Академический Документы
Профессиональный Документы
Культура Документы
ISSUE2.0
www.huawei.com
References
3GPP TS 25.413 3GPP TS 23.110 HUAWEI SGSN9810 Serving GPRS Support Node Operation Manual Data Configuration
Page1
Objectives
Configure the data for the Iu over Asynchronous Transfer Mode (ATM) interface.
Configure the data for the Iu over Internet Protocol (IP) interface.
Page2
Contents
1. Basic Concepts
Page3
Iu Interface
The Iu interface is located between the serving GPRS support node (SGSN) and the radio network controller (RNC). On a UMTS network, the Iu interface is mandatory.
The Iu interface protocol stack consists of the user plane and control plane.
The Iu user plane uses the GPRS Tunneling Protocol-User Plane (GTP-U) protocol.
Page4
GTP-U UDP
IP
ATM
Data Link
ATM
Data Link
Physical Layer
Physical Layer
Page5
RANAP
Broadband MTP
The broadband Message Transfer Part (MTP) is implemented by the MTP3 User Adaptation (M3UA) or Message Transfer Part layer 3broadband (MTP3B). The signaling messages of the upper layer are routed and forwarded through broadband MTP.
GTP-U
The GTP-U protocol uses the tunnel to transmit signaling or user data.
Page6
SCCP
MTP3B SAAL ATM/PHY
SCCP
M3UA SCTP PFP/PFI IP/L2/L1 PFP/PFI
HY
Page7
Contents
1. Basic Concepts
Page8
Iu over ATM
RANAP SCCP MTP3B SAAL(AAL5)
MTP3B link SAAL link PVC exchange ATM backbone network
ATM
ATM
GTP_U
IPOA
PVC exchange
GTP_U
UDP
IP
UDP
IP
Page9
AAL5
AAL5
Negotiation Data
Board Subrack Slot Front/ba ck ECU EPU 0 0 0/1 (Active/Standby) 12/13 (Active/Standby) PFI 0 12/13 Back AIC/AIC Front Front Subboard
Board PFI
Page10
Negotiation Data
PVC traffic parameters
Item
User plane Control plane
Service Type
Uncertain rate Stationary rate
Peak Rate
100000 3708
User plane
SGSN
IP address of the user plane IP address of IPoA VPI/VCI
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.
RNC
100.1.1.1
217.164.95.65
10.110.0.1/24 1/200
10.110.0.2/24
Page11
Negotiation Data
Control plane
SGSN
PLMN ID 46000
RNC
RNC ID
Signaling point code (SPC) VPI/VCI of MTP3B link1 A00
1234
401 1/100
1/101
0 1
Page12
Configuration Steps
Configuring Boards and Optical Interfaces
Performed on the CGP or SGSN CGP SGSN CGP
Step 1 2 3
Operation Configure the ECU. Add ECU-related process groups. Activate the port.
Page13
Configuration Steps
Configuring Control Plane
Step 4 Operation Command SET SIGATTR
ADD MTP3BOPC ADD MTP3BDPC ADD MTP3BLKS ADD MTP3BRT ADD TRAFFIC ADD MTP3BLNK SET MTP3BTMR
Configuration Steps
Step Operation Command Configure the signaling connection control part (SCCP). 12 13 14 Configure an OPC of the SCCP. Configure a DPC of the SCCP. Configure the subsystem number of the SCCP. Configure the RNC. 15 16 Configure the RNC information. Configure the 3G paging table. ADD RNC ADD IUPAGING
ADD SCCPOPC
ADD SCCPDPC ADD SCCPSSN
17
ADD RNCPFLNK
Page15
Configuration Steps
Configuring User Plane
Step 18 19 (Optional) 20 21 Operation Set the IP address for the Iu interface. Set traffic parameters. Configure an IPoA link destined for the RNC. Configure the route to the RNC user plane. Configure the mapping between the RNC and the UGFU. Command ADD IFIP ADD TRAFFIC ADD IPOA ADD IPRT
22 (Optional)
ADD RNCPFLNK
Page16
ADD BRD:
FBRDHTYP=UPBA3, APPTYPE=ECU;
Page17
ADD PROCESSGRP:
Page18
ADD BRD:
Configure the EPI, the PFI in the back slot, and the relevant
subboards.
