Академический Документы
Профессиональный Документы
Культура Документы
able to:
Explain the menu of iManager T2000 for Ethernet Services
Page 1
Page 2
are available: tag aware, access, and hybrid. Tag Aware: When the port is set to be tag aware, the port transmits the packets with the Tag flag transparently and discards those without the Tag flag
Access: When the port is set to be access, the port attaches a Tag flag to the packets without Tag flag according to its VLAN ID and discards those with the Tag flag.
Hybrid: When the port is set to be hybrid, the port can process packets regardless of the Tag flag and attach a Tag flag to the packets without the Tag flag according to its VLAN ID.
Page 3
Packets Port Tag aware (In) Tag aware (Out) Access (In) Access (Out) Hybrid (In)
Tag flag Transmit transparently Transmit transparently discard Delete the Tag flag (default Vlan) Transmit transparently If Vlan is the same, delete the Tag flag, otherwise transmit transparently
Untag flag discard attach a Tag flag (default Vlan) attach a Tag flag (default Vlan)
Hybrid (Out)
Page 4
It can be set to auto-negotiation, 10 Mbit/s half/full-duplex, 100 Mbit/s half/full-duplex or 1 Gbit/s full-duplex. The Ethernet interfaces of the interconnected equipment should work under the same fixed working mode; otherwise, the packet may be lost and the rate may decrease, or the service may be completely interrupted upon large volume of traffic.
Port type:
There are two types: P and PE. Provider edge (PE) is the marginal port of the service provider. Provider (P) is the core network port of the service provider. Port type is needed when configuring EVPL and EVPLAN services.
Page 5
Set this item for the external port, 1522 bytes by default.
Mapping protocol:
Page 6
EPLAN: Ethernet Private LAN Service . EVPL: Ethernet Virtual Private Line Service. EVPLAN: Ethernet Virtual Private LAN Service.
G.8011 (G.ethsrv),
G.8012.1 (G.eota.1).
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 7
Page 8
the Point-to-Point EPL Service the MAC Shared EPL Service the VCTRUNK Shared EPL Service
Page 9
Engineering Requirements
Engineering Planning Configuration Process
Page 10
User
A B
Service requirement
Point-to-point Point-to-point
Source station
NE1 NE1
Sink station
NE5 NE5
Bandwidth
10 Mbit/s 40 Mbit/s
Engineering Requirements
STM-4two-fiber bidirectional nonprotection chain NE5
Page 11
Engineering Planning
Page 12
MAC1
MAC2
T2000 NE1 STM-16 two-fiber bidirectional MSP ring STM-4 two-fiber bidirectional nonprotection chain NE5 NE4
MAC1 MAC2
NE2
NE3 A VC-Trunk Company A Service Company B Service HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 13 B
Page 14
Page 15
MAC
VCTRUNK
VCTRUNK
MAC
A B
MAC1
MAC1 VCTRUNK1
VC4-4:VC12-1~VC12-5
10M
MAC2
SDH
VCTRUNK1
VC4-4:VC12-1~VC12-5
10M
MAC2
A B
40M
VCTRUNK2
VC-4-1:VC-3-1
VCTRUNK2
VC-4-1:VC-3-1
40M
NE1
NE5
Page 16
A
NE1 13-N1EFS4-1 VC4-4: VC12-1VC12-5 VCTRUNK1 (Tag aware) Auto negotiation Access 1 5 x VC-12 NE5 15-N1EFS4-1 VC4-4: VC12-1VC12-5 VCTRUNK1 (Tag aware) Auto negotiation Access 1
B
NE1 13-N1EFS4-2 VC4-1: VC3-1 VCTRUNK2 (Tag aware) Auto negotiation Access 2 1 x VC-3 NE5 15-N1EFS4-2 VC4-1: VC3-1 VCTRUNK2 (Tag aware) Auto negotiation Access 2
Page 17
VC-4-4
13-EFS4: VC-4-1
NE5 7-SL4-1
VC-4-4
Page 18
Configuration Process
Page 19
Right click
Page 20
Page 21
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Left click
Page 23
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 24
Left click
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Summary
Creating an Ethernet board Configuring Ethernet interfaces
Page 26
the Point-to-Point EPL Service the MAC Shared EPL Service the VCTRUNK Shared EPL Service
