Академический Документы
Профессиональный Документы
Культура Документы
Revision History
Revision -001 Revision History First release of the Intel Desktop Board D525MW Product Guide Date June 2010
Disclaimer
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intels Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Intel Desktop Board D525MW may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling 1-800-548-4725.
Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries. * Other names and brands may be claimed as the property of others.
Preface
This Product Guide gives information about board layout, component installation, and regulatory requirements for Intel Desktop Board D525MW.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for general audiences.
Intended Uses
All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported without further evaluation by Intel.
Document Organization
The chapters in this Product Guide are arranged as follows: 1 2 3 A B Desktop Board Features: a summary of product features Installing and Replacing Desktop Board Components: instructions on how to install the Desktop Board and other hardware components Updating the BIOS: a description of how to update the BIOS BIOS Error Messages: information about BIOS error messages and beep codes Regulatory Compliance: safety and EMC regulations and product certifications
Conventions
The following conventions are used in this manual:
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
iii
Terminology
The table below gives descriptions to some common terms used in the product guide.
Term GB GHz KB MB Mbit MHz Description Gigabyte (1,073,741,824 bytes) Gigahertz (one billion hertz) Kilobyte (1024 bytes) Megabyte (1,048,576 bytes) Megabit (1,048,576 bits) Megahertz (one million hertz)
iv
Contents
1 Desktop Board Features
Desktop Board Components.................................................................................11 Processor..........................................................................................................13 System Memory.................................................................................................13 Integrated Graphics Subsystem ...........................................................................14 Intel NM10 Express Chipset ...............................................................................14 Operating System Support ..................................................................................14 Onboard Audio Subsystem ..................................................................................14 Legacy Input/Output (I/O) Controller ....................................................................16 LAN Subsystem .................................................................................................16 USB 2.0 Support ................................................................................................17 SATA Interface ..................................................................................................17 Expandability.....................................................................................................17 BIOS ................................................................................................................18 PCI/PCI Express Auto Configuration ..............................................................18 Security Passwords .....................................................................................18 Power Management Features ...............................................................................19 ACPI .........................................................................................................19 Hardware Support ......................................................................................19 Battery .............................................................................................................22 Real-Time Clock.................................................................................................22
B Regulatory Compliance
Safety Standards ...............................................................................................53 Battery Caution ..........................................................................................53 European Union Declaration of Conformity Statement..............................................54 Product Ecology Statements ................................................................................55 Recycling Considerations .............................................................................55 China RoHS ...............................................................................................58 EMC Regulations ................................................................................................59 FCC Declaration of Conformity ......................................................................59 Canadian Department of Communications Compliance Statement ......................60 Japan VCCI Statement ................................................................................60 Korea Class B Statement .............................................................................61 Ensure Electromagnetic Compatibility (EMC) Compliance ..................................61 Product Certifications..........................................................................................62 Board-Level Certifications ............................................................................62 Chassis- and Component-Level Certifications ..................................................63 ENERGY STAR*, e-Standby, and ErP Compliance ....................................................64
vi
Contents
Figures
