Академический Документы
Профессиональный Документы
Культура Документы
PURPOSE:
Digital Pilling Tester is used to check the pilling resistance of the fabric. Pilling is a fabric surface fault characterized by little pills of entangled fibers clinging to the surface.
Pills are formed during wearing or washing by the entanglement of the loose fibers, which protrude from fabric surface. To determine the tendency to form pills, test specimens taken from the fabric sample are rubbed against each other under controlled conditions.
PROCEDURE:
The very first step is to clean the boxes thoroughly. Then place four mounted test specimens in each box and close the boxes. Later set the pre-set counter at 18000 with the help of the Thumb Wheel setting provided on the Digital Counter. Press the start button. The machine would stop automatically after 18000 revolutions. Now, finally take the specimens and compare them with the photographic rating standards.
PURPOSE:
AATCC Water Penetration Tester (Hydrostatic Pressure Tester) is designed and manufactured according to AATCC127-1989 (American Association of Textile Chemists and Colorists).
The main function of these water penetration testers is to test the endurance of waterproof fabric, cloth or other material, as exposed to
water.
APPLICATIONS:
Water Pressure Method Certain Water Pressure Method Water leakage Method
TECHNICAL SPECIFICATION OF WATER PENETRATION TESTER (HYDROSTATIC PRESSURE TESTER): Model: Dimension Pressurization diameter Pressure range Pressure speed QC-317-180 QC-317-350
52 x 64 x 270 cm (21x26x107 60 x 70 x 430 cm (24x28x170 in) in) 4.5 Inch 0 ~ 180 cm H20 1 ~ 3 cm H20/sec 0 ~ 350 cm H20
Weight
This state-of-the-art dyeing rubbing tester allows the user to judge the color firmness of dyeing or printed materials. The abrasive hammer is wrapped with either a dry or wet white cotton cloth, thus allowing abrasion of the colored sample with certain loads and times. The sample is then compared with a grayscale to judge the color firmness.
Testing quantity: 6 pcs/each time Specimen size: 22 x 3 cm White cotton cloth size: 8 x 8 cm Abrasion speed: 30 CPM Load Cell: 200g / 500g, adjustable Abrasion distance: 100 mm White cotton cloth abrasion area: about 1 cm2 With counter, auto-brake when the number of times is up to pre-set
STRUCTURE:
This machine is structured by a table, Abrasion Hammer, Load shaft, Motor, Eccentric Wheel, reduction gear, Counter & Base. Table: Made of copper plate, diameter 200 mm (chambered), with 6 sets of grips Abrasion Hammer: Total 6 pcs. Length/width 20mm, surface diameter 45 mm cambered. Additional load cell 300g is available upon options Load Shaft: One end attached on fixed shaft, the other end connected with abrasion hammer. The distance between fixed shaft and abrasion hammer is 110 mm. Load shaft could rotate around fix shaft. Eccentric Wheel: It drives table by horizontal motion, shuttle within 120 mm, per minute/30 times. Counter: For setting total testing times, it counts each movement of table, and automatically stops when total movement achieves the number of set-times.
Speed
Hamm er load Cloth rubbing area Rubbing distance Dimension Weight Power
30 CPM
100g, 200g, 500g 1 cm2 10 cm 40 x 55 x 33 cm (15.7 x 21.7 x 13) 58 kg 1 Phase, AC220V, 50/60 Hz, 3A (Specified b
10 lb 20 sets
20 x 8 x 20 cm 7 kg None
TEST METHOD:
A compound specimen is used to soak in artificial perspiration resolution (separately in acid and alkali) completely. Natural dry for 30 minutes, then use this tester to apply a constant pressure. The specimen is then put in 37C drying oven for 4 hours. The specimen is removed, left to completely dry, then compared with a gray scale to evaluate the perspiration-resistance level. (Suitable for all fiber).
SPECIFICATION: Hard plastic board: 15 x 63 x 3 mm, 21 pcs Specimen load: 10 lbs Supporting rack: Whole structured by stainless steel, specimen above for increasing pressure. It is able to keep specimen's shape and maintain specimen vertical position; with "spring pressure rack", able to keep the specimen position and shape. It can also keep the position under a regulated temperature-drying oven.
Spray Tester:
PURPOSE:
The Spray Tester is suitable for any fibrous textile processed by waterproof treatment. This tester is used to inspect the textiles wetting resistance on the surface. Suitable for all kinds of water-proof cloth, raincoat cloth, umbrella cloth, textile and fiber cloth. Fix specimen on round frame to avoid wrinkles and set the specimen on the testing stand adjusted to a 45 degrees angle. Pour 250cc. of water into a glass funnel for dipping on specimen, which may take 25-30 seconds. Test three times in order to get an average value to observe the absorption degree in order to realize the waterproof degree of the surface.
Dimensions
Weight
27 33 66 cm
14kg