downtilt angle
Reference the Mechanical Accessories section.
65
17102170 MHz
24902690 MHz
XX - POL
Adjustable Electrical Downtilt
010
800 10644
24902690 MHz
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
17102170 MHz
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
N
E
W
Prole PF11
Mounting Clamps Included
121
55.5 inches
(1410 mm)
59.4 inches
(1509 mm)
3.5 inches
(89 mm)
58.2 inches
(1479 mm)
6.1 inches
(155 mm)
2.625 inches 0.125
(68 mm 4)
17102170
+45o
24902690
45o
7-16 7-16
17102170
45o
7-16
24902690
+45o
7-16
17102170 MHz / 24902690 MHz Panel Antenna
XX Polarization
800 10644
122
17102200 MHz Panel Antenna
X Polarization
11298-A
936.3924/b
General specications:
Frequency range 17102200 MHz
VSWR <1.4:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 0.5 dB
Squint 2
Weight 9.9 lb (4.5 kg)
Dimensions 28.9 x 6.1 x 2.7 inches
(735 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 44 lbf / 16 lbf / 50 lbf
(195 N) / (70 N) / (220 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 40 x 6.8 x 3.6 inches
(1015 x 172 x 92 mm)
Shipping weight 12.1 lb (5.5 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain tilt 0 4 8 12 0 4 8 12 0 4 8 12
dBi 15.5 15.4 15.3 15.1 15.6 15.5 15.4 15 15.8 15.7 15.5 14.9
+45 and -45 polarization 67 (half-power) 66 (half-power) 64 (half-power)
horizontal beamwidth
+45 and -45 polarization 12.9 (half-power) 12.3 (half-power) 11.5 (half-power)
vertical beamwidth
Electrical downtilt 012 012 012
continously adjustable
Front-to-back ratio >27 dB (co-polar) >27 dB (co-polar) >27 dB (co-polar)
Sidelobe suppression
for rst sidelobe tilt 0 4 8 12 0 4 8 12 0 4 8 12
above main beam dB > 14 14 14 14 14 14 14 14 14 14 14 14
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
012 electrical downtilt
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
7-16 DIN 7-16 DIN
1710/2200
-45
1710/2200
+45
45o +45o
28.9 inches
(735 mm)
32.2 inches
(819 mm)
2.7 inches
(69 mm)
31 inches
(789 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10247V01
Prole PF5
Mounting Equipment:
Model Description
734 365 Mounting Kit for 1.8 to 4.9 inch
(45 to 125 mm) OD mast.
732 327 Tilt Kit for use with the above
mounting kits,
040 degrees downtilt angle.
Reference the Mechanical Accessories section.
Mounting Clamps Included
123
45o +45o
51.7 inches
(1314 mm)
54.6 inches
(1386 mm)
2.8 inches
(70 mm)
53.4 inches
(1356 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Electrical downtilt 210 degrees
continuously adjustable
Tracking 0.5 dB
Squint 1.5
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 51.7 x 6.1 x 2.8 inches
(1314 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 21 lbf / 77 lbf
(330 N) / (90 N) / (340 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 62.8 x 6.8 x 3.6 inches
(1595 x 172 x 92 mm)
Shipping weight 22 lb (10 kg)
17102200 MHz Panel Antenna
X Polarization
11236-A
936.3531/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
210
Remote Control Option
800 10614V01
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.3 dBi 17.7 dBi 18 dBi
+45 and -45 polarization 66 (half-power) 64 (half-power) 62 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.9 (half-power) 7.5 (half-power) 7.2 (half-power)
vertical beamwidth
Front-to-back ratio (1803) >25 dB >25 dB >25 dB
Sidelobe suppression for
rst sidelobe above main beam >15 dB >17 dB >18 dB
Sidelobe suppression
in the sector 40180 below >23 dB >24 dB >25 dB
horizon for Tx-Frequencies
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
17102200
45o
17102200
+45o
7-16 7-16
Vertical pattern
45- polarization
210 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Prole PF5
Mounting Clamps Included
124
17102690 MHz Panel Antenna
X Polarization
11261-A
936.3887b
General specications:
Frequency range 17102690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts per input
Tracking 1.0 dB
Squint 2.5
Weight 17.6 lb (8 kg)
22 lb (10 kg) clamps included
Dimensions 55.1 x 6.1 x 2.7 inches
(1400 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 84 lbf / 31 lbf / 95 lbf
(370 N) / (135 N) / (420 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 66.3 x 6.8 x 3.6 inches
(1685 x 172 x 92 mm)
Shipping weight 25.1 lb (11.4 kg)
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Kit for use with above mounting kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
Specications: 17101990 MHz 19202200 MHz 22002490 MHz 24902690 MHz
Gain 0 6 12 T 0 6 12 T 0 6 12 T 0 6 12 T
17.4 17.4 17.3 dBi 18.2 18 17.9 dBi 18.2 18.1 17.7 dBi 18.3 18 17.6 dBi
Front-to-back ratio (18030) >25 dB >25 dB >25 dB >25 dB
+45 and -45 polarization 68 (half-power) 64 (half-power) 61 (half-power) 60 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.1 (half-power) 6.5 (half-power) 5.9 (half-power) 5.7 (half-power)
vertical beamwidth
Electrical downtilt 012 012 012 012
continuously adjustable (manual or optional remote control)
Sidelobe suppression 0 6 12 T 0 6 12 T 0 6 12 0 6 12 T
rst sidelobe above main beam >18 18 18 dB >18 18 18 dB >18 17 17 dB >18 18 16 dB
within 020 sector above horizon >17 17 16 dB >17 17 16 dB >16 18 17 dB >15 15 14 dB
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB >10 dB
65
17102690 MHz
X - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10621V01
Prole PF8
55.1 inches
(1400 mm)
58.4 inches
(1484 mm)
57.2 inches
(1454 mm)
2.5 inches
(64 mm)
17102690
45o
17102690
+45o
7-16 7-16
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
012 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
2.7 inches
(69 mm)
6.1 inches
(155 mm)
45o +45o
Mounting Clamps Included
125
17102690 MHz Panel Antenna
XX Polarization
11237-B
936.3621/b
General specications:
Frequency range 17102690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Electrical downtilt 012 (continously adjustable)
(manual or remote control)
Isolation, between ports >30 dB
Maximum input power 300 watts (at 50C) per input
Weight 39.7 lb (18 kg)
44.1 lb (20 kg) clamps included
Dimensions 55.7 x 12.7 x 2.8 inches
(1415 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 162 lbf / 38 lbf / 167 lbf
(720 N) / (165 N) / (740 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 67.2 x 13.3 x 4.4 inches
(1706 x 337 x 112 mm)
Shipping weight 48.5 lb (22 kg)
Specications: 17101990 MHz 19202200 MHz 22002490 MHz 24902690 MHz
Gain 0 6 12 T 0 6 12 T 0 6 12 T 0 6 12 T
17.4 17.4 17.3 dBi 17.8 17.6 17.5 dBi 18 17.9 17.5 dBi 18 17.7 17.3
dBi
+45 and -45 polarization 65 (half-power) 65 (half-power) 61 (half-power) 61 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.1 (half-power) 6.5 (half-power) 5.9 (half-power) 5.7 (half-power)
vertical beamwidth
Front-to-back ratio (18030) >25 dB, avg 28 dB >26 dB, avg 28 dB >25 dB, avg 27 dB >25 dB, avg 27 dB
Sidelobe suppression for: 0 6 12 T 0 6 12 T 0 6 12 T 0 6 12 T
First sidelobe above main beam >18 18 18 dB >18 18 18 dB >18 17 17 dB >18 18 17 d
Cross polar ratio 0 30 dB (typical) 30 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >8 dB >10 dB
65
17102690 MHz
17102690 MHz
XX - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10622
Prole PF8
55.7 inches
(1415 mm)
59.8 inches
(1520 mm)
58.3 inches
(1480 mm)
2.625 inches 0.125
(68 mm 4)
17102690
45o
17102690
+45o
7-16 7-16
17102690
+45o
7-16
17102690
45o
7-16
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Kit for use with above mounting kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
012 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
2.8 inches
(71 mm)
12.7 inches
(323 mm)
Mounting Clamps Included
126
17102170 MHz Panel Antenna
X Polarization
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio 30 dB (co-polar)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 08 degrees
continuously adjustable (manual or optional remote control)
Connector 2 x 7-16 DIN female
Isolation >30 dB
Tracking 1 dB
Squint 2.5
Weight 9.9 lb (4.5 kg)
14.3 lb (6.5 kg) clamps included
Dimensions approx. 45 x 6.1 x 2.8 inches (1142 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 66 lbf / 18 lbf / 68 lbf
(290 N) / (80 N) / (300 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 56.1 x 6.8 x 3.7 inches (1425 x 172 x 95 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 17.5 dBi 17.7 dBi 18 dBi
+45 and -45 polarization 66 (half-power) 64 (half-power) 62 (half-power)
horizontal beamwidth
+45 and -45 polarization 8.3 (half-power) 7.8 (half-power) 7.4 (half-power)
vertical beamwidth
Sidelobe suppression for: 0 4 8 T 0 4 8 T 0 4 8 T
1
st
sidelobe above horizon, avg. 20 20 20 dB 20 20 20 dB 20 20 20 dB
Cross polar ratio 0 25 dB (typical) 25 dB (typical) 28 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
11266-A
936.3886/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102170 MHz
X - POL
Adjustable Electrical Downtilt
08
Remote Control Option
742 214V01
46.7 inches
(1186 mm)
6.1 inches
(155 mm)
45 inches
(1142 mm)
2.8 inches
(70 mm)
2.5 inches
(64 mm)
47.9 inches
(1216 mm)
17102170
-45
17102170
+45
7-16 DIN 7-16 DIN
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
08 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Prole PF5
Mounting Clamps Included
127
17102200 MHz Panel Antenna
X Polarization
General specications:
Frequency range 17102200 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
(180 30) >25 dB (total power)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 010 degrees
continuously adjustable
Connector 2 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Tracking, average 0.5 dB
Squint 1.5
Weight 14.3 lb (6.5 kg)
18.3 lb (8.3 kg) clamps included
Dimensions 51.7 x 6.1 x 2.8 inches
(1314 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 21 lbf / 77 lbf
(330 N) / (90 N) / (340 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 62.8 x 6.8 x 3.6 inches
(1595 x 172 x 92 mm)
Shipping weight 22 lb (10 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.7 dBi 17.9 dBi 18 dBi
+45 and -45 polarization 68 (half-power) 66 (half-power) 64 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.1 (half-power) 6.8 (half-power) 6.4 (half-power)
vertical beamwidth
Vertical Patternsidelobe 0 4 8 10 0 4 8 10 0 4 8 10
suppression for rst side- 18 18 17 17 dB 18 18 17 17 dB 18 18 17 17 dB
lobe above main beam
11272-A
936.3733/b
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 013 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200
-45
17102200
+45
7-16 DIN 7-16 DIN
53.4 inches
(1356 mm)
51.7 inches
(1314 mm)
54.6 inches
(1386 mm)
2.5 inches
(64 mm)
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
010
Remote Control Option
742 215V01
6.1 inches
(155 mm)
2.8 inches
(70 mm)
Prole PF10
Mounting Clamps Included
128
17102200 MHz Panel Antenna
X Polarization with Integrated Remote Downtilt
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(optional) (50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
General specications:
Frequency range 17102200 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
>25 dB (total power)
Maximum input power 120 watts per input (at 50C)
Electrical downtilt 010 degrees
continuously adjustable
Connector 2 x 7- 16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Weight 16.5 lb (7.5 kg)
Dimensions 51.3 x 6.1 x 2.7 inches (1302 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 26 lbf / 88 lbf
(330 N) / (115 N) / (390 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 55.3 x 6.8 x 3.6 inches (1404 x 172 x 92 mm)
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
10920-F
936.2890/e
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.7 dBi 17.9 dBi 18 dBi
+45 and -45 polarization 67 (half-power) 66 (half-power) 65 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.1 (half-power) 6.8 (half-power) 6.6 (half-power)
vertical beamwidth
Sidelobe suppression for 0 4 8 10 0 4 8 10 0 4 8 10
rst sidelobe above main beam 16 16 16 16 dB 17 17 17 17 dB 17 17 17 17 dB
IRT specications:
Power supply 1030 V
Power Consumption < 1 W (standby); < 8.5 W (motor activated)
Hardware interface
1
2 x 8 pin connector according to IEC 60130-9;
IRT in (male): Control / Daisy chain in, conforming with AISG
IRT out (female): Daisy chain out, conforming with AISG
Logical interface
2
AISG 1.1 800 10314
ex factory 3GPP / AISG 2.0 800 10618
Protocols AISG 1.1 and 3GPP / AISG 2.0 compliant
Adjustment time (full range) 40 seconds
Adjustment cycles >50,000
Certication FCC 15.107 Class B Computing Devices
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
010
with Integrated
Remote Downtilt
800 10314, 800 10618
Prole PF5
1
Tightening torque for xing the connector must
lie between 0.5 1.0 Nm (0.360.73 lb/ft).
2
The protocol of the logical interface can
be switched from AISG 1.1 to 3GPP/AISG
2.0 and vice versa with a vendor specific
command. Start-up operation of the 800
10314 is only possible with a primary station
supporting AISG 1.1 and start-up operation
of the 800 10618 is only possible with a
primary station supporting 3GPP/AISG 2.0!
Please note: The used Primary-SW has to
be able to handle also integrated remote tilt
units, like Kathrein CCU with rmware 1.29
or higher and the Kathrein PCA with SW 2.0
or higher. If the Primary of the system doesnt
support the standard of the logical interface
ex factory, the IRT must be switched to the
appropriate standard of the Primary before
installation. Please contact Kathrein for further
information.
Order Information:
Model Description
800 10314 Antenna with AISG 1.1 linterface
010 adjustable electrical downtilt
800 10618 Antenna with 3GPP / AISG 2.0 interface
010 adjustable electrical downtilt
129
6.1 inches
(155 mm)
54.6 inches
(1386 mm)
51.3 inches
(1302 mm)
2.7 inches
(69 mm)
53.4 inches
(1356 mm)
2.5 inches
(64 mm)
45o +45o
1710-2200
+45o
RT
in out
7-16 8pin
male
1710-2200
-45o
7-16 8pin
female
Daisy chain configuration
RT RT RT
Central Control Unit (CCU)
or
Portable Control Adapter (PCA)
a
n
n
e
t
n
A
a
n
n
e
t
n
A
a
n
n
e
t
n
A
ASG
Star configuration
RT RT RT
Central Control Unit (CCU)
or
Portable Control Adapter (PCA)
a
n
n
e
t
n
A
a
n
n
e
t
n
A
a
n
n
e
t
n
A
ASG
3:1 Splitter
800 10314, 800 10618
17102200 MHz Panel Antenna
X Polarization with Integrated Remote Downtilt
Connecting the control cables:
1. Stand alone / Star configuration:
Connect the control cable to the IRT in input of the antenna. If daisy chain is not
required, do not remove the protection cap of the IRT out input.
2. Daisy chain configuration:
For the daisy chain solution, remove the protection cap (IRT out) and create a bonding
to the subsequent antenna (IRT in) via additional control cable. Do not remove
the protection cap of the last IRT out.
Please note: The connector should be hand tightened only!
The tightening torque must be in the range of 0.370.74 lb/ft (0.5 1.0 Nm).
2
5
3
7 8 6
1
4
Pin 1 10 ... 30 VDC in 10 ... 30 VDC out
Pin 2 Not connected Not connected
Pin 3 RS485-B RS485-B
Pin 4 Not connected Not connected
Pin 5 RS485-A RS485-A
Pin 6 10 ... 30 VDC in 10 ... 30 VDC out
Pin 7 DC return DC return
(grounded) (grounded)
Pin 8 Not connected Not connected
2
8
4
1 3
5
6 7
Pin assignment for IRT interface:
8
-
p
i
n
c
o
n
n
e
c
t
o
r
(
I
E
C
6
0
1
3
0
-
9
)
male female
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
KATHREIN 800 10314, 800 10618
Tested To Comply
With FCC Standards
130
17102200 MHz Panel Antenna with Extended Downtilt Range
X- polarization
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
015 electrical downtilt
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-153 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 1.5 dB
Squint 2
Weight 14.3 lb (6.5 kg)
18.7 lb (8.5 kg) clamps included
Dimensions 54.6 x 6.1 x 2.7 inches
(1387 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 81 lbf / 23 lbf / 84 lbf
(360 N) / (100 N) / (370 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 65.2 x 6.8 x 3.6 inches
(1655 x 172 x 92 mm)
11305-A
936.3927/b
45o +45o
54.6 inches
(1387 mm)
2.7 inches
(69 mm)
57.4 inches
(1459 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
56.3 inches
(1429 mm)
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
015
800 10504V01
Prole PF5
Specications: 17101880 MHz 18501990 MHz 19202170 MHz 20002200 MHz
Gain 17.5 dBi 17.6 dBi 17.7 dBi 17.8 dBi
Front-to-back ratio (180 30) > 25 dB (co-polar) > 25 dB (co-polar) > 25 dB (co-polar) > 25 dB (co-polar)
Horizontal beamwidth 68 (half-power) 66 (half-power) 64 (half-power) 62 (half-power)
Vertical beamwidth 7.9 (half-power) 7.5 (half-power) 7.2 (half-power) 7 (half-power)
Electrical downtilt 015 015 015 015
continuously adjustable (manual or optional remote control)
Sidelobe suppression 0 5 10 15 T 0 5 10 15 T 0 5 10 15 T 0 5 10 15 T
rst sidelobe above main beam >17 20 18 17 dB >16 20 18 17 dB >16 20 18 17 dB >15 20 18 15 dB
within 020 sector above horizon >16 18 18 16 dB >16 18 17 16 dB >15 18 17 16 dB >15 16 16 15 dB
Cross polar ratio
Main direction 0 22 dB (typical) 22 dB (typical) 24 dB (typical) 26 dB (typical)
Sector 60 >10 dB >10 dB >10 dB >10 dB
Null-ll at 0 tilt 21 dB 20 dB 19 dB 18 dB
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
Mounting Clamps Included
131
17102200 MHz Panel Antenna with Extended Downtilt Range
X- polarization
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-153 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Trackin, average 0.5 dB
Squint 2.5
Weight 24.3 lb (11 kg)
28.7 lb (13kg) clamps included
Dimensions 78.1 x 6.1 x 2.7 inches
(1984 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 117 lbf / 43 lbf / 142 lbf
(520 N) / (190 N) / (630 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 89.1 x 6.8 x 3.6 inches
(2264 x 172 x 92 mm)
Shipping weight 33.1 lb (15 kg)
11306-B
936.3928/a
45o +45o
78.1 inches
(1984 mm)
2.7 inches
(69 mm)
81.4 inches
(2068 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
80.2 inches
(2038 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz 20002200 MHz
Gain 0 5 10 T 0 5 10 T 0 5 10 T 0 5 10 T
(dBi) 18.5 18.7 18.5 18.7 19 18.5 18.7 19 18.4 18.7 18.9 18.3
Front-to-back ratio (180 30) >
30 dB (co-polar) >
30 dB (co-polar) >
27 dB (co-polar) >
26 dB (co-polar)
Horizontal beamwidth 67 (half-power) 65 (half-power) 64 (half-power) 63 (half-power)
Vertical beamwidth 5 (half-power) 4.8 (half-power) 4.6 (half-power) 4.4 (half-power)
Electrical downtilt 010 010 010 010
continuously adjustable (manual or optional remote control)
Sidelobe suppression 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T
rst sidelobe above main beam >20 20 18 18 dB >20 20 18 18 dB >19 20 18 18 dB >18 20 18 18 dB
within 020 sector above horizon >18 18 17 17 dB >17 18 17 15 dB >17 17 17 15 dB >17 17 14 12 dB
Cross polar ratio
Main direction 0 25 dB (typical) 22 dB (typical) 22 dB (typical) 22 dB (typical)
Sector 60 >11 dB >11 dB >11 dB >10 dB
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 011 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
010
800 10505V01
Prole PF5
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
132
17102200 MHz Panel Antenna
X Polarization
General specications:
Frequency range 17102200 MHz
VSWR < 1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
(18030) >25 dB (total power)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 06 degrees
continuously adjustable
Connector 2 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Tracking, average 0.5 dB
Squint 2.0
Weight 19.8 lb (9 kg)
24.3 lb (11 kg) clamps included
Dimensions 76.9 x 6.1 x 2.8 inches
(1954 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 115 lbf / 32 lbf / 115 lbf
(510 N) / (140 N) / (510 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 88 x 6.8 x 3.6 inches
(2235 x 172 x 92 mm)
Shipping weight 28.7 lb (13 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 19 dBi 19.2 dBi 19.5 dBi
+45 and -45 polarization 67 (half-power) 65 (half-power) 63 (half-power)
horizontal beamwidth
+45 and -45 polarization 4.7 (half-power) 4.5 (half-power) 4.3 (half-power)
vertical beamwidth
Sidelobe suppression for rst 0 2 4 6 T 0 2 4 6 T 0 2 4 6 T
sidelobe above main beam 18 18 16 15 dB 18 18 17 16 dB 18 18 18 18 dB
11271-B
936.3740/b
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Kit for use with above mounting kits,
(optional) 011 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200
-45
17102200
+45
7-16 DIN 7-16 DIN
78.6 inches
(1996 mm)
6.1 inches
(155 mm)
76.9 inches
(1954 mm)
2.8 inches
(70 mm)
2.5 inches
(64 mm)
79.8 inches
(2026 mm)
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
06
Remote Control Option
742 213V01
Prole PF5
Vertical pattern
45- polarization
06 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
133
17102690 MHz Panel Antenna
X- polarization
General specications:
Frequency range 17102690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Electrical downtilt 06 (continously adjustable)
(manual or remote control)
Isolation, between ports >30 dB
Maximum input power 300 watts (at 50C) per input
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 65.7 x 6.1 x 2.8 inches
(1670 x 155 x 70 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 97 lbf / 26 lbf / 99 lbf
(430 N) / (115 N) / (440 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 70.9 x 6.8 x 3.6 inches
(1800 x 172 x 92 mm)
11377-A
936.4200
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 08 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102690 MHz
X - POL
Adjustable Electrical Downtilt
06
800 10651
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
06 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Specications: 17101990 MHz 19202170 MHz 21702490 MHz 24902690 MHz
Gain 18.5 dBi 19 dBi 19.4 dBi 19.5 dBi
+45 and -45 polarization 67 (half-power) 63 (half-power) 60 (half-power) 58 (half-power)
horizontal beamwidth
+45 and -45 polarization 5.4 (half-power) 4.9 (half-power) 4.3 (half-power) 4 (half-power)
vertical beamwidth
Front-to-back ratio >28 dB >28 dB >25 dB >25 dB
(18030)
Sidelobe suppression for: 0 3 6 T 0 3 6 T 0 3 6 T 0 3 6 T
First sidelobe above main beam >16 17 16 dB >17 17 16 dB >17 17 16 dB >17 17 17 dB
Cross polar ratio 0 20 dB (typical) 30 dB (typical) 30 dB (typical) 30 dB (typical)
Sector 60 >10 dB >10 dB >10 dB >10 dB
65.7 inches
(1670 mm)
68.6 inches
(1742 mm)
67.4 inches
(1712 mm)
2.5 inches
(64 mm)
2.8 inches
(70 mm)
6.1 inches
(155 mm)
45o +45o
17102690
45
17102690
+45
7-16 7-16
N
E
W
Prole PF5
Mounting Clamps Included
134
17102200 MHz Panel Antenna
X- polarization
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 20.6 dBi 21.1 dBi 21.2 dBi
+45 and -45 polarization 65 (half-power) 62 (half-power) 60 (half-power)
horizontal beamwidth
+45 and -45 polarization 3.7 (half-power) 3.5 (half-power) 3.3 (half-power)
vertical beamwidth
Front-to-back ratio (1803) >30 dB >28 dB >28 dB
Sidelobe suppression for 0 3 6 0 3 6 0 3 6
rst sidelobe above main beam >18 18 17 dB >18 17 17 dB >17 17 17 dB
First null-ll at 0 tilt 20 dB 20 dB 20 dB
Cross polar ratio
Main direction 0 25 dB (typical) 23 dB (typical) 23 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Electrical downtilt 06 degrees
continuously adjustable
Tracking, average 1.0 dB
Squint 2.5
Weight 28.7 lb (13 kg)
32.6 lb (14.8 kg) clamps included
Dimensions 100.3 x 6.1 x 3.5 inches
(2548 x 155 x 89 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 149 lbf / 59 lbf / 165 lbf
(660 N) / (260 N) / (730 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 116.9 x 6.8 x 4.4 inches
(2970 x 172 x 112 mm)
Shipping weight 34.2 lb (15.5 kg)
11026-A
936.3921
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 08 degrees downtilt angle.
Reference the Mechanical Accessories section.
65
17102200 MHz
X - POL
Adjustable Electrical Downtilt
06
800 10378
17102200
45o
17102200
+45o
7-16 7-16
6.1 inches
(155 mm)
100.3 inches
(2548 mm)
103.7 inches
(2635 mm)
3.5 inches
(89 mm)
102.6 inches
(2605 mm)
2.625 inches 0.125
(68 mm 4)
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
06 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Prole PF11
Mounting Clamps Included
135
17102200 MHz Panel Antenna with Extended Downtilt Range
XX- polarization
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
015 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-153 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Weight 37.5 lb (17 kg)
41.9 lb (19 kg) clamps included
Dimensions 54.7 x 12.7 x 2.8 inches
(1389 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 158 lbf / 36 lbf / 162 lbf
(700 N) / (160 N) / (720 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 66.4 x 13.3 x 4.4 inches
(1686 x 337 x 112 mm)
Shipping weight 46.3 lb (21 kg)
11307-A
936.3986/a
Specications: 17101880 MHz 18501990 MHz 19202170 MHz 20002200 MHz
Gain 17.5 dBi 17.6 dBi 17.7 dBi 17.8 dBi
Front-to-back ratio > 30 dB (co-polar) > 30 dB (co-polar) > 30 dB (co-polar) > 28 dB (co-polar)
(180 30)
Horizontal beamwidth 65 (half-power) 63 (half-power) 62 (half-power) 62 (half-power)
Vertical beamwidth 7.9 (half-power) 7.5 (half-power) 7.2 (half-power) 6.9 (half-power)
Electrical downtilt 015 015 015 015
continuously adjustable (manual or optional remote control)
Sidelobe suppression 0 5 10 15 T 0 5 10 15 T 0 5 10 15 T 0 5 10 15 T
rst sidelobe above main beam >17 20 18 17 dB >16 20 18 18 dB >15 19 18 17 dB >14 18 18 16 dB
within 020 sector above horizon >17 18 18 16 dB >16 17 17 16 dB >15 17 17 16 dB >14 16 16 15 dB
Cross polar ratio
Main direction 0 24 dB (typical) 24 dB (typical) 24 dB (typical) 26 dB (typical)
Sector 60 >9 dB >9 dB >10 dB >10 dB
Null-ll at 0 tilt 23 dB 22 dB 21 dB 20 dB
65
17102200 MHz
XX - POL
Adjustable Electrical Downtilt
015
Remote Control Option
800 10510V01
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 015 degrees downtilt angle.
Reference the Mechanical Accessories section.
54.7 inches
(1389 mm)
2.8 inches
(71 mm)
58.8 inches
(1494 mm)
12.7 inches
(323 mm) 3.9 inches
(98 mm)
56.5 inches
(1436 mm)
2.625 inches 0.125
(68 mm 4)
64.4 inches
(1636 mm)
17102200 Left
45o 45o
+45o
Right 17102200
+45o
RCU RCU
Layout of interface
Prole PF8
Mounting Clamps Included
136
17102200 MHz Panel Antenna with Extended Downtilt Range
XX- polarization
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-153 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Weight 39.7 lb (18 kg)
44.1 lb (20 kg) clamps included
Dimensions 78.7 x 12.7 x 2.8 inches
(1999 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 230 lbf / 52 lbf / 243 lbf
(1020 N) / (230 N) / (1080 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 90.4 x 13.3 x 4.4 inches
(2296 x 337 x 112 mm)
Shipping weight 48.5 lb (22 kg)
11337-B
936.4057/a
Specications: 17101880 MHz 18501990 MHz 19202170 MHz 20002200 MHz
Gain (dBi) 18.5 18.7 18.5 18.7 19 18.5 18.7 19 18.4 18.7 18.9 18.3
Tilt 0 5 10 0 5 10 0 5 10 0 5 10
Front-to-back ratio >
30 dB (co-polar) >
30 dB (co-polar) >
30 dB (co-polar) >
28 dB (co-polar)
(180 30)
Horizontal beamwidth 66 (half-power) 65 (half-power) 65 (half-power) 63 (half-power)
Vertical beamwidth 5 (half-power) 4.8 (half-power) 4.6 (half-power) 4.4 (half-power)
Electrical downtilt 010 010 010 010
continuously adjustable (manual or optional remote control)
Sidelobe suppression 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T
rst sidelobe above main beam >20 20 18 18 dB >20 20 18 18 dB >19 20 18 18 dB >18 20 18 18 dB
within 020 sector above horizon >18 18 17 17 dB >17 18 17 15 dB >17 17 17 15 dB >17 17 14 12 dB
Cross polar ratio
Main direction 0 22 dB (typical) 22 dB (typical) 22 dB (typical) 22 dB (typical)
Sector 60 >10 dB >10 dB >10 dB >10 dB
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 010 degrees downtilt angle.
Reference the Mechanical Accessories section.
78.7 inches
(1999 mm)
2.8 inches
(71 mm)
82.8 inches
(2104 mm)
12.7 inches
(323 mm)
3.9 inches
(98 mm)
81.3 inches
(2064 mm)
2.625 inches 0.125
(68 mm 4)
Vertical pattern
45- polarization
010 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
65
17102200 MHz
XX - POL
Adjustable Electrical Downtilt
010
Remote Control Option
800 10511V01
Prole PF8
Mounting Clamps Included
137
17102170 MHz Panel Antenna
X Polarization
Vertical pattern
45- polarization
010 electrical downtilt
Horizontal pattern
45- polarization
Mounting Equipment:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
732 327 Tilt Kit for use with the above
(optional) mounting kits,
020 degrees downtilt angle.
Reference the Mechanical Accessories section.
General specications:
Frequency range 17102170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >25 dB (co-polar)
>25 dB (total power)
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking 0.5 dB
Squint 3.5
Weight 9.3 lb (4.2 kg)
Dimensions 26.1 x 6.1 x 2.7 inches
(662 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 40 lbf / 15 lbf / 45 lbf
(175 N) / (65 N) / (200 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 36.8 x 6.8 x 3.6 inches
(935 x 172 x 92 mm)
Shipping weight 12 lb (5.5 kg)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 13.7 dBi 14 dBi 14.1 dBi
Horizontal beamwidth 88 (half-power) 88 (half-power) 88 (half-power)
Vertical beamwidth 14.7 (half-power) 14 (half-power) 13 (half-power)
Electrical downtilt 010 010 010
continuously adjustable (manual or optional remote control)
Sidelobe suppression for 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T
rst sidelobe above horizon 18 18 18 18 dB 18 18 18 18 dB 18 18 18 18 dB
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
11283-A
936.3957/a
17102170
-45
17102170
+45
7-16 DIN 7-16 DIN
88
17102170 MHz
X - POL
Adjustable Electrical Downtilt
010
Remote Control Option
741 988V01
Prole PF5
26.1 inches
(662 mm)
2.5 inches
(68 mm)
29.3 inches
(746 mm)
28.2 inches
(716 mm)
6.1 inches
(155 mm)
2.7 inches
(69 mm)
Mounting Clamps Included
138
17102200 MHz Panel Antenna
X Polarization
17102200
-45
17102200
+45
7-16 DIN 7-16 DIN
General specications:
Frequency range 17102200 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 08 degrees
continuously adjustable
Connector 2 x 7-16 DIN female
Isolation >30 dB
Tracking 0.5 dB
Squint 2.0
Weight 16.5 lb (7.5 kg)
20.9 lb (9.5 kg) clamps included
Dimensions 51.3 x 6.1 x 2.7 inches
(1302 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 79 lbf / 29 lbf / 90 lbf
(350 N) / (125 N) / (400 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 62 x 6.8 x 3.6 inches
(1574 x 172 x 92 mm)
Shipping weight 25.4 lb (11.5 kg)
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
08 electrical downtilt
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 010 degrees downtilt angle.
Reference the Mechanical Accessories section.