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Intel Desktop Board D525MW Components ......................................................11 Back Panel Audio Connectors .........................................................................15 LAN Status LEDs ..........................................................................................16 Location of the Standby Power Indicator ..........................................................20 Installing the I/O Shield ................................................................................26 Intel Desktop Board D525MW Mounting Screw Holes .........................................27 Installing System Memory .............................................................................28 Connecting the Serial ATA Cable .....................................................................29 Installing a Full-Mini Card Wireless LAN Card ....................................................30 Installing a Half-Mini Card Wireless LAN Card ...................................................31 Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device) ..............32 Internal Headers ..........................................................................................33 Location of the Chassis Fan Header .................................................................37 Connecting Power Supply Cables ....................................................................38 BIOS Configuration Jumper Block....................................................................39 Removing the Battery ...................................................................................45 Intel Desktop Board D525MW China RoHS Material Self Declaration Table.............58
Tables
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. Feature Summary.......................................................................................... 9 Intel Desktop Board D525MW Components ......................................................12 Audio Jack Support .......................................................................................15 LAN Status LEDs ..........................................................................................17 Front Panel Audio Header for Intel HD Audio.....................................................34 Front Panel Audio Header for AC 97 Audio .......................................................34 S/PDIF Header .............................................................................................34 Serial Port Header (COM 1) ............................................................................35 Front Panel USB Header ................................................................................35 Front Panel USB Header with Intel Z-U130 USB Solid-State Drive or Compatible Device Support ............................................................................35 Front Panel Header Signal Names ...................................................................36 Front Panel Wireless Activity LED Header .........................................................36 Jumper Settings for the BIOS Setup Program Modes..........................................40 AcceptableDrives/Media Types for BIOS Recovery .............................................49 BIOS Beep Codes .........................................................................................51 BIOS Front-panel Power LED Blink Codes .........................................................52 POST Error Messages ....................................................................................52 Safety Standards..........................................................................................53 EMC Regulations...........................................................................................59 Regulatory Compliance Marks.........................................................................62 ENERGY STAR Requirements ..........................................................................64
vii
viii
LAN Support
BIOS
Intel BIOS Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and SMBIOS Support for PCI Local Bus Specification, Revision 2.3 Support for Advanced Configuration and Power Interface (ACPI) Wake on USB, PCI, PCI Express, PS/2, LAN, serial, and front panel
For more information on Intel Desktop Board D525MW consult the following online resources:
To find information about Intel Desktop Board D525MW Desktop Board Support Available configurations for Intel Desktop Board D525MW Chipset information BIOS and driver updates Integration information Visit this World Wide Web site: http://www.intel.com/products/motherboard/index.htm http://www.intel.com/p/en_US/support?iid=hdr+support http://ark.intel.com
10
11
12
Processor
Intel Desktop Board D525MW includes a passively-cooled, dual-core Intel Atom processor with integrated graphics and memory controller. The processor is soldered to the Desktop Board and is not customer upgradeable.
NOTE
The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness.
System Memory
NOTE
To be fully compliant with all applicable Intel SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up. The BIOS will attempt to configure the memory controller for normal operation. The Desktop Board has two 204-pin DDR3 SO-DIMM sockets with gold-plated contacts. These sockets support: Support for DDR3 800/1066/1333 MHz SO-DIMMs (DDR3 1066 MHz and DDR3 1333 MHz SO-DIMMs operate at 800 MHz only) Serial Presence Detect (SPD) memory only Non-ECC memory Up to 4 GB of memory
13
14
The front/back panel audio connectors are configurable through the audio device drivers. Table 3 lists the supported functions of the front panel and back panel jacks. Table 3. Audio Jack Support
Line Audio Jack Front panel Green Front panel Pink Back panel Blue Back panel Green Back panel Pink In No No Yes No No Line/ Front Out Yes No No Yes No No No Yes No No Rear Out Center/ LFE No No No No Yes Microphone No Yes No No Yes Headphones Yes No No Yes No
Figure 2 shows the default assignment of the back panel audio connectors.
Item A B C
NOTE
The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output.
15
The BIOS Setup program provides configuration options for the legacy I/O controller.
LAN Subsystem
The LAN subsystem consists of the following: Intel NM10 Express Chipset Realtek 8111E Gigabit Ethernet Controller for 10/100/1000 Mbits/s Ethernet LAN connectivity RJ-45 LAN connector with integrated status LEDs CSMA/CD protocol engine LAN connect interface that supports the ethernet controller PCI bus power management Supports ACPI technology Supports LAN wake capabilities
LAN drivers are available from Intels World Wide Web site at http://downloadcenter.intel.com/. Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 3). These LEDs indicate the operating states of the LAN.
16
Table 4 describes the LED states when the board is powered up and the LAN subsystem is operating. Table 4. LAN Status LEDs
LED Activity (A) Speed (B) LED Color Green N/A Green Yellow LED State Blinking Off On On Indicates LAN activity is occurring. 10 Mbits/s data rate is selected. 100 Mbits/s data rate is selected. 1000 Mbits/s data rate is selected.
NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device.
SATA Interface
The Desktop Board supports two SATA channels (3.0 Gb/s) that support one device per channel. The SATA controller supports IDE and ACHI configuration and can operate in both legacy and native modes.