ADD BRD: SRN=0, SN=12, METYPE=SGSN, FBRDHTYP=MSPB0, BBRDHTYP=PFIA0, APPTYPE=EPU, BUPDBRDTYPE=AIC, BDOWNDBRDTYPE=AIC;
ADD BRD: SRN=0, SN=13, METYPE=SGSN, FBRDHTYP=MSPB0, BBRDHTYP=PFIA0, APPTYPE=EPU, BUPDBRDTYPE=AIC, BDOWNDBRDTYPE=AIC;
Page19
ADD PROCESSGRP:
Set the two EPUs at SRN 0 and SN 12, and SRN 0 and SN 13
to active and standby, and add EPU-related process groups on the EPU.
Page20
ACT PORT:
Activate the port of the SRN 0 and SN 12, and SRN0 and SN 13.
ACT PORT: SRN=0, SN=12, PORTID=1; ACT PORT: SRN=0, SN=13, PORTID=1;
MOD PORT:
Page21
100.1.1.1
217.164.95.65
RNC
Optical cable
SGSN
Logical IP
Page22
SET SIGATTR
Set or modify the signaling attributes of the local office. The attributes of the signaling network determine the signaling attributes supported by the local office.
Example
Page23
ADD MTP3BOPC
Page24
ADD MTP3BDPC
ADD MTP3BDPC: DPX=0, OPX=0, DPC="401", SLSSM=B0000, STPF=DISABLE, ADJF=TRUE, DPN="RNC Iu Interface";
Page25
ADD MTP3BLKS
Configure the MTP3B signaling link set between the SGSN and the RNC.
Page26
ADD MTP3BRT
Configure the MTP3B signaling route between the SGSN and the RNC.
Page27
ADD TRAFFIC
The IPoA links of the user plane and control plane over the Iu interface use different types of QoS. This command must be executed before the MTP3B link is configured.
Page28
Page29
ADD MTP3BLNK
Configure the signaling link between the SGSN9810 and the RNC. When the configuration of this command takes effect, the SGSN9810 generates an SAAL link. An SAAL link corresponds to an MTP3B link. Example
ADD MTP3BLNK: LNK=1, IFSRN=0, IFSN=12, IFPORT=0, PVPI=1, PVCI=100, SRN=0, SN=2, PRN=0, LSX=1, SLC=0, STRAFI=30;
Page30
SET MTP3BTMR
The default value is recommended. If the default value is used, this command need not be configured.
Page31
ADD SCCPOPC
Page32
ADD SCCPDPC
Page33
ADD SCCPSSN
Configure the subsystem number related to the Iu interface for the SGSN.
ADD SCCPSSN: SSNX=1, SSN=SCMG, NI=NATB, DPC="401", OPC="A00", SSNNAME="scmg"; ADD SCCPSSN: SSNX=2, SSN=RANAP, NI=NATB, DPC="401", OPC="A00", SSNNAME="RANAP";
Page34
ADD RNC
Page35
ADD IUPAGING
This command is used to configure the information about the paging. The SGSN searches for the specific RNC based on the information, and then sends paging to the RNC through signaling.
Example:
Page36
add a direct user plane IP link between the RNC and the EPU. "Direct" means the link does not need to be routed by other EPU.
ADD RNCPFLNK
Page37
Step 18: Set the IP address for the user plane of the Iu interface.
ADD IFIP
This command is used to configure the IP addresses for both the active port and sub-interface on the EPU board.
ADD IFIP: SRN=0, SN=12, PN=0, IPT=PRI, IP="10.110.0.1", MSK="255.255.255.0", DESC="interface to RNC1";
IP1
IPOA
EPU
IP2
IP3 RNC
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.