11268-A
936.3843/a
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 16.5 dBi 16.8 dBi 16.7 dBi
45 polarization 88 (half-power) 88 (half-power) 88 (half-power)
horizontal beamwidth
45 polarization 7 (half-power) 6.7 (half-power) 6.5 (half-power)
vertical beamwidth
Sidelobe suppression
for rst sidelobe 0 2 5 8 T 0 2 5 8 T 0 2 5 8 T
above main beam 18 18 16 14 dB 20 20 18 17 dB 18 18 18 17 dB
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
Front-to-back ratio >25 dB (co-polar) >25 dB (co-polar) >24 dB (co-polar)
(18030) >25 dB (total power) >25 dB (total power) >24 dB (total power)
53.4 inches
(1356 mm)
51.3 inches
(1302 mm)
2.5 inches
(68 mm 4)
54.6 inches
(1386 mm)
88
17102200 MHz
X - POL
Adjustable Electrical Downtilt
08
Remote Control Option
741 989V01
Prole PF5
6.1 inches
(155 mm)
2.7 inches
(69 mm)
Mounting Clamps Included
139
17102170 MHz Panel Antenna
X Polarization
Vertical pattern
45- polarization
06 electrical downtilt
Horizontal pattern
45- polarization
78.6 inches
(1996 mm)
76.5 inches
(1942 mm)
2.5 inches
(68 mm 4)
79.8 inches
(2026 mm)
17102170
-45
17102170
+45
7-16 DIN 7-16 DIN
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 17.7 dBi 18 dBi 18.2 dBi
+45 and -45 polarization 88 (half-power) 88 (half-power) 88 (half-power)
horizontal beamwidth
+45 and -45 polarization 4.9 (half-power) 4.7 (half-power) 4.5 (half-power)
vertical beamwidth
Sidelobe suppression for rst 0 2 4 6 T 0 2 4 6 T 0 2 4 6 T
sidelobe above main beam 17 17 17 17 dB 18 18 18 18 dB 18 18 18 18 dB
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >25 dB (co-polar)
>25 dB (total power)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 06 degrees
continuously adjustable (manual or optional remote control)
Connector 2 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 20 dB (typical)
Sector 60 >10 dB
Tracking 0.5 dB
Squint 2.5
Weight 24.3 lb (11 kg)
28.7 lb (13.kg) clamps included
Dimensions 76.5 x 6.1 x 2.7 inches (1942 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 115 lbf / 42 lbf / 138 lbf
(510 N) / (185 N) / (610 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 87.2 x 6.8 x 3.6 inches (2214 x 172 x 92 mm)
Shipping weight 30.9 lb (14 kg)
11284-A
936.3926/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 011 degrees downtilt angle.
Reference the Mechanical Accessories section.
88
17102170 MHz
X - POL
Adjustable Electrical Downtilt
06
Remote Control Option
741 990V01
Prole PF5
6.1 inches
(155 mm)
2.7 inches
(69 mm)
Mounting Clamps Included
140
17102170 MHz Panel Antenna
XX- polarization
General specications:
Frequency range 17102170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Front-to-back ratio >25 dB (co-polar)
>25 dB (total power)
Connector 4 x 7-16 DIN female
Isolation >30 dB
Maximum input power 250 watts (at 50C) per input
Weight 24.3 lb (11 kg)
28.7 lb (13 kg) clamps included
Dimensions 26.8 x 12.7 x 2.8 inches
(679 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 79 lbf / 20 lbf / 84 lbf
(350 N) / (85 N) / (370 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 36.4 x 14.2 x 5.1 inches
(924 x 360 x 130 mm)
Shipping weight 30.9 lb (14 kg)
11291-A
936.3985/a
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 054 degrees downtilt angle.
Reference the Mechanical Accessories section.
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 15 dBi 15.2 dBi 15.3 dBi
Horizontal beamwidth 67 (half-power) 65 (half-power) 62 (half-power)
Vertical beamwidth 14 (half-power) 13.7 (half-power) 13 (half-power)
Electrical downtilt 010 010 010
continuously adjustable (manual or optional remote control)
Sidelobe suppression for rst 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T
sidelobe above main beam 16 16 15 15 dB 16 16 16 16 dB 16 16 16 16 dB
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 10 dB (typical) 10 dB (typical) 10 dB (typical)
17102170 Left
45o 45o
+45o
Right 17102170
+45o
RCU RCU
Layout of interface
26.8 inches
(679 mm)
2.8 inches
(71 mm)
35 inches
(889 mm)
3.9 inches
(98 mm)
12.7 inches
(323 mm)
29.3 inches
(744 mm)
2.625 inches 0.125
(68 mm 4)
742 233V01
65
17102170 MHz
17102170 MHz
XX-POL
Adjustable Electrical Downtilt
010
Remote Control Option
Prole PF8
Mounting Clamps Included
141
17102170 MHz Panel Antenna
XX- polarization
11293-C
936.4021/d
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
Maximum input power 250 watts per input (at 50C)
Electrical downtilt 08 degrees
continuously adjustable (manual or optional remote control)
Connector 4 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Weight 27.6 lb (12.5 kg)
32 lb (14.5 kg) clamps included
Dimensions 45.2 x 12.7 x 2.8 inches (1147 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 133 lbf / 31 lbf / 138 lbf
(590 N) / (135 N) / (610 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 56.9 x 13.3 x 4.1 inches (1446 x 337 x 104 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 17.5 dBi 17.7 dBi 18 dBi
+45 and -45 polarization 65 (half-power) 63 (half-power) 61 (half-power)
horizontal beamwidth
+45 and -45 polarization 8.3 (half-power) 8 (half-power) 7.5 (half-power)
vertical beamwidth
Sidelobe suppression for rst 0 4 8 T 0 4 8 T 0 4 8 T
sidelobe above main beam 20 20 18 dB 20 20 18 dB 20 20 18 dB
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 018 degrees downtilt angle.
Reference the Mechanical Accessories section.
2.8 inches
(71 mm)
12.7 inches
(323 mm)
53.4 inches
(1357 mm)
45.2 inches
(1147 mm)
47.7 inches
(1212 mm)
2.625 inches 0.125
(68 mm 4)
3.9 inches
(98 mm)
742 237
65
17102170 MHz
17102170 MHz
XX-POL
Adjustable Electrical Downtilt
08
Remote Control Option
Prole PF8
17102170 Left
45o 45o
+45o
Right 17102170
+45o
RCU RCU
Layout of interface
Vertical pattern
45- polarization
08 electrical downtilt
Horizontal pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
N
E
W
142
17102200 MHz Panel Antenna
XX- polarization
11273-B
936.3781/a
General specications:
Frequency range 17102200 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
>25 dB (total power)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 010 degrees
continuously adjustable (manual or optional remote control)
Connector 4 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Weight 33.1 lb (15 kg)
37.5 lb (17 kg) clamps included
Dimensions 51.9 x 12.7 x 2.8 inches (1319 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 149 lbf / 35 lbf / 156 lbf
(660 N) / (155 N) / (690 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 62 x 14.2 x 5.1 inches (1574 x 360 x 130 mm)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.6 dBi 17.8 dBi 18 dBi
+45 and -45 polarization 64 (half-power) 64 (half-power) 62 (half-power)
horizontal beamwidth
+45 and -45 polarization 7 (half-power) 6.8 (half-power) 6.5 (half-power)
vertical beamwidth
Sidelobe suppression for rst 0 5 10 T 0 5 10 T 0 5 10 T
sidelobe above main beam 20 18 16 dB 20 18 16 dB 16 18 16 dB
Vertical pattern
45- polarization
010 electrical
Horizontal pattern
45- polarization
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
2.8 inches
(71 mm)
12.7 inches
(323 mm)
60.2 inches
(1529 mm)
51.9 inches
(1319 mm)
54.5 inches
(1384 mm)
2.625 inches 0.125
(68 mm 4)
3.9 inches
(98 mm)
742 236V01
65
17102200 MHz
17102200 MHz
XX-POL
Adjustable Electrical Downtilt
010
Remote Control Option
Prole PF8
17102200 Left
45o 45o
+45o
Right 17102200
+45o
RCU RCU
Layout of interface
Mounting Clamps Included
143
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 011 degrees downtilt angle.
Reference the Mechanical Accessories section.
Vertical pattern
45- polarization
06 electrical downtilt
Horizontal pattern
45- polarization
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 19 dBi 19.2 dBi 19.5 dBi
Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) >30 dB (co-polar)
>25 dB (total power) >25 dB (total power) >24 dB (total power)
Horizontal beamwidth 65 (half-power) 64 (half-power) 63 (half-power)
Vertical beamwidth 4.6 (half-power) 4.4 (half-power) 4.2 (half-power)
Electrical downtilt 06 06 06
continuously adjustable (manual or optional remote control)
Vertical Pattern Sidelobe 0 2 4 6 T 0 2 4 6 T 0 2 4 6 T
suppression for rst 17 17 14 14 dB 17 17 15 15 dB 17 17 15 15 dB
sidelobe above main beam
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
General specications:
Frequency range 17102170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 4 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 0.5 dB
Squint 2.5
Weight 39.7 lb (18 kg)
44.1 lb (20 kg) clamps included
Dimensions 77.1 x 12.7 x 2.8 inches
(1959 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 228 lbf / 50 lbf / 234 lbf
(1010 N) / (220 N) / (1040 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 93.9 x 14.2 x 5.1 inches
(2384 x 360 x 130 mm)
Shipping weight 48.5 lb (22 kg)
1710-2170 Left
-45o -45o
+45o
Right 1710-2170
+45o
RCU RCU
Layout of interface
11292-B
936.3993/a
17102170 MHz Panel Antenna
XX- polarization
2.8 inches
(71 mm)
3.9 inches
(98 mm)
12.7 inches
(323 mm)
85.4 inches
(2169 mm)
79.7 inches
(2024 mm)
2.625 inches 0.125
(68 mm 4)
77.1 inches
(1959 mm)
742 235V01
65
17102170 MHz
17102170 MHz
XX-POL
Adjustable Electrical Downtilt
06
Remote Control Option
Prole PF8
Mounting Clamps Included
144
General specications:
Frequency range 17102180 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3:< -150dBc
Polarization +45 and -45
Front-to-back ratio >24 dB (co-polar)
>24 dB (total power)
Maximum input power 300 watts per input (at 50C)
Electrical downtilt 010 degrees
continuously adjustable
Connector 4 x 7-16 DIN female
Isolation intrasystem >30 dB
intersystem >30 dB
Tracking 0.5 dB
Squint 2.5
Weight 37.5 lb (17 kg)
41.9 lb (19 kg) clamps included
Dimensions 51.9 x 12.7 x 2.8 inches
(1319 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 149 lbf / 35 lbf / 156 lbf
(660 N) / (155 N) / (690 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 62 x 14.2 x 5.1 inches
(1574 x 360 x 130 mm)
Shipping weight 43 lb (19.5 kg)
Specications: 17101880 MHz 18501990 MHz 19202180 MHz
Average gain (dBi) 0 5 10 T 0 5 10 T 0 5 10 T
16.1 16.3 16 16.2 16.4 16.1 16.5 16.7 16.2
+45 and -45 polarization 88 (half-power) 90 (half-power) 88 (half-power)
horizontal beamwidth
+45 and -45 polarization 7.4 (half-power) 7 (half-power) 6.5 (half-power)
vertical beamwidth
Electrical downtilt 010 010 010
continuously adjustable
(manual or optional remote control)
Vertical Pattern Sidelobe 0 4 8 10 T 0 4 8 10 T 0 4 8 10 T
suppression for rst 18 17 16 15 dB 18 17 16 15 dB 17 17 16 15 dB
sidelobe above main beam
Cross polar ratio (typical)
Main direction 0 15 dB 15 dB 15 dB
Sector 60 >8 dB >7.5 dB >7 dB
11281-B
936.3948/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
1710-2180 Left
-45o -45o
+45o
Right 1710-2180
+45o
RCU RCU
Layout of interface
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
o
0
0
3
o
0
3
3
o
3
10
20
30
17102180 MHz Panel Antenna
XX- polarization
12.7 inches
(323 mm)
60.2 inches
(1529 mm)
51.9 inches
(1319 mm)
54.5 inches
(1384 mm)
2.8 inches
(71 mm)
2.625 inches 0.125
(68 mm 4)
3.9 inches
(98 mm)
742 352V01
88
17102180 MHz
17102180 MHz
XX-POL
Adjustable Electrical Downtilt
010
Remote Control Option
Prole PF8
Mounting Clamps Included
145
17102170 MHz Panel Antenna
X- polarization
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 8.5 dBi 8.6 dBi 8.7 dBi
Front-to-back ratio >25 dB (co-polar) >30 dB (co-polar) >30 dB (co-polar)
+45 and -45 polarization 70 (half-power) 68 (half-power) 65 (half-power)
horizontal beamwidth
+45 and -45 polarization 65 (half-power) 65 (half-power) 63 (half-power)
vertical beamwidth
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
7-16 DIN 7-16 DIN
1710-2170
-45
1710-2170
+45
Mounting Equipment:
Model Description
734 365 Mounting Kit for 1.8 to 4.9 inch
(45 to 125 mm) OD mast.
Reference the Mechanical Accessories section.
11288-B
936.3969/a
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.4:1
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Maximum input power 150 watts per input (at 50C)
Connector 2 x 7-16 DIN female
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Isolation >30 dB
Tracking, average 1 dB
Squint 3
Weight 3.3 lb (1.5 kg)
Dimensions 6.1 x 6.1 x 2.7 inches (155 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 12 lbf / 3 lbf / 13 lbf
(50 N) / (13 N) / (55 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 10.1 x 6.8 x 3.6 inches (257 x 172 x 92 mm)
Shipping weight 4.4 lb (2 kg)
6.1 inches
(155 mm)
9.4 inches
(239 mm)
2.7 inches
(69 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
8.2 inches
(209 mm)
68
17102170 MHz
X - POL
0 Electrical Downtilt
742 210V01
Prole PF5
Mounting Clamps Included
146
17102170 MHz Panel Antenna
X- polarization
11268-A
936.3862/a
General specications:
Frequency range 17102170 MHz
VSWR <1.4:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 150 watts (at 50C) per input
Tracking 0.5 dB
Squint 1.5
Weight 4.9 lb (2.2 kg)
Dimensions 13.5 x 6.1 x 2.7 inches
(342 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 21 lbf / 7 lbf / 24 lbf
(90 N) / (27 N) / (105 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 17.5 x 6.8 x 3.6 inches
(444 x 172 x 92 mm)
Shipping weight 7.1 lb (3.2 kg)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 11.5 dBi 12 dBi 12 dBi
+45 and -45 polarization 67 (half-power) 65 (half-power) 63 (half-power)
horizontal beamwidth
+45 and -45 polarization 32 (half-power) 30 (half-power) 28 (half-power)
vertical beamwidth
Electrical downtilt 3 2 0
Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) >27 dB (co-polar)
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
7-16 DIN 7-16 DIN
1710-2170
-45
1710-2170
+45
Mounting Equipment:
Model Description
734 365 Mounting Kit for 1.8 to 4.9 inch
(45 to 125 mm) OD mast.
732 327 Tilt Kit for use with the above
(optional) mounting kits,
036 degrees downtilt angle.
Reference the Mechanical Accessories section.
13.5 inches
(342 mm)
16.8 inches
(426 mm)
15.6 inches
(396 mm)
2.7 inches
(69 mm)
6.1 inches
(155 mm)
2.5 inches
(64 mm)
65
17102170 MHz
X - POL
2 Electrical Downtilt
739 489V01
Prole PF5
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
2 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
147
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.4:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Maximum input power 300 watts per input (at 50C)
Connector 2 x 7-16 DIN female
Isolation >30 dB
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >10 dB
Tracking, average 0.5 dB
Squint 1.5
Weight 9.9 lb (4.5 kg)
Dimensions 28.9 x 6.1 x 2.7 inches (735 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 42 lbf / 15 lbf / 50 lbf
(185 N) / (65 N) / (220 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 39.4 x 6.8 x 3.7 inches (1000 x 172 x 95 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 15.3 dBi 15.6 dBi 15.8 dBi
Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) >30 dB (co-polar)
(180 30) >25 dB (total power) >25 dB (total power) >25 dB (total power)
+45 and -45 polarization 67 (half-power) 66 (half-power) 64 (half-power)
horizontal beamwidth
+45 and -45 polarization 12.6 (half-power) 11.8 (half-power) 11 (half-power)
vertical beamwidth
Sidelobe suppression for >14 dB >16 dB >14 dB
rst sidelobe above horizon
11287-A
936.3968/a
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
1710-2170
-45
7-16
1710-2170
+45
7-16
-45o +45o
6.1 inches
(155 mm)
32.2 inches
(819 mm)
28.9 inches
(735 mm)
2.7 inches
(69 mm)
31.1 inches
(789 mm)
2.5 inches
(64 mm)
Mounting Equipment:
Model Description
734 365 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(optional) (50 to 115 mm) OD mast.
850 10013 Tilt Kit for use with above mounting kit
(optional) 050 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102170 MHz Panel Antenna
X- polarization
65
17102170 MHz
X - POL
0 Electrical Downtilt
742 196V01
Prole PF5
Mounting Clamps Included
148
General specications:
Frequency range 17102200 MHz
VSWR <1.4:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 0.5 dB
Squint 1.5
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 51.3 x 6.1 x 2.7 inches
(1302 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 26 lbf / 88 lbf
(330 N) / (115 N) / (390 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 56.9 x 6.8 x 3.6 inches
(1445 x 172 x 92 mm)
Shipping weight 22.5 lb (10.2 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.9 dBi 18.1 dBi 18.3 dBi
+45 and -45 polarization 67 (half-power) 66 (half-power) 64 (half-power)
horizontal beamwidth
+45 and -45 polarization 6.6 (half-power) 6.2 (half-power) 5.8 (half-power)
vertical beamwidth
Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) >30 dB (co-polar)
Sidelobe suppression for >14 dB >15 dB >16 dB
rst sidelobe above main beam
First null-ll 25 dB (typical) 25 dB (typical) 25 dB (typical)
below main beam
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
11269-A
936.3818/a
51.3 inches
(1302 mm)
54.6 inches
(1386 mm)
2.7 inches
(69 mm)
53.4 inches
(1356 mm)
2.5 inches
(64 mm)
45o +45o
6.1 inches
(155 mm)
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200 MHz Panel Antenna
X- polarization
65
17102200 MHz
X - POL
0 Electrical Downtilt
800 10425V01
Prole PF5
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
17102200
45o
17102200
+45o
7-16 7-16
Mounting Clamps Included
149
General specications:
Frequency range 17102200 MHz
VSWR <1.4:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Electrical downtilt 2 degrees
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 0.5 dB
Squint 1.5
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 51.3 x 6.1 x 2.7 inches
(1302 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 26 lbf / 88 lbf
(330 N) / (115 N) / (390 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 56.9 x 6.8 x 3.6 inches
(1445 x 172 x 92 mm)
Shipping weight 22 lb (10 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.9 dBi 18.1 dBi 18.3 dBi
+45 and -45 polarization 66 (half-power) 65 (half-power) 63 (half-power)
horizontal beamwidth
+45 and -45 polarization 6.6 (half-power) 6.2 (half-power) 5.8 (half-power)
vertical beamwidth
Front-to-back ratio >28 dB (co-polar) >30 dB (co-polar) >33 dB (co-polar)
Sidelobe suppression for >14 dB >15 dB >15 dB
rst sidelobe above main beam
First null-ll 25 dB (typical) 25 dB (typical) 25 dB (typical)
below main beam
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
2 electrical downtilt
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
7-16 DIN 7-16 DIN
1710/2200
-45
1710/2200
+45
11303-A
936.3983/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200 MHz Panel Antenna
X- polarization
51.3 inches
(1302 mm)
54.6 inches
(1386 mm)
2.7 inches
(69 mm)
53.4 inches
(1356 mm)
2.5 inches
(64 mm)
45o +45o
6.1 inches
(155 mm)
65
17102200 MHz
X - POL
2 Electrical Downtilt
800 10426V01
Prole PF5
Mounting Clamps Included
150
General specications:
Frequency range 17102200 MHz
VSWR <1.3:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: < -150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Electrical downtilt 6 degrees
Isolation >30 dB
Maximum input power 300 watts (at 50C) per input
Tracking, average 0.5 dB
Squint 1.5
Weight 15.4 lb (7 kg)
19.8 lb (9 kg) clamps included
Dimensions 51.3 x 6.1 x 2.7 inches
(1302 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 75 lbf / 26 lbf / 88 lbf
(330 N) / (115 N) / (390 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 56.9 x 6.8 x 3.6 inches
(1445 x 172 x 92 mm)
Shipping weight 22 lb (10 kg)
Specications: 17101880 MHz 18501990 MHz 19202200 MHz
Gain 17.7 dBi 17.9 dBi 18.1 dBi
+45 and -45 polarization 67 (half-power) 65 (half-power) 63 (half-power)
horizontal beamwidth
+45 and -45 polarization 6.7 (half-power) 6.3 (half-power) 5.8 (half-power)
vertical beamwidth
Front-to-back ratio >27 dB (co-polar) >33 dB (co-polar) >33 dB (co-polar)
Sidelobe suppression for >14 dB >14 dB >15 dB
rst sidelobe above main beam
First null-ll 25 dB (typical) 25 dB (typical) 25 dB (typical)
below main beam
Cross polar ratio
Main direction 0 25 dB (typical) 25 dB (typical) 25 dB (typical)
Sector 60 >10 dB >10 dB >10 dB
Horizontal pattern
45- polarization
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
Vertical pattern
45- polarization
6 electrical downtilt
11304-A
936.4036/a
7-16 DIN 7-16 DIN
1710/2200
-45
1710/2200
+45
51.3 inches
(1302 mm)
54.6 inches
(1386 mm)
2.7 inches
(69 mm)
53.4 inches
(1356 mm)
2.5 inches
(64 mm)
45o +45o
6.1 inches
(155 mm)
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 016 degrees downtilt angle.
Reference the Mechanical Accessories section.
17102200 MHz Panel Antenna
X- polarization
65
17102200 MHz
X - POL
6 Electrical Downtilt
800 10428V01
Prole PF5
Mounting Clamps Included
151
17102170 MHz Panel Antenna
X- polarization
11285-A
936.3937/a
General specications:
Frequency range 17102170 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Maximum input power 300 watts per input (at 50C)
Connector 2 x 7-16 DIN female
Cross polar ratio
Main direction 0 25 dB (typical)
Sector 60 >14 dB
Isolation >30 dB
Tracking 0.5 dB
Aquint 1
Weight 20.9 lb (9.5 kg)
25.4 lb (11.5.kg) clamps included
Dimensions 85 x 6.1 x 2.7 inches (2160 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 131 lbf / 45 lbf / 151 lbf
(580 N) / (200 N) / (670 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 89.4 x 6.8 x 3.6 inches (2304 x 172 x 92 mm)
Shipping weight 29.5 lb (13.4 kg)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 20 dBi 20.2 dBi 20.5 dBi
Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) >30 dB (co-polar)
(180 30) >28 dB (total power) >28 dB (total power) >27 dB (total power)
+45 and -45 polarization 67 (half-power) 65 (half-power) 61 (half-power)
horizontal beamwidth
+45 and -45 polarization 4 (half-power) 3.8 (half-power) 3.5 (half-power)
vertical beamwidth
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
0o
0
3
o
0
6
o
90o
0
2
1
o
0
5
1
o
180o
0
1
2
o
0
4
2
o
270o
0
0
3
o
0
3
3
o
3
10
20
30
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 010 degrees downtilt angle.
Reference the Mechanical Accessories section.
1710-2170
-45
1710-2170
+45
7-16 DIN 7-16 DIN
85 inches
(2160 mm)
2.7 inches
(69 mm)
6.1 inches
(155 mm)
88.3 inches
(2244 mm)
87.2 inches
(2214 mm)
2.5 inches
(64 mm)
65
17102170 MHz
X - POL
0 Electrical Downtilt
742 186V01
Prole PF5
Mounting Clamps Included
152
17102200 MHz Panel Antenna
X Polarization
General specications:
Frequency range 17102200 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Connector 2 x 7-16 DIN female
Isolation, between ports >30 dB
Maximum input power 300 watts (at 50C) per input
Sidelobe suppression for
rst sidelobe above main beam >15 dB
0 30 sector above horizon >15 dB
First null-ll below main beam < 20 dB
Tracking, average 0.5 dB
Squint 1.0
Weight 25.4 lb (11.5 kg)
29.8 lb (13.5 kg) clamps included
Dimensions 85.5 x 6.1 x 3.5 inches
(2172 x 155 x 89 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 124 lbf / 48 lbf / 138 lbf
(550 N) / (210 N) / (610 N)
Mounting category M (Medium)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 92.1 x 6.8 x 4.8 inches
(2340 x 172 x 122 mm)
Shipping weight 34.2 lb (15.5 kg)
11270-A
936.3815/a
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Mount Kit
(optional) 09 degrees downtilt angle.
Reference the Mechanical Accessories section.
6.1 inches
(155 mm)
89.6 inches
(2276 mm)
3.5 inches
(89 mm)
88.4 inches
(2246 mm)
2.625 inches 0.125
(68 mm 4)
85.5 inches
(2172 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz 20002200 MHz
Gain 20.5 dBi 20.8 dBi 21.1 dBi 21.2 dBi
+45 and -45 polarization 66 (half-power) 63 (half-power) 60 (half-power) 58 (half-power)
horizontal beamwidth
+45 and -45 polarization 4.2 (half-power) 4 (half-power) 3.7 (half-power) 3.5 (half-power)
vertical beamwidth
Front-to-back ratio >30 dB >30 dB >30 dB >30 dB
(18030)
Cross polar ratio
Main direction 0 25 dB 23 dB 23 dB 23 dB
Sector 60 >12 dB >12 dB >10 dB >10 dB
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
65
17102200 MHz
X - POL
0 Electrical Downtilt
800 10439V01
Prole PF9
Mounting Clamps Included
153
17102170 MHz Panel Antenna
X- polarization
Mounting Equipment:
Model Description
734 365 Mounting Kit for 1.8 to 4.9 inch
(45 to 125 mm) OD mast.
Reference the Mechanical Accessories section.
General specications:
Frequency range 17102170 MHz
VSWR <1.4:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45 and -45
Front-to-back ratio >23 dB (co-polar)
(180 30) >23 dB (total power)
Connector 2 x 7-16 DIN female
Isolation >30 dB
Maximum input power 150 watts (at 50C) per input
Tracking 0.5 dB
Squint 3
Weight 4.4 lb (2 kg)
Dimensions 13.5 x 6.1 x 2.7 inches
(342 x 155 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 21 lbf / 7 lbf / 24 lbf
(90 N) / (27 N) / (105 N)
Mounting category L (Light)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 17.5 x 6.8 x 3.6 inches
(444 x 172 x 92 mm)
Shipping weight 6.6 lb (3 kg)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain 11.3 dBi 11.5 dBi 11.6 dBi
+45 and -45 polarization 86 (half-power) 87 (half-power) 88 (half-power)
horizontal beamwidth
+45 and -45 polarization 28 (half-power) 26 (half-power) 26 (half-power)
vertical beamwidth
Sidelobe suppression
vertical sector 45 >20 dB >20 dB >20 dB
Cross polar ratio
Main direction 0 20 dB (typical) 25 dB (typical) 20 dB (typical)
Sector 60 >18 dB >18 dB >15 dB
11282-A
936.3938/a
13.5 inches
(342 mm)
16.8 inches
(426 mm)
2.7 inches
(69 mm)
2.5 inches
(64 mm)
6.1 inches
(155 mm)
15.6 inches
(396 mm)
88
17102170 MHz
X - POL
0 Electrical Downtilt
741 984V01
Prole PF5
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
17102170
45o
17102170
+45o
7-16 7-16
Mounting Clamps Included
154
17102180 MHz Panel Antenna
V- polarization
800 10368
13
17102180 MHz
V - POL
Mounting Equipment:
Model Description
2 X 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
Reference the Mechanical Accessories section.
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
H-plane
Horizontal pattern
V- polarization
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
E-plane
Vertical pattern
V- polarization
Specications: 17101880 MHz 18501990 MHz 19202180 MHz
Average gain 18.1 dBi 18.4 dBi 18.7 dBi
H-plane beamwidth 13.3 (half-power) 12.8 (half-power) 12 (half-power)
Sidelobe suppression >18 dB >18 dB >17 dB
horizontal pattern
E-plane beamwidth 37 (half-power) 36 (half-power) 36 (half-power)
Sidelobe suppression for >18 dB >18 dB >18 dB
rst sidelobe above main beam
vertical pattern
General specications:
Frequency range 17102180 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3:< -150dBc
Polarization Vertical
Front-to-back ratio >30 dB (co-polar)
(180 30)
Maximum input power 300 watts per input (at 50C)
Connector 7-16 DIN female
Weight 19.8 lb (9 kg)
Dimensions 29.3 x 11.8 x 3 inches
(743 x 299 x 69 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 77 lbf / 6 lbf / 90 lbf
(340 N) 6 (25 N) / (400 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 33.5 x 17.4 x 4.9 inches
(852 x 442 x 124 mm)
10908-B
936.2945/b
11.8 inches
(299 mm)
3 inches
(77 mm)
29.3 inches
(743 mm)
155
24962690 MHz Panel Antenna
X Polarization
11097-A
42 inches
(1067 mm)
45.3 inches
(1151 mm)
44.1 inches
(1120 mm)
2.7 inches
(69 mm)
2.5 inches
(64 mm )
6.1 inches
(155 mm)
48
24962690 MHz
X - POL
Adjustable Electrical Downtilt
010
Remote Control Option
840 10046
Prole PF5
Mounting Equipment:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Kit
for use with the 2 x 738 546 mounting kit
015 degrees downtilt angle.
Reference the Mechanical Accessories section.
Specications:
Frequency range 24962690 MHz
Gain 18 dBi
Impedance 50 ohms
VSWR < 1.43:1
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Front-to-back ratio >27 dB typical
Maximum input power 300 watts (at 50C)
+45 and -45 polarization 48 degrees at midband (half power)
horizontal beamwidth
+45 and -45 polarization 7 degrees at midband (half power)
vertical beamwidth
Electrical downtilt 010 degrees
continously adjustable
Connector 2 x 7-16 DIN female
Sidelobe suppression for 0 4 8 10
rst sidelobe above horizon 15 15 15 15 dB (typical)
Cross polar ratio 25 dB typical bore sight
15 dB typical 45 sector edges
Null ll > -1 dBi to 12 below horizon (typical)
Isolation >30 dB
Weight 10 lb (4.5 kg)
Dimensions 42 x 6.1 x 2.7 inches
(1067 x 155 x 69 mm)
Equivalent at plate area 2.5 ft
2
(0.23 m
2
)
Wind survival rating 150 mph (240 kph)
Shipping dimensions 48 x 6.8 x 3.6 inches
(1220 x 172 x 92 mm)
Shipping weight 13.6 lb (6.2 kg)
Mounting Fixed and tilt-mount options are
available for 2 to 5.7 inch
(50 to 145 mm) OD masts.
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
156
Designed for MIMO applications,
a single adjustment mechanism
controls the left and right antennas
simultaneously through the
010 downtilt range.
11210-C
Specications:
Frequency range 24962690 MHz
Gain 2 x 16 dBi
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Front-to-back ratio >23 dB typical
Maximum input power 300 watts (at 50C)
+45 and -45 polarization 87 degrees at midband (half power)
horizontal beamwidth
+45 and -45 polarization 7 degrees at midband (half power)
vertical beamwidth
Electrical downtilt 010 degrees
continously adjustable
Connector 4 x 7-16 DIN female
Sidelobe suppression for 0 4 8 10
rst sidelobe above horizon 15 15 15 15 dB (typical)
Cross polar ratio 15 dB typical bore sight
10 dB typical 60 sector edges
Null ll > -1 dBi to 12 below horizon (typical)
Isolation >30 dB
Weight 30 lb (13.6 kg)
Dimensions 42 x 12.7 x 2.8 inches
(1067 x 323 x 71 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 113 lbf / 21 lbf / 117 lbf
(500 N) / (90 N) / (520 N)
Wind survival rating 150 mph (240 kph)
Shipping dimensions 48 x 13.3 x 5.1 inches
(1220 x 337 x 130 mm)
Shipping weight 34 lb (15.4 kg)
24962690 MHz Panel Antenna
XX Polarization
87
24962690 MHz
XX - POL
Adjustable Electrical Downtilt
010
Remote Control Option
840 10054B
Mounting Equipment:
Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch
(50 to 115 mm) OD mast.
850 10013 Tilt Kit for use with the
2 x 738 546 mounting kit
015 degrees downtilt angle.
Reference the Mechanical Accessories section.
42 inches
(1067 mm)
45.3 inches
(1151 mm)
2.8 inches
(71 mm)
44.1 inches
(1120 mm)
2.625 inches 0.125
(68 mm 4)
12.7 inches
(323 mm)
Horizontal pattern
45- polarization
0 electrical downtilt
Vertical pattern
45- polarization
0 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Horizontal pattern
45- polarization
5 electrical downtilt
Vertical pattern
45- polarization
5 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Horizontal pattern
45- polarization
10 electrical downtilt
Vertical pattern
45- polarization
10 electrical downtilt
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Adjusts left and right
simultaneously.