Expandability
The Desktop Board provides the following expansion capability: One PCI connector. The connector can support either a single PCI add-in card or a single- or dual-slot PCI riser card. One PCI Express Full-Mini Card slot.
17
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI and SATA auto-configuration utilities, and the video BIOS.
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup and for booting the computer, with the following restrictions: The supervisor password gives unrestricted access to view and change all Setup options. If only the supervisor password is set, pressing <Enter> at the password prompt of Setup gives the user restricted access to Setup. If both the supervisor and user passwords are set, you must enter either the supervisor password or the user password to access Setup. Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered. Setting a user password restricts who can boot the computer. The password prompt is displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, you can enter either password to boot the computer.
For instructions on resetting the password, see Clearing Passwords on page 40.
18
ACPI
ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with the Desktop Board requires an operating system that provides full ACPI support.
Hardware Support
Fan Header
The Desktop Board has a 3-pin chassis fan header. See Figure 13 on page 37 for the location of the chassis fan header.
19
Figure 4. Location of the Standby Power Indicator For more information on standby current requirements for the Desktop Board, refer to the Technical Product Specification on the Intel Desktop D525MW web page at http://www.intel.com/products/motherboard/D525MW/index.htm.
20
Upon detecting the configured wake packet type, the LAN subsystem asserts a wakeup signal that powers up the computer.
NOTE
Wake from USB requires the use of a USB peripheral that supports wake from USB.
21
Battery
A coin-cell battery on the Desktop Board keeps the values in CMOS RAM and the clock current when the computer is turned off. Go to page 41 for instructions on how to replace the battery.
Real-Time Clock
The Desktop Board includes a time-of-day clock and a 100-year calendar. The coincell battery keeps the clock current when the computer is turned off.
22
23
CAUTION
Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board. All responsibility for determining the adequacy of any thermal or system design remains solely with the reader. Intel makes no warranties or representations that merely following the instructions presented in this document will result in a system with adequate thermal performance.
CAUTION
Ensure that the ambient temperature does not exceed the boards maximum operating temperature. Failure to do so could cause components to exceed their maximum case temperature and malfunction. For information about the maximum operating temperature, see the environmental specifications in the Intel Desktop Board Technical Product Specification.
CAUTION
The board is designed to be passively cooled on a properly ventilated chassis. Chassis venting locations are recommended over the processor, voltage regulator, and system memory areas for maximum heat dissipation effectiveness. Ensure that proper airflow is maintained around the processor, processor voltage regulator circuit, and the DIMM. Failure to do so may result in damage to these components.
CAUTION
A thermal rating of 85 oC is required for the DIMMs used on this board.
24
Installation Precautions
When you install and test the Intel Desktop Board, observe all warnings and cautions in the installation instructions. To avoid injury, be careful of: Sharp pins on connectors or headers Sharp pins on printed circuit assemblies Rough edges and sharp corners on the chassis Hot components (such as voltage regulators and heat sinks) Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel.
25
26
27
Figure 7. Installing System Memory To remove an SO-DIMM from a socket, gently spread the sockets retention arms (Figure 7, C) to disengage them from the SO-DIMM.
28
29
Installing a Wireless LAN Card in the PCI Express Mini Card Slot
A wireless LAN card can be installed in the Desktop Boards PCI Express Mini Card slot. To install a Full-Mini Card wireless LAN card, see Figure 9 and follow these steps: 1. Observe the precautions in "Before You Begin" on page 23. 2. Insert the wireless LAN card into the PCI Express Mini Card connector (Figure 9, A) at a slightly upward angle. 3. Align the cards mounting holes over the boards steel mounting posts (Figure 9, B) and attach the card with the supplied screws. 4. Attach your systems antenna wires to the connectors (Figure 9, C) on the wireless LAN card as shown.