IP4 SGSN
Page38
Step 19: Define the IPoA link traffic on the user plane.
ADD TRAFFIC
Add a traffic record related to the IPoA link. The IPoA links of the user plane and control plane of the Iu interface use different types of QoS.
Example:
Page39
ADD IPOA
Configure the IPoA link for the user plane of the Iu interface.
Page40
ADD IPRT
Configure the IPoA route for the user plane of the Iu interface.
Page41
Page42
The DSP GTPPATH command is used to display the user plane status.
Page43
Contents
1. Basic Concepts
Page44
Iu over IP
RNANP SCCP M3UA SCTP
M3UA link
RNANP SCCP IP
M3UA
SCTP
IP
IP
GTP_U UDP
IP
GTP_U UDP
Page45
IP
IP
Iu over IP Network
10.110.0.3/24
R
10.10.10.2/24 10.110.0.1/24
DPC=3333
OPC=1111 SGP
100.1.1.1
EPU
l l l
ECU
RNC
SGSN
Ethernet interface Logical IP address
Page46
Configuration Procedure
Step Description Command Configure the hardware and ports. ADD BRD Configure board Configure process group 1 configure IP address Set port property Act port Configure M3UA 2 3 ADD PROCESSGRP ADD IFIP MOD PORT ACT PORT
Page47
Configuration Procedure
Step 4 5 6 7 8 Description Configure M3UA. Add the M3UA destination entity. Add the M3UA signaling link set. Add the M3UA signaling route. Add the M3UA signaling link. Add the IP route to the destination entity. ADD M3DE ADD M3LKS ADD M3RT ADD M3LNK ADD IPRT Command
Page48
Configuration Procedure
Step
9 10 11
Purpose
Configure the SCCP layer. Add the SCCP OPC. Add the SCCP DPC. Add the SCCP subsystem. Configure the RNC.
Command
ADD SCCPOPC ADD SCCPDPC ADD SCCPSSN
12 13 14
ADD RNCPFLNK
Page49
Configuration Procedure
Step
Purpose
Configure the user plane information. Configure the UPIU port on the user plane. Add routes. Configure the GTPU IP address
Command
ADD IFIP ACT PORT ADD IPRT ADD BINDGTPUIP
15(Optional) 16 17
Page50
ADD BRD
ADD PROCESSGRP
Add the process group on the ECU and EPU. Refer to the information about Iu over ATM.
ADD IFIP
Page51
ADD BRDIP
This command is used to set the IP address for the EPU. This IP address is used to set up the M3UA link.
Page52
ADD M3LE
ADD M3DE
ADD M3DE: DEX=0, LEX=0, DPC="3333", SLSSM=B0000, DET=IPSP, ADJF=TRUE, PVER=RFC3332, DEN="rnc";
Page53
HLR
IPSP
IPSP
SGSN
M3UA link
SG
MTP3 link
HLR
ASP
SGP
SP
Page54
ADD M3LKS
ADD M3RT
Page55
ADD M3LNK
ADD M3LNK: SRN=0, SN=2, PN=0, LNK=0, IPT=IPV4, LOCIPV41="10.10.12.14", LOCPORT=2096, PEERIPV41="10.11.12.12", PEERPORT=2907, CS=C, LSX=0, LKN="link 1", CHKSUMTYPE=CRC32;
Page56
ADD IPRT
Page57
Step 9 through Step 13 are used to configure the SCCP layer. The configuration procedure is the same as that for the Iu over ATM interface.
Page58
add a direct user plane IP link between the RNC and the EPU. "Direct" means the link does not need to be routed by other EPU.
ADD RNCPFLNK
Page59
ACT PORT
ADD IFIP
In this example, the user plane and control plane use the
same port.
Page60
ADD IPRT
Page61
ADD BINDGTPUIP
Add IP address of a board to serve as the IP address of the GTP user plane.
Page62
Page63
Thank you
www.huawei.com