24962690 Left
45o 45o
+45o
Right 24962690
+45o
RCU
Layout of interface
Prole PF8
157
17102170 MHz Trisector Antenna
X Polarization
General specications:
Frequency range 17102170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Front-to-back ratio >27 dB (co-polar)
Connector 3 x 2 x 7/16 DIN female
Maximum input power 250 watts (at 50C) per input
Weight 70.5 lb (32 kg)
Height 48.9 inches (1241 mm)
Radome diameter 9.1 inches (230 mm)
Wind load at 93 mph (150kph)
Side 47 lbf (205 N)
Wind survival rating 120 mph (200 kph)
Natural frequency 4547 Hz
Damping ratio 0.032
Shipping dimensions 54.9 x 12.4 x 13 inches
(1395 x 315 x 330 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Gain (dBi) 15.4 15.2 15 14.8 15.5 15.4 15.3 14.9 15.7 15.6 15.4 14.9
Tilt 0 4 8 12 0 4 8 12 0 4 8 12
+45 and -45 polarization 67 (half-power) 65 (half-power) 62 (half-power)
horizontal beamwidth
+45 and -45 polarization 12.7 (half-power) 12 (half-power) 11.2 (half-power)
vertical beamwidth
Electrical downtilt 012 012 012
continuously adjustable (manual or optional remote control)
Sidelobe suppression for 0 4 8 12 0 4 8 12 0 4 8 12
rst sidelobe above horizon 16 16 15 15 dB 18 17 17 16 dB 18 18 16 16
dB
Cross polar ratio
Main direction 0 20 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB (typical) >10 dB (typical) >10 dB (typical)
Isolation intrasystem >30 dB >30 dB >30 dB
intersystem >40 dB >40 dB >40 dB
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
012 electrical downtilt
10945-C
936.2830/a
65
17102170 MHz
X - POL
Adjustable Electrical Downtilt
012
Remote Control Option
800 10375
7-16
120o 240o
0o
1710 -2170 1710 -2170
1710 -2170
7-16
7-16 7-16
7-16 7-16
+45o -45o
+45o
-45o +45o
-45o
9.1 inches
(230 mm)
31.6 inches
(803 mm)
17.2 inches
(438 mm)
11 inches
(280 mm)
Service Area
(cover removed)
Mounting Information
Description
Flange connection 12 x 12M at a graduated diameter of
208 mm, 0360 continuously adjustable.
158
17102170 MHz Trisector Antenna
X Polarization
General specications:
Frequency range 17102170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45 and -45
Front-to-back ratio >30 dB (co-polar)
(180 30) >25 dB (total power)
Connector 3 x 2 x 7-16 DIN female
Maximum input power 300 watts (at 50C)
per input
Weight 123.5 lb (56 kg)
Height 71.8 inches (1823 mm)
Radome diameter 9.1 inches (230 mm)
Wind load at 93 mph (150kph)
Side 72 lbf (320 N)
Wind survival rating 120 mph (200 kph)
Natural frequency 1921 Hz
Damping ratio 0.032
Shipping dimensions 79.9 x 15.7 x 15.7 inches
(2030 x 400 x 400 mm)
Specications: 17101880 MHz 18501990 MHz 19202170 MHz
Average gain (dBi) 17.2 17.5 17.2 17.6 17.8 17.6 17.8 17.9 17.4
Tilt 0 5 10 0 5 10 0 5 10
+45 and -45 polarization 66 (half-power) 63 (half-power) 60 (half-power)
horizontal beamwidth
+45 and -45 polarization 7 (half-power) 6.7 (half-power) 6.4 (half-power)
vertical beamwidth
Electrical downtilt 010 010 010
continuously adjustable (manual or optional remote control)
Sidelobe suppression for 0 5 10 T 0 5 10 T 0 5 10 T
rst sidelobe above horizon 17 15 15 dB 17 17 15 dB 17 17 15 dB
Cross polar ratio
Main direction 0 25 dB (typical) 20 dB (typical) 20 dB (typical)
Sector 60 >10 dB (typical) >10 dB (typical) >10 dB (typical)
Isolation intrasystem >30 dB >30 dB >30 dB
intersystem >45 dB >42 dB >42 dB
10895-C
936.2761/a
800 10360
65
17102170 MHz
X - POL
Adjustable Electrical Downtilt
010
Remote Control Option
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
17101880 MHz
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
18501990 MHz
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
0n
3
0
n
6
0
n
90n
1
2
0
n
1
5
0
n
180n 2
1
0
n
2
4
0
n
270n
3
0
0
n
3
3
0
n
3
10
20
30
19202170 MHz
Horizontal pattern
45- polarization
Vertical pattern
45- polarization
010 electrical downtilt
7-16
120o 240o
0o
1710 -2170 1710 -2170
1710 -2170
7-16
7-16 7-16
7-16 7-16
+45o -45o
+45o
-45o +45o
-45o
Service Area
(cover removed)
9.1 inches
(230 mm)
53.7 inches
(1365 mm)
17.2 inches
(438 mm)
11 inches
(280 mm)
Mounting Information
Description
Flange connection 12 x 12M at a graduated diameter of 208 mm, 0360 continuously adjustable.
159
Specications:
Outer diameter 180 mm
Cable diameter (6x) 1542 mm
Cable diameter (3x) 3.510.5 mm
Frame material Stainless steel
Sealing material Halogen-free cross linkable compound on
ethylene-propylene rubber (EPDM)
Fasteners Stainless steel
Accessories Mounting lubricant
Required assembly tools 6 mm socket wrench
Weight 4 lb (1.8 kg)
Shipping dimensions 8.2 x 8.2 x 2.7 inches
(208 x 208 x 68 mm)
10826-C
936.2670/a
110
51
25
5
25
30
38
9
1
1
7
0
1
8
0
Demanded dimensions of the installation interface:
183
172
1
2
+2
+0
+1
+0
Flexible Sealing Frame for Trisector Antenna
850 10010
160
Flexible Sealing Frame for Trisector Antenna
850 10010
Mounting instruction:
1)
Tighten all screws alternating and evenly. A crosswise tightening of the outer
screws will cause a more homogeneous distribution of sealing pressure.
After tightening, check extraction force of all cables.
Torque socket screw M8
1)
Max. 20 Nm (12x)
Insert the plugs
at unused holes
Pole with
installation interface
Gap 0.1 max. 0.5 mm
between cable and sealing
Feeder cable
. 4 . 3 . 2 . 1
. 8 . 7 . 6 . 5
700 MHz Fixed Tilt Panel Antennas
161
Horizontal Gain Model Electrical Height
Beamwidth Frequency (dBd) Series Downtilt Polarization (inches) Page
47 698894 12.8 840 21600 0 to 14 +45 and -45 51.2 163
698894 14.6 840 21630 0 to 10 +45 and -45 78 166
698894 15.8 840 21660 0 to 8 +45 and -45 103.8 169
60 698894 12 840 21210 0 to 14 +45 and -45 51.2 164
698894 13.5 840 21240 0 to 10 +45 and -45 78 167
698894 15 840 21270 0 to 8 +45 and -45 103.8 170
80 698894 10.8 840 21220 0 to 14 +45 and -45 51.7 165
698894 12.4 840 21250 0 to 10 +45 and -45 73 168
698894 13.8 840 21280 0 to 8 +45 and -45 104.9 171
698-894 MHz X Polarization
Horizontal Gain Model Electrical Height
Beamwidth Frequency (dBd) Series Downtilt Polarization (inches) Page
47 698894 / 17102170 12.8 / 16.2 840 21800 0 to 14 / 0 to 7 +45 and -45 51.2 172
698894 / 17102170 14.6 / 17.2 840 21830 0 to 10 / 0 to 5 +45 and -45 78 175
698894 / 17102170 15.8 / 18.2 840 21860 0 to 8 / 0 to 4 +45 and -45 103.8 178
60 698894 / 17102170 12 / 15.2 840 21410 0 to 14 / 0 to 7 +45 and -45 51.2 173
698894 / 17102170 13.5 / 16.2 840 21440 0 to 10 / 0 to 5 +45 and -45 78 176
698894 / 17102170 15 / 17.2 840 21470 0 to 8 / 0 to 4 +45 and -45 103.8 179
80 698894 / 17102170 10.8 / 14.2 840 21420 0 to 14 / 0 to 7 +45 and -45 51.7 174
698894 / 17102170 12.4 / 15.2 840 21450 0 to 10 / 0 to 5 +45 and -45 73 177
698894 / 17102170 13.8 / 16.2 840 21480 0 to 8 / 0 to 4 +45 and -45 104.9 180
698-894 MHz / 1710-2170 Dual Band XX Polarization
7
0
0
M
H
z
F
i
x
e
d
T
i
l
t
S
i
n
g
l
e
/
D
u
a
l
b
a
n
d
A N T E N N A S
I
mportant additions to Kathreins product line are these fixed tilt
antennas that provide operation in the 700 MHz wireless band.
All models will provide broadband coverage of the 800 MHz cellular
band; additional models will also offer broadband service for the
PCS/AWS band as well.
Rugged and reliable, these devices are being offered in a variety of
configurations that will permit integration of new services into legacy
sites with minimal impact. Both spatial and polarization diversity
schemes can be employed that will satisfy both existing CDMA or
GSM-based services, or soon to be deployed LTE systems that employ
2x or 4x diversity methods.
Kathrein offers models with fixed downtilts in two degree increments,
up to 14 in lowband and 8 highband in some models, and in
both vertically- and cross-polarized versions. Dual band models are
equipped with internal combiners to achieve feedline usage in both
high and low bands.
700 MHz Fi xed Ti l t
700 MHz Fixed Tilt Panel Antennas
162
163
698894 MHz Panel Antenna
X Polarization
11167-FRO/d
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 014 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -23 dB
envelope at 100 azimuth -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.2 x 14.7 x 4.1 inches (1301 x 374 x 103 mm)
Weight 19.4 lb (8.8 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 117 lbf / 49 lbf / 142 lbf
(520 N) / (215 N) / (632 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21600-00 Antenna with 0 electrical downtilt
840 21600-02 Antenna with 2 electrical downtilt
840 21600-04 Antenna with 4 electrical downtilt
840 21600-06 Antenna with 6 electrical downtilt
840 21600-08 Antenna with 8 electrical downtilt
840 21600-10 Antenna with 10 electrical downtilt
840 21600-12 Antenna with 12 electrical downtilt
840 21600-14 Antenna with 14 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
47
698894 MHz
4 ft X - POL
0 to 14 Electrical Downtilt
2 increments
840 21600 series
Specications: 698806 MHz 806894 MHz
Gain tilt 06 12.8 dBd 13.6 dBd
tilt 814 12.3 dBd 13.1 dBd
Horizontal beamwidth 49 45
@ 3 dB points
Vertical beamwidth 15.5 14
@ 3 dB points
4.1 inches
(103 mm)
39.4 inches
(1000 mm)
14.7 inches
(374 mm)
51.2 inches
(1301 mm)
3.9 inches
(100 mm)
Mounting Clamps Included
164
698894 MHz Panel Antenna
X Polarization
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 014 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -20 dB
envelope at 100 azimuth -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.2 x 14.7 x 4.1 inches (1301 x 374 x 103 mm)
Weight 20.9 lb (9.5 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 117 lbf / 49 lbf / 142 lbf
(520 N) / (215 N) / (632 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11138-B
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
Order Information:
Model Description
840 21210-00 Antenna with 0 electrical downtilt
840 21210-02 Antenna with 2 electrical downtilt
840 21210-04 Antenna with 4 electrical downtilt
840 21210-06 Antenna with 6 electrical downtilt
840 21210-08 Antenna with 8 electrical downtilt
840 21210-10 Antenna with 10 electrical downtilt
840 21210-12 Antenna with 12 electrical downtilt
840 21210-14 Antenna with 14 electrical downtilt
60
698894 MHz
4 ft X - POL
0 to 14 Electrical Downtilt
2 increments
840 21210 series
Specications: 698806 MHz 806894 MHz
Gain tilt 06 12 dBd 12.8 dBd
tilt 814 11.5 dBd 12.3 dBd
Horizontal beamwidth 63 60
@ 3 dB points
Vertical beamwidth 15.5 14
@ 3 dB points
4.1 inches
(103 mm)
39.4 inches
(1000 mm)
14.7 inches
(374 mm)
51.2 inches
(1301 mm)
3.9 inches
(100 mm)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
165
698894 MHz Panel Antenna
X Polarization
11139-FRO/g
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 014 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB
envelope at 90 azimuth -14 dB
envelope at 100 azimuth -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.7 x 11.8 x 5.9 inches (1314 x 300 x 151 mm)
Weight 34 lb (15.4 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 130 lbf / 47 lbf / 138 lbf
(575 N) / (209 N) / (610 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21220-00 Antenna with 0 electrical downtilt
840 21220-02 Antenna with 2 electrical downtilt
840 21220-04 Antenna with 4 electrical downtilt
840 21220-06 Antenna with 6 electrical downtilt
840 21220-08 Antenna with 8 electrical downtilt
840 21220-10 Antenna with 10 electrical downtilt
840 21220-12 Antenna with 12 electrical downtilt
840 21220-14 Antenna with 14 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
Specications: 698806 MHz 806894 MHz
Gain tilt 06 10.8 dBd 11.6 dBd
tilt 814 10.3 dBd 11.1 dBd
Horizontal beamwidth 80 75
@ 3 dB points
Vertical beamwidth 15.5 14
@ 3 dB points
5.9 inches
(151 mm)
55.8 inches
(1418 mm)
54.3 inches
(1378 mm)
51.7 inches
(1314 mm)
11.8 inches
(300 mm)
80
698894 MHz
4 ft X - POL
0 to 14 Electrical Downtilt
2 increments
840 21220 series
Mounting Clamps Included
166
698894 MHz Panel Antenna
X Polarization
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 010 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -23 dB
envelope at 100 azimuth -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 78 x 14.7 x 4.1 inches (1980 x 374 x 103 mm)
Weight 29.3 lb (13.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 178 lbf / 79 lbf / 350 lbf
(790 N) / (350 N) / (1038 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11168-FRO/e
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
Order Information:
Model Description
840 21630-00 Antenna with 0 electrical downtilt
840 21630-02 Antenna with 2 electrical downtilt
840 21630-04 Antenna with 4 electrical downtilt
840 21630-06 Antenna with 6 electrical downtilt
840 21630-08 Antenna with 8 electrical downtilt
840 21630-10 Antenna with 10 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
0o
o
10
20
30
40
50
60
70
80
90
3
0
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
47
698894 MHz
6 ft X - POL
0 to 10 Electrical Downtilt
2 increments
840 21630 series
Specications: 698806 MHz 806894 MHz
Gain tilt 06 14.6 dBd 15.4 dBd
tilt 810 14.1 dBd 14.9 dBd
Horizontal beamwidth 49 45
@ 3 dB points
Vertical beamwidth 10.7 9.5
@ 3 dB points
4.1 inches
(103 mm)
30.3 inches
(770 mm)
14.7 inches
(374 mm)
78 inches
(1980 mm)
3.9 inches
(100 mm)
30.3 inches
(770 mm)
Mounting Clamps Included
167
698894 MHz Panel Antenna
X Polarization
11141-FRO/d
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 010 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -20 dB
envelope at 100 azimuth -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 78 x 14.7 x 4.1 inches (1980 x 374 x 103 mm)
Weight 29.8 lb (13.5 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 178 lbf / 79 lbf / 350 lbf
(790 N) / (350 N) / (1038 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21240-00 Antenna with 0 electrical downtilt
840 21240-02 Antenna with 2 electrical downtilt
840 21240-04 Antenna with 4 electrical downtilt
840 21240-06 Antenna with 6 electrical downtilt
840 21240-08 Antenna with 8 electrical downtilt
840 21240-10 Antenna with 10 electrical downtilt
60
698894 MHz
6 ft X - POL
0 to 10 Electrical Downtilt
2 increments
840 21240 series
Specications: 698806 MHz 806894 MHz
Gain tilt 06 13.5 dBd 14.3 dBd
tilt 810 13.5 dBd 13.8 dBd
Horizontal beamwidth 63 60
@ 3 dB points
Vertical beamwidth 10.7 9.5
@ 3 dB points
4.1 inches
(103 mm)
30.3 inches
(770 mm)
14.7 inches
(374 mm)
78 inches
(1980 mm)
3.9 inches
(100 mm)
30.3 inches
(770 mm)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
168
698894 MHz Panel Antenna
X Polarization
11142-FRO/f
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 010 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB
envelope at 90 azimuth -14 dB
envelope at 100 azimuth -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 73 x 11.8 x 5.9 inches (1854 x 300 x 151 mm)
Weight 44 lb (20 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 199 lbf / 71 lbf / 208 lbf
(883 N) / (315 N) / (923 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21250-00 Antenna with 0 electrical downtilt
840 21250-02 Antenna with 2 electrical downtilt
840 21250-04 Antenna with 4 electrical downtilt
840 21250-06 Antenna with 6 electrical downtilt
840 21250-08 Antenna with 8 electrical downtilt
840 21250-10 Antenna with 10 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
0o
o
10
20
30
40
50
60
70
80
90
3
0
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
Specications: 698806 MHz 806894 MHz
Gain tilt 06 12.4 dBd 13.4 dBd
tilt 810 11.9 dBd 12.9 dBd
Horizontal beamwidth 80 75
@ 3 dB points
Vertical beamwidth 10.7 9.5
@ 3 dB points
80
698894 MHz
6 ft X - POL
0 to 10 Electrical Downtilt
2 increments
840 21250 series
5.9 inches
(151 mm)
77.1 inches
(1958 mm)
75.5 inches
(1918 mm)
73 inches
(1854 mm)
11.8 inches
(300 mm)
Mounting Clamps Included
169
698894 MHz Panel Antenna
X Polarization
11169-FRO/e
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 08 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -23 dB
envelope at 100 azimuth -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 103.8 x 14.7 x 4.1 inches (2637 x 374 x 103 mm)
Weight 38.1 lb (17.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 237 lbf / 105 lbf / 291 lbf
(1053 N) / (467 N) / (1294 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21660-00 Antenna with 0 electrical downtilt
840 21660-02 Antenna with 2 electrical downtilt
840 21660-04 Antenna with 4 electrical downtilt
840 21660-06 Antenna with 6 electrical downtilt
840 21660-08 Antenna with 8 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
47
698894 MHz
8 ft X - POL
0 to 8 Electrical Downtilt
2 increments
840 21660 series
4.1 inches
(103 mm)
40.1 inches
(1018 mm)
14.7 inches
(374 mm)
103.8 inches
(2637 mm)
3.9 inches
(100 mm)
40.1 inches
(1018 mm)
Specications: 698806 MHz 806894 MHz
Gain tilt 06 15.8 dBd 16.6 dBd
tilt 8 15.3 dBd 16.1 dBd
Horizontal beamwidth 49 45
@ 3 dB points
Vertical beamwidth 7.8 6.8
@ 3 dB points
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
Mounting Clamps Included
170
698894 MHz Panel Antenna
X Polarization
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR
1
/ Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM
1
(2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 Degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 08 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB
envelope at 90 azimuth -20 dB
envelope at 100 azimuth -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female (sealable long neck) (backmounted)
Dimensions L x W x D 103.8 x 14.7 x 4.1 inches (2637 x 374 x 103 mm)
Weight 38.1 lb (17.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 237 lbf / 105 lbf / 291 lbf
(1053 N) / (467 N) / (1294 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11144-B
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
Order Information:
Model Description
840 21270-00 Antenna with 0 electrical downtilt
840 21270-02 Antenna with 2 electrical downtilt
840 21270-04 Antenna with 4 electrical downtilt
840 21270-06 Antenna with 6 electrical downtilt
840 21270-08 Antenna with 8 electrical downtilt
60
698894 MHz
8 ft X - POL
0 to 8 Electrical Downtilt
2 increments
840 21270 series
Specications: 698806 MHz 806894 MHz
Gain 15 dBd 15.8 dBd
Horizontal beamwidth 63 60
@ 3 dB points
Vertical beamwidth 7.8 6.8
@ 3 dB points
4.1 inches
(103 mm)
40.1 inches
(1018 mm)
14.7 inches
(374 mm)
103.8 inches
(2637 mm)
3.9 inches
(100 mm)
40.1 inches
(1018 mm)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
171
698894 MHz Panel Antenna
X Polarization
11145-FRO/e
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
Specications:
Frequency range 698894 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C)
Electrical downtilt range 08 degrees (2 increments)
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB
envelope at 90 azimuth -14 dB
envelope at 100 azimuth -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB
30<azimuth<60 >10 dB
Primary test frequencies 752 MHz, 782 MHz
Secondary test frequencies 704 MHz, 734 MHz
835 MHz, 880 MHz
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 104.9 x 11.8 x 5.9 inches (2664 x 300 x 151 mm)
Weight 57 lb (25.9 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 289 lbf / 106 lbf / 303 lbf
(1285 N) / (470 N) / (1344 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Order Information:
Model Description
840 21280-00 Antenna with 0 electrical downtilt
840 21280-02 Antenna with 2 electrical downtilt
840 21280-04 Antenna with 4 electrical downtilt
840 21280-06 Antenna with 6 electrical downtilt
840 21280-08 Antenna with 8 electrical downtilt
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
Specications: 698806 MHz 806894 MHz
Gain tilt 06 13.8 dBd 14.6 dBd
tilt 8 13.3 dBd 14.1 dBd
Horizontal beamwidth 80 75
@ 3 dB points
Vertical beamwidth 7.8 6.8
@ 3 dB points
5.9 inches
(151 mm)
109 inches
(2768 mm)
107.4 inches
(2728 mm)
104.9 inches
(2664 mm)
11.8 inches
(300 mm)
80
698894 MHz
8 ft X - POL
0 to 8 Electrical Downtilt
2 increments
840 21280 series
Mounting Clamps Included
172
698894 /17102170 MHz Panel Antenna
with Integrated Combiner XX Polarization
47 // 40
698894 MHz
17102170 MHz
4 ft XX - POL
0 to 14, 0 to 8
Electrical Downtilt
2 increments
840 21800 series
11173-FRO/e
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB // >30 dB
(worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -23 dB // -23 dB
envelope at 100 azimuth -25 dB // -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 014 degrees // 08 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.2 x 14.7 x 4.1 inches (1301 x 374 x 103 mm)
Weight 22.7 lb (10.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 117 lbf / 49 lbf / 142 lbf
(520 N) / (215 N) / (632 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 08 12.8 dBd 13.6 dBd 16.2 dBd 16.5 dBd 16.8 dBd
tilt 814 12.3 dBd 13.1 dBd
Horizontal beamwidth 49 45 42 40 38
@ 3 dB points
Vertical beamwidth 15.5 14 8 7.5 7
@ 3 dB points
4.1 inches
(103 mm)
39.4 inches
(1000 mm)
14.7 inches
(374 mm)
51.2 inches
(1301 mm)
3.9 inches
(100 mm)
Order Information:
Model Description
840 21800-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
08
Lowband
Tilt (-xx)
00
02
04
06
08
10
12
14
Mounting Clamps Included
173
698894 /17102170 MHz Panel Antenna
XX Polarization with Integrated Combiner
60
698894 MHz
17102170 MHz
4 ft XX - POL
0 to 14, 0 to 8
Electrical Downtilt
2 increments
840 21410 series
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -20 dB // -20 dB
envelope at 100 azimuth -23 dB // -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 014 degrees // 08 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.2 x 14.7 x 4.1 inches (1301 x 374 x 103 mm)
Weight 22.7 lb (10.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 117 lbf / 49 lbf / 142 lbf
(520 N) / (215 N) / (632 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11156-FRO/e
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 08 12 dBd 12.8 dBd 15.2 dBd 15.5 dBd 15.8 dBd
tilt 814 11.5 dBd 12.3 dBd
Horizontal beamwidth 63 60 63 61 59
@ 3 dB points
Vertical beamwidth 15.5 14 8 7.5 7
@ 3 dB points
4.1 inches
(103 mm)
39.4 inches
(1000 mm)
14.7 inches
(374 mm)
51.2 inches
(1301 mm)
3.9 inches
(100 mm)
Order Information:
Model Description
840 21410-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
08
Lowband
Tilt (-xx)
00
02
04
06
08
10
12
14
Mounting Clamps Included
174
698894 /17102170 MHz Panel Antenna
with Integrated Combiner XX Polarization
80
698894 MHz
17102170 MHz
4 ft XX - POL
0 to 14, 0 to 6
Electrical Downtilt
2 increments
840 21420 series
11157-FRO/g
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB // -10 dB
envelope at 90 azimuth -14 dB // -14 dB
envelope at 100 azimuth -17 dB // -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 014 degrees // 08 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 51.7 x 11.8 x 5.9 inches (1314 x 300 x 151 mm)
Weight 34 lb (15.4 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 130 lbf / 47 lbf / 138 lbf
(575 N) / (209 N) / (610 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Mounting Equipment:
Description Weight
2-point mounting kit for 2 to 4.5 inch 4 lb (1.8 kg)
(50 to 115 mm) OD mast.
2-point tilt kit 7.4 lb (3.7 kg)
015 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 08 10.8 dBd 11.6 dBd 14.2 dBd 14.5 dBd 14.8 dBd
tilt 814 10.3 dBd 11.1 dBd
Horizontal beamwidth 80 75 78 82 86
@ 3 dB points
Vertical beamwidth 15.5 14 8 7.5 7
@ 3 dB points
Order Information:
Model Description
840 21420-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
08
Lowband
Tilt (-xx)
00
02
04
06
08
10
12
14
5.9 inches
(151 mm)
55.8 inches
(1418 mm)
54.3 inches
(1378 mm)
51.7 inches
(1314 mm)
11.8 inches
(300 mm)
Mounting Clamps Included
175
698894 /17102170 MHz Panel Antenna
XX Polarization with Integrated Combiner
47 // 40
698894 MHz
17102170 MHz
6 ft XX - POL
0 to 10, 0 to 6
Electrical Downtilt
2 increments
840 21830 series
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB // >30 dB
(worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -23 dB // -23 dB
envelope at 100 azimuth -25 dB // -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 010 degrees // 06 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 78 x 14.7 x 4.1 inches (1980 x 374 x 103 mm)
Weight 33.7 lb (15.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 178 lbf / 79 lbf / 234 lbf
(790 N) / (350 N) / (1038 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11174-FRO/f
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
0o
o
10
20
30
40
50
60
70
80
90
3
0
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 06 14.6 dBd 15.4 dBd 17.2 dBd 17.5 dBd 17.8 dBd
tilt 810 14.1 dBd 14.9 dBd
Horizontal beamwidth 49 45 42 40 38
@ 3 dB points
Vertical beamwidth 10.7 9.5 5.5 5.1 4.7
@ 3 dB points
Order Information:
Model Description
840 21830-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
Lowband
Tilt (-xx)
00
02
04
06
08
10
4.1 inches
(103 mm)
30.3 inches
(770 mm)
14.7 inches
(374 mm)
78 inches
(1980 mm)
3.9 inches
(100 mm)
30.3 inches
(770 mm)
Mounting Clamps Included
176
698894 /17102170 MHz Panel Antenna
with Integrated Combiner XX Polarization
60
698894 MHz
17102170 MHz
6 ft XX - POL
0 to 10, 0 to 8
Electrical Downtilt
2 increments
840 21440 series
11159-FRO/f
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.64 dB
(< 1.4:1 / >15.56 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -20 dB // -20 dB
envelope at 100 azimuth -23 dB // -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 010 degrees // 06 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 78 x 14.7 x 4.1 inches (1980 x 374 x 103 mm)
Weight 33.7 lb (15.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 178 lbf / 79 lbf / 234 lbf
(790 N) / (350 N) / (1038 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
0o
o
10
20
30
40
50
60
70
80
90
3
0
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 06 13.5 dBd 14.3 dBd 16.2 dBd 16.5 dBd 16.8 dBd
tilt 810 13 dBd 13.8 dBd
Horizontal beamwidth 63 60 63 61 59
@ 3 dB points
Vertical beamwidth 10.7 9.5 5.5 5.1 4.7
@ 3 dB points
4.1 inches
(103 mm)
30.3 inches
(770 mm)
14.7 inches
(374 mm)
78 inches
(1980 mm)
3.9 inches
(100 mm)
30.3 inches
(770 mm)
Order Information:
Model Description
840 21440-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
Lowband
Tilt (-xx)
00
02
04
06
08
10
Mounting Clamps Included
177
698894 /17102170 MHz Panel Antenna
XX Polarization with Integrated Combiner
80
698894 MHz
17102170 MHz
6 ft XX - POL
0 to 10, 0 to 6
Electrical Downtilt
2 increments
840 21450 series
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB // -10 dB
envelope at 90 azimuth -14 dB // -14 dB
envelope at 100 azimuth -17 dB // -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 010 degrees // 06 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 73 x 11.8 x 5.9 inches (1854 x 300 x 151 mm)
Weight 44 lb (20 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 199 lbf / 71 lbf / 208 lbf
(883 N) / (315 N) / (923 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11160-FRO/g
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
010 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
0o
o
10
20
30
40
50
60
70
80
90
3
0
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 06 12.4 dBd 13.4 dBd 15.2 dBd 15.5 dBd 15.8 dBd
tilt 810 11.9 dBd 12.9 dBd
Horizontal beamwidth 80 75 78 82 86
@ 3 dB points
Vertical beamwidth 10.7 9.5 5.5 5.1 4.7
@ 3 dB points
Order Information:
Model Description
840 21450-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
06
Lowband
Tilt (-xx)
00
02
04
06
08
10
5.9 inches
(151 mm)
77.1 inches
(1958 mm)
75.5 inches
(1918 mm)
73 inches
(1854 mm)
11.8 inches
(300 mm)
Mounting Clamps Included
178
698894 /17102170 MHz Panel Antenna
with Integrated Combiner XX Polarization
47 // 40
698894 MHz
17102170 MHz
8 ft XX - POL
0 to 8, 0 to 4
Electrical Downtilt
2 increments
840 21860 series
11175-FRO/e
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB // >30 dB
(worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -23 dB // -23 dB
envelope at 100 azimuth -25 dB // -25 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 08 degrees // 04 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 103.8 x 14.7 x 4.1 inches (2637 x 374 x 103 mm)
Weight 42.6 lb (19.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 237 lbf / 105 lbf / 291 lbf
(1053 N) / (467 N) / (1294 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
4.1 inches
(103 mm)
40.1 inches
(1018 mm)
14.7 inches
(374 mm)
103.8 inches
(2637 mm)
3.9 inches
(100 mm)
40.1 inches
(1018 mm)
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 04 15.8 dBd 16.6 dBd 18.2 dBd 18.5 dBd 18.8 dBd
tilt 8 15.3 dBd 16.1 dBd
Horizontal beamwidth 49 45 42 40 38
@ 3 dB points
Vertical beamwidth 7.8 6.8 4 3.7 3.4
@ 3 dB points
Order Information:
Model Description
840 21860-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
Lowband
Tilt (-xx)
00
02
04
06
08
Mounting Clamps Included
179
698894 /17102170 MHz Panel Antenna
XX Polarization with Integrated Combiner
60
698894 MHz
17102170 MHz
8 ft XX - POL
0 to 8, 0 to 4
Electrical Downtilt
2 increments
840 21470 series
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR
1
/ Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM
1
(2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >30 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -15 dB // -15 dB
envelope at 90 azimuth -20 dB // -20 dB
envelope at 100 azimuth -23 dB // -23 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 08 degrees // 04 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 103.8 x 14.7 x 4.1 inches (2637 x 374 x 103 mm)
Weight 42.5 lb (19.3 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 237 lbf / 105 lbf / 291 lbf
(1053 N) / (467 N) / (1294 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
11162-FRO/f
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
Order Information:
Model Description
840 21470-xx-yy Dualband antenna with
electrical downtilt
Highband
Tilt (-yy)
00
02
04
Lowband
Tilt (-xx)
00
02
04
06
08
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 04 15 dBd 15.8 dBd 17.2 dBd 17.5 dBd 17.8 dBd
tilt 8 14.5 dBd 15.3 dBd
Horizontal beamwidth 63 60 63 61 59
@ 3 dB points
Vertical beamwidth 7.8 6.8 4 3.7 3.4
@ 3 dB points
4.1 inches
(103 mm)
40.1 inches
(1018 mm)
14.7 inches
(374 mm)
103.8 inches
(2637 mm)
3.9 inches
(100 mm)
40.1 inches
(1018 mm)
Mounting Clamps Included
180
698894 /17102170 MHz Panel Antenna
with Integrated Combiner XX Polarization
80
698894 MHz
17102170 MHz
8 ft XX - POL
0 to 8, 0 to 4
Electrical Downtilt
2 increments
840 21480 series
11163-FRO/f
Specications:
Frequency range 698894 MHz // 17102170 MHz
Impedance 50 ohms
VSWR / Return loss < 1.35:1 / >16.5 dB @ primary test frequencies
(< 1.43:1 / >15 dB @ secondary test frequencies)
PIM (2x20w) IM3 IM5 IM7-9
<-150 dBc <-160 dBc <-170 dBc
Polarized +45 and -45
Front-to-back ratio >25 dB (worst case, within 20 degree cone)
Power handling 500 watts (at 50C) // 250 watts (at 50C)
per connector
Isolation >30 dB
Normalized radiation pattern
envelope at 80 azimuth -10 dB // -10 dB
envelope at 90 azimuth -14 dB // -14 dB
envelope at 100 azimuth -17 dB // -17 dB
Crosspolar discrimination
azimuth < 30 >20 dB // >20 dB
30<azimuth<60 >10 dB // >10 dB
Primary test frequencies 752 MHz, 782 MHz // 1880 MHz, 1960 MHz
Secondary test frequencies 704 MHz, 734 MHz // 1750 MHz, 2150 MHz
835 MHz, 880 MHz
Electrical downtilt range 08 degrees // 04 degrees
(2 increments)
Lightning protection Chassis ground
Connector 2 x 7-16 DIN female
(sealable long neck) (backmounted)
Dimensions L x W x D 104.9 x 11.8 x 5.9 inches (2664 x 300 x 151 mm)
Weight 57 lb (25.9 kg)
Wind load at 93 mph (150kph)
Front/Side/Rear 289 lbf / 106 lbf / 303 lbf
(1285 N) / (470 N) / (1344 N)
Radome UV-resistant berglass
Wind survival 150 mph (240 kph)
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
17102170 MHz
Vertical pattern
45 - polarization
Horizontal pattern
45 - polarization
698894 MHz
Mounting Equipment:
Description Weight
3-point mounting kit for 2 to 4.5 inch 6 lb (2.7 kg)
(50 to 115 mm) OD mast.