30
To install a Half-Mini Card wireless LAN card, see Figure 10 and follow these steps: 1. Observe the precautions in "Before You Begin" on page 23. 2. Insert the plastic Half-Mini Card latch in the mounting holes as shown in Figure 10, A. 3. Insert the wireless LAN card into the PCI Express Mini Card connector (Figure 10, B) at a slightly upward angle. 4. Align the cards mounting holes (Figure 10, C) with the plastic latch and snap it into place. 5. Attach your systems antenna wires to the connectors (Figure 10, D) on the wireless LAN card as shown.
31
NOTE
External antennas can be connected through the I/O shield by removing one or both of the cut-outs on the I/O shield.
Figure 11. Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device)
32
33
34
Pin 2 4 6 8 10
Signal Name
+5 VDC DD+ Ground No Connect
Table 10. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive or Compatible Device Support
Pin 1 3 5 7 9 Signal Name
+5 VDC DD+ Ground KEY (no pin)
Pin 2 4 6 8 10
Signal Name
No Connect No Connect No Connect No Connect LED#
35
36
37
Figure 14. Connecting Power Supply Cables 1. Observe the precautions in "Before You Begin" on page 23. 2. Connect the main power supply cable to the 2 x 12 pin connector (Figure 14, B). 3. Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin connector (Figure 14, A).
38
Figure 15. BIOS Configuration Jumper Block The three-pin BIOS configuration jumper block enables board operating modes. Table 13 shows the jumper settings for each of the available modes.
39
Figure 15 shows the location of the Desktop Boards BIOS configuration jumper block. Table 13. Jumper Settings for the BIOS Setup Program Modes
Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting.
Configure (2-3)
After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords.
Recovery (None)
The BIOS recovers data from a recovery diskette in the event of a failed BIOS update.
Clearing Passwords
This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computers power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 15). 5. Place the jumper on pins 2-3 as shown below.
6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. 7. The computer starts the Setup program. Setup displays the Maintenance menu. 8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press <Enter>. Setup displays the maintenance menu again. 9. Press <F10> to save the current values and exit Setup. 10. Turn off the computer. Disconnect the computers power cord from the AC power source. 11. Remove the computer cover.
40
12. To restore normal operation, place the jumper on pins 1-2 as shown below.
13. Replace the cover, plug in the computer, and turn on the computer.
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.
PRCAUTION
Risque d'explosion si la pile usage est remplace par une pile de type incorrect. Les piles usages doivent tre recycles dans la mesure du possible. La mise au rebut des piles usages doit respecter les rglementations locales en vigueur en matire de protection de l'environnement.
FORHOLDSREGEL
Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier br om muligt genbruges. Bortskaffelse af brugte batterier br foreg i overensstemmelse med gldende miljlovgivning.
OBS!
Det kan oppst eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier br kastes i henhold til gjeldende miljlovgivning.
VIKTIGT!
Risk fr explosion om batteriet erstts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljvrdsbestmmelserna.
VARO
Rjhdysvaara, jos pariston tyyppi on vr. Paristot on kierrtettv, jos se on mahdollista. Kytetyt paristot on hvitettv paikallisten ympristmrysten mukaisesti.
41
VORSICHT
Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.
AVVERTIMENTO
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.
PRECAUCIN
Existe peligro de explosin si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante.
WAARSCHUWING
Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.
ATENO
Haver risco de exploso se a bateria for substituda por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminao de baterias usadas deve ser feita de acordo com as regulamentaes ambientais da regio.
ACIAROZNA
, . , , . .
UPOZORNN
V ppad vmny baterie za nesprvn druh me dojt k vbuchu. Je-li to mon, baterie by mly bt recyklovny. Baterie je teba zlikvidovat v souladu s mstnmi pedpisy o ivotnm prosted.
. . .
42
VIGYZAT
Ha a telepet nem a megfelel tpus telepre cserli, az felrobbanhat. A telepeket lehetsg szerint jra kell hasznostani. A hasznlt telepeket a helyi krnyezetvdelmi elrsoknak megfelelen kell kiselejtezni.
AWAS
Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan.
OSTRZEENIE
Istnieje niebezpieczestwo wybuchu w przypadku zastosowania niewaciwego typu baterii. Zuyte baterie naley w miar moliwoci utylizowa zgodnie z odpowiednimi przepisami ochrony rodowiska.