Page 27
Engineering Requirements
Engineering Planning
Configuration Process
Page 28
C
C
MAC Shared
MAC Shared
NE1
NE1
C(1)
C(2)
NE5
NE5
10 Mbit/s
10 Mbit/s
Engineering Requirements
T2000
NE1 NE2 STM-16 two-fiber bidirectional MSP ring NE4 NE3 STM-4two-fiber bidirectional nonprotection chain NE5
Page 29
Configuring the MAC Shared EPL Service : Step 1: Networking Diagram Step 2: Board Information of Each NE Step 3: Service Configuration Diagram of Each NE Step 4: Timeslot Allocation Diagram
Page 30
C(1)
MAC3
C(2)
MAC4
NE2
NE4
MAC1
NE5
MAC2
NE3 A B
VC-Trunk
C & C(1) Service C & C(2) Service HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 31
VCTRUNK
MAC
A B
MAC1
MAC1 VCTRUNK1
VC4-4:VC12-1~VC12-5
10M
MAC2
VCTRUNK1
VC4-4:VC12-1~VC12-5
10M
MAC2
A B
40M
VCTRUNK2
VC-4-1:VC-3-1
SDH
VCTRUNK2
VC-4-1:VC-3-1
40M
MAC3
MAC3
VCTRUNK3
VC4-4:VC12-6~VC12-10
VCTRUNK3
VC4-4:VC12-6~VC12-10
10M
MAC4
C1 C2
VCTRUNK4
VC4-4:VC12-11~VC12-15
VCTRUNK4
VC4-4:VC12-11~VC12-15
10M NE5
NE1
Page 32
C & C(1)
NE1 13-N1EFS4-3 VC4-4: VC12-6VC12-10 VCTRUNK3 (Tag aware) Auto negotiation Tag aware 3 5 x VC-12 NE5
C & C(2)
VC4-4: VC12-11VC12-15 VCTRUNK4 (Tag aware) Auto negotiation Tag aware 4 5 x VC-12
Auto negotiation
Access 3
Auto negotiation
Access 4
Page 33
VC-4-3
Forwared Add/Drop
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 34
Configuration Process
Step 1: Creating a board (None) Step 2: Configuring Ethernet interfaces Step 3: Configuring binding paths Step 4: Creating the MAC shared EPL service Step 5: Configuring committed access rate (CAR) (Optional Step 6: Configuring the cross-connect from Ethernet boards to SDH line boards
Notice: We dont need the first step because the Ethernet boards Have already been created.
Page 35
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 36
Left click
HUAWEI TECHNOLOGIES CO., LTD.
Left click
Page 38
Notice: These two steps are the same as that of the point-to-point EPL service, except that some
Page 39
Summary
Creating an Ethernet board Configuring Ethernet interfaces
Page 40
the Point-to-Point EPL Service the MAC Shared EPL Service the VCTRUNK Shared EPL Service
Page 41
Page 42
Service requirement
VCTRUNK Shared VCTRUNK Shared
Source station
NE2 NE2
Sink User
D E
Sink station
NE3 NE3
Bandwidth
300 Mbit/s 300 Mbit/s
T2000 NE1 NE2 STM-16 two-fiber bidirectional MSP ring NE4 NE3
Engineering Requirements
STM-4 two-fiber bidirectional non- protection chain NE5
Page 43
Page 44
NE1 T2000
MAC1
NE2
NE4 NE5
MAC2
NE3
MAC1 MAC2
VC-Trunk
D & D Service
E & E Service
Page 45
Page 46
D E
MAC1
300M
D E
MAC2
300M
VCTRUNK1
MAC2
300M
SDH
VC4-1:VC3-1~VC3-3 VC4-2:VC3-1~VC3-3
NE2
NE3
Page 47
D
NE2
E
13-N1EGS2-2
Source VCTRUNK
Working mode of source MAC port TAG flag of source MAC port VLAN ID of source MAC port
Bound bandwidth
Sink NE Sink board - port Sink timeslot 13-N1EGS2-1
6 x VC-3
NE3 13-N1EGS2-2
Sink VCTRUNK
Working mode of sink MAC port TAG flag of sink MAC port VLAN ID of sink MAC port
Page 48
Page 49
Configuration Process Step 1:Creating a board Step 2: Configuring Ethernet interfaces Step 3: Configuring binding paths
Summary
Creating an Ethernet board Configuring Ethernet interfaces
External Port: Basic Attributes, Tag Attribute Internal Port: Tag Attribute, LCAS Configuring binding paths: Configurable Ports, Level, Direction, Available VC4, timeslots Creating the VCTRUNK shared EPL service: Service Type, Service Direction, Ports, VLAN, TAG, Port Type Configuring committed access rate (CAR): CAR ID, Capacity, Ports Configuring the cross-connect from Ethernet boards to SDH line boards
Page 51
Page 52
Page 53
NE2
NE3
Source User Service requirement Source station Sink User Sink station