3-point tilt kit 13.3 lb (6 kg)
07 degrees downtilt angle.
See illustrations and instructions on pages 181182
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
10
20
30
40
50
60
70
80
90
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3 0 2 0 1 6 3 6 10 20
3
6
10
20
B d B d
dB
%
Specications: MHz 698806 806894 17101880 18501990 19202170
Gain tilt 06 // 04 13.8 dBd 14.6 dBd 16.2 dBd 16.5 dBd 16.8 dBd
tilt 8 13.3 dBd 14.1 dBd
Horizontal beamwidth 80 75 78 82 86
@ 3 dB points
Vertical beamwidth 7.8 6.8 4 3.7 3.4
@ 3 dB points
Order Information:
Model Description
840 21480-xx-yy Dualband antenna with electrical downtilt
Highband
Tilt (-yy)
00
02
04
Lowband
Tilt (-xx)
00
02
04
06
08
5.9 inches
(151 mm)
109 inches
(2768 mm)
107.4 inches
(2728 mm)
104.9 inches
(2664 mm)
11.8 inches
(300 mm)
Mounting Clamps Included
181
3-point Mounting Hardware
for 6 ft and 8 ft Antennas
2-point Mounting Hardware
for 4 ft Antennas
Mounting Brackets
for use with 2-point mount 21000 series antennas
Mast dia. 24.5 inches (50115 mm)
Weight: 4 lb (1.8 kg)
Mounting Brackets
for use with 3-point mount 21000 series antennas
Mast dia. 24.5 inches (50115 mm)
Weight: 6 lb (2.7 kg)
Mechanical Tilt Brackets
for use with 2-point mount 21000 series antennas
Weight: 7.4 lb (3.7 kg)
64 mm
M8
Mechanical Tilt Brackets
for use with 3-point mount 21000 series antennas
Weight: 13.3 lb (6 kg)
64 mm
M8
21000 series
Mounting Hardware
182
21000 series
Mounting Information
Note: Antenna must be
mounted with the
drain holes at the
bottom.
47 and 60 Panel Antennas 80 Panel Antennas
Dout
Dout Dout
742 033* 742 034*
Mast dia. 4.5" (114.3 mm) 5.5" (139.7 mm)
22.5 inches 23.25 inches
(572 mm) (591 mm)
2-Point
3-Sector Mounting
Drain Location
* 3-sector mounting systems are 2-point mounting arrangements. For antennas with 3 mounting points, consultation with structural
designers/engineers is strongly recommended in accordance with local regulations. See page 358 for sector mount kit specications.
Dout Dout
742 033* 742 034*
Mast dia. 4.5" (114.3 mm) 5.5" (139.7 mm)
25.5 inches 26.5 inches
(648 mm) (673.1 mm)
2-Point
3-Sector Mounting
Dout
Remote Electrical Downtilt
Model Description Page
860 10147 Remote control unit 192
860 10148 Remote control unit 192
860 10006 Central control unit 193
860 10026 Central control unit 193
860 10046 Portable control adapter 195
860 10002 RET remote control signal splitter 196
860 10030 Lightning protection device 197
782 10253 Smart bias tee 198
782 10254 Smart bias tee 198
782 10255 Smart bias tee 198
782 10256 Smart bias tee 198
782 10453 Smart bias tee 198
782 10454 Smart bias tee 198
782 10455 Smart bias tee 198
782 10456 Smart bias tee 198
782 11055 Smart bias tee 201
782 11056 Smart bias tee 201
782 10577 Bias Tee 203
782 10578 Bias Tee 203
782 10429 Bias Tee 205
793 304 Bias tee 206
793 301 DC stop 207
782 10850 DC stop 208
840 104nn Series Remote Control Cables -Black (150 m and 200 m) 209
GC-1 Grounding clamp 211
850 10005 Kathrein installation tool 212
183
R
E
T
R
e
m
o
t
e
E
l
e
c
t
r
i
c
a
l
T
i
l
t
C O M P O N E N T S
Re mo t e El e c t r i c a l Ti l t
I
n contrast to legacy wireless systems, using fixed cell sizes, advanced
networks will be dynamically re-configurable to accommodate the
demands of subscriber loading, time of day, seasonal adjustments
and system expansion. In any newly designed or upgraded wireless
system, coverage adjustments may be made by varying vertical
beam tilt to lengthen or shorten sector range. Kathreins advanced
antennas have continuously adjustable downtilt by optional tilt control
units under local or remote control. Tilt in each band covered by the
antenna is independently adjustable.
Site optimization can be accomplished when construction is complete
and adjusted easily and quickly in the future as operating conditions
evolve. Adjustment is possible by on-site personnel, with no need for
tower climbing. Via Ethernet link, control from the network control
center may be accomplished, by network operators or dynamically
by the network control system. Coverage adjustments may be
made anytime, without the need to power down a site. This may
be especially valuable where site access may be difficult, such as
installations on high voltage transmission towers.
Kathrein offers a complete solution for Remote Electrical Downtilt, with
all the components to accomplish this vital improvement to capacity
and reliability: antennas, motor controls, control cable splitters, control
units, and accessories. In addition, some Kathrein antennas have
integrated remote control actuators.
Kathreins Remote Electrical Tilt (RET) system advantages:
Limited site access and/or time restrictions become irrelevant
No special platforms or other means of access to the antenna
are required
Adjustments can be made and the appropriate measurements
performed quickly and economically
Network alterations can be carried out despite adverse
weather conditions
Cells remain fully operational while changes are being made
Permits site optimization at stealth or difficult-to-access sites
184
185
Kathrein is a member of the Antenna Interface
Standards Group that has the objective of
introducing open control standards for base station
antennas with remotely adjustable tilt.
RET Components:
RCU (Remote Control Unit)
CCU (Central Control Unit)
DC Power and Signal Splitter
Control Cable
Lightning Protection Device
Grounding Kit
Optional:
Dual Band Combiners See TMAs, Filters,
Electrical Accessories section for more detail
Smart Bias Tee
DTMA (Double Tower Mounted Amplifier)
See TMAs, Filters, Electrical Accessories
section for more detail
Remote Control Unit
Portable Control Unit
Signal Splitter
Lightning Protection
Device
Central Control Unit
Remote Control
Cables
Smart Bias Tee
Grounding Kit
Remote Electric Tilt
186
Typical RET Site Configurations
Three options are offered for communication between the CCU and RCUs:
Individual control cables (with splitters and/or daisy chain feature on RCUs)
Using Smart Bias Tees to multiplex control signals onto the feeder lines
Using a combination of Bias Tee and TMAs
Remote Electric Tilt
187
RET System Control:
Central Control Unit (CCU)
The major component for controlling the
RCUs is the Central Control Unit (CCU),
installed at the BTS.
The CCU can be accessed from the network
control center via the Ethernet input and/or directly through a personal computer
via the RS 232 input or Ethernet input. No special software is required for standard
operation. AC/DC and DC-only models are available.
The CCU appears as an addressable IP device to the controlling computer or network
and is accessed via standard Web browser (e.g. Internet Explorer). IP addresses are user
programmable; access is password protected.
The display which appears contains all the required control functions for normal
service and installation. In addition to permitting the configuration and control of
the connected RCUs and TMAs, the CCU program also displays the device status,
command history list and various types of system errors. All AISG alarms can be read
via the alarm interface.
The software and firmware associated with both the CCUs and RCUs are continually
evolving and may be updated easily using the update pages available in the browser
application. Upgrade software may be obtained on request; registered users of
Kathrein-Scalas on-line data library may download updates from the library.
The CCU also provides 8 user-programmable open-collector alarm outputs for interface
with the BTS.
For more detail, please see the RET Software Manual, or the RET Hardware Manual,
available on request.
Portable Control Adapter (PCA)
The PCA is a portable controller for Kathreins Remote Electrical Tilt system (RET). It is
a simple device for operating remote control units (RCUs) attached to Kathrein base
station antennas. This product is designed for use by installers or maintenance staff
with temporary site access. A standard Central Control Unit (CCU) is not required.
Control from the network operations center is not available using the PCA.
The PCA consists of a small control box and Windows- based software installed on a
laptop. The control box transforms the USB inter-face into an AISG-compatible interface
(RS 485 + DC voltage). Together with the supplied Windows-based software, all
functions of the RCU can be controlled via a laptop or PC.
Up to 27 RCUs can be controlled using a single PCA. A site may be upgraded for
remote control via the network control center by replacing the PCA with a standard
CCU.
Remote Electric Tilt
188
10922-D
850 10005
Installation Tool
Use of improper tools
may damage the
interfaces. Kathrein
strongly recommends
using the 850-10005
Installation Tool with a
standard torque wrench
to tighten the nuts of the
feeder line connectors.
Sealing of cap nuts
on correctly installed
connectors for additional
weather protection is
not required. It is not
recommended by the
connector manufacturers.
Note
Remote Electric Tilt
Feeder Line Installation for Panel Antennas with
Four Connectors on Two Levels
Feeder Line Installation
Kathreins 850 10005 installation tool is suitable for either 27
mm or 32 mm 7-16 DIN connectors.
Tighten the nut within a torque range of 18.524.4 lb-ft
depending on the connector manufacturers specications.
Two tools are included (27 mm and 32 mm).
Fits a standard
1
2 inch drive torque wrench.
1/2" square drive
Step 2
Step 1
There are four interfaces for
feeding the antenna located at
the bottom.
To make the installation of the
feeder lines and the connectors
easier, the interfaces are
arranged on two levels.
The feeder line installation
sequence is: 1, 2, 3, 4.
Put the connector carefully in
place and hand-screw the nut on.
Use a torque wrench to nish the
installation (see the 850-10005
Installation Tool).
After the feeder lines have been
installed the remote control units
(RCU) can be installed.
See the instructions "Attaching
the RCU" for details.
189
Kathreins 850 10005 installation tool is suitable for either 27
mm or 32 mm 7-16 DIN connectors.
Tighten the nut within a torque range of 18.524.4 lb-ft
depending on the connector manufacturers specications.
Two tools are included (27 mm and 32 mm).
Fits a standard
1
2 inch drive torque wrench.
1/2" square drive
Use of improper tools
may damage the
interfaces. Kathrein
strongly recommends
using the 850 10005
Installation Tool with a
standard torque wrench
to tighten the nuts of the
feeder line connectors.
Connector Arrangement
There are six RF connections and three RET
interfaces located at the bottom of the antenna.
Do not remove the RCU
connection covers until the
feeder line installation is
complete.
The downtilt must be set
to 0 before the RCU is
installed (see the instructions
Attaching the RCU for
details).
Not following these
instructions may damage the
downtilt spindle.
Step 2
After the feeder lines have been
installed the remote control units
(RCU) can be installed.
The RCU installation sequence
is: 1, 2, 3.
See the instructions "Attaching
the RCU" for details.
Sealing of cap nuts
on correctly installed
connectors for additional
weather protection is
not required. It is not
recommended by the
connector manufacturers.
Note
Remote Electric Tilt
850 10005
Installation Tool
Feeder Line Installation forTriple-band Antennas
Feeder Line Installation
Step 1
The feeder line installation
sequence is: 4, 5, 6, 7, 8, 9.
Put the connector carefully in
place and hand-screw the nut on.
Use a torque wrench to nish the
installation (see the 850-10005
Installation Tool).
Repeat the operations shown in
gures A and B for each feeder
line.
190
191
Remote Electric Tilt Control Cable Installation
Lightning Protection Device
Remote Control
Signal Spitter
Step 1
Connect a control cable to the
daisy chain input on the RCU.
If the daisy chain output is not
used, do not remove the daisy
chain output protection plug.
Daisy chain in Daisy chain out
Bottom of RCU
Step 2
To use the daisy chain option.
Remove the daisy chain output
protection plug.
Connect a control cable to the
daisy chain output on the
RCU.
Connect the other end of the
control cable to the daisy chain
input on the next RCU.
Do not remove the daisy chain
termination plug from the last
RCU device.
Dress cables using black
UV-resistant cable ties .
When installing or
removing cables, turn
ONLY the threaded collar
indicated, not the body of
the connector. Rotating
the connector body can
result in permanent
damage to the connector
and the device being
installed. Note that the
connectors have keyways
which must be carefully
aligned before insertion.
Insert the connector fully
until well seated before
tightening.
Turn this collar
Turn this
collar
Includes grounding cable with attached lug, one roll of butyl rubber
tape, one roll of PVC tape, and hardware.
Specications:
Maximum lightning current >20 kA (pulse 10/350 sec)
Protection class IP 68
Grounding Via stranded grounding wire
6 gauge, length 24 inches,
2-hole lug terminal (
3
/8 in. lug) attached
Nominal size
1
/4 or
3
/8 inch
Bonding conductor jacket PE
material type
Grounding strap material Copper
Waterproong method Butyl rubber and PVC tape
Note The grounding kit is only suitable for use with Kathrein power supply and
signal cables:
860 10007 to 860 10015
860 10029
860 10032
860 10033
860 10054 to 860 10060
10925-B
GC-1
Grounding Clamp
2.22.3 inches
0.2450.38 inches
212
Remote Electric Tilt
Kathrein Installation Tool
850 10005
Kathrein's 850 10005 installation tool is suitable for either 27
mm or 32 mm 7-16 DIN connectors.
Tighten the nut within a torque range of 18.524.4 lb-ft
(2533 Nm) depending on the connector manufacturer's
specications.
Two tools are included (27mm and 32 mm).
Fits standard
1
2
inch drive torque wrench.
10878-A
936.2435/b
1/2 square actuation
according to DIN 3120
Form C
27 or 32 mm
Other Directional Antennas
Maximum
Frequency Gain Model Polarization Input Power Connector Page
790960 MHz 5 dBi 738 445 V 200 watts 7-16 DIN 215
17101880 MHz 5.5 dBi
18802170 MHz 6.5 dBi
790960 MHz 5 dBi 738 446 V 200 watts N female 215
17101880 MHz 5.5 dBi
18802690 MHz 6.5 dBi
Frequency Gain Model Polarization Connector Length Page
7901000 MHz 11 dBi 742 192V01 V 7-16 DIN 30.9 inches 216
10001700 MHz 11.3 dBi
17002170 MHz 11.5 dBi
806960 MHz 10 dBi CL-900B H or V N female 29 inches 223
Log Periodic
Frequency Gain Model Polarization Connector Length Page
806869 MHz 12 dBi TY-840 H or V N female 24.5 inches 217
824894 MHz 12 dBi TY-860 H or V N female 24.25 inches 217
890960 MHz 12 dBi TY-900 H or V N female 23 inches 217
806869 MHz 12 dBi RY-840B H or V N female 29 inches 218
824894 MHz 12 dBi RY-860B H or V N female 29 inches 218
890960 MHz 12 dBi RY-900B H or V N female 29 inches 218
Yagi
Bi-Directional Multiband
Frequency Gain Model Polarization Connector Width Page
890960 MHz 16 dBi MF-900B V N female 46.5 inches 221
928953 MHz 16 dBi MF-940B V N female 46.5 inches 221
940960 MHz 16 dBi MF-950B V N female 46.5 inches 221
806869 MHz 18 dBi PR-850 H or V N female 68 inches 219
890960 MHz 18 dBi PR-900 H or V N female 68 inches 219
940960 MHz 18 dBi PR-950 H or V N female 68 inches 219
Half-Parabolic
213
O
t
h
e
r
D
i
r
e
c
t
i
o
n
a
l
A
n
t
e
n
n
a
s
A N T E N N A S
K
athrein offers the system designer a choice of many
directional antenna types for fixed station applications:
Yagis, both open and radome protected, will provide long
term reliability and economy for control station, point to point
and point to multipoint applications.
Log periodic antennas offer broadband performance in
rugged, weather resistant fiberglass radomes.
Kathrein-Scalas Paraflector and Miniflector Series
half-parabolic antennas offer higher gain and greater front-to-
back performance than Yagis; they excel in applications where
longevity and performance are demanded.
Kathreins logs, Yagis and the Miniflector and Paraflector series
offer flexibility in system design, usable for horizontal or vertical
polarization.
Our Bi-directional antennas are the perfect complement for
fill-in applications for dual band carriers. Covering both the
806-960 and 1710 -2180 MHz bands, they are an excellent
choice for enclosed spaces such as arenas and stadiums, as
well as for temporary installations.
O T H E R
214
215
Bi-Directional Multiband Antenna
V Polarization
10700-E
936.1870/e
H-plane 790-960 MHz
Horizontal pattern V-polarization
E-plane 790-960 MHz
Vertical pattern V-polarization
H-plane 1710-2170 MHz
Horizontal pattern V-polarization
E-plane 1710-2170 MHz
Vertical pattern V-polarization
738 445, 738 446
Order Information
Model Description
738 445 Antenna with 7-16 DIN connector
738 446 Antenna with N connector
Specications:
Frequency range 790960 MHz
17102170 MHz
Gain 790960 MHz 5 dBi
17101880 MHz 5.5 dBi
18802170 MHz 6.5 dBi
Impedance 50 ohms
VSWR 790806 MHz < 2.2:1
806824 MHz < 1.7:1
824960 MHz < 1.5:1
17102170 MHz < 1.5:1
Polarization Vertical
Maximum input power 200 watts (at 50C)
Connector N or 7-16 DIN female
Weight 1.8 lb (.8 kg)
Dimensions 15.7 x 7.4 x 2.2 inches
(400 x 188 x 55 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 6 lbf / 15 lbf / 8 lbf
(25 N) / (65 N) / (35 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 16.6 x 8.3 x 3.7 inches
(422 x 212 x 95 mm)
Shipping weight 2.6 lb (1.2 kg)
790960 MHz
17102170 MHz
5 dBi gain 806960 MHz
5.5 dBi gain 17101880 MHz
6.5 dBd gain 18802170 MHz
V-POL
14.6 inches
(371 mm)
2.2 inches
(55 mm)
15.7 inches
(400 mm)
7.4 inches
(188 mm)
Mounting Equipment:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(optional) (50 to 145 mm) OD mast.
Wall mounting using customer supplied hardware.
Reference the Mechanical Accessories section.
216
7902690 MHz Wideband LogPeriodic Antenna
V Polarization
7902690 MHz
11 dBi gain 7901000 MHz
11.3 dBi gain 10001700 MHz
11.5 dBd gain 17002690 MHz
V-POL
11286-A
936.3956/b
Mounting
30.9 inches
(785 mm)
11.8 inches
(300 mm)
6.1 inches
(155 mm)
Specications:
Frequency range 7902690 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization Vertical
Connector 7-16 DIN female
Weight 12.1 lb (5.5 kg)
Dimensions 30.9 x11.8 x 6.1 inches
(785 x 300 x 155 mm)
Wind load at 93 mph (150kph)
Front/Side/Rear 5 lbf / 59 lbf / 7 lbf
(20 N) / (260 N) / (30 N)
Wind survival rating 120 mph (200 kph)
Shipping dimensions 39.37 x 14.2 x 6.9 inches
(1000 x 360 x 175 mm)
Shipping weight 13.7 lb (6.2 kg)
Mounting Hardware included for masts of
1.25 to 2.75 inch (30 to 70 mm) OD.
742 192V01
Specications: 790960 MHz 9601710 MHz 17102200 MHz 22002490 MHz 24902690 MHz
Gain 10.8 dBi 11 dBi 11.2 dBi 11 dBi 10.8 dBi
Horizontal beamwidth 65 (halfpower) 60 (halfpower) 55 (halfpower) 50 (halfpower) 50 (halfpower)
Vertical beamwidth 53 (halfpower) 50 (halfpower) 47 (halfpower) 45 (halfpower) 45 (halfpower)
Front-to-back ratio >25 dB >25 dB >25 dB >22 dB >25 dB
Input power maximum 300 watts (at 50C) 250 watts (at 50C) 200 watts (at 50C) 170 watts (at 50C) 150 watts (at 50C)
total 500 watts
E-Plane
Vertical pattern
Vertical - polarization
H-Plane
Horizontal pattern
Vertical - polarization
7901000 MHz
E-Plane
Vertical pattern
Vertical - polarization
H-Plane
Horizontal pattern
Vertical - polarization
17002690 MHz
E-Plane
Vertical pattern
Vertical - polarization
H-Plane
Horizontal pattern
Vertical - polarization
10001700 MHz
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
0o
3
0
o
6
0
o
90o
1
2
0
o
1
5
0
o
180o 2
1
0
o
2
4
0
o
270o
3
0
0
o
3
3
0
o
3
10
20
30
Mounting Clamps Included
217
806 to 960 MHz Yagi Antennas
H or V Polarization
TY-840, TY-860, TY-900
806869 MHz
824894 MHz
890960 MHz
12 dBi gain
H-POL
or
V-POL
(Shown vertically polarized)
8.375 inches
(213 mm)
maximum
24.5 inches
(622 mm)
maximum
Specications: TY-840 TY-860 TY-900
Frequency range 806869 MHz 824894 MHz 890960 MHz
Gain 12 dBi 12 dBi 12 dBi
Impedance 50 ohms 50 ohms 50 ohms
VSWR < 1.5:1 maximum < 1.5:1 maximum < 1.5:1 maximum
(1.35:1 typical) (1.35:1 typical) (1.35:1 typical)
Polarization Horizontal or vertical Horizontal or vertical Horizontal or vertical
Front-to-back ratio >18 dB >18 dB >20 dB
Maximum input power 100 watts (at 50C) 100 watts (at 50C) 100 watts (at 50C)
H-plane beamwidth 59 degrees (half-power) 59 degrees (half-power) 48 degrees (half-power)
E-plane beamwidth 48 degrees (half-power) 48 degrees (half-power) 40 degrees (half-power)
Connector N female N female N female
Weight 2.9 lb (1.3 kg) 3 lb (1.4 kg) 3 lb (1.4 kg)
Dimensions 24.5 x 8.375 inches 24.25 x 8 inches 23 x 7 inches
(622 x 213 mm) (616 x 203 mm) (584 x 178 mm)
Wind load at 93 mph (150kph)
Front/Side 3 lbf / 4 lbf 3 lbf / 4 lbf 3 lbf / 4 lbf
(11 N) / (17 N) (11 N) / (17 N) (11 N) / (17 N)
Wind survival rating 120 mph (200 kph) 120 mph (200 kph) 150 mph (240 kph)
Shipping dimensions 28 x 10 x 4.5 inches 28 x 10 x 4.5 inches 28 x 10 x 4.5 inches
(710 x 254 x 114 mm) (710 x 254 x 114 mm (710 x 254 x 114 mm)
Shipping weight 5.0 lb (2.3 kg) 5.0 lb (2.3 kg) 5.0 lb (2.3 kg)
10060-D
10065-D
10061-D
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
TY-840 TY-900 TY-860
Mounting Information
Description
For masts of 1.25 to 2.375 inch (32 to 60 mm) OD.
Order Information:
Model Description
TY-840 Yagi antenna 806869 MHz
TY-860 Yagi antenna 824894 MHz
TY-900 Yagi antenna 890960 MHz
Mounting Clamps Included
218
Mounting Equipment:
Model Description
MKPS-1 Mounting Kit for 2.375 inch
(optional) (60 mm) OD mast.
MKPS-2 Mounting Kit for 2.875 inch
(optional) (73 mm) OD mast.
MKPS-3 Mounting Kit for 3.5 inch
(optional) (89 mm) OD mast.
MKPS-4 Mounting Kit for 4 inch
(optional) (102 mm) OD mast.
MKPS-5 Mounting Kit for 4.5 inch
(optional) (114 mm) OD mast.
Mounting Hardware Kit Required.
806 to 960 MHz Radome Protected Yagi Antenna
H or V Polarization
RY-840B, RY-860B, RY-900B
806869 MHz
824894 MHz
890960 MHz
12 dBi gain
H-POL
or
V-POL
(Shown vertically polarized)
12 inches
(305 mm)
17 inches
(432 mm)
29 inches
(737 mm)
Specications: RY-840B RY-860B RY-900B
Frequency range 806869 MHz 824894 MHz 890960 MHz
Gain 12 dBi 12 dBi 12 dBi
Impedance 50 ohms 50 ohms 50 ohms
VSWR < 1.5:1 maximum < 1.5:1 maximum < 1.5:1 maximum
(1.35:1 typical) (1.35:1 typical) (1.35:1 typical)
Polarization Horizontal or vertical Horizontal or vertical Horizontal or vertical
Front-to-back ratio >18 dB >18 dB >20 dB
Maximum input power 100 watts (at 50C) 100 watts (at 50C) 100 watts (at 50C)
H-plane beamwidth 58 degrees (half-power) 58 degrees (half-power) 48 degrees (half-power)
E-plane beamwidth 48 degrees (half-power) 44 degrees (half-power) 40 degrees (half-power)
Connector N female N female N female
Weight 16.0 lb (7.3 kg) 16.0 lb (7.3 kg) 16.0 lb (7.3 kg)
Dimensions 29 x 17 x 12 inches 29 x 17 x 12 inches 29 x 17 x 12 inches
(737 x 432 x 305 mm) (737 x 432 x 305 mm) (737 x 432 x 305 mm)
Wind load at 93 mph (150kph)
Side/Top/Rear 63 lbf / 16 lbf / 37 lbf 63 lbf / 16 lbf / 37 lbf 63 lbf / 16 lbf / 37 lbf
(279 N) / (69 N) / (164 N) (279 N) / (69 N) / (164 N) (279 N) / (69 N) / (164 N)
Wind survival rating 120 mph (200 kph) 120 mph (200 kph) 120 mph (200 kph)
Shipping dimensions 31 x 20 x 14.5 inches 31 x 20 x 14.5 inches 31 x 20 x 14.5 inches
(787 x 508 x 368 mm) (787 x 508 x 368 mm) (787 x 508 x 368 mm)
Shipping weight 28.0 lb (12.7 kg) 28.0 lb (12.7 kg) 28.0 lb (12.7 kg)
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
H-plane
Horizontal pattern V-polarization
Vertical pattern H-polarization
E-plane
Horizontal pattern H-polarization
Vertical pattern V-polarization
RY-840B RY-900B RY-860B
Order Information:
Model Description
RY-840B Yagi antenna 806869 MHz
RY-860B Yagi antenna 824894 MHz
RY-900B Yagi antenna 890960 MHz
Top
Side
10057-H
10058-H
10064-H
219
806896 MHz
890960 MHz
940960 MHz
18 dBi gain
H-POL
or
V-POL
PARAFLECTOR
Gain 10 dBi
902928 MHz
H - POL
0 Electrical Downtilt
840 10250
The Kathrein-Scala 840 10250 Paraslot
antenna is specically
designed for spread spectrum systems and other applications
in the 902928 MHz ISM band, featuring high gain and an offset
omnidirectional pattern.
The H- pol ar i zed 840 10250 pr ovi des i sol at i on f r om
co-channel and adjacent-channel V-polarized signals. The
Kathrein-Scala Paraslot design used in these antennas has earned
a reputation for high performance and reliability in thousands of
low-power UHF-TV broadcast transmission systems during the
past 25 years.
83.9 inches
(2131 mm)
2.6 in (65 mm)
23.7 inches
(602 mm)
The top mounting bracket should be
located approximately 2 in. (51 mm)
below the radome collar. The bottom
mounting bracket should be located
approximately 4 in. (102 mm) above
the bottom of the antenna.
Radome collar
234
H-plane
Vertical pattern
H-polarization
2 electrical downtilt
E-plane
Horizontal pattern
H-polarization
Specications:
Frequency range 902928 MHz
Gain 13.4 dBi (maximum)
Impedance 50 ohms
VSWR < 1.35:1
Polarization Horizontal
Maximum input power 300 watts (at 50c)
H-plane beamwidth 5.8 degrees (half-power)
Electrical downtilt 2 degrees (other values optional)
Connector N female
Weight 26 lb (11.8 kg)
Height 180.25 inches (4578 mm)
Diameter 2.375 inches (60 mm)
Wind load at 93 mph (150kph)
Side 64 lbf (283 N)
Wind survival rating 100 mph (161 kph)
Shipping dimensions 190 x 6 x 6 inches
(4826 x 152 x 152 mm)
Shipping weight 48.0 lb (21.8 kg)
10059-J
Mounting Equipment:
Model Description
MKPS-13 Mounting Kit for mounting to a at plate
(optional)
MKPP-23 Mounting Kit for 2.375 to 3.5 inch
(optional) (60 to 89 mm) OD mast.
MKGK-1 Guy Kit
(optional)
MKSK-1 Spreader Kit
(optional)
See Mechanical Accessories Section for more mounting information.
Kathrein Scala Division recommends that this antenna be
secured from the top in addition to the standard bottom
mounting. Contact Kathrein Scala Division Engineering
for assistance.
180.25 inches
(4578 mm)
2.375 in (60 mm)
SL11-915/DT2
PARASLOT
Antenna
H Polarization
The Kathrein-Scala SL11-915/DT2 Paraslot antenna is
specically designed for spread spectrum systems and
other applications in the 902928 MHz ISM band, featuring
high gain and an offset omnidirectional pattern.
PARASLOT is a registered trademark of Kathrein Inc., Scala Division.
235
10072-J
Specications:
Frequency range 928953 MHz
Gain 13.4 dBi (maximum)
Impedance 50 ohms
VSWR < 1.35:1
Polarization Horizontal
Maximum input power 300 watts (at 50c)
H-plane beamwidth 5.8 degrees (half-power)
Electrical downtilt 2 degrees (other values optional)
Connector N female
Weight 25.0 lb (11.3 kg)
Height 156.25 inches (3969 mm)
Diameter 2.375 inches (60 mm)
Wind load at 93 mph (150kph)
Side 54 lbf (240 N)
Wind survival rating 100 mph (161 kph)
Shipping dimensions 167 x 7 x 6 inches
(4242 x 178 x 152 mm)
Shipping weight 35 lb (15.9 kg)
H-plane
Vertical pattern
H-polarization
2 electrical downtilt
E-plane
Horizontal pattern
H-polarization
156.25 inches
(3969 mm)
2.375 in (60 mm)
928953 MHz Omnidirectional PARASLOT
Antenna
H Polarization
The Kathrein-Scala SL11-940/DT2 Paraslot antenna is specically
designed as a central-station antenna for MAS systems operating
in the 928953 MHz band, featuring high gain and an offset
omnidirectional pattern.
PARASLOT is a registered trademark of Kathrein Inc., Scala Division.
Mounting Equipment:
Model Description
MKPS-13 Mounting Kit for mounting to a at plate
(optional)
MKPP-23 Mounting Kit for 2.375 to 3.5 inch
(optional) (60 to 89 mm) OD mast.
MKGK-1 Guy Kit
(optional)
MKSK-1 Spreader Kit
(optional)
See Mechanical Accessories Section for more mounting information.
Kathrein Scala Division recommends that this antenna be secured
from the top in addition to the standard bottom mounting.
Contact Kathrein Scala Division Engineering
for assistance.
SL11-940/DT2
PARASLOT
s
,
F
i
l
t
e
r
s
,
E
l
e
c
t
r
i
c
a
l
A
c
c
e
s
s
o
r
i
e
s
E L E C T R I C A L
K
athrein offers an extensive line of filter products for wireless
applications, including hybrids, milled filters, duplexers, ferrites, power
dividers and taps, diplexers/combiners, and high performance tower
mounted amplifiers, virtually every electrical accessory needed to satisfy
both everyday design problems and special circumstance issues is
available.
From difficult to routine, Kathrein has the right filter to give maximum
performance.