PRECAUIE
Risc de explozie, dac bateria este nlocuit cu un tip de baterie necorespunztor. Bateriile trebuie reciclate, dac este posibil. Depozitarea bateriilor uzate trebuie s respecte reglementrile locale privind protecia mediului.
. . , .
UPOZORNENIE
Ak batriu vymente za nesprvny typ, hroz nebezpeenstvo jej vbuchu. Batrie by sa mali poda monosti vdy recyklova. Likvidcia pouitch batri sa mus vykonva v slade s miestnymi predpismi na ochranu ivotnho prostredia.
POZOR
Zamenjava baterije z baterijo druganega tipa lahko povzroi eksplozijo. e je mogoe, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi.
43
UYARI
Yanl trde pil takldnda patlama riski vardr. Piller mmkn olduunda geri dntrlmelidir. Kullanlm piller, yerel evre yasalarna uygun olarak atlmaldr.
O
, . , . , .
44
1. Observe the precautions in "Before You Begin" (see page 23). 2. Turn off all peripheral devices connected to the computer. Disconnect the computers power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Locate the battery on the board (see Figure 16). 5. Push the battery retention clip aside and remove the battery from the connector as shown in Figure 16. Note the orientation of the + and - on the battery. 6. Install the new battery in the connector, making sure to orient the + and - correctly. 7. Replace the computer cover.
45
46
Updating the BIOS with the Intel Express BIOS Update Utility
With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment. The BIOS file is included in an automated update utility that combines the functionality of the Intel Flash Memory Update Utility and the ease of use of Windows-based installation wizards. To update the BIOS with the Intel Express BIOS Update utility: 1. Go to http://www.intel.com/p/en_US/support?iid=hdr+support. 2. Navigate to the Intel Desktop Board D525MW page, click [view] Latest BIOS updates, and select the Express BIOS Update utility file. 3. Download the file to your hard drive. (You can also save this file to a removable USB device. This is useful if you are updating the BIOS for multiple identical systems.) 4. Close all other applications. This step is required. Your system will be rebooted at the last Express BIOS Update window. 5. Double-click the executable file from the location on your hard drive where it was saved. This runs the update program. 6. Follow the instructions provided in the dialog boxes to complete the BIOS update.
47
You can obtain either of these files through your computer supplier or by navigating to the Intel Desktop Board D525MW page at http://www.intel.com/p/en_US/support?iid=hdr+support . Navigate to the Intel Desktop D525MW page, click [view] Latest BIOS updates, and select the Iflash BIOS Update utility file.
CAUTION
Do not interrupt the process or the system may not function properly.
NOTE
Review the instructions distributed with the update utility before attempting a BIOS update.
CAUTION
Do not interrupt the process or the system may not function properly. 1. Uncompress the BIOS update file and copy the .BIO file and IFLASH.EXE to a bootable USB flash drive or other bootable USB media. 2. Configure the BIOS or use the F10 key option during POST to boot to the USB device. 3. Manually run the IFLASH.EXE file from the USB device and manually update the BIOS.
48
NOTE
For more information about BIOS update and recovery, go to http://support.intel.com/support/motherboards/desktop/sb/CS-022312.htm.
49
50
Memory error
On-off (1.0 second each) three times, then 932 Hz a 2.5-second pause (off); the entire pattern repeats (beeps and pause) until the system is powered off. Alternate high and low beeps (1.0 second each) for eight beeps, followed by system shut down. High beep 2000 Hz Low beep 1500 Hz
51
Video error
Memory error
52
B Regulatory Compliance
This appendix contains the following regulatory compliance information for Intel Desktop Board D525MW: Safety standards European Union Declaration of Conformity statement Product Ecology statements Electromagnetic Compatibility (EMC) regulations Product certifications
Safety Standards
Intel Desktop Board D525MW complies with the safety standards stated in Table 18 when correctly installed in a compatible host system. Table 18. Safety Standards
Regulation CSA/UL 60950-1 EN 60950-1 IEC 60950-1 Title Information Technology Equipment Safety - Part 1: General Requirements (USA and Canada) Information Technology Equipment Safety - Part 1: General Requirements (European Union) Information Technology Equipment Safety - Part 1: General Requirements (International)
Battery Caution
There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery. For system safety certification, the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery. A suitable caution label is included with Intel Desktop Board D525MW.
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. For information about replacing the battery, go to page 41.
53
This product follows the provisions of the European Directives 2004/108/EC, 2006/95/EC and 2002/95/EC. etina Tento vrobek odpovd poadavkm evropskch smrnic 2004/108/EC, 2006/95/EC a 2002/95/EC. Dansk Dette produkt er i overensstemmelse med det europiske direktiv 2004/108/EC, 2006/95/EC & 2002/95/EC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004/108/EC, 2006/95/EC & 2002/95/EC. Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC, ja 2006/95/EC ja 2002/95/EC kehtestatud nuetele. Suomi Tm tuote noudattaa EU-direktiivin 2004/108/EC, 2006/95/EC & 2002/95/EC mryksi. Franais Ce produit est conforme aux exigences de la Directive Europenne 2004/108/EC, 2006/95/EC & 2002/95/EC. Deutsch Dieses Produkt entspricht den Bestimmungen der Europischen Richtlinie 2004/108/EC, 2006/95/EC & 2002/95/EC. 2004/108/EC, 2006/95/EC 2002/95/EC. Magyar E termk megfelel a 2004/108/EC, 2006/95/EC s 2002/95/EC Eurpai Irnyelv elrsainak. Icelandic essi vara stenst regluger Evrpska Efnahags Bandalagsins nmer 2004/108/EC, 2006/95/EC, & 2002/95/EC. Italiano Questo prodotto conforme alla Direttiva Europea 2004/108/EC, 2006/95/EC & 2002/95/EC. Latvieu is produkts atbilst Eiropas Direktvu 2004/108/EC, 2006/95/EC un 2002/95/EC noteikumiem. Lietuvi is produktas atitinka Europos direktyv 2004/108/EC, 2006/95/EC, ir 2002/95/EC nuostatas. Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC, 2006/95/EC u 2002/95/EC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC, 2006/95/EC & 2002/95/EC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC, 206/95/EC i 2002/95/EC.
54
Regulatory Compliance
Portuguese Este produto cumpre com as normas da Diretiva Europia 2004/108/EC, 2006/95/EC & 2002/95/EC. Espaol Este producto cumple con las normas del Directivo Europeo 2004/108/EC, 2006/95/EC & 2002/95/EC. Slovensky Tento produkt je v slade s ustanoveniami eurpskych direktv 2004/108/EC, 2006/95/EC a 2002/95/EC. Slovenina Izdelek je skladen z dolobami evropskih direktiv 2004/108/EC, 2006/95/EC in 2002/95/EC. Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC, 2006/95/EC & 2002/95/EC. Trke Bu rn, Avrupa Birliinin 2004/108/EC, 2006/95/EC ve 2002/95/EC ynergelerine uyar.
Recycling Considerations
As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intels branded products to return used products to selected locations for proper recycling. Please consult http://intel.com/intel/other/ehs/product_ecology for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc. Intel Product Recycling Program http://intel.com/intel/other/ehs/product_ecology
55
Deutsch Als Teil von Intels Engagement fr den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermglicht, gebrauchte Produkte an ausgewhlte Standorte fr ordnungsgemes Recycling zurckzugeben. Details zu diesem Programm, einschlielich der darin eingeschlossenen Produkte, verfgbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://intel.com/intel/other/ehs/product_ecology Espaol Como parte de su compromiso de responsabilidad medioambiental, Intel ha implantado el programa de reciclaje de productos Intel, que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado. Consulte la http://intel.com/intel/other/ehs/product_ecology para ver los detalles del programa, que incluye los productos que abarca, los lugares disponibles, instrucciones de envo, trminos y condiciones, etc. Franais Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en uvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits uss en les retournant des adresses spcifies. Visitez la page Web http://intel.com/intel/other/ehs/product_ecology pour en savoir plus sur ce programme, savoir les produits concerns, les adresses disponibles, les instructions d'expdition, les conditions gnrales, etc. http://intel.com/intel/ot her/ehs/product_ecology Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran, Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi-lokasi terpilih untuk dikitarkan semula dengan betul. Sila rujuk http://intel.com/intel/other/ehs/product_ecology untuk mendapatkan butirbutir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia, arahan penghantaran, terma & syarat, dsb.
