Академический Документы
Профессиональный Документы
Культура Документы
525
With this design it is possible to use iglidur high performance plain bearings in locations where recommended housing bore tolerances are not possible.
Maintenance-free
When to use it? When a screw flanged bearing is sought When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing
When not to use it? When an additional angular compensation is required igubal Flange bearings, page 631 When a screw connection is not possible iglidur Clip bearings, page 503 When a large guide length is necessary iglidur G, page 61
Light weight
Temperature
+130 40 +90 50 +90 50 +250 100
GFL
A180FL
JFL
XFL
www.igus.co.uk/iglidur-flange
Material data for available materials: iglidur G page 61 iglidur A180 page 371 iglidur J page 89 iglidur X page 153
Installation
Depending on the requirements, different mounting types can be considered. For low radial loads, it is sufficient to mount iglidur flange bearings on one surface simply with two bolts. For higher radial loads, it advisable to support the iglidur flange bearing in a bore on the reinforced side facing the direction of the load. For this bore, large tolerances are permitted, since it serves only as additional support for the iglidur flange bearing. In order to achieve higher radial loads in the bearings, the iglidur flange bearing can be pressfit into a recommended housing bore. The additional bolts ensure the fit of the bearing in the housing. For the installation of the iglidur maintenance-free flange bearing, no special materials or tools are necessary.
igus (UK) Ltd. Northampton NN4 7PW | Phone +44 (0) 1604-677240 Fax -242 | www.igus.co.uk 527
Flange bearings
b1
d4 d7 d3 d6
b3
Order key
b2
GFL-10
R
d5
Dimensions [mm]
Part number GFL-10 GFL-12 GFL-14 GFL-16 GFL-18 GFL-20 GFL-25 GFL-30 GFL-35 A180FL-10 A180FL-12 A180FL-16 A180FL-20 A180FL-25 A180FL-30 A180FL-35 JFL-10 JFL-12 JFL-14 JFL-16 JFL-20 JFL-25 JFL-30 JFL-35 XFL-10 XFL-12 XFL-14 XFL-16 XFL-20 XFL-25 XFL-30 XFL-35 d1* 10 12 14 16 18 20 25 30 35 10 12 16 20 25 30 35 10 12 14 16 20 25 30 35 10 12 14 16 20 25 30 35
d1 d2
d2** 12 14 16 18 20 23 28 34 39 12 14 18 23 28 34 39 12 14 16 18 23 28 34 39 12 14 16 18 23 28 34 39
d3 30 36 42 48 54 60 75 90 95 30 36 48 60 75 90 95 30 36 42 48 60 75 90 95 30 36 42 48 60 75 90 95
d4 14 16 18 20 22 26 30 36 41 14 16 20 26 30 36 41 14 16 18 20 26 30 36 41 14 16 18 20 26 30 36 41
d5 15 18 21 24 27 30 35 40 55 15 18 24 30 35 40 55 15 18 21 24 30 35 40 55 15 18 21 24 30 35 40 55
d6 4.5 4.5 5.5 5.5 6.5 6.5 6.5 8.5 8.5 4.5 4.5 5.5 6.5 6.5 8.5 8.5 4.5 4.5 5.5 5.5 6.5 6.5 8.5 8.5 4.5 4.5 5.5 5.5 6.5 6.5 8.5 8.5
d7 22 26 30 34 39 44 55 66 77 22 26 34 44 55 66 77 22 26 30 34 44 55 66 77 22 26 30 34 44 55 66 77
b1 6 6 6 6 6 10 10 10 10 6 6 6 10 10 10 10 6 6 6 6 10 10 10 10 6 6 6 6 10 10 10 10
b2 2 2 2 2 2 3 3 3 3 2 2 2 3 3 3 3 2 2 2 2 3 3 3 3 2 2 2 2 3 3 3 3
b3 1 1 1 1 1 2 2 2 2 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2
R
(0.2)
4 4.5 5 5.5 7 7 8.5 10 12 4 4.5 5.5 7 8.5 10 12 4 4.5 5 5.5 7 8.5 10 12 4 4.5 5 5.5 7 8.5 10 12