252
Couplers
Frequency Range Maximum Input Power Model Page
8002200 MHz < 100 W 793 555 - 3 dB Coupler with Cable Absorber 300
8001900 MHz < 350 W 792 964, 792 965 - 6 dB Couplers 297
792 966, 792 967 - 10 dB Couplers
806960 MHz < 500 W 793 506 - 3 dB Coupler (90 Hybrid) 295
8002200 MHz < 300 W 793 554 - 3 dB Coupler (90 Hybrid) 298
806960 MHz < 500 W K637061, K637067 - 3 dB Couplers (90 Hybrid) 294
806960 MHz < 350 W 792 937, 792 170 - 4.7 dB Couplers 296
793 105, 792 180 - 6 dB Couplers
793 106, 793 107 - 7 dB Couplers
793 108, 790 213 - 10 dB Couplers
1700-2200 MHz < 300 W 793 006 - 3 dB Coupler 299
1700-2200 MHz < 150 W 792 702 - 3 dB Coupler with Cable Absorber 301
Frequency Range Model Page
806-960 MHz 728 044, 729 812 - Decoupled Power Splitters 302
806960 MHz K6373621 - Hybrid Ring Junction 303
890960 MHz 790 881 - Hybrid Ring Junction 303
1710-1880 MHz 791 498 - Hybrid Ring Junction 303
0 to 4000 MHz 50 Ohm RF Loads (various power ratings and frequency ranges) 305
1575.42 MHz, L1-signal 860 10142 - Low Noise GPS Amplier 284
Power Splitters, Hybrid Ring Junctions, 50 Ohm Loads, GPS Amplier
Filters
Frequency Range Maximum Input Power Model Page
15501700 / 17001900 MHz < 15 W 791 594, 791 397 - Band-Stop Filter 290
18002000 MHz < 15 W 791 398 - Bandpass Filter 292
18002000 MHz < 25 W 792 219 - Band-Stop Filter 293
253
Dual Tower Mount Amplier
PCS/PCS/12 dB
Rx Characteristics:
Frequency range 18501910 MHz
Bandwidth 60 MHz
Loss in bypass mode 2.8 dB (typical)
Return loss > 18 dB (DC ON)
> 15 dB (DC OFF)
Gain -40 +65 C 12 1.3 dB
+22 +28 C 12 0.7 dB
Noise gure -40 +65 C <2.2 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
+22 +28 C <1.7 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
Output 1-dB compression point >15 dBm
3rd order intercept point (OIP3) >25 dBm
Dual
Tower Mount Amplier
782 10811
Ant 0
Ant 1
BTS 0
BTS 1
Double unit for easy use with XPol antennas
Kathrein redundancy amplier design for improved system reliability
By-pass mode to ensure cell operation in case of DC power down
Built-in lightning protection
Compact size
DTMA AISG feed via BTS 0 port or BTS 1 port for both TMAs
AISG DC supply either through one of the ports BTS 0 or BTS 1,
or simultaneously through both ports BTS 0 and BTS 1
Current Window Alarm DC supply feed via BTS 0 (TMA 0) and BTS 1 (TMA 1)
Environmental Characteristics:
Operating temperature range -40 +65C
IP rating IP 67*
MTBF >1,000,000 hours (per TMA)
EMC ETS 300 342-3
Lightning protection 5 kA, 8/20 s RF connections and AISG port
Tx Characteristics:
Frequency range 19301990 MHz
Bandwidth 60 MHz
Insertion loss < 0.5 dB over the middle 80% of BW
a further 0.25 dB over the remaining BW
Input power < 160 W (+52 dBm) CW
<1.6 kW (+62 dBm) Peak
Intermodulation products in Rx band < -160 dBc (3
rd
order; with 2 x 20 W)
Return loss >18 dB
DC and Alarm Characteristics: CWA-Mode AISG-Mode
DC supply 915 V 930 V
Operating current per TMA 80-130 mA 95 mA 9 V (nominal)
without RET 35 mA at 30 V (nominal)
Alarm management 170200 mA AISG 1.1/2.0
Modem characteristics AISG 1.1/2.0
(data rate 9.6 kb)
Mechanical Characteristics:
Material Aluminum housing
Connectors
RF 7-16 DIN female, long neck
AISG connector 8 pin female, IEC 60130-9*
(compliance AISG 1.1/2.0) (Pin 6: 9 30 V DC, pin 3: RS485B,
pin 5: RS485A, pin 7: DC return;
other pins: Not connected)
Mounting Wall mounting with 4 screws (8mm max.)
Mast mounting with optional clamp set.
Weight approx. 11 lb (5 kg)
Dimensions (without connectors 10.9 x 6.5 x 3.1 inches
or mounting brackets) (278 x 166 x 77.5 mm)
Shipping dimensions 19.8 x 10.3 x 8.4 inches
(502 x 262 x 214 mm)
* The DTMA is not designed for permanent operation under water.
Test conditions for the IP67 rating: submerge depth: 1 m; submerge time: 24 hours 11089-FROa
936.A2553
RET Remote Electrical Tilt
AISG Antenna Interface Standards Group
CWA Current Window Alarm
TMA TMA
PCS BTS 0 PCS BTS 1
PCS Ant 0 PCS Ant 1
254
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mast mounting with optional clamp set above.
Wall mounting with 4 screws (8mm max.)
See Mechanical Accessories section for more information.
782 10811
M8 x 10
Grounding screw
BTS ANT
Dual Tower Mount Amplier
PCS/PCS/12 dB
15.9 inches
(405 mm)
6.8 inches
(172 mm)
3.9 inches
(99 mm)
255
Fullband Duplex
Tower Mount Amplier
782 10601
* The DTMA is not designed for permanent operation under water.
Test conditions for the IP67 rating: submerge depth: 1 m; submerge time: 24 hours
Kathrein redundancy amplier design for improved system reliability
Built-in lightning protection
Compact size
Suitable for antenna RET control according to AISG standard
10957-A
936.A2404/b
Fullband Duplex Tower Mount Amplier
PCS/AWS/12 dB
Tx Characteristics: PCS AWS
Frequency range 19301990 MHz 21102155 MHz
Bandwidth 60 MHz 45 MHz
Insertion loss < 0.5 dB over the middle 80% of BW < 0.3 dB
a further 0.25 dB over the remaining BW
Ripple 0.2 0.1
Input power < 200 W (+53 dBm) < 200 W (+53 dBm)
Intermodulation products in Rx band < 160 dBc (3
rd
order; with 2 x 20 W) < 160 dBc (3
rd
order; with 2 x 20 W)
Return loss 18 dB 18 dB
Rx Characteristics: PCS AWS
Frequency range 18501910 MHz 17101755 MHz
Bandwidth 60 MHz 45 MHz
Return loss 18 dB 18 dB
Gain -40 +65 C 12 1.3 dB 12 1 dB
+22 +28 C 12 0.7 dB 12 0.35 dB
Noise gure -40 +65 C < 2.1 dB over the middle 80% of BW < 1.3 dB
a further 0.3 dB over the remaining BW
+22 +28 C < 1.6 dB over the middle 80% of BW < 1 dB
a further 0.3 dB over the remaining BW
Output 1-dB compression point >15 dBm >15 dBm
3rd order intercept point (OIP3) >25 dBm >25 dBm
Mechanical Characteristics:
Material Aluminum housing
Connectors RF 7-16 DIN female long neck
AISG connector 8-pin female, IEC 60130-9 (AISG)
(Compliance AISG) (Pin 3: RS485B, pin 5: RS485A, pin 6: +24 VDC nominal,
pin 7: DC return; other pins: NC)
Mounting Wall mount with 4 screws (max. 8mm dia.)
Mast mount with optional clamp set
Weight 11 lb (5 kg)
Dimensions 10.9 x 6.5 x 3.1 in (278 x 166 x 77.5 mm)
Shipping dimensions 19.8 x 10.3 x 8.4 in (502 x 262 x 214 mm)
Environmental Characteristics:
Operating temperature range -40 +65C
IP rating IP 67*
MTBF >1,000,000 hours (per TMA)
EMC ETS 300 342-3
DC and Alarm Characteristics:
DC supply without RET +10 +30 VDC (negative ground)
Operating current PCS 100 20 mA (+10 +15 VDC)
AWS < 200 mA
Alarm management PCS CWA, > 180 mA
AWS AISG
Modem characteristics According to AISG standard 1.1
(data rate: 9.6 kB)
PCS BTS
PCS Ant
AWS Ant
AWS BTS
256
782 10601
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mast mounting with optional clamp set above.
Wall mounting with 4 screws (8mm max.)
Must be mounted with the AISG connector at the bottom.
See Mechanical Accessories section for more information.
Fullband Duplex Tower Mount Amplier
PCS/AWS/12 dB
Node B
M8 x 10
Grounding screw
BTS ANT
AISG
Connector
3.9 in
(98.7 mm)
6.8 in
(172 mm)
15.9 in
(404.5 mm)
257
Fullband Duplex
Tower Mount Amplier
782 10606
11077-FROa
936.A2552
Environmental Characteristics:
Operating temperature range -40 +65C
IP rating IP 67
MTBF >1,000,000 hours (per TMA)
EMC ETS 300 342-3
Lightning protection 5 kA, 8/20 s RF connections and AISG port
Tx Characteristics AWS DTMA:
Frequency range 21102155 MHz
Bandwidth 45 MHz
Insertion loss < 0.3 dB
Ripple 0.1
Input power < 200 W (+53 dBm)
Intermodulation products in Rx band < -160 dBc (3
rd
order; with 2 x 20 W)
Return loss 18 dB
Rx Characteristics AWS DTMA:
Frequency range 17101755 MHz
Bandwidth 45 MHz
Gain -40 +65 C 12 1 dB
+22 +28 C 12 0.35 dB
Return loss 18 dB
Noise gure -40 +65 C < 1.3 dB
+22 +28 C < 1 dB
Output 1-dB compression point >15 dBm
3rd order intercept point (OIP3) >25 dBm
DC and Alarm Characteristics: CWA Mode AISG Mode
DC supply 915V 930V
Operating current per TMA 80130 mA Nom. 95 mA at 9V
without RET Nom. 35 mA at 30V
Alarm management 170200 mA AISG 1.1/2.0
Modem characteristics AISG 1.1/2.0
(Data rate: 9.6 kB)
Mechanical Characteristics:
Material Aluminum housing
Connectors
RF 7-16 DIN female, long neck
AISG connector 8 pin female, IEC 60130-9*
(compliance AISG 1.1/2.0) (Pin 6: 9 30 V DC, pin 3: RS485B,
pin 5: RS485A, pin 7: DC return;
other pins: Not connected)
Weight 11 lb (5 kg)
Dimensions (without connectors 10.9 x 6.5 x 3.1 inches
or mounting brackets) (278 x 166 x 77.5 mm)
* The DTMA is not designed for permanent operation under water.
Test conditions for the IP67 rating: submerge depth: 1 m; submerge time: 24 hours
Fullband Duplex Tower Mount Amplier
AWS/AWS/12 dB
Double unit for easy use with XPol antennas
Kathrein redundancy amplier design for improved system reliability
Built-in lightning protection
Compact size
Suitable for antenna RET control according to AISG standard
DTMA AISG feed via BTS 0 port or BTS 1 port for both TMAs
AISG DC supply either through one of the ports BTS 0 or BTS 1, or simultaneously
through both ports BTS 0 and BTS 1
CWA DC supply feed via BTS 0 (TMA 0) and BTS 1 (TMA 1)
AWS BTS 0
AWS BTS 1
AWS Ant 0
AWS Ant 1
AWS ANT 0 AWS ANT 1
AWS BTS 0 AWS BTS 1
258
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mast mounting with optional clamp set above.
Wall mounting with 4 screws (8mm max.)
See Mechanical Accessories section for more information.
782 10606
Fullband Duplex Tower Mount Amplier
AWS/AWS/12 dB
M8 x 10
Grounding screw
BTS ANT
15.9 inches
(405 mm)
6.8 inches
(172 mm)
Must be mounted with the AISG
connector at the bottom.
3.9 inches
(99 mm)
259
Dual Tower Mount Amplier
PCS/PCS/24 dB
Rx Characteristics:
Frequency range 18501910 MHz
Bandwidth 60 MHz
Loss in bypass mode 2.8 dB (typical)
Return loss > 18 dB (DC ON)
> 15 dB (DC OFF)
Gain -40 +65 C 24 1.2 dB
+22 +28 C 24 0.6 dB
Noise gure -40 +65 C <2.1 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
+22 +28 C <1.6 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
Output 1-dB compression point >19 dBm
3rd order intercept point (OIP3) >28 dBm
Dual
Tower Mount Amplier
782 10401
Ant 0
Ant 1
BTS 0
BTS 1
Double unit for easy use with XPol antennas
Kathrein redundancy amplier design for improved system reliability
By-pass mode to ensure cell operation in case of TMA (Alarm 2) or DC power down
Alarm management: Supports 2 alarm levels
Alarm 1: One LNA of the balanced circuit failed
Alarm 2: Both LNAs of the balanced circuit failed
Automatically switched to bypass mode
Built-in lightning protection
Compact size
DTMA DC supply and alarming separately via BTS 0 repectively BTS 1 port
Environmental Characteristics:
Operating temperature range -40 +65C
IP rating IP 67*
MTBF >1,000,000 hours (per TMA)
EMC ETS 300 342-3
Lightning protection 5 kA, 8/20 s pulse
Tx Characteristics:
Frequency range 19301990 MHz
Bandwidth 60 MHz
Insertion loss < 0.5 dB over the middle 80% of BW
a further 0.25 dB over the remaining BW
Input power < 160 W (+52 dBm) CW
<1.6 kW (+62 dBm) Peak
Intermodulation products in Rx band < -117 dBm (2 Tx carriers at +43 dBm)
Return loss >18 dB
DC and Alarm Characteristics:
DC supply +12V nominal (7.515V, minus grounded)
Typically 230 mA per TMA
Alarm management Current window alarm handling
Alarm current Ia Alarm 1: Ia > 310 mA
Alarm 2: Ia > 500 mA
Mechanical Characteristics:
Material Aluminum housing
RF connectors 7-16 DIN female
Mounting Wall mounting with 4 screws (8mm max.)
Mast mounting with optional clamp set.
Weight 11 lb (5 kg)
Dimensions 10.9 x 6.5 x 3.1 inches
(278 x 166 x 77.5 mm)
Shipping dimensions 19.8 x 10.3 x 8.4 inches
(502 x 262 x 214 mm)
* The DTMA is not designed for permanent operation under water.
Test conditions for the IP67 rating: submerge depth: 1 m; submerge time: 24 hours
BTS 0 BTS 1
Ant 1 Ant 0
DTMA
10934-A
936.2937/b
260
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mast mounting with optional clamp set above.
Wall mounting with 4 screws (8mm max.)
See Mechanical Accessories section for more information.
782 10401
Dual Tower Mount Amplier
PCS/PCS/24 dB
M8 x 10
Grounding screw
BTS ANT
15.9 inches
(405 mm)
6.8 inches
(172 mm)
3.9 inches
(99 mm)
261
Dual
Tower Mount Amplier
782 10404
10753-D
936.2939/c
$4-!
Ant 0 Ant 1
Node B0 Node B1
Environmental Characteristics:
Operating temperature range -40 +65C
IP rating IP 67*
MTBF >1,000,000 hours (per TMA)
EMC ETS 300 342-3
Lightning protection 5 kA, 8/20s RF connections and AISG port
Tx Characteristics:
Frequency range 19301990 MHz
Bandwidth 60 MHz
Insertion loss < 0.5 dB over the middle 80% of BW
a further 0.25 dB over the remaining BW
Input power < 160 W (+52 dBm) CW
<1.6 kW (+62 dBm) Peak
Intermodulation products in Rx band < -117 dBm (2 Tx carriers at +43 dBm)
Return loss >18 dB
Rx Characteristics:
Frequency range 18501910 MHz
Bandwidth 60 MHz
Loss in bypass mode <2.8 dB (typical)
Return loss > 18 dB (DC ON)
> 15 dB (DC OFF)
Gain -40 +65 C 24 1.2 dB
+22 +28 C 24 0.6 dB
Noise gure -40 +65 C <2.1 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
+22 +28 C <1.6 dB over the middle 80% of BW
a further 0.3 dB over the remaining BW
Output 1-dB compression point >19 dBm
3rd order intercept point (OIP3) >28 dBm
Double unit for easy use with XPol antennas
Kathrein redundancy amplier design for improved system reliability
By-pass mode to ensure cell operation in case of DC power down
Built-in lightning protection
Compact size
Suitable for antenna RET control according to AISG standard
DTMA DC supply and AISG feed via BTS 0 port for both TMAs
DC and Alarm Characteristics: Through Node BO Port only
DC supply +12V nominal (915V, minus grounded)
without RET Typically 250 mA per TMA
Alarm management According to AISG standard 1.1
Modem characteristics According to AISG standard 1.1
Data rate: 9.6 kB
Mechanical Characteristics:
Connectors RF 7-16 DIN female
AISG connector 8-pin female, IEC 60130-9
(compliance AISG 1.1) (Pin 1: +12 V DC nominal, pin 3: RS485B, pin 5: RS485A,
pin 7: DC return; other pins: Not connected)
Weight 11 lb (5 kg)
Dimensions 10.9 x 6.5 x 3.1 inches
(278 x 166 x 77.5 mm)
Shipping dimensions 19.8 x 10.3 x 8.4 inches
(502 x 262 x 214 mm)
Ant 0
Ant 1
Node B0
AISG and
DC-Port
Node B1
* The DTMA is not designed for permanent operation under water.
Test conditions for the IP67 rating: submerge depth: 1 m; submerge time: 24 hours
Dual Tower Mount Amplier
PCS/PCS/24 dB
262
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mast mounting with optional clamp set above.
Wall mounting with 4 screws (8mm max.)
Must be mounted with the AISG connector at the bottom.
See Mechanical Accessories section for more information.
782 10404
BTS ANT
M8 x 10
Grounding screw
15.9 inches
(405 mm)
6.8 inches
(172 mm)
3.3 inches
(83.4 mm)
Must be mounted with the
AISG connector at the bottom.
10.9 inches
(278 mm)
3.1 inches
(77.5 mm)
Dual Tower Mount Amplier
PCS/PCS/24 dB
263
6943800 MHz RF Power dividers 860 1010n Series
6943800 MHz
For outdoor and
indoor applications.
11051-C
936.2956/b
Kathrein Scala Division RF power dividers are designed for use in a number of
professional applications including multi-element antenna arrays and radiating cable
systems and other cases where efcient broadband power splitting is required.
These dividers feature low insertion loss and excellent impedance match. Careful
and conservative mechanical designs assure a long service life with high reliability
and stability in even the most difcult environmental conditions.
Mounting Options:
Model Description
131 1847 Mounting Kit for 2 to 5.7 inch (50 to 145 mm) OD mast.
860 10104
860 10105
860 10105
11.3 inches
(286 mm)
2.4 inches
(61 mm)
11.4 inches
(289 mm)
2.6 inches
(65 mm)
2.1 inches
(54 mm)
2.5 inches
(63 mm)
860 10104
Order Information:
Model Description
860 10100 2-way RF power divider, 200 watts, N female
860 10102 3-way RF power divider, 200 watts, N female
860 10104 4-way RF power divider, 200 watts, N female
860 10101 2-way RF power divider, 700 watts, 7-16 DIN female
860 10103 3-way RF power divider, 700 watts, 7-16 DIN female
860 10105 4-way RF power divider, 700 watts, 7-16 DIN female
Specications:
Frequency range 6943800 MHz 6943800 MHz
Impedance 50 ohms 50 ohms
Insertion loss <0.05 dB <0.05 dB
Split 860 10100 2-way 860 10101 2-way
860 10102 3-way 860 10103 3-way
860 10104 4-way 860 10105 4-way
VSWR <1.3:1 (694894 MHz) <1.3:1 (694894 MHz)
<1.15:1 (7903800 MHz) <1.15:1 (7903800 MHz)
Maximum input power 200 watts (at 50C) 700 watts (at 50C) )
Connector N female 7-16 DIN female
Intermodulation (2x20w) IM3: <-150 dBc IM3: <-150 dBc
Temperature range -55C to +60C -55C to +60C
Weight (max.) 1.7 lb (0.78 kg) 2.1 lb (0.96 kg)
Dimensions (maximum) 11.4 x 2.5 x 2.1 inches 11.3 x 2.6 x 2.4 inches
(289 x 63 x 54 mm) (286 x 65 x 61 mm)
Shipping dimensions 11.8 x 3 x 3 inches 11.8 x 3 x 3 inches
(300 x 75 x 75 mm) (300 x 75 x 75 mm)
Shipping weight 2.7 lb (1.2 kg) 2.9 lb (1.3 kg)
264
790960 MHz RF Power dividers
Equal power splits. Available with 6, 8, 10, or 12-way splits.
Special mounting arrangements for alternate mast sizes, etc.
Please contact Kathrein-Scala sales engineering for information and
pricing on RF power dividers designed for your specic requirements.
PDL Series
* Note: Dimensions shown do not
include connectors.
790960 MHz
Specications: PDL2-55 PDL3-333 PDL4-2222
Frequency range 790-960 MHz 790-960 MHz 790-960 MHz
Impedance 50 ohms 50 ohms 50 ohms
Insertion loss <0.5 dB <0.5 dB <0.5 dB
Split 50%/50% 33.3%/33.3%/33.3% 25%/25%/25%/25%
VSWR <1.2:1 <1.2:1 <1.2:1
Maximum input power 100 watts 100 watts 100 watts
Connector N female N female N female
Weight 2 lb (0.9 kg) 2 lb (0.9 kg) 2.25 lb (1 kg)
Dimensions* 5.6 x 4.6 x 3.25 inches 5.6 x 4.6 x 3.25 inches 5.6 x 4.6 x 3.25 inches
(142 x 117 x 83 mm) (142 x 135 x 83 mm) (142 x 150 x 83 mm)
Special orders with
uneven power splits.
PDL3-333
Order Information:
Model Description
PDL2-55 RF power divider for outdoor & indoor
PDL3-333 RF power divider for outdoor & indoor
PDL4-2222 RF power divider for outdoor & indoor
Mounting Options:
Description
Included for masts of 1.25 to 2.375 inch (32 to 60 mm) OD.
3.25 inches
(83 mm)
5.6 inches
(142 mm)
4
.
6
in
c
h
e
s
(
1
1
7
m
m
)
For outdoor and
indoor applications.
265
Continuously Adjustable RF Indoor Power Tap
790960 MHz
17102500 MHz
Indoor Power Tap
Continuously Adjustable
K63236001, 860 10023
10827-C
936.3914
936.2261/b
Order Information:
Model Description
K63236001 Adjustable indoor power tap
860 10023 Adjustable indoor power tap
Specications: K63236001 860 10023
Frequency range 790960 MHz 870960 MHz
17102170 MHz 17102500 MHz
Power split ratio -5 dB to -15 dB -5 dB to -15 dB
continuously adjustable (75%/25% to 97%/3%) (75%/25% to 97%/3%)
Impedance 50 ohms 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc IM3: <-150 dBc
Insertion loss <0.1 dB <0.1 dB
VSWR <2.1:1 (790824 MHz)
<1.7:1 (824960 MHz) <1.7:1 (870960 MHz)
<1.7:1 (17102170 MHz) <1.7:1 (17102500 MHz)
Maximum input power 100 watts (at 50C) 100 watts (at 50C)
Connector N female N female
Environmental conditions IP 52 IP 52
Weight 1.1 lb (0.5 kg) 1.1 lb (0.5 kg)
Dimensions* 9.3 x 3.9 x 1 inches 10.4 x 3.9 x 1 inches
(235 x 100 x 25 mm) (263 x 100 x 25 mm)
Shipping dimensions 9.8 x 4.4 x 4 inches 10.9 x 4.4 x 1.6 inches
(249 x 111 x 40 mm) (277 x 111 x 40 mm)
Shipping weight 1.5 lb (0.68 kg) 1.5 lb (0.68 kg)
* Excludes connectors.
DC transmission only between input and port P
1
.
P
2
is coupled capacitively.
P
1
Output
P
2
Output
P input
Adjust tap to
desired split ratio
Splitting table:
P
2
:P
1
[dB] P
1
:P
input
[dB] P
2
:P
input
[dB]
-5 -1.2 (75%) -6.2 (25%)
-10 -0.4 (91%) -10.4 (9%)
-15 -0.1 (97%) -15.1 (3%)
266
Scale Power Split
(dB) Ratio (x:1) P1 (%) P2 (%) P1 (dB) P2 (dB)
-5.00 . . . . . . . . . 3.2 . . . . . . . . 76.0% . . . . . . . .24.0% . . . . . . . . -1.2 . . . . . . . . . -6.2
-5.25 . . . . . . . . . 3.3 . . . . . . . . 77.0% . . . . . . . .23.0% . . . . . . . . -1.1 . . . . . . . . . -6.4
-5.50 . . . . . . . . . 3.5 . . . . . . . . 78.0% . . . . . . . .22.0% . . . . . . . . -1.1 . . . . . . . . . -6.6
-5.75 . . . . . . . . . 3.8 . . . . . . . . 79.0% . . . . . . . .21.0% . . . . . . . . -1.0 . . . . . . . . . -6.8
-6.00 . . . . . . . . . 4.0 . . . . . . . . 79.9% . . . . . . . .20.1% . . . . . . . . -1.0 . . . . . . . . . -7.0
-6.25 . . . . . . . . . 4.2 . . . . . . . . 80.8% . . . . . . . .19.2% . . . . . . . . -0.9 . . . . . . . . . -7.2
-6.50 . . . . . . . . . 4.5 . . . . . . . . 81.7% . . . . . . . .18.3% . . . . . . . . -0.9 . . . . . . . . . -7.4
-6.75 . . . . . . . . . 4.7 . . . . . . . . 82.6% . . . . . . . .17.4% . . . . . . . . -0.8 . . . . . . . . . -7.6
-7.00 . . . . . . . . . 5.0 . . . . . . . . 83.4% . . . . . . . .16.6% . . . . . . . . -0.8 . . . . . . . . . -7.8
-7.2 5 . . . . . . . . . 5.3 . . . . . . . . 84.1% . . . . . . . .15.9% . . . . . . . . -0.7 . . . . . . . . . -8.0
-7.50 . . . . . . . . . 5.6 . . . . . . . . 84.9% . . . . . . . .15.1% . . . . . . . . -0.7 . . . . . . . . . -8.2
-7.75 . . . . . . . . . 6.0 . . . . . . . . 85.6% . . . . . . . .14.4% . . . . . . . . -0.7 . . . . . . . . . -8.4
-8.00 . . . . . . . . . 6.3 . . . . . . . . 86.3% . . . . . . . .13.7% . . . . . . . . -0.6 . . . . . . . . . -8.6
-8.25 . . . . . . . . . 6.7 . . . . . . . . 87.0% . . . . . . . .13.0% . . . . . . . . -0.6 . . . . . . . . . -8.9
-8.50 . . . . . . . . . 7.1 . . . . . . . . 87.6% . . . . . . . .12.4% . . . . . . . . -0.6 . . . . . . . . . -9.1
-8.7 5 . . . . . . . . . 7.5 . . . . . . . . 88.2% . . . . . . . . 11.8% . . . . . . . . -0.5 . . . . . . . . . -9.3
-9.00 . . . . . . . . . 7.9 . . . . . . . . 88.8% . . . . . . . . 11.2% . . . . . . . . -0.5 . . . . . . . . . -9.5
-9.25 . . . . . . . . . 8.4 . . . . . . . . 89.4% . . . . . . . .10.6% . . . . . . . . -0.5 . . . . . . . . . -9.7
-9.50 . . . . . . . . . 8.9 . . . . . . . . 89.9% . . . . . . . .10.1% . . . . . . . . -0.5 . . . . . . . . -10.0
-9.75 . . . . . . . . . 9.4 . . . . . . . . 90.4% . . . . . . . . .9.6% . . . . . . . . -0.4 . . . . . . . . -10.2
-10.00 . . . . . . . . 10.0 . . . . . . . . 90.9% . . . . . . . . .9.1% . . . . . . . . -0.4 . . . . . . . . -10.4
-10.25 . . . . . . . . 10.6 . . . . . . . . 91.4% . . . . . . . . .8.6% . . . . . . . . -0.4 . . . . . . . . -10.6
-10.50 . . . . . . . . 11.2 . . . . . . . . 91.8% . . . . . . . . .8.2% . . . . . . . . -0.4 . . . . . . . . -10.9
-10.75 . . . . . . . . 11.9 . . . . . . . . 92.2% . . . . . . . . .7.8% . . . . . . . . -0.4 . . . . . . . . -11.1
-11.00 . . . . . . . . 12.6 . . . . . . . . 92.6% . . . . . . . . .7.4% . . . . . . . . -0.3 . . . . . . . . -11.3
-11.25 . . . . . . . . 13.3 . . . . . . . . 93.0% . . . . . . . . .7.0% . . . . . . . . -0.3 . . . . . . . . -11.6
-11.50 . . . . . . . . 14.1 . . . . . . . . 93.4% . . . . . . . . .6.6% . . . . . . . . -0.3 . . . . . . . . -11.8
-11.75 . . . . . . . . 15.0 . . . . . . . . 93.7% . . . . . . . . .6.3% . . . . . . . . -0.3 . . . . . . . . -12.0
-12.00 . . . . . . . . 15.8 . . . . . . . . 94.1% . . . . . . . . .5.9% . . . . . . . . -0.3 . . . . . . . . -12.3
-12.25 . . . . . . . . 16.8 . . . . . . . . 94.4% . . . . . . . . .5.6% . . . . . . . . -0.3 . . . . . . . . -12.5
-12.50 . . . . . . . . 17.8 . . . . . . . . 94.7% . . . . . . . . .5.3% . . . . . . . . -0.2 . . . . . . . . -12.7
-12.75 . . . . . . . . 18.8 . . . . . . . . 95.0% . . . . . . . . .5.0% . . . . . . . . -0.2 . . . . . . . . -13.0
-13.00 . . . . . . . . 20.0 . . . . . . . . 95.2% . . . . . . . . .4.8% . . . . . . . . -0.2 . . . . . . . . -13.2
-13.25 . . . . . . . . 21.1 . . . . . . . . 95.5% . . . . . . . . .4.5% . . . . . . . . -0.2 . . . . . . . . -13.5
-13.50 . . . . . . . . 22.4 . . . . . . . . 95.7% . . . . . . . . .4.3% . . . . . . . . -0.2 . . . . . . . . -13.7
-13.75 . . . . . . . . 23.7 . . . . . . . . 96.0% . . . . . . . . .4.0% . . . . . . . . -0.2 . . . . . . . . -13.9
-14.00 . . . . . . . . 25.1 . . . . . . . . 96.2% . . . . . . . . .3.8% . . . . . . . . -0.2 . . . . . . . . -14.2
-14.25 . . . . . . . . 26.6 . . . . . . . . 96.4% . . . . . . . . .3.6% . . . . . . . . -0.2 . . . . . . . . -14.4
-14.50 . . . . . . . . 28.2 . . . . . . . . 96.6% . . . . . . . . .3.4% . . . . . . . . -0.2 . . . . . . . . -14.7
-14.75 . . . . . . . . 29.9 . . . . . . . . 96.8% . . . . . . . . .3.2% . . . . . . . . -0.1 . . . . . . . . -14.9
-15.00 . . . . . . . . 31.6 . . . . . . . . 96.9% . . . . . . . . .3.1% . . . . . . . . -0.1 . . . . . . . . -15.1
Continuously Adjustable RF Indoor Power Tap K63236001, 860 10023
267
11246-A
936.3575/a
6942700 MHz RF Indoor Power Tap
6942700 MHz
RF Power Tap
For Indoor Applications
860 10136, 860 10137, 860 10138
Mounting Options:
Description
None needed
For indoor use only.
General specications:
Frequency range 6942700 MHz
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Insertion loss <0.05 dB
VSWR 694790 MHz <2.0:1
7902500 MHz <1.5:1
25002700 MHz <2.0:1
Maximum input power 100 watts (at 50C)
Connector N female
Weight 1.1 lb (0.5 kg)
Dimensions 9.6 x 2.5 x 1 inches
(244 x 64 x 25 mm)
Shipping dimensions 10.5 x 4.4 x 3.7 inches
(267 x 111 x 95 mm
Shipping weight 1.5 lb (0.68 kg)
Mounting None needed
Environmental conditions IP 52
DC transmission only between input and port P
1
.
P
2
is coupled capacitively.
9.6 inches
(244 mm)
2.5 inch
(64 mm)
1 inch
(25 mm)
P1
P2=P1-(6dB)
Capacitive coupled to input
Order Information:
Model Description
860 10136 Indoor power tap
860 10137 Indoor power tap
860 10138 Indoor power tap
Specications: 860 10136 860 10137 860 10138
Tap loss
Input P
1
-1.0 dB
-0.4 dB
-0.1 dB
Input P
2
-7.0 dB
-10.4 dB
-15.1 dB
N
E
W
268
10819-B
936.2248/b
Specications:
Frequency range 6942700 MHz
Impedance 50 ohms
Insertion loss <0.05 dB
Power split ratio
860-10017 50%/50%
860-10018 33.3%/33.3%/33.3%
860-10019 25%/25%/25%/25%
VSWR 694864 MHz 7902500 MHz 25002700
MHz
860-10017 <1.5:1 <1.25:1 <2.0:1
860-10018 <1.5:1 <1.25:1 <2.0:1
860-10019 <1.5:1 <1.3:1 <2.0:1
Intermodulation (2x20w) IM3: <-150dBc
Maximum input power 100 watts
Connector N female
DC capability DC transmission between all terminations
(suitable for remote power supply systems)
Environmental conditions IP 52
Weight 1.3 lb (0.6 kg)
Dimensions 8 x 2.5 x 1.6 inches (maximum)
(204 x 63 x 41 mm)
Shipping dimensions 9.5 x 4.3 x 3.7 inches (maximum)
(242 x 110 x 95 mm)
Mounting For indoor use only. Mounting hardware is not
included.