56
Regulatory Compliance
Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos so reciclados de maneira adequada. Consulte o site http://intel.com/intel/other/ehs/product_ecology (em Ingls) para obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os locais disponveis, as instrues de envio, os termos e condies, etc. Russian , Intel Intel (Product Recycling Program) Intel . , - http://intel.com/intel/other/ehs/product_ecology , , , , .. Trke Intel, evre sorumluluuna bamllnn bir paras olarak, perakende tketicilerin Intel markal kullanlm rnlerini belirlenmi merkezlere iade edip uygun ekilde geri dntrmesini amalayan Intel rnleri Geri Dnm Programn uygulamaya koymutur. Bu programn rn kapsam, rn iade merkezleri, nakliye talimatlar, kaytlar ve artlar v.s dahil btn ayrntlarn grenmek iin ltfen http://intel.com/intel/other/ehs/product_ecology web sayfasna gidin.
57
China RoHS
Intel Desktop Board D525MW is a China RoHS-compliant product. The China Ministry of Information Industry (MII) stipulates that a material Self Declaration Table (SDT) must be included in a products user documentation. The SDT for Intel Desktop Board D525MW is shown in Figure 17.
Figure 17. Intel Desktop Board D525MW China RoHS Material Self Declaration Table
58
Regulatory Compliance
EMC Regulations
Intel Desktop Board D525MW complies with the EMC regulations stated in Table 19 when correctly installed in a compatible host system. Table 19. EMC Regulations
Regulation FCC 47 CFR Part 15, Subpart B ICES-003 EN55022 Title Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (USA) Interference-Causing Equipment Standard, Digital Apparatus. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) Information Technology Equipment Immunity Characteristics Limits and methods of measurement. (European Union) Australian Communications Authority, Standard for Electromagnetic Compatibility. (Australia and New Zealand) Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment. (International) Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement. (International) Voluntary Control for Interference by Information Technology Equipment. (Japan) Korean Communications Commission Framework Act on Telecommunications and Radio Waves Act. (South Korea) Bureau of Standards, Metrology and Inspection. (Taiwan)
59
and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the users authority to operate the equipment. Tested to comply with FCC standards for home or office use.
60
Regulatory Compliance
If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer.
61
Product Certifications
Board-Level Certifications
Intel Desktop Board D525MW has the regulatory compliance marks shown in Table 20. Table 20. Regulatory Compliance Marks
Description UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Mark
CE mark. Declaring compliance to European Union (EU) EMC directive, Low Voltage directive, and RoHS directive.
Australian Communications Authority (ACA) and New Zealand Radio Spectrum Management (NZ RSM) C-tick mark. Includes adjacent Intel supplier code number, N-232. Japan VCCI (Voluntary Control Council for Interference) mark.
S. Korea KCC (Korean Communications Commission) mark. Includes adjacent KCC certification number: CPU-D525MW (B).
Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025. Printed wiring board manufacturers recognition mark. Consists of a unique UL recognized manufacturers logo, along with a flammability rating (solder side). China RoHS/Environmentally Friendly Use Period Logo: This is an example of the symbol used on Intel Desktop Boards and associated collateral. The color of the mark may vary depending upon the application. The Environmental Friendly Usage Period (EFUP) for Intel Desktop Boards has been determined to be 10 years. V-0
62
Regulatory Compliance
63
Computer Type Desktop Computer Integrated Computer Desktop Computer Integrated Desktop Computer
Capability Adjustments With and without Wake On LAN (Sleep, Standby) With and without additional internal storage
v5.0 v5.0
Cat A under desktop conventional and desktop proxying operational mode weightings N/A
v5.0
Thin Client
For information about ENERGY STAR requirements and recommended configurations, go to http://www.intel.com/go/energystar. The Desktop Board also meets the following international requirements: Republic of Korea e-Standby program European Union Energy using Products (ErP) directive
64