F(1) F(3) F(1) EPLAN EPLAN EPLAN NE2 NE4 NE2 F(2) F(2) F(3) NE3 NE3 NE4
Bandwidth
10 Mbit/s 10 Mbit/s 10 Mbit/s
Page 54
Engineering Planning
Step 1: Networking Diagram Step 2: Board Information of Each NE Step 3: Service Configuration Diagram of Each NE Step 4: Timeslot Allocation Diagram
Page 55
NE1 T2000
VCTRUNK1 VB MAC1 VB MAC1 VCTRUNK1
NE2 B
MAC1
NE4
MAC1
NE3
NE5
F(1)
MAC1
VCTRUNK1 VB
F(3) VC-Trunk
VCTRUNK2
F(2)
MAC1
Page 56
Page 57
Page 58
MAC
LP1MAC1
10M
MAC
VCTRUNK
LP2
F1
VCTRUNK1
VC4-4:VC12-1~VC12-5
VB1 NE2
F2
MAC1LP1
10M
VCTRUNK1
LP3
VC4-4:VC12-1~VC12-5
VB1 NE3
VC4-4:VC12-6~VC12-10
VCTRUNK2
VCTRUNK
LP2
VCTRUNK1
MAC
LP1MAC1
10M
F3
SDH
VC4-4:VC12-1~VC12-5
VB1 NE4
Page 59
F
NE3 14-N1EFS0-1 VC4-4: VC12-6VC12-10 VCTRUNK2 (Tag Aware) PE
Page 60
VB
VB1 VB1 VB1
VLAN ID
11 11 11
Forwarding port
LP1, LP2 LP1, LP2, LP3 LP1, LP2
Ring
Station NE1 NE4 NE2 NE3 Timeslot 12-SL16-1 7-SL16-112-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 VC-4-5 VC-12: 1-5 14-EFS0: VC4-4 Forward Add/Drop VC-12: 1-5 15-EFS0: VC4-4
Page 61
Page 62
Page 63
Right click
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 64
Left click
Left click
Left click
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 69
Summary
Creating an Ethernet board Configuring Ethernet interfaces
External Port: Basic Attributes, Tag Attribute, VLAN Internal Port: Tag Attribute, VLAN, LCAS Configuring binding paths: Configurable Ports, Level, Direction, Available VC4, timeslots Creating the EPLAN service: VB Port, Mount Port, Port Type, Binding Path Configuring the forwarding filter table VB Port, VLAN ID, forwarding port Configuring committed access rate (CAR): CAR ID, Capacity, Ports Configuring the cross-connect from Ethernet boards to SDH line boards
Page 70
Page 71
Page 72
T2000 NE1 NE2 STM-16 two-fiber bidirectional MSP ring NE4 NE3
Source User
D E
Service requirement
EVPL EVPL
Source station
NE2 NE2
Sink User
D E
Sink station
NE3 NE3
Bandwidth
100 Mbit/s 100 Mbit/s
Page 73
Page 74
NE1 T2000
MAC1
NE2
NE4 NE5
MAC2
NE3
MAC1 MAC2
VC-Trunk
Page 75
Page 76
Page 77
Attribute \ Service
Source NE Source board - port Source timeslot Source VCTRUNK Source VCTRUNK attribute Working mode of source MAC port TAG flag of source MAC port VLAN ID of source MAC port Source MAC attribute Bound bandwidth Sink NE Sink board - port Sink timeslot Sink VCTRUNK Sink VCTRUNK attribute Working mode of sink MAC port TAG flag of sink MAC port VLAN ID of sink MAC port Sink MAC attribute
D
NE2 14-N1EFS0-1
E
14-N1EFS0-2
VC4-4: VC12-1VC12-48 VCTRUNK1 (Tag Aware ) P 100M full duplex 100M full duplex Tag Aware Tag Aware 11 11 PE PE 48 x VC-12 NE3 14-N1EFS0-1 14-N1EFS0-2 VC4-4: VC12-1VC12-48 VCTRUNK1 (Tag Aware ) P 100M full duplex 100M full duplex Tag Aware Tag Aware 11 11 PE PE
Page 78
12-SL16-1 7-SL16-1
VC4-4
14EFS0: VC4-4
Forward
Add/Drop
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 79
Page 80
Page 81
Left click
Right click
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 82
Left click
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 84
Step 5: Configuring committed access rate (CAR) (Optional ) Step 6: Configuring the cross-connect from Ethernet boards to SDH line boards
Notice: These two steps are the same as that of the EPL service, except that some parameters are different.
Page 85
Summary
Creating an Ethernet board Configuring Ethernet interfaces
External Port: Basic Attributes, Tag Attribute, VLAN Internal Port: Tag Attribute, VLAN, LCAS, MPLS
Configuring binding paths:
Service Type, Service Direction, Ports, TAG, VLAN, Tunnel, VC, Port Type, Encapsulation Format
Configuring committed access rate (CAR):
Thank You
www.huawei.com