Kathrein-Scala recommends the use of nylon tie
straps for mounting.
Order Information:
Model Description
860 10017 2-way power divider for indoor use only
860 10018 3-way power divider for indoor use only
860 10019 4-way power divider for indoor use only
860-10019
8 inches
(204 mm)
1 inch
(25 mm)
1 inch
(25 mm)
Mounting Options:
Description
For indoor use only.
Mounting hardware is not included.
Kathrein-Scala recommends the use of nylon tie straps for mounting.
6942700 MHz RF Indoor Power Divider
6942700 MHz
RF Power Divider
For Indoor Applications
860 10017, 860 10018, 860 10019
860 10019
269
Designed for co-siting purposes.
Enables feeder sharing.
Can be used as a combiner near the BTS or in a reciprocal
function near the antenna.
Suitable for indoor or outdoor applications.
Wall or mast mounting.
Available as a single unit or a double unit for X-Pol antennas.
Built-in lightning protection.
DC stop available as an accessory.
Extremely low insertion loss.
High input power.
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit (optional) for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mounts to a at surface with four screws (max. 8 mm dia).
Mounts to 2 to 5.7 inch (50 to 145 mm) OD masts with optional mounting kit.
See Mechanical Accessories section for more information.
380960 MHz
17102700 MHz
Dualband Combiner
11245-A
936.3749
782 10680, 782 10682
782 10681, 782 10683
782 10680, 782 10682
Single Unit
782 10681, 782 10683
Double Unit
Specications: 782 10680 Single Unit 782 10682 Single Unit
782 10681 Double Unit 782 10683 Double Unit
Pass band
Band 1 380960 MHz 380960 MHz
Band 2 17102700 MHz 17102700 MHz
Impedance 50 ohms 50 ohms
VSWR < 1.2:1 (380960 / 17102700) < 1.2:1 (380960 / 17102700)
Insertion loss
Port 1Port 3 <0.1 dB (380960 MHz) <0.1 dB (380960 MHz)
Port 2Port 3 <0.1 dB (17102700 MHz) <0.1 dB (17102700 MHz)
Isolation
Port 1Port 2 > 55 dB (380550 MHz) > 55 dB (380550 MHz)
> 65 dB (550960 MHz) > 65 dB (550960 MHz)
> 65 dB (17102700 MHz) > 65 dB (17102700 MHz)
Input power
Band 1 / Band 2 < 700 watts / <700 watts < 700 watts / < 700 watts
Intermodulation < 160 dBc (3rd order; with 2 x 20 W) < 160 dBc (3rd order; with 2 x 20 W)
Operating temperature -55 to +60 C -55 to +60 C
Connector 7-16 DIN female (long neck) 7-16 DIN female (long neck)
Application Indoor or outdoor (IP 66) Indoor or outdoor (IP 66)
DCAISG transparency
Port 1Port 3 By-pass (2500 mA maximum) Stop
Port 2Port 3 By-pass (2500 mA maximum) By-pass (2500 mA maximum)
Lightning protection 3 kA, 10/350 s pulse 3 kA, 10/350 s pulse
Weight
Single unit 4.9 lb (2.2 kg) 4.9 lb (2.2 kg)
Double unit 9.5 lb (4.3 kg) 9.5 lb (4.3 kg)
Dimensions
Single unit 9.6 x 5 x 2.1 inches (318 x 122 x 67 mm) 9.6 x 5 x 2.1 inches (318 x 122 x 67 mm)
Double unit 9.6 x 5 x 4.3 inches (318 x 122 x 118 mm) 9.6 x 5 x 4.3 inches (318 x 122 x 118 mm)
Shipping dimensions
Single unit 14.4 x 8.1 x 5.9 inches (365 x 207 x 150 mm) 14.4 x 8.1 x 5.9 inches (365 x 207 x 150 mm)
Double unit 14.4 x 8.1 x 8.4 inches (365 x 207 x 214 mm) 14.4 x 8.1 x 8.4 inches (365 x 207 x 214 mm)
380 960 1710 2700 3800 960 1710 1700
N
E
W
270
782 10680, 782 10662
Dualband Combiner
782 10681, 782 10683
4 screws M5 x 12
4.6 inches
(118 mm)
2.6 inches
(67 mm)
4.8 inches
(122 mm)
10.7 inches
(271 mm)
1.6 inches
(41 mm)
1.9 inches
(49 mm)
3.6 inches
(91 mm)
1.6 inches
(41 mm)
1.4 inches
(35 mm)
4 inches
(102 mm)
11.3 inches
(288 mm)
12.5 inches
(318 mm)
1.9 inches
(49 mm)
8.3 inches
(210 mm)
6.9 inches
(176 mm)
2.5 inches
(64 mm)
Typical Attenuation Curves
Diagram II
Port 1 jPort 3 Port 2 jPort 3
Diagram I
Port 1 jPort 3 Port 2 jPort 3
Order Information:
Model Description
782 10680 Single Dualband combiner - By-pass / By-pass
782 10681 Double Dualband combiner - By-pass / By-pass
782 10682 Single Dualband combiner - Stop / By-pass
782 10683 Double Dualband combiner - Stop / By-pass
271
Designed for cable sharing/reduction in PCS and WiMAX
systems.
Can be used as a combiner near the BTS or in a reciprocal function
near the antenna.
Suitable for indoor or outdoor applications.
Wall or mast mounting.
Built-in lightning protection.
External DC stop available as an accessory.
Available as a single unit, or for XPol anten-nas as a double unit
Very low insertion loss.
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit (optional) for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mounts to a at surface with four screws (max. 8 mm dia).
Mounts to 2 to 5.7 inch (50 to 145 mm) OD masts with optional mounting kit.
See Mechanical Accessories section for more information.
470960 MHz
17102700 MHz
Dualband Combiner
11244-A
936.3891
782 10660, 782 10662, 782 10664
782 10661, 782 10663, 782 10665
782 10660, 782 10662, 782 10664
Single Unit
782 10661, 782 10663, 782 10665
Double Unit
Specications:
Pass band
Band 1 470960 MHz
Band 2 17102700 MHz
Impedance 50 ohms
VSWR < 1.2:1 (470960 / 17102700)
Insertion loss
Port 1Port 3 <0.15 dB (470960 MHz) (0.1 dB typical)
Port 2Port 3 <0.2 dB (17102700 MHz) (0.1 dB typical)
Isolation
Port 1Port 2 > 55 dB (470960 MHz)
> 65 dB (17102700 MHz)
Input power
Band 1 / Band 2 < 650 watts / < 350 watts
Intermodulation < 160 dBc (3rd order; with 2 x 20 W)
Operating temperature -55 to +60 C
Connector 7-16 DIN female (long neck)
Application Indoor or outdoor (IP 66)
DCAISG transparency 782 10660 Single Unit 782 10662 Single Unit 782 10664 Single Unit
782 10661 Double Unit 782 10663 Double Unit 782 10665 Double Unit
Port 1Port 3 By-pass (2500 mA maximum) Stop By-pass (2500 mA maximum)
Port 2Port 3 By-pass (2500 mA maximum) By-pass (2500 mA maximum) Stop
Lightning protection 3 kA, 10/350 s pulse
Weight
Single unit 2.6 lb (1.2 kg
Double unit 5.3 lb (2.4 kg)
Dimensions without connectors or mounting brackets
Single unit 5.7 x 5 x 1.5 inches (145 x 126 x 38 mm)
Double unit 5.7 x 5 x 3.7 inches (145 x 126 x 93 mm)
Shipping dimensions
Single unit 11.2 x 6.2 x 3.7 inches (285 x 157 x 93 mm)
Double unit 11,2 x 6.2 x 5.8 inches (285 x 157 x 148 mm)
470 960 1710 2700 470 960 1710 2700 470 960 1710 2700
N
E
W
272
782 10660, 782 10662, 782 10664 Dualband Combiner
782 10661, 782 10663, 782 10665
Order Information:
Model Description
782 10660 Single Dualband combiner - By-pass / By-pass
782 10661 Double Dualband combiner - By-pass / By-pass
782 10662 Single Dualband combiner - Stop / By-pass
782 10663 Double Dualband combiner - Stop / By-pass
782 10664 Single Dualband combiner - By-pass / Stop
782 10665 Double Dualband combiner - By-pass / Stop
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1710 2700
0 300 600 900 1200 1500 1800 2100 2400 2700 3000
470 960
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1.0
0 300 600 900 1200 1500 1800 2100 2400 2700 3000
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1710 2700 470 960
Typical Attenuation Curves
Diagram II
Port 1 jPort 3 Port 2 jPort 3
Diagram I
Port 1 jPort 3 Port 2 jPort 3
Side view
Single Unit
Top view
Single Unit,
Double Unit
Side view
Double Unit
3.7 inches
(93 mm)
2.1 inches
(53 mm)
5 inches
(126 mm)
8.1 inches
(206 mm)
5.7 inches
(145 mm)
1.4 inches
(35 mm)
1.5 inches
(38 mm)
2.2 inches
(55 mm)
0.8 inches
(21 mm)
1.4 inches
(35 mm)
4.6 inches
(40 mm)
2.4 inches
(60 mm)
8.8 inches
(224 mm)
9.6 inches
(244 mm)
273
Designed for co-siting purposes.
Enables feeder sharing.
Suitable for indoor or outdoor applications (IP 66).
DC pass through between all ports.
External DC Stop available as an accessory.
782 10809
Single unit
782 10809, 782 10810
Order Information:
Model Description
782 10809 Dualband combiner, single unit
782 10810 Dualband combiner, double unit
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit (optional) for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mounts to a at surface with four screws (max. 8 mm dia).
See Mechanical Accessories section for more information.
18501910/19301990 MHz
17101755/21102155 MHz
Dualband Combiner
11069-A
936.3344
Specications:
Pass band
PCS 18501910 (Rx) / 19301990 (Tx) MHz
AWS 17101755 (Rx) / 21102155 (Tx) MHz
Impedance 50 ohms
VSWR < 1.25:1 (18501910 / 19301990 MHz)
< 1.25:1 (17101755 / 21102155 MHz)
Insertion loss
Port PCSPort ANT <0.3 dB (18501910 / 19301990 MHz)
Port AWSPort ANT <0.2 dB (17101755 / 21102155 MHz)
Insolation
Port PCSPort AWS > 50 dB (18501910 / 19301990 MHz)
> 50 dB (17101755 / 21102155 MHz)
Input power
Port PCS < 250 watts (18501910 / 19301990 MHz)
Port AWS < 250 watts (17101755 / 21102155 MHz)
Intermodulation < -160 dBc (3rd order; with 2 x 20 W)
Operating temperature -40 to +65 C
Connectors 7-16 DIN female (long neck)
Application Indoor or outdoor (IP 66)
Lightning protection 3 kA, 10/350 s
DC/AISG transparency By-pass between all ports (max. 2500 mA)
Weight single unit 5.5 lb (2.5 kg)
double unit 11 lb (5 kg)
Dimensions single unit 11.7 x 4.8 x 2.5 inches (296 x 122 x 64 mm)
double unit 11.7 x 4.8 x 4.7 inches (296 x 122 x 120 mm)
(includes mounting bracket)
Port PCS Port ANT
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1.0
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
2110 2155
1850 1910
1930 1990
1710 1755
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
2110 2155
1850 1910
1930 1990 1710 1755
Typical Attenuation Curves
Port AWS Port ANT
Diagram I
Diagram II
Port Port
PCS ANT
Port Port
AWS ANT
Port Port
AWS ANT
274
782 10809, 782 10810 Dualband Combiner
The mounting plates can be removed and
replaced with other means of mounting by
removing the screws through (M5 x 10).
Caution: Exceeding the maximum drilled
depth of 8.5 mm with replacement
hardware and fasteners may permanently
damage the unit.
~
4 screws M5 x 10
4 spring washers 5.5 DIN 6095
~
4 screws M5 x 10
4 spring washers 5.5 DIN 6095
4.7 inches
(120 mm)
2.5 inches
(64 mm)
4.8 inches
(122 mm)
11.7 inches
(296 mm)
Accessories:
Model Description
793 301 DC Stop
275
Designed for co-siting purposes.
Enables feeder sharing.
Suitable for indoor or outdoor applications (IP 66).
With fault detection and integrated switch for multiple DC power
supply.
782 10469
Single unit
782 10469, 782 10808
Order Information:
Model Description
782 10469 Dualband combiner, single unit
782 10808 Dualband combiner, double unit
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit (optional) for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mounts to a at surface with four screws (max. 8 mm dia).
See Mechanical Accessories section for more information.
18501910/19301990 MHz
17101755/21102155 MHz
Dualband Combiner
11068-A
936.3232
Specications:
Pass band
PCS 18501910 (Rx) / 19301990 (Tx) MHz
AWS 17101755 (Rx) / 21102155 (Tx) MHz
Impedance 50 ohms
VSWR < 1.25:1 (18501910 / 19301990 MHz)
< 1.25:1 (17101755 / 21102155 MHz)
Insertion loss
Port PCSPort ANT <0.3 dB (18501910 / 19301990 MHz)
Port AWSPort ANT <0.2 dB (17101755 / 21102155 MHz)
Insolation
Port PCSPort AWS > 50 dB (18501910 / 19301990 MHz)
> 50 dB (17101755 / 21102155 MHz)
Input power
Port PCS < 250 watts (18501910 / 19301990 MHz)
Port AWS < 250 watts (17101755 / 21102155 MHz)
Intermodulation < -160 dBc (3rd order; with 2 x 20 W)
Power supply voltage
operational +10 +15 V DC (Port PCS)
+10 +30 V DC (Port AWS)
survival +10 +35 V DC
Polarity protection -48 V DC (Port PCS, Port AWS)
Maximum current 1.5 A (Port AWS)
Power supply current at PCS port
operating with dummy load 100 mA 20 mA (+10 +15 V DC)
Operating temperature -40 to +65 C
Connectors 7-16 DIN female (long neck)
Application Indoor or outdoor (IP 66)
Lightning protection 8/20 s, 20 kA; 10/350 s, 3 kA (Port ANT)
Weight single unit 5.5 lb (2.5 kg)
double unit 11 lb (5 kg)
Dimensions single unit 11.7 x 4.8 x 2.5 inches (296 x 122 x 64 mm)
double unit 11.7 x 4.8 x 4.7 inches (296 x 122 x 120 mm)
(includes mounting bracket)
276
782 10469, 782 10808 Dualband Combiner
The mounting plates can be removed and
replaced with other means of mounting by
removing the screws through (M5 x 10).
Caution: Exceeding the maximum drilled
depth of 8.5 mm with replacement
hardware and fasteners may permanently
damage the unit.
~
4 screws M5 x 10
4 spring washers 5.5 DIN 6095
~
4 screws M5 x 10
4 spring washers 5.5 DIN 6095
4.7 inches
(120 mm)
2.5 inches
(64 mm)
4.8 inches
(122 mm)
11.7 inches
(296 mm)
Port PCS Port ANT
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1.0
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
2110 2155
1850 1910
1930 1990
1710 1755
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
A
t
t
e
n
u
a
t
i
o
n
/
d
B
Frequency/MHz
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
2110 2155
1850 1910
1930 1990 1710 1755
Typical Attenuation Curves
Port AWS Port ANT
Diagram I
Diagram II
Port Port
PCS ANT
Port Port
AWS ANT
Port Port
AWS ANT
277
Designed for cable sharing/reduction in PCS and WiMAX
systems.
Can be used as a combiner near the BTS or in a reciprocal function
near the antenna.
Suitable for indoor or outdoor applications.
Wall or mast mounting.
Built-in lightning protection.
External DC stop available as an accessory.
Available as a single unit, or for XPol anten-nas as a double unit
Very low insertion loss.
Mounting Options:
Model Description
2 x 131 1847 Mounting Kit (optional) for 2 to 5.7 inch
(50 to 145 mm) OD mast.
Mounts to a at surface with four screws (max. 8 mm dia).
Mounts to 2 to 5.7 inch (50 to 145 mm) OD masts with optional mounting kit.
See Mechanical Accessories section for more information.
17102180 MHz
24002700 MHz
Dualband Combiner
11344-B
936.3367/b
782 10800, 782 11092, 782 11094
782 11091, 782 11093, 782 11095
General specications:
Pass band
Band 1 17102180 MHz
Band 2 24002700 MHz
Impedance 50 ohms
VSWR < 1.25:1 (17102180 / 24002700 MHz)
Insertion loss
Port 1Port 3 <0.15 dB
Port 2Port 3 <0.15 dB
Insolation
Port 1Port 2 > 60 dB
Input power, bands 1 & 2 < 300 watts
Intermodulation < -160 dBc (3rd order; with 2 x 20 W)
Operating temperature -40 to +60 C
Connectors 7-16 DIN female (long neck)
Application Indoor or outdoor (IP 66)
Lightning protection 3 kA 10/350 s pulse
Weight single unit 6.4 lb (2.9 kg)
double unit 12.6 lb (5.7 kg)
Dimensions single unit 12 x 7.8 x 2.5 inches (305 x 199 x 63 mm)
double unit 12 x 7.8 x 4.4 inches (305 x 199 x 113 mm)
Shipping dimensions
single unit 15.4 x 10.7 x 5.5 inches (392 x 272 x 139 mm)
double unit 15.4 x 10.7 x 7.4 inches (392 x 272 x 189 mm)
1710 2180 2400 2700
Specications: 782 10800 Single Unit 782 11092 Single Unit 782 11094 Single Unit
782 11091 Double Unit 782 11093 Double Unit 782 11095 Double Unitt
DC/AISG transparency
Port 1Port 3 By-pass (max. 2500mA) Stop By-pass (max. 2500mA)
Port 2Port 3 By-pass (max. 2500mA) By-pass (max. 2500mA) Stop
1710 2180 2400 2700 1710 2180 2400 2700
782 10800, 782 11092, 782 11094
Single Unit
782 11091, 782 11093, 782 11095
Double Unit
N
E
W
278
782 10800, 782 11092, 782 11094 Dualband Combiner
782 11091, 782 11093, 782 11095
2.4 inches
(62 mm)
12 inches
(305 mm)
4.4 inches
(113 mm)
7.8 inches
(199 mm)
Typical Attenuation Curves
Diagram I
port 1 jport 3 port 2 jport 3
Diagram II
port 1 jport 3 port 2 jport 3
279
Hybrid Combiner
782 10504
6982690 MHz
Built-in DC stop.
9 inches
(229 mm)
3.1 inches
(80 mm)
6.9 inches
(175 mm)
6.7 inches
(80 mm)
3.1 inches
(80 mm)
4.4 inches
(112 mm)
or
Specications: 782 10215 782 10216 782 10257 782 10265
Frequency range
Low band 824851 MHz 824851 MHz 824846.5 MHz 824846.5 MHz
High band 869896 MHz 869896 MHz 869891.5 MHz 869891.5 MHz
Impedance 50 ohms 50 ohms 50 ohms 50 ohms
VSWR <1.25:1 <1.25:1 <1.25:1 <1.25:1
Insertion loss
Antenna Low band <0.5 dB <0.5 dB <0.5 dB <0.5 dB
High bandAntenna <0.5 dB <0.5 dB <0.5 dB <0.5 dB
Isolation
Low bandHigh band >65 dB >65 dB >70 dB >70 dB
Maximum input power <400 watts (high band) <400 watts (high band) <400 watts (high band) <800 watts (high band)
max. 16 carriers max. 16 carriers max. 16 carriers max. 32 carriers
Intermodulation (2x20w) IM3: <-160 dBc IM3: <-160 dBc IM3: <-160 dBc IM3: <-160 dBc
Temperature range -20 to +55 C -20 to +55 C -20 to +55 C -20 to +55 C
Connectors 7-16 DIN female N female 7-16 DIN female 7-16 DIN female
Application Indoor Indoor Indoor Indoor
Dimensions* 9 x 6.7 x 3.1 inches 9 x 6.9 x 3.1 inches 9 x 6.7 x 3.1 inches 9 x 6.7 x 4.4 inches
(229 x 170 x 80 mm) (229 x 175 x 80 mm) (229 x 170 x 80 mm) (229 x 170 x 112 mm)
Weight 5.7 lb (2.6 kg) 5.7 lb (2.6 kg) 5.7 lb (2.6 kg) 6.6 lb (3 kg)
Shipping dimensions 12.2 x 9.9 x 6.4 inches 12.2 x 9.9 x 6.4 inches 12.2 x 9.9 x 6.4 inches 12.2 x 9.9 x 6.4 inches
(309 x 252 x 162 mm) (309 x 252 x 162 mm) (309 x 252 x 162 mm) (309 x 252 x 162 mm)
Mounting Mount using four screws Mount using four screws Mount using four screws Mount using four screws
(max. 4 mm diameter) (max. 4 mm diameter). (max. 4 mm diameter) (max. 4 mm diameter)
*Includes connectors and mounting feet
782 10215, 782 10216
10865-A
936.2384/b
782 10257, 782 10265
Mounting Options:
Description
See specications above.
Duplexer with Built-in DC Stop
286
TypicaI Attenuation Curves (782 10215, 782 10216)
Diagram I
0
10
20
30
40
50
60
70
80
90
100
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
810 820 830 840 850 860 870 880 890 900 910
824 - 851 869 - 896
Diagram II
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
810 820 830 840 850 860 870 880 890 900 910
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
869 - 896 824 - 851
High band Antenna Antenna Low band High band Antenna Antenna Low band
TypicaI Attenuation Curves (782 10257)
Diagram I
0
10
20
30
40
50
60
70
80
90
100
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
810 820 830 840 850 860 870 880 890 900 910
824 - 846.5 869 - 891.5
Diagram II
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
810 820 830 840 850 860 870 880 890 900 910
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
869 - 891.5 824 - 846.5
High band Antenna Antenna Low band High band Antenna Antenna Low band
TypicaI Attenuation Curves (782 10265)
Diagram I
0
10
20
30
40
50
60
70
80
90
100
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
810 820 830 840 850 860 870 880 890 900 910
824 - 846.5 869 - 891.5
Diagram II
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
810 820 830 840 850 860 870 880 890 900 910
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
869 - 891.5 824 - 846.5
High band Antenna Antenna Low band High band Antenna Antenna Low band
782 10215, 782 10216
782 10257, 782 10265
Duplexer with Built-in DC Stop
287
10849-B
936.2284/c
General specications: 782 10168, 782 10169, 782 10170 782 10171, 782 10172
Frequency range
Low band 824835 MHz 835851 MHz
High band 869880 MHz 880896 MHz
Impedance 50 ohms 50 ohms
VSWR <1.25:1 <1.25:1
Insertion loss
Antenna Low band <0.5 dB <0.5 dB
High bandAntenna <0.5 dB <0.5 dB
Isolation
Low bandHigh band >85 dB >85 dB
Maximum input power <400 watts (high band) <400 watts (high band)
max. 8 carriers max. 12 carriers
Intermodulation (2x20w) IM3: <-160 dBc IM3: <-160 dBc
Connectors 7-16 DIN female 7-16 DIN female
782 10168
782 10171
782 10169
782 10172
Indoor & Outdoor
Versions
Specications: 782 10170
Temperature range -20 to +55 C
Application Indoor
Dimensions 19 rack mount, 2 height units
6.7 inch (170 mm) plug-in depth
Weight 8.2 lb (3.7 kg)
Shipping dimensions 24.1 x 12.3 x 8.8 inches
(612 x 312 x 224 mm)
Mounting Mount using four screws
(max. 6 mm diameter)
782 10171, 782 10172
782 10168, 782 10169, 782 10170
Duplexer with Built-in DC Stop
Order Information:
Model Description
782 10168 Indoor duplexer
782 10169 Outdoor duplexer
782 10170 Indoor duplexer (19 rack mount)
782 10171 Indoor duplexer
782 10172 Outdoor duplexer
782 10170
(19 drawer)
The duplexer is designed to combine/split AMPS Tx and Rx
signals to/from one common Tx/Rx antenna in order to save
feeder cable and antenna costs
It can be used:
Built-in DC stop.
Built-in DC stop.
Specications:
Frequency range
Low band 18501910 MHz
High band 19301990 MHz
Impedance 50 ohms
VSWR <1.25:1
Insertion loss
Antenna Low band <0.7 dB
High bandAntenna <0.7 dB
Isolation
Low bandHigh band >65 dB
Maximum input power <150 watts (low or high band)
Intermodulation (2x20w) IM3: <-160 dBc
Temperature range -20 to +55 C
Connectors 7-16 DIN female
Application Indoor
Dimensions* 7.9 x 7.6 x 1.7 inches
(200 x 192 x 43 mm)
Weight 3.7 lb (1.7 kg)
*Includes connectors and mounting feet
1.7 inches
(43 mm)
Low Band
7.6 inches
(192 mm)
7.9 inches
(200 mm)
Antenna High Band
TypicaI Attenuation Curves
Diagram I
0
10
20
30
40
50
60
70
80
90
100
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020
1850 - 1910 1930 - 1990
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
1930 - 1990 1850 - 1910
Antenna Low band High band Antenna
Diagram II
Antenna Low band High band Antenna
792 544
Mounting Options:
Description
Mount using four screws (max. 4 mm diameter).
Duplexer with Built-in DC Stop
290
10857-A
936.958/a
Order Information:
Model Description
791 594 Band-stop lter 15501700 MHz
(indicate stop band frequency and bandwidth when ordering)
791 397 Band-stop lter 17001900 MHz
(indicate stop band frequency and bandwidth when ordering)
Specications:
Frequency range
791 594 15501700 MHz
791 397 17001900 MHz
Impedance 50 ohms
Maximum input power <15 watts (at inserion loss of <0.5 dB)
Connectors N female
Temperature range 0 to +50 C
Weight 1.8 lb (0.8 kg)
Dimensions 6.7 x 5.1 x 2.8 inches
including connectors (170 x 130 x 72 mm)
Shipping dimensions 8.3 x 6.3 x 3.5 inches
(210 x 160 x 90 mm)
The 791 594 and 791 397 Band-stop lters are used when
individual frequencies are to be attenuated. Due to their
easy tuning they are particularly suitable for laboratory test
purposes.
They can be used for:
As a combiner component.
Design and construction: The band-pass lter consists of two
capacitively coupled coaxial resonators mounted on a stable
mounting plate.
Filter characteristics: Narrow pass band with low insertion loss, high
stop band attenuation outside the pass band.
Tuning: The band pass lter is factory tuned to the indicated pass band
center frequency f
0
with a bandwidth of f
0
1.75 MHz. Tuning can also
be done by the customer by following the instructions provided.
For indoor use only.
Tuning examples: f
0
=1800 MHz f
0
=1900 MHz f
0
=2000 MHz
Insertion loss <1.2 dB <0.9 dB <0.8 dB
at f
0
f
0
1.75 MHz
Stop band attenuation
at f
0
10 MHz >16 dB >13 dB >9 dB
at f
0
15 MHz >24 dB >20 dB >15 dB
at f
0
120 MHz >29 dB >25 dB >20 dB
at f
0
125 MHz >33 dB >29 dB >24 dB
VSWR (input)
at f
0
f
0
1.75 MHz <1.6:1 <1.35:1 <1.3:1
0
5
10
15
20
25
30
35
40
45
50
-50 -40 -30 - 20 -10 f
0
+10 +20 +30 +40 +50
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
0
5
10
15
20
25
30
35
40
45
50
-50 -40 -30 -20 -10 f
0
+10 +20 +30 +40 +50
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
0
5
10
15
20
25
30
35
40
45
50
-50 -40 -30 -20 -10 f
0
+10 +20 +30 +40 +50
B
d
/
n
o
i
t
a
u
n
e
t
t
A
Frequency/MHz
f
0
= 1800 MHz f
0
= 2000 MHz f
0
= 1900 MHz
Typical Attenuation Curves
(Tuning examples)
Mounting Options:
Description
Mount using four screws (max. 4mm diameter)
Band-Pass Filter
293
10844-A
936.1320/a
Specications:
Frequency range 18002000 MHz
Impedance 50 ohms
Maximum input power <25 watts
Connector N female
Temperature range +10 to +40 C
Weight 2.2 lb (1 kg)
Dimensions 7.5 x 5.9 x 2.1 inches
including connectors (191 x 149 x 54 mm)
Shipping dimensions 7.9 x 5.9 x 3 inches
(200 x 150 x 75 mm)
The 792 219 Band-stop lter is used when individual frequencies
are to be attenuated. Due to its easy tuning it is particularly
suitable for laboratory test purposes.
It can be used for:
B
d
/
3
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
2
TypicaI attenuation between ports
12 resp. 13 vs. frequency
Diagram I
1.0 1.5 2.0
15
20
25
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
VSWR at port 1
(with 50-7 load at port 4)
Diagram II
TypicaI attenuation 2 3 vs. VSWR at port 1
K637061, K637067
Mounting Options:
Description
Mount using two screws (max. 5 mm diameter).
295 10861-A
936.2025/b
Specications:
Frequency range 806960 MHz
VSWR* <1.1:1
Impedance 50 ohms
Attenuation* 12 / 13 3 0.4 dB (see diagram I)
Attenuation* 23 See diagram II
Directivity >30 dB
Maximum input power <500 watts total power two inouts
with max. 350 watts at one input
Intermodulation (2x20w) IM3: -160 dBc
Connector 7-16 DIN female
Weight 4 lb (1.8 kg)
Dimensions 5.4 x 3.7 x 1.9 inches
including connectors (136 x 94 x 47 mm)
Shipping dimensions 6.3 x 3.7 x 2.6 inches
(160 x 95 x 65 mm)
*VSWR and attenuation values are measured when the remaining
ports are terminated with 50 ohm loads.
The 3-dB coupler can be used:
As a decoupled power spliter with a ratio of 1:1
For the decoupled combining of two transmitters with a
frequency spacing as narrow as desired (at 3 dB loss)
For the decouped combining of two receivers with frequency
spacing as narrow as desired
For the decoupled combining of two transmitter/receiver units,
whose integrated duplexers are within the same frequency
range
As a frequency-independent 90 phase shifter
As a component to form combiners
Function:
The 3-dB coupler has four ports, two of which are decoupled
from each other. For example, effective power entering into
port 1 is distributed into ports 2 and 3. Port 4 is decoupled and
without power if ports 2 and 3 are ideally matched. In practice
an absorber of suitable power at port 4 is to be planned in
accordance with the mismatch of ports 2 and 3.
Decoupled combining can be achieved via the diagonally
opposite ports 2 and 3 or 1 and 4.
For indoor or outdoor use (IP66).
1 3
2 4
1 3
1 2
2.5
3.0
3.5
Frequency/MHz
806 960
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
2
TypicaI attenuation between ports
12 resp. 13 vs. frequency
Diagram I
1.0 1.5 2.0
15
20
25
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
VSWR at port 1
(with 50-7 load at port 4)
Diagram II
TypicaI attenuation 2 3 vs. VSWR at port 1
793 506
3 dB Coupler
(90 Hybrid)
806960 MHz
Indoor or Outdoor Use
Mounting Options:
Description
Mount using two screws (max. 6 mm diameter).
806960 MHz 3 dB Coupler
296
Coupler
806960 MHz
Indoor Use Only
10845-A
936.1439/g
4.7, 6, 7, and 10 dB Couplers
Order Information:
Model Description
792 937 4.7 dB coupler with N female connector
792 170 4.7 dB coupler with 7-16 DIN female connector
793 105 6 dB coupler with N female connector
792 180 6 dB coupler with 7-16 DIN female connector
793 106 7 dB coupler with N female connector
793 107 7 dB coupler with 7-16 DIN female connector
793 108 10 dB coupler with N female connector
790 213 10 dB coupler with 7-16 DIN female connector
Specications:
Frequency range 806960 MHz
Directivity >27 dB
VSWR* <1.1:1
Impedance 50 ohms
Maximum input power <350 watts total power
Connector N or 7-16 DIN female
Weight 1.3 lb (0.6 kg)
Dimensions 6.2 x 3.7 x 2.2 inches (max.)
including connectors (157 x 95 x 55 mm)
Shipping dimensions 11.8 x 4.5 x 2.6 inches
(300 x 115 x 65 mm)
The 4.7-dB coupler is used as a decoupled splitter for power splitting
purposes at a 1:2 ratio.
For example an effective power entering into port 1 is divided between
the ports 2 and 3 at a ratio of 1:2.
Thus 1/3 of the input power (attenuation: 4.7 dB) is available at port 2 and
2/3 of the input power is available at port 3.
The 6-dB coupler is used as a decoupled splitter for power splitting
purposes at a 1:3 ratio.
For example an effective power entering into port 1 is divided between
the ports 2 and 3 at a ratio of 1:3.
Thus 1/4 of the input power (attenuation: 6 dB) is available at port 2 and
3/4 of the input power is available at port 3.
The 7-dB coupler is used as a decoupled splitter for power splitting
purposes at a 1:4 ratio.
For example an effective power entering into port 1 is divided between
the ports 2 and 3 at a ratio of 1:4.
Thus 1/5 of the input power (attenuation: 7 dB) is available at port 2 and
4/5 of the input power is available at port 3.
The 10-dB coupler is used as a decoupled splitter for power splitting
purposes at a 1:9 ratio.
For example an effective power entering at port 1 is divided between the
ports 2 and 3 at a ratio of 1:9.
Thus 1/10 of the input power (attenuation: 10 dB) is available at port 2 and
9/10 of the input power is available at port 3.
Port 4 is decoupled and remains free of power if the ports 2 and 3 are
ideally matched. In practice an absorber of suitable power at port 4 is to
be planned in accordance with the mismatch of ports 2 and 3.
Decoupled combining can be achieved via the diagonally opposite ports 2
and 3 respectively 1 and 4.
4.7 dB Coupler 6 dB Coupler 7 dB Coupler 10 dB Coupler
Attenuation* 13 (42) 1.8 0.3 dB 1.25 0.2 dB 1.0 0.2 dB 0.5 0.2 dB
Attenuation* 12 (43) 4.7 0.5 dB 6 0.5 dB 7 0.5 dB 10 0.5 dB
*VSWR and attenuation values are measured when the remaining ports are terminated with 50 ohm loads.
1 3
2 4
Mounting Options:
Description
Mounts using two screws (max. 5.5 mm diameter).
806960 MHz Couplers
297
6 and 10 dB Couplers
10859-A
936.1600/e
Order Information:
Model Description
792 964 6 dB coupler with N female connector
792 965 6 dB coupler with 7-16 DIN female connector
792 966 10 dB coupler with N female connector
792 967 10 dB coupler with 7-16 DIN female connector
Specications:
Frequency range 8001900 MHz
VSWR* <1.15:1
Impedance 50 ohms
Maximum input power <350 watts total power two inouts
with max. 250 watts at one input
Connector N or 7-16 DIN female
Weight 1.1 lb (0.5 kg)
Dimensions 5.3 x 3.7 x 1.6 inches (max.)
including connectors (135 x 95 x 40 mm)
Shipping dimensions 10.8 x 4.5 x 1.9 inches
(275 x 115 x 47 mm)
The 6-dB coupler is used as a decoupled splitter for power
splitting purposes at a 1:3 ratio.
For example an effective power entering into port 1 is divided
between the ports 2 and 3 at a ratio of 1:3.
Thus 1/4 of the input power (attenuation: 6 dB) is available at
port 2 and 3/4 of the input power is available at port 3.
The 10-dB coupler is used as a decoupled splitter for power
splitting purposes at a 1:9 ratio.
For example an effective power entering at port 1 is divided
between the ports 2 and 3 at a ratio of 1:9.
Thus 1/10 of the input power (attenuation: 10 dB) is available
at port 2 and 9/10 of the input power is available at port 3.
Port 4 is decoupled and remains free of power if the ports 2 and
3 are ideally matched. In practice an absorber of suitable power
at port 4 is to be planned in accordance with the mismatch of
ports 2 and 3.
Decoupled combining can be achieved via the diagonally opposite
ports 2 and 3 respectively 1 and 4.
For indoor use only.
6 dB Coupler 10 dB Coupler
Attenuation* 13 (42) 1.5 0.5 dB (8001900 MHz) 0.5 0.5 dB (8001900 MHz)
Attenuation* 12 (43) 6 1 dB (800960 / 17001900 MHz) 10 1 dB (800960 / 17001900
MHz)
6 1.5 dB (9601700 MHz) 10 2 dB (9601700 MHz)
1 3
2 4
Mounting Options:
Description
Mount using two screws (max. 5.5 mm diameter).
8001900 MHz Couplers
3 dB Coupler
8001900 MHz
Indoor Use Only
298
3 dB Coupler
(90 Hybrid)
8002200 MHz
Indoor or Outdoor Use
10862-A
936.2235/c
Specications:
Frequency range 8002200 MHz
VSWR* <1.2:1
Impedance 50 ohms
Attenuation* 12 / 13 3 1.2 dB (see diagram I)
Attenuation* 23 See diagram II
Directivity >20 dB
Maximum input power <300 watts total power two inouts
with max. 200 watts at one input
Intermodulation (2x20w) IM3: -160 dBc
Temperature range -30 to +70 C
Connector 7-16 DIN female
Weight 2.9 lb (1.3 kg)
Dimensions 4.1 x 3.7 x 2.1 inches
including connectors (105 x 94 x 53 mm)
Shipping dimensions 6.3 x 3.7 x 2.6 inches
(160 x 95 x 65 mm)
*VSWR and attenuation values are measured when the remaining
ports are terminated with 50 ohm loads.
The 3-dB coupler can be used:
As a decoupled power spliter with a ratio of 1:1
For the decoupled combining of two transmitters with a
frequency spacing as narrow as desired (at 3 dB loss)
For the decouped combining of two receivers with frequency
spacing as narrow as desired
For the decoupled combining of two transmitter/receiver units,
whose integrated duplexers are within the same frequency
range
As a frequency-independent 90 phase shifter
As a component to form combiners
Function:
The 3-dB coupler has four ports, two of which are decoupled
from each other. For example, effective power entering into
port 1 is distributed into ports 2 and 3. Port 4 is decoupled and
without power if ports 2 and 3 are ideally matched. In practice
an absorber of suitable power at port 4 is to be planned in
accordance with the mismatch of ports 2 and 3.
Decoupled combining can be achieved via the diagonally
opposite ports 2 and 3 or 1 and 4.
For indoor or outdoor use (IP66).
1 3
2 4
1 2
1 3
2.0
3.0
4.0
800 2200
TypicaI attenuation between ports
12 resp. 13 vs. frequency
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
2
Diagram I
1.0 1.5 2.0
15
20
25
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
VSWR at port 1
(with 50-7 load at port 4)
Diagram II
TypicaI attenuation 2 3 vs. VSWR at port 1
793 554
Mounting Options:
Description
Mount using two screws (max. 5.5 mm diameter).
8002200 MHz Coupler
299
10860-A
936.2072/b
Specications:
Frequency range 17002200 MHz
VSWR* <1.15:1
Impedance 50 ohms
Attenuation* 12 / 13 3 0.4 dB (see diagram I)
Attenuation* 23 See diagram II
Directivity >25 dB
Maximum input power <300 watts total power two inouts
with max. 200 watts at one input
Intermodulation (2x20w) IM3: -160 dBc
Connector 7-16 DIN female
Weight 2.9 lb (1.3 kg)
Dimensions 3.7 x 3.5 x 2.4 inches
including connectors (94 x 88 x 60 mm)
Shipping dimensions 6.3 x 3.7 x 2.6 inches
(160 x 95 x 65 mm)
*VSWR and attenuation values are measured when the remaining
ports are terminated with 50 ohm loads.
The 3-dB coupler can be used:
As a decoupled power spliter with a ratio of 1:1
For the decoupled combining of two transmitters with a
frequency spacing as narrow as desired (at 3 dB loss)
For the decoupled combining of two receivers with frequency
spacing as narrow as desired
For the decoupled combining of two transmitter/receiver units,
whose integrated duplexers are within the same frequency
range
As a frequency-independent 90 phase shifter
As a component to form combiners
Function:
The 3-dB coupler has four ports, two of which are decoupled
from each other. For example, effective power entering into
port 1 is distributed into ports 2 and 3. Port 4 is decoupled and
without power if ports 2 and 3 are ideally matched. In practice
an absorber of suitable power at port 4 is to be planned in
accordance with the mismatch of ports 2 and 3.
Decoupled combining can be achieved via the diagonally
opposite ports 2 and 3 or 1 and 4.
For indoor or outdoor use (IP66).
1 3
2 4
1 3
1 2
2.5
3.0
3.5
Frequency/MHz
1700 2200
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
2
TypicaI attenuation between ports
12 resp. 13 vs. frequency
Diagram I
1.0 1.5 2.0
15
20
25
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
VSWR at port 1
(with 50-7 load at port 4)
Diagram II
TypicaI attenuation 2 3 vs. VSWR at port 1
Mounting Options:
Description
Mount using two screws (max. 5.5 mm diameter).
3 dB Coupler
17002200 MHz
Indoor or Outdoor Use
793 006 17002200 MHz Coupler
300
10863-B
936.2425/d
Specications:
Frequency range 8002200 MHz
Attenuation*
Tx1Antenna 3 1.2 dB
Tx2Antenna 3 1.2 dB
Tx1Tx2 See diagram
Impedance 50 ohms
VSWR* <1.2:1
Intermodulation (2x20w) IM3: -160 dBc
Maximum input power <150 watts
per Tx port with max. 16 signals
at each port
Connectors 7-16 DIN female
Temperature range -20 to +50 C
Weight 21.6 lb (9.8 kg)
Dimensions 17.5 x 13.2 x 2.5 inches
(444 x 336 x 64 mm)
Shipping dimensions 20.1 x 16.1 x 3.9 inches
(510 x 410 x 100 mm)
* VSWR and attenuation values are measured when the remaining
ports are terminated with 50 ohm loads
The 793 555 3 dB Coupler with Cable Absorber is designed
to combine two BTS (Base Tranceiver Stations) onto one
antenna to save feeder cable and antenna costs.
B
d
/
4
1
n
o
i
t
a
u
t
n
e
t
t
A
B
d
/
2
1 4
1 2
2.5
3.0
3.5
Frequency/MHz
890 960
TypicaI attentuation 1 2 and 1 4
vs. frequency
1
n
o
i
t
a
u
t
n
e
t
t
A
B
d
/
4
1
n
o
i
t
a
u
t
n
e
t
t
A
B
d
/
2
1 2
1 4
2.5
3.0
3.5
Frequency/MHz
1710 1880
TypicaI attenuation 1 2 and 1 4
vs. frequency
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
4
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
2
20
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
4
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
30
40
Attenuation 1 3 or 2 4 vs. frequency
Frequency/MHz
960 940 900 860 820
typical attenuation
guaranteed attenuation
806
20
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
4
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3
30
40
Attenuation 1 3 or 2 4 vs. frequency
Frequency/MHz
1900 1850 1800 1750 1700
typical attenuation
guaranteed attenuation
20
2
n
o
i
t
a
u
n
e
t
t
A
B
d
/
4
1
n
o
i
t
a
u
n
e
t
t
A
B
d
/
3 30
40
Attenuation 1 3 or 2 4 vs. frequency
Frequency/MHz
960 950 930 910 890
typical attenuation
guaranteed attenuation
Diagram II Diagram I
Diagram II
Diagram II
Diagram I
Diagram I
K6373621
790 881
790-498
Typical Attenuation Curves
K6373621, 790 881, 791 498 Hybrid Ring Junction
305
10471-C
936.131/i
50 Ohm RF Loads
Kathrein RF loads are manufactured to the most exacting
standards and are highlighted by the following features:
1.5 watt model IP rated IP65 for outdoor use, all other models
for indoor use only
K6226111
T50MN/2
50 OHM RF LOADS RF Loads
K6226301
T50FN/50
K6226501
T50FN/100
K6226201
T50FN/25
K6226401
T50FN/10
784 10367
T50M7/1.5
Specications:
Power Frequency
Rating* Range VSWR Connector Dimensions Weight Model
0.5 watt 02700 MHz <1.08:1 (01000 MHz) N male 1.3 in. long, 0.8 in. diameter 0.09 lb K6226611
<1.15:1 (10002000 MHz) 33 mm long, 21 mm diameter 0.04 kg T50MN/0.5
<1.2:1 (20002700 MHz)
1.5 watt 04000 MHz <1.1:1 (02000 MHz) 7-16 male 1.6 in. long, 1.3 in. diameter 0.27 lb 784 10367
<1.3:1 (20004000 MHz) 40 mm long, 32 mm diameter 0.12 kg T50M7/1.5
7-16 female 1.6 in. long, 1.1 in. diameter 0.27 lb 784 10470
40 mm long, 29 mm diameter 0.12 kg
2 watt 02700 MHz <1.08:1 (01000 MHz) N male 1.3 in. long, 0.8 in. diameter 0.09 lb K6226111
<1.15:1 (10002000 MHz) 33 mm long, 21 mm diameter 0.04 kg T50MN/2
<1.2:1 (20002700 MHz)
10 watt 02700 MHz <1.08:1 (01000 MHz) N male 3.3 x 3.2 x 1.6 inches** 0.55 lb K6226411
<1.15:1 (10002000 MHz) 85 x 82 x 40 mm** 0.25 kg T50MN/10
<1.2:1 (20002700 MHz)
N female 3.2 x 3 x 1.6 inches** 0.55 lb K6226401
82 x 77 x 40 mm** 0.25 kg T50FN/10
25 watt 02700 MHz <1.08:1 (01000 MHz) N male 4.8 x 3.7 x 1.4 inches** 1.1 lb K6226211
<1.15:1 (10002000 MHz) 121 x 94 x 35 mm** 0.5 kg T50MN/25
<1.2:1 (20002700 MHz)
N female 4.4 x 3.7 x 1.4 inches** 1.1 lb K6226201
113 x 94 x 35 mm** 0.5 kg T50FN/25
7-16 male 4.9 x 1.4 x 3.7 inches** 1.1 lb K6226217
124 x 94 x 35 mm** 0.5 kg T50M7/25
7-16 female 4.9 x 3.7 x 1.4 inches** 1.1 lb K6226207
125 x 94 x 35 mm** 0.5 kg T50F7/25
50 watt 02700 MHz <1.08:1 (01000 MHz) N male 5.4 x 3.5 x 2.6 inches** 1.8 lb K6226311
<1.15:1 (10002000 MHz) 138 x 90 x 67 mm** 0.8 kg T50MN/50
<1.2:1 (20002700 MHz)
N female 5.1 x 3.5 x 2.6 inches** 1.8 lb K6226301
130 x 90 x 67 mm** 0.8 kg T50FN/50
7-16 male 5.2 x 3.5 x 2.6 inches** 1.8 lb K6226317
133 x 90 x 67 mm** 0.8 kg T50M7/50
7-16 female 5.3 x 3.5 x 2.6 inches** 1.8 lb K6226307
134 x 90 x 67 mm** 0.8 kg T50F7/50
100 watt 01000 MHz <1.08:1 N male 6.3 x 6.1 x 4.5 inches** 5.3 lb K6226511
161 x 156 x 114 mm** 2.4 kg T50MN/100
N female 6.1 x 6 x 4.5 inches** 5.3 lb K6226501
156 x 153 x 114 mm** 2.4 kg T50FN/100
7-16 female 6.7 x 6.1 x 4.5 inches** 5.3 lb K6226507
170 x 156 x 114 mm** 2.4 kg T50F7/100
* Power rating at 40C ambient temperature. ** Includes connector length
The maximum power rating increases or decreases
with falling or rising ambient temperature.
306
Mechanical Accessories
Mounting Congurations
806 - 960 MHz Panels ................................................................................................................................................................309
1425 - 2700 MHz Panels .......................................................................................................................................................310
Mounting Kit Options for Panel Antennas
1 x 738 546 ..........................................................................................................................................................................................................311
2 x 738 546 ..........................................................................................................................................................................................................311
3 x 738 546 ..........................................................................................................................................................................................................311
1 x 131 1847 .....................................................................................................................................................................................................311
2 x 131 1847 .....................................................................................................................................................................................................311
850 10002 ...............................................................................................................................................................................................................311
850 10003 ...............................................................................................................................................................................................................311
Tilt Kit Options for Panel Antennas
840 90013 ...............................................................................................................................................................................................................312
850 10007 ...............................................................................................................................................................................................................312
850 10013 ...............................................................................................................................................................................................................312
3-Sector Panel Mounting Brackets
742 033 .........................................................................................................................................................................................................................314
742 034 .........................................................................................................................................................................................................................314
742 263 .........................................................................................................................................................................................................................315
Dimensions of Panel Proles .......................................................................................................................................................316
3-Sector DTMA Mounting Brackets
782 10347, 782 10348, 782 10349 ................................................................................................................319
Dual Panel Mounting Kit
742 113 .........................................................................................................................................................................................................................320
850 10006 ...............................................................................................................................................................................................................321
2 x 850 10002 ................................................................................................................................................................................................321
2 x 850 10003 ................................................................................................................................................................................................321
Mounting Kit Options for Omni & Directional Antennas
Mounting Matrix .........................................................................................................................................................................................322
MKPP-23 ...................................................................................................................................................................................................................323
MKPS-1 ........................................................................................................................................................................................................................323
MKPS-2 ........................................................................................................................................................................................................................323
MKPS-3 ........................................................................................................................................................................................................................323
MKPS-4 ........................................................................................................................................................................................................................323
MKPS-5 ........................................................................................................................................................................................................................323
MKPS-13 ...................................................................................................................................................................................................................323
MKPX-2 ........................................................................................................................................................................................................................323
MKPX-3 ........................................................................................................................................................................................................................324
MKPX-4 ........................................................................................................................................................................................................................324
MKPX-5 ........................................................................................................................................................................................................................324
MKPX-6 ........................................................................................................................................................................................................................324
MKPX-9 ........................................................................................................................................................................................................................323
MKPX-10 ...................................................................................................................................................................................................................324
MKPX-11 ...................................................................................................................................................................................................................324
MKPX-12 ...................................................................................................................................................................................................................324
Tilt Kit Options for Omni & Directional Antennas
MKTB-1 .......................................................................................................................................................................................................................324
MKTB-3 .......................................................................................................................................................................................................................324
Azimuth Adjustment Kit for Panel Antennas
850 10014 ..............................................................................................................................................................................................................325
850 10015 ..............................................................................................................................................................................................................325
850 10016 ..............................................................................................................................................................................................................325
850 10017 ..............................................................................................................................................................................................................325
307
M
e
c
h
a
n
i
c
a
l
A
c
c
e
s
s
o
r
i
e
s
S
electing the right mounting hardware is painless with the
broad selection of clamps, bands, tilt kits, and specialty items
needed to securely and correctly install Kathrein antennas.
308
309
Mounting Congurations for Panel Antennas 806960 MHz
Mechanical Tilt Standard Mount
Mounting for 2 to 4.6 inch
(50 to 115 mm) OD mast
Sector Mount
Mounting for 2.375 to 6 inch
(60 to 152 mm) OD mast
Using 1 x 738 546, 2 x 738 546, 3 x 738 546
mounting kits.
Using 742 033, 742 263, 742 034 mounting kits.
Using 850 10013 and 737 976 tilt mount kits.
310
Mounting Congurations for Panel Antennas
14252700 MHz
Standard Panel Large Panel
(optional mounting
for any PCS panel)
Standard Tilt
Using 2 x 131 1847 mounting kit. Using 2 x 738 546 mounting kit.
Using 850 10013 tilt mount kit.
311
Mounting Kit Options for Panel Antennas
1 x 738 546
2 x 738 546
3 x 738 546
850 10002
850 10003
1 x 131 1847
2 x 131 1847
2 x 738 546*
3 x 738 546*
for use with most 3-point mount panel antennas
ships in sets of 3 brackets
Mast dia. 24.5 inches (50115 mm)
Weight 6 lb (2.7 kg)
for use with 2-point mount panel antennas
> 48 inches (1219 mm) long
ships in sets of 2 brackets
Mast dia. 24.5 inches (50115 mm)
Weight 4 lb (1.8 kg)
1 x 738 546*
for use with most 1-point mount Cellular
panel antennas
Mast dia. 24.5 inches (50115 mm)
Weight 2 lb (0.9 kg)
2 x 131 1847
for use with 2-point mount PCS panel antennas
<48 inches (1219 mm) long
and accessories
Mast dia. 25.7 inches (50145 mm)
1 x 131 1847
for use with 1-point mount PCS panel antennas
<48 inches (1219 mm) long
and accessories
Mast dia. 25.7 inches (50145 mm)
Mounting Kits
* 850 10002 Mounting clamp for 4.38.7 inch
(110220 mm) OD steel mast
11.9 lb (5.4 kg).
* 850 10003 Mounting clamp for 8.315 inch
(210380 mm) OD steel mast.
21.2 lb (9.6 kg).
312 10884-A
850 10013
for use with 2-point mount panel antennas
> 48 inches (1219 mm) long
Note: 3-point point panel antennas require an
additional 840 90013 bracket
64 mm
M8
64 mm
M8
850 10007
for use with 2-point mount
Cellular and Dualband panel antennas
from 55110 lb (2550 kg)
Tilt Kit Options for Panel Antennas
850 10013
840 90013
850 10007
Tilt Mount Kits
313
Model Description
850 10013 Locking Tilt Mount Kit for use with 2-point mount
50.951 inch (12941296 mm) panel antennas, 015 degrees downtilt angle
7676.3 inch (19301936 mm) panel antennas, 011 degrees downtilt angle
101.6 inch (2580 mm) panel antennas, 08 degrees downtilt angle
Weight 7.4 lb (3.7 kg)
Material Hot-dip galvanized steel
Fasteners Stainless steel
840 90013 Locking Tilt Mount Bracket for use with 850 10013 to change from 2-point to 3-point mount
Weight 5.1 lb (2.3 kg)
Material Hot-dip galvanized steel
Fasteners Stainless steel
850 10007 Heavy-duty Tilt Mount Kit for use with 2-point mount panel antennas 55110 lb (2550 kg)
downtilt angle dependent on antenna length.
Weight 13 lb (5.9 kg)
Material Hot-dip galvanized steel
Fasteners Stainless steel
Tilt Kit Options for Panel Antennas
314
3 Sector Panel Mounting Brackets
742 033, 742 034
Dimensions:
742 033 A B C D E F Dout
inches 4.5 3.5 8.5 8.2 1.9 1.8 18.1
mm 114.3 88 217 207 49 45 460
742 034 A B C D E F Dout
inches 5.5 3.9 9.3 9 1.9 1.8 19
mm 139.7 100 236 228 49 45 482
Specications:
Angle between antennas 120
Suitable for mast diameter*
742 033 4.5 inches (114.3 mm) OD.
742 034 5.5 inches (139.7 mm) OD.
Number of pieces 2 x 3 sector clamp
2 x mounting support clamp
Materials
3 sector clamp Hot-dip galvanized steel
Mounting support clamp Aluminum
Fasteners Stainless steel
Outer diameter (Dout) of the 3 A-Panel Arrangement
742 033 18.1 inches (460 mm)
742 034 19 inches (482 mm)
* Customer assumes all responsibility to ensure that the mounting pipe is
adequate to support the intended load. For use with steel pipe only (not
aluminum) with a minimum 0.25 inch (6 mm) wall thickness.
Dout
A
Torque: 5.9 ft-lb (8 Nm)
B
C
D
60
Mounting support clamp
E
F
3 sector clamp
(supports the antenna assembly
during azimuth adjustment)
Slim and unobtrusive design.
Nearly cylindrical optical appearance with a small outer diameter.
All components can be ordered separately (antennas or clamps).
Mounting support clamp that holds the antenna assembly in vertical position for safe
and easy azimuth adjustment.
Suitable for all A-Panels with a width of 1010.4 inches (254262 mm).
Order Information:
Model Description
742 033 Three-panel Sector Mounting Kit
(120 deg. ea.) for 4.5 inch
(114.3 mm) OD steel mast.
742 034 Three-panel Sector Mounting Kit
(120 deg. ea.) for 5.5 inch
(139.7 mm) OD steel mast.
315
3 Sector Panel Mounting Bracket 742 263
Specications:
Angle between antennas 120
Suitable for mast diameter* 3.5 inches (88.9 mm) OD. For use with steel
pipe only (not aluminum) with a minimum 0.25
inch (6 mm) wall thickness.
Number of pieces 2 x 3 sector clamp
2 x mounting support clamp
Materials
3 sector clamp Hot-dip galvanized steel
Mounting support clamp Aluminum
Fasteners Stainless steel
Outer diameter (Dx) of the
3 F-Panel Arrangement 10.2 inches (260 mm) minimum
3 F-Panel Arrangement 12.4 inches (315 mm) maximum
* Customer assumes all responsibility to ensure that the mounting pipe is ad-
equate to support the intended load.
Dimensions: A B C D E F D1 D2
inches 3.5 2.6 7.1 6.6 2 1.7 12.4 10.2
mm 88.9 65 180 168 50 42 315 260
D1
D2
D2
D1
A
Torque:
5.9 ft-lb
(8 Nm)
B
C
D
60
Mounting support clamp
E
3 sector clamp
(supports the antenna assembly
during azimuth adjustment)
Slim and unobtrusive design.
Nearly cylindrical optical appearance with a small outer diameter.
All components can be ordered separately (antennas or clamps).
Mounting support clamp that holds the antenna assembly in vertical position for safe
and easy azimuth adjustment.
Suitable for all F-Panels with a width of 6.1 inches (155 mm).
F
316
Dimensions of Panel Proles
5.39 inches
(137 mm)
10.63 inches
(270 mm)
PA1
6.34 inches
(161 mm)
10.63 inches
(270 mm)
PA2
10.63 inches
(270 mm)
6.73 inches
(171 mm)
PA3
5.04 inches
(128 mm)
10.51 inches
(267 mm)
PC1
4.33 inches
(110 mm)
10.2 inches
(259 mm)
PC2
Note: The dimensions listed here show the
maximum outside dimensions including
mounting brackets, end caps, etc. and
therefore may not match dimensions
shown on individual data sheets.
12.13 inches
(308 mm)
6.93 inches
(176 mm)
PA4
10.59 inches
(269 mm)
6.65 inches
(169 mm)
PA5
4.49 inches
(114 mm)
11.93 inches
(303 mm)
PC3
4.49 inches
(114 mm)
10.2 inches
(259 mm)
PC4
10926-E
317
6.42 inches
(163 mm)
1.97 inches
(50 mm)
PF1
2.52 inches
(64 mm)
6.42 inches
(163 mm)
PF2
3.11 inches
(79 mm)
10.63 inches
(270 mm)
PF3
2.52 inches
(64 mm)
6.42 inches
(163 mm)
PF4
3.27 inches
(83 mm)
6.38 inches
(162 mm)
PF5
8.11 inches
(206 mm)
3.47 inches
(88 mm) PF6
3.54 inches
(90 mm)
12.05 inches
(306 mm)
PF7
3.82 inches
(97 mm)
12.99 inches
(330 mm)
PF8
3.82 inches
(97 mm)
6.1 inches
(155 mm)
PF9
Dimensions of Panel Proles
3.43 inches
(87 mm)
6.1 inches
(155 mm)
PF10
4.25 inches
(108 mm)
6.1 inches
(155 mm)
PF11
318
Dimensions of Panel Proles
742 033 and 742 034
Dout
5
4
+
5
4
5
4
+
5
4
+ 4 5 4 5
742 263
Dout
Note: The dimensions listed here show the maximum outside dimensions including mounting brackets, end caps, etc.
and therefore may not match dimensions shown on individual data sheets.
Dout Dout Dout
742 263 742 033 742 034
Prole Width Depth Mast dia. 3.5" (88.9 mm) 4.5" (114.3 mm) 5.5" (139.7 mm)
PA1 10.63 inches 5.39 inches Not 18.1 inches 19 inches
(270 mm) (137 mm) Recommended (460 mm) (483 mm)
PA2 10.63 inches 6.34 inches Not 20 inches 21 inches
(270 mm) (161 mm) Recommended (508 mm) (533 mm)
PA3 10.63 inches 6.73 inches Not 21 inches 21.9 inches
(270 mm) (171 mm) Recommended (533 mm) (556 mm)
PA4 12.13 inches 6.93 inches Not 22 inches 23 inches
(308 mm) (176 mm) Recommended (559 mm) (584 mm)
PA5 10.59 inches 6.65 inches Not 21 inches 22 inches
(269 mm) (169 mm) Recommended (533 mm) (559 mm)
PC1 10.51 inches 5.04 inches Not 18.5 inches 19.4 inches
(267 mm) (121 mm) Recommended (470 mm) (493 mm)
PC2 10.2 inches 4.33 inches Not 17.7 inches 18.3 inches
(259 mm) (110 mm) Recommended (450 mm) (465 mm)
PC3 11.93 inches 4.49 inches Not 19 inches 19.8 inches
(303 mm) (114 mm) Recommended (483 mm) (502 mm)
PC4 10.4 inches 4.49 inches Not 18.5 inches 19 inches
(255 mm) (114 mm) Recommended (470 mm) (483 mm)
PF1 6.42 inches 1.97 inches 10.2 inches 12 inches 13 inches
(163 mm) (50 mm) (259 mm) (305 mm) (330 mm)
PF2 6.42 inches 2.52 inches 10.2 inches 12.25 inches 13.25 inches
(163 mm) (64 mm) (259 mm) (311 mm) (337 mm)
PF3 10.63 inches 3.11 inches 13.7 inches 15.5 inches 16 inches
(270 mm) (79 mm) (348 mm) (394 mm) (406 mm)
PF4 6.42 inches 2.52 inches 12 inches 13.75 inches 14.5 inches
(163 mm) (64 mm) (305 mm) (349 mm) (368 mm)
PF5 6.38 inches 3.27 inches 12.5 inches 14.5 inches 15.5 inches
(162 mm) (83 mm) (318 mm) (368 mm) (394 mm)
PF6 8.11 inches 3.47 inches 13.7 inches 15.5 inches 16.3 inches
(206 mm) (88 mm) (348 mm) (393 mm) (414 mm)
PF7 12.05 inches 3.54 inches NA 17.1 inches 18 inches
(306 mm) (90 mm) (434 mm) (457 mm)
PF8 12.99 inches 3.82 inches NA 17.7 inches 18.4 inches
(330 mm) (97 mm) (450 mm) (467 mm)
PF9 6.1 inches 3.82 inches 14.2 inches 15.7 inches 16.7 inches
(155 mm) (97 mm) (360 mm) (399 mm) (424 mm)
PF10 6.1 inches 3.43 inches 12.75 inches 14.8 inches 15.7 inches
(155 mm) (87 mm) (324 mm) (375 mm) (400 mm)
PF11 6.1 inches 4.25 inches 14.5 inches 16.3 inches 17.3 inches
(155 mm) (108 mm) (368 mm) (413 mm) (439 mm)
For antennas with rear facing connectors contact Kathrein Scala Division Sales Engineering to verify
compatibility with sector mount brackets.
319
Bottom view
Lower Clamp
Upper Clamp
3 Sector DTMA Mounting Brackets
782 10347, 782 10348, 782 10349
Dimensions:
782 10347 A B C D Dout
inches 3.5 2.8 6.7 7.7 14.2
mm 88.9 70 170 196 360
782 10348 A B C D Dout
inches 4.5 3.3 7.5 8.6 15.4
mm 114.3 83 190 219 390
782 10349 A B C D Dout
inches 5.5 3.7 8.7 8.9 16.3
mm 139.7 95 221 225 415
Specications:
Angle between DTMAs 120
Suitable for mast diameter*
782 10347 3.5 inches (88.9 mm) OD.
782 10348 4.5 inches (114.3 mm) OD.
782 10349 5.5 inches (139.7 mm) OD.
Number of pieces 2 x 3 sector clamp
Materials
3 sector clamp Stainless steel
Fasteners Stainless steel
Outer diameter (Dout) of the 3 DTMA Arrangement
782 10347 14.2 inches (360 mm)
782 10348 15.4 inches (390 mm)
782 10349 16.3 inches (415 mm)
Weight (includes both upper and lower clamp)
782 10347 4.2 lbs (1.9 kg)
782 10348 4.4 lbs (2 kg)
782 10349 5.3 lbs (2.4 kg)
Dout
A
Torque: 12.514.8 ft-lb
(1720 Nm)
60
Slim and unobtrusive design.
Nearly cylindrical optical appearance with a small outer diameter.
Order Information:
Model Description
782 10347 Three DTMA Sector Mounting Kit
(120 deg. ea.) for 3.5 inch
(88.9 mm) OD steel mast.
782 10348 Three DTMA Sector Mounting Kit
(120 deg. ea.) for 4.5 inch
(139.7 mm) OD steel mast.
782 10349 Three DTMA Sector Mounting Kit
(120 deg. ea.) for 5.5 inch
(139.7 mm) OD steel mast.
Torque: 8.911.1 ft-lb
(1215 Nm)
D
C
B
320
Conguration
without mechanical downtilt
Conguration
with mechanical downtilt
Dual Panel Mounting Kit 742 113
The 742 113 Dual Panel Mounting Kit consists of two hot-dip
galvanized mounting plates and necessary fasteners. It is used to
mount two 65 or 90 panel antennas side by side.
Specications:
Number of mounting plates 2
Antenna length 79 inches (2000 mm) maximum
width 6.1 inches (155 mm) maximum
Material hot-dip galvanized steel
Weight 3.5 lb (1.6 kg)
Dimensions 10.6 x 6.1 x 0.4 inches (270 x 116 x 10 mm)
Mounting Mounts using the supplied fasteners
6.1 inches
(116 mm)
10.6 inches
(270 mm)
Order Information:
Model Description
742 113 Dual Panel Mounting Kit
321 11201-A
936.2432/a
Dual Panel Mounting Kit
The 850 10006 Dual Panel Mounting Kit consists of two hot-dip
galvanized mounting plates and necessary fasteners. It is used to mount
panels with a maximum width of 10.3 inches (262 mm) and less than 55
lb (25 kg) each.
Specications:
Number of mounting plates 2
Antenna length 102.4 inches (2600 mm) maximum
width 10.3 inches (262 mm) maximum
Material clamp Hot-dip galvanized steel
fasteners Stainless steel
Weight 7.3 lb (3.3 kg)
Dimensions 15.4 x 2.9 x 1.3 inches (390 x 73 x 34 mm)
Mounting Mounts using the supplied fasteners.
Requires 2 x 850 10002 or 2 x 850 10003
mounting clamp listed below.
Recommended torque for M8 bolted connections: 8.8 Lb-Ft (12 Nm)
850 10006, 850 10002, 850 10003
3901
720.3
640.3 640.2 640.2
2800.5
34
7
3
R
1
0
9
0
0
.5
9
+1
0
Order Information:
Model Description
850 10006 Dual panel mounting kit
2 x 850 10002 Mounting clamp for 4.38.7 inch
(110220 mm) OD steel mast
11.9 lb (5.4 kg).
2 x 850 10003 Mounting clamp for 8.315 inch
(210380 mm) OD steel mast.
21.2 lb (9.6 kg).
322
Mounting Kit Options for Omni & Directional Antennas
* Requires 2 each MKPX-2
*
*
*
*
*
*
323
Mounting Kits Mounting Kit Options for Omni & Directional Antennas
MKPX-9
MKPX-2
MKPP-23
MKPS-1, MKPS-2, MKPS-3,
MKPS-4, MKPS-5
MKPS-13
MKPP-23
MKPS-1, MKPS-2,
MKPS-3, MKPS-4,
MKPS-5, MKPS-13
MKPX-2, MKPX-9
324
Tilt Mount Kits
Tilt Kit Options for Omni & Directional Antennas
MKTB-3*
MKTB-1
MKTB-1
MKTB-3
* Phantom mast attachment
bracket shown is part of the
associated yagi antenna
MKPX-3, MKPX-4,
MKPX-5, MKPX-6
MKPX-10
MKPX-11, MKPX-12
MKPX-3, MKPX-4,
MKPX-5, MKPX-6,
MKPX-10, MKPX-11,
MKPX-12
325
Panel Antenna Azimuth Adjustment Kit 850 10014, 850 10015
Specications: 850 10014 850 10015 850 10016 850 10017
Mounting surface Mast Mast Wall Wall
Number of brackets 2 2 2 2
Distance between bolts (A) 2.5 inches 2.8 inches 2.5 inches 2.8 inches
(64 mm) (72 mm) (64 mm) (72 mm)
Angular range 30 30 30 30
Weight 1.2 lbs 1.5 lbs 2.3 lbs 2.6 lbs
(0.55 kg) (0.7 kg) (1.05 kg) (1.2 kg)
Max. permissable static load per kit
X direction 2150 N 5100 N 2150 N 5100 N
Y direction 760 N 1350 N 760 N 1350 N
Supplied mounting hardware Antenna mounting hardware included Antenna mounting hardware included
Wall mounting hardware not included
850 10016, 850 10017
Y
X
g n i t n u o m l l a W g n i t n u o m e l o P
Hot-dip galvanized with stainless steel nuts.
A
Recommended torque for all fasteners: 14.75 ft-lb (20 Nm)
11106-A
936.3037
326
Technical Information
Advanced X-POL Antenna Standards .................................... 332
Calculating Downtilt ................................................................ 331
Calculating HPBW Touchdown Point ...................................... 333
Comparison of Mechanical and
Electrical Downtilt ............................................................. 334
Directional Antennas In Front of
Reecting Surfaces .......................................................... 337
Dual Polarized Base Station Antennas For
Polarization Diversity System ........................................... 329
Engineering Reference - Equations ....................................... 340
Formula For Estimating Gain For A Standard
Directional Dipole Array Using The
E & H Plane Patterns ....................................................... 331
Glossary ................................................................................. 344
Isolation Between Dipoles ...................................................... 339
Model Number Cross Reference ............................................ iii
Panel Antenna Test Specications ......................................... xiv
Radiation Patterns for Side-mounted Omni Antennas ........... 336
Signal Distribution of Power Splitters ..................................... 335
Signal Distribution of Power Taps ........................................... 335
Wind Survival Rating .............................................................. 333
327
T
e
c
h
n
i
c
a
l
I
n
f
o
r
m
a
t
i
o
n
I N F O R M A T I O N
328
329
2
69 69
Technical Information
The space diversity antenna conguration certainly provides
good electrical results, but the number of antennas required is a
negative factor with regard to the resulting optical appearance, the
increased space requirements and the greater amount of mechani-
cal hardware and feeder cables needed.
In view of the difculties getting construction permits from the
authorities concerned and approval from property owners for
the installation of antenna systems, an advanced system with a
low-level optical impact had to be found.
Dual Polarized Base Station Antennas For
Polarization Diversity Systems
It is well known that in a cellular network, mobile phones have
considerably lower transmittal power than the transmitters of the
base stations. This means that the transmission from the mobile
phone to the base station (uplink) is much more unfavorable in
relation to the transmission from the base station to the mobile
phone (downlink). To compensate this, a way of improving the
quality of reception at base stations had to be found.
Due to the multi-path signal propagation of radio signals, which
occurs in urban areas, so called Space Diversity Reception has
been introduced which provides the best results in the eld.
Space Diversity Reception is based on the following
idea:
The signal transmitted by a mobile phone is reected in the propa-
gation eld and reaches the base station via different paths and
phase angles. As a result, the signal at the base station receiving
antenna is the sum or various vectors with different amplitudes,
phases and polarizations. If two receiving antennas are separated
horizontally from each other, (preferable to vertical separation),
then it is highly likely that one of them will provide the required
signal strength (principle of uncorrelated signals). A logic unit
ensures that the higher signal level of the two receiving antennas
is fed into the receiving systems.
Depending on the characteristics in the propagation area, the use
of a Space Diversity Receiving System will produce a diversity
gain of 3 to 5 dB, as compared to using only one single receiving
antenna.
Dual Polarized Base Station Antennas For
Polarization Diversity Systems (cont)
Extensive investigations and trials have shown that so-called Po-
larization diversity Reception is equivalent to or almost equivalent
to Space Diversity Reception. Polarization Diversity Reception
means that the reception levels of two orthogonally polarized
antennas are compared and then the stronger signal is led to the
receiver.
The clear development objective was to design dual-polarized
antennas that have the same outer dimensions as single polarized
antennas and with equivalent gain gures and radiation patterns.
The number of individual antennas can thereby be considerably
reduced, resulting in improved optical appearance, reduced space
requirements and with less mechanical hardware.
It can generally be said, that the isolation between neighboring
transmitting antennas, as well as between a transmit and a receive
antenna must amount to at least 30 dB in order to avoid:
interfering intermodulation products
blocking of the receivers
Fig. 1: Sector antenna system using Space Diversity
Reception - 3 antennas, 3 feeders
Rx
1
Tx Rx
2
Fig. 2: Sector antenna system with Polarization Diversity
Reception - 2 antennas, 3 feeders
Tx Rx
1
+ Rx
2
Tx
1
Fig. 3: Sector antenna system with Polarization Diversity
Reception using a duplex lter
1 antenna, 3 feeders, 1 duplexer
Duplexer
Rx
1
Rx
2
330
Technical Information
Isolation gures for various antenna arrangements are available
from Kathrein Scala Division.
Radiation patterns and half power beam widths of
X-pol antennas:
Vertically or horizontally polarized antennas show constant po-
larization regardless of the azimuth angle from which the antenna
is observed.
However the polarization of a 45 polarized antenna is not always
45, it varies with the azimuth angle.
Dual Polarized Base Station Antennas For
Polarization Diversity Systems (cont)
Fig. 4: X-polarized antenna for 2 transmitting and
2 receiving channels
1 antenna, 2 feeders, 2 duplexers
the activation of the transmitters VSWR monitoring system
by an adjacent transmitter
This requirement for 30 dB isolation also applies to dual-polar-
ized antennas. Initially dual-polarized antennas with horizontal
and vertical polarization were preferred since this antenna con-
cept easily provides the required 30 dB isolation gure between
the horizontally polarized system and the vertically polarized
system.
Practical results with horizontal / vertical dual-polarized antennas
are fairly positive. However, there is also a weakness.
Since the mobile antennas (i.e. on cars or mobile phones) mainly
operate in a vertically polarized mode, the propagation efciency
is more favorable to the vertical system of a horizontal/vertical
dual-polarized base station antenna than to the horizontal system.
Thus horizontal polarization is not really suitable for transmit-
ting purposes.
However, with +45/-45 dual-polarization antennas, both sys-
tems are equivalent with respect to their propagation efciency.
The two systems can therefore be used with good results for
transmit and receive applications. Furthermore, this antenna
concept allows simultaneous transmission from two transmitters
without the use of a transmitter combiner.
Dual Polarized Base Station Antennas For
Polarization Diversity Systems (cont)
Fig. 5: Varying polarization of a dipole set at a slant of
45
The vector of the radiated electrical eld strength
is fully described by a pair of orthogonal vector
components; in other words, the vector is described
by a rectangular coordinate system.
According to Fig. 6, any eld strength vector can be described
either by a coordinate system, dened by the E
v
- vector and the
E
H
- vector, or with the same preciseness by a coordinate system
dened by the E
+45
- vector and the E
-45
- vector.
This concept is easy to understand if one considers the angles
of orientation when a slanted dipole is viewed from different
perspectives.
A dipole, which is set at a slant of +45 when viewed from the
front, will appear to be vertically polarized when viewed from
the side and will then appear at a slant of -45 when viewed from
the rear.
Tx
1
Duplexer
Rx
1a
+Rx
2a
Tx
2
Duplexer
Rx
1b
+Rx
2b
+45 polarized
vertically polarized
-45 polarized
Dipole
Fig. 6: Separation of a vector E into orthogonal
components
vertical
+45
45
horizontal
E
E
+45
E
V
E
-45
E
H
-45
45-polarization: E
H
= E
V
= E
+45
-3dB, E
-45
=0
331
Technical Information
This means that the exactness of the 45 polarization of an x-polar-
ized antenna can be tested by measuring the radiation pattern in
vertical polarization and in horizontal polarization or, alternatively
by measuring the radiation pattern in +45 polarization and in
-45 polarization (Fig. 7 and Fig. 8).
If the eld strength vector is exactly +45, the co-polar value is
100% and the cross-polar value is 0%.
In other words, if the polarization is almost 45, the radiation
patterns measured in vertical polarization E
v
and in horizontal
polarization E
H
will also be quite close to each other, or referring
to the second coordinate system, the cross-polar value E
-45
of the
eld strength will be much smaller than the co-polar one E
+45
.
If the polarization is exactly 45, the half power beam widths
of the radiation patterns measured in vertical polarization and
in horizontal polarization are all of the same value.
Dual Polarized Base Station Antennas For
Polarization Diversity Systems (cont)
Fig. 7: Radiation pattern of a Kathrein Scala Division X-
polarized 65 Antenna, measured with vertical and
horizontal polarization.
Fig. 8: Radiation pattern of a Kathrein Scala Division
X-polarized 65 Antenna, measured with +45 and
-45 polarization.
Formula For Estimating Gain For A Standard
Directional Dipole Array Using The E & H
Plane Patterns
*Gain (dBi) @ 10 log (32400/EH)
E = E plane 3 dB beamwidth in degrees
H = H plane 3 dB beamwidth in degrees
Formula does not take into account losses for internal harnessing
and input connector losses.
Estimated harness loss 0.2 dB/meter of antenna length
Estimated connector loss 0.1 dB
Printed circuit antennas have higher losses causing less ef-
ciency.
*R. S. Elliot, Beamwidth and Directivity of Large Scanning Arrays
The Microwave Journal, January 1964
Calculating Downtilt
Example
1 mile = 5,280 ft
6.2 miles x 5,280 = 32,736 ft
2400 32, 736 = 0.0733138
tan
-1
(0.0733138) = 4.2 degrees
Formula
angle = tan
-1
(h
1
-h
2
)
(
d
)
Where: h
1
= Elevation of the base antenna (ft)
h
2
= Elevation of the mobile antenna (ft)
d = Distance (ft)
11,000 feet
8,600 feet
2,400 feet
6.2 miles
332
Technical Information
Kathrein X-Pol Panels 1800 MHz
Typical Cross Polar Ratio (CPR)
CPR CPR CPR
Half-power Main 30 60
Beam Width direction sector sector
65 20 dB 16 dB 14 dB
90 17 dB 13 dB 10 dB
Many of the X-Pol antennas on the market are of patch technology
on printed circuit boards for power-splitting purposes. Kathrein,
for many years, has used the proven dipole-type technology to-
gether with low-loss cable harnesses, which clearly offers more
opportunities for perfecting certain antenna characteristics.
We present the new, Kathrein Panels as our concept for the
800/900 MHz X-Pol antenna line. We adapted the excellent and
well proven mechanical design used in our line of 1800/1900
MHz antennas. Instead of a berglass cover screwed and sealed
to an aluminum back-plate, the radome now consists of a closed,
self-supporting berglass prole into which the metal parts of
Advanced X-POL Antenna Standards
Kathrein Scala Division X-Pol antennas for polarization diversity
represent the latest development stage in antenna technology. An
increasing number of network operators realize the advantage
of installing three dual +/-45 degree polarized antennas for a
complete three sector site, where previously six or nine vertically
polarized antennas had to be installed.
For polarization diversity to function properly it is very important
that the different polarized signals are as independent as possible
from each other (principle of uncorrelated signals). The most
important point is the Cross-polar ratio (CPR), i.e. the ratio of
the signal levels of similar polarizations compared to dissimilar
polarizations. The CPR should be quoted for the whole sector
width (+/-60 degree), not just for the main radiating direction.
The antenna gain is already considerably reduced at the sector
edges due to the horizontal pattern, therefore a CPR as high as
possible is desired. The system suppliers demand at least 10 dB
for +/-60 degree from the main direction. Kathrein Scala Division
X-Pol antennas more than full these requirements.
Kathrein X-Pol Panels 800/900 MHz
Typical Cross Polar Ratio (CPR)
CPR CPR CPR
Half-power Main 30 60
Beam Width direction sector sector
65 22 dB 20 dB 15 dB
90 20 dB 15 dB 12 dB
Advanced X-POL Antenna Standards (cont)
the antenna are inserted. There are no drill-holes at all in the
prole which is closed by two sealed end caps. This completely
closed design offers ideal permanent protection against environ-
mental inuences and also increases the mechanical stability of
the antennas.
Apart from the existing comprehensive range of X-Pol antennas
which can be found in our catalogues, we now also have low
gain versions for 800/900 MHz band with a length of 26 inches
(656 mm).
Advantages of Kathreins dipole X-Pol type antennas com-
pared to typical patch printed or circuit board solutions:
1. Excellent cross polar ratio over azimuth.
The dipole design delivers remarkable cross polar ratio not
only in the main direction but also across the complete sec-
tor.
2. Low intermodulation products.
Unlike printed circuit antennas, the intermodulation products
are typically -150 dBc (2X25 watts).
3. Low internal losses.
The cable harness provides a low loss power distribution,
which enables shorter antenna lengths.
4. High isolation.
Patent pending decoupling elements ensure an isolation
between the two inputs of a min. >30 dB (typically 35 dB).
5. Constant electrical performance under bad weather condi-
tions.
Due to the dipole design, rain, ice and snow have little ef-
fect on the electrical parameters such as VSWR, isolation
and cross polar ratio.
333
Technical Information
Calculating HPBW Touchdown Point
Formula*
Where: H = Height of antenna from the ground (ft)
HPBW = Vertical half-power beamwidth (deg)
DTA = Downtilt angle expressed as a positive
value (deg)
* This formula is for level terrain calculations only.
Distance =
HPBW
2
tan
( )
H
+DTA
Example
(70 2)+0 = 35
tan(35) = .7002
200 .7002 = 286 feet
70 degrees
200 feet
Ground
286 feet
Wind Survival Rating
As a safety precaution to our customers, we would like to point
out that certain risks may arise when products are used under
extraordinary operating conditions.
Wind Survival Ratings as shown in this catalog represent a me-
chanical design based on environmental conditions as stipulated
in TIA-222-G-2 (December 2009) and/or ETS 300 019-1-4 which
include the static mechanical load imposed on an antenna by wind
at maximum velocity. The static mechanical load f is found by
the formula as follows:
f=kAV
2
Where: f is the load
A is the projected area of the antenna
V is the wind velocity
k is a constant unique to each antenna
Once the load f is found the resulting stress is found for each an-
tenna with its mounting system. The stress at which failure occurs
corresponds to a wind speed which is termed Wind survival.
Operating conditions such as icing or exceptional dynamic stress
(such as strain caused by oscillating support structures) may ex-
ceed the survival rating and result in the breakage of the product
or even cause it to break away from its support and fall to the
ground. Please consider these facts during the site planning and
installation process.
334
Comparison of Mechanical and Electrical Downtilt
Mechanical Electrical
m
p
f
u
n
g
dB
3 4 5 6 7 8 9 10 15 20
60
58
56
54
52
50
48
46
44
K
o
p
p
e
l
d
m
p
f
u
n
g
dB
20 30 40 50 60 80 100 120
s
I
s
o
l
a
t
i
o
n
I
s
o
l
a
t
i
o
n
d
Ratio: Distance (d) / wave-length (L) Ratio: Distance (d) / wave-length (L)
Technical Information
340
Engineering Reference - Equations
where: = reection coefcient
Z
r
= impedance at reection
Z
o
= characteristic impedance (typically 50)
Voltage Reection Coefcient
=
Z
r
- Z
o
Z
r
+ Z
o
RSL
dB
to VSWR
VSWR =
( )
(
RSL
dB
20
+1
)
10
( )
(
RSL
dB
20
-1
)
10
VSWR to RSL
dB
RSL
dB
= 20Log
( )
VSWR-1
VSWR+1
where: r = VSWR
= reection coefcient
P
r
= reected power
P
i
= incident power
P
t
= transmitted power
Voltage Standing Wave Ratio (VSWR)
r
,
at frequency
,
Material
r
60 10
6
10
10
60 10
6
10
10
(V/inch)
Nylon 1 3.60 3.14 2.80 0.018 0.022 0.0110 400
Plexiglas 1 3.45 2.76 2.50 0.064 0.104 0.0050 990
Polyethylene 1 2.26 2.26 2.26 (<0.0002) 0.005 1200
Teon (22C) 1 2.10 2.10 2.10 (<0.005) 0.004 1500
Material
r
r
( /m) Depth of penetration for plane waves (m)
Silver 1 1 6.17 x 10
7
0.064/
f
Copper 1 1 5.8 x 10
7
0.066/
f
Aluminum 1 1 3.72 x 10
7
0.083/
f
Brass 1 1 1.6 x 10
7
0.013/
f
at frequency
Metals
Nonmetals
Material Parameters at 20C Table 1.1
where:
r
is relative dielectric from Table 1.1
Characteristic Impedance of Free Space (cont)
c =
o
= propagation velocity = 2.997925 x 10
8
m/s
( 3 x 10
8
m/s)
In free space the wavelength is:
For a nonmagnetic dielectric:
1
c
f
=
c
f
d
= =
r
r =
1 +
1 -
VSWR =
P
r
P
i
=
2
=
r - 1
r + 1 ( )
2
P
t
P
i
=1-
2
=
4r
(r + 1)
2
Admittance Y = GjX =
1 -
1 + ( )
1
Z
= Y
0
Impedance Z = RjX =
1 +
1 - ( )
1
Y
= Z
0
where:
o
= free space permeability
= 4.0 x 10
-7
(H/m)
o
= free space permitivity
= (F/m)
Characteristic Impedance of Free Space
(
10
9
36)
o
=
o
= 120 = 377
Technical Information
341
Engineering Reference - Equations (cont)
dBw to Watts
Watts = 10
Milliwatts = 10
(
dBw
10
)
(
dBw+30
10
)
dBm to Watts
Watts = 10
Milliwatts = 10
(
dBm-30
10
)
(
dBm
10
)
where: P
r
= received power
P
t
= transmitted power
R = separation distance
Friis Transmission Equation
= free space loss
Using effective areas
( )
P
r
P
t
=
4R
2
G
t
G
r
P
r
P
t
=
A
et
A
er
2
R
( )
4R
2
Quarter Wave Matching
Z = Z
o
Z
L
where: Z = line impedance
Z
o
= desired input impedance
Z
L
= given load impedance
Effective Aperature Related to Gain of Antenna
G
=
4A
em
2
A
em
=
2
4
G
Watts to dBm
dBw = 10 log
10
(Power Watts)
dBm = (10 log
10
(Power Watts))+30
Noise Factor
F =
( )
P
no
G
A
P
ni
=
SNR
IN
SNR
OUT
=
T
e
T
o
-1
NF = 10LogF
Noise Figure
F = F
1
+
Cascade Noise Factor
F
2
-1
G
A1
F
3
-1
G
A1
G
A1
+
+
Voltage Gain/Loss to dB
dB
(gain/loss)
= 20Log
10
(Gain or Loss)
dBm to Volts/Volts
Volts = Log
10
-1
( )
dBm-13
20
Volts = Log
10
-1
( )
dBm-107
20
dBw to Volts/Volts
Volts = Log
10
-1
( )
dBw-17
20
Volts = Log
10
-1
( )
dBw-137
20
Engineering Reference - Equations (cont)
Characteristic Impedance of Coaxial Line
where: a = inner diameter
b = outer diameter
r
= relative permeability (usually = 1)
r
= permitivity (dielectric constant)
as given in Table 1.1
a
Z
o
= 138 log
10
(
b
a
)
b
Technical Information
342
Freespace Path Loss
L = 96.6 + 20 log(d) + 20 log(f)
where: L = freespace path loss
d = distance in miles
f = frequency in GHz
Directive Antenna Gain
where: G = directive antenna gain
= horizontal beamwidth
= vertical beamwidth
41253
.
theoretical
G =
32400
.
corrected for efciencies
G =
(
Gain of Parabolic Antenna
where: G = parabolic antenna gain
K = eff L 55%
D = diameter in feet
= wavelength in feet
D
G = 10 logK
)
2
Beamwidth of Parabolic Antenna
where: = beamwidth
D = diameter in feet
= feet
70
D
=
Radio Horizon (in miles)
H = 2Tx
Rx
where: H = horizon
Tx = transmit height in feet
Rx = receive height in feet
0 10 20 30 40 50 60 70 80 90
-10
-8
-6
-4
-2
0
Scan Angle From Broadside,
N
o
r
m
a
l
i
z
e
d
D
i
r
e
c
t
i
v
i
t
y
,
d
B
2L
= 10
2L
= 100
Cos
Reprinted from Microwave Scanning Antennas, edited by R. C. Hansen, Vol. 1, p. 20, published by Peninsula Publishing, Los Altos, California.
Courtesy of R. C. Hansen
Engineering Reference - Equations (cont) Engineering Reference - Equations (cont)
Technical Information
343
Engineering Reference - Equations (cont)
10 20 30 40 50
Sidelobe Ratio, dB
B
e
a
m
B
r
o
a
d
e
n
i
n
g
Taylor one-parameter distribution
Courtesy of Dr. R. C. Hansen
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.0
Beam Broadening Versus Sidelobe Ratio
Technical Information
344
1XRTT a wireless telephone digital protocol.
3G Third Generation Wireless wireless telephone service
encompassing high speed data communications in addition
to voice communications.
AISG Antenna Standards Interface Group a global standards
organization whose objective is the establishment of open
control standards among manufacturers of base stations,
switches and base station antennas with remotely adjustable
downtilt.
AMPS Advanced Mobile Phone System an analog wireless
telephone protocol; also refers to the 824894 MHz wireless
phone allocation in the US.
Antenna The part of transmitting or receiving system that is
designed to radiate or to receive electromagnetic waves.
Array Antenna An antenna comprised of a number of identical
radiating elements in a regular arrangement and excited to
obtain a prescribed radiation pattern.
AWS A specic band of radio frequencies (spectrum) intended
to be used for next-generation wireless broadband services.
Most of the spectrum will be used for 3G mobile phone
service, using technologies such as WCDMA+HSDPA or
CDMA EV-DO.
Back Lobe A radiation lobe whose axis makes an angle of
approximately 180 degrees with respect to the beam axis
of an antenna.
Bandwidth (of an antenna) The range of frequencies within
which the performance of the antenna, with respect to some
characteristic, typically SWR or return loss, conforms to a
specied standard.
Beam (of an antenna) The major lobe of the radiation pattern
of an antenna.
CDMA Code Division Multiple Access a wireless telephone
digital protocol.
Circularly polarized plane wave A plane wave whose electric
eld vector is circularly polarized.
CPR Cross polar ratio a measure on a cross polarized antennas
ability to maintain polarization coherence over a 120
sector.
Dipole Antenna Any one of a class of antennas producing
a radiation pattern approximating that of an elementary
electric dipole.
Directional Antenna An antenna having the property of radiating
or receiving electromagnetic waves more effectively in some
directions than other.
Effective Radiated Power (ERP) In a given direction, the relative
gain of a transmitting antenna with respect to the maximum
directivity of halfwave dipole multiplied by the net power
accepted by the antenna from the connected transmitter.
E-plane, principal For a linearly polarized antenna, the plane
containing the electric eld vector and the direction of
maximum radiation.
Far-eld Pattern Any radiation pattern obtained in the fareld
of an antenna.
Far-eld Region That region of the eld of an antenna where
the angular eld distribution is essentially independent of the
distance from a specied point in the antenna region.
Freespace Loss The loss between two isotropic radiators in free
space, expressed as a power ratio.
Front-to-back Ratio The ratio of the maximum directivity of an
antenna to its directivity in a specied rearward direction.
Gain The ratio of the radiation intensity, in a given direction, to
the radiation intensity that would be obtained if the power
accepted by the antenna were radiated isotropically.
Gain Flatness Maximum deviation from the specied antenna
gain, over the entire specied bandwidth.
Ground Plane A conducting or reecting plane functioning to
image a radiating structure.
GSM Global System for Mobile Communications a wireless
telephone digital protocol.
HAAT Height above average terrain.
HalfPower Beamwidth In a radiation pattern cut containing the
direction of the maximum of a lobe, the angle between the
two directions in which the radiation intensity is onehalf
the maximum value
Horizontally Polarized Plane Wave A plane wave whose electric
eld vector is horizontally polarized.
H-plane For a linearly polarized antenna, the plane containing
the magnetic eld vector and the direction of maximum
radiation.
ISM band Industrial, Scientic, and Medical band; several
bands allocated in the US for unlicensed low power
communications devices, at 900 and 2400 MHz; uses include
wireless LANs, Bluetooth applications, wireless internet,
and spread spectrum pointtopoint services.
Isolation Between Antennas A measure of power transfer from
one antenna to another.
GLOSSARY
Technical Information
345
Loading The modication of a basic antenna such as a dipole
or monopole caused by the addition of conductors or
circuit elements that change the input impedance or current
distribution or both.
Log Periodic Antenna Any one of a class of antennas having
a structural geometry such that its impedance and radiation
characteristics repeat periodically as the logarithm of
frequency.
Major Lobe The radiation lobe containing the direction of
maximum radiation.
Minor Lobe Any radiation lobe except a major lobe.
Monopole An antenna, constructed above an imaging plane,
which produces a radiation pattern approximating that of an
electric dipole in the half space above the imaging plane.
Near-eld Region That portion of the neareld region of an
antenna between the fareld and the reactive portion of the
neareld region, wherein the angular eld distribution is
dependent upon distance from the antenna.
Null Fill Redirecting a portion of the signal from the Major Lobe
to ll the Nulls present between the Major Lobe and the
Lower Minor Lobes of the vertical radiation pattern. Used
to improve the coverage of area close in to the transmit site.
(Null Fill is typically represented as a percentage.)
Omnidirectional Antenna An antenna having an essentially
nondirectional pattern in a given plane of the antenna and
a directional pattern in any orthogonal plane.
PCS Personal Communication Services Digital wireless
services that include voice and data employing either the
TDMA, CDMA or GSM protocols; also refers to the 1850
1990 MHz wireless phone allocation in the US.
Polarization In a given direction from the antenna, the polarization
of the wave transmitted by the antenna.
Radiation Pattern The spatial distribution of a quantity that
characterizes the electromagnetic eld generated by an
antenna.
Radome A cover, usually intended for protecting an antenna from
the effects of its physical environment without degrading its
electrical performance.
Reactive Field Electric and magnetic elds surrounding an
antenna and resulting in the storage of electromagnetic
energy rather than in the radiation of electromagnetic
energy.
Reflector Antenna An antenna consisting of one or more
reecting surfaces and a radiating (receiving) feed system.
Relative Gain - The ratio of the gain of an antenna in a given
direction to the gain of a reference antenna.
RET Remote Electrical Tilt antenna systems having the ability
to adjust the tilt of the main beam from the horizontal to some
angle below the horizon by remote means.
Side Lobe Level The maximum relative directivity of a side
lobe with respect to the maximum directivity of an antenna,
usually expressed in decibels.
Side Lobe Suppression Any process, action, or adjustment to
reduce the level of the side lobes or to reduce the degradation
of the intended antenna system performance resulting from
the presence of side lobes.
TDMA Time Division Multiple Access a wireless telephone
digital protocol.
TMA Tower Mount Amplier a receiveonly preamplier used
to overcome cable losses in high frequency communications
systems.
USLS Upper sidelobe suppression techniques employed
to reduce the rst major upper sidelobe of an antenna to
prevent interference at distant cell sites employing common
channels.
UMTS Universal Mobile Telephone Service the ability for 3G
services to be provided on a worldwide basis using a common
protocol and overlapping radio spectrum.
VSWR Voltage Standing Wave Ratio.
Vertically polarized plane wave A plane wave whose electric
eld vector is vertically polarized.
V-pol Vertically polarized antennas.
WiFi Short for Wireless Fidelity, is a set of product compatibility
standards for wireless local area networks (WLAN) based on
the IEEE 802.11 specications.
WiMAX An acronym that stands for Worldwide Interoperability
for Microwave Access, is a certication mark for products
that pass conformity and interoperability tests for the IEEE
802.16 standards.
WLAN Wireless Local Area Network Ethernet or other
computer networking protocol deployed using RF instead
of cable connections from node to node.
X-pol Crosspolarized antennas; having independent radiating
elements at 45; used in diversity systems.
Yagi-Uda Antenna A linear end-re array consisting of a driven
element, a reflector element, and one or more director
elements.
Technical Information
GLOSSARY
346
Notes
347
Notes
348
Notes
Limited Warranty
Kathrein Inc., Scala Division, hereafter referred to as the Seller, warrants that its products
are transferred rightfully and with good title, that its products are free from any lawful
security interest or other lien or encumbrance unknown to Buyer. Seller warrants its products
to be free of defects in workmanship and materials that arise under proper and normal use
and service for a period of ve years from date of original shipment. Broadcast products
and accessories manufactured by Kathrein-Werke KG and sold by Seller are covered by
the above limited warranty but for a period of two years. Products manufactured by others
are covered only by the warranties, if any, issued by their respective manufacturers and
Seller assumes no liability or responsibility of any kind for these goods. Damage caused
by wind, ice, re, lightning, improper installation or use, unauthorized disassembly or
modications or repairs, improper handling or any other causes beyond the control of Seller
are not covered by this limited warranty. In the event that Seller determines that defects have
occurred, Buyers exclusive remedy hereunder is limited to Sellers repair or replacement
(either at its plant or at such other place as may be agreed upon between Seller and Buyer)
of such defects at no cost to Buyer. Transportation costs to Sellers plant or designated
facility in connection with the return of products alleged to be defective shall be paid by
Buyer. Products supplied as warranty replacements and products repaired under warranty
are covered for the balance of the original warranty period or for a period of 90 days after
shipment from Seller, whichever is longer. SELLER MAKES NO WARRANTY EXPRESS
OR IMPLIED OTHER THAN AS STATED ABOVE. EXPRESSLY EXCLUDED ARE
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PURPOSE. THE FOREGOING SHALL CONSTITUTE ALL OF SELLERS LIABILITY
UNDER THIS WARRANTY WITH RESPECT TO THE PRODUCTS. IN NO EVENT
SHALL SELLER BE LIABLE FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL
DAMAGES, INSTALLATION COSTS, LOST REVENUE OR PROFITS, OR ANY
OTHER COSTS OF ANY NATURE AS A RESULT OF THE USE OF PRODUCTS
MANUFACTURED BY THE SELLER, WHETHER USED IN ACCORDANCE WITH
THE INSTRUCTIONS OR NOT UNDER NO CIRCUMSTANCES SHALL SELLERS
LIABILITY TO BUYER UNDER THIS WARRANTY EXCEED THE ACTUAL SALES
PRICE OF THE PRODUCTS PROVIDED HEREUNDER. No representative is authorized
to assume for Seller any other liability in connection